DSP56F801/D Rev. 7.0, 1/2002 DSP56F801 Preliminary Technical Data DSP56F801 16-bit Digital Signal Processor * Up to 40 MIPS operation at 80 MHz core frequency * Hardware DO and REP loops * 6-channel PWM Module * DSP and MCU functionality in a unified, C-efficient architecture * Two 4-channel, 12-bit ADCs * MCU-friendly instruction set supports both DSP and controller functions: MAC, bit manipulation unit, 14 addressing modes * Serial Communications Interface (SCI) * Serial Peripheral Interface (SPI) * General Purpose Quad Timer * 8K x 16-bit words Program Flash * JTAG/OnCETM port for debugging * 1K x 16-bit words Program RAM * On-chip relaxation oscillator * 2K x 16-bit words Data Flash * 11 shared GPIO * 1K x 16-bit words Data RAM * 48-pin LQFP Package * 2K x 16-bit words Boot Flash 6 PWM Outputs PWMA RESET Fault Input IRQA 6 VCAPC VDD VSS 2 5* 4 JTAG/ OnCE Port 4 4 A/D1 A/D2 VREF Quad Timer C Program Memory 8188 x 16 Flash 1024 x 16 SRAM Quad Timer D or GPIO Boot Flash 2048 x 16 Flash Data Memory 2048 x 16 Flash 1024 x 16 SRAM 2 4 SCI0 or GPIO SPI or GPIO Program Controller and Hardware Looping Unit * ApplicationSpecific Memory & Peripherals Data ALU 16 x 16 + 36 36-Bit MAC Three 16-bit Input Registers Two 36-bit Accumulators Address Generation Unit * 16-Bit DSP56800 Core XDB2 * * CGDB XAB1 XAB2 * * * IPBB CONTROLS 16 COP RESET MODULE CONTROLS ADDRESS BUS [8:0] IPBus Bridge (IPBB) DATA BUS [15:0] *includes TCS pin which is reserved for factory use and is tied to VSS Figure 1. DSP56F801 Block Diagram (c) Motorola, Inc., 2002. All rights reserved. Bit Manipulation Unit PLL * INTERRUPT CONTROLS 16 COP/ Watchdog Analog Reg PAB PDB VSSA Low Voltage Supervisor ADC Interrupt Controller 3 Digital Reg VDDA Clock Gen or Optional Internal Relaxation Osc. GPIOB3/XTAL GPIOB2/EXTAL Part 1 Overview 1.1 DSP56F801 Features 1.1.1 Digital Signal Processing Core * Efficient 16-bit DSP56800 family DSP engine with dual Harvard architecture * As many as 40 Million Instructions Per Second (MIPS) at 80 MHz core frequency * Single-cycle 16 x 16-bit parallel Multiplier-Accumulator (MAC) * Two 36-bit accumulators including extension bits * 16-bit bidirectional barrel shifter * Parallel instruction set with unique DSP addressing modes * Hardware DO and REP loops * Three internal address buses and one external address bus * Four internal data buses and one external data bus * Instruction set supports both DSP and controller functions * Controller style addressing modes and instructions for compact code * Efficient C compiler and local variable support * Software subroutine and interrupt stack with depth limited only by memory * JTAG/OnCE debug programming interface 1.1.2 Memory * Harvard architecture permits as many as three simultaneous accesses to program and data memory * On-chip memory including a low-cost, high-volume flash solution -- 8K x 16 bit words of Program Flash -- 1K x 16-bit words of Program RAM -- 2K x 16-bit words of Data Flash -- 1K x 16-bit words of Data RAM -- 2K x 16-bit words of Boot Flash * 1.1.3 2 Programmable Boot Flash supports customized boot code and field upgrades of stored code through a variety of interfaces (JTAG, SPI) Peripheral Circuits for DSP56F801 * Pulse Width Modulator (PWM) with six PWM outputs, two Fault inputs, fault-tolerant design with deadtime insertion; supports both center- and edge-aligned modes * Two 12-bit, Analog-to-Digital Converters (ADCs), which support two simultaneous conversions with two 4-multiplexed inputs; ADC and PWM modules can be synchronized * General Purpose Quad Timer: Timer D with three pins (or three additional GPIO lines) * Serial Communication Interface (SCI) with two pins (or two additional GPIO lines) DSP56F801 Preliminary Technical Data MOTOROLA DSP56F801 Description * Serial Peripheral Interface (SPI) with configurable four-pin port (or four additional GPIO lines) * Eleven multiplexed General Purpose I/O (GPIO) pins * Computer-Operating Properly (COP) watchdog timer * One dedicated external interrupt pin * External reset pin for hardware reset * JTAG/On-Chip Emulation (OnCETM) for unobtrusive, processor speed-independent debugging * Software-programmable, Phase Lock Loop-based frequency synthesizer for the DSP core clock * Oscillator flexibility between either an external crystal oscillator or an on-chip relaxation oscillator for lower system cost and two additional GPIO lines 1.1.4 Energy Information * Fabricated in high-density CMOS with 5V tolerant, TTL-compatible digital inputs * Uses a single 3.3V power supply * On-chip regulators for digital and analog circuitry to lower cost and reduce noise * Wait and Stop modes available 1.2 DSP56F801 Description The DSP56F801 is a member of the DSP56800 core-based family of Digital Signal Processors (DSPs). It combines, on a single chip, the processing power of a DSP and the functionality of a microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because of its low cost, configuration flexibility, and compact program code, the DSP56F801 is well-suited for many applications. The DSP56F801 includes many peripherals that are especially useful for applications such as motion control, smart appliances, steppers, encoders, tachometers, limit switches, power supply and control, automotive control, engine management, noise suppression, remote utility metering, and industrial control for power, lighting, and automation. The DSP56800 core is based on a Harvard-style architecture consisting of three execution units operating in parallel, allowing as many as six operations per instruction cycle. The microprocessor-style programming model and optimized instruction set allow straightforward generation of efficient, compact code for both DSP and MCU applications. The instruction set is also highly efficient for C compilers to enable rapid development of optimized control applications. The DSP56F801 supports program execution from either internal or external memories. Two data operands can be accessed from the on-chip data RAM per instruction cycle. The DSP56F801 also provides one external dedicated interrupt lines and up to 11 General Purpose Input/Output (GPIO) lines, depending on peripheral configuration. The DSP56F801 DSP controller includes 8K words (16-bit) of program Flash and 2K words of Data Flash (each programmable through the JTAG port) with 1K words of both program and data RAM. A total of 2K words of Boot Flash is incorporated for easy customer-inclusion of field-programmable software routines that can be used to program the main program and data flash memory areas. Both program and data flash memories can be independently bulk erased or erased in page sizes of 256 words. The Boot Flash memory can also be either bulk or page erased. A key application-specific feature of the DSP56F801 is the inclusion of a Pulse Width Modulator (PWM) module. This modules incorporates six complementary, individually programmable PWM signal outputs to MOTOROLA DSP56F801 Preliminary Technical Data 3 enhance motor control functionality. Complementary operation permits programmable dead-time insertion, and separate top and bottom output polarity control. The up-counter value is programmable to support a continuously variable PWM frequency. Both edge and center aligned synchronous pulse width control (0% to 100% modulation) are supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors), both BDC and BLDC (Brush and Brushless DC motors), SRM and VRM (Switched and Variable Reluctance Motors), and stepper motors. The PWMs incorporate fault protection and cycle-bycycle current limiting with sufficient output drive capability to directly drive standard opto-isolators. A "smoke-inhibit", write-once protection feature for key parameters is also included. The PWM is doublebuffered and includes interrupt control to permit integral reload rates to be programmable from 1 to 16. The PWM modules provide a reference output to synchronize the Analog-to-Digital Converters. The DSP56F801 incorporates an 8 input, 12-bit Analog-to-Digital Converter (ADC). A full set of standard programmable peripherals is provided that include a Serial Communications Interface (SCI), a Serial Peripheral Interface (SPI), and two Quad Timers. Any of these interfaces can be used as General-Purpose Input/Outputs (GPIO) if that function is not required. An on-chip relaxation oscillator provides flexibility in the choice of either on-chip or externally supplied frequency reference for chip timing operations. Application code is used to select which source is to be used. 1.3 "Best in Class" Development Environment The SDK (Software Development Kit) provides fully debugged peripheral drivers, libraries and interfaces that allow programmers to create their unique C application code independent of component architecture. The CodeWarrior Integrated Development Environment is a sophisticated tool for code navigation, compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards support concurrent engineering. Together, the SDK, CodeWarrior, and EVMs create a complete, scalable tools solution for easy, fast, and efficient development. 1.4 Product Documentation The four documents listed in Table 1 are required for a complete description and proper design with the DSP56F801. Documentation is available from local Motorola distributors, Motorola semiconductor sales offices, Motorola Literature Distribution Centers, or online at www.motorola.com/semiconductors/dsp. Table 1. DSP56F801 Chip Documentation Topic 4 Description Order Number DSP56800 Family Manual Detailed description of the DSP56800 family architecture, and 16-bit DSP core processor and the instruction set DSP56800FM/D DSP56F801/803/805/807 User's Manual Detailed description of memory, peripherals, and interfaces of the DSP56F801, DSP56F803, DSP56F805, and DSP56F807 DSP56F801-7UM/D DSP56F801 Technical Data Sheet Electrical and timing specifications, pin descriptions, and package descriptions (this document) DSP56F801/D DSP56F801 Product Brief Summary description and block diagram of the DSP56F801 core, memory, peripherals and interfaces DSP56F801PB/D DSP56F801 Preliminary Technical Data MOTOROLA Data Sheet Conventions 1.5 Data Sheet Conventions This data sheet uses the following conventions: OVERBAR This is used to indicate a signal that is active when pulled low. For example, the RESET pin is active when low. "asserted" A high true (active high) signal is high or a low true (active low) signal is low. "deasserted" A high true (active high) signal is low or a low true (active low) signal is high. Examples: 1. Signal/Symbol Logic State Signal State Voltage1 PIN True Asserted VIL/VOL PIN False Deasserted VIH/VOH PIN True Asserted VIH/VOH PIN False Deasserted VIL/VOL Values for VIL, VOL, VIH, and VOH are defined by individual product specifications. Part 2 Signal/Connection Descriptions 2.1 Introduction The input and output signals of the DSP56F801 are organized into functional groups, as shown in Table 2 and as illustrated in Figure 2. In Table 3 through Table 13, each table row describes the signal or signals present on a pin. Table 2. Functional Group Pin Allocations Number of Pins Detailed Description Power (VDD or VDDA) 5 Table 3 Ground (VSS or VSSA) 6 Table 4 Supply Capacitors 2 Table 5 PLL and Clock 2 Table 6 Interrupt and Program Control 2 Table 7 Pulse Width Modulator (PWM) Port 7 Table 8 Serial Peripheral Interface (SPI) Port1 4 Table 9 Serial Communications Interface (SCI) Port1 2 Table 10 Analog-to-Digital Converter (ADC) Port 9 Table 11 Quad Timer Module Port 3 Table 12 JTAG/On-Chip Emulation (OnCE) 6 Table 13 Functional Group 1. MOTOROLA Alternately, GPIO pins DSP56F801 Preliminary Technical Data 5 Power Port Ground Port Power Port Ground Port VDD 4 VSS 5* VDDA 1 VSSA 1 Other Supply Port VCAPC PLL and Clock or GPIO EXTAL (GPIOB2) XTAL (GPIOB3) TCK TMS JTAG/OnCE Port TDI TDO TRST DE PWMA0-5 6 2 1 FAULTA0 1 SCLK (GPIOB4) 1 MOSI (GPIOB5) 1 MISO (GPIOB6) 1 SS (GPIOB7) 1 TXD0 (GPIOB0) 1 RXD0 (GPIOB1) SCI0 Port or GPIO 8 ANA0-7 ADCA Port 1 VREF 3 TD0-2 (GPIOA0-2) 1 IRQA 1 1 DSP56F801 1 1 1 1 1 RESET SPI Port or GPIO Quad Timer D or GPIO Interrupt/ Program Control 1 1 *includes TCS pin which is reserved for factory use and is tied to VSS Figure 2. DSP56F801 Signals Identified by Functional Group1 1. Alternate pin functionality is shown in parenthesis. 6 DSP56F801 Preliminary Technical Data MOTOROLA Power and Ground Signals 2.2 Power and Ground Signals Table 3. Power Inputs No. of Pins Signal Name Signal Description 4 VDD Power--These pins provide power to the internal structures of the chip, and should all be attached to VDD. 1 VDDA Analog Power--These pins supply an analog power source. Table 4. Grounds No. of Pins Signal Name Signal Description 4 VSS GND--These pins provide grounding for the internal structures of the chip, and should all be attached to VSS. 1 VSSA Analog Ground--This pin supplies an analog ground. 1 TCS TCS--This pin is reserved for factory use and must be tied to VSS for normal use. In block diagrams, this pin is considered an additional V SS. Table 5. Supply Capacitors and VPP No. of Pins Signal Name Signal Type State During Reset 2 VCAPC Supply Supply Signal Description VCAPC - Connect each pin to a 2.2 F bypass capacitor in order to bypass the core logic voltage regulator (required for proper chip operation). For more information, refer to Section 5.2. 2.3 Clock and Phase Lock Loop Signals Table 6. PLL and Clock No. of Pins Signal Name Signal Type State During Reset 1 EXTAL Input Input External Crystal Oscillator Input--This input should be connected to an 8 MHz external crystal or ceramic resonator. For more information, please refer to Section 3.5. GPIOB2 Input/ Output Input Port B GPIO--This multiplexed pin is a General Purpose I/O (GPIO) pin that can be programmed as an input or output pin. This I/O can be utilized when using the on-chip relaxation oscillator so the EXTAL pin is not needed. Signal Description *includes TCS pin which is reserved for factory use and is tied to VSS MOTOROLA DSP56F801 Preliminary Technical Data 7 Table 6. PLL and Clock (Continued) No. of Pins Signal Name Signal Type State During Reset 1 XTAL Output Chipdriven Signal Description Crystal Oscillator Output--This output should be connected to an 8 MHz external crystal or ceramic resonator. For more information, please refer to Section 3.5. This pin can also be connected to an external clock source. For more information, please refer to Section 3.5.3. GPIOB3 Input/ Output Input Port B GPIO--This multiplexed pin is a General Purpose I/O (GPIO) pin that can be programmed as an input or output pin. This I/O can be utilized when using the on-chip relaxation oscillator so the XTAL pin is not needed. 2.4 Interrupt and Program Control Signals Table 7. Interrupt and Program Control Signals No. of Pins Signal Name Signal Type State During Reset 1 IRQA Input Input External Interrupt Request A--The IRQA input is a synchronized external interrupt request that indicates that an external device is requesting service. It can be programmed to be level-sensitive or negative-edge- triggered. 1 RESET Input Input Reset--This input is a direct hardware reset on the processor. When RESET is asserted low, the DSP is initialized and placed in the Reset state. A Schmitt trigger input is used for noise immunity. When the RESET pin is deasserted, the initial chip operating mode is latched from the EXTBOOT pin. The internal reset signal will be deasserted synchronous with the internal clocks, after a fixed number of internal clocks. Signal Description To ensure complete hardware reset, RESET and TRST should be asserted together. The only exception occurs in a debugging environment when a hardware DSP reset is required and it is necessary not to reset the OnCE/JTAG module. In this case, assert RESET, but do not assert TRST. 2.5 Pulse Width Modulator (PWM) Signals Table 8. Pulse Width Modulator (PWMA) Signals 8 No. of Pins Signal Name Signal Type State During Reset 6 PWMA0-5 Output Tri- stated 1 FAULTA0 Input Input Signal Description PWMA0-5-- These are six PWMA output pins. FAULTA0-- This fault input pin is used for disabling selected PWMA outputs in cases where fault conditions originate off chip. DSP56F801 Preliminary Technical Data MOTOROLA Serial Peripheral Interface (SPI) Signals 2.6 Serial Peripheral Interface (SPI) Signals Table 9. Serial Peripheral Interface (SPI) Signals No. of Pins Signal Name Signal Type State During Reset 1 MISO Input/ Output Input SPI Master In/Slave Out (MISO)--This serial data pin is an input to a master device and an output from a slave device. The MISO line of a slave device is placed in the highimpedance state if the slave device is not selected. GPIOB6 Input/ Output Input Port E GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. Signal Description After reset, the default state is MISO. 1 MOSI Input/ Output Input SPI Master Out/Slave In (MOSI)--This serial data pin is an output from a master device and an input to a slave device. The master device places data on the MOSI line a half-cycle before the clock edge that the slave device uses to latch the data. GPIOB5 Input/ Output Input Port E GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. After reset, the default state is MOSI. 1 SCLK Input/ Output Input SPI Serial Clock--In master mode, this pin serves as an output, clocking slaved listeners. In slave mode, this pin serves as the data clock input. GPIOB4 Input/ Output Input Port E GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. After reset, the default state is SCLK. SS Input Input SPI Slave Select--In master mode, this pin is used to arbitrate multiple masters. In slave mode, this pin is used to select the slave. GPIOB7 Input/ Output Input Port E GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. 1 After reset, the default state is SS. MOTOROLA DSP56F801 Preliminary Technical Data 9 2.7 Serial Communications Interface (SCI) Signals Table 10. Serial Communications Interface (SCI0) Signals No. of Pins Signal Name Signal Type State During Reset 1 TXD0 Output Input Transmit Data (TXD0)--transmit data output GPIOB0 Input/ Output Input Port B GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. Signal Description After reset, the default state is SCI output. 1 RXD0 Input Input Receive Data (RXD0)--receive data input GPIOB1 Input/ Output Input Port B GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as an input or output pin. After reset, the default state is SCI input. 2.8 Analog-to-Digital Converter (ADC) Signals Table 11. Analog to Digital Converter Signals No. of Pins Signal Name Signal Type State During Reset 4 ANA0-3 Input Input ANA0-3--Analog inputs to ADC channel 1 4 ANA4-7 Input Input ANA4-7--Analog inputs to ADC channel 2 1 VREF Input Input VREF--Analog reference voltage for ADC. Must be set to VDDA-0.3V for optimal performance. Signal Description 2.9 Quad Timer Module Signals Table 12. Quad Timer Module Signals No. of Pins Signal Name Signal Type State During Reset 3 TD0-2 Input/ Output Input TD0-2--Timer D Channel 0-2 GPIOA0-2 Input/ Output Input Port A GPIO--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. Signal Description After reset, the default state is the quad timer input. 10 DSP56F801 Preliminary Technical Data MOTOROLA JTAG/OnCE 2.10 JTAG/OnCE Table 13. JTAG/On-Chip Emulation (OnCE) Signals No. of Pins Signal Name Signal Type 1 TCK Input Input, pulled Test Clock Input--This input pin provides a gated clock to low internally synchronize the test logic and shift serial data to the JTAG/OnCE port. The pin is connected internally to a pull-down resistor. 1 TMS Input Input, pulled Test Mode Select Input--This input pin is used to sequence the JTAG high internally TAP controller's state machine. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. 1 TDI Input Input, pulled Test Data Input--This input pin provides a serial input data stream to high internally the JTAG/OnCE port. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. 1 TDO Output 1 TRST Input 1 DE Output MOTOROLA State During Reset Tri-stated Signal Description Test Data Output--This tri-statable output pin provides a serial output data stream from the JTAG/OnCE port. It is driven in the Shift-IR and Shift-DR controller states, and changes on the falling edge of TCK. Input, pulled Test Reset--As an input, a low signal on this pin provides a reset high internally signal to the JTAG TAP controller. To ensure complete hardware reset, TRST should be asserted whenever RESET is asserted. The only exception occurs in a debugging environment when a hardware DSP reset is required and it is necessary not to reset the OnCE/JTAG module. In this case, assert RESET, but do not assert TRST. Output Debug Event--DE provides a low pulse on recognized debug events. DSP56F801 Preliminary Technical Data 11 Part 3 Specifications 3.1 General Characteristics The DSP56F801 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The term "5-volt tolerant" refers to the capability of an I/O pin, built on a 3.3V compatible process technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5Vcompatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V 10% during normal operation without causing damage). This 5V tolerant capability therefore offers the power savings of 3.3V I/O levels while being able to receive 5V levels without being damaged. Absolute maximum ratings given in Table 14 are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent damage to the device. The DSP56F801 DC and AC electrical specifications are preliminary and are from design simulations. These specifications may not be fully tested or guaranteed at this early stage of the product life cycle. Finalized specifications will be published after complete characterization and device qualifications have been completed. CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Table 14. Absolute Maximum Ratings Characteristic Symbol Min Max Unit Supply voltage VDD VSS - 0.3 VSS + 4.0 V All other input voltages, excluding Analog inputs VIN VSS - 0.3 VSS + 5.5V V Analog inputs ANA0-7 and VREF VIN VSSA- 0.3 VDDA+ 0.3 V Analog inputs EXTAL, XTAL VIN VSSA- 0.3 VSSA+ 3.0 V Current drain per pin excluding VDD, VSS, & PWM ouputs I -- 10 mA Current drain per pin for PWM outputs I -- 20 mA TJ -- 150 C TSTG -55 150 C Junction temperature Storage temperature range 12 DSP56F801 Preliminary Technical Data MOTOROLA DC Electrical Characteristics Table 15. Recommended Operating Conditions Characteristic Supply voltage Symbol Min Max Unit VDD,VDDA 3.0 3.6 V TA -40 85 C Ambient operating temperature Table 16. Thermal Characteristics 1 48-pin LQFP Characteristic Symbol Value Unit Thermal resistance junction-to-ambient (estimated) JA 46.8 C/W I/O pin power dissipation PI/O User Determined W Power dissipation PD PD = (IDD x VDD) + PI/O W PDMAX (TJ - TA) / JA C Maximum allowed PD 1. See Section 5.1 for more detail. 3.2 DC Electrical Characteristics Table 17. DC Electrical Characteristics Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fop = 80 MHz Characteristic Symbol Min Typ Max Unit Input high voltage (XTAL/EXTAL) VIHC 2.25 2.5 2.75 V Input low voltage (XTAL/EXTAL) VILC 0 -- 0.5 V Input high voltage VIH 2.0 -- 5.5 V Input low voltage VIL -0.3 -- 0.8 V Input current low (pullups/pulldowns disabled) IIL -1 -- 1 A Input current high (pullups/pulldowns disabled) IIH -1 -- 1 A RPU, RPD -- 30 -- K Input/output tri-state current low IOZL -10 -- 10 A Input/output tri-state current low IOZH -10 -- 10 A Output High Voltage (at IOH) VOH VDD - 0.7 -- -- V Output Low Voltage (at IOL) VOL -- -- 0.4 V Output High Current IOH -- -- -4 mA Output Low Current IOL -- -- 4 mA Typical Pullup or pulldown resistance MOTOROLA DSP56F801 Preliminary Technical Data 13 Table 17. DC Electrical Characteristics (Continued) Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fop = 80 MHz Characteristic Symbol Min Typ Max Unit CIN -- 8 -- pF Output capacitance COUT -- 12 -- pF PWM pin output source current1 IOHP -- -- -10 mA PWM pin output sink current2 IOLP -- -- 16 mA VDD supply current IDDT3 Run 4 -- 103 138 mA Wait5 -- 72 98 mA Stop -- 71 97 mA VEI 2.4 2.7 2.9 V VPOR -- 1.7 2.0 V Input capacitance Low Voltage Interrupt6 Power on Reset7 1. PWM pin output source current measured with 50% duty cycle. 2. PWM pin output sink current measured with 50% duty cycle. 3. IDDT = IDD + IDDA (Total supply current for VDD + VDDA) 4. Run (operating) IDD measured using 8MHz clock source. All inputs 0.2V from rail; outputs unloaded. All ports configured as inputs; measured with all modules enabled. 5. Wait IDD measured using external square wave clock source (fosc = 8 MHz) into XTAL; all inputs 0.2V from rail; no DC loads; less than 50 pF on all outputs. CL = 20 pF on EXTAL; all ports configured as inputs; EXTAL capacitance linearly affects wait IDD; measured with PLL enabled. 6. Low voltage interrupt monitors the VDD supply. When VDD drops below VEI value, an interrupt is generated. Functionality of the device is guaranteed under transient conditions when V DDA>VEI. 7. Power-on reset occurs whenever the internally regulated 2.5V digital supply drops below 1.5V typical. While power is ramping up, this signal remains active for as long as the internal 2.5V is below 1.5V typical no matter how long the ramp up rate is. The internally regulated voltage is typically 100 mV less than V DD during ramp up until 2.5V is reached, at which time it self regulates. 14 DSP56F801 Preliminary Technical Data MOTOROLA AC Electrical Characteristics Digital (VDD=3.6V) Total Analog (VDDA=3.6V) 180 150 120 Idd (mA) 90 60 30 0 0 40 20 60 80 Freq. (MHz) Figure 3. Maximum Run IDD vs. Frequency (see Note 4 above) 3.3 AC Electrical Characteristics Timing waveforms in Section 3.3 are tested with a VIL maximum of 0.8V and a VIH minimum of 2.0V for all pins except XTAL, which is tested using the input levels in Section 3.2. In Figure 4 the levels of VIH and VIL for an input signal are shown. VIH Input Signal Low High 90% 50% 10% Midpoint1 VIL Fall Time Rise Time Note: The midpoint is VIL + (VIH - VIL)/2. Figure 4. Input Signal Measurement References Figure 5 shows the definitions of the following signal states: * Active state, when a bus or signal is driven, and enters a low impedance state. * Tri-stated, when a bus or signal is placed in a high impedance state. * Data Valid state, when a signal level has reached V OL or VOH. * Data Invalid state, when a signal level is in transition between VOL and VOH. MOTOROLA DSP56F801 Preliminary Technical Data 15 Data2 Valid Data1 Valid Data3 Valid Data2 Data1 Data3 Data Tri-stated Data Invalid State Data Active Data Active Figure 5. Signal States 3.4 Flash Memory Characteristics Table 18. Flash Memory Truth Table Mode XE1 YE2 SE3 OE4 PROG5 ERASE6 MAS17 NVSTR8 Standby L L L L L L L L Read H H H H L L L L Word Program H H L L H L L H Page Erase H L L L L H L H Mass Erase H L L L L H H H 1. 2. 3. 4. 5. 6. 7. 8. X address enable, all rows are disabled when XE = 0 Y address enable, YMUX is disabled when YE = 0 Sense amplifier enable Output enable, tri-state flash data out bus when OE = 0 Defines program cycle Defines erase cycle Defines mass erase cycle, erase whole block Defines non-volatile store cycle Table 19. IFREN Truth Table 16 Mode IFREN = 1 IFREN = 0 Read Read information block Read main memory block Word program Program information block Program main memory block Page erase Erase information block Erase main memory block Mass erase Erase both block Erase main memory block DSP56F801 Preliminary Technical Data MOTOROLA Flash Memory Characteristics Table 20. Timing Symbols Characteristic Symbol See Figure(s) PROG/ERASE to NVSTR set up time Tnvs Figure 6, Figure 7, Figure 8 NVSTR hold time Tnvh Figure 6, Figure 7 NVSTR hold time(mass erase) Tnvh1 Figure 8 NVSTR to program set up time Tpgs Figure 6 Program hold time Tpgh Figure 6 Address/data set up time Tads Figure 6 Address/data hold time Tadh Figure 6 Recovery time Trcv Figure 6, Figure 7, Figure 8 Cumulative program HV period Thv Figure 6 Program time Tprog Figure 6 Erase time Terase Figure 7 Mass erase time Tme Figure 8 Table 21. Flash Timing Parameters Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF Characteristic Symbol Min Typ Max Unit Program time Tprog 20 - - us Erase time Terase 20 - - ms Mass erase time Tme 100 - - ms Endurance1 ECYC 10,000 20,000 - cycles Data Retention1 @ 5000 cycles DRET 10 30 - years PROG/ERASE to NVSTR set up time Tnvs - 5 - us The following parameters should only be used in the Manual Word Programming Mode NVSTR hold time Tnvh - 5 - us NVSTR hold time (mass erase) Tnvh1 - 100 - us NVSTR to program set up time Tpgs - 10 - us MOTOROLA DSP56F801 Preliminary Technical Data 17 Table 21. Flash Timing Parameters (Continued) Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF Characteristic Symbol Min Typ Max Unit Recovery time Trcv - 1 - us Cumulative program HV period2 Thv - 3 - ms 1. Program specification guaranteed from TA = 0 C to 85 C. 2. Thv is the cumulative high voltage programming time to the same row before next erase. The same address cannot be programmed twice before next erase. IFREN XADR XE Tadh YADR YE DIN Tads PROG Tnvs Tprog Tpgh NVSTR Tpgs Tnvh Trcv Thv Figure 6. Flash Program Cycle 18 DSP56F801 Preliminary Technical Data MOTOROLA Flash Memory Characteristics IFREN XADR XE YE=SE=OE=MAS1=0 ERASE Tnvs NVSTR Tnvh Trcv Terase Figure 7. Flash Erase Cycle IFREN XADR XE MAS1 YE=SE=OE=0 ERASE Tnvs NVSTR Tnvh1 Tme Trcv Figure 8. Flash Mass Erase Cycle MOTOROLA DSP56F801 Preliminary Technical Data 19 3.5 External Clock Operation The DSP56F801 device clock is derived from either 1) an internal crystal oscillator circuit working in conjunction with an external crystal, 2) an external frequency source, or 3) an on-chip relaxation oscillator. To generate a reference frequency using the internal crystal oscillator circuit, a reference crystal external to the chip must be connected between the EXTAL and XTAL pins. Paragrahs 3.5.1 and 3.5.4 describe these methods of clocking. Whichever type of clock derivation is used provides a reference signal to a phaselocked loop (PLL) within the DSP56F801. In turn, the PLL generates a master reference frequency that determines the speed at which chip operations occur. Application code can be set to change the frequency source between the relaxation oscillator and crystal oscillator or external source, and power down the relaxation oscillator if desired. Selection of which clock is used is determined by setting the PRECS bit in the PLLCR (phase-locked loop control register) word (bit 2). If the bit is set to 1, the external crystal oscillator circuit is selected. If the bit is set to 0, the internal relaxation oscillator is selected, and this is the default value of the bit when power is first applied. 3.5.1 Crystal Oscillator The internal crystal oscillator circuit is designed to interface with a parallel-resonant crystal resonator in the frequency range specified for the external crystal, which is 4-8+ MHz. Figure 9 shows a typical crystal oscillator circuit. Follow the crystal supplier's recommendations when selecting a crystal, since crystal parameters determine the component values required to provide maximum stability and reliable start-up. The crystal and associated components should be mounted as close as possible to the EXTAL and XTAL pins to minimize output distortion and start-up stabilization time. EXTAL XTAL Rz Sample External Crystal Parameters: Rz = 10 M fc = 4-8 MHz (optimized for 8 MHz) fc Figure 9. External Crystal Oscillator Circuit 3.5.2 Ceramic Resonator It is also possible to drive the internal oscillator with a ceramic resonator, assuming the overall system design can tolerate the reduced signal integrity. In Figure 10, a typical ceramic resonator circuit is shown. Refer to supplier's recommendations when selecting a ceramic resonator and associated components. The resonator and components should be mounted as close as possible to the EXTAL and XTAL pins. EXTAL XTAL Rz Sample Ceramic Resonator Parameters Rz = 10 M fc = 4-8 MHz (optimized for 8 MHz) fc Figure 10. Connecting a Ceramic Resonator 20 DSP56F801 Preliminary Technical Data MOTOROLA External Clock Operation 3.5.3 External Clock Source The recommended method of connecting an external clock is given in Figure 11. The external clock source is connected to XTAL and the EXTAL pin is grounded. DSP56F801 XTAL EXTAL External Clock VSS Figure 11. Connecting an External Clock Signal Table 22. External Clock Operation Timing Requirements5 Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C Characteristic Symbol Min Typ Max Unit Frequency of operation (external clock driver)1 fosc 0 8 110 MHz Clock Pulse Width2, 5 tPW 6.25 -- -- ns External clock input rise time3, 5 trise -- -- 3 ns External clock input fall time4, 5 tfall -- -- 3 ns 1. 2. 3. 4. 5. See Figure 11 for details on using the recommended connection of an external clock driver. The high or low pulse width must be no smaller than 6.25 ns or the chip will not function. External clock input rise time is measured from 10% to 90%. External clock input fall time is measured from 90% to 10%. Parameters listed are guaranteed by design. VIH External Clock 90% 50% 10% 90% 50% 10% tPW tPW VIL tfall trise Note: The midpoint is VIL + (VIH - VIL)/2. Figure 12. External Clock Timing MOTOROLA DSP56F801 Preliminary Technical Data 21 3.5.4 Use of On-Chip Relaxation Oscillator Table 23. PLL Timing Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C Characteristic Symbol Min Typ Max Unit External reference crystal frequency for the PLL1 fosc 6 8 10 MHz PLL output frequency2 (Fout/2) fop 40 -- 80 MHz PLL stabilization time 3 0o to +85oC tplls -- 10 -- ms PLL stabilization time3 -40o to 0oC tplls -- 100 200 ms 1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly. The PLL is optimized for 8 MHz input crystal. 2. ZCLK may not exceed 80 MHz. For additional information on ZCLK and Fout/2, please refer to the OCCS chapter in the User Manual. 3. This is the minimum time required after the PLL setup is changed to ensure reliable operation. An internal relaxation oscillator can supply the reference frequency when an external frequency source or crystal are not used. During a DSP56F801 boot or reset sequence, the relaxation oscillator is enabled by default, and the PRECS bit in the PLLCR word is set to 0 (Section 3.5). If an external oscillator is connected, the relaxation oscillator can be deselected instead by setting the PRECS bit in the PLLCR to 1. When this occurs, the PRECSS bit in the PLLSR (prescaler clock select status register) data word also sets to 1. If a changeover between internal and external oscillators is required at startup, internal device circuits compensate for any asynchronous transitions between the two clock signals so that no glitches occur in the resulting master clock to the chip. When changing clocks, the user must ensure that the clock source is not switched until the desired clock is enabled and stable. To compensate for variances in the device manufacturing process, the accuracy of the relaxation oscillator can be incrementally adjusted to within 0.25% of 8 MHz by trimming an internal capacitor. Bits 0-7 of the IOSCTL (internal oscillator control) word allow the user to set in an additional offset (trim) to this preset value to increase or decrease capacitance. The default value of this trim is 128 units, making the power-up default capacitor size 432 units. Each unit added or deleted changes the output frequency by about 0.23%, allowing incremental adjustment until the desired frequency accuracy is achieved. Table 24. Relaxation Oscillator Characteristics Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C Characteristic Symbol Min Typ Max Unit Frequency Accuracy1 f -- +2 +5 % Frequency Drift over Temp fT 7 8 9 MHz Frequency Drift over Supply f/t -- +0.1 -- %/oC Trim Range f/t -- 0.1 -- %/V fT -- +0.25 -- % Trim Accuracy 1. 22 Over full temperature range. DSP56F801 Preliminary Technical Data MOTOROLA External Clock Operation 8.2 Output Frequency 8.1 8.0 7.9 7.8 7.7 7.6 -40 -25 -5 15 35 55 75 85 Temperature (oC) Figure 13. Typical Relaxation Oscillator Frequency vs. Temperature (Trimmed to 8MHz @ 25oC) 11 10 9 8 7 6 5 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Figure 14. Typical Relaxation Oscillator Frequency vs. Trim Value @ 25oC MOTOROLA DSP56F801 Preliminary Technical Data 23 3.6 Reset, Stop, Wait, Mode Select, and Interrupt Timing Table 25. Reset, Stop, Wait, Mode Select, and Interrupt Timing1, 5 Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF Characteristic Symbol Typical Min Typical Max Unit See RESET Assertion to Address, Data and Control Signals High Impedance tRAZ -- 21 ns Figure 15 Minimum RESET Assertion Duration2 OMR Bit 6 = 0 OMR Bit 6 = 1 tRA 275,000T 128T -- -- ns ns RESET De-assertion to First External Address Output tRDA 33T 34T ns Figure 15 Edge-sensitive Interrupt Request Width tIRW 1.5T -- ns Figure 16 IRQA, IRQB Assertion to External Data Memory Access Out Valid, caused by first instruction execution in the interrupt service routine tIDM -- 15T ns Figure 17 IRQA, IRQB Assertion to General Purpose Output Valid, caused by first instruction execution in the interrupt service routine tIG -- 16T ns Figure 17 IRQA Low to First Valid Interrupt Vector Address Out recovery from Wait State3 tIRI -- 13T ns Figure 18 IRQA Width Assertion to Recover from Stop State4 tIW -- 2T ns Figure 19 Delay from IRQA Assertion to Fetch of first instruction (exiting Stop) OMR Bit 6 = 0 OMR Bit 6 = 1 tIF Figure 15 Figure 19 -- -- Duration for Level Sensitive IRQA Assertion to Cause the Fetch of First IRQA Interrupt Instruction (exiting Stop) OMR Bit 6 = 0 OMR Bit 6 = 1 tIRQ Delay from Level Sensitive IRQA Assertion to First Interrupt Vector Address Out Valid (exiting Stop) OMR Bit 6 = 0 OMR Bit 6 = 1 tII 275,000T 12T ns ns Figure 20 -- -- 275,000T 12T ns ns Figure 20 -- -- 275,000T 12T ns ns 1. 2. In the formulas, T = clock cycle. For an operating frequency of 80 MHz, T = 12.5 ns. Circuit stabilization delay is required during reset when using an external clock or crystal oscillator in two cases: * After power-on reset * When recovering from Stop state 3. The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is not the minimum required so that the IRQA interrupt is accepted. 4. The interrupt instruction fetch is visible on the pins only in Mode 3. 5. Parameters listed are guaranteed by design. 24 DSP56F801 Preliminary Technical Data MOTOROLA Reset, Stop, Wait, Mode Select, and Interrupt Timing RESET tRA tRAZ tRDA A0-A15, D0-D15 First Fetch PS, DS, RD, WR First Fetch Figure 15. Asynchronous Reset Timing IRQA, IRQB tIRW Figure 16. External Interrupt Timing (Negative-Edge-Sensitive) A0-A15, PS, DS, RD, WR First Interrupt Instruction Execution tIDM IRQA, IRQB a) First Interrupt Instruction Execution General Purpose I/O Pin tIG IRQA, IRQB b) General Purpose I/O Figure 17. External Level-Sensitive Interrupt Timing MOTOROLA DSP56F801 Preliminary Technical Data 25 IRQA, IRQB tIRI A0-A15, PS, DS, RD, WR First Interrupt Vector Instruction Fetch Figure 18. Interrupt from Wait State Timing tIW IRQA tIF A0-A15, PS, DS, RD, WR First Instruction Fetch Not IRQA Interrupt Vector Figure 19. Recovery from Stop State Using Asynchronous Interrupt Timing tIRQ IRQA tII A0-A15 PS, DS, RD, WR First IRQA Interrupt Instruction Fetch Figure 20. Recovery from Stop State Using IRQA Interrupt Service 26 DSP56F801 Preliminary Technical Data MOTOROLA Serial Peripheral Interface (SPI) Timing 3.7 Serial Peripheral Interface (SPI) Timing Table 26. SPI Timing1 Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fOP = 80MHz Characteristic Symbol Cycle time Master Slave Max Unit 50 25 -- -- ns ns -- 25 -- -- ns ns -- 100 -- -- ns ns 17.6 12.5 -- -- ns ns 24.1 25 -- -- ns ns 20 0 -- -- ns ns 0 2 -- -- ns ns 4.8 15 ns 3.7 15.2 ns -- -- 4.5 20.4 ns ns 0 0 -- -- ns ns -- -- 11.5 10.0 ns ns -- -- 9.7 9.0 ns ns tC Enable lead time Master Slave tELD Enable lag time Master Slave tELG Clock (SCK) high time Master Slave tCH Clock (SCK) low time Master Slave tCL Data setup time required for inputs Master Slave tDS Data hold time required for inputs Master Slave tDH Access time (time to data active from highimpedance state) Slave tA Disable time (hold time to high-impedance state) Slave tD Data Valid for outputs Master Slave (after enable edge) tDV Data invalid Master Slave tDI Rise time Master Slave tR Fall time Master Slave tF 1. Parameters Min See Figure Figures 21, 22, 23, 24 Figure 24 Figure 24 Figures 21, 22, 23, 24 Figures 21, 22, 23, 24 Figures 21, 22, 23, 24 Figures 21, 22, 23, 24 Figure 24 Figure 24 Figures 21, 22, 23, 24 Figures 21, 22, 23, 24 Figures 21, 22, 23, 24 Figures 21, 22, 23, 24 listed are guaranteed by design. MOTOROLA DSP56F801 Preliminary Technical Data 27 SS SS is held High on master (Input) tC tR tF tCL SCLK (CPOL = 0) (Output) tF tCH tR tCL SCLK (CPOL = 1) (Output) tDH tCH tDS MISO (Input) MSB in Bits 14-1 tDI MOSI (Output) LSB in tDI(ref) tDV Master MSB out Bits 14-1 Master LSB out tF tR Figure 21. SPI Master Timing (CPHA = 0) SS SS is held High on master (Input) tF tC tR tCL SCLK (CPOL = 0) (Output) tCH tF tCL SCLK (CPOL = 1) (Output) tCH MISO (Input) MSB in tDI tDV(ref) MOSI (Output) Master MSB out tDS tR tDH Bits 14-1 LSB in tDV Bits 14- 1 tF Master LSB out tR Figure 22. SPI Master Timing (CPHA = 1) 28 DSP56F801 Preliminary Technical Data MOTOROLA Serial Peripheral Interface (SPI) Timing SS (Input) tC tF tCL SCLK (CPOL = 0) (Input) tELG tR tCH tELD tCL SCLK (CPOL = 1) (Input) tCH tA MISO (Output) Slave MSB out tDS tR tF tD Bits 14-1 Slave LSB out tDV tDI tDI tDH MOSI (Input) MSB in Bits 14-1 LSB in Figure 23. SPI Slave Timing (CPHA = 0) SS (Input) tC tF tCL SCLK (CPOL = 0) (Input) tCH tELG tELD SCLK (CPOL = 1) (Input) tR tDV tCL tR tCH tA MISO (Output) Slave MSB out Bits 14-1 tDV tDS tDH MOSI (Input) MSB in tD tF Bits 14-1 Slave LSB out tDI LSB in Figure 24. SPI Slave Timing (CPHA = 1) MOTOROLA DSP56F801 Preliminary Technical Data 29 3.8 Quad Timer Timing Table 27. Timer Timing1, 2 Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fOP = 80 MHz Characteristic Symbol Typical Min Typical Max Unit PIN 4T+6 -- ns Timer input high/low period PINHL 2T+3 -- ns Timer output period POUT 2T -- ns POUTHL 1T -- ns Timer input period Timer output high/low period 1. 2. In the formulas listed, T = clock cycle. For 80 MHz operation, T = 12.5 ns. Parameters listed are guaranteed by design. Timer Inputs PIN PINHL PINHL POUTHL POUTHL Timer Outputs POUT Figure 25. Timer Timing 3.9 Serial Communication Interface (SCI) Timing Table 28. SCI Timing Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fOP = 80 MHz Characteristic Symbol Min Max Unit BR -- (fMAX*2.5)/(80) Mbps RXD2 Pulse Width RXDPW 0.965/BR 1.04/BR ns TXD3 Pulse Width TXDPW 0.965/BR 1.04/BR ns Baud Rate1 1. 2. 3. 4. 30 fMAX is the frequency of operation of the system clock in MHz. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1. Parameters listed are guaranteed by design. DSP56F801 Preliminary Technical Data MOTOROLA Analog-to-Digital Converter (ADC) Characteristics RXD SCI receive data pin (Input) RXDPW Figure 26. RXD Pulse Width TXD SCI receive data pin (Input) TXDPW Figure 27. TXD Pulse Width 3.10 Analog-to-Digital Converter (ADC) Characteristics Table 29. ADC Characteristics Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, VREF = VDD-0.3V, ADCDIV = 4, 9, or 14, ADC clock = 4MHz, 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fOP = 80 MHz Characteristic Symbol Min Typ Max Unit VADIN 0 -- VDDA1 V Resolution RES 12 -- 12 Bits Integral Non-Linearity2 INL -- +/- 4 +/- 5 LSB3 Differential Non-Linearity DNL -- +/- 0.9 +/- 1 LSB3 Input voltages Monotonicity GUARANTEED ADC internal clock fADIC 0.5 -- 5 MHz Conversion range RAD VSSA -- VDDA V Conversion time tADC -- 6 -- tAIC cycles4 Sample time tADS -- 1 -- tAIC cycles4 Input capacitance CADI -- 5 -- pF4 Gain Error (transfer gain) EGAIN 1.00 1.10 1.15 -- VOFFSET +10 +230 +325 mV THD 55 60 -- dB Signal-to-Noise plus Distortion SINAD 54 56 -- dB Effective Number of Bits ENOB 8.5 9.5 -- bit Spurious Free Dynamic Range SFDR 60 65 -- dB Offset Voltage Total Harmonic Distortion MOTOROLA DSP56F801 Preliminary Technical Data 31 Table 29. ADC Characteristics (Continued) Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, VREF = VDD-0.3V, ADCDIV = 4, 9, or 14, ADC clock = 4MHz, 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fOP = 80 MHz Characteristic Symbol Min Typ Max Unit Bandwidth BW -- 100 -- KHz ADC Quiescent Current (both ADCs) IADC -- 39.3 -- mA VREF Quiescent Current (both ADCs) IVREF -- 11.85 14.5 mA 1. VDDA should be tied to the same potential as VDD via separate traces. VREF must be equal to or less than VDD and must be greater than or equal to 2.7V. 2. Measured in 10-90% range. 3. LSB = Least Significant Bit. ADC analog input 1 3 2 4 Figure 28. Equivalent Analog Input Circuit 1. 2. 3. Parasitic capacitance due to package, pin to pin, and pin to package base coupling. 1.8pf Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing. 2.04pf Equivalent resistance for the ESD isolation resistor and the channel select mux. 500 ohms Sampling capacitor at the sample and hold circuit. Capacitor 4 is normally disconnected from the input and is only connected to it at sampling time. 1pf 32 DSP56F801 Preliminary Technical Data MOTOROLA JTAG Timing 3.11 JTAG Timing Table 30. JTAG Timing 1, 3 Operating Conditions: VSS = VSSA = 0 V, VDD = VDDA = 3.0-3.6 V, TA = -40 to +85C, CL 50 pF, fOP = 80 MHz Characteristic Symbol Min Max Unit TCK frequency of operation2 fOP DC 10 MHz TCK cycle time tCY 100 -- ns TCK clock pulse width tPW 50 -- ns TMS, TDI data setup time tDS 0.4 -- ns TMS, TDI data hold time tDH 1.2 -- ns TCK low to TDO data valid tDV -- 26.6 ns TCK low to TDO tri-state tTS -- 23.5 ns tTRST 50 -- ns tDE 8T -- ns TRST assertion time DE assertion time 1. Timing is both wait state and frequency dependent. For the values listed, T = clock cycle. For 80 MHz operation, T = 12.5 ns. 2. TCK frequency of operation must be less than 1/8 the processor rate. 3. Parameters listed are guaranteed by design. tCY tPW tPW VIH VM TCK (Input) VM = VIL + (VIH - VIL)/2 VM VIL Figure 29. Test Clock Input Timing Diagram MOTOROLA DSP56F801 Preliminary Technical Data 33 TCK (Input) tDS TDI TMS (Input) tDH Input Data Valid tDV TDO (Output) Output Data Valid tTS TDO (Output) tDV TDO (Output) Output Data Valid Figure 30. Test Access Port Timing Diagram TRST (Input) tTRST Figure 31. TRST Timing Diagram DE tDE Figure 32. OnCE--Debug Event 34 DSP56F801 Preliminary Technical Data MOTOROLA Package and Pin-Out Information DSP56F801 Part 4 Packaging 4.1 Package and Pin-Out Information DSP56F801 ANA5 ANA6 ORIENTATION MARK TDO ANA4 37 TD1 TD2 ANA7 PWMA0 VCAPC1 VDD VSS PWMA1 PWMA2 PWMA3 PWMA4 PWMA5 This section contains package and pin-out information for the 48-pin LQFP configuration of the DSP56F801. ANA3 VREF PIN 1 /SS ANA2 Motorola MISO ANA1 MOSI ANA0 SCLK FAULTA0 DSP56F801 TXDO VSS VSS VDD VDD VSSA 25 RXD0 VDDA 13 TRST TDO XTAL EXTAL VDD VSS VCAPC2 TDI IREQA TMS TCK RESET TCS DE Figure 33. Top View, DSP56F801 48-pin LQFP Package MOTOROLA DSP56F801 Preliminary Technical Data 35 Table 31. DSP56F801 Pin Identification by Pin Number Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TD0 13 TCS 25 RESET 37 ANA5 2 TD1 14 TCK 26 VDDA 38 ANA6 3 TD2 15 TMS 27 VSSA 39 ANA7 4 SS 16 IREQA 28 VDD 40 PWMA0 5 MISO 17 TDI 29 VSS 41 VCAPC1 6 MOSI 18 VCAPC2 30 FAULTA0 42 VDD 7 SCLK 19 VSS 31 ANA0 43 VSS 8 TXD0 20 VDD 32 ANA1 44 PWMA1 9 VSS 21 EXTAL 33 ANA2 45 PWMA2 10 VDD 22 XTAL 34 VREF 46 PWMA3 11 RXD0 23 TDO 35 ANA3 47 PWMA4 12 DE 24 TRST 36 ANA4 48 PWMA5 36 DSP56F801 Preliminary Technical Data MOTOROLA Package and Pin-Out Information DSP56F801 4X 9 DETAIL Y A P A1 48 37 1 36 T U B V AE B1 12 25 13 AE V1 24 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE AB IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS T, U, AND Z TO BE DETERMINED AT DATUM PLANE AB. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE AC. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE AB. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.350. 8. MINIMUM SOLDER PLATE THICKNESS SHALL BE 0.0076. Z S1 DIM A A1 B B1 C D E F G H J K L M N P R S S1 V V1 W AA T, U, Z S DETAIL Y 4X 0.200 AC T-U Z 0.080 AC G AB AD AC M BASE METAL TOP & BOTTOM R J 0.250 N MILLIMETERS MIN MAX 7.000 BSC 3.500 BSC 7.000 BSC 3.500 BSC 1.400 1.600 0.170 0.270 1.350 1.450 0.170 0.230 0.500 BSC 0.050 0.150 0.090 0.200 0.500 0.700 0 7 12 REF 0.090 0.160 0.250 BSC 0.150 0.250 9.000 BSC 4.500 BSC 9.000 BSC 4.500 BSC 0.200 REF 1.000 REF C E GAUGE PLANE 0.200 AB T-U Z F D 0.080 M AC T-U Z SECTION AE-AE H CASE 932-03 ISSUE F W L K DETAIL AD AA Figure 34. 48-pin LQFP Mechanical Information MOTOROLA DSP56F801 Preliminary Technical Data 37 Part 5 Design Considerations 5.1 Thermal Design Considerations An estimation of the chip junction temperature, TJ, in C can be obtained from the equation: Equation 1: TJ = T A + ( P D x R JA ) Where: TA = ambient temperature C RJA = package junction-to-ambient thermal resistance C/W PD = power dissipation in package Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and a case-to-ambient thermal resistance: Equation 2: RJA = RJC + R CA Where: RJA = package junction-to-ambient thermal resistance C/W RJC = package junction-to-case thermal resistance C/W RCA = package case-to-ambient thermal resistance C/W RJC is device-related and cannot be influenced by the user. The user controls the thermal environment to change the case-to-ambient thermal resistance, RCA. For example, the user can change the air flow around the device, add a heat sink, change the mounting arrangement on the Printed Circuit Board (PCB), or otherwise change the thermal dissipation capability of the area surrounding the device on the PCB. This model is most useful for ceramic packages with heat sinks; some 90% of the heat flow is dissipated through the case to the heat sink and out to the ambient environment. For ceramic packages, in situations where the heat flow is split between a path to the case and an alternate path through the PCB, analysis of the device thermal performance may need the additional modeling capability of a system level thermal simulation tool. The thermal performance of plastic packages is more dependent on the temperature of the PCB to which the package is mounted. Again, if the estimations obtained from RJA do not satisfactorily answer whether the thermal performance is adequate, a system level model may be appropriate. Definitions: A complicating factor is the existence of three common definitions for determining the junction-to-case thermal resistance in plastic packages: 38 * Measure the thermal resistance from the junction to the outside surface of the package (case) closest to the chip mounting area when that surface has a proper heat sink. This is done to minimize temperature variation across the surface. * Measure the thermal resistance from the junction to where the leads are attached to the case. This definition is approximately equal to a junction to board thermal resistance. DSP56F801 Preliminary Technical Data MOTOROLA Electrical Design Considerations * Use the value obtained by the equation (TJ - TT)/PD where TT is the temperature of the package case determined by a thermocouple. The junction-to-case thermal resistances quoted in this data sheet are determined using the first definition on page 45. From a practical standpoint, that value is also suitable for determining the junction temperature from a case thermocouple reading in forced convection environments. In natural convection, using the junction-to-case thermal resistance to estimate junction temperature from a thermocouple reading on the case of the package will estimate a junction temperature slightly hotter than actual. Hence, the new thermal metric, Thermal Characterization Parameter, or JT, has been defined to be (TJ - TT)/PD. This value gives a better estimate of the junction temperature in natural convection when using the surface temperature of the package. Remember that surface temperature readings of packages are subject to significant errors caused by inadequate attachment of the sensor to the surface and to errors caused by heat loss to the sensor. The recommended technique is to attach a 40-gauge thermocouple wire and bead to the top center of the package with thermally conductive epoxy. 5.2 Electrical Design Considerations CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Use the following list of considerations to assure correct DSP operation: * Provide a low-impedance path from the board power supply to each VDD pin on the DSP, and from the board ground to each VSS (GND) pin. * The minimum bypass requirement is to place six 0.01-0.1 F capacitors positioned as close as possible to the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the ten VDD/VSS pairs, including VDDA/VSSA. The VCAP capacitors must be 150 milliohm or less ESR capacitors. * Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND) pins are less than 0.5 inch per capacitor lead. * Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and VSS. * Bypass the VDD and VSS layers of the PCB with approximately 100 F, preferably with a highgrade capacitor such as a tantalum capacitor. * Because the DSP output signals have fast rise and fall times, PCB trace lengths should be minimal. * Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance. This is especially critical in systems with higher capacitive loads that could create higher transient currents in the VDD and GND circuits. MOTOROLA DSP56F801 Preliminary Technical Data 39 * Take special care to minimize noise levels on the VREF, VDDA and VSSA pins. * Designs that utilize the TRST pin for JTAG port or OnCE module functionality (such as development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as well as a means to assert TRST independently of RESET. Designs that do not require debugging functionality, such as consumer products, should tie these pins together. * Because the Flash memory is programmed through the JTAG/OnCE port, designers should provide an interface to this port to allow in-circuit Flash programming. Part 6 Ordering Information Table 32 lists the pertinent information needed to place an order. Consult a Motorola Semiconductor sales office or authorized distributor to determine availability and to order parts. Table 32. DSP56F801 Ordering Information Part Supply Voltage DSP56F801 3.0-3.6 V Package Type Low Profile Plastic Quad Flat Pack (LQFP) Pin Count Frequency (MHz) Order Number 48 80 DSP56F801FA80 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and the Stylized M Logo are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. (c) Motorola, Inc. 2002. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu. Minato-ku, Tokyo 106-8573 Japan. 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 852-26668334 Technical Information Center: 1-800-521-6274 HOME PAGE: http://www.motorola.com/semiconductors/ DSP56F801/D