DIGITAL FIBER SENSOR FX-100SERIES Conforming to EMC Directive Bringing digital fiber sensors closer New possibilities with digital fiber sensors. The FX series is a round 100 for success. Easy to read, multipurpose, and at an economical price. The FX series has been designed to be what customers want it to be. Take a step into the new world that starts with `100'. Easy to read The digital dual-display shines out in the workplace! The digital dual-display allows you to check both the threshold value and incident light intensity at the same time, and it also makes the procedures for setting the various values much easier. The threshold values can be adjusted simply by pressing the (UP) key or the (DOWN) key, so that the sensors can be used at the same sensitivity levels as analog control-type sensors. And of course a key lock function is also included. Threshold value Incident light intensity General purpose Commercially-availabie connectors are used so that lead time and spare part numbers can both be reduced. The connectors used are commerciallyavailable connectors, so that processing costs and lead time required for carrying out processing after purchase of the sensors can be greatly reduced. The same connection parts as the DP-100 series of digital pressure sensors and the PM-64 series of micro photoelectric sensors can be used. Commercially-available press-fit connectors are used, so that the processing costs for connection cables can be greatly reduced. Conventional (cable type) Conventional lead time ;Harness ss processing p by outside order after sensor preparation Customer Sensor preparation 1 Sensor purchase and preparation 2 Harness processing by outside order Harness processor From now on (built-in connector type) Sensor installation Harness Processing Lead time from now on ;Harness ss processing p by outside order Customer Sensor preparation 1 Sensor purchase and preparation 2 Harness processing by outside order Harness processor Using cables with connectors Sensor installation Lead time further reduced Customer Sensor preparation Sensor installation Reduced 1 Purchase of sensors and cable with connectors SUNX fiber sensor product lineup Select the best types to suit your application. Digital type FX-300 (High function) FX-410 (Volume setting) FX-100 Analog control-type 1 Reduced Harness Processing FX-101 (Standard type) FX-102 (Long sensing range type) FX-311 (General purpose) Reduced lead time Digital fiber sensor DIN rail installation also possible 9 mm 0.354 in thickness "3.2 "0.126 mounting hole Direct installation possible without bracket Designed in a 3-layer structure to accommodate basic settings through to advanced settings. Setting details are divided into three levels for clearer operation, so that settings for normal operation are made in `RUN mode', basic settings are made in `SET mode', and advanced functions are set in `PRO mode'. This makes setting operations much easier to understand and carry out. RUN mode Functions used during normal operation RUN MODE Simple setting [ function table ] * Changing threshold values * Key lock * Quick settings * Code settings SET mode Functions used when initializing the sensor and carrying out maintenance [ function table ] SET MODE * Teaching * L-ON / D-ON setting * Timer setting * Light-emitting amount selection * Emission frequency setting function PRO mode Equipped with a full complement of digital fiber sensor functions PRO MODE Special and detailed setting The same operating system is shared by the widely-acclaimed DP-100 series of digital pressure sensors. The `100' is the indicator for easy handling. [ function table ] * Shift * External input * Reset * GETA * ECO * Display reversing * Surplus value display * Copy * Threshold value seeking cycle setting Digital pressure sensor DP-100 series 2 Easy for inexperienced operators to use, and experienced operators will still be satisfied too. Introducing sensors with a full complement of functions to support the needs of your workplace. Changing threshold values Quick code input function For For factory operators designers Sensor settings can be made simply by selecting preset values. Key lock Quick settings Code settings Quick setting numbers (summary) No. Output operation Light-emitting amount selection Dark-ON OFF None Dark-ON ON None Dark-ON OFF OFF-delay 10 ms Dark-ON ON OFF-delay 10 ms Light-ON ON ON-delay 40 ms Light-ON OFF ON-delay 40 ms Light-ON ON ON-delay 10 ms Light-ON OFF ON-delay 10 ms Timer Smooth support via telephone Confirmation can be carried out smoothly via telephone by simply quoting numbers. This can be of great assistance when dealing with overseas customers. 3 Teaching L-ON / D-ON setting Teaching using ON / OFF buttons For factory operators Simply press the ON button when an object is present and OFF when it is not. There is no need to switch ) settings or make judgments between Light-ON ( and Dark-ON ( ). <Setting example> Thru-beam type Timer setting Light-emitting amount selection Interference prevention function If the light receiving level becomes saturated when sensing over short distances or when sensing transparent objects or minute objects, the light emitting amount can be adjusted so that stable sensing can be provided without needing to change the response time. Emission frequency setting function ( Object present ON Object absent OFF For designers Light-emitting amount selection function ) For factory operators The emission frequencies can be set separately for each unit in order to avoid interference. The emitted light flashes while setting is in progress, so that you can see at a glance which fiber sensor is currently being set. In addition, this interference prevention is not done by using optical communication. This means that there is no need to place the amplifiers close together like there was before, and so the amplifiers can be set up apart from each other. Reflective type mWhen the emission frequencies are changed, the response times will also change. Object present ON Object absent OFF Limit teaching function This carries out teaching and sets threshold values only when no object is present (when the incident light amount is stable). This is useful when sensing objects if there are other objects in the background and when sensing minute objects. Teaching can also be carried out using external input. Shift External input This function seeks changes in the light emitting amount resulting from changes in the environment over long periods (such as dust levels), so that the incident light intensity can be checked at desired intervals and the threshold values can For factory operators Current value Threshold value GETA ECO Display reversing Surplus value display Copy Reset External input function Settings such as emission (Brown) halt, limit / auto teaching (Black) Output and ECO settings can be (White) External input carried out via external (Blue) 0 V input. V External input lines are equipped as standard Time (Price) be reset automatically. Incident light intensity Threshold value seeking cycle setting function Threshold value seeking cycle setting The functions and performance of a digital fiber sensor at an easily-affordable price! ;Digital type FX-300 FX-411 ;Analog control-type SUNX digital-type sensors have never been more accessible than this. And they are ideal as replacement products for analog control types and teaching types also. FX-100 target ;Teaching type Performance (sensing range), operability 4 FX-100 ORDER GUIDE Amplifiers Appearance Model No. M8 plug-in connector type Cable set (Note 1) Standard type M8 plug-in connector type Type Accessory Emitting element Output FX-101 (Note 2) NPN open-collector transistor FX-101-Z (Note 3) NPN open-collector transistor FX-101P (Note 2) PNP open-collector transistor FX-101P-Z (Note 3) PNP open-collector transistor FX-101-CC2 NPN open-collector transistor FX-101P-CC2 PNP open-collector collector transistor * CN-14A-C2 ( 6.562 ft ) mOnly include cable set type M8 plug-in connector type M8 plug-in connector type Cable set (Note 1) Long sensing range type Red LED FX-102 (Note 2) NPN open-collector transistor FX-102-Z (Note 3) NPN open-collector transistor FX-102P (Note 2) PNP open-collector transistor FX-102P-Z (Note 3) PNP open-collector transistor FX-102-CC2 NPN open-collector transistor FX-102P-CC2 PNP open-collector transistor Notes: 1) The connector attached cable CN-14A-C2 is supplied with the amplifier. 2) Make sure to use the optional connector attached cable CN-14A-C or the connector CN-14A. 3) Make sure to use the optional M8 connector attached cable CN-24A-C. OPTIONS M8 connector attached cable Designation Model No. Description 31.4 1.236 CN-14A-C1 1 m 3.281 ft Connector attached cable CN-14A-C2 2 m 6.562 ft (Note) CN-14A-C3 3 m 9.843 ft 0.02 mm2 4-core cabtyre cable with connector on one end Cable outer diameter: "3.7 mm "0.146 in CN-14A-C5 5 m 16.404 ft CN-24A-C5 For M8 plug-in connector type The connector on one end 5 m 16.404 ft Cable outer diameter: "4 mm "0.157 in Connector CN-14A Set of 10 housings and 40 contacts Protection cover FC-FX-1 This protects the operating surfaces. Amplifier mounting bracket MS-DIN-4 Mounting bracket for amplifier MS-DIN-E When it moves depending on the way it is installed on a DIN rail, these end plates ensure that all amplifiers are mounted together in a secure and fully connected manner. M8 connector attached cable End plates CN-24A-C2 2 m 6.562 ft Two pcs. per set Note: The connector attached cable CN-14A-C2 is supplied with the cable set type FX-10(P)-CC2. M8 connector attached cable CN-24A-CI * CN-24A-C "4 "0.157 "9 "0.354 Fixing ring Protection cover * FC-FX-1 Amplifier mounting bracket * MS-DIN-4 Connector attached cable * CN-14A-C Connector Contact * Housing 5 FX-100 SPECIFICATIONS Item Model No. Type Standard type Long sensing range type Cable set Cable set NPN output FX-101 (-Z) (Note 4) FX-101-CC2 FX-102 (-Z) (Note 4) FX-102-CC2 PNP output FX-101P (-Z) (Note 4) FX-101P-CC2 FX-102P (-Z) (Note 4) FX-102P-CC2 12 to 24 V DC10 % Ripple P-P 10 % or less Supply voltage Power consumption Output Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) <NPN output type> NPN open-collector transistor * Maximum sink current:100 mA * Applied voltage: 30 V DC or less (between output and 0 V) * Residual voltage: 1.5 V or less (at 100 mA sink current) Output operation Selectable either Light-ON or Dark-ON, at SET mode Short-circuit protection External input Response time Incorporated <NPN output type> NPN non-contact input * Signal condition High: 8 V to V DC or Open Low: 0 to2 V DC (Source current 0.5 mA or less) * Input impedance: 10 k approx. <PNP output type> PNP non-contact input * Signal condition High: 4 V toV DC (Sink current 0.5 to 3 mA) Low: 0 to0.6 V DC or Open * Input impedance: 10 k approx. Emission frequency 0: 250 !s or less Emission frequency 1: 450 !s or less Emission frequency 2: 500 !s or less Emission frequency 3: 600 !s or less Sensitivity setting Emission frequency 1: 2.5 ms or less Emission frequency 2: 2.8 ms or less Emission frequency 3: 3.2 ms or less Emission frequency 4: 5.0 ms or less 2-level teaching / Limit teaching / Full-auto teaching Operation indicator Orange LED (lights up when the output is ON) 4 digits (green)4 digits (red) LCD display Digital display Fine sensitivity adjustment function Timer function Incorporated ON-delay / OFF-delay timer, switchable either effective or ineffective. [Timer period:1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms] Light emitting amount selection function Environmental resistance Interference prevention function Ambient temperature Incorporated / Switchable either effective or ineffective Incorporated Emission frequency selection method (Note 2) (Functions at emission frequency 1, 2 or 3) Incorporated Emission frequency selection method (Note 2) (Functions at emission frequency 1, 2 , 3 or 4) 10 to 55 C 14 to 131 F (If 4 to 7 units are mounted close together: 10 to 50 C 14 to 122 F, if 8 to 16 units are : 10 to 45 C 14 to 113 F) (No dew condensation or icing allowed), Storage: 20 to 70 C 4 to 158 F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Incandescent light: 3,000 ?x at the light-receiving face Ambient illuminance Voltage withstandability <PNP output type> PNP open-collector transistor * Maximum source current: 100 mA * Applied voltage: 30 V DC or less (between output and V) * Residual voltage: 1.5 V or less (at 100 mA source current) 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 3) Insulation resistance 20 M, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 3) Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each Shock resistance 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each Emitting element (modulated) Material Red LED (Peak emission wavelength : 632 nm) Enclosure: Polycarbonate, Key switch: Polycarbonate, Fiber lock lever: PBT Connecting method Cable extension Weight Accessory Connector (Note 4) Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. Net weight: 15 g approx. Gross weight: 35 g approx. Net weight: 15 g approx. Gross weight: 75 g approx. CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long):1pc. Net weight: 15 g approx. Gross weight: 35 g approx. Net weight: 15 g approx. Gross weight: 75 g approx. CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long):1pc. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were ambient temperature 23 C 73.4 F. 2) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values. However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2. 3) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. 4) Connector attached cable CN-14A-C2 is not attached to the models that have no `-CC2' at the end of the model Nos. Make sure to use the optional connector attached cable CN-14A-C or the connector CN-14A. Model Nos. having the suffix `-Z' are M8 plug-in connector type. Make sure to use the optional M8 plug-in connector cable CN-24A-C. 6 FX-100 I/O CIRCUIT AND WIRING DIAGRAMS FX-10((-Z/-CC2)) NPN output type I/O circuit diagram Terminal arrangement diagram Connector type Terminal No. Color code of cable with connector (Brown) 1 Sensor circuit D Tr 8V ZD V (White) Extemal input 3 Internal circuit 12 to 24 V DC 10 % 2 3 4 m1 (Blue) 0 V 4 Terminal No. 1 Load (Black) Output 2 100 mA max. Function 1 V 2 Output 3 External input 4 0V Users' circuit Symbols ... D : Reverse supply polarity protection diode ZD : Surge absorption zener diode Tr : NPN output transistor M8 plug-in connector type m1 Non-voltage contact or NPN open-collector transistor 1 Terminal No. 2 or 3 High (8 V to V DC or open): Ineffective Low [(0 to 2 V DC (source current 0.5 mA or less)] : Effective 4 Function 1 V 2 Output 3 External input 4 0V FX-10P((-Z/-CC2)) PNP output type I/O circuit diagram Terminal arrangement diagram Terminal No. Connector type Color code of cable with connector Sensor circuit (Brown) 1 V m1 ZD Tr D Internal circuit 100 mA max. 2 (Black) Output (Blue) 0 V 4 Load Terminal No. 1 (White) External input 3 12 to 24 V DC 10 % 2 3 4 V 2 Output 3 External input 4 0V Users' circuit Symbols ... D : Reverse supply polarity protection diode ZD : Surge absorption zener diode Tr : PNP output transistor M8 plug-in connector type m1 Non-voltage contact or PNP open-collector transistor 1 Terminal No. 2 or High [4 V to V DC (sink current 0.5 to 3 mA)]: Effective Low (0 to 0.6 V DC or open): Ineffective 7 Function 1 3 4 Function 1 V 2 Output 3 External input 4 0V FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Thru-beam type (one pair set) Type Shape of fiber head (mm in) Lens mountable Standard type FX-101 M4 Lens mountable Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note) 400 15.748 FT-B8 1,150 45.276 R25 mm R0.984 in M4 FT-FM2 Sleeve 90 mm 3.543 in M4 M4 800 31.496 300 11.811 "1.48 "0.058 Sleeve 40 mm 1.575 in 2m 6.562 ft M4 "1.48 "0.058 Lens mountable M4 Lens mountable M4 Lens mountable 260 10.236 230 9.055 FT-FM2S4 FT-W8 650 25.591 R4 mm R0.157 in Flexible FT-P80 1m 3.281 ft R10 mm R0.394 in FT-P81X 2m 6.562 ft R4 mm R0.157 in Flexible FT-P60 260 10.236 800 31.496 M4 300 11.811 Nut type M4 Lens mountable Lens mountable (except FX-LE2) 570 22.441 215 8.465 W7 H9 D13.9 W0.276 H0.354 D0.547 With lens M4 430 16.929 W7 H9 D14.6 W0.276 H0.354 D0.575 Elbow Threaded type FT-FM2S R1 mm R0.039 in Tough flexible 130 5.118 Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in 650 25.591 M4 Lens mountable Model No. M4 430 16.929 180 7.087 M3 1,150 45.276 2m 6.562 ft 2m 6.562 ft M3 M3 "0.88 "0.035 Sleeve 40 mm 1.575 in FT-T80 FT-NFM2 130 5.118 280 11.024 2m 6.562 ft "0.88 "0.035 Long sensing range g M3 With lens FT-R80 R25 mm R0.984 in M3 M3 R25 mm R0.984 in 800 31.496 300 11.811 FT-WR80 FT-WR80L M3 Sleeve 90 mm 3.543 in R1 mm R0.039 in Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in FT-NFM2S FT-NFM2S4 80 3.150 220 8.661 R1 mm R0.039 in FT-W4 80 3.150 240 9.449 R4 mm R0.157 in Flexible FT-P40 M14 9,300 366.141 15,000 590.550 10 m 32.808 ft R25 mm R0.984 in FT-FM10L Note: Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 8 FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Thru-beam type (one pair set) "3 "0.118 Type Shape of fiber head (mm in) Standard type FX-101 With lens * Long sensing range "3 "0.118 600 23.622 "3 "0.118 "2.5 "0.098 "1.5 "0.059 Cylindrical type Ultra-small diameter "1 "0.039 "1 "0.039 Beam diameter "0.125 mm "0.005 in "0.25 "3 "0.010 "0.118 800 31.496 300 11.811 "0.4 "3 "0.016 "0.118 FT-SFM2L 130 5.118 R1 mm R0.039 in R25 mm R0.984 in 280 11.024 2m 6.562 ft 220 8.661 80 3.150 1m 3.281 ft 330 12.992 120 4.724 500 mm 19.685 in 90 3.543 40 1.575 1m 3.281 ft 60 2.362 15 0.591 R1 mm R0.039 in Sleeve part cannot be bent. "1.5 "0.059 Side-view 0.88 0.031 0 "2.5 "0.098 180 7.087 470 18.504 Sleeve p part cannot be bent. "1 "0.039 0.66 0.024 0 "2 "0.079 140 5.512 380 14.961 Sleeve part cannot be bent. FT-PS1 FT-E22 FT-V10 2m 6.562 ft 1m 3.281 ft FT-SFM2SV2 R25 mm R0.984 in FT-V22 "1 "0.039 0.66 0.024 0 "2.5 "0.098 40 1.575 1 0.039 0 "2 "0.079 Sleeve part cannot be bent. 30 1.181 FT-V41 120 4.724 Sleeve part cannot be bent. "1 "0.039 80 3.150 2m 6.562 ft R1 mm R0.039 in Note: Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 9 FT-WS4 FT-E12 2,350 92.520 1,000 39.370 FT-SNFM2 R5 mm R0.197 in "4 "0.157 3 0.118 FT-WS8 FT-P2 R4 mm R0.157 in Flexible 500 mm 19.685 in 19 0.748 6 0.236 FT-SFM2 2m 6.562 ft 650 25.591 260 10.236 Sleeve part cannot be bent. Beam diameter "0.25 mm "0.010 in FT-WS3 R25 mm R0.984 in "2.5 "0.098 "1.5 "0.059 2m 6.562 ft R1 mm R0.039 in 2,400 94.488 760 29.921 "2.5 "0.098 "1.5 "0.059 600 23.622 Model No. FT-WS8L 1,500 59.055 150 5.906 With lens * Long sensing range "2.5 "0.098 "1.5 "0.059 Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note) FT-WV42 FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Thru-beam type (one pair set) Type Shape of fiber head (mm in) Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1) Standard type FX-101 Easy mounting * Top sensing W3 H8 D12 W0.118 H0.315 D0.472 Model No. 1,200 47.244 2,800 110.236 R1 mm R0.039 in FT-WZ8H 1,400 55.118 3,100 122.047 R4 mm R0.157 in Flexible FT-Z8H 2,100 82.677 R1 mm R0.039 in FT-WZ8E R4 mm R0.157 in Flexible FT-Z8E R1 mm R0.039 in FT-WZ8 R4 mm R0.157 in Flexible FT-Z8 Easy mounting * Side sensing W3 H12 D8 W0.118 H0.472 700 27.559 D0.315 800 31.496 1,850 72.835 2m 6.562 ft Compact Rectangular Easy mounting * Front sensing 950 37.402 330 12.992 W8.5 H12 D3 W0.335 H0.472 D0.118 360 14.173 1,000 39.370 Front sensing W10 H7 D2 W0.394 H0.276 D0.079 Fiber bending type W2 H10 D10 W0.079 H0.394 D0.394 670 26.378 230 9.055 80 3.150 FT-WZ4 1m 3.281 ft 230 9.055 R1 mm R0.039 in Front sensing W14 H7 D3.5 W0.551 H0.276 D0.138 Fiber bending type W3.5 H14 D11 W0.138 H0.551 D0.433 330 12.992 580 22.835 190 7.480 "3.5 "0.138 "3.7 "0.146 Narrow beam 1,000 39.370 1,000 39.370 Side-view type with small light dispersion "4 "0.157 700 27.559 3 0.118 FT-WZ7 2m 6.562 ft FT-WZ7HB 3,000 118.110 R25 mm R0.984 in 2,200 86.614 R1 mm R0.039 in 3,000 118.110 1,000 39.370 FT-WZ4HB 2m 6.562 ft FT-K8 FT-WKV8 R25 mm R0.984 in FT-KV8 R10 mm R0.394 in FT-KV1 R1 mm R0.039 in FT-WA30 R10 mm R0.394 in FT-A30 R1 mm R0.039 in FT-WA8 R10 mm R0.394 in FT-A8 W2 H1.5 D20 W0.079 H0.059 D0.787 2 0.079 135 5.315 500 19.685 Sensing width 32 mm 1.260 in Wide beam Special Wide area sensing W5 H69 D20 W0.197 H2.717 D0.787 (Note (No ote 2) 3,500 137.795 (Note (No ote 2) 3,500 137.795 2m 6.562 ft Wide area sensing Sensingg width 11 mm 0.433in 1,500 59.055 (Note (No ote 2) 3,500 137.795 W4.2 H31 D13.5 W0.165 H1.220 D0.531 Array Top sensing W5 H15 D15 W0.197 H0.591 D0.591 280 11.024 Side sensing W5 H15 D15 W0.197 H0.591 D0.591 240 9.449 FT-AFM2 720 28.346 670 26.378 2m 6.562 ft R25 mm R0.984 in FT-AFM2E Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) The fiber cable length practically limits the sensing range to 3,500 mm 137.795 in long. 10 FX-100 LIST OF FIBERS Thru-beam type (one pair set) Type Shape of fiber head (mm in) 350 C 662 F Lens mountable Standard type FX-101 M4 350 C 662 F Sleeve 60 mm 2.362 in Heat-resistant Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1) 170 6.693 490 19.291 2m 6.562 ft M4 "2.1 "0.083 Allows flexible wiring 200 C 392 F Lens mountable 200 C 392 F Lens mountable M4 M4 130 C 266 F Lens mountable (FX-LE2 only) M4 100 3.937 300 11.811 540 21.260 210 8.268 250 9.843 700 27.559 1m 3.281 ft 1m 3.281 ft R25 mm R0.984 in Model No. FT-H35-M2 Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in FT-H35-M2S6 R10 mm R0.394 in FT-H20W-M1 FT-H20-M1 R25 mm R0.984 in 2m 6.562 ft FT-H13-FM2 200 mm 7.874 in (Note 2) FT-H20-J20-S Special Heat-resistant * Joint Lens mountable (FX-LE1) M4 Side-view 150 5.906 Easy mounting * Rectangular head SEMI S2 compliant W7 H15 D13 W0.276 H0.591 D0.512 500 19.685 520 20.472 "5.5 "0.217 Side-view 3,100 122.047 "5.5 "0.217 300 C 572 F Lens mountable (FV-LE1/SV2 only) M4 110 4.331 FT-H20-J30-S Heatresistant side fiber R18 mm R0.709 in (Note 3) 800 31.496 280 11.024 (Note 4) FT-H20-J50-S (Note 4) 500 mm 19.685 in (Note 2) FT-H20-VJ50-S 800 mm 31.496 in (Note 2) FT-H20-VJ80-S 2m 6.562 ft (Note 4) (Note 4) R25 mm R0.984 in FT-Z802Y FT-L80Y 2,600 102.362 1,100 43.307 340 13.386 Vacuumresistant 300 mm 11.811 in (Note 2) 500 mm 19.685 in (Note 2) "3.8 "0.150 "4 "0.157 Chemical-resistant 420 16.535 135 5.315 (Note 4) 2m 6.562 ft (Note 5) R30 mm R1.181 in 1m 3.281 ft R18 mm R0.709 in FT-V80Y FT-H30-M1V-S (Note 6) Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) This is the fiber length (fixed length) for heat-resistant side fibers. The ordinary-temperature side fibers are free-cut to 2 m 6.562 ft. 3) The ordinary-temperature side fiber is R25 mm R0.984 in or more. 4) Heat-resistant joint fibers and ordinary-temperature side fibers (FT-FM2) are sold as a set. Please refer to `Heat-resistant joint fiber catalog' for details. 5) The allowable cutting range is 500 mm 19.685 in from the end that the amplifier inserted. 6) Sold as a set comprising vacuum-resistant type fiberphoto-terminal (FV-BR1)fiber at atmospheric side (FT-J8). Please refer to `Vacuum-resistant fiber catalog' for details. Model No. when ordering heat-resistant joint fibers individually as replacement parts * FT-H20-J20 (one pair set) * FT-H20-VJ50 (one pair set) * FT-H20-J30 (one pair set) * FT-H20-VJ80 (one pair set) * FT-H20-J50 (one pair set) Model No. when ordering vacuum-resistant fibers individually as replacement parts * Vacuum-resistant type fiber FT-H30-M1V (one pair set) 11 * Photo-terminal FV-BR1 (one pair set) * Fiber at atmospheric side FT-J8 (one pair set) FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Retroreflective type Sharp bending Shape of fiber head (mm in) Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1, 2) Standard type FX-101 Model No. W9.5 H5.2 D15 W0.374 H0.205 D0.591 100 to 550 3.937 to 21.654 W30 H30 D0.5 W1.181 H1.181 D0.020 W9.5 H5.2 D21 W0.374 H0.205 D0.827 100 to 830 3.937 to 32.677 2m 6.562 ft R1 mm R0.039 in 2m 6.562 ft R10 mm R0.394 in 2m 6.562 ft R10 mm R0.394 in FR-WKZ11 FR-KZ21 W10.6 H28 D10.1 W0.417 H1.102 D0.398 W9.5 H25 D5.2 W0.374 H0.984 D0.205 200 7.874 200 7.874 FR-KZ21E W10.6 H28 D10.1 W0.417 H1.102 D0.398 W7.5 H2.2 D11.2 W0.295 H0.087 D0.441 Wafer mapping Narrow beam polarizing p Side sensing Top sensing With filters Type 15 to 200 0.591 to 7.874 15 to 360 0.591 to 14.173 FR-KV1 W4 H2 D21.5 W0.157 H0.079 D0.846 Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. The sensing range of FR-WKZ11 is specified for the RF-13. The sensing range of FR-KZ21, FR-KZ21E and FR-KV1 is specified for the attached reflector. The sensing ranges when using in combination with the FR-WKZ11 reflector (optional) are given in the below table. Reflector Amplifier FX-101 FX-102 FR-WKZ11RF-210 100 to 700 3.937 to 27.559 100 to 1,100 3.937 to 43.307 FR-WKZ11RF-220 100 to 1,300 3.937 to 51.181 100 to 2,600 3.937 to 102.362 FR-WKZ11RF-230 100 to 2,000 3.937 to 78.740 100 to 4,000 3.937 to 157.480 2) The sensing range of FR-WKZ11 is the possible setting range for the reflector or reflective tape. The fiber can detect an object less than 100 mm 3.937 in away. However, note that if there are any white or highly-reflective surfaces near the fiber head, reflected incident light may affect the fiber head. If this occurs, adjust the threshold value of the amplifier unit before use. The sensing range of FR-KZ21(E) is the possible setting range for the reflector. However, if setting the fiber to detect objects passing within 0 to 20 mm 0 to 0.787 in from the fiber head, unstable detection may result. The sensing range of FR-KV1 is the possible setting range for the reflector. The fiber can detect an object less than 15 mm 0.591 in away. Reflective type Type Shape of fiber head (mm in) M6 Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1, 2) Standard type FX-101 170 6.693 Coaxial M6 FD-B8 440 17.323 R25 mm R0.984 in 100 3.937 FD-FM2 410 16.142 Sleeve 90 mm 3.543 in M6 M6 Threaded type "2.5 "0.098 Sleeve 40 mm 1.575 in M6 100 3.937 345 13.583 2m 6.562 ft "2.5 "0.098 M6 80 3.150 90 3.543 230 9.055 200 7.874 M6 M6 70 2.756 220 8.661 Elbow Tough flexible M6 Model No. 70 2.756 180 7.087 1m 3.281 ft 2m 6.562 ft Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in FD-FM2S FD-FM2S4 R1 mm R0.039 in FD-W8 R4 mm R0.157 in Flexible FD-P80 R10 mm R0.394 in FD-P81X R25 mm R0.984 in FD-R80 Notes: 1) The sensing range is specified for white non-glossy paper (400400 mm 15.74815.748 in) as the object. 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 12 FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Reflective type Type Shape of fiber head (mm in) M4 Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1, 2) Standard type FX-101 110 4.331 FD-T80 345 13.583 R25 mm R0.984 in M4 FD-NFM2 Sleeve 90 mm 3.543 in M4 35 1.378 Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in 100 3.937 "1.48 "0.058 Sleeve 40 mm 1.575 in M4 "1.48 "0.058 M4 Sleeve 40 mm 1.575 in M4 15 0.591 40 1.575 2m 6.562 ft "1.48 "0.058 M4 80 3.150 Small spot for sensing minute objects Coaxial * Lens mountable Threaded type 28 1.102 50 1.969 M4 230 9.055 75 2.953 120 4.724 150 5.906 45 1.772 M4 Small diameter 35 1.378 100 3.937 M3 M3 15 0.591 M3 8 0.315 Lens mountable (FX-MR3, FX-MR6) M3 M3 Coaxial Lens mountable (FX-MR3, FX-MR6) M3 Tough flexible Coaxial Coaxial * Lens mountable (FX-MR3, FX-MR6) M3 50 1.969 18 0.709 Coaxial * Lens mountable (FX-MR3, FX-MR6) M3 Light emitting fiber element 7 0.276 High precision "0.125 "0.005 "0.5 "0.020 Sleeve part cannot be bent. Coaxial "0.8 "0.031 M3 Sleeve part cannot be bent. 40 1.575 1 0.039 15 0.591 2m 6.562 ft 30 1.181 120 4.724 160 6.299 45 1.772 High precision Coaxial * Lens mountable (FX-MR3, FX-MR6) M3 Light emitting fiber element 10 0.394 High precision "0.175 "0.007 M3 Model No. 1m 3.281 ft (Note 3) 50 1.969 FD-NFM2S4 Fiber R1 mm R0.039 in Sleeve R10 mm R0.394 in FD-W44 R1 mm R0.039 in FD-WT8 R2 mm R0.079 in FD-WG4 R25 mm R0.984 in FD-G4 R4 mm R0.157 in Flexible FD-P60 R25 mm R0.984 in FD-T40 R1 mm R0.039 in FD-WT4 R4 mm R0.157 in Flexible FD-P40 R25 mm R0.984 in FD-G6 R10 mm R0.394 in FD-G6X R25 mm R0.984 in FD-EG1 30 1.181 FD-EG2 500 mm 19.685 in R10 mm R0.394 in 22 0.866 FD-EG3 4 0.157 48 1.890 FD-NFM2S FD-EN500S1 1m 3.281 ft R25 mm R0.984 in FD-ENM1S1 Notes: 1) The sensing range is specified for white non-glossy paper [200200 mm 7.8747.874 in (FD-T80, FD-WT8: 400400 mm 15.74815.748 in, FD-W44, FD-WT4, FD-P40, FD-G6, FD-EG1, FD-EG2, FD-EG3, FD-EN500S1, FD-ENM1S1: 100100 mm 3.9373.937 in)] as the object. 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The allowable cutting range is 700 mm 27.559 in from the end that the amplifier inserted. 13 FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Reflective type Shape of fiber head (mm in) Type "3 "0.118 "3 "0.118 Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1, 2) Standard type FX-101 100 3.937 "3 "0.118 345 13.583 80 3.150 230 9.055 Coaxial 28 1.102 75 2.953 2m 6.562 ft "3 "0.118 "1.5 "2.5 "0.059 "0.098 Ultra-small diameter 150 5.906 45 1.772 "2.5 "0.098 35 1.378 "1.5 "0.059 Side-view Cylindrical type "3 "0.118 25 0.984 "1.5 " "0.5 "0.059 "0.020 3.5 0.138 Sleeve part cannot be bent. Coaxial "3 "0.118 "0.65 "0.026 Sleeve part cannot be bent. Small diameter "1.5 "0.059 0.77 0.028 0 "3 "0.118 Sleeve part cannot be bent. "2 " "3 " "0.118 "0.079 1 0.039 0 Sleeve part cannot be b bent. "2 " "5 " "0.197 "0.079 0.88 0.031 0 Sleeve part cannot be b bent. Glass substrate detection * Mapping 65 2.559 2m 6.562 ft 1m 3.281 ft 13 0.512 1m 3.281 ft 16 0.630 25 0.984 6 0.236 30 1.181 16 to 30 0.630 to 1.181 W25 H7.3 D30 W0.984 H0.287 D1.181 Glass substrate detection * Alignment W20 H29 D3.8 W0.787 H1.142 D0.150 100 3.937 0 to 40 0 to 1.575 45 1.772 70 2.756 20 0.787 2m 6.562 ft 90 3.543 12 to 50 0.472 to 1.969 0 to 50 0 to 1.969 4m 13.123 ft 3m 9.843 ft Glass substrate detection * Alignment Rectangular Convergent reflective type W17 H29 D3.8 W0669 H1.142 D0.150 Glass substrate detection * Seating confirmation W12 H19 D3 W0.472 H0.748 0 to 6 0 to 0.236 0 to 25 0 to 0.984 R25 mm R0.984 in FD-S80 R1 mm R0.039 in FD-WS8 R2 mm R0.079 in FD-WSG4 R4 mm R0.157 in Flexible FD-P50 R25 mm R0.984 in R4 mm R0.157 in Flexible FD-P2 R10 mm R0.394 in FD-E12 R25 mm R0.984 in FD-E22 R25 mm R0.984 in FD-V41 R1 mm R0.039 in 0 to 5.5 0 to 0.217 7 to 12 0.276 to 0.472 (Convergent point 8 0.315) 6 to 13.5 0.236 to 0.531 (Convergent point 8 0.315) 3 to 14 0.118 to 0.551 (Convergent point 8 0.315) 1.5 to 16 0.059 to 0.630 (Convergent point 8 0.315) FD-WV42 R25 mm R0.984 in FD-SFM2SV2 R25 mm R0.984 in FD-L46 FD-L45 R4 mm R0.157 in FD-L43 2m 6.562 ft 0 to 8 0 to 0.315 0 to 4.5 0 to 0.177 FD-SNFM2 FD-L44 2m 6.562 ft R10 mm R0.394 in FD-L44S D0.118 Glass substrate detection W24 H21 D4 W0.945 H0.827 0 to 19 0 to 0.748 Model No. D0.157 W6 H18 D14 W0.236 H0.709 D0.551 W7.2 H7.5 D2 W0.283 H0.295 D0.079 5 to 8 0.197 to 0.315 (Convergent point 6 0.236) 1 to 4.5 0.039 to 0.177 R1 mm R0.039 in 2m 6.562 ft 1 to 17 0.039 to 0.669 (Convergent point 6 0.236) 0.5 to 6.5 0.020 to 0.256 FD-WL41 FD-L41 R10 mm R0.394 in FD-L4 1m 3.281 ft R1 mm R0.039 in FD-WL48 Notes: 1) The sensing range is specified for white non-glossy paper (FD-S80, FD-WS8: 400400 mm 15.74815.748 in, FD-WSG4, FD-P50, FD-SNFM2, FD-V41, FD-SFM2SV2: 200200 mm 7.8747.874 in, FD-P2, FD-E12, FD-E22, FD-WV42, FD-L4, FD-WL48: 100100 mm 3.9373.937 in, FD-L46: 100100t 0.7 mm 3.9373.937t 0.028 in R edge of LCD glass substrates, FD-L43, FD-L44 4 and FD-L45: 100100t 0.7 mm 3.9373.937t 0.028 in LCD glass substrates, FD-L44S: silicon wafers polished surface, FD-WL41, FD-L41: 100100t 2 mm 3.9373.937t 0.079 in glass substrates) 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 14 FX-100 LIST OF FIBERS Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table. Reflective type Type Shape of fiber head (mm in) Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1, 2) Standard type FX-101 Model No. Front sensing Compact Array Liquid level sensing Special sensing Wide beam Long range g Rectangular W10 H7 D2 W0.394 H0.276 D0.079 Fiber bending type Front sensing FD-WZ4 2 to 20 0.079 to 0.787 1 to 70 0.039 to 2.756 1m 3.281 ft W2 H D10 W0.079 H0.394 D0.394 W14 H7 D3.5 W0.551 H0.276 D0.138 Fiber bending type W3.5 H14 D11 W0.138 H0.551 D0.433 Long sensing range * Rectangular head W5.2 5 D15 W0.205 H0.374 D0.591 R1 mm R0.039 in 1 to 55 0.039 to 2.165 1 to 60 0.039 to 2.362 20 to 180 0.787 to 7.087 125 4.921 160 6.299 FD-WZ7 0.5 to 180 0.020 to 7.087 20 to 480 0.787 to 18.898 250 9.843 W7 H15 D30 W0.276 H0.591 D1.181 Top sensing W5 H20 D20 W0.197 H0.787 D0.787 Side sensing W5 H20 D20 W0.197 H0.787 D0.787 Contact type "6 "0.236 Mountable on pipe * Standard W25 H13 D20 W0.984 H0.512 D0.787 Mountable on pipe * For PFA, wall thickness 1 mm 0.039 in pipe W25 H13 D20 W0.984 H0.512 D0.787 105 4.134 85 3.346 FD-WZ4HB 2m 6.562 ft FD-WZ7HB 2m 6.562 ft 2m 6.562 ft R1 mm R0.039 in R25 mm R0.984 in 285 11.220 245 9.646 Applicable pipe diameter: Outer dia. "6 to "26 mm "0.236 to "1.024 in transparent pipe [PFA (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.039 in] FD-A15 FD-AFM2 2m 6.562 ft 2m 6.562 ft (Note 3) Applicable pipe diameter: Outer dia. "6 to "26 mm "0.236 to "1.024 in transparent pipe [PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm 0.039 to 0.118 in] FD-WKZ1 R25 mm R0.984 in FD-AFM2E Protective tube R40 mm R1.575 in Fiber R15 mm R0.591 in FD-F8Y FD-F41 2m 6.562 ft R10 mm R0.394 in FD-F4 Notes: 1) The sensing range is specified for white non-glossy paper [200200 mm 7.8747.874 in (FD-WKZ1, FD-AFM2, FD-AFM2E: 400400 mm 15.47815.478 in)] as the object. 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) The allowable cutting range is 1,000 mm 39.370 in from the end that the amplifier inserted. 15 FX-100 LIST OF FIBERS Reflective type Type Shape of fiber head (mm in) Fiber cable Bending length Long sensing range type FX-102 : Free-cut radius Sensing range (mm in)(Note 1, 2) Standard type FX-101 350 C 662 F * Coaxial M6 350 C 662 F * Sleeve 60 mm 2.362 in "2.8 " M6 "0.110 200 C 392 F * Coaxial M6 75 2.953 2m 6.562 ft 280 11.024 120 4.724 Heat-resistant Special 350 C 662 F * Sleeve 90 mm 3.543 in "2.1 " "0.083 200 C 392 F * Coaxial 1m 3.281 ft 200 7.874 M4 90 3.543 Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in FD-H35-M2S6 Fiber R25 mm R0.984 in Sleeve R10 mm R0.394 in FD-H35-20S FD-H20-21 280 11.024 M4 300 C 572 F * Glass substrate detection Convergent reflective type W19 H27 D5 W0.748 H1.063 D0.197 2 to 9 0.079 to 0.354 180 C 356 F * Glass substrate detection Convergent reflective type y W19 H27 D5 W0.748 H1.063 D0.197 130 C 266 F M6 Vacuum-resistant R25 mm FD-H35-M2 R0.984 in R25 mm FD-H20-M1 R0.984 in 300 11.811 85 3.346 Model No. 0 to 10 0 to 0.394 2m 6.562 ft 0 to 17 0 to 0.669 FD-H30-L32 R25 mm R0.984 in 0 to 25 0 to 0.984 100 3.937 FD-H18-L31 2m 6.562 ft 280 11.024 FD-H13-FM2 300 C 572 F * Rectangular head W9.5 H5.2 D15 W0.374 H0.205 D0.591 300 C 572 F * Glass substrate detection Convergent reflective type W19 H5 D27 W0.748 H0.197 D1.063 25 to 80 0.984 to 3.150 2.5 to 6.5 0.098 to 0.256 10 to 220 0.394 to 8.661 1m 3.281 ft 3m 9.843 ft 0 to 11 0 to 0.433 R18 mm R0.709 in FD-H30-KZ1V-S (Note 3) FD-H30-L32V-S (Note 3) Notes: 1) The sensing range is specified for white non-glossy paper [400400 mm 15.74815.748 in (FD-H30-L32, FD-H18-L31: 5050 mm 1.9691.969 in glass substrate, FD-H30-KZ1V-S, FD-H30-L32V-S: 100100t 0.7 mm 3.9373.937t 0.028 in transparent glass)] as the object. 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) Sold as a set comprising vacuum-resistant type fiberphoto-terminal (FV-BR1)fiber at atmospheric side (FT-J8). Model No. when ordering vacuum-resistant fibers individually as replacement parts * Vacuum-resistant type fiber FD-H30-KZ1V FD-H30-L32V * Mounting bracket for FD-H30-KZ1V MS-FD-2 * Photo-terminal FV-BR1 (one pair set) * Fiber at atmospheric side FT-J8 (one pair set) Accessories (attached with fibers) RF-003 (FR-KZ21/KZ21E exclusive reflector) * RF-003 RF-13 (Reflective tape) FX-CT1 (Fiber cutter) FX-CT2 (Fiber cutter) FX-AT2 (Attachment for fixed-length fiber, Orange) FX-AT3 (Attachment for "2.2 mm "0.087 in fiber, Clear orange) FX-AT4 (Attachment for "1 mm "0.039 in fiber, Black) FX-AT5 (Attachment for "1.3 mm "0.051 in fiber, Gray) FX-AT6 (Attachment for "1 mm "0.039 in / "1.3 mm "0.051 in mixed fiber, Black / Gray) If connecting to a fiber amplifier other than the FX-100 series Applicable fiber amplifiers: FX2 / FX3 series FX-AT10 (Attachment for "1 mm "0.039 in fiber) FX-AT13 (Attachment for "1.3 mm "0.051 in fiber) FX-AT15 (Attachment for "1 mm "0.039 in / "1.3 mm "0.051 in mixed fiber) * RF-13 * FX-CT1 * FX-CT2 * FX-AT2 * FX-AT3 * FX-AT4 * FX-AT10 * FX-AT13 * FX-AT15 * FX-AT5 * FX-AT6 16 FX-100 FIBER OPTIONS Lens (For thru-beam type fiber) Designation Model No. Description Increases the sensing range by 5 times or more. For thru-beam type fiber Expansion lens (Note 1) * Ambient temperature: 60 to 350 C 76 to 662 F FX-LE1 Tremendously increases the sensing range with large diameter lenses. Superexpansion lens (Note 1) FX-LE2 Side-view lens Side-view lens for vacuumresistant fiber FV-LE1 FX-SV2 Amplifier Fiber FX-101 FX-102 FT-B8 FT-FM2, FT-T80 FT-R80 FT-W8 FT-P80, FT-P60 FT-P81X FT-H35-M2 FT-H20W-M1 FT-H20-M1 FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S 2,200 3,000 1,900 3,000 3,500 (Note 2) 1,600 (Note 2) 2,000 1,300 1,600 (Note 2) 1,000 3,500 (Note 2) 3,500 (Note 2) 3,500 (Note 2) 3,500 (Note 2) 3,500 (Note 2) 1,600 (Note 2) 3,500 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 3,500 (Note 2) Sensing range (mm) [Lens on both sides] Amplifier Fiber FX-101 FX-102 * Ambient temperature: 60 to 350 C 76 to 662 F FT-B8,, FT-FM2,, FT-R80,, FT-W8,, FT-P80,, FT-P60 FT-P81X FT-H35-M2 FT-H20W-M1, FT-H20-M1 FT-H13-FM2 FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S 3,500 (Note 2) 1,600 (Note 2) 3,500 (Note 2) 1,600 (Note 2) 3,500 (Note 2) 3,500 (Note 2) 3,500 (Note 2) 1,600 (Note 2) 3,500 (Note 2) 1,600 (Note 2) 3,500 (Note 2) 3,500 (Note 2) Beam axis is bent by 90 . Sensing range (mm) [Lens on both sides] * Ambient temperature: 60 to 300 C 76 to 572 F Fiber Sensing range increases by 4 times or more. * Ambient temperature: 40 to 120 C 40 to248 F Beam axis is bent by 90 . Sensing range (mm) [Lens on both sides] (Note 3) FX-SV1 Expansion lens for vacuumresistant fiber (Note 1) Sensing range (mm) [Lens on both sides] Amplifier FT-B8 FT-FM2, FT-T80 FT-W8 FT-P80 FT-P60 FT-P81X FT-H35-M2 FT-H20W-M1 FT-H20-M1 FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S Amplifier Fiber FT-H30-M1V FX-101 FX-102 530 550 450 420 300 550 280 140 280 150 1,450 1,700 1,300 1,400 850 1,700 800 400 840 410 FX-101 FX-102 450 1,600 , Sensing range (mm) [Lens on both sides] (Note 3) * Ambient temperature: Fiber 60 to 300 C 140 to572 F FT-H30-M1V Amplifier FX-101 FX-102 450 1,600 , Notes: 1) Be careful when installing the thru-beam type fiber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difficult. Especially when installing a fiber with many cores (sharp bending fibers and heat-resistant glass fiber), please be sure to use it only after you have adjusted it sufficiently. 2) The fiber cable length practically limits the sensing range to 3,500 mm 137.795 in long (FT-H20W-M1, FT-P81X X and FT-H20-M1: 1,600 mm 62.992 in). 3) The fiber cable length for the FT-H30-M1V V is 1m 3.281 ft. The sensing ranges in FX-102 (long sensing range type) take into account the length of the FT-J8 atmospheric side fiber. Lens (For reflective type fiber) Designation Model No. Pinpoint spot lens Description Pinpoint spot of "0.5 mm "0.020 in. Enables detection of minute objects or small marks. * Distance to focal point: 61 mm 0.236 0.039 in * Applicable fibers: FD-WG4, FD-G4 * Ambient temperature:40 to70 C 40 to158 F FX-MR1 Screw-in depth FX-MR2 Zoom lens For reflective type fiber Distance to focal point Finest spot lens Spot diameter FX-MR3 Distance to focal point Finest spot lens Spot diameter FX-MR6 Screw-in depth Zoom lens Side-view type ( ) FX-MR5 Distance nce to foca al point Spot diameter The spot diameter is adjustable from "0.7 mm to "2 mm "0.028 in to "0.079 in according to how much the fiber is screwed in. * Applicable fibers: FD-WG4, FD-G4 * Ambient temperature:40 to70 C 40 to158 F * Accessory: MS-EX-3 (mounting bracket) Extremely fine spot of "0.3 mm "0.012 in approx. achieved. * Applicable fibers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 * Ambient temperature: 40 to70 C 40 to158 F Extremely fine spot of "0.1 mm "0.004 in approx. achieved. * Applicable fibers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 * Ambient temperature: 20 to60 C 4 to140 F Sensing range for FX-101 (Note) Screw-in depth 7 mm 12 mm 14 mm Distance to focal point 18.5 mm approx. 27 mm approx. 43 mm approx Spot diameter "0.7 mm "1.2 mm "2.0 mm Sensing range for FX-101 (Note) Fiber model No. Distance to focal point FD-EG3 7.50.5 mm FD-EG2 7.50.5 mm FD-EG1 7.50.5 mm FD-WG4/G4/G6X/G6 7.50.5 mm Spot diameter "0.15 mm approx. "0.2 mm approx. "0.3 mm approx. "0.5 mm approx. Sensing range for FX-101 (Note) Fiber model No. Distance to focal point FD-EG3 7.50.5 mm FD-EG2 7.50.5 mm FD-EG1 7.50.5 mm FD-WG4/G4/G6X/G6 7.50.5 mm Spot diameter "0.1 mm approx. "0.15 mm approx. "0.2 mm approx. "0.4 mm approx. FX-MR2 is converted into a side-view type Sensing range for FX-101 (Note) and can be mounted in a very small space. Screw-in depth Distance to focal point Spot diameter * Applicable fibers: FD-WG4, FD-G4 8 mm 13 mm approx. "0.5 mm * Ambient temperature: 10 mm 15 mm approx. "0.8 mm 40 to70 C 40 to158 F 14 mm 30 mm approx "3.0 mm Note: The sensing ranges are the values when used in combination with FX-101 (standard type). Please contact our office for details on sensing ranges for other types of amplifier. 17 FX-100 FIBER OPTIONS Others Model No. FTP-500 (0.5 m 1.640 ft) FTP-1000 (1 m 3.281 ft) Protective tube For thru-beam type fiber ( ) FTP-1500 (1.5 m 4.921 ft) FTP-N500 (0.5 m 1.640 ft) FTP-N1000 (1 m 3.281 ft) FTP-N1500 (1.5 m 4.921 ft) FDP-500 (0.5 m 1.640 ft) FDP-1000 (1 m 3.281 ft) Protective tube For reflective type fiber ( ) FDP-1500 (1.5 m 4.921 ft) FDP-N500 (0.5 m 1.640 ft) FDP-N1000 (1 m 3.281 ft) FDP-N1500 (1.5 m 4.921 ft) Fiber bender FB-1 Universal sensor MS-AJ1-F mounting stand (Note 2) MS-AJ2-F Protective tube Description For M4 thread FT-B8 FT-P80 FT-FM2 FT-P60 FT-FM2S FT-FM2S4 FT-H13-FM2 For M3 thread FT-T80 FT-P40 FT-NFM2 FD-T40 FT-NFM2S FD-P40 FT-NFM2S4 For M6 thread Applicable fibers Designation FD-B8 FD-FM2 FD-FM2S FD-FM2S4 * FTP- * FDP- Fiber bender * FB-1 The protective tube, made of non-corrosive stainless steel, protects the inner FD-P80 fiber cable from any FT-H13-FM2 external forces. FD-T80 FD-NFM2 FD-NFM2S FD-NFM2S4 For M4 thread Fiber cutter * FX-CT2 * FX-CT1 The fiber bender bends the sleeve part of the fiber head at the proper radius. (Note 1) Horizontal mounting type Vertical mounting type Mounting stand assembly for fiber (For M3, M4 or M6 threaded head fiber) Universal sensor mounting stand FX-CT2 Fiber cutter FX-CT1 Attachment for fixed-length fiber FX-AT2 The free-cut type fiber can be easily cut. Accessory. FX-CT1 is attached with the FT-P80 or the FD-P80. The FX-CT2 is provided with fibers other than this. Using the arm which enables adjustment in the horizontal direction, sensing can also be done from above an assembly line. * MS-AJ1-F 360 rotation Forward / back adjustment: 130 mm 5.118 in approx. This is the attachment for the fixed length fiber. Orange. (Accessory) Attachment for "2.2 mm FX-AT3 "0.087 in fiber This is the attachment for the "2.2 mm "0.087 in fiber. Clear Orange. (Accessory. Does not attach with the FT-P80 or the FD-P80.) Attachment for "1 mm FX-AT4 "0.039 in fiber This is the attachment for the "1 mm "0.039 in fiber. Black. (Accessory) Attachment for "1.3 mm FX-AT5 "0.051 in fiber This is the attachment for the "1.3 mm "0.051 in fiber. Gray. (Accessory) Attachment for "1 mm "0.039 in / "1.3 mm FX-AT6 "0.051 in mixed fiber This is the attachment for the "1 mm "0.039 in / "1.3 mm "0.051 in mixed fiber. Black / Gray. (Accessory) Height adjustment: 150 mm 5.906 in approx. 360 rotation 2 20 Mounting hole 20 for M6 screw Angle adjustment:20 * MS-AJ2-F 360 rotation Forward / back adjustment: 130 mm 5.118 in approx. Height adjustment: 150 mm 5.906 in approx. Notes: 1) Do not bend the sleeve part of any side-view type fiber or ultra-small diameter head type fiber. 2) Refer to the `Sensor general catalog 2003-2004' or the SUNX website: http://www.sunx.jp/ for universal sensor mounting stand. 360 rotation Mounting hole 2 20 for M6 screw 20 Angle adjustment:20 Fiber attachment It's possible to simultaneously cut two fibers to the same length Each fiber (with some exceptions) has a newly developed two-in-one fiber attachment (FX-AT3/AT4/AT5/AT6) which enables two fibers to be cut simultaneously to the same length with the new fiber cutter (FX-CT2). Also, since the fibers can be attached to the amplifier while being fixed in position in the two-in-one fiber attachment, sensitivity changes resulting from variation in the amount of fiber insertion do not occur. * FX-AT2 For fixed-length fiber * FX-AT3 For "2.2 mm "0.087 in fiber * FX-AT4 For "1 mm "0.039 in fiber * FX-AT5 For "1.3 mm "0.051 in fiber * FX-AT6 For "1 mm "0.039 in / "1.3 mm "0.051 in mixed fiber PRECAUTIONS FOR PROPER USE * Never use this product as a sensing device for personnel protection. * In case of using sensing devices for personnel protection, use products which meet regulations and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. Part description Operation indicator (Orange) Digital display (Green) (Threshold value) ON key / Set value UP key OFF key / Set value DOWN key MODE key Digital display (Red) (Incident light intensity) 18 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the website: http://www.sunx.jp/ FX-101, FX-102 0.8 0.031 Amplifier 47 1.850 29 1.142 20 12.2 0.787 7 0.480 FX-101(P)-Z, FX-102(P)-Z 6 0.236 6 0.236 2.7 0.106 0 0.7 0.028 OFF key / Setting value DOWN key ON key / Setting value UP key 4.1 Operation indicator (Orange) 0.161 Digital display (Green, Red) MODE key Assembly dimensions with optional protective cover 0.75 0.030 6 6 10.85 0.236 0.236 0.427 47 1.850 1 850 29 1.142 1 142 12.2 0.8 0.480 0.031 0 Amplifier 0.7 0.028 Operation indicator (Orange) 4.1 0.161 Digital display (Green, Red) 9 0.354 2.7 0.106 OFF key / Setting value DOWN key ON key / Setting value UP key MODE key 1 0.039 1.1 0.043 7 0.276 9 0.354 66.2 2.606 2 0.079 2 0.079 7 6 0.236 0.276 1.1 0.043 0.8 0.031 30 10 0.394 1.181 8.1 0.319 3 0.118 10 0.394 "3.2 "0.126 4 0.157 5.5 0.217 MS-DIN-4 5.5 0.217 "6.2 mm "0.244 in spot facing, 3 0.118 deep 5 0.197 Material: PBT 35 1.378 1 378 64.5 2.539 3.2 0.126 End plate (Optional) 7.2 mm 0.283 in spot facing, 4 0.157 deep 2.75 0.108 3 0.118 15 0.591 1 0.039 15 0.591 M3 (Iength 18 mm 0.709 in) pan head screws 60 2.362 6.2 mm 0.244 in spot facing, 3 0.118 deep 3.2 0.126 "3.2 "0.126 3 0.118 1.6 0.063 32 1.260 4 0.157 Suitable for 35mm 1.378 in width DIN rail Material: Polycarbonate CN-14A-C (8) 5.6 M3 Square nut 0.220 24.7 0.972 9 0.354 1 0.039 24.5 0.965 35 1.378 35 (1.378 1 378 ) Suitable for 35 mm 1.378 in width DIN rail MS-DIN-E 11.5 0.453 4 0.157 13.5 0.531 Suitable for 35 mm 1.378 in width DIN rail "3.2 "0.126 9.25 0.364 3.2 8.1 0.126 0.319 2 0 0.079 3 0.118 50 1.969 2 0.0 079 Amplifer mounting bracket (Optional) "7.2 mm "0.283 in spot p facing, g 4 0.157 deep p 10 30 .18 0.3941.181 "3.2 "0.126 3.2 0 0.126 50 1.969 35 1.378 64.5 2.539 13.5 0.531 10 0.394 "6.5 "0.256 4 0.157 Connector attached cable (Optional) L CN-14A-C2 is attached FX-101(P)-CC2 / FX-102(P)-CC2 50 (1.969 1 969) * Length L (8) "3.7 "0.146 cable Model No. CN-14A-C1 CN-14A-C2 CN-14A-C3 CN-14A-C5 Length L (mm in) 1,000 39.370 2,000 78.740 3,000 118.110 5,000 196.850 All information is subject to change without prior notice. SUNX Limited 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-(0)568-33-7211 FAX: +81-(0)568-33-2631 Overseas Sales Dept. http://www.sunx.jp/ Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591 Printed on 100% recycled paper PRINTED IN JAPAN No.CE-FX100-10 January, 2007