STF201-22 & STF201-30 USB Downstream Port Filter & TVS For EMI Filtering and ESD Protection PROTECTION PRODUCTS Description Features The STF201 is a combination EMI filter and line termination device with integrated TVS diodes for use on downstream USB ports. It is constructed using a proprietary technology that allows passive components and TVS diodes to be integrated in the same package. Each device will provide termination, filtering, and ESD protection for one downstream USB port. The STF201 is an easily implemented solution for meeting the requirements of revision 1.1 of the Universal Serial Bus specification. USB line termination is achieved with series 22 or 30 resistors on both the D+ and D- USB lines. These resistors preserve signal integrity by matching the cable impedance to that of the differential driver. The 15k pull-down resistors complete the termination circuit on each line. They are required by the USB specification to identify the line as a downstream connection. The 47pF capacitors are used to bypass high frequency energy to ground and for edge rate control of the USB signals. Finally, the STF201 contains TVS diodes for ESD protection of both (D+ & D-) data lines and the voltage bus (VBUS). The TVS diodes provide effective suppression of ESD voltages in excess of 15kV (air discharge) and 8kV (contact discharge) per IEC 610004-2, level 4. The small size and integrated feature of the STF201 minimizes required board space and increases system reliability. The pin-out of the device allows easy implementation. The STF201 is suitable for use in USB hubs, computers, peripherals, and portable devices. Bidirectional EMI/RFI filtering and line termination with integrated ESD protection ESD protection for USB power (VBUS) and data lines (D+ & D-) to IEC 61000-4-2 Level 4 Filtering and termination for two USB data lines Different series resistors for impedance matching Low TVS operating voltage (5.25V) Low leakage current Low capacitance Solid-state technology Mechanical Characteristics EIAJ SOT23-6L package Molding compound flammability rating: UL 94V-0 Marking : Marking Code Packaging : Tape and Reel per EIA 481 Applications Circuit Diagram USB Hubs Portable electronics Printers Monitors Servers, Desktop, and Notebook computers Pin Configuration S0T23-6L (Top View) Revision 08/11/04 1 www.semtech.com STF201-22 & STF201-30 PROTECTION PRODUCTS Absolute Maximum Rating Rating Symbol Value Units Steady-State Power Ppk 100 mW ESD Air Discharge per IEC 61000-4-2 ESD Contact Discharge per IEC 61000-4-2 VESD 15 8 kV Lead Soldering Temperature TL 260 (10 sec.) C Operating Temperature TJ -40 to +125 C TSTG -55 to +150 C Storage Temperature Electrical Characteristics STF201-xx Parameter Symbol Conditions Minimum Typical Maximum Units 5 .2 5 V T VS Reverse Stand-Of f Voltage VRWM T VS Reverse Breakdown Voltage VBR It = 1mA T VS Reverse Leakage Current IR VRWM = 5.25V, T=25C Between VBUS pin and Ground 5 A T VS Reverse Leakage Current IR VRWM = 3.3V, T=25C Between any data (D+, D-) pin and Ground. 1 A T VS Junction Capacitance Cj Between I/O pins and Ground, each device VR = 0V, f = 1MHz Series Resistance (STF201-22) RS Each Line 20 22 24 Series Resistance (STF201-30) RS Each Line 27 30 33 Pulldown Resistance RPD Each Line 1 3 .5 15 16.5 k C Each Line 47 pF CTOT Between Input or Output to Ground VR = 0V, f = 1MHz 60 pF Capacitor Total Capacitance 2004 Semtech Corp. 2 6 V 10 pF www.semtech.com STF201-22 & STF201-30 PROTECTION PRODUCTS Typical Characteristics ESD Clamping (8kV Contact) ESD Clamping (15kV Air) Typical Insertion Loss Analog Crosstalk (D+ to D-) 0 dB 0 dB -20 dB -10 dB -60 dB -20 dB 0.030MHz 2004 Semtech Corp. 0.030 MHz 2.0GHz 3 1 GHz www.semtech.com STF201-22 & STF201-30 PROTECTION PRODUCTS Applications Information Figure 1 - STF201 Functional Circuit Diagram Device Connection The STF201 is designed to provide termination, EMI filtering and ESD protection for two USB I/O lines. The equivalent circuit diagram is shown in Figure 1. The device is connected as follows: z USB data lines are routed through the STF201 for easy implementation and optimum pc board layout. Pin 1 is connected to the voltage supply line. The input of the D+ line is routed into pin 2 and out of pin 5. The input of the D- line is connected at pin 3 and the output at pin 4. Pin 6 is connected to ground. The ground connection should be made directly to the ground plane for best results. The path length is kept as short as possible to reduce the effects of parasitic inductance in the board traces. Figure 2 - STF201 Connection Diagram USB Port Design Considerations The Universal Serial Bus (USB) specification requires termination and filtering components for proper operation. In addition, an open USB socket is vulnerable to hazardous ESD discharges in excess of 15kV. These discharges can occur on the data lines or the voltage bus. The STF201 is an easily implemented solution designed to meet the termination & EMI filter requirements of the USB specification revision 1.1. It also provides ESD protection to IEC 61000-4-2, level 4. 6 2 5 3 4 tion, bidirectional EMI filtering, and ESD protection on downstream (STF201) or upstream (STF202) ports. The SC5826 is a dual port power switch that provides individual or ganged port switching, fault reporting, and inrush current limiting as required by the USB specification. The SC5205 ULDO provides a stable voltage to the USB controller. Board Placement & layout Guidelines. A simplified USB port is shown in Figure 3. USB line termination is achieved with series resistors on both the D+ and D- lines. These resistors preserve signal integrity by matching the cable impedance to that of the differential driver. 15k pull-down resistors are used to identify a downstream port while an upstream port is identified with a 1.5K pull up resistor on either the D+ (full speed devices) or the D- (low speed devices) data line. Capacitors are used to bypass high frequency energy to ground and for edge rate control of the USB signals. TVS diodes are added for ESD protection of both (D+ & D-) data lines and the voltage bus (VBUS). A power distribution switch and voltage regulator provide the power management functions of the port. Board layout and placement of the STF201 play a critical role in EMI & ESD suppression. Designing a USB hub to meet EMI & ESD immunity requirements requires a combination of optimum component placement, trace routing, and good circuit design practices. Some general guidelines are given below: z z z z z Semtech provides a complete solution to simplify USB port design (Figure 4). The STF201 & STF202 integrate all of the components necessary for line termina 2004 Semtech Corp. 1 4 Avoid running D+ & D- signal line traces near high speed clock lines or similar signal lines. Avoid running critical signal lines near board edges. Locate the USB controller chip physically near the USB connectors. Place the STF201 near the USB connector to restrict transient coupling. Minimize the path length between the USB connector and the STF201 as well as between the USB controller and the STF201. www.semtech.com STF201-22 & STF201-30 PROTECTION PRODUCTS Applications Information Figure 3 - USB Port Components Figure 4 - Typical USB Hub Design 2004 Semtech Corp. 5 www.semtech.com STF201-22 & STF201-30 PROTECTION PRODUCTS Outline Drawing A e1 2X E/2 D DIM N EI 1 H H E ccc C 2X N/2 TIPS c GAGE PLANE 2 A A1 A2 b c D E1 E e e1 L L1 N 01 aaa bbb ccc 0.25 L e 01 (L1) B DETAIL A D aaa C A2 SEATING PLANE C A SEE DETAIL A1 bxN bbb A DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .057 .035 .000 .006 .035 .045 .051 .010 .020 .003 .009 .110 .114 .118 .060 .063 .069 .110 BSC .037 BSC .075 BSC .012 .018 .024 (.024) 6 0 10 .004 .008 .008 1.45 0.90 0.00 0.15 .90 1.15 1.30 0.25 0.50 0.08 0.22 2.80 2.90 3.00 1.50 1.60 1.75 2.80 BSC 0.95 BSC 1.90 BSC 0.30 0.45 0.60 (0.60) 6 0 10 0.10 0.20 0.20 SIDE VIEW C A-B D NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. Land Pattern - X DIM (C) G C G P X Y Z Z Y DIMENSIONS MILLIMETERS INCHES (.098) .055 .037 .024 .043 .141 (2.50) 1.40 0.95 0.60 1.10 3.60 P NOTES: 1. 2004 Semtech Corp. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 6 www.semtech.com STF201-22 & STF201-30 PROTECTION PRODUCTS Marking Codes Part Number Marking Code STF201-22 122 STF201-30 130 Ordering Information Part Number Lead Finish Qty per Reel R eel Size STF201-22.TC SnPb 3,000 7 Inch STF201-30.TC SnPb 3,000 7 Inch STF201-22.TCT Pb free 3,000 7 Inch STF201-30.TCT Pb free 3,000 7 Inch Contact Information Semtech Corporation Protection Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 2004 Semtech Corp. 7 www.semtech.com