57
11.08
D
WIMA MKS 4
Metallized Polyester (PET) Capacitors
PCM 7.5 mm to 37.5 mm
Special Features Electrical Data
Capacitance range:
1000 pF to 220 mF (E12-values on request)
Rated voltages:
50 VDC, 63 VDC, 100 VDC, 250 VDC, 400 VDC,
630 VDC, 1000 VDC, 1500 VDC, 2000 VDC
Capacitance tolerances:
± 20%, ± 10% ± 5%
Operating temperature range:
–55+ C to +100+ C
Climatic test category:
55/100/56 in accordance with IEC
Insulation resistance at +20+ C:
Ur Utest C 0.33 mF 0.33 mF < C 220 mF
50 VDC 10 V 5 x 103 M¸ (mean value: 3 x 104 M¸) 1500 sec (M¸ x mF) (mean value: 4500 sec)
63 VDC 50 V 1 x 104 M¸ (mean value: 5 x 104 M¸) 3000 sec (M¸ x mF) (mean value: 6000 sec)
100 VDC 100 V 1.5 x 104 M¸ (mean value: 5 x 104 M¸) 5000 sec (M¸ x mF) (mean value: 15000 sec)
250 VDC 100 V 3 x 104 M¸ (mean value: 1 x 105 M¸) 10 000 sec (M¸ x mF) (mean value: 40 000 sec)
Measuring time: 1 min.
Dissipation factors at + 20) C: tan d
at f C 0.1 mF 0.1 mF < C 1.0 mF C > 1.0 mF
1 kHz 8 x 10-3 8 x 10-3 10 x 10-3
10 kHz 15 x 10-3 15 x 10-3 –
100 kHz 30 x 10-3 – –
Maximum pulse rise time:
Capacitance Pulse rise time V/msec
pF/mF max. operation/test
50VDC 63VDC 100VDC 250VDC 400VDC 630VDC 1000VDC 1500VDC 2000VDC
1000 ... 6800 – – – – – – 70/700 90/900
100
/
1000
0.01 ... 0.022 – 30/300 30/300 35/350 38/380 40/400 50/500 50/500 60/600
0.033 ... 0.068 – 15/150 15/150 20/200 25/250 32/320 26/260 35/350 40/400
0.1 ... 0.22 10/100 10/100 12/120 15/150 15/150 17/170 20/200 35/350 40/400
0.33 ... 0.68 9/90 9/90 9/90 10/100 10/100 13/130 20/200 20/200 38/380
1.0 ... 2.2 6/60 6/60 5/50 6/60 9/90 13/130 14/140 15/150 –
3.3 ... 6.8 2.5/25 3/30 3/30 6/60 6/60 9/90 12/120 – –
10 ... 220 2.5/25 2.5/25 2.5/25 3/30 6/60 – – – –
for pulses equal to the rated voltage
Test voltage: 1.6 Ur, 2 sec.
Test specifications:
In accordance with IEC 60384-2
and EN 130 400
Voltage derating:
A voltage derating factor of 1.25 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages.
Reliability:
Operational life 300 000 hours
Failure rate 2 fit (0.5 x Ur and 40) C)
Mechanical Tests
Pull test on leads:
d 0.8 l: 10 N in direction of leads
d > 0.8 l: 20 N in direction of leads
according to IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test: 4000 bumps at 390 m/sec2
in accordance with IEC 60068-2-29
Packing
Available taped and reeled up to and
including case size 15 x 26 x 31.5 /
PCM 27.5 mm.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
˜ High volume/capacitance ratio
˜ Self-healing
˜ According to RoHS 2002/95/EC
Typical Applications
For general DC-applications e.g.
˜ By-pass
˜ Blocking
˜ Coupling and decoupling
˜ Timing
Construction
Dielectric:
Polyethylene-terephthalate (PET) film
Capacitor electrodes:
Vacuum-deposited
Internal construction:
MKS 4: 30 VAC, 40 VAC, 63 VAC, 160 VAC, 200 VAC
MKS 4: 400 VAC
Plastic film
Vacuum-deposited
electrode
Metal contact layer
(schoopage)
Terminating wire
Plastic film
Vacuum-deposited
electrode
Metal contact layer
(schoopage)
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations:
Tinned wire.
Marking:
Colour: Red. Marking: Black.
Epoxy resin seal: Red
58
11.08
WIMA FKP 4
Continuation
General Data
D
Capac-
itance
50 VDC/30 VAC*63 VDC/40 VAC*100 VDC/63 VAC*250 VDC/160 VAC*400 VDC/200 VAC*
W H L PCM
** W H L PCM
** W H L PCM
** W H L PCM
** W H L PCM
**
0.01 mF2.5 7 10 7.5*2.5 7 10 7.5*3 8.5 10 7.5*3 8.5 10 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*4 9 13 10*
0.015 „ 2.5 7 10 7.5*2.5 7 10 7.5*3 8.5 10 7.5*3 8.5 10 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*4 9 13 10*
0.022 „ 2.5 7 10 7.5*2.5 7 10 7.5*3 8.5 10 7.5*4 9 10 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*4 9 13 10*
0.033 „ 2.5 7 10 7.5*2.5 7 10 7 .5*3 8.5 10 7.5*4 9 10 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*4 9 13 10*
0.047 „ 2.5 7 10 7.5*2.5 7 10 7.5*3 8.5 10 7.5*5 10.5 10.3 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*4 9 13 10*
0.068 „ 2.5 7 10 7.5*2.5 7 10 7.5*4 9 10 7.5*5 10.5 10.3 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*4 9 13 10*
0.1 mF2.5 7 10 7.5 2.5 7 10 7.5*2.5 7 10 7.5*4 9 10 7.5*5 10.5 10.3 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*5 11 13 10*
0.15 „ 2.5 7 10 7.5 2.5 7 10 7.5*3 8.5 10 7.5*5 10.5 10.3 7.5*5.7 12.5 10.3 7.5*
4 9 13 10*4 9 13 10*4 9 13 10*6 12 13 10*
0.22 „ 2.5 7 10 7.5 3 8.5 10 7.5*3 8.5 10 7.5*5 10.5 10.3 7.5*6 12 13 10*
4 9 13 10*4 9 13 10*5 11 13 10*6 12.5 18 15*
0.33 „ 2.5 7 10 7.5 4 9 10 7.5*4 9 10 7.5*5.7 12.5 10.3 7.5*8 15 18 15
4 9 13 10*4 9 13 10*5 11 13 10*
0.47 „ 3 8.5 10 7.5 4 9 10 7.5*4.5 9.5 10.3 7.5*6 12 13 10*8 15 18 15*
4 9 13 10*4 9 13 10*6 12.5 18 15*6 15 26.5 22.5*
0.68 " 4 9 10 7.5 5 10.5 10.3 7.5*5 10.5 10.3 7.5*7 14 18 15 7 16.5 26.5 22.5
4 9 13 10*4 9 13 10*
1.0 mF4 9 10 7.5 5 10.5 10.3 7.5*5.7 12.5 10.3 7.5*8 15 18 15*10.5 19 26.5 22.5*
4 9 13 10*5 11 13 10*6 15 26.5 22.5*11 21 31.5 27.5*
1.5 „ 5 10.5 10.3 7.5 5.7 12.5 10.3 7.5*6 12 13 10*9 16 18 15*11 21 26.5 22.5*
5 11 13 10*7 14 18 15*7 16.5 26.5 22.5*11 21 31.5 27.5*
2.2 „ 5.7 12.5 10.3 7.5 5 11 13 10*8 15 18 15*10.5 19 26.5 22.5*11 21 31.5 27.5
6 12.5 18 15*6 15 26.5 22.5*9 19 31.5 27.5*
3.3 „ 5.7 12.5 10.3 7.5 6 12 13 10*9 16 18 15*11 21 26.5 22.5*13 24 31.5 27.5
7 14 18 15*7 16.5 26.5 22.5*11 21 31.5 27.5*
4.7 „ 7.2 12.5 10.3 7.5*7 14 18 15*10.5 19 26.5 22.5*11 21 31.5 27.5 17 29 31.5 27.5
6 12 13 10*6 15 26.5 22.5*9 19 31.5 27.5*
6.8 „ 7.2 12.5 10.3 7.5*8 15 18 15*10.5 19 26.5 22.5*13 24 31.5 27.5 17 34.5 31.5 27.5*
6 12 13 10*7 16.5 26.5 22.5*11 21 31.5 27.5*15 26 41.5 37.5*
10 mF9 16 18 15 8.5 18.5 26.5 22.5*13 24 31.5 27.5 17 29 31.5 27.5 19 32 41.5 37.5
11 21 31.5 27.5*
15 „ 11 21 26.5 22.5 11 21 26.5 22.5*13 24 31.5 27.5 17 34.5 31.5 27.5*20 39.5 41.5 37.5
11 21 31.5 27.5*17 29 41.5 37.5*
22 „ 11 21 31.5 27.5 13 24 31.5 27.5 15 26 31.5 27.5 19 32 41.5 37.5
33 „ 13 24 31.5 27.5 15 26 31.5 27.5 17 29 31.5 27.5*24 45.5 41.5 37.5
13 24 41.5 37.5*
47 „ 15 26 31.5 27.5*17 29 31.5 27.5*17 29 41.5 37.5
13 24 41.5 37.5*17 29 41.5 37.5*
68 „ 20 39.5 31.5 27.5*20 39.5 31.5 27.5*20 39.5 41.5 37.5
17 29 41.5 37.5*19 32 41.5 37.5*
100 mF19 32 41.5 37.5 20 39.5 41.5 37.5 24 45.5 41.5 37.5
150 „ 20 39.5 41.5 37.5 24 45.5 41.5 37.5
220 „ 24 45.5 41.5 37.5
* AC voltage: f 50 Hz; 1.4 x Urms + UDC Ur
** PCM = Printed circuit module = lead spacing
* On ordering please state the required PCM (lead spacing)!
If not specified, smaller PCM will be booked.
Dims. in mm.
Taped version see page 121.
Rights reserved to amend design data without prior notification.
WIMA MKS 4
Continuation page 59
PCM
at the lead exit
points
( 0.4)
L
W
H
d
6 -2
P d PCM W
0.5 7.5 3
0.6 7.5 4
0.6 10
0.8 15 - 27.5
1.0 37.5
59
11.08
Continuation
General Data
D
WIMA MKS 4
Capacitance 630 VDC/400 VAC*1000 VDC/400 VAC*1500 VDC/400 VAC*2000 VDC/400 VAC*
W H L PCM
** W H L PCM
** W H L PCM
** W H L PCM
**
1000 pF 3 8.5 10 7.5*4 9 13 10 4 9 13 10
4 9 13 10*
1500 „ 3 8.5 10 7.5*4 9 13 10 4 9 13 10
4 9 13 10*
2200 „ 3 8.5 10 7.5*4 9 13 10 5 11 13 10
4 9 13 10*
3300 „ 4 9 10 7.5*4 9 13 10 6 12 13 10*
4 9 13 10*5 11 18 15*
4700 „ 4 9 10 7.5*4 9 13 10*5 11 18 15
4 9 13 10*5 11 18 15*
6800 „ 4.5 9.5 10.3 7.5*5 11 13 10*6 12.5 18 15
4 9 13 10*5 11 18 15*
0.01 mF 3 8.5 10 7.5** 5 10.5 10.3 7.5*6 12 13 10*7 14 18 15*
4 9 13 10*5 11 13 10*5 11 18 15*6 15 26.5 22.5*
0.015 „ 4 9 10 7.5** 5.7 12.5 10.3 7.5*6 12.5 18 15 6 15 26.5 22.5
4 9 13 10*6 12 13 10*
0.022 „ 4.5 9.5 10.3 7.5** 5 11 18 15 7 14 18 15*7 16.5 26.5 22.5
4 9 13 10*6 15 26.5 22.5*
0.033 „ 5 10.5 10.3 7.5** 6 12.5 18 15*8 15 18 15*10.5 19 26.5 22.5
5 11 13 10*6 15 26.5 22.5*6 15 26.5 22.5*
0.047 „ 5.7 12.5 10.3 7.5** 7 14 18 15*7 16.5 26.5 22.5 11 21 26.5 22.5*
6 12 13 10*6 15 26.5 22.5*11 21 31.5 27.5*
0.068 „ 6 12 13 10*8 15 18 15*8.5 18.5 26.5 22.5 11 21 31.5 27.5
5 11 18 15*6 15 26.5 22.5*
0.1 mF 6 12.5 18 15*9 16 18 15*10.5 19 26.5 22.5*13 24 31.5 27.5
6 15 26.5 22.5*7 16.5 26.5 22.5* 9 19 31.5 27.5*
0.15 „ 7 14 18 15*8.5 18.5 26.5 22.5 11 21 31.5 27.5 17 29 31.5 27.5*
6 15 26.5 22.5*13 24 41.5 37.5*
0.22 „ 8 15 18 15*10.5 19 26.5 22.5 13 24 31.5 27.5 17 29 41.5 37.5
6 15 26.5 22.5*
0.33 „ 7 16.5 26.5 22.5*11 21 26.5 22.5*17 34.5 31.5 27.5*20 39.5 41.5 37.5
9 19 31.5 27.5*11 21 31.5 27.5*17 29 41.5 37.5*
0.47 „ 10.5 19 26.5 22.5*13 24 31.5 27.5 20 39.5 31.5 27.5*24 45.5 41.5 37.5
9 19 31.5 27.5*17 29 41.5 37.5*
0.68 „ 11 21 26.5 22.5*15 26 31.5 27.5 20 39.5 41.5 37.5
11 21 31.5 27.5*
1.0 mF 11 21 31.5 27.5 17 29 31.5 27.5*24 45.5 41.5 37.5
17 29 41.5 37.5*
1.5 „ 15 26 31.5 27.5 19 32 41.5 37.5
2.2 „ 17 34.5 31.5 27.5*20 39.5 41.5 37.5
15 26 41.5 37.5*
3.3 „ 20 39.5 31.5 27.5*24 45.5 41.5 37.5
19 32 41.5 37.5*
4.7 „ 20 39.5 41.5 37.5
6.8 „ 24 45.5 41.5 37.5
* AC voltage: f 50 Hz; 1.4 x Urms + UDC Ur
** PCM = Printed circuit module = lead spacing
* On ordering please state the required PCM (lead spacing)!
If not specified, smaller PCM will be booked.
** Admissible AC voltage 250 VAC max.
Dims. in mm.
Taped version see page 121.
Rights reserved to amend design data without prior notification.
PCM
at the lead exit
points
( 0.4)
L
W
H
d
6 -
2
AC voltage graphs see page 66
P d PCM W
0.5 7.5 3
0.6 7.5 4
0.6 10
0.8 15 - 27.5
1.0 37.5
66
11.08
D
Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide).
1000 VDC
1500 VDC
2000 VDC
f
Hz
10 2 5 10 2 5 10 2 5 10
2 3 4 5
5
2
5
2
400
10
10
2
1
U
V
rms
1.0 µF
2.2 µF
3.3 µF
0.047 µF
0.022 µF
0.1 µF
4700 pF
2200 pF 1000 pF
0.22 µF
0.47 µF
0.01 µF
WIMA MKP 4
WIMA MKS 4
Permissible AC voltage
in relation to frequency
at 10) C internal temperature rise
(general guide).
Technical information and general data see page 57.
Continuation
16
11.08
D
Recommendation for Processing
and Application of
Through-Hole Capacitors
Soldering Process
A preheating of through-hole WIMA
capacitors is allowed for temperatures
Tmax 100 ° C.
In practice a preheating duration of
t 5 min. has been proven to be best.
Single wave soldering
Soldering bath temperature: T 260 ° C
Immersion time: t 5 sec
Double wave soldering
Soldering bath temperature: T 260 ° C
Immersion time: 2 x t 3 sec
Due to different soldering processes and
heat requirements the graphs are to be
regarded as a recommendation only.
2 s 3 s
30 60 90 120 150 180 210 240 sec][
t
T
260
240
220
200
180
160
140
120
100
80
60
40
20
[°C] 10 s
see detail-
enlargement
Wave soldering
Typical temperature/time graph for double wave soldering
WIMA Quality and Environmental Philosophy
ISO 9001:2000 Certification
ISO 9001:2000 is an international basic
standard of quality assurance systems for
all branches of industry. The approval
according to ISO 9001:2000 of our
factories by the VDE inspectorate certifies
that organisation, equipment and moni-
toring of quality assurance in our factories
correspond to internationally recognized
standards.
WIMA WPCS
The WIMA Process Control System (WPCS)
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA
production. Points of application of WPCS
during production process:
” incoming material inspection
” metallization
” film inspection
” schoopage
” pre-healing
” lead attachment
” cast resin preparation/
encapsulation
” 100% final inspection
” AQL check
WIMA Environmental Policy
All WIMA capacitors, irrespective of
whether through-hole devices or SMD,
are made of environmentally friendly
materials. Neither during manufacture
nor in the product itself any toxic
substances are used, e.g.
– Lead – PBB/PBDE
– PCB – Arsenic
– CFC – Cadmium
– Hydrocarbon chloride – Mercury
– Chromium 6+ – etc.
We merely use pure, recyclable materials
for packing our components, such as:
” carton
” cardboard
” adhesive tape made of paper
” polystyrene
We almost completely refrain from using
packing materials such as:
” foamed polystyrene (Styropor®)
” adhesive tapes made of plastic
” metal clips
RoHS Compliance
According to the RoHS Directive 2002/95/EC
certain hazardous substances like e.g. lead,
cadmium, mercury must not be used any
longer in electronic equipment as of July 1st,
2006. For the sake of the environment WIMA
has refraind from using such substances since
years already.
Tape for lead-free WIMA capacitors
DIN EN ISO 14001:2005
WIMA’s environmental management has
been established in accordance with the
guidelines of DIN EN ISO 14001:2005.
The certification has been granted in
June 2006.
121
11.08
D
P
P1
P0
P2
F
d
P
P1
H1
H
P0
d
P2
F
t
D0
W2
Vh
W0
P1
P2
P0
P
H1
H
W
1
W
d
F
Diagram 1:
PCM 2.5/5/7.5mm
Diagram 3: PCM 22.5 and 27.5*mm
*PCM 27.5 taping possible with two feed holes between components
Diagram 2: PCM 10/15 mm
Dimensions for Radial Taping
Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping
Carrier tape width W 18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
Hold-down tape width W
0
6.0 for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing
adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape
Hole position W
1
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
Hold-down tape position W
2
0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max.
Feed hole diameter D
0
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
Pitch of component P 12.7
p1.0
12.7
p1.0
12.7
p1.0
25.4
p1.0
25.4
p1.0
38.1
p1.5
3
*8.1
p1.5
or 50.8
p1.5
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
Feed hole pitch P
0
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
Feed hole centre P
1
5.1
p0.5
3.85
p0.7
2.6
p0.7
7.7
p0.7
5.2
p0.7
7.8
p0.7
5.3
p0.7
to lead
Hole centre to P
2
6.35
p1.3
6.35
p1.3
6.35
p1.3
12.7
p1.3
12.7
p1.3
19.05
p1.3
19.05
p1.3
component centre
Feed hole centre to bottom H
v
16.5
p0.3
16.5
p0.3
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
edge of the component 18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
Feed hole centre to top H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
edge of the component 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0
Lead spacing at F 2.5
p0.5
5.0
+0.8
7.5
p0.8
10.0
p0.8
15
p0.8
22.5
p0.8
27.5
p0.8
upper edge of carrier tape
–0.2
Lead diameter d 0.4
p0.05
0.5
p0.05
„
0.5
p0.05
or
0.6
–0.05
„
0.5
p0.05
or
0.6
–0.05
0.8
–0.05
0.8
–0.05
0.8
–0.05
Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max.
Total tape thickness t 0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
ROLL/AMMO AMMO
Package
v
(see also page 122)
Unit see details page 124.
v
Please give „H“ dimensions and desired packaging type when ordering. Dims in mm.
„ Diameter of leads see General Data. Please clarify customer-specific deviations with the manufacturer.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P0 = 12.7 or 15.0 is possible
REEL
P 360 max.
B
52 p2 depending on
P 30 p1 58 p2 comp. dimensions
52 p2 54 p2 depending
REEL
P 360 max. B 58 p2
or
REEL
P 500 max. B 60 p2 on PCM and
P 30 p1 66 p2 P 25 p1 68 p2 component dimensions
+0.06 +0,06 +0,08 +0,08 +0.08
Typical Dimensions for
Taping Configuration
