MC14504B Hex Level Shifter for TTL to CMOS or CMOS to CMOS The MC14504B is a hex non-inverting level shifter using CMOS technology. The level shifter will shift a TTL signal to CMOS logic levels for any CMOS supply voltage between 5 and 15 volts. A control input also allows interface from CMOS to CMOS at one logic level to another logic level: Either up or down level translating is accomplished by selection of power supply levels VDD and VCC. The VCC level sets the input signal levels while VDD selects the output voltage levels. http://onsemi.com MARKING DIAGRAMS 16 * UP Translates from a Low to a High Voltage or DOWN Translates * * * * * PDIP-16 P SUFFIX CASE 648 from a High to a Low Voltage Input Threshold Can Be Shifted for TTL Compatibility No Sequencing Required on Power Supplies or Inputs for Power Up or Power Down 3 to 18 Vdc Operation for VDD and VCC Diode Protected Inputs to VSS Capable of Driving Two Low-Power TTL Loads or One Low-Power Schottky TTL Load Over the Rated Temperature Range MC14504BCP AWLYYWW 1 16 SOIC-16 D SUFFIX CASE 751B 14504B AWLYWW 1 16 TSSOP-16 DT SUFFIX CASE 948F 14 504B ALYW MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.) Symbol Parameter Value Unit VCC DC Supply Voltage Range -0.5 to +18.0 V VDD DC Supply Voltage Range -0.5 to +18.0 V Vin Input Voltage Range (DC or Transient) -0.5 to +18.0 V Vout Output Voltage Range (DC or Transient) -0.5 to VDD + 0.5 V Input or Output Current (DC or Transient) per Pin 10 mA PD Power Dissipation, per Package (Note 3.) 500 mW TA Ambient Temperature Range -55 to +125 C Tstg Storage Temperature Range -65 to +150 C TL Lead Temperature (8-Second Soldering) 260 C Iin, Iout This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS (Vin or Vout) VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open. August, 2000 - Rev. 4 16 SOEIAJ-16 F SUFFIX CASE 966 MC14504B ALYW 1 2. Maximum Ratings are those values beyond which damage to the device may occur. 3. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/C From 65C To 125C Semiconductor Components Industries, LLC, 2000 1 1 A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week ORDERING INFORMATION Device Package Shipping MC14504BCP PDIP-16 2000/Box MC14504BD SOIC-16 48/Rail MC14504BDR2 SOIC-16 2500/Tape & Reel MC14504BDT TSSOP-16 96/Rail MC14504BF SOEIAJ-16 See Note 1. MC14504BFEL SOEIAJ-16 See Note 1. 1. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative. Publication Order Number: MC14504B/D MC14504B PIN ASSIGNMENT VCC 1 16 VDD Aout 2 15 Fout Ain 3 14 Fin Bout 4 13 MODE Bin 5 12 Eout Cout 6 11 Ein Cin 7 10 Dout VSS 8 9 Din LOGIC DIAGRAM VDD VCC LEVEL SHIFTER INPUT OUTPUT TTL/CMOS MODE SELECT MODE Mode Select Input Logic Levels Output Logic Levels 1 (VCC) TTL CMOS 0 (VSS) CMOS CMOS 1/6 of package shown. http://onsemi.com 2 MC14504B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIII III II IIIII IIIIIIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIII I II II III III III IIII III II III III III IIIII IIIIIIII IIII IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII III II III III III IIII III II III III II II IIIIIIIIIII IIII III III III III IIII III III III IIIIIIIIIII IIII III II III III III IIII III II III III II II IIIIIIIIIII IIII III III III III IIII III III III IIIIIIIIIII IIII IIIII III III III IIII IIIII III III IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III III III III IIII III III III II II II II IIIIIIIIIII IIII III III III III IIII III III III IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII IIIII III III III IIII IIIII III III II II IIIIIIIIIII IIII III III III III IIII III III III IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII IIIII III III III IIII IIIII III III IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III III III III IIII III III III II II IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIII IIII IIIII III III III IIII IIIII III III ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) - 55C 25C VCC Vdc VDD Vdc Min Max Min VOL -- -- -- 5.0 10 15 -- -- -- 0.05 0.05 0.05 -- -- -- VOH -- -- -- 5.0 10 15 4.95 9.95 14.95 -- -- -- 5.0 5.0 5.0 5.0 10 10 15 10 15 15 -- -- -- -- -- 5.0 5.0 5.0 5.0 10 10 15 10 15 15 -- -- -- -- IOL Input Current Input Capacitance (Vin = 0) 125C Max Min Max Unit 0 0 0 0.05 0.05 0.05 -- -- -- 0.05 0.05 0.05 Vdc 4.95 9.95 14.95 5.0 10 15 -- -- -- 4.95 9.95 14.95 -- -- -- Vdc 0.8 0.8 1.5 1.5 3.0 -- -- -- -- -- 1.3 1.3 2.25 2.25 4.5 0.8 0.8 1.5 1.5 3.0 -- -- -- -- -- 0.8 0.8 1.4 1.5 2.9 2.0 2.0 3.6 3.6 7.1 -- -- -- -- -- 2.0 2.0 3.5 3.5 7.0 1.5 1.5 2.75 2.75 5.5 -- -- -- -- -- 2.0 2.0 3.5 3.5 7.0 -- -- -- -- -- 5.0 5.0 10 15 - 3.0 -0.64 - 1.6 - 4.2 -- -- -- -- - 2.4 -0.51 - 1.3 - 3.4 - 4.2 - 0.88 - 2.25 - 8.8 -- -- -- -- - 1.7 -0.36 - 0.9 - 2.4 -- -- -- -- -- -- -- 5.0 10 15 0.64 1.6 4.2 -- -- -- 0.51 1.3 3.4 0.88 2.25 8.8 -- -- -- 0.36 0.9 2.4 -- -- -- mAdc Iin -- 15 -- 0.1 -- 0.00001 0.1 -- 1.0 Adc Cin -- -- -- -- -- 5.0 7.5 -- -- pF IDD or ICC -- -- -- 5.0 10 15 -- -- -- 0.05 0.10 0.20 -- -- -- 0.0005 0.0010 0.0015 0.05 0.10 0.20 -- -- -- 1.5 3.0 6.0 Adc Quiescent Current (Per Package) TTL-CMOS Mode IDD 5.0 5.0 5.0 5.0 10 15 -- -- -- 0.5 1.0 2.0 -- -- -- 0.0005 0.0010 0.0015 0.5 1.0 2.0 -- -- -- 3.8 7.5 15 Adc Quiescent Current (Per Package) TTL-CMOS Mode ICC 5.0 5.0 5.0 5.0 10 15 -- -- -- 5.0 5.0 5.0 -- -- -- 2.5 2.5 2.5 5.0 5.0 5.0 -- -- -- 6.0 6.0 6.0 mAdc Characteristic Output Voltage Vin = 0 V Symbol "0" Level "1" Level Vin = VCC Input Voltage "0" Level (VOL = 1.0 Vdc) TTL-CMOS (VOL = 1.5 Vdc) TTL-CMOS (VOL = 1.0 Vdc) CMOS-CMOS (VOL = 1.5 Vdc) CMOS-CMOS (VOL = 1.5 Vdc) CMOS-CMOS VIL Input Voltage "1" Level (VOH = 9.0 Vdc) TTL-CMOS (VOH = 13.5 Vdc) TTL-CMOS (VOH = 9.0 Vdc) CMOS-CMOS (VOH = 13.5 Vdc) CMOS-CMOS (VOH = 13.5 Vdc) CMOS-CMOS VIH Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) IOH (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Quiescent Current (Per Package) CMOS-CMOS Mode Source Sink Typ (4.) Vdc Vdc mAdc 4. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. http://onsemi.com 3 MC14504B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIII IIIIII III IIII IIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIII IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIII IIIII IIIIII III IIII III IIII III III SWITCHING CHARACTERISTICS (CL = 50 pF, TA = 25C) Characteristic Propagation Delay, High to Low Propagation Delay, Low to High Output Rise and Fall Time Symbol tPHL tPLH tTLH, tTHL Limits Shifting Mode VCC Vdc VDD Vdc Min Typ (5.) Max TTL - CMOS VDD > VCC 5.0 5.0 10 15 -- -- 140 140 280 280 CMOS - CMOS VDD > VCC 5.0 5.0 10 10 15 15 -- -- -- 120 120 70 240 240 140 CMOS - CMOS VCC > VDD 10 15 15 5.0 5.0 10 -- -- -- 185 185 175 370 370 350 TTL - CMOS VDD > VCC 5.0 5.0 10 15 -- -- 170 160 340 320 CMOS - CMOS VDD > VCC 5.0 5.0 10 10 15 15 -- -- -- 170 170 100 340 340 200 CMOS - CMOS VCC > VDD 10 15 15 5.0 5.0 10 -- -- -- 275 275 145 550 550 290 ALL -- -- -- 5.0 10 15 -- -- -- 100 50 40 200 100 80 5. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. http://onsemi.com 4 Unit ns ns ns MC14504B 7 VSp , INPUT SWITCHPOINT VOLTAGE (Vdc) VSp , INPUT SWITCHPOINT VOLTAGE (Vdc) 7 6 VCC = 10 V 5 4 3 VCC = 5 V 2 1 6 5 4 3 2 1 0 0 0 5 10 15 VDD, SUPPLY VOLTAGE (Vdc) 20 0 Figure 1. Input Switchpoint CMOS to CMOS Mode 20 20 EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE 15 10 5 5 10 15 VDD, SUPPLY VOLTAGE (Vdc) 20 Figure 2. Input Switchpoint TTL to CMOS Mode VDD, SUPPLY VOLTAGE (Vdc) VDD, SUPPLY VOLTAGE (Vdc) VCC = 5 V EE EE EE EE EE EE EE EE 15 10 0 5 0 0 5 10 15 VCC, SUPPLY VOLTAGE (Vdc) 20 0 Figure 3. Operating Boundary CMOS to CMOS Mode 5 10 15 VCC, SUPPLY VOLTAGE (Vdc) 20 Figure 4. Operating Boundary TTL to CMOS Mode http://onsemi.com 5 MC14504B PACKAGE DIMENSIONS PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R -A- 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B F C DIM A B C D F G H J K L M S L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 C SEATING PLANE J M D 16 PL 0.25 (0.010) MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 SOIC-16 D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J -A- -T- INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 M T B S A S http://onsemi.com 6 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019 MC14504B PACKAGE DIMENSIONS TSSOP-16 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948F-01 ISSUE O 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S K EEE CCC CCC EEE K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. 8 1 N 0.15 (0.006) T U S 0.25 (0.010) A -V- M N NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE DETAIL E H D G http://onsemi.com 7 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0 8 INCHES MIN MAX 0.193 0.200 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0 8 MC14504B PACKAGE DIMENSIONS SOEIAJ-16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966-01 ISSUE O 16 LE 9 Q1 M E HE 1 8 L DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 0 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 0 0.028 0.035 --0.031 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2745 Email: r14525@onsemi.com EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (Mon-Fri 2:30pm to 7:00pm CET) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (Mon-Fri 2:00pm to 7:00pm CET) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (Mon-Fri 12:00pm to 5:00pm GMT) Email: ONlit@hibbertco.com ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, UK For additional information, please contact your local Sales Representative. http://onsemi.com 8 MC14504B/D