RF Chip Inductors
Wire-Wound - 0402, 0603, 0805, 1008, 1206
Pulse Electronics - leading supplier of magnetics for consumer applications
WC701.O (1/14) www.pulseelectronics.com i
Pulse Jack
E l e c t r o n i c s
Table of Contents
Part Number Legend ................................ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Selection Guide .................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Performance Specifications
Environmental Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mechanical Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Tape and Reel Specification . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Miniature Wire-wound RF Chip Inductors
0402CD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
0603CD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
0805CD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-13
0805CM Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
0805FT Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17
1008CD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
1008CM Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
1008CQ Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-24
1206CD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..25-27
The 0402 to 1206 series range of Miniature Chip Inductors contains the very latest in wire-wound technology and
Ceramic or Ferrite Core, thus providing the ultimate in performance demanded by today's Wireless products. The
Inductors provide high Q and SRFs in an industry standard size and footprint. Pulse chip inductors manufactured
after February 2005 are in compliance with RoHS requirements.
2 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
PE 0805 CD 121 K T T
WIRE-WOUND RF CHIP INDUCTORS
PACKAGE STYLE
(0402, 0603, 0805, 1008, or 1206)
INDUCTANCE (nH)
Representative of
the inductance value
CORE MATERIAL
C = Ceramic (Alumina) CQ = High Q
CD = Standard range FT = Ferrite
CM = Alternative performance/inductance to CD
TERMINATION
T = Gold or Tin plating (Gold plating is
priority)
G = Gold plating only
S = Tin plating only
TOLERANCE
G = ±2% K = ±10%
J = ±5%
PART NUMBER LEGEND
Size 0402 0603 0805 1008 1206
PCs/Reel 3000 2000 2000 1600 3000
PACKAGING (T = Tape & Reel: 7" or
13" reel)
WC701.O (1/14) www.pulseelectronics.com 3
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP INDUCTORS
SELECTION GUIDES
*Table for “SMD Antennas for Wireless Devices” continued on next page
➔
Electrical Specifications
Part
Number Size Construction
Inductance
(nH)
CD Series: Standard 100% compatible with other market leaders.
CM Series: Oers improved electrical performance or alternative inductance values to Pulse CD series.
CQ Series: Oers high Q and high Idc series.
FT Series: Ferrite core oers higher inductance values.
0402CD
0603CD
0805CD
0805CM
0805FT
1008CD
1008CM
1008CQ
1206CD
0402
0603
0805
0805
0805
1008
1008
1008
1206
Wirewound
Wirewound
Wirewound
Wirewound
Wirewound
Wirewound
Wirewound
Wirewound
Wirewound
1.0 to 120
1.6 to 390
2.8 to 1500
3.3 to 820
1000 to 68000
9.7 to 8200
10 to 4700
4.1 to 390
3.3 to 1200
11
10 10
100 100 100
Competition Cross Reference
Type Competition 0402CD 0603CD 0805CD 0805FT 1008CQ 1008CD 1206CD
Coilcraft
Murata
TDK
Taiyo
Yuden
0402CS 0603CS 1008HQ 1206CS
LQW1608A LQN21A
LB2012T LEM_2520T
NL2016 NLH2520
0805CS/
HS/HT
1008CS/
HT/CT
Pulse Wire-Wound Inductors
4 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP INDUCTORS
PERFORMANCE TESTING
Electrical Testing
Storage and Operating
Temperature Range:
-40� to +125�C
Thermal:
-40� to +85�C
Mechanical Testing
Temperature Range:
Moisture Resistance
Recommended Solder
Heat Resistance Profile
Operating Life
Inductors are subjected to the
Inductors are subjected to the following:
Use a solder pot at 260C, with RMA Flux. Each
termination is immersed in 63Sn/37Pb molten solder
for 4 to 6 seconds.
There shall be no deformation
There shall be no deformation
Inductance shall not change
Inductance shall not change
Q values shall not change
Q values shall not change
There shall be no Damaged,
Inductors are subjected to 30 cycles
Inductors are subjected to
Inductors are subjected to
10 cycles of 24 hours at 70�C with
1000 hours at 85C with 85%
90 to 95% Relative Humidity
Relative Humidity with
extremes for 48 hours.
or change in appearance
or change in appearance
by more than ±5%
by more than ±5%
by more than ±10%
by more than ±10%
Open or Shorted Windings
for 30 minutes at each extreme.
Then tested at 25�C
Then tested at 25�C
Then tested at 25�C
the rated current applied
WC701.O (1/14) www.pulseelectronics.com 5
Pulse Jack
E l e c t r o n i c s
PERFORMANCE SPECIFICATIONS
WIRE-WOUND RF CHIP INDUCTORS
Electrical Specifications
Mechanical Shock
Moisture Resistance
Electrical Specifications @ 25°C - Operating Temperature -40°C to +125°C
Series
Parts per
Reel A B C D E W P1 P2
P3 H T
0402CD 3000 178 50 13 14.4 8.4 8 2 4 4 1.1 0.3
0603CD 2000 178 50 13 14.4 8.4 8 2 4 4 1.7 0.3
0805CD 2000 178 50 13 14.4 8.4 8 2 4 4 2.1 0.3
0805CM 2000 178 50 13 14.4 8.4 8 2 4 4 2.1 0.3
0805FT 2000 178 50 13 14.4 8.4 8 2 4 4 2.1 0.3
1008CD 1600 178 50 13 14.4 8.4 8 2 4 4 2.6 0.3
1008CM 1600 178 50 13 14.4 8.4 8 2 4 4 2.6 0.3
1008CQ 1600 178 50 13 14.4 8.4 8 2 4 4 2.6 0.3
1206CD 3000 330 101 13 18.4 12.4 12 2 4 4 2.0 0.4
Notes: P1, P2 and P3 are same for all chip inductor series. Keeping the same dimensions for guide hole and pocket pitch (P1), pocket pitch (P2), guide hold pitch (P3)
and tape width (8mm) for all series, enables the packaging machine to maintain the same settings while changing models. The only dierence between the series are
the parts per reel which contributes to a dierent length of tapes/reel per model.
Vibration (Random) Samplers are subjected to random
vibrations as per NAVMAT P9492
The inductors shall withstand
a minimum force of 1000 g's in any
direction usin a dynamometer
force guage.
Inductors are subjected to one half
sine wave pulse (8700 g's for 0.3ms)
in each directional axis for a total of
18 shocks
Reflow Inductors on to test pads using
63 Sn/37 Pb solder paste (IR Reflow
profile = 200�C for 30 seconds or peak
235�C for 20 seconds)
There shall be no deformation
Inductance shall not change
Q values shall not change
or change in appearance
by more than ±5%
by more than ±10%
Tape and Reel Specifications
Reels Dimensions (mm) Tape Dimensions (mm)
6 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
wIRE-wOUND RF CHIP
INDUCTORS - 0402CD SERIES
Wirewound ceramic core construction
High Q values
High self resonant frequency
Industry standard 0402 (1005) surface
mount land pattern
Electrical Specifications @ 25°C
Part Number
Inductance 1
(nH)
Standard
Tolerance
Optional
Tolerance
Q 2
(MIN)
SRF 3
(MHz MIN)
RDC
(MHz MIN)
IDC
(mA MAX)
PE-0402CD3N6KTT 3.6 @ 250MHz ±10% (K) ±5% (J) 20 @ 250MHz 6000 0.066 840
PE-0402CD3N9KTT 3.9 @ 250MHz ±10% (K) ±5% (J) 20 @ 250MHz 5800 0.066 840
PE-0402CD5N6KTT 5.6 @ 250MHz ±10% (K) ±5% (J) 23 @ 250MHz 5800 0.083 760
PE-0402CD6N2KTT 6.2 @ 250MHz ±10% (K) ±5% (J) 23 @ 250MHz 5800 0.083 760
PE-0402CD6N8KTT 6.8 @ 250MHz ±10% (K) ±5% (J) 20 @ 250MHz 5800 0.083 680
PE-0402CD7N5KTT 7.5 @ 250MHz ±10% (K) ±5% (J) 25 @ 250MHz 5800 0.104 680
PE-0402CD8N2KTT 8.2 @ 250MHz ±10% (K) ±5% (J) 25 @ 250MHz 4400 0.104 680
PE-0402CD9N0KTT 9.0 @ 250MHz ±10% (K) ±5% (J) 25 @ 250MHz 4160 0.104 680
PE-0402CD100KTT 10 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 21 @ 250MHz 3900 0.195 480
PE-0402CD150KTT 15 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 26 @ 250MHz 3280 0.172 560
PE-0402CD680KTT 68 @ 250MHz ±10% (K) ±5% (J) 18 @ 250MHz 1840 0.970 100
PE-0402CD820KTT 82 @ 250MHz ±10% (K) ±5% (J) 16 @ 250MHz 1680 1.250 100
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
6. Component Weight: 0.002 grams typical.
WC701.O (1/14) www.pulseelectronics.com 7
Pulse Jack
E l e c t r o n i c s
wIRE-wOUND RF CHIP
INDUCTORS - 0402CD SERIES
Typical Q vs Frequency Typical Inductance vs Frequency
Mechanical
Dimensions:
Unless otherwise specified,
all tolerances are ±
Inches
mm
.010
0,25
Weight ..................0.002grams
Tape & Reel ..............3000/reel
8 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
wIRE-wOUND RF CHIP
INDUCTORS - 0603CD SERIES
Wirewound ceramic core construction
High Q values
High self resonant frequency
Industry standard 0603 (1608) surface
mount land pattern
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-0603CD1N6KTT 1.6 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 24 @ 250MHz >6000 0.030 700
PE-0603CD010KTT 1.7 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 16 @ 250MHz >6000 0.050 700
PE-0603CD1N8KTT 1.8 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 16 @ 250MHz >6000 0.045 700
PE-0603CD2N2KTT 2.2 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 18 @ 250MHz >6000 0.110 700
PE-0603CD3N3KTT 3.3 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz >6000 0.045 700
PE-0603CD3N6KTT 3.6 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 250MHz >6000 0.070 700
PE-0603CD030KTT 3.9 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 250MHz >6000 0.080 700
PE-0603CD4N3KTT 4.3 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 250MHz >6000 0.102 700
PE-0603CD040KTT 4.55 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 250MHz 5800 0.106 700
PE-0603CD4N7KTT 4.7 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 250MHz 5800 0.116 700
PE-0603CD5N1KTT 5.1 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 250MHz 5700 0.108 700
PE-0603CD5N6KTT 5.6 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 250MHz 5500 0.108 700
PE-0603CD6N2KTT 6.2 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 250MHz 5800 0.110 700
PE-0603CD060KTT 6.68 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 250MHz 5800 0.110 700
PE-0603CD6N8KTT 6.8 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 27 @ 250MHz 5800 0.110 700
PE-0603CD7N5KTT 7.5 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 250MHz 4800 0.115 700
PE-0603CD080KTT 8.2 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 250MHz 4600 0.120 700
PE-0603CD8N7KTT 8.7 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 250MHz 4600 0.109 700
PE-0603CD9N5KTT 9.5 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 250MHz 5400 0.135 700
PE-0603CD100KTT 10 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 250MHz 4800 0.130 700
PE-0603CD110KTT 11 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 250MHz 4000 0.086 700
PE-0603CD120KTT 12 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 250MHz 4000 0.130 700
PE-0603CD130KTT 13 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 38 @ 250MHz 3600 0.106 700
PE-0603CD150KTT 15 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 250MHz 4000 0.170 700
PE-0603CD160KTT 16 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 3300 0.170 700
PE-0603CD180KTT 18 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 180MHz 3100 0.170 700
PE-0603CD220KTT 22 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 3000 0.190 700
PE-0603CD230KTT 23 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 38 @ 250MHz 2850 0.190 700
PE-0603CD240KTT 24 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 2650 0.200 600
See page 3 for Competition Cross Reference
(Continued on next page)
12 3 4 5
WC701.O (1/14) www.pulseelectronics.com 9
Pulse Jack
E l e c t r o n i c s
wIRE-wOUND RF CHIP
INDUCTORS - 0603CD SERIES
Electrical Specifications @ 25°C (continued)
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-0603CD270KTT 27 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 2800 0.220 600
PE-0603CD300KTT 30 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 37 @ 250MHz 2250 0.144 600
PE-0603CD330KTT 33 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 2300 0.220 600
PE-0603CD360KTT 36 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 37 @ 250MHz 2080 0.250 600
PE-0603CD390KTT 39 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 2200 0.250 600
PE-0603CD430KTT 43 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 2000 0.280 600
PE-0603CD470KTT 47 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 200MHz 2000 0.280 600
PE-0603CD510KTT 51 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 200MHz 1900 0.270 600
PE-0603CD560KTT 56 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 200MHz 1900 0.310 600
PE-0603CD680KTT 68 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 200MHz 1700 0.340 600
PE-0603CD720KTT 72 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 34 @ 150MHz 1700 0.490 400
PE-0603CD820KTT 82 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 34 @ 150MHz 1700 0.540 400
PE-0603CD101KTT 98.50 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 34 @ 150MHz 1400 0.580 400
PE-0603CDR10KTT 100 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 34 @ 150MHz 1400 0.580 400
PE-0603CD111KTT 110 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 33 @ 150MHz 1300 0.610 300
PE-0603CDR12KTT 120 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 32 @ 150MHz 1300 0.650 300
PE-0603CD121KTT 122 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 33 @ 150MHz 1300 0.650 300
PE-0603CD151KTT 150 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 150MHz 990 0.920 280
PE-0603CD181KTT 180 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 100MHz 990 1.250 240
PE-0603CD211KTT 210 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 27 @ 100MHz 895 2.060 220
PE-0603CD221KTT 220 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 100MHz 900 1.900 200
PE-0603CD251KTT 250 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 100MHz 822 3.550 180
PE-0603CD271KTT 270 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 24 @ 100MHz 860 2.300 170
PE-0603CD331KTT 330 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 22 @ 100MHz 500 2.300 150
PE-0603CD391KTT 390 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 100MHz 350 2.900 130
12 3 4 5
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
6. 5-sides o top side epoxy cap.
(Continued on next page)
10 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0603CD Series
Mechanical
Typical Q vs Frequency Typical Inductance vs Frequency
Dimensions:
Unless otherwise specified,
all tolerances are ±
Inches
mm
.010
0,25
WC701.O (1/14) www.pulseelectronics.com 11
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0805CD SERIES
Wirewound ceramic core construction
High Q values
High self resonant frequency
Industry standard 0805 (2012) surface
mount land pattern
See page 3 for Competition Cross Reference
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-0805CD2N8KTT 2.8 @ 250MHz ±10% (K) ±5% (J) 80 @ 1500MHz >6000 0.06 600
PE-0805CD3N0KTT 3.0 @ 250MHz ±10% (K) ±5% (J) 65 @ 1500MHz >6000 0.06 600
PE-0805CD030KTT 3.32 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 1500MHz 6000 0.08 600
PE-0805CD050KTT 5.6 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 1500MHz 5500 0.10 600
PE-0805CD060KTT 6.5 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 1000MHz 5000 0.11 600
PE-0805CD7N5KTT 7.5 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 1000MHz 4500 0.14 600
PE-0805CD080KTT 7.9 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 1000MHz 4700 0.12 600
PE-0805CD100KTT 10.2 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 4100 0.14 600
PE-0805CD120KTT 11.9 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 4000 0.15 600
PE-0805CD150KTT 14.9 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 3400 0.17 600
PE-0805CD180KTT 17.95 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 3300 0.20 600
PE-0805CD220KTT 21.7 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 2600 0.22 500
PE-0805CD240KTT 24 @250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 2000 0.22 500
PE-0805CD270KTT 26.5 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 2500 0.25 500
PE-0805CD330KTT 32.75 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 2050 0.27 500
PE-0805CD360KTT 36 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 1700 0.27 500
PE-0805CD390KTT 38.5 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 2000 0.29 500
PE-0805CD430KTT 43 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1650 0.34 500
PE-0805CD470KTT 46.6 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1650 0.31 500
PE-0805CD560KTT 55.5 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1550 0.34 500
PE-0805CD680KTT 67.8 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1450 0.38 500
PE-0805CD820KTT 82.7 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1300 0.42 400
PE-0805CD910KTT 91 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 500MHz 1200 0.44 400
PE-0805CD101KTT 98.7 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1200 0.46 400
PE-0805CD111KTT 110 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 250MHz 1000 0.48 400
12 3 4 5
(Continued on next page)
12 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0805CD Series
Electrical Specifications @ 25°C (continued)
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-0805CD121KTT 119.7 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 250MHz 1100 0.51 400
PE-0805CD151KTT 149.4 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 250MHz 920 0.56 400
PE-0805CD181KTT 179.6 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 250MHz 870 0.64 400
PE-0805CD221KTT 217 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 250MHz 850 0.70 400
PE-0805CD241KTT 240 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 44 @ 250MHz 690 1.00 350
PE-0805CD271KTT 269 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 250MHz 650 1.00 350
PE-0805CD331KTT 331 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 250MHz 600 1.40 310
PE-0805CD391KTT 386 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 250MHz 560 1.50 290
PE-0805CD471KTT 477 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 33 @ 100MHz 375 1.76 250
PE-0805CD561KTT 545 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 23 @ 50MHz 340 1.90 230
PE-0805CD681KTT 674 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 23 @ 50MHz 188 2.20 190
PE-0805CD821KTT 783 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 23 @ 50MHz 215 2.35 180
PE-0805CD102KTT 1000 @25MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 50MHz 200 3.60 150
PE-0805CD122KTT 1200 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 50MHz 200 4.10 120
PE-0805CD152KTT 1500 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 50MHz 200 5.00 100
12 3 4 5
*** For other inductance values in 0805 size, please refer to 0805CM (page 14) an 0805FT (page 16). ***
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
Typical Q vs Frequency Typical Inductance vs Frequency
WC701.O (1/14) www.pulseelectronics.com 13
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0805CD SERIES
Mechanical
Dimensions:
Unless otherwise specified,
all tolerances are ±
Inches
mm
.010
0,25
Weight ..................0.012grams
Tape & Reel ..............2000/reel
14 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0805CM SERIES
Wirewound ceramic core construction
High Q values
High self resonant frequency
Industry standard 0805 (2012) surface
mount land pattern
See page 3 for Competition Cross Reference
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-0805CM030KTT 3.3 @ 250MHz ±10% (K) ±5% (J) 37 @ 1500MHz 5000 0.08 600
PE-0805CM060KTT 6.8 @ 250MHz ±10% (K) ±5% (J) 46 @ 1000MHz 5000 0.15 600
PE-0805CM080KTT 8.2 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 47 @ 1000MHz 3900 0.13 600
PE-0805CM100KTT 10 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 3900 0.10 600
PE-0805CM120KTT 12 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 2900 0.13 600
PE-0805CM150KTT 15 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 2700 0.15 600
PE-0805CM180KTT 18 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 50 @500MHz 2600 0.13 600
PE-0805CM220KTT 22 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 2200 0.13 500
PE-0805CM270KTT 27 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 2000 0.23 500
PE-0805CM330KTT 33 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 58 @ 500MHz 1800 0.18 500
PE-0805CM390KTT 39 @ 250MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1600 0.23 500
PE-0805CM470KTT 47 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1650 0.25 500
PE-0805CD560KTT 56 @200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1300 0.16 500
PE-0805CM680KTT 68 @ 200MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1350 0.18 500
PE-0805CM820KTT 82 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 500MHz 1300 0.36 400
PE-0805CM101KTT 100 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 1100 0.36 400
PE-0805CM121KTT 120 @ 150MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 250MHz 1100 0.56 350
PE-0805CM151KTT 150 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 250MHz 900 0.56 350
PE-0805CM181KTT 180 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 250MHz 875 0.69 300
PE-0805CM221KTT 220 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 250MHz 800 0.85 300
PE-0805CM271KTT 270 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 100MHz 800 0.90 300
PE-0805CM331KTT 330 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 100MHz 775 1.28 300
PE-0805CM391KTT 390 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 100MHz 725 1.70 300
PE-0805CM471KTT 470 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 38 @ 100MHz 600 3.25 240
PE-0805CM561KTT 560 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 100MHz 600 3.10 240
PE-0805CM681KTT 680 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 32 @ 50MHz 550 3.50 240
PE-0805CM821KTT 820 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 23 @ 50MHz 215 2.35 200
12 3 4 5
(Continued on next page)
WC701.O (1/14) www.pulseelectronics.com 15
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0805CM SERIES
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
Typical Q vs Frequency Typical Inductance vs Frequency
Dimensions:
Unless otherwise specified,
all tolerances are ±
Inches
mm
.010
0,25
Weight ..................0.012grams
Tape & Reel ..............2000/reel
Mechanical
16 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 0805FT SERIES
Wirewound ceramic core construction
High Q values and resonant frequency
Industry standard 0805 (2012) surface
mount land pattern
See page 3 for Competition Cross Reference
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-0805FT102KTT 1.0 @ 7.96MHz ±10% (K) ±5% (J) 15 @ 7.96MHz 63 1.20 245
PE-0805FT152KTT 1.5 @ 7.96MHz ±10% (K) ±5% (J) 15 @ 7.96MHz 60 1.45 225
PE-0805FT222KTT 2.2 @ 7.96MHz ±10% (K) ±5% (J) 15 @ 7.96MHz 58 1.80 200
PE-0805FT332KTT 3.3 @ 7.96MHz ±10% (K) ±5% (J) 15 @ 7.96MHz 50 2.30 175
PE-0805FT472KTT 4.7 @ 7.96MHz ±10% (K) ±5% (J) 15 @ 7.96MHz 43 2.80 140
PE-0805FT682KTT 6.8 @ 7.96MHz ±10% (K) ±5% (J) 15 @ 7.96MHz 36 3.40 115
PE-0805FT103KTT 10 @ 2.52MHz ±10% (K) ±5% (J) 10 @ 2.52MHz 30 4.70 98
PE-0805FT153KTT 15 @ 2.52MHz ±10% (K) ±5% (J) 10 @ 2.52MHz 23 6.50 80
PE-0805FT223KTT 22 @ 2.52MHz ±10% (K) ±5% (J) 10 @ 2.52MHz 20 8.00 68
PE-0805FT333KTT 33 @ 2.52MHz ±10% (K) ±5% (J) 10 @ 2.52MHz 17 10.70 60
PE-0805FT473KTT 47 @ 2.52MHz ±10% (K) ±5% (J) 10 @ 2.52MHz 14 13.80 55
PE-0805FT683KTT 68 @ 2.52MHz ±10% (K) ±5% (J) 8 @ 2.52MHz 11 17.50 49
12 3 4 5
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
WC701.O (1/14) www.pulseelectronics.com 17
Pulse Jack
E l e c t r o n i c s
CONNECTOR PRODUCTS
Dimensions:
Unless otherwise specified,
all tolerances are ±
Inches
mm
.010
0,25
Weight ..................0.012grams
Tape & Reel ..............2000/reel
Typical Q vs Frequency Typical Inductance vs Frequency
Mechanical
18 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CD SERIES
Wirewound ceramic core construction
High Q values and high self-esonant frequency
Industry standard 1008 (2520) surface mount
land pattern
See page 3 for Competition Cross Reference
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1008CD090KTT 9,7 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 4100 0.09 1000
PE-1008CD100KTT 10 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 4100 0.09 1000
PE-1008CD120KTT 12 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 3300 0.09 1000
PE-1008CD140KTT 14,3 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 1850 0.10 1000
PE-1008CD150KTT 15 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 1850 0.10 1000
PE-1008CD180KTT 17, 8 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 350MHz 2500 0.11 1000
PE-1008CD210KTT 20, 9 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 350MHz 1800 0.12 1000
PE-1008CD220KTT 22 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 350MHz 1800 0.12 1000
PE-1008CD260KTT 26,2 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 350MHz 1500 0.13 1000
PE-1008CD270KTT 27 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 350MHz 1500 0.11 1000
PE-1008CD320KTT 31,8 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1600 0.16 1000
PE-1008CD330KTT 33 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1600 0.14 1000
PE-1008CD380KTT 38,2 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1400 0.15 1000
PE-1008CD390KTT 39 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1400 0.12 1000
PE-1008CD450KTT 44,9@ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 1200 0.16 1000
PE-1008CD470KTT 47 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 1200 0.08 1000
PE-1008CD540KTT 54 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 1150 0.18 1000
PE-1008CD560KTT 56 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 1150 0.12 1000
PE-1008CD650KTT 65 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @350MHz 1100 0.20 1000
PE-1008CD680KTT 68 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 1100 0.07 1000
PE-1008CD790KTT 79 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 950 0.22 1000
PE-1008CD820KTT 82 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 950 0.14 1000
PE-1008CD960KTT 96, 1 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 350MHz 900 0.56 650
PE-1008CD101KTT 100 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 900 0.15 650
PE-1008CD121KTT 120 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 950 0.63 650
PE-1008CD141KTT 145,7 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 625 0.70 580
PE-1008CD151KTT 150 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 625 0.16 580
12 3 4 5
(Continued on next page)
WC701.O (1/14) www.pulseelectronics.com 19
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CD SERIES
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1008CD161KTT 160 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 625 0.77 600
PE-1008CD171KTT 170,2 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 625 0.77 620
PE-1008CD181KTT 180 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 650 0.77 620
PE-1008CD211KTT 216 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 625 0.84 500
PE-1008CD221KTT 220 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 625 0.84 500
PE-1008CD261KTT 260,5 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 525 0.91 500
PE-1008CD271KTT 270 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 350MHz 525 0.91 500
PE-1008CD311KTT 313,6 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 500 1.05 450
PE-1008CD331KTT 330 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 500 1.05 450
PE-1008CD361KTT 365 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 500 1.12 470
PE-1008CD391KTT 390 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 475 1.12 470
PE-1008CD451KTT 447 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 450 1.19 420
PE-1008CD471KTT 470@ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 450 1.19 420
PE-1008CD541KTT 535 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 415 1.33 310
PE-1008CD561KTT 560 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 415 1.33 310
PE-1008CD591KTT 586 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 375 1.40 300
PE-1008CD621KTT 620 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 375 1.40 300
PE-1008CD641KTT 636 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 375 1.47 230
PE-1008CD681KTT 680 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 375 1.47 230
PE-1008CD711KTT 708,8 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 1100 1.54 200
PE-1008CD751KTT 750 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 950 1.61 200
PE-1008CD771KTT 768 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 950 1.61 180
PE-1008CD821KTT 820 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 900 1.61 180
PE-1008CD851KTT 849.8 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 50MHz 900 1.68 150
PE-1008CD911KTT 909,5 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 50MHz 290 1.75 150
PE-1008CD102KTT 1000 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 50MHz 260 1.90 120
PE-1008CD112KTT 1184 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 50MHz 250 2.00 310
PE-1008CD122KTT 1200 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 35 @ 50MHz 250 2.00 310
PE-1008CD142KTT 1470 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 50MHz 200 2.30 330
PE-1008CD152KTT 1500 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 50MHz 200 2.30 330
PE-1008CD182KTT 1792.9 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 50MHz 160 2.60 300
PE-1008CD212KTT 2154.5 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 50MHz 80 2.80 280
PE-1008CD222KTT 2200 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 28 @ 50MHz 80 2.80 280
PE-1008CD262KTT 2646.8 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 22 @ 50MHz 90 3.20 290
PE-1008CD272KTT 2700 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 22 @ 50MHz 90 3.20 290
12 3 4 5
(Continued on next page)
20 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CD SERIES
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1008CD322KTT 3207.6 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 22 @ 25MHz 40 3.40 290
PE-1008CD332KTT 3300 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 22 @ 25MHz 40 3.40 290
PE-1008CD372KTT 3758.2 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 25MHz 35 3.60 260
PE-1008CD392KTT 3900 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 25MHz 35 3.60 260
PE-1008CD452KTT 4526.2 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 25MHz 25 4.00 260
PE-1008CD472KTT 4700 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 25MHz 25 4.00 260
PE-1008CD562KTT 5600 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 25MHz 60 5.40 240
PE-1008CD682KTT 6800 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 18 @ 7.9MHz 40 4.90 200
PE-1008CD822KTT 8200 @ 7.9MHz ±10% (K) ±5% (J), ±2% (G) 18 @ 7.9MHz 25 6.00 160
12 3 4 5
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
6. Component Weight: 0.032 grams typical.
7. These components are 0.055" in height.
*** For other inductance values in 1008 size, please refer to 1008CM (page 21-22) and 1008CQ (page 23) ***
Typical Q vs Frequency
Typical Inductance vs Frequency
Dimensions:
Unless otherwise specified, all tolerances are ±
Inches
mm
.010
0,25
Mechanical
WC701.O (1/14) www.pulseelectronics.com 21
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CM SERIES
Wirewound ceramic core construction
High Q values and high self-esonant frequency
Industry standard 1008 (2520) surface mount
land pattern
See page 3 for Competition Cross Reference
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1008CM100KTT 10 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 500MHz 4100 0.09 1000
PE-1008CM120KTT 12 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 500MHz 4100 0.09 1000
PE-1008CM150KTT 15 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 3300 0.09 1000
PE-1008CM180KTT 18 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 1850 0.10 1000
PE-1008CM220KTT 22 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 500MHz 1850 0.10 1000
PE-1008CM270KTT 27 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 2500 0.11 1000
PE-1008CM330KTT 33 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1800 0.18 800
PE-1008CM390KTT 39 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 70 @ 350MHz 1400 0.12 1000
PE-1008CM470KTT 47 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 70 @ 350MHz 1200 0.08 1000
PE-1008CM560KTT 56 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1150 0.12 1000
PE-1008CM680KTT 68 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 70 @ 350MHz 1100 0.07 1000
PE-1008CM820KTT 82 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 950 0.14 950
PE-1008CM101KTT 100 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 65 @ 350MHz 900 0.15 650
PE-1008CM121KTT 120 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 825 0.22 650
PE-1008CM151KTT 150 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 625 0.16 580
PE-1008CM161KTT 160 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 625 0.25 600
PE-1008CM181KTT 180 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 650 0.25 600
PE-1008CM201KTT 200 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 630 0.24 580
PE-1008CM221KTT 220 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 625 0.28 500
PE-1008CM271KTT 270 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 525 0.50 500
PE-1008CM331KTT 330 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 500 0.80 450
PE-1008CM371KTT 370 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 490 0.80 430
PE-1008CM391KTT 390 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 475 0.75 425
PE-1008CM401KTT 400 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 470 0.75 420
PE-1008CM471KTT 470 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 450 0.70 350
PE-1008CM561KTT 560 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 100MHz 425 0.80 350
PE-1008CM621KTT 620 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 375 1.90 200
12 3 4 5
(Continued on next page)
22 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CM SERIES
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1008CM681KTT 680 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 375 2.30 200
PE-1008CM751KTT 750 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 100MHz 350 1.60 200
PE-1008CM821KTT 820 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 100MHz 325 3.30 200
PE-1008CM911KTT 910 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 50MHz 300 2.10 200
PE-1008CM102KTT 1000 @ 25MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 50MHz 300 1.80 200
PE-1008CM122KTT 1200 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 50MHz 250 3.00 200
PE-1008CM152KTT 1500 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 50MHz 200 4.00 150
PE-1008CM182KTT 1800 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 50MHz 150 5.09 150
PE-1008CM222KTT 2200 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 25MHz 80 5.85 150
PE-1008CM272KTT 2700 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 25MHz 90 7.70 150
PE-1008CM332KTT 3300 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 25 @ 15MHz 40 7.80 150
PE-1008CM392KTT 3900 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 20 @ 15MHz 35 8.30 135
PE-1008CM472KTT 4700 @ 10MHz ±10% (K) ±5% (J), ±2% (G) 16 @ 15MHz 25 6.00 150
12 3 4 5
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
6. Component Weight: 0.032 grams typical.
Typical Q vs Frequency
Typical Inductance vs Frequency
Dimensions:
Unless otherwise specified, all tolerances are ±
Inches
mm
.010
0,25
Mechanical
WC701.O (1/14) www.pulseelectronics.com 23
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CQ SERIES
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF Min
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1008CQ4N1KTT 4.1 @ 50MHz ±10% (K) ±5% (J) 75 @ 1500MHz 6000 0.05 1600
PE-1008CQ100KTT 10 @ 50MHz ±10% (K) ±5% (J) 60 @ 500MHz 3600 0.06 1600
PE-1008CQ120KTT 12 @ 50MHz ±10% (K) ±5% (J) 70 @ 500MHz 2800 0.06 1500
PE-1008CQ180KTT 18 @ 50MHz ±10% (K) ±5% (J) 62 @ 350MHz 2700 0.07 1400
PE-1008CQ220KTT 22 @ 50MHz ±10% (K) ±5% (J) 62 @ 350MHz 2050 0.07 1400
PE-1008CQ330KTT 33 @ 50MHz ±10% (K) ±5% (J) 75 @ 350MHz 1700 0.09 1300
PE-1008CQ390KTT 39 @ 50MHz ±10% (K) ±5% (J) 75 @ 350MHz 1300 0.09 1300
PE-1008CQ470KTT 47 @ 50MHz ±10% (K) ±5% (J) 75 @ 350MHz 1450 0.12 1200
PE-1008CQ560KTT 56 @ 50MHz ±10% (K) ±5% (J) 75 @ 350MHz 1230 0.12 1200
PE-1008CQ680KTT 68 @ 50MHz ±10% (K) ±5% (J) 80 @ 350MHz 1150 0.13 1100
PE-1008CQ820KTT 82 @ 50MHz ±10% (K) ±5% (J) 80 @ 350MHz 1060 0.16 1100
PE-1008CQ101KTT 100 @ 50MHz ±10% (K) ±5% (J) 62 @ 350MHz 820 0.16 1000
PE-1008CQ121KTT 120 @ 50MHz ±10% (K) ±5% (J) 62 @ 350MHz 800 0.17 1000
PE-1008CQ151KTT 150 @ 50MHz ±10% (K) ±5% (J) 60 @ 350MHz 750 0.21 950
PE-1008CQ181KTT 180 @ 50MHz ±10% (K) ±5% (J) 40 @ 350MHz 720 0.23 920
PE-1008CQ221KTT 220 @ 50MHz ±10% (K) ±5% (J) 35 @ 350MHz 680 0.29 900
PE-1008CQ271KTT 270 @ 50MHz ±10% (K) ±5% (J) 35 @ 350MHz 600 0.55 600
PE-1008CQ331KTT 330 @ 50MHz ±10% (K) ±5% (J) 35 @ 100MHz 550 0.60 550
PE-1008CQ391KTT 390 @ 50MHz ±10% (K) ±5% (J) 35 @ 350MHz 500 0.82 470
12 3 4 5
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
6. Component Weight: 0.032 grams typical.
Wirewound ceramic core construction
High Q values and Idc values
High self-esonant frequency
Industry standard 1008 (2520) surface mount
land pattern
See page 3 for Competition Cross Reference
24 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1008CQ SERIES
Typical Q vs Frequency Typical Inductance vs Frequency
Dimensions:
Unless otherwise specified, all tolerances are ±
Inches
mm
.010
0,25
Mechanical
WC701.O (1/14) www.pulseelectronics.com 25
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1206CD SERIES
Wirewound ceramic core construction
High Q values and self-esonant frequency
Industry standard 1206 (3216) SMT land pattern
See page 3 for Competition Cross Reference
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF Min
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1206CD030KTT 3.3 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 300MHz 6200 0.05 1000
PE-1206CD060KTT 6.8 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 30 @ 300MHz 5500 0.07 1000
PE-1206CD100KTT 10 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 300MHz 4000 0.08 1000
PE-1206CD120KTT 12 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 300MHz 3200 0.08 1000
PE-1206CD150KTT 15 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 40 @ 300MHz 3200 0.10 1000
PE-1206CD180KTT 18 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 300MHz 2800 0.10 1000
PE-1206CD220KTT 22 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 300MHz 2200 0.10 1000
PE-1206CD270KTT 27 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 50 @ 300MHz 1800 0.11 1000
PE-1206CD330KTT 33 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1800 0.11 1000
PE-1206CD390KTT 39 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1800 0.12 1000
PE-1206CD470KTT 47 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1500 0.13 1000
PE-1206CD560KTT 56 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1450 0.14 1000
PE-1206CD680KTT 68 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1200 0.26 900
PE-1206CD820KTT 82 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1200 0.21 900
PE-1206CD101KTT 100 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 1100 0.26 850
PE-1206CD121KTT 120 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 1100 0.26 800
PE-1206CD151KTT 150 @ 100MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 950 0.31 750
PE-1206CD181KTT 180 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 100MHz 900 0.43 700
PE-1206CD221KTT 220 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 60 @ 350MHz 760 0.50 670
PE-1206CD271KTT 270 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 55 @ 300MHz 730 0.56 630
PE-1206CD331KTT 330 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 650 0.62 590
PE-1206CD391KTT 390 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 600 0.75 530
PE-1206CD471KTT 470 @ 50MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 550 1.30 490
PE-1206CD561KTT 560 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 470 1.34 460
PE-1206CD681KTT 680 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 450 1.58 430
PE-1206CD751KTT 750 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 440 2.25 400
PE-1206CD821KTT 820 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 420 1.82 400
PE-1206CD911KTT 910 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 410 2.95 400
12 3 4 5
(Continued on next page)
26 www.pulseelectronics.com WC701.O (1/14)
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1206CD SERIES
Notes:
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that
inductance information is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture.
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise.
6. Component Weight: 0.035 grams typical.
7. These components are 0.060" in height.
Electrical Specifications @ 25°C
Part Number
Inductance
(nH)
Standard
Tolerance
Optional
Tolerance
Q
(MIN)
SRF Min
(MHz MIN)
RDC
(Ω MAX)
IDC
(mA MAX)
PE-1206CD102KTT 1000 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 400 2.80 320
PE-1206CD122KTT 1200 @ 35MHz ±10% (K) ±5% (J), ±2% (G) 45 @ 150MHz 380 3.20 300
12 3 4 5
Typical Q vs Frequency
Typical Inductance vs Frequency
WC701.O (1/14) www.pulseelectronics.com 27
Pulse Jack
E l e c t r o n i c s
WIRE-WOUND RF CHIP
INDUCTORS - 1206CD SERIES
Mechanical
Dimensions:
Unless otherwise specified, all tolerances are ±
Inches
mm
.010
0,25
For More Information
Pulse Worldwide
Headquarters
12220 World Trade Drive
San Diego, CA 92128
U.S.A.
Tel: 858 674 8100
Fax: 858 674 8262
Pulse Europe
Einsteinstrasse 1
D-71083 Herrenberg
Germany
Tel: 49 7032 78060
Fax: 49 7032 7806 135
Pulse China Headquarters
B402, Shenzhen Academy of
Aerospace Technology Bldg.
10th Kejinan Road
High-Tech Zone
Nanshan District
Shenzen, PR China 518057
Tel: 86 755 33966678
Fax: 86 755 33966700
Pulse North China
Room 2704/2705
Super Ocean Finance Ctr.
2067 Yan An Road West
Shanghai 200336
China
Tel: 86 21 62787060
Fax: 86 2162786973
Pulse South Asia
135 Joo Seng Road
#03-02
PM Industrial Bldg.
Singapore 368363
Tel: 65 6287 8998
Fax: 65 6287 8998
Pulse North Asia
3F, No. 198
Zhongyuan Road
Zhongli City
Taoyuan County 320
Taiwan R. O. C.
Tel: 886 3 4356768
Fax: 886 3 4356823 (Pulse)
Fax: 886 3 4356820 (FRE)
Performance warranty of products oered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be
trademarks or registered trademarks of their respective owners. © Copyright, 2014. Pulse Electronics, Inc. All rights reserved.