SML-P11 Series PICOLEDTM-eco Data Sheet lFeatures lOutline * Ultra compact, thin size 1.0x0.6mm, t=0.2mm * Accomplishes low power consuming application specification assured at IF=1mA lSize V Color Type 1006 (0402) 1006 (0402) 1.0x0.6mm (t=0.2mm) 1.0x0.6mm (t=0.2mm) U D Y M lRecommended Solder Pattern lDimensions Tolerance : 0.05 (unit : mm) (unit : mm) lSpecifications PICOLEDTM -eco Absolute Maximum Ratings (Ta=25C) Part No. Chip Structure Emitting Color Power Forward Reverse Operating Temp. Storage Temp. Dissipation Current Current Voltage PD(mW) IF(mA) IFP(mA) VR(V) Topr(C) Tstg(C) Peak Forward Electrical and Optical Characteristics (Ta=25C) Forward Voltag VF Reverse Current IR Typ. (V) IF Max. VR (mA) (mA) (V) SML-P11VT(R) Red 50 SML-P11DT(R) 20 Orange 621 626 631 1.6 4.0 616 621 626 1.0 2.5 602 605 608 1.8 SML-P11UT(R) AIGaInP on GaAs Dominant Wavelength lD Luminous Intensity IV IF Min. Typ. Min.*2 Typ. Max.*2 IF (nm) (nm) (nm) (mA) (mcd) (mcd) (mA) 100* 1 5 -40 to +85 -40 to +100 1 10 4 52 SML-P11YT(R) Yellow SML-P11MT(R) Yellowish Green 1 7.3 1 4.0 1.9 54 583 586 589 566 569 572 7.6 1.0 2.1 *1 : Duty 1/10, 1kHz *2 : Reference www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 1/7 2016.03 - Rev.C Data Sheet SML-P11 Series lElectrical Characteristics Curves Fig.2 Luminous Intensity Atmosphere Temperature Fig.1 Forward Current - Forward Voltages SML-P11VT SML-P11UT SML-P11DT SML-P11YT SML-P11MT RELATIVE LUMINOUS INTENSITY [a.u.] FORWARD CURRENT : IF [mA] 100.0 Ta=25C 10.0 1.0 0.1 1.5 2.0 2.5 FORWARD VOLTAGE : VF [V] MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Ta=25C 0.8 0.6 0.4 0.2 0 0 5 10 15 20 FORWARD CURRENT : IF [mA] www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 1.4 1.2 1.0 0.8 SML-P11VT SML-P11UT SML-P11DT SML-P11YT SML-P11MT 0.6 0.4 - 40 -20 0 20 40 60 80 100 Fig.4 Derating 1.2 1.0 IF=1mA ATMOSPHERE TEMPERATURE : Ta [C] Fig.3 Luminous Intensity - Forward Current SML-P11VT SML-P11UT SML-P11DT SML-P11YT SML-P11MT 1.6 30 SML-P11VT SML-P11UT SML-P11DT SML-P11YT SML-P11MT 20 10 0 - 40 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE : Ta [C] 2/7 2016.03 - Rev.C Data Sheet SML-P11 Series lSpectrum Data IF=1mA 1.0 INTENSITY [a.u.] SML-P11VT SML-P11UT SML-P11DT SML-P11YT SML-P11MT 0.8 0.6 0.4 0.2 0.0 380 480 580 680 780 WAVELENGTH [nm] * Please take this data as a reference data for the samples are measured randomly. * The data is relativized for each color. It is NOT to show the spectrum peaks are equal. lViewing Angle SCANNING ANGLE (deg) X Y 30 20 0 10 10 20 X' 30 40 Y' 0 10 20 30 50 50 60 70 70 80 80 40 60 70 70 0 10 50 60 60 50 20 40 50 90 100 30 40 50 SML-P11VT SML-P11UT SML-P11DT SML-P11YT SML-P11MT SCANNING ANGLE (deg) 80 80 90 100 90 100 RELATIVE INTENSITY 50 0 90 100 50 RELATIVE INTENSITY lRank Reference of Brightness Red(V,U) Rank Iv (mcd) SML-P11VT SML-P11UT (Ta=25C, IF1mA) A B C D E F G H J K L M N P 0.063 to 0.1 0.1 to 0.16 0.16 to 0.25 0.25 to 0.4 0.4 to 0.63 0.63 to 1.0 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 A B C D E F G H J K L M N P 0.063 to 0.1 0.1 to 0.16 0.16 to 0.25 0.25 to 0.4 0.4 to 0.63 0.63 to 1.0 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 A B C D E F G H J K L M N P 0.063 to 0.1 0.1 to 0.16 0.16 to 0.25 0.25 to 0.4 0.4 to 0.63 0.63 to 1.0 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 A B C D E F G H J K L M N P 0.063 to 0.1 0.1 to 0.16 0.16 to 0.25 0.25 to 0.4 0.4 to 0.63 0.63 to 1.0 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 Orange(D) Rank Iv (mcd) SML-P11DT (Ta=25C, IF1mA) Yellow(Y) Rank Iv (mcd) SML-P11Y T (Ta=25C, IF1mA) Green(M) Rank Iv (mcd) SML-P11MT (Ta=25C, IF1mA) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 3/7 2016.03 - Rev.C Data Sheet SML-P11 Series 4.00 0 . 1 lTaping 0. 1 1 .5 +0 . 1 0 5 .5 0 0 0 . 50 8. 0 0 3 . 50 0 . 0 5 1 .7 5 A 1 . 10 0. 0 5 2 .0 0 0 .0 5 0 .7 0 0 . 0 5 + 0 . 05 0. 2 8 - 0 .0 3 A Enlarged drawing of A" Packaging quantity Pulling Direction +1 0 0 -3 60 18 0 1 1 3 11 . 4 (unit : mm) (Note) Tolerance is 0.1mm, unless otherwise specified. lPart No. Construction lPacking Specification ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags. Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card inside the bag is available upon request. Please contact the nearest sales office or distributer if necessary. www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 4/7 2016.03 - Rev.C SML-P11 Series Data Sheet lPrecaution (Surface Mount Device) 1.Storage If the product is heated during the reflow under the condition of hygroscopic state, it may vaporize and expand which will influence the performance of the product. Therefore, the package is waterproof. Please use the product following the conditions: Using Conditions Classification Temperature Humidity Before using 5 to 30C 30 to 70%RH After opening package 5 to 30C Below 70%RH Expiration Date Remark Within 1 year Storage with waterproof package from Receiving Within 168h Please storing in the airtight container with our desiccant (silica gel) Baking Bake the product in case of below: The expiration date is passed. The color of indicator (silica gel) turned from blue to colorless or from green to pink. (Even if the product is within the expiration date.) Baking Conditions Temperature 603C Remark Time 12 to 24h Humidity Below 20%RH Bake products in reel. Reel and embossed tape are easy to be deformed when baking, so please try not to apply stress on it. Recommend bake once. 2.Application Methods 2-1. Precaution for Drive System and Off Mode Design the circuit without the electric load exceeding the ABSOLUTE MAXIMUM RATING that applies on the products. If drive by constant voltage, it may cause current deviation of the LED and result in deviation of luminous intensity, so we recommend to drive by constant current. (Deviation of VF Value will cause deviation of current in LED.) Furthermore, for off mode, please do not apply voltage neither forward nor reverse. Especially, for the products with the Ag-paste used in the die bonding, there' s high possibility to cause electro migration and result in function failure. 2-2. Operation Life Span There' s possibility for intensity of light drop according to working conditions and environments (applied current, surrounding temperature and humidity, corrosive gases), please call our Sales staffs for inquiries about the concerned application below. Longtime intensity of light life On mode all the time 2-3.Applied Stress on Product The top of the LED is very soft, which the silicon resin is used as sealing resin. Therefore, please pay attention to the overstress on it which may influence its reliability. 2-4.Usage The Product is LED. We are not responsible for the usage as the diode such as Protection Chip, Rectifier, Switching and so on. 3. Others 3-1. Surrounding Gas Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas (ammonia), it may result in low soldering ability (caused by the change in quality of the plating surface ) or optical characteristics changes (light intensity, chrominance) and change in quality of die bonding (Ag-paste) materials. All of the above will cause function failure of the products. Therefore, please pay attention to the storage environment for mounted product (concern the generated gas of the surrounding parts of the products and the atmospheric environment). www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 5/7 2016.03 - Rev.C SML-P11 Series Data Sheet 3-2. Electrostatic Damage The product is part of semiconductor and electrostatic sensitive, there' s high possibility to be damaged by the electrostatic discharge. Please take appropriate measures to avoid the static electricity from human body and earthing of production equipment. The resistance values of electrostatic discharge (actual values) vary with products, therefore, please call our Sales staffs for inquiries. 3-3. Electromagnetic Wave Please concern the influence on LED in case of application with strong electromagnetic wave such as IH (Induction heating). 4.Mounting 4-1. Soldering No resin hardening agent such as filler is used in the sealing resin of the product. Therefore, resin expansion and moisture absorption at humidity will cause heat stress during soldering process and finally has bad influence on the product's reliability. The product is not for flow soldering. Do not expose the product in the environment of high temperature (over 100) or rapid temperature shift (within 3 of temperature gradient) during the flow soldering of surrounding parts. Please set appropriate reflow temperature based on our product usage conditions and specification. The max for reflowing is 2 times, please finish the second flow soldering and flow soldering with other parts within the usage limitation after open the moistureproof package. Compare with N2 reflow, during air reflow, because of the heat and surrounding conditions, it may cause the discoloration of the resin. For our product that has no solder resist, because of its solder amount and soldering conditions, one of its specific characteristics is that solder will penetrate into LED. Thus, there's high possibility that will influence its reliability. Therefore, please be informed, concerning it before using it. 4-2. Automatic Mounting 4-2-1.Silicon Resin Sealing Product The sealing resin of LED is very soft, so please select adsorption nozzle that would not apply stress directly on the sealing section. 4-2-2.Mini Package (Smaller than 1006 size) Vibration may result in low mounting rate since it will cause the static electricity of product and adhere to top cover tape. Therefore, the magnet should be set on parts feeder cassette of the mounter to control the product stabilization. In addition, it is recommended to set ionizer to prevent electrostatic charge. 4-3. Mounting Location The stress like bending stress of circuit board dividing after mounting, may cause LED package crack or damage of LED internal junction, therefore, please concern the mounting direction and position to avoid bending or screwing with great stress of the circuit board.. 4-4. Mechanical Stress after Mounting The mechanical stress may damage the LED after Circuit Mounting, so please pay attention to the touch on product. Stress strength according to the mounting position: A>B>C>D www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 6/7 2016.03 - Rev.C SML-P11 Series Data Sheet 4-5. Soldering Pattern for Recommendation We recommend the soldering pattern that shows on the right. It will be different according to mounting situation of circuit board, therefore, please concern before designing. The product has adopted the electrode structure that it should solder with back electrode of the product. Thus, please be informed that the shape of electrode pin of solder fillet formation is not guaranteed. Reference Mask open area ratio : 80% Mask thickness : 80 to 100m 4-6. Reflow Profile For reflow profile, please refer to the conditions below:() Meaning of marks, Conditions Mark Meanings Tsmax Maximum of pre-heating temperature Tsmin Minimum of pre-heating temperature ts Time from Tsmin to Tsmax TL Reference temperature tL Retention time for TL TP Peak temperature tP Time for peak temperature TR/t Temperature rising rate TD/t Temperature decreasing rate Conditions 180C 140C Over 60sec. 230 to 260C Within 40sec. 260C(Max) Within 10sec. Under 3C/sec. Over -3C/sec. Above conditions are for reference. Therefore, evaluate by customer's own circuit boards and reflow furnaces before using, because stress from circuit boards and temperature variations of reflow furnaces vary by customer's own conditions. 4-7. Cleaning after Soldering Please follow the conditions below if the cleaning is necessary after soldering. Solvent Temperature Ultrasonic Cleaning Drying We recommend to use alcohols solvent such as, isopropyl alcohols Under 30C within 3 minutes 15WBelow 1 liter (capacity of tank) Under 100C within 3 minutes www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. 7/7 2016.03 - Rev.C Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications : 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensur the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. R1102A Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ROHM Semiconductor: SML-P11DTT86 SML-P11UTT86 SML-P11VTT86 SML-P11MTT86 SML-P11YTT86 SML-P11YTT86R SMLP11UTT86R SML-P11MTT86R SML-P11VTT86R SML-P11DTT86R