( )
OUT ADJ
R
V = 1.25 V I R
R2
2
1
1
æ ö
+ +
ç ÷
è ø
LM317-N
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator
1 Features 3 Description
The LM117 and LM317-N series of adjustable 3-pin
1• Typ. 0.1% Load Regulation positive voltage regulators are capable of supplying in
• Typ. 0.01%/V Line Regulation excess of 1.5 A over a 1.25-V to 37-V output range
• 1.5-A Output Current and a wide temperature range. They are
exceptionally easy to use and require only two
• Adjustable Output Down to 1.25 V external resistors to set the output voltage. Further,
• Current Limit Constant With Temperature both line and load regulation are better than standard
• 80-dB Ripple Rejection fixed regulators.
• Short-Circuit Protected Output The LM117 and LM317-N offer full overload
•−55°C to 150°C Operating Temperature Range protection such as current limit, thermal overload
(LM117) protection and safe area protection. All overload
protection circuitry remains fully functional even if the
adjustment terminal is disconnected.
2 Applications
• Automotive LED Lighting Typically, no capacitors are needed unless the device
is situated more than 6 inches from the input filter
• Battery Chargers capacitors, in which case an input bypass is needed.
• Post Regulation for Switching Supplies An optional output capacitor can be added to improve
• Constant Current Regulators transient response. The adjustment terminal can be
bypassed to achieve very high ripple rejection ratios
• Microprocessor Supplies that are difficult to achieve with standard 3-terminal
regulators.
Typical Application Because the regulator is floating and detects only the
input-to-output differential voltage, supplies of several
hundred volts can be regulated as long as the
maximum input-to-output differential is not exceeded.
That is, avoid short-circuiting the output.
By connecting a fixed resistor between the
adjustment pin and output, the LM117 and LM317-N
can be also used as a precision current regulator.
Supplies with electronic shutdown can be achieved
by clamping the adjustment terminal to ground, which
programs the output to 1.25 V where most loads draw
little current.
For applications requiring greater output current, see
data sheets for LM150 series (3 A), SNVS772, and
LM138 series (5 A), SNVS771. For the negative
complement, see LM137 (SNVS778) series data
*Needed if device is more than 6 inches from filter sheet.
capacitors.
†Optional—improves transient response Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
TO-3 (2) 38.94 mm x 25.40 mm
†† LM117 TO (3) 8.255 mm × 8.255 mm
TO-3 (2) 38.94 mm x 25.40 mm
TO-220 (3) 14.986 mm × 10.16 mm
TO-263 (3) 10.18 mm × 8.41 mm
LM317-N SOT-223 (4) 6.50 mm × 3.50 mm
TO (3) 8.255 mm × 8.255 mm
TO-252 (3) 6.58 mm × 6.10 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Table of Contents
8.3 Feature Description................................................. 13
1 Features.................................................................. 18.4 Device Functional Modes........................................ 13
2 Applications ........................................................... 19 Application and Implementation ........................ 15
3 Description............................................................. 19.1 Application Information............................................ 15
4 Revision History..................................................... 29.2 Typical Applications ................................................ 15
5 Device Comparison Table..................................... 310 Power Supply Recommendations ..................... 27
6 Pin Configuration and Functions......................... 311 Layout................................................................... 27
7 Specifications......................................................... 511.1 Layout Guidelines ................................................. 27
7.1 Absolute Maximum Ratings ...................................... 511.2 Layout Example .................................................... 27
7.2 ESD Ratings.............................................................. 511.3 Thermal Considerations........................................ 28
7.3 Recommended Operating Conditions....................... 512 Device and Documentation Support ................. 35
7.4 Thermal Information, LM117..................................... 512.1 Documentation Support ........................................ 35
7.5 Thermal Information, LM317-N................................. 612.2 Related Links ........................................................ 35
7.6 LM117 Electrical Characteristics............................... 612.3 Community Resources.......................................... 35
7.7 LM317-N Electrical Characteristics........................... 712.4 Trademarks........................................................... 35
7.8 Typical Characteristics.............................................. 812.5 Electrostatic Discharge Caution............................ 35
8 Detailed Description............................................ 11 12.6 Glossary................................................................ 35
8.1 Overview................................................................. 11 13 Mechanical, Packaging, and Orderable
8.2 Functional Block Diagram....................................... 12 Information ........................................................... 35
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision O (January 2014) to Revision P Page
• Added, updated, or renamed the following sections: Description;Pin Configuration and Functions;Specifications;
ESD Ratings table; Application and Implementation;Power Supply Recommendations;Layout;Mechanical,
Packaging, and Ordering Information .................................................................................................................................... 1
• Removed information regarding LM317A, formerly part of this data sheet. LM317A can now be found in the TI
catalog under literature number SNVSAC2 ........................................................................................................................... 1
Changes from Revision N (August 2013) to Revision O Page
• Deleted MDT Package (over Full Operating Temperature Range) ....................................................................................... 7
• Changed Current Limit MIN from 0.112 to 0.15 and TYP from 0.3 to 0.4 for (VIN – VOUT) = 40 V in the LM317A
and LM317-N Electrical Characteristics Section .................................................................................................................... 7
• Deleted MDT Package ........................................................................................................................................................... 7
2Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
5 Device Comparison Table
Table 1. LM317 Family Options
PART NUMBER TEMPERATURE DESCRIPTION PRODUCT FOLDER
LM317-N 0°C to 125°C 40-V, 1.5-A Catalog device Click here
LM317A −40°C to 125°C 40-V, 1.5-A Industrial device Click here
LM317HV 0°C to 125°C 60-V, 1.5-A Catalog device Click here
LM317L-N −40°C to 125°C 40-V, 0.1-A, Industrial device Click here
LM117 −55°C to 150°C 40-V, 1.5-A Extended-temperature device Click here
LM117HV −55°C to 150°C 60-V, 1.5-A Extended-temperature device Click here
LM117HVQML −55°C to 125°C 60-V, 1.5-A Military-grade device per spec MIL-PRF-38535 Click here
LM117HVQML-SP −55°C to 125°C 60-V, 1.5-A Space-grade device Click here
LM117JAN −55°C to 125°C 40-V, 1.5-A Military-grade device per spec MIL-PRF-38510 Click here
LM117QML −55°C to 125°C 40-V, 1.5-A Military-grade device per spec MIL-PRF-38535 Click here
LM117QML-SP −55°C to 125°C 40-V, 1.5-A Space-grade device Click here
6 Pin Configuration and Functions
NDS Metal Can Package NDT Metal Can Package
2-Pin TO-3 3-Pin TO
Bottom View Bottom View
Case is Output
Case is Output
Pin Functions, Metal Can Packages
PIN I/O DESCRIPTION
NAME TO-3 TO
ADJ 1 2 — Adjust pin
VOUT CASE 3, CASE O Output voltage pin for the regulator
VIN 2 1 I Input voltage pin for the regulator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
KTT Surface-Mount Package DCY Surface-Mount Package
3-Pin DDPAK/TO-263 4-Pin SOT-223
Top View Top View
NDP Surface-Mount Package
NDE Plastic Package 3-Pin TO-252
3-Pin TO-220 Front View
Front View
Pin Functions
PIN I/O DESCRIPTION
NAME TO-263 TO-220 SOT-223 TO-252
ADJ 1 1 1 1 — Adjust pin
VOUT 2, TAB 2, TAB 2, 4 2, TAB O Output voltage pin for the regulator
VIN 3 3 3 3 I Input voltage pin for the regulator
4Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)
MIN MAX UNIT
Power dissipation Internally Limited
Input-output voltage differential −0.3 40 V
Metal package (soldering, 10 seconds) 300 °C
Lead temperature Plastic package (soldering, 4 seconds) 260 °C
Storage temperature, Tstg −65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
7.2 ESD Ratings VALUE UNIT
Electrostatic
V(ESD) Human-body model (HBM)(1) ±3000 V
discharge
(1) Manufacturing with less than 500-V HBM is possible with the necessary precautions. Pins listed as ±3000 V may actually have higher
performance.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
Operating temperature (LM117) −55 150 °C
Operating temperature (LM317-N) 0 125 °C
7.4 Thermal Information, LM117 LM117
NDS NDT
THERMAL METRIC(1) UNIT
(TO-3) (TO)
2 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance(2) 39 186 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 2 21 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) No heatsink.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
7.5 Thermal Information, LM317-N LM317-N
KTT NDE DCY NDT NDP
THERMAL METRIC(1)(2) UNIT
(TO-263) (TO-220) (SOT-223) (TO) (TO-252)
3 PINS 3 PINS 4 PINS 3 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance 41.0 23.3 59.6 186(3) 54 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 43.6 16.2 39.3 21 51.3 °C/W
RθJB Junction-to-board thermal resistance 23.6 4.9 8.4 — 28.6 °C/W
ψJT Junction-to-top characterization parameter 10.4 2.7 1.8 — 3.9 °C/W
ψJB Junction-to-board characterization parameter 22.6 4.9 8.3 — 28.1 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 0.9 1.1 — — 0.9 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) When surface mount packages are used (SOT-223, TO-252), the junction to ambient thermal resistance can be reduced by increasing
the PCB copper area that is thermally connected to the package. See Heatsink Requirements for heatsink techniques.
(3) No heatsink
7.6 LM117 Electrical Characteristics
Some specifications apply over full Operating Temperature Range as noted. Unless otherwise specified, TJ= 25°C, VIN −
VOUT = 5 V, and IOUT = 10 mA.(1)(2)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
3 V ≤(VIN −VOUT)≤40 V,
Reference voltage 1.2 1.25 1.3 V
10 mA ≤IOUT ≤IMAX(1) (over full operating temperature range)
TJ= 25°C 0.01 0.02
Line regulation 3 V ≤(VIN −VOUT)≤40 V(3) %/V
over full operating 0.02 0.05
temperature range
TJ= 25°C 0.1% 0.3%
Load regulation 10 mA ≤IOUT ≤IMAX(1)(3) over full operating 0.3% 1%
temperature range
Thermal regulation 20-ms pulse 0.03 0.07 %/W
Adjustment pin current over full operating temperature range 50 100 μA
10 mA ≤IOUT ≤IMAX(1)
Adjustment pin current change 0.2 5 μA
3 V ≤(VIN −VOUT)≤40 V (over full operating temperature range)
Temperature stability TMIN ≤TJ≤TMAX (over full operating temperature range) 1%
Minimum load current (VIN −VOUT) = 40 V (over full operating temperature range) 3.5 5 mA
TO-3 Package (over full 1.5 2.2 3.4
operating temperature range)
(VIN −VOUT)≤15 V A
TO-39 Package (over full 0.5 0.8 1.8
Current limit operating temperature range)
TO-3 package 0.3 0.4
(VIN −VOUT) = 40 V A
TO-39 package 0.15 0.2
RMS output noise, % of VOUT 10 Hz ≤f≤10 kHz 0.003%
VOUT = 10 V, f = 120 Hz, CADJ = 0 μF (over full operating 65 dB
temperature range)
Ripple rejection ratio VOUT = 10 V, f = 120 Hz, CADJ = 10 μF (over full operating 66 80 dB
temperature range)
Long-term stability TJ= 125°C, 1000 hrs 0.3% 1%
(1) IMAX = 1.5 A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0 A for the DCY (SOT-223) package.
IMAX = 0.5 A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA),
device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any
temperature is : PD(MAX) = ((TJ(MAX) – TA) / θJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL).
(2) Specifications and availability for military and space grades of LM117/883 can be found in the LM117QML data sheet (SNVS356).
Specifications and availability for military and space grades of LM117 can be found in the LM117JAN data sheet (SNVS365).
(3) Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specifications for thermal regulation.
6Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
7.7 LM317-N Electrical Characteristics(1)
Some specifications apply over full Operating Temperature Range as noted. Unless otherwise specified, TJ= 25°C, VIN −
VOUT = 5 V, and IOUT = 10 mA.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TJ= 25°C 1.25 V
3 V ≤(VIN −VOUT)≤40 V,
Reference voltage 10 mA ≤IOUT ≤IMAX(1) (over Full Operating Temperature 1.2 1.25 1.3 V
Range) TJ= 25°C 0.01 0.04
Line regulation 3V ≤(VIN −VOUT)≤40 V(2) %/V
(over full operating 0.02 0.07
temperature range)
TJ= 25°C 0.1% 0.5%
Load regulation 10 mA ≤IOUT ≤IMAX(1)(2) (over full operating 0.3% 1.5%
temperature range)
Thermal regulation 20-ms pulse 0.04 0.07 %/W
Adjustment pin current (over full operating temperature range) 50 100 μA
10 mA ≤IOUT ≤IMAX(1) (over full operating
Adjustment pin current change 0.2 5 μA
3V ≤(VIN −VOUT)≤40V temperature range)
(over full operating
Temperature stability TMIN ≤TJ≤TMAX 1%
temperature range)
(over full operating
Minimum load current (VIN −VOUT) = 40 V 3.5 10 mA
temperature range)
TO-3, TO-263 Packages
(over full operating 1.5 2.2 3.4
temperature range)
SOT-223, TO-220
Packages (over full
(VIN −VOUT)≤15 V 1.5 2.2 3.4 A
operating temperature
range)
Current limit TO, TO-252 Package (over
full operating temperature 0.5 0.8 1.8
range)
TO-3, TO-263 packages 0.15 0.4
(VIN −VOUT) = 40 V SOT-223, TO-220 packages 0.15 0.4 A
TO, TO-252 package 0.075 0.2
RMS output noise, % of VOUT 10 Hz ≤f≤10 kHz 0.003%
VOUT = 10 V, f = 120 Hz, CADJ = 0 μF (over full operating 65 dB
temperature range)
Ripple rejection ratio VOUT = 10V, f = 120 Hz, CADJ = 10 μF (over full operating 66 80 dB
temperature range)
Long-term stability TJ= 125°C, 1000 hrs 0.3% 1%
(1) IMAX = 1.5 A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0 A for the DCY (SOT-223) package.
IMAX = 0.5 A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA),
device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any
temperature is : PD(MAX) = ((TJ(MAX) – TA) / θJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL).
(2) Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specifications for thermal regulation.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
7.8 Typical Characteristics
Output Capacitor = 0 μF, unless otherwise noted.
Figure 1. Load Regulation Figure 2. Current Limit
Figure 4. Dropout Voltage
Figure 3. Adjustment Current
Figure 5. VOUT vs VIN, VOUT = VREF Figure 6. VOUT vs VIN, VOUT = 5 V
8Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Typical Characteristics (continued)
Output Capacitor = 0 μF, unless otherwise noted.
Figure 7. Temperature Stability Figure 8. Minimum Operating Current
Figure 9. Ripple Rejection Figure 10. Ripple Rejection
Figure 12. Output Impedance
Figure 11. Ripple Rejection
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Characteristics (continued)
Output Capacitor = 0 μF, unless otherwise noted.
Figure 13. Line Transient Response Figure 14. Load Transient Response
10 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM317-N
( )
OUT ADJ
R
V = 1.25 V I R
R2
2
1
1
æ ö
+ +
ç ÷
è ø
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
8 Detailed Description
8.1 Overview
In operation, the LM317-N develops a nominal 1.25-V reference voltage, VREF, between the output and
adjustment terminal. The reference voltage is impressed across program resistor R1 and, because the voltage is
constant, a constant current I1then flows through the output set resistor R2, giving an output voltage calculated
by Equation 1:
(1)
Figure 15. Setting the VOUT Voltage
Because the 100-μA current from the adjustment terminal represents an error term, the LM317-N was designed
to minimize IADJ and make it very constant with line and load changes. To do this, all quiescent operating current
is returned to the output establishing a minimum load current requirement. If there is insufficient load on the
output, the output will rise.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM117 LM317-N
LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
8.3 Feature Description
8.3.1 Load Regulation
The LM317-N is capable of providing extremely good load regulation but a few precautions are needed to obtain
maximum performance. The current set resistor, R1, must be connected near the output terminal of the regulator
rather than near the load. If R1 is placed too far from the output terminal, then the increased trace resistance, RS,
will cause an error voltage drop in the adjustment loop and degrade load regulation performance. Therefore, R1
must be placed as close as possible to the output terminal to minimize RSand maximize load regulation
performance.
Figure 16 shows the effect of the trace resistance, RS, when R1 is placed far from the output terminal of the
regulator. It is clear that RSwill cause an error voltage drop especially during higher current loads, so it is
important to minimize the RStrace resistance by keeping R1 close to the regulator output terminal.
Figure 16. Regulator With Line Resistance in Output Lead
With the TO-3 package, it is easy to minimize the resistance from the case to the set resistor, by using two
separate leads to the case. However, with the TO package, care must be taken to minimize the wire length of the
output lead. The ground of R2 can be returned near the ground of the load to provide remote ground sensing
and improve load regulation.
8.4 Device Functional Modes
8.4.1 External Capacitors
An input bypass capacitor is recommended. A 0.1-μF disc or 1-μF solid tantalum on the input is suitable input
bypassing for almost all applications. The device is more sensitive to the absence of input bypassing when
adjustment or output capacitors are used, but the above values will eliminate the possibility of problems.
The adjustment terminal can be bypassed to ground on the LM317-N to improve ripple rejection. This bypass
capacitor prevents ripple from being amplified as the output voltage is increased. With a 10-μF bypass capacitor,
80-dB ripple rejection is obtainable at any output level. Increases over 10 μF do not appreciably improve the
ripple rejection at frequencies above 120 Hz. If the bypass capacitor is used, it is sometimes necessary to
include protection diodes to prevent the capacitor from discharging through internal low current paths and
damaging the device.
In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance
even at high frequencies. Depending upon capacitor construction, it takes about 25 μF in aluminum electrolytic to
equal 1-μF solid tantalum at high frequencies. Ceramic capacitors are also good at high frequencies. However,
some types have a large decrease in capacitance at frequencies around 0.5 MHz. For this reason, 0.01-μF disc
may seem to work better than a 0.1-μF disc as a bypass.
Although the LM317-N is stable with no output capacitors, like any feedback circuit, certain values of external
capacitance can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1-μF solid
tantalum (or 25-μF aluminum electrolytic) on the output swamps this effect and insures stability. Any increase of
the load capacitance larger than 10 μF will merely improve the loop stability and output impedance.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM117 LM317-N
( )
OUT ADJ
R
V = 1.25 V I R
R2
2
1
1
æ ö
+ +
ç ÷
è ø
LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Device Functional Modes (continued)
8.4.2 Protection Diodes
When external capacitors are used with any IC regulator, it is sometimes necessary to add protection diodes to
prevent the capacitors from discharging through low current points into the regulator. Most 10-μF capacitors have
low enough internal series resistance to deliver 20-A spikes when shorted. Although the surge is short, there is
enough energy to damage parts of the IC.
When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge
into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage
of the regulator, and the rate of decrease of VIN. In the LM317-N, this discharge path is through a large junction
that is able to sustain 15-A surge with no problem. This is not true of other types of positive regulators. For
output capacitors of 25 μF or less, there is no need to use diodes.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs
when either the input, or the output, is shorted. Internal to the LM317-N is a 50-Ωresistor which limits the peak
discharge current. No protection is needed for output voltages of 25 V or less and 10-μF capacitance. Figure 17
shows an LM317-N with protection diodes included for use with outputs greater than 25 V and high values of
output capacitance.
D1 protects against C1
D2 protects against C2
Figure 17. Regulator With Protection Diodes
14 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers must
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM117 and LM317-N are versatile, high performance, linear regulators with high accuracy and a wide
temperature range. An output capacitor can be added to further improve transient response, and the ADJ pin can
be bypassed to achieve very high ripple-rejection ratios. Its functionality can be utilized in many different
applications that require high performance regulation, such as battery chargers, constant current regulators, and
microprocessor supplies.
9.2 Typical Applications
9.2.1 1.25-V to 25-V Adjustable Regulator
The LM117 can be used as a simple, low-dropout regulator to enable a variety of output voltages needed for
demanding applications. By using an adjustable R2 resistor, a variety of output voltages can be made possible
as shown in Figure 18.
NOTE: Full output current not available at high input-output voltages
*Needed if device is more than 6 inches from filter capacitors.
†Optional—improves transient response. Output capacitors in the range of 1 μF to 1000 μF of aluminum or tantalum
electrolytic are commonly used to provide improved output impedance and rejection of transients.
Figure 18. 1.25-V to 25-V Adjustable Regulator
9.2.1.1 Design Requirements
The device component count is very minimal, employing two resistors as part of a voltage divider circuit and an
output capacitor for load regulation. An input capacitor is needed if the device is more than 6 inches from filter
capacitors. An optional bypass capacitor across R2 can also be used to improve PSRR.
9.2.1.2 Detailed Design Procedure
The output voltage is set based on the selection of the two resistors, R1 and R2, as shown in Figure 18. For
details on capacitor selection, refer to External Capacitors.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM117 LM317-N
LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
9.2.1.3 Application Curve
As shown in Figure 19, VOUT will rise with VIN minus some dropout voltage. This dropout voltage during startup
will vary with ROUT.
Figure 19. VOUT vs VIN, VOUT = 5V
9.2.2 5-V Logic Regulator With Electronic Shutdown
Figure 20 shows a variation of the 5-V output regulator application uses the L117 along with an NPN transistor to
provide shutdown control. The NPN will either block or sink the current from the ADJ pin by responding to the
TTL pin logic. When TTL is pulled high, the NPN is on and pulls the ADJ pin to GND, and the LM117 outputs
about
1.25 V. When TTL is pulled low, the NPN is off and the regulator outputs according to the programmed
adjustable voltage.
NOTE: Min. output ≊1.2 V
Figure 20. 5-V Logic Regulator With Electronic Shutdown
16 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Typical Applications (continued)
9.2.3 Slow Turnon 15-V Regulator
An application of LM117 includes a PNP transistor with a capacitor to implement slow turnon functionality (see
Figure 21). As VIN rises, the PNP sinks current from the ADJ rail. The output voltage at start up is the addition of
the 1.25-V reference plus the drop across the base to emitter. While this is happening, the capacitor begins to
charge and eventually opens the PNP. At this point, the device functions normally, regulating the output at 15 V.
A diode is placed between C1 and VOUT to provide a path for the capacitor to discharge. Such controlled turnon
is useful for limiting the in-rush current.
Figure 21. Slow Turnon 15-V Regulator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM117 LM317-N
R3
267
1%
R2
1.5 k
1%
R1
2 k
5%
C1
0.1 µF
LM329
VIN
15 V VOUT
10 V
VIN VOUT
LM117
ADJ
LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
9.2.4 Adjustable Regulator With Improved Ripple Rejection
To improve ripple rejection, a capacitor is used to bypass the ADJ pin to GND (see Figure 22). This is used to
smooth output ripple by cleaning the feedback path and stopping unnecessary noise from being fed back into the
device, propagating the noise.
NOTE: †Solid tantalum
*Discharges C1 if output is shorted to ground
Figure 22. Adjustable Regulator With Improved Ripple Rejection
9.2.5 High Stability 10-V Regulator
Using a high stability shunt voltage reference in the feedback path, such as the LM329, provides damping
necessary for a stable, low noise output (see Figure 23).
Figure 23. High Stability 10-V Regulator
18 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
three LM195 devices in parallel
LM117
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Typical Applications (continued)
9.2.6 High-Current Adjustable Regulator
Using the LM195 power transistor in parallel with the LM117 can increase the maximum possible output load
current (see Figure 24). Sense resistor R1 provides the 0.6 V across base to emitter to turn on the PNP. This on
switch allows current to flow, and the voltage drop across R3 drives three LM195 power transistors designed to
carry an excess of 1 A each.
NOTE
The selection of R1 determines a minimum load current for the PNP to turn on. The higher
the resistor value, the lower the load current must be before the transistors turn on.
NOTE: ‡Optional—improves ripple rejection
†Solid tantalum
*Minimum load current = 30 mA
Figure 24. High-Current Adjustable Regulator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM117 LM317-N
LM117
LM117
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
9.2.7 Emitter-Follower Current Amplifier
The LM117 is used as a constant current source in the emitter follower circuit (see Figure 25). The LM195 power
transistor is being used as a current gain amplifier, boosting the INPUT current. The LM117 provides a stable
current bias than just using a resistor.
Figure 25. Emitter-Follower Current Amplifier
9.2.8 1-A Current Regulator
A simple, fixed current regulator can be made by placing a resistor between the VOUT and ADJ pins of the LM117
(see Figure 26). By regulating a constant 1.25 V between these two terminals, a constant current is delivered to
the load.
Figure 26. 1-A Current Regulator
20 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Typical Applications (continued)
9.2.9 Common-Emitter Amplifier
Sometimes it is necessary to use a power transistor for high current gain. In this case, the LM117 provides
constant current at the collector of the LM195 in this common emitter application (see Figure 27). The 1.25-V
reference between VOUT and ADJ is maintained across the 2.4-Ωresistor, providing about 500-mA constant bias
current into the collector of the LM195.
Figure 27. Common-Emitter Amplifier
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM117 LM317-N
LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
9.2.10 Low-Cost 3-A Switching Regulator
The LM317-N can be used in a switching buck regulator application in cost sensitive applications that require
high efficiency. The switch node above D1 oscillates between ground and VIN, as the voltage across sense
resistor R1 drives the power transistor on and off. Figure 28 exhibits self-oscillating behavior by negative
feedback through R6 and C3 to the ADJ pin of the LM317-N.
NOTE: †Solid tantalum
*Core—Arnold A-254168-2 60 turns
Figure 28. Low-Cost 3-A Switching Regulator
22 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
mV
Short circuit current is approximately , or 210 mA
R
600
3
-
LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Typical Applications (continued)
9.2.11 Current-Limited Voltage Regulator
A maximum limit on output current can be set using the circuit shown in Figure 29. The load current travels
through R3 and R4. As the load current increases, the voltage drop across R3 increases until the NPN transistor
is driven, during which the ADJ pin is pulled down to ground and the output voltage is pulled down to the
reference voltage of 1.25 V.
(Compared to LM117's higher current limit)
—At 50 mA output only ¾ volt of drop occurs in R3and R4
Figure 29. Current-Limited Voltage Regulator
9.2.12 Adjusting Multiple On-Card Regulators With Single Control
Figure 30 shows how multiple LM117 regulators can be controlled by setting one resistor. Because each device
maintains the reference voltage of about 1.25 V between its VOUT and ADJ pins, we can connect each ADJ rail to
a single resistor, setting the same output voltage across all devices. This allows for independent outputs, each
responding to its corresponding input only. Designers must also consider that by the nature of the circuit,
changes to R1 and R2 will affect all regulators.
NOTE: *All outputs within ±100 mV
†Minimum load—10 mA
Figure 30. Adjusting Multiple On-Card Regulators With Single Control
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM117 LM317-N
LM317-N
LM317-N
LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
9.2.13 AC Voltage Regulator
In Figure 31, the top regulator is +6 V above the bottom regulator. It is clear that when the input rises above +6 V
plus the dropout voltage, only the top LM317-N regulates +6 V at the output. When the input falls below –6 V
minus the dropout voltage, only the bottom LM317-N regulates –6 V at the output. For regions where the output
is not clipped, there is no regulation taking place, so the output follows the input.
Figure 31. AC Voltage Regulator
9.2.14 12-V Battery Charger
The LM317-N can be used in a battery charger application shown in Figure 32, where the device maintains either
constant voltage or constant current mode depending on the current charge of the battery. To do this, the part
senses the voltage drop across the battery and delivers the maximum charging current necessary to charge the
battery. When the battery charge is low, there exists a voltage drop across the sense resistor RS, providing
constant current to the battery at that instant. As the battery approaches full charge, the potential drop across RS
approaches zero, reducing the current and maintaining the fixed voltage of the battery.
Use of RSallows low charging rates with fully charged battery.
Figure 32. 12-V Battery Charger
24 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM317-N
LM317-N
LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Typical Applications (continued)
9.2.15 Adjustable 4-A Regulator
Using three LM317-N devices in parallel increases load current capability (Figure 33). Output voltage is set by
the variable resistor tied to the non-inverting terminal of the operational amplifier, and reference current to the
transistor is developed across the 100 Ωresistor. When output voltage rises, the operational amplifier corrects by
drawing current from the base, closing the transistor. This effectively pulls ADJ down and lowers the output
voltage through negative feedback.
Figure 33. Adjustable 4-A Regulator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LM117 LM317-N
LM317-N
LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Typical Applications (continued)
9.2.16 Current-Limited 6-V Charger
The current in a battery charger application is limited by switching between constant current and constant voltage
states (see Figure 34). When the battery pulls low current, the drop across the 1 Ωresistor is not substantial and
the NPN remains off. A constant voltage is seen across the battery, as regulated by the resistor divider. When
current through the battery rises past peak current, the 1 Ωprovides enough voltage to turn the transistor on,
pulling ADJ close to ground. This results in limiting the maximum current to the battery.
*Sets peak current (0.6A for 1Ω)
**The 1000-μF is recommended to filter out input transients
Figure 34. Current-Limited 6-V Charger
9.2.17 Digitally Selected Outputs
Figure 35 demonstrates a digitally selectable output voltage. In its default state, all transistors are off and the
output voltage is set based on R1 and R2. By driving certain transistors, the associated resistor is connected in
parallel to R2, modifying the output voltage of the regulator.
*Sets maximum VOUT
Figure 35. Digitally Selected Outputs
(2)
26 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
10 Power Supply Recommendations
The input supply to the LM117 and LM317-N must be kept at a voltage level such that its maximum input to
output differential voltage is not exceeded. The minimum dropout voltage must also be met with extra headroom
when possible to keep the LM117 and LM317-N in regulation. An input capacitor is recommended, especially
when the input pin is located more than 6 inches away from the power supply source. For more information
regarding capacitor selection, refer to External Capacitors.
11 Layout
11.1 Layout Guidelines
Some layout guidelines must be followed to ensure proper regulation of the output voltage with minimum noise.
Traces carrying the load current must be wide to reduce the amount of parasitic trace inductance and the
feedback loop from VOUT to ADJ must be kept as short as possible. To improve PSRR, a bypass capacitor can
be placed at the ADJ pin and must be located as close as possible to the IC. In cases when VIN shorts to ground,
an external diode must be placed from VOUT to VIN to divert the surge current from the output capacitor and
protect the IC. Similarly, in cases when a large bypass capacitor is placed at the ADJ pin and VOUT shorts to
ground, an external diode must be placed from ADJ to VOUT to provide a path for the bypass capacitor to
discharge. These diodes must be placed close to the corresponding IC pins to increase their effectiveness.
11.2 Layout Example
Figure 36. Layout Example (SOT-223)
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Layout Example (continued)
Figure 37. Layout Example (TO-220)
11.3 Thermal Considerations
11.3.1 Heatsink Requirements
The LM317-N regulators have internal thermal shutdown to protect the device from over-heating. Under all
operating conditions, the junction temperature of the LM317-N must not exceed the rated maximum junction
temperature (TJ) of 150°C for the LM117, or 125°C for the LM317-N. A heatsink may be required depending on
the maximum device power dissipation and the maximum ambient temperature of the application. To determine if
a heatsink is needed, the power dissipated by the regulator, PD, must be calculate with Equation 3:
PD= ((VIN −VOUT) × IL) + (VIN × IG) (3)
Figure 38 shows the voltage and currents which are present in the circuit.
The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX) in Equation 4:
TR(MAX) = TJ(MAX) −TA(MAX) (4)
where TJ(MAX) is the maximum allowable junction temperature (150°C for the LM117, or 125°C for the LM317-N),
and TA(MAX) is the maximum ambient temperature that will be encountered in the application.
Using the calculated values for TR(MAX) and PD, the maximum allowable value for the junction-to-ambient thermal
resistance (θJA) can be calculated with Equation 5:
θJA = (TR(MAX) / PD) (5)
28 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Thermal Considerations (continued)
Figure 38. Power Dissipation Diagram
If the calculated maximum allowable thermal resistance is higher than the actual package rating, then no
additional work is needed. If the calculated maximum allowable thermal resistance is lower than the actual
package rating either the power dissipation (PD) needs to be reduced, the maximum ambient temperature TA(MAX)
needs to be reduced, the thermal resistance (θJA) must be lowered by adding a heatsink, or some combination of
these.
If a heatsink is needed, the value can be calculated from Equation 6:
θHA ≤(θJA – (θCH +θJC))
where
•θCH is the thermal resistance of the contact area between the device case and the heatsink surface
•θJC is thermal resistance from the junction of the die to surface of the package case (6)
When a value for θHA is found using the equation shown, a heatsink must be selected that has a value that is
less than, or equal to, this number.
The θHA rating is specified numerically by the heatsink manufacturer in the catalog, or shown in a curve that plots
temperature rise vs power dissipation for the heatsink.
11.3.2 Heatsinking Surface Mount Packages
The TO-263 (KTT), SOT-223 (DCY) and TO-252 (NDP) packages use a copper plane on the PCB and the PCB
itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the package to
the plane.
11.3.2.1 Heatsinking the SOT-223 (DCY) Package
Figure 39 and Figure 40 show the information for the SOT-223 package. Figure 40 assumes a θJA of 74°C/W for
1-oz. copper and 59.6°C/W for 2-oz. copper and a maximum junction temperature of 125°C. See AN-1028
(SNVA036) for thermal enhancement techniques to be used with SOT-223 and TO-252 packages.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Thermal Considerations (continued)
Figure 40. Maximum Power Dissipation vs TAMB for the
Figure 39. θJA vs Copper (2-oz.) Area for the SOT-223 SOT-223 Package
Package
11.3.2.2 Heatsinking the TO-263 (KTT) Package
Figure 41 shows for the TO-263 the measured values of θJA for different copper area sizes using a typical PCB
with 1-oz. copper and no solder mask over the copper area used for heatsinking.
As shown in Figure 41, increasing the copper area beyond 1 square inch produces very little improvement. It
must also be observed that the minimum value of θJA for the TO-263 package mounted to a PCB is 32°C/W.
Figure 41. θJA vs Copper (1-oz.) Area for the TO-263 Package
As a design aid, Figure 42 shows the maximum allowable power dissipation compared to ambient temperature
for the TO-263 device (assuming θJA is 35°C/W and the maximum junction temperature is 125°C).
30 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Thermal Considerations (continued)
Figure 42. Maximum Power Dissipation vs TAMB for the TO-263 Package
11.3.2.3 Heatsinking the TO-252 (NDP) Package
If the maximum allowable value for θJA is found to be ≥54°C/W (typical rated value) for the TO-252 package, no
heatsink is needed because the package alone will dissipate enough heat to satisfy these requirements. If the
calculated value for θJA falls below these limits, a heatsink is required.
As a design aid, Table 2 shows the value of the θJA of NDP the package for different heatsink area. The copper
patterns that we used to measure these θJAs are shown in Figure 47.Figure 43 reflects the same test results as
what are in Table 2.
Figure 44 shows the maximum allowable power dissipation versus ambient temperature for the TO-252 device.
Figure 45 shows the maximum allowable power dissipation versus copper area (in2) for the TO-252 device. See
AN-1028 (SNVA036) for thermal enhancement techniques to be used with SOT-223 and TO-252 packages.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 31
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
SNVS774P –MAY 2004–REVISED OCTOBER 2015
www.ti.com
Thermal Considerations (continued)
Table 2. θJA Different Heatsink Area
LAYOUT COPPER AREA THERMAL RESISTANCE
Top Side (in2)(1) Bottom Side (in2) (θJA°C/W) TO-252
1 0.0123 0 103
2 0.066 0 87
3 0.3 0 60
4 0.53 0 54
5 0.76 0 52
6 1.0 0 47
7 0.066 0.2 84
8 0.066 0.4 70
9 0.066 0.6 63
10 0.066 0.8 57
11 0.066 1.0 57
12 0.066 0.066 89
13 0.175 0.175 72
14 0.284 0.284 61
15 0.392 0.392 55
16 0.5 0.5 53
(1) Tab of device attached to topside of copper.
Figure 43. θJA vs 2-oz. Copper Area for TO-252 Figure 44. Maximum Allowable Power Dissipation vs
Ambient Temperature for TO-252
32 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
Figure 45. Maximum Allowable Power Dissipation vs 2-oz. Copper Area for TO-252
Figure 46. Top View of the Thermal Test Pattern in Actual Scale
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 33
Product Folder Links: LM117 LM317-N
LM117
,
LM317-N
www.ti.com
SNVS774P –MAY 2004–REVISED OCTOBER 2015
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
• For applications requiring greater output current, see LM150 series (3A) (SNVS772) and LM138 series (5A)
(SNVS771) data sheets.
• For the negative complement, see LM137 (SNVS778) series data sheet.
• For specifications and availability for military and space grades of LM117/883, see the LM117QML data sheet
(SNVS356).
• Specifications and availability for military and space grades of LM117JAN can be found in the LM117 data
sheet (SNVS365).
• For thermal enhancement techniques to be used with SOT-223 and TO-252 packages, see AN-1028,
Maximum Power Enhancement Techniques for Power Packages (SNVA036).
12.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY
LM117 Click here Click here Click here Click here Click here
LM317-N Click here Click here Click here Click here Click here
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 35
Product Folder Links: LM117 LM317-N
PACKAGE OPTION ADDENDUM
www.ti.com 30-Sep-2015
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM117H ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 150 ( LM117HP+ ~
LM117HP+)
LM117H/NOPB ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 150 ( LM117HP+ ~
LM117HP+)
LM117K STEEL ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI -55 to 150 LM117K
STEELP+
LM117K STEEL/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 150 LM117K
STEELP+
LM317EMP NRND SOT-223 DCY 4 1000 TBD Call TI Call TI 0 to 125 N01A
LM317EMP/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N01A
LM317EMPX/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N01A
LM317H ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM 0 to 125 ( LM317HP+ ~
LM317HP+)
LM317H/NOPB ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM 0 to 125 ( LM317HP+ ~
LM317HP+)
LM317K STEEL ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI 0 to 125 LM317K
STEELP+
LM317K STEEL/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM 0 to 125 LM317K
STEELP+
LM317MDT/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS
& no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 LM317
MDT
LM317MDTX/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS
& no Sb/Br) CU SN Level-2-260C-1 YEAR 0 to 125 LM317
MDT
LM317S/NOPB ACTIVE DDPAK/
TO-263 KTT 3 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM317S
P+
LM317SX/NOPB ACTIVE DDPAK/
TO-263 KTT 3 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM317S
P+
LM317T NRND TO-220 NDE 3 45 TBD Call TI Call TI LM317T P+
LM317T/LF01 ACTIVE TO-220 NDG 3 45 Pb-Free (RoHS
Exempt) CU SN Level-4-260C-72 HR LM317T P+
LM317T/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM317T P+
PACKAGE OPTION ADDENDUM
www.ti.com 30-Sep-2015
Addendum-Page 2
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM317EMP SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM317EMP/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM317EMPX/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM317MDTX/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2
LM317SX/NOPB DDPAK/
TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 30-Sep-2015
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM317EMP SOT-223 DCY 4 1000 367.0 367.0 35.0
LM317EMP/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0
LM317EMPX/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0
LM317MDTX/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0
LM317SX/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0
PACKAGE MATERIALS INFORMATION
www.ti.com 30-Sep-2015
Pack Materials-Page 2
MECHANICAL DATA
NDT0003A
www.ti.com
H03A (Rev D)
MECHANICAL DATA
NDS0002A
www.ti.com
MECHANICAL DATA
NDE0003B
www.ti.com
MECHANICAL DATA
NDG0003F
www.ti.com
T03F (Rev B)
MECHANICAL DATA
NDP0003B
www.ti.com
TD03B (Rev F)
MECHANICAL DATA
MPDS094A – APRIL 2001 – REVISED JUNE 2002
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE
4202506/B 06/2002
6,30 (0.248)
6,70 (0.264)
2,90 (0.114)
3,10 (0.122)
6,70 (0.264)
7,30 (0.287) 3,70 (0.146)
3,30 (0.130)
0,02 (0.0008)
0,10 (0.0040)
1,50 (0.059)
1,70 (0.067)
0,23 (0.009)
0,35 (0.014)
1 2 3
4
0,66 (0.026)
0,84 (0.033)
1,80 (0.071) MAX
Seating Plane
0°–10°
Gauge Plane
0,75 (0.030) MIN
0,25 (0.010)
0,08 (0.003)
0,10 (0.004) M
2,30 (0.091)
4,60 (0.181) M
0,10 (0.004)
NOTES: A. All linear dimensions are in millimeters (inches).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC TO-261 Variation AA.
MECHANICAL DATA
KTT0003B
www.ti.com
BOTTOM SIDE OF PACKAGE
TS3B (Rev F)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
