Product Folder Sample & Buy Support & Community Tools & Software Technical Documents Reference Design LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 LP2980-N Micropower 50-mA Ultra-Low-Dropout Regulator in SOT-23 Package 1 Features 3 Description * * * * * * * * * * * * * * The LP2980-N is a 50-mA, fixed-output voltage regulator designed specifically to meet the requirements of battery-powered applications. 1 2.1-V to 16-V Input Voltage Range 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V Output Versions Ultra-Low-Dropout Voltage Output Voltage Accuracy 0.5% (A Grade) Ensured 50-mA Output Current Requires Only 1-F External Capacitance < 1-A Quiescent Current When Shutdown Low Ground Pin Current at All Load Currents High Peak Current Capability (150 mA Typical) Wide Supply Voltage Range (16 V Maximum) Fast Dynamic Response to Line and Load Low ZOUT Over Wide Frequency Range Overtemperature and Overcurrent Protection -40C to 125C Junction Temperature Range Using an optimized VIP (Vertically Integrated PNP) process, the LP2980-N delivers unequaled performance in all specifications critical to batterypowered designs: Dropout voltage: Typically 120 mV at 50-mA load, and 7 mV at 1-mA load. Ground pin current: Typically 375 A at 50-mA load, and 80 A at 1-mA load. Sleep mode: Less than 1-A quiescent current when ON/OFF pin is pulled to less than 0.18 V. Minimum part count: Requires only a 1-F capacitor on the regulator output. Precision output: Initial output voltage tolerance of 0.5% (A grade). 2 Applications * * * * Cellular Phone Palmtop/Laptop Computer Personal Digital Assistant (PDA) Camcorder, Personal Stereo, Camera 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V versions available as standard products. Device Information(1) PART NUMBER LP2980-N PACKAGE BODY SIZE (NOM) SOT-23 (5) 2.90 mm x 1.60 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Simplified Schematic VIN IN CIN 1 F VOUT OUT COUT 2.2 F LP2980 GND ON/OFF ON/OFF NC Copyright (c) 2016, Texas Instruments Incorporated 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 4 4 4 4 5 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description ............................................ 12 7.1 Overview ................................................................. 12 7.2 Functional Block Diagram ....................................... 12 7.3 Feature Description................................................. 12 7.4 Device Functional Modes........................................ 13 8 Application and Implementation ........................ 14 8.1 Application Information............................................ 14 8.2 Typical Application ................................................. 14 9 Power Supply Recommendations...................... 22 10 Layout................................................................... 22 10.1 Layout Guidelines ................................................. 22 10.2 Layout Example .................................................... 22 11 Device and Documentation Support ................. 23 11.1 11.2 11.3 11.4 11.5 11.6 Device Support...................................................... Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 23 23 23 23 23 23 12 Mechanical, Packaging, and Orderable Information ........................................................... 23 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision O (June 2015) to Revision P Page * Changed minor wording in Description for clarity................................................................................................................... 1 * Deleted input supply voltage (operating) row; deleted "(survival)" from rows of Abs Max table ........................................... 4 * Deleted lead temperature from Abs Max per new format rules.............................................................................................. 4 * Added "(operating") from ROC table; add second row for "Shutdown input voltage" to ROC ............................................... 4 * Added "High K" and footnote 2 to Thermal Information ........................................................................................................ 4 * Changed "...an output tolerance of %..." to "...an initial output voltage tolerance of 0.5%..." ........................................... 12 * Deleted "Very high accuracy 1.23-V reference" .................................................................................................................. 12 * Changed "150 mA" to "50 mA" to correct typo from reformat (2 places) ............................................................................. 12 * Changed "...only 1 A" to "...less than 1 A"........................................................................................................................ 12 * Changed "... pulled low" to "...pulled to less than 0.18 V" ................................................................................................... 12 Changes from Revision N (December 2014) to Revision O Page * Changed pin names VOUT to OUT and VIN to IN per TI nomenclature; correct typos ....................................................... 1 * Changed format of ESD Ratings table .................................................................................................................................. 4 * Deleted (the TO-220 package alone will safely dissipate this) - no TO-220 package for this part ...................................... 20 Changes from Revision M (April 2013) to Revision N * 2 Page Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section; add updated Thermal Information .............................................................................................................................................................. 1 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 Changes from Revision L (April 2013) to Revision M * Page Changed layout of National Semiconductor data sheet to TI format.................................................................................... 22 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 3 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com 5 Pin Configuration and Functions DBV Package 5 Pin SOT-23 Top View Pin Functions PIN NO. NAME I/O 1 IN I 2 GND -- 3 ON/OFF I DESCRIPTION Input voltage Common ground (device substrate) Logic high enable input 4 N/C -- DO NOT CONNECT. Device pin 4 is reserved for post packaging test and calibration of the LP2980-N VOUT accuracy. Device pin 4 must be left floating. Do not connect to any potential. Do not connect to ground. Any attempt to do pin continuity testing on device pin 4 is discouraged. Continuity test results will be variable depending on the actions of the factory calibration. Aggressive pin continuity testing (high voltage, or high current) on device pin 4 may activate the trim circuitry forcing VOUT to move out of tolerance. 5 OUT O Regulated output voltage 4 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 6 Specifications 6.1 Absolute Maximum Ratings (1) (2) MIN MAX UNIT Operating junction temperature -40 125 C Power dissipation (3) Internally Limited Input supply voltage -0.3 16 V Shutdown input voltage -0.3 16 V Output voltage (4) -0.3 9 V IOUT Short-circuit protected Input-output voltage (5) -0.3 16 V Storage temperature, Tstg -65 150 C (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace-specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability and specifications. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, RJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using P(MAX) = ( (TJ(MAX) - TA) / RJA). The value of RJA for the SOT-23 package is 175.7C/W. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2980-N output must be diode-clamped to ground. The output PNP structure contains a diode between the IN and OUT pins that is normally reverse-biased. Reversing the polarity from VIN to VOUT turns on this diode (see Reverse Current Path). 6.2 ESD Ratings VALUE V(ESD) (1) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) All pins except 3 and 4 2000 Pins 3 and 4 1000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) Operating junction temperature Input supply voltage Shutdown input voltage MIN MAX UNIT -40 125 C 2.1 16 0 VIN V 6.4 Thermal Information LP2980-N THERMAL METRIC (1) DBV UNIT 5 PINS RJA Junction-to-ambient thermal resistance, High K (2) RJC(top) Junction-to-case (top) thermal resistance RJB Junction-to-board thermal resistance JT Junction-to-top characterization parameter 2.8 C/W JB Junction-to-board characterization parameter 30.3 C/W (1) (2) 175.7 C/W 78 C/W 30.8 C/W For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics. Thermal resistance value RJA is based on the EIA/JEDEC High-K printed circuit board defined by JESD51-7 - High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 5 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com 6.5 Electrical Characteristics Unless otherwise specified: TJ = 25C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 F, VON/OFF = 2 V. (1) PARAMETER TEST CONDITIONS Output voltage tolerance Output voltage line regulation VIN - VO IGND Dropout voltage (3) Ground pin current MIN TYP VON/OFF ON/OFF input voltage MAX MIN TYP MAX -0.5 0.5 -1 1 -0.75 0.75 -1.5 1.5 1 mA < IL < 50 mA -40C TJ 125C -2.5 2.5 -3.5 3.5 VO(NOM) + 1 V VIN 16 V 0.007 0.014 0.007 0.014 VO(NOM) + 1 V VIN 16 V -40C TJ 125C 0.007 0.032 0.007 0.032 IL = 0 mA 1 3 1 3 IL = 0 mA, -40C TJ 125C 1 5 1 5 IL = 1 mA 7 10 7 10 IL = 1 mA, -40C TJ 125C 7 15 7 15 IL = 10 mA 40 60 40 60 IL = 10 mA, -40C TJ 125C 40 90 40 90 IL = 50 mA 120 150 120 150 IL = 50 mA, -40C TJ 125C 120 225 120 225 IL = 0 mA 65 95 65 95 IL = 0 mA, -40C TJ 125C 65 125 65 125 IL = 1 mA 80 110 80 110 IL = 1 mA, -40C TJ 125C 80 170 80 170 IL = 10 mA 140 220 140 220 IL = 10 mA, -40C TJ 125C 140 460 140 460 IL = 50 mA 375 600 375 600 IL = 50 mA, -40C TJ 125C 375 1200 375 1200 0 1 0 1 VON/OFF < 0.18 V -40C TJ 125C (4) LP2980I-XX (2) 1 mA < IL < 50 mA IL = 1 mA VO LP2980AI-XX (2) High = O/P ON -40C TJ 125C 1.6 1.4 1.6 0.55 0.18 0.55 0.18 VON/OFF = 0 V 0 -1 0 -1 VON/OFF = 5 V -40C TJ 125C 5 15 5 15 IO(PK) Peak output current VOUT VO(NOM) - 5% en Output noise voltage (RMS) BW = 300 Hz to 50 kHz COUT = 10 F VOUT / VIN Ripple rejection f = 1 kHz COUT = 10 F (3) (4) 6 %/V mV A V Low = O/P OFF -40C TJ 125C ON/OFF input current (2) %VNOM 1.4 ION/OFF (1) UNIT 100 150 100 A 150 mA 160 160 V 63 63 dB Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (TJ) range of -40C to +125C, unless otherwise stated. Typical values represent the most likely parametric norm at TA = 25C, and are provided for reference purposes only. Limits are 100% production tested at 25C. Limits over the operating temperature range are ensured through correlation using statistical quality control (SQC) methods. The limits are used to calculate average outgoing quality level (AOQL). Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1-V differential. The ON/OFF inputs must be properly driven to prevent misoperation. For details, see ON/OFF Input Operation. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 Electrical Characteristics (continued) Unless otherwise specified: TJ = 25C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 F, VON/OFF = 2 V.(1) PARAMETER IO(MAX) (5) Short-circuit current TEST CONDITIONS LP2980AI-XX (2) MIN TYP RL = 0 (steady state) (5) 150 LP2980I-XX (2) MAX MIN TYP MAX 150 UNIT mA See related curve(s) in Typical Characteristics section. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 7 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com 6.6 Typical Characteristics Unless otherwise specified: TA = 25C, VIN = VO(NOM) + 1 V, COUT = 2.2 F, all voltage options, ON/OFF pin tied to VIN. Figure 1. Output Voltage vs Temperature Figure 2. Output Voltage vs Temperature Figure 3. Output Voltage vs Temperature Figure 4. Dropout Characteristics Figure 5. Dropout Characteristics 8 Submit Documentation Feedback Figure 6. Dropout Characteristics Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 Typical Characteristics (continued) Unless otherwise specified: TA = 25C, VIN = VO(NOM) + 1 V, COUT = 2.2 F, all voltage options, ON/OFF pin tied to VIN. Figure 7. Dropout Voltage vs Temperature Figure 8. Dropout Voltage vs Load Current Figure 9. Ground Pin Current vs Temperature Figure 10. Ground Pin Current vs Load Current Figure 12. Input Current vs VIN Figure 11. Input Current vs VIN Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 9 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Typical Characteristics (continued) Unless otherwise specified: TA = 25C, VIN = VO(NOM) + 1 V, COUT = 2.2 F, all voltage options, ON/OFF pin tied to VIN. 10 Figure 13. Line Transient Response Figure 14. Line Transient Response Figure 15. Load Transient Response Figure 16. Load Transient Response Figure 17. Load Transient Response Figure 18. Load Transient Response Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 Typical Characteristics (continued) Unless otherwise specified: TA = 25C, VIN = VO(NOM) + 1 V, COUT = 2.2 F, all voltage options, ON/OFF pin tied to VIN. Figure 19. Short Circuit Current Figure 20. Instantaneous Short Circuit Current vs Temperature Figure 21. Short Circuit Current Figure 22. Output Impedance vs Frequency Figure 23. Output Impedance vs Frequency Figure 24. Output Noise Density Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 11 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Typical Characteristics (continued) Unless otherwise specified: TA = 25C, VIN = VO(NOM) + 1 V, COUT = 2.2 F, all voltage options, ON/OFF pin tied to VIN. 12 Figure 25. Ripple Rejection Figure 26. Input to Output Leakage vs Temperature Figure 27. Output Reverse Leakage vs Temperature Figure 28. Turnon Waveform Figure 29. Turnoff Waveform Figure 30. ON/OFF Pin Current vs VON/OFF Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 7 Detailed Description 7.1 Overview The LP2980-N is a 50-mA, fixed-output voltage regulator designed specifically to meet the requirements of battery-powered applications. Available in output voltages from 2.5 V to 5 V, the device has an initial output voltage tolerance of 0.5% for the A grade (1% for the non-A version). Using an optimized vertically integrated PNP (VIP) process, the LP2980-N contains these features to facilitate battery-powered designs: * Fixed 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V output versions * Low-dropout voltage, typical dropout of 120 mV at 50-mA load current and 7 mV at 1-mA load * Low ground current, typically 370 A at 50-mA load and 80 A at 1-mA load * A sleep mode feature is available, allowing the regulator to consume less than 1 A typically when the ON/OFF pin is pulled to less than 0.18 V. * Overtemperature protection and overcurrent protection circuitry is designed to safeguard the device during unexpected conditions. 7.2 Functional Block Diagram 7.3 Feature Description 7.3.1 Multiple Voltage Options To meet the different application requirements, the LP2980-N provides multiple fixed output options from 2.5 V to 5 V. 7.3.2 High-Accuracy Output Voltage With special careful design to minimize all contributions to the output voltage error, the LP2980-N distinguishes itself as a very high-accuracy output voltage micropower LDO. This includes a tight initial tolerance (0.5% typical), extremely good line regulation (0.007%/V typical), and a very low output voltage temperature coefficient, making the part an ideal low-power voltage reference. 7.3.3 Ultra-Low-Dropout Voltage Generally speaking, the dropout voltage often refers to the voltage difference between the input and output voltage (VDO = VIN - VOUT), where the main current pass-FET is fully on in the ohmic region of operation and is characterized by the classic RDS(ON) of the FET. VDO indirectly specifies a minimum input voltage above the nominal programmed output voltage at which the output voltage is expected to remain within its accuracy boundary. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 13 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Feature Description (continued) 7.3.4 Low Ground Current LP2980-N uses a vertical PNP process which allows for quiescent currents that are considerably lower than those associated with traditional lateral PNP regulators, typically 370 A at 150-mA load and 80 A at 1-mA load. 7.3.5 Sleep Mode When pulling the ON/OFF pin to low level, LP2980-N enters sleep mode, and less than 1-A quiescent current is consumed. This function is designed for the application which needs a sleep mode to effectively enhance battery life cycle. 7.3.6 Short-Circuit Protection (Current Limit) The internal current-limit circuit is used to protect the LDO against high-load current faults or shorting events. The LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources constant current. Therefore, the output voltage falls when load impedance decreases. If a current limit occurs and the resulting output voltage is low, excessive power may be dissipated across the LDO resulting in a thermal shutdown of the output. A foldback feature limits the short-circuit current to protect the regulator from damage under all load conditions. If OUT is forced below 0 V before EN goes high and the load current required exceeds the foldback current limit, the device may not start up correctly. 7.3.7 Thermal Protection The LP2980-N contains a thermal shutdown protection circuit to turn off the output current when excessive heat is dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The internal protection circuitry of the LM2980-N is designed to protect against thermal overload conditions. The circuitry is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown degrades its reliability. 7.4 Device Functional Modes 7.4.1 Operation with VOUT(TARGET) + 1 V VIN < 16 V The device operates if the input voltage is equal to, or exceeds, VOUT(TARGET) + 0.6 V. At input voltages below the minimum VIN requirement, the device does not operate correctly and output voltage may not reach target value. 7.4.2 Operation With ON/OFF Control If the voltage on the ON/OFF pin is less than 0.18 V, the device is disabled, and the shutdown current does not exceed 1 A. Raising ON/OFF above 1.6 V initiates the start-up sequence of the device. 14 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LP2980-N is a linear voltage regulator operating from 2.1 V to 16 V on the input and regulates voltages between 2.5 V to 5 V with 0.5% accuracy and 50-mA maximum output current. Efficiency is defined by the ratio of output voltage to input voltage because the LP2980-N is a linear voltage regulator. To achieve high efficiency, the dropout voltage (VIN - VOUT) must be as small as possible, thus requiring a very-low-dropout LDO. Successfully implementing an LDO in an application depends on the application requirements. If the requirements are simply input voltage and output voltage, compliance specifications (such as internal power dissipation or stability) must be verified to ensure a solid design. If timing, startup, noise, power supply rejection ratio (PSRR), or any other transient specification is required, then the design becomes more challenging. This section discusses the implementation and behavior of the LP2980-N LDO. 8.2 Typical Application *ON/OFF input must be actively terminated. Tie to IN if this function is not to be used. **Minimum output capacitance is 1 F to ensure stability over full load current range. More capacitance provides superior dynamic performance and additional stability margin (see Output Capacitor Recommendation). ***Do not make connections to this pin. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 15 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Typical Application (continued) 8.2.1 Design Requirements PARAMETER DESIGN REQUIREMENT Input voltage 5 V 10%, provided by the DC-DC converter switching at 1 MHz Output voltage 3.3 V 5% Output current 50 mA (maximum), 1 mA (minimum) RMS noise, 300 Hz to 50 kHz < 1 mVRMS PSRR at 1 kHz > 40 dB 8.2.2 Detailed Design Procedure At 50-mA loading, the dropout of the LP2980-N has 225-mV maximum dropout over temperature, thus an 1700mV headroom is sufficient for operation over both input and output voltage accuracy. The efficiency of the LP2980-N in this configuration is VOUT / VIN = 66.7%. To achieve the smallest form factor, the SOT-23 package is selected. Input and output capacitors are selected in accordance with the Output Capacitor Recommendation section. With an efficiency of 66.7% and a 50-mA maximum load, the internal power dissipation is 85 mW, which corresponds to a 14.9C junction temperature rise for the SOT-23 package. With an 85C maximum ambient temperature, the junction temperature is at 99.9C. 8.2.2.1 Output Capacitor Recommendation Like any low-dropout regulator, the LP2980-N requires an output capacitor to maintain regulator loop stability. This capacitor must be selected to meet the requirements of minimum capacitance and equivalent series resistance (ESR) range. It is not difficult to find capacitors which meet the criteria of the LP2980-N, as the acceptable capacitance and ESR ranges are wider than for most other LDOs. In general, the capacitor value must be at least 1 F (over the actual ambient operating temperature), and the ESR must be within the range indicated in Figure 31, Figure 32, and Figure 33. It should be noted that, although a maximum ESR is shown in these figures, it is very unlikely to find a capacitor with an ESR that high. 8.2.2.1.1 Tantalum Capacitors Surface-mountable solid tantalum capacitors offer a good combination of small physical size for the capacitance value, and an ESR in the range needed by the LP2980-N. The results of testing the LP2980-N stability with surface-mount solid tantalum capacitors show good stability with values of at least 1 F. The value can be increased to 2.2 F (or more) for even better performance, including transient response and noise. Small value tantalum capacitors that have been verified as suitable for use with the LP2980-N are shown in Table 1. Capacitance values can be increased without limit. 8.2.2.1.2 Aluminum Electrolytic Capacitors Although probably not a good choice for a production design, because of relatively large physical size, an aluminum electrolytic capacitor can be used in the design prototype for an LP2980-N regulator. A value of at least 1 F should be used, and the ESR must meet the conditions of Figure 31, Figure 32, and Figure 33. If the operating temperature drops below 0C, the regulator may not remain stable, as the ESR of the aluminum electrolytic capacitor will increase and may exceed the limits indicated in Figure 31, Figure 32, and Figure 33. Table 1. Surface-Mount Tantalum Capacitor Selection Guide 1-F SURFACE-MOUNT TANTALUM CAPACITORS 16 MANUFACTURER PART NUMBER Kemet T491A105M010AS NEC NRU105M10 Siemens B45196-E3105-K Nichicon F931C105MA Sprague 293D105X0016A2T Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 2.2-F SURFACE-MOUNT TANTALUM CAPACITORS MANUFACTURER PART NUMBER Kemet T491A225M010AS NEC NRU225M06 Siemens B45196/2.2/10/10 Nichicon F930J225MA Sprague 293D225X0010A2T 8.2.2.1.3 Multilayer Ceramic Capacitors Surface-mountable multilayer ceramic capacitors may be an attractive choice because of their relatively small physical size and excellent RF characteristics. However, they sometimes have ESR values lower than the minimum required by the LP2980-N, and relatively large capacitance change with temperature. The manufacturer's data sheet for the capacitor should be consulted before selecting a value. Test results of LP2980-N stability using multilayer ceramic capacitors show that a minimum value of 2.2 F is usually needed for the 5-V regulator. For the lower output voltages, or for better performance, a higher value should be used, such as 4.7 F. Multilayer ceramic capacitors that have been verified as suitable for use with the LP2980-N are shown in Table 2. Table 2. Surface-Mount Multilayer Ceramic Capacitor Selection Guide 2.2-F SURFACE-MOUNT CERAMIC MANUFACTURER PART NUMBER Tokin 1E225ZY5U-C203 Murata GRM42-6Y5V225Z16 4.7-F SURFACE-MOUNT CERAMIC MANUFACTURER PART NUMBER Tokin 1E475ZY5U-C304 Figure 31. 1-F ESR Range Figure 32. 2.2-F ESR Range Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 17 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Figure 33. 10-F ESR Range 8.2.2.2 Reverse Current Path The internal PNP power transistor used as the pass element in the LP2980-N has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reverse biased (see Figure 34). VIN VOUT PNP GND Figure 34. LP2980-N Reverse Current Path However, if the input voltage is more than a VBE below the output voltage, this diode will turn on and current will flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into the VIN pin and out the ground pin, which can damage the part. The internal diode can also be turned on if the input voltage is abruptly stepped down to a voltage which is a VBE below the output voltage. In any application where the output voltage may be higher than the input voltage, an external Schottky diode must be connected from VIN to VOUT (cathode on VIN, anode on VOUT, see Figure 35), to limit the reverse voltage across the LP2980-N to 0.3 V (see Absolute Maximum Ratings). 18 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 SCHOTTKY DIODE VIN VOUT PNP GND Figure 35. Adding External Schottky Diode Protection 8.2.2.3 ON/OFF Input Operation The LP2980-N is shut off by pulling the ON/OFF input low, and turned on by driving the input high. If this feature is not to be used, the ON/OFF input must be tied to IN to keep the regulator on at all times (the ON/OFF input must not be left floating). To ensure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and below the specified turn-on and turn-off voltage thresholds which ensure an ON or OFF state (see Electrical Characteristics). The ON/OFF signal may come from either a totem-pole output, or an open-collector output with a pull-up resistor to the LP2980-N input voltage or another logic supply. The high-level voltage may exceed the LP2980-N input voltage, but must remain within the absolute maximum ratings for the ON/OFF pin. It is also important that the turn-on and turn-off voltage signals applied to the ON/OFF input have a slew rate that is greater than 40 mV/s. NOTE The regulator shutdown function will not operate correctly if a slow-moving signal is used to drive the ON/OFF input. 8.2.2.4 Increasing Output Current The LP2980-N can be used to control higher-current regulators, by adding an external PNP pass transistor. With the PNP transistors shown in Figure 36, the output current can be as high as 400 mA, as long as the input voltage is held within the Safe Operation Boundary Curves shown below in Figure 37. To ensure regulation, the minimum input voltage of this regulator is 6 V. This headroom is the sum of the VBE of the external transistor and the dropout voltage of the LP2980-N. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 19 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com Figure 36. 5-V and 400-mA Regulator Notes: Note A: Drive this input with a logic signal (see ON/OFF Input Operation). If the shutdown function is not to be used, tie the ON/OFF pin directly to the IN pin. Note B: Recommended devices (other PNP transistors can be used if the current gain and voltage ratings are similar). Note C: Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit. Note D: Increasing the output capacitance improves transient response and increases phase margin. Note E: Maximum safe input voltage and load current are limited by power dissipation in the PNP pass transistor and the maximum ambient temperature for the specific application. If a TO-92 transistor such as the MPS2907A is used, the thermal resistance from junction-to-ambient is 180C/W in still air. Assuming a maximum allowable junction temperature of 150C for the MPS2907A device, the following curves show the maximum VIN and IL values that may be safely used for several ambient temperatures. Figure 37. Safe Operation Boundary Curves for Figure 36 With limited input voltage range, the LP2980-N can control a 3.3-V, 3-A regulator with the use of a high currentgain external PNP pass transistor as shown in Figure 38. If the regulator is to be loaded with the full 3 A, heat sinking will be required on the pass transistor to keep it within its rated temperature range. See Figure 39. For best load regulation at the high load current, the LP2980-N output voltage connection should be made as close to the load as possible. 20 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 Although this regulator can handle a much higher load current than can the LP2980-N alone, it can be shut down in the same manner as the LP2980-N. When the ON/OFF control is brought low, the converter will be in shutdown, and will draw less than 1 A from the source. Figure 38. 5 V to 3.3 V at 3-A Converter NOTES: Note A: Drive this input with a logic signal (see ON/OFF Input Operation). If the shutdown function is not to be used, tie the ON/OFF pin directly to the IN pin. Note B: Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit. Note C: Increasing the output capacitance improves transient response and increases phase margin. Note D: A heatsink may be required for this transistor. The maximum allowable value for thermal resistance of the heatsink is dependent on ambient temperature and load current (see curves in Figure 39). Once the value is obtained from the graph, a heatsink must be selected which has a thermal resistance equal to or lower than this value. If the value is above 60C/W, no heatsink is required. For these curves, a maximum junction temperature of 150C is assumed for the pass transistor. The case-toheatsink attachment thermal resistance is assumed to be 1.5C/W. All calculations are for 5.5-V input voltage (which is worst-case for power dissipation). Figure 39. Heatsink Thermal Resistance Requirements for Figure 38 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 21 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com 8.2.3 Application Curve Figure 40. Load Transient Response 22 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 9 Power Supply Recommendations The LP2980-N is designed to operate from an input voltage supply range between 2.1 V and 16 V. The input voltage range provides adequate headroom for the device to have a regulated output. This input supply must be well regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the output noise performance. 10 Layout 10.1 Layout Guidelines For best overall performance, place all circuit components on the same side of the circuit board and as near as practical to the respective LDO pin connections. Place ground return connections to the input and output capacitors, and to the LDO ground pin as close as possible to each other, connected by a wide, component-side, copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and thereby reduces load-current transients, minimizes noise, and increases circuit stability. A ground reference plane is also recommended and is either embedded in the PCB itself or located on the bottom side of the PCB opposite the components. This reference plane serves to assure accuracy of the output voltage, shield noise, and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In most applications, this ground plane is necessary to meet thermal requirements. 10.2 Layout Example VIN VOUT Input Capacitor IN GND OUT Output Capacitor Ground ON/OFF ON/OFF NC Figure 41. LP2980-N Layout Example Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N 23 LP2980-N SNOS733P - APRIL 2000 - REVISED SEPTEMBER 2016 www.ti.com 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.2 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 24 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LP2980-N PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP2980AIM5-2.5 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0NA LP2980AIM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NA LP2980AIM5-3.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L02A LP2980AIM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02A LP2980AIM5-3.3 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L00A LP2980AIM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00A LP2980AIM5-4.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L37A LP2980AIM5-5.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L01A LP2980AIM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01A LP2980AIM5X-2.5 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L0NA LP2980AIM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NA LP2980AIM5X-3.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L02A LP2980AIM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02A LP2980AIM5X-3.3 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L00A LP2980AIM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00A LP2980AIM5X-4.7/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L37A LP2980AIM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01A LP2980IM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NB LP2980IM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02B LP2980IM5-3.3 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L00B Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP2980IM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00B LP2980IM5-3.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L21B LP2980IM5-4.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L37B LP2980IM5-5.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L01B LP2980IM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01B LP2980IM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NB LP2980IM5X-3.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L02B LP2980IM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02B LP2980IM5X-3.3 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L00B LP2980IM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00B LP2980IM5X-5.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L01B LP2980IM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 14-Oct-2017 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ B0 (mm) K0 (mm) P1 (mm) LP2980AIM5-2.5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 LP2980AIM5-3.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 LP2980AIM5-3.0/NOPB SOT-23 DBV 5 1000 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 LP2980AIM5-3.3 SOT-23 DBV 5 Q3 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5-3.3/NOPB SOT-23 DBV LP2980AIM5-4.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 LP2980AIM5-5.0 SOT-23 Q3 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5-5.0/NOPB LP2980AIM5X-2.5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-4.7/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-3.0 LP2980AIM5X-3.3 LP2980IM5-2.5/NOPB SOT-23 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LP2980IM5-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 LP2980IM5-3.3 SOT-23 DBV 5 1000 178.0 8.4 LP2980IM5-3.3/NOPB SOT-23 DBV 5 1000 178.0 LP2980IM5-3.8/NOPB SOT-23 DBV 5 1000 178.0 LP2980IM5-4.7/NOPB SOT-23 DBV 5 1000 W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-5.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-5.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-5.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2980AIM5-2.5 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-3.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2980AIM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-4.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5X-2.5 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.3 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-4.7/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-4.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.3 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-5.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 3 PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LP2980AIM5-2.5 LP2980AIM5-2.5/NOPB LP2980AIM5-3.0 LP2980AIM5-3.0/NOPB LP2980AIM5-3.3 LP2980AIM53.3/NOPB LP2980AIM5-4.7/NOPB LP2980AIM5-5.0 LP2980AIM5-5.0/NOPB LP2980AIM5X-2.5 LP2980AIM5X2.5/NOPB LP2980AIM5X-3.0 LP2980AIM5X-3.0/NOPB LP2980AIM5X-3.3 LP2980AIM5X-3.3/NOPB LP2980AIM5X4.7 LP2980AIM5X-4.7/NOPB LP2980AIM5X-5.0 LP2980AIM5X-5.0/NOPB LP2980IM5-2.5/NOPB LP2980IM5-3.0 LP2980IM5-3.0/NOPB LP2980IM5-3.3 LP2980IM5-3.3/NOPB LP2980IM5-3.8/NOPB LP2980IM5-4.7/NOPB LP2980IM5-5.0 LP2980IM5-5.0/NOPB LP2980IM5X-2.5 LP2980IM5X-2.5/NOPB LP2980IM5X-3.0 LP2980IM5X3.0/NOPB LP2980IM5X-3.3 LP2980IM5X-3.3/NOPB LP2980IM5X-4.7/NOPB LP2980IM5X-5.0 LP2980IM5X5.0/NOPB