CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com Size 20 Fixed Signal Contacts Size 8 Removable Power, Shielded and High Voltage Contacts Military/Industrial Quality Connectors U.L. Recognized File #E49351 CSA Recognized File #LR54219 D.E.S.C. 85039 Telecommunication U.L. File #E140980 Combo-D Series connectors permit mixed contact combinations of power, shielded, high voltage and signal contacts within the same connector body. Twenty connector variants are offered in six standard shell sizes. Two performance levels of Combo-D Series connectors are offered. The CBD Series connectors are professional quality connectors recommended for use in sheltered, noncorrosive indoor and outdoor environments having normal ventilation, but without temperature or humidity controls. The CBM Series connectors are military quality connectors recommended for use in sheltered, mildly corrosive environments having a wide range of temperature, pressure and humidity changes. These connectors will meet the applicable performance and dimensional requirements of IEC 807-2, Performance Level One and Two, and D.E.S.C. 85039. Combo-D Series connectors utilize precision machined signal contacts. Connector variants are available with contact terminations for solder and straight and 90 printed board mount terminations featuring a choice of inch or metric printed board footprints. Power, shielded and high voltage contacts are removable, having solder and straight and 90 printed board mount terminations. Power and shielded contacts are available with crimp terminations. For low level shielding requirements, ferrite inductors may be attached to both signal and power contacts of connectors having contact terminations which are straight or 90 angled for printed board mounting applications. Additional details may be obtained from the factory Applications Engineering Department. The female power contacts feature the Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male and female contacts and reduced contact resistance during operation. A wide assortment of printed board mounting hardware, cable support hoods, and locking systems is available from stock. A blind mating system is available for applications requiring connector coupling in recessed areas or mobile power coupling systems. CBD SERIES CONTACT VARIANTS FACE VIEW OF MALE OR REAR VIEW OF FEMALE SHELL SIZE 1 1 SHELL SIZE 2 2 A1 3 A1 A3 A2 A3 A1 A1 1 5W1 3W3 3WK3* A2 2 3 4 4 1 3 A1 2 5 7 7W2 5 4 8 9 6 10 11W1 SHELL SIZE 3 1 3 2 5 4 A1 A3 A2 1 3 4 A3 A4 2 5 A2 5 9W4 5W5 3 4 10 9 1 2 8 7 A1 A1 6 1 8 13W3 3 2 4 5 6 7 A2 1 9 10 11 12 13 14 15 2 3 4 5 6 A1 11 12 13 14 15 17W2 7 8 9 10 16 17 18 19 20 21W1 SHELL SIZE 4 A1 A3 A2 A5 A4 A6 A8 A7 A1 A3 A2 A5 A4 A6 1 8W8 A1 A2 1 2 3 4 5 6 3 2 5 6 4 A1 A2 1 7 3 2 7 8 13W6 7 8 9 A3 A4 A1 A2 1 2 3 4 5 6 21WA4 5 6 A3 A5 A4 17W5 7 8 9 10 11 A3 A1 1 12 13 14 15 16 17 18 19 20 21 22 10 11 12 13 14 15 16 17 4 9 10 11 12 2 3 4 5 6 7 8 9 10 11 12 13 A2 14 15 16 17 18 19 20 21 22 23 24 25 25W3 27W2 SHELL SIZE 5 A1 A3 A2 A4 A5 A6 A7 A1 A2 A3 1 2 3 4 5 6 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 7 8 1 A4 3 2 4 5 6 7 8 9 10 11 12 A1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 36W4 43W2 24W7 A2 2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 13 15 A1 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47W1 SHELL SIZE 6 A1 A2 1 2 3 4 5 6 10 7 8 9 A3 17 18 1 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 26 27 28 29 30 31 32 33 34 35 36 37 38 39 46W4 40 41 42 A4 *3WK3: M variant contains 2 male contacts and 1 female contact F variant contains 2 female contacts and 1 male contact FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com COMBO-D SERIES TECHNICAL CHARACTERISTICS MATERIALS AND FINISHES: MECHANICAL CHARACTERISTICS: Insulator: Glass filled polyester per MIL-M-24519 UL 94V-0, blue color, and composite. Signal Contacts, Fixed: Signal Contacts: Male contacts-precision machined brass alloy. Female contacts-precision machined high tensile phosphor bronze. Size 20 contacts, male contact-0.040 inch [1.02mm] diameter. CBD Series has open entry design female contacts. CBM Series has closed entry design female contacts. Contact Retention in Insulator: Signal-9 lbs. [40N]. Power, shielded and high voltage-22 lbs [98N]. Signal Contact Plating: Gold flash over nickel plate and gold 0.000050 [1.27] over nickel plate. Other finishes available upon request. Power Contacts: Machined of high conductivity copper alloy for both male and female contacts. Power Contact Plating: Gold flash over nickel. Other finishes available upon request. Shielded and High Voltage Contacts: Male contacts-precision machined brass. Female contacts-precision machined high tensile phosphor bronze. Shielded and High Voltage Signal contact-gold flash over nickel. Contact Plating: Other finishes available upon request. Resistance to Solder Iron Heat: 500F [260C] for 10 seconds duration per IEC 512-6. Signal Contact Terminations: Solder contacts - 0.042 inch [1.06mm] minimum hole diameter for 20 AWG [0.5 mm2] wire maximum. Straight Printed Board Mount - 0.028 inch [0.71mm] diameter. 90 Printed Board Mount - 0.028 inch [0.71 mm] diameter. Power Contacts, Removable, Crimp or Solder Termination: Size 8 contact, male contact - 0.142 inch [3.61mm] diameter. Female contact features Large Surface Area (L.S.A.) closed entry contact design utilizing BeCu mechanical retention member. Male and female contacts have terminations for wire sizes 8, 12 and 16 AWG. Power Contacts, Printed Board Mount: Size 8 contact, male contact - 0.142 inch [3.61mm] diameter. Printed board terminations with 0.078 inch [1.98mm], 0.093 inch [2.36mm] and 0.125 inch [3.18mm] diameters. Shells: Steel or brass with tin plate; zinc plate with dichromate seal, stainless steel passivated. Other materials and finishes available upon request. Mounting Spacers and Brackets: Nylon plastic, or brass with tin plate; zinc plate with dichromate seal. Push-On Fasteners: Phosphor bronze and beryllium copper with tin plate. Jackscrew Systems: Steel with zinc plate and dichromate seal, or clear zinc plate. Shielded Contacts, Removable: See table of maximum cable sizes for contact termination dimensions. Hoods: Composite and plastic, UL 94V-0, brass or steel with zinc plate and dichromate seal. High Voltage Contacts: Straight and 90 terminations - 0.041 inch [1.04mm] minimum hole diameter. Shells: Male shells may be dimpled for EMI/ESD ground paths. Polarization: Trapezoidally shaped shells and polarized jackscrews. Mounting to Angle Brackets: Jackscrews and riveted fasteners with 0.120 inch [3.05mm] diameter hole, and threaded riveted fasteners with 4-40 threads and nylon inserts. Mounting to Printed Board: Rapid installation push-on fasteners and threaded posts. Locking Systems: Jackscrews. Mechanical Operations, Signal Contacts: CBD Series, 500 operations, CBM Series, 1,000 operations per IEC 512-5. ELECTRICAL CHARACTERISTICS: SIGNAL CONTACTS Contact Current Rating: 7.5 amperes nominal. Initial Contact Resistance: 0.008 ohms maximum. Proof Voltage: 1000 V r.m.s. POWER CONTACTS Contact Current Rating: 10, 15, 20, 30 and 40 amperes nominal. Initial Contact Resistance: 0.0005 ohms max. per IEC 512-2, Test 2b. Proof Voltage: 1000 V r.m.s. SHIELDED CONTACTS Initial Contact Resistance: 0.008 ohms maximum. Nominal Impedance: 50 ohms. Insertion Loss: -0.46 dB at 1 GHz -1.5 dB at 2 GHz VSWR: 1.15 average at 1 GHz 1.56 average at 2 GHz Above values measured using frequency domain techniques. Proof Voltage: 1000 V r.m.s. CLIMATIC CHARACTERISTICS: Temperature Range: -55C to +125C. Damp Heat, Steady State: 10 days. HIGH VOLTAGE CONTACTS Flash over Voltage: 3600 V r.m.s. Proof Voltage: 2700 V r.m.s. Initial Contact Resistance: 0.008 ohms maximum. CONNECTOR Insulator Resistance: Clearance and Creepage Distance: Working Voltage: 5 G ohms. 0.039 inch [1.0mm] minimum. 300 V r.m.s. DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 2 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com CBD3W3M00000 CBD5W5M00000 STANDARD SHELL ASSEMBLY M B B1 D1 E 0.0500.010 [1.270.25] D H 0.0360.008 [0.910.20] C A 10 Typ. G K O0.1200.005 [O3.050.13] Mounting hole, two places 0.220 [5.59] Max. OPTIONAL SHELL ASSEMBLY WITH UNIVERSAL FLOAT MOUNTS [F] OPTIONAL SHELL ASSEMBLY [0, 02] 0.1200.010 [3.050.25] O0.1200.005 [O3.050.13] Mounting hole, two places for stainless steel shell (0 option) O0.154 [3.91] Mounting hole, two places (02 option) SHELL SIZES SHELL SIZE 1 MALE SHELL SIZE 1 FEMALE SHELL SIZE 2 MALE SHELL SIZE 2 FEMALE SHELL SIZE 3 MALE SHELL SIZE 3 FEMALE SHELL SIZE 4 MALE SHELL SIZE 4 FEMALE SHELL SIZE 5 MALE SHELL SIZE 5 FEMALE SHELL SIZE 6 MALE SHELL SIZE 6 FEMALE 3 A 0.015 [0.38] 1.213 [30.81] 1.213 [30.81] 1.541 [39.14] 1.541 [39.14] 2.088 [53.04] 2.088 [53.04] 2.729 [69.32] 2.729 [69.32] 2.635 [66.93] 2.635 [66.93] 2.729 [69.32] 2.729 [69.32] B 0.005 [0.13] B1 0.005 [0.13] C 0.005 [0.13] 0.666 [16.92] 0.984 [24.99] 0.984 [24.99] 1.312 [33.32] 1.312 [33.32] 1.852 [47.04] 1.852 [47.04] 2.500 [63.50] 2.500 [63.50] 2.406 [61.11] 2.406 [61.11] 2.500 [63.50] 2.500 [63.50] 0.643 [16.33] 0.994 [25.25] 0.971 [24.66] 1.534 [38.96] 1.511 [38.38] 2.182 [55.42] 2.159 [54.84] 2.079 [52.81] 2.064 [52.43] 2.212 [56.18] 2.189 [55.60] DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. +0.13 O0.086+0.005 -0.000 O2.18-0.00 Mounting hole, two places [ 0.032 [0.81] Total diametral float D 0.005 [0.13] D1 0.005 [0.13] E 0.015 [0.38] G 0.010 [0.25] H 0.010 [0.25] K 0.005 [0.13] M 0.010 [0.25] 0.329 [8.36] 0.494 [12.55] 0.494 [12.55] 0.494 [12.55] 0.494 [12.55] 0.494 [12.55] 0.494 [12.55] 0.494 [12.55] 0.494 [12.55] 0.605 [15.37] 0.605 [15.37] 0.668 [16.97] 0.668 [16.97] 0.759 [19.28] 0.759 [19.28] 1.083 [27.51] 1.083 [27.51] 1.625 [41.28] 1.625 [41.28] 2.272 [57.71] 2.272 [57.71] 2.178 [55.32] 2.178 [55.32] 2.302 [58.47] 2.302 [58.47] 0.422 [10.72] 0.422 [10.72] 0.422 [10.72] 0.422 [10.72] 0.422 [10.72] 0.422 [10.72] 0.422 [10.72] 0.422 [10.72] 0.534 [13.56] 0.534 [13.56] 0.596 [15.14] 0.596 [15.14] 0.233 [5.92] 0.243 [6.17] 0.233 [5.92] 0.243 [6.17] 0.230 [5.84] 0.243 [6.17] 0.230 [5.84] 0.243 [6.17] 0.230 [5.84] 0.243 [6.17] 0.230 [5.84] 0.243 [6.17] 0.422 [10.72] 0.429 [10.90] 0.422 [10.72] 0.429 [10.90] 0.426 [10.82] 0.429 [10.90] 0.426 [10.82] 0.429 [10.90] 0.426 [10.82] 0.429 [10.90] 0.426 [10.82] 0.429 [10.90] 0.311 [7.90] 0.329 [8.36] 0.311 [7.90] 0.329 [8.36] 0.311 [7.90] 0.329 [8.36] 0.311 [7.90] 0.441 [11.20] 0.423 [10.74] 0.503 [12.78] 0.485 [12.32] ] FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com SOLDER CONNECTOR CODE 2 20 AWG max. [0.5 mm2] 0.125 [3.18] Fixed female jackscrews Fixed female jackscrew For solder contacts, specify code 2 in step 4 of ordering information. 0.345 [8.76] Fixed male jackscrew Fixed male and female polarized jackscrews available. Specify code T6 in step 7 of ordering information. Typical part number: CBD7W2M200T60 Typical part number: CBD7W2M200T0 STRAIGHT PRINTED BOARD MOUNT CONNECTOR CODE 3, 35, 36 AND 37 CODE NUMBER DO 3 --------- 35 0.078 [1.98] 36 0.093 [2.36] 37 0.125 [3.18] Fixed female jackscrews Swaged spacer with push-on fastener, phosphor bronze. 0.010 Min. [0.25] 0.170 [4.32] 0.250 [6.35] 0.028 O [0.71] Typical part number: CBD17W2F35S60T2X For straight printed board mount contacts, specify code no. in step 4 of ordering information. CBD17W2F200E0 with FS4008D contacts. CBD17W2M55B30T20 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 4 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com COMPLIANT PRESS-FIT CONNECTOR CODE 93 Fixed female jackscrews Swaged spacer with 4-40 threads 0.265 [6.73] 0.225 [5.72] max. thread length in mounting spacer 0.225 [5.72] 0.045 [1.14] Screw, 4-40 customer supplied TYPICAL PART NUMBER: CBD17W2M93S0T20 SUGGESTED PRINTED BOARD HOLE SIZES 0.0010 [25] MINIMUM COPPER PLATE THICKNESS DRILLED HOLE O0.0394+0.0035-0.0024 [1.000+0.090-0.060] FINISHED HOLE 0.0005 [13] MINIMUM SOLDER THICKNESS 0.0010 [25] MINIMUM COPPER PLATE THICKNESS DRILLED HOLE O0.119+0.002 [13.02+0.05] FINISHED HOLE 0.0005 [13] MINIMUM SOLDER THICKNESS Size 20 contacts Size 8 contacts Suggest 0.120 [3.05] O hole for mounting holes. TEMPERATURE RISE CURVE RATED CURRENT (AMPS) Note: For other PCB plating compositions, i.e. ENIG, (Electroless Nickel, Immersion Gold), consult Technical Sales. O TEMPERATURE RISE ( C) Curve developed using CBD8W8M00000 and CBD8W8F93S000 connectors and MC4008D contacts and 8 awg (10.0mm2) size wire. All contacts under load. 5 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com COMPLIANT TERMINATION PRESS-FIT CONNECTOR INSTALLATION TOOLS 1/2 inch shaft for Arbor Press. Replaceable Seating Pins Single Contact Insertion Tool Single Contact Removal Tool Arbor Press Female Connector Seating Tool (Male - not shown) Positronic recommended tools for CBD Series Connectors and Contacts CONTACT VARIANT CONNECTOR SEATING MALE FEMALE 5W1 9512-1-0-41 9512-18-0-41 3W3 9512-2-0-41 9512-19-0-41 3WK3 MALE FEMALE SINGLE CONTACT REMOVAL 9512-103-0-0 FOR SIZE 20 CONTACTS ONLY 9512-104-0-0 FOR SIZE 20 CONTACTS ONLY 9512-105-0-0 FOR SIZE 20 CONTACTS ONLY SIZE 8 CONTACTS ARE NOT REPAIRABLE SIZE 8 CONTACTS ARE NOT REPAIRABLE SIZE 8 CONTACTS ARE NOT REPAIRABLE SINGLE CONTACT INSERTION CONTACT TECHNICAL SALES 7W2 9512-2-0-41 9512-20-0-41 11W1 9512-2-0-41 9512-21-0-41 5W5 9512-3-0-41 9512-22-0-41 9W4 9512-3-0-41 9512-23-0-41 13W3 9512-3-0-41 9512-24-0-41 17W2 9512-3-0-41 9512-25-0-41 21W1 9512-3-0-41 9512-26-0-41 8W8 9512-4-0-41 9512-27-0-41 13W6 9512-4-0-41 9512-28-0-41 17W5 9512-4-0-41 9512-29-0-41 21WA4 9512-4-0-41 9512-30-0-41 25W3 9512-4-0-41 9512-31-0-41 27W2 9512-4-0-41 9512-32-0-41 24W7 9512-5-0-41 9512-33-0-41 36W4 9512-5-0-41 9512-34-0-41 43W2 9512-5-0-41 9512-35-0-41 47W1 9512-5-0-41 9512-36-0-41 46W4 9512-16-0-41 9512-37-0-41 Arbor press for connector seating tools-9530-1-0 1 ton capacity 4 inch throat Size 20 Female - 855-347-18-41 Replacement pins for connector seating tools. Size 8 Male - 855-347-19-41 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 6 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com STRAIGHT PRINTED BOARD MOUNTED POWER CONTACTS Straight printed board mount power contacts are mounted in connector when ordered. FEMALE CLOSED ENTRY, L.S.A. MALE 0.142 O [3.61] 0.626 [15.90] 0.170 [4.32] 0.634 [16.10] PART NUMBER AO CURRENT RATING PART NUMBER AO CURRENT RATING FDS4314D 0.078 [1.98] 15 Amps. MDS4314D 0.078 [1.98] 15 Amps. FDS4312D 0.094 [2.39] 20 Amps. MDS4312D 0.094 [2.39] 20 Amps. FDS4310D 0.125 [3.18] 30 Amps. MDS4310D 0.125 [3.18] 30 Amps. Material - High conductivity copper alloy. Plating - Gold flash over nickel. 0.000030 [0.75] gold over nickel available by adding -14 suffix on part number. 0.000050 [1.27] gold over nickel available by adding -15 suffix on part number. Note: Female power contacts feature Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male and female contacts and reduced contact resistance during operation. 90 PRINTED BOARD MOUNT POWER CONTACTS 90 printed board mount power contacts are mounted in connector when ordered. 0.142 O [3.61] FEMALE MALE CLOSED ENTRY, L.S.A. PART CURRENT NUMBER FRT4314D 15 Amps FRT4414D 15 Amps FRT4714D 15 Amps FRT4814D 15 Amps FRT4310D 30 Amps FRT4410D 30 Amps A REF. BO C 0.580 [14.73] 0.692 [17.58] 0.661 [16.79] 0.773 [19.63] 1.051 [26.70] 1.051 [26.70] 0.078 [1.98] 0.078 [1.98] 0.078 [1.98] 0.078 [1.98] 0.125 [3.18] 0.125 [3.18] 0.339 [8.61] 0.451 [11.46] 0.420 [10.67] 0.520 [13.21] 0.810 [20.57] 0.810 [20.57] PART CURRENT NUMBER SHELL SIZE BEND CODE 1, 2, 3 & 4 55 MRT4314D 15 Amps 5 55 MRT4414D 15 Amps 1, 2, 3 & 4 75 MRT4714D 15 Amps 5 75 MRT4814D 15 Amps 1, 2, 3 & 4 57 MRT4310D 30 Amps 5 57 MRT4410D 30 Amps Material - High conductivity copper alloy. Plating - Gold flash over nickel. 0.000030 [0.75] gold over nickel available by adding -14 suffix on part number. 0.000050 [1.27] gold over nickel available by adding -15 suffix on part number. 7 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. A REF. BO C 0.580 [14.73] 0.692 [17.58] 0.661 [16.79] 0.773 [19.63] 1.051 [26.70] 1.051 [26.70] 0.078 [1.98] 0.078 [1.98] 0.078 [1.98] 0.078 [1.98] 0.125 [3.18] 0.125 [3.18] 0.339 [8.61] 0.451 [11.46] 0.420 [10.67] 0.520 [13.21] 0.810 [20.57] 0.810 [20.57] Note: SHELL SIZE BEND CODE 1, 2, 3 & 4 55 5 55 1, 2, 3 & 4 75 5 75 1, 2, 3 & 4 57 5 57 Female power contacts feature Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male and female contacts and reduced contact resistance during operation. FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.125 [3.18] O POWER CONTACTS 0.220 [5.59] Max. CODE 5 AND 57, 0.283 [7.19] CONTACT EXTENSION (30 amps nominal) CBD***R7*** 0.283 [7.19] CONTACT EXTENSION Fixed female jackscrews 0.008 Specify code 5 or 57 in step 4 of ordering information. SHELL SIZE A B C D SHELL SIZE 1 1.204 [30.58] 0.984 [24.99] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 2 1.532 [38.91] 1.312 [33.32] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 3 2.072 [52.63] 1.852 [47.04] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 4 2.720 [69.09] 2.500 [63.50] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 5 2.626 [66.70] 2.406 [61.11] 0.395 [10.03] 0.283 [7.19] 0.112 [2.84] Typ. 0.112 [2.84] Typ. 0.810 [20.57] 0.112 [2.84] Typ. Numbering shown is rear view of male and face view of female. Push-on fastener, 0.170 [4.32] beryllium copper. Nominal Typical part number: CBD17W2M57R7NT20 0.810 [20.57] 0.125 [3.18] O Typical part number: CBD36W4F57R7NT2X 0.028 [0.71] O 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.078 [1.98] O POWER CONTACTS 0.220 [5.59] Max. CODE 5 AND 55, 0.283 [7.19] CONTACT EXTENSION (15 amps nominal) CBD***R7*** 0.283 [7.19] CONTACT EXTENSION Fixed female jackscrews 0.008 Specify code 5 or 55 in step 4 of ordering information. SHELL SIZE A B C D SHELL SIZE 1 1.204 [30.58] 0.984 [24.99] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 2 1.532 [38.91] 1.312 [33.32] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 3 2.072 [52.63] 1.852 [47.04] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 4 2.720 [69.09] 2.500 [63.50] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 5 2.626 [66.70] 2.406 [61.11] 0.395 [10.03] 0.283 [7.19] 0.339 [8.61] 0.112 [2.84] Typ. Typical part number: CBD17W2M55R7NT20 Numbering shown is rear view of male and face view of female. Push-on fastener, beryllium copper. 0.170 [4.32] Nominal 0.078 [1.98] O 0.028 [0.71] O 0.451 [11.46] 0.112 [2.84] Typ. 0.112 [2.84] Typ. Typical part number: CBD36W4F55R7NT2X DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 8 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com METRIC SYSTEM 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.078 [1.98] O POWER CONTACTS 0.125 [3.18] O Typ. 0.220 [5.59] Max. CODE 7 AND 75, 0.370 [9.40] CONTACT EXTENSION (15 amps nominal) CBD***R7*** 0.370 [9.40] CONTACT EXTENSION SHELL SIZE A B C D SHELL SIZE 1 1.204 [30.58] 0.984 [24.99] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 2 1.532 [38.91] 1.312 [33.32] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 3 2.072 [52.63] 1.852 [47.04] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 4 2.720 [69.09] 2.500 [63.50] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 5 2.626 [66.70] 2.406 [61.11] 0.470 [11.94] 0.370 [9.40] 0.008 Fixed female jackscrews 0.520 [13.21] 0.100 [2.54] Typ. 0.100 [2.54] Typ. Specify code 7 or 75 in step 4 of ordering information. 0.420 [10.67] Numbering shown is rear view of male and face view of female. 0.100 [2.54] Typ. 0.170 [4.32] Nominal Typical part number: CBD17W2M75R70T20 0.078 [1.98] O 0.024 [0.61] O Typical part number: CBD36W4M75R70T20 METRIC SYSTEM 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.125 [3.18] O POWER CONTACTS 0.125 [3.18] O Typ. 0.220 [5.59] Max. CODE 7 AND 77, 0.370 [9.40] CONTACT EXTENSION (30 amps nominal) CBD***R7*** 0.370 [9.40] CONTACT EXTENSION Fixed female jackscrews 0.008 SHELL SIZE A B C D SHELL SIZE 1 1.204 [30.58] 0.984 [24.99] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 2 1.532 [38.91] 1.312 [33.32] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 3 2.072 [52.63] 1.852 [47.04] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 4 2.720 [69.09] 2.500 [63.50] 0.420 [10.67] 0.370 [9.40] SHELL SIZE 5 2.626 [66.70] 2.406 [61.11] 0.470 [11.94] 0.370 [9.40] 0.810 [20.57] 0.100 [2.54] Typ. Specify code 7 or 77 in step 4 of ordering information. Numbering shown is rear view of male and face view of female. 0.810 [20.57] 0.100 [2.54] Typ. Typical part number: CBD17W2M77R70T20 9 0.100 [2.54] Typ. DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 0.125 [3.18] O 0.170 [4.32] Nominal 0.024 [0.61] O Typical part number: CBD36W4M77R70T20 FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com SHELL SIZE 6 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.078 [1.98] O POWER CONTACTS CODE 5 AND 55, 0.283 [7.19] CONTACT EXTENSION CONNECTOR VARIANT 46W4 (15 amps nominal) Fixed female jackscrews 0.451[11.46] Shell size 6 connector 2.720 [69.09] 0.507[12.88] 0.283[7.19]-Specify code 5 or 55 in step 4 of ordering information Numbering shown is rear view of male and face view of female 0.112[2.84] Typ. Typical part number: CBD46W4M55R7NT20 0.008 2.500 [63.50] 0.170[4.32] Nominal Push-on fastener, beryllium copper 0.078[1.98] O 0.028[0.71] O SHELL SIZE 6 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.125 [3.18] O POWER CONTACTS CODE 5 OR 57, 0.283 [7.19] CONTACT EXTENSION CONNECTOR VARIANT 46W4 (30 amps nominal) Fixed female jackscrews 0.451[11.46] Shell size 6 connector 2.720 [69.09] 0.810 [20.57] 0.283[7.19]-Specify code 5 or 57 in step 4 of ordering information 0.112[2.84] Typ. Typical part number: CBD46W4M57R7NT20 0.170[4.32] Nominal 0.008 2.500 [63.50] Numbering shown is rear view of male and face view of female Push-on fastener, beryllium copper 0.125[3.18] O 0.028[0.71] O DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 10 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com 90 AND STRAIGHT PRINTED BOARD CONTACT HOLE PATTERN WITH 0.078 [1.98] O, 0.094 [2.39] O AND 0.125 [3.18] O POWER CONTACTS Hole identification shown for male connector, use mirror image for female connector. Mount connector with mating face positioned to follow direction of arrow. 0.218 [5.54] TYP. 0.162 [4.11] TYP. 0.656 [16.66] TYP. 0.492 [12.50] TYP. 5W1 0.108 [2.74] TYP. 0.162 [4.11] TYP. 0.270 [6.86] TYP. 0.054 [1.37] TYP. 0.270 [6.86] TYP. 0.108 [2.74] TYP. 0.216 [5.49] TYP. 0.656 [16.66] TYP. 0.656 [16.66] TYP. 3W3/3WK3 11W1 7W2 0.108 [2.74] TYP. 0.216 [5.49] 0.162 [4.11] 0.268 [6.81] TYP. 0.034 [0.86] 0.570 [14.48] TYP. 0.926 [23.52] TYP. 0.108 [2.74] TYP. 0.054 [1.37] TYP. 0.306 [7.77] 0.570 [14.48] TYP. 0.926 [23.52] TYP. 0.306 [7.77] 0.570 [14.48] TYP. 0.926 [23.52] TYP. 5W5 9W4 13W3 0.650 [16.51] 0.250 [6.35] TYP. 0.150 [3.81] 0.109 [2.77] TYP. 0.218 [5.54] TYP. 0.109 [2.77] TYP. 0.600 [15.24] 0.900 [22.86] TYP. 1.250 [31.75] TYP. 0.163 [4.14] TYP. 0.926 [23.52] TYP. 0.054 [1.37] TYP. 0.544 [13.82] TYP. 0.926 [23.52] TYP. 21W1 17W2 8W8 0.707 [17.96] 0.275 [6.99] TYP. 0.109 [2.77] TYP. 0.652 [16.56] 0.092 [2.34] 0.265 [6.73] TYP. 1.250 [31.75] TYP. 0.893 [22.68] TYP. 0.055 [1.40] TYP. 1.250 [31.75] TYP. 0.112 [2.84] 0.100 [2.54] Y 0.056 [1.42] 0.056 [1.42] 0.050 [1.27] A 0.100 [2.54] 0.112 [2.84] 0.100 [2.54] 0.900 [22.86] TYP. 0.650 [16.51] TYP. 11 0.050 [1.27] 43W2 0.056 [1.42] 0.050 [1.27] DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 0.810 [20.57] 0.109 [2.77] TYP. 43 PLACES B A 0.060 [1.52] TYP. TYP. 0.120 [3.05] TYP. 38 PLACES 1.250 [31.75] TYP. 46W4 B 0.055 [1.40] TYP. 1.203 [30.56] TYP. 0.270 [6.86] 0.540 [13.72] 1.203 [30.56] TYP. 36W4 0.112 [2.84] 24W7 0.810 [20.57] 0.540 [13.72] 0.109 [2.77] TYP. 0.810 [20.57] TYP. 0.055 [1.40] TYP. 0.109 [2.77] TYP. 7 & 75 0.109 [2.77] TYP. 1.203 [30.56] TYP. 27W2 25W3 X 0.270 [6.86] TYP. 0.109 [2.77] TYP. 0.055 [1.40] TYP. 0.618 [15.70] 1.250 [31.75] TYP. 5 & 55 21WA4 17W5 0.893 [22.68] TYP. 0.109 [2.77] TYP. 3, 35 & 37 0.055 [1.40] TYP. 1.250 [31.75] TYP. 0.055 [1.40] TYP. 0.618 [15.70] 1.250 [31.75] TYP. 13W6 CODE NO. 0.893 [22.68] TYP. 0.618 [15.70] TYP. 0.109 [2.77] TYP. 0.343 [8.71] 0.109 [2.77] TYP. Suggest Suggest Suggest Suggest Suggest 0.045 0.098 0.114 0.145 0.123 0.055 [1.40] TYP. 1.203 [30.56] TYP. 47W1 [1.14] O hole for signal contact termination positions. [2.49] O hole for 0.078 [1.98] O power contact termination positions. [2.90] O hole for 0.094 [2.39] O power contact termination positions. [3.68] O hole for 0.125 [3.18] O power contact termination positions. 0.003 [3.12] O hole for mounting connector with push-on fasteners. FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com 90 PRINTED BOARD CONTACT HOLE PATTERN WITH 0.125 [3.18] O POWER CONTACTS Hole identification shown for male connector, use mirror image for female connector. Mount connector with mating face positioned to follow direction of arrow. 0.218 [5.54] TYP. 0.108 [2.74] TYP 6 PLACES. 0.162 [4.11] TYP. 0.270 [6.86] TYP. 0.270 [6.86] TYP. 0.162 [4.11] TYP. 0.054 [1.37] TYP. 0.108 [2.74] TYP. 3 PLACES 0.656 [16.66] TYP. 0.656 [16.66] TYP. 0.492 [12.50] TYP. 3W3/3WK3 5W1 0.108 [2.74] TYP. 3 PLACES 0.216 [5.49] 0.162 [4.11] 0.268 [6.81] TYP. 2 PLACES 0.034 [0.86] 0.570 [14.48] TYP. 5W5 11W1 0.108 [2.74] TYP. 8 PLACES 0.054 [1.37] TYP. 9W4 0.306 [7.77] 0.570 [14.48] TYP. 0.926 [23.52] TYP. 0.250 [6.35] TYP. 3 PLACES 0.150 [3.81] 0.054 [1.37] TYP. 0.163 [4.14] TYP. 0.544 [13.82] TYP. 0.926 [23.52] TYP. 0.926 [23.52] TYP. 0.600 [15.24] 0.900 [22.86] TYP. 1.250 [31.75] TYP. 21W1 8W8 0.707 [17.96] 0.275 [6.99] TYP. 3 PLACES 0.109 [2.77] TYP. 5 PLACES 0.652 [16.56] 0.343 [8.71] 0.055 [1.40] TYP. 0.618 [15.70] 1.250 [31.75] TYP. 0.055 [1.40] TYP. 1.250 [31.75] TYP. B 0.415 [10.54] 0.340 [8.64] C 0.359 [9.12] 0.290 [7.37] 24W7 0.810 [20.57] TYP. 0.055 [1.40] TYP. 0.810 [20.57] 0.540 [13.72] 0.109 [2.77] TYP. 29 PLACES 0.109 [2.77] TYP. 37 PLACES 0.270 [6.86] 0.540 [13.72] 1.203 [30.56] TYP. 0.055 [1.40] TYP. 1.203 [30.56] TYP. 43W2 36W4 X 0.112 [2.84] 0.100 [2.54] Y 0.056 [1.42] 0.050 [1.27] 0.109 [2.77] TYP. 16 PLACES 1.203 [30.56] TYP. 27W2 25W3 0.390 [9.91] 0.270 [6.86] TYP. 6 PLACES 0.109 [2.77] TYP. 23 PLACES 0.055 [1.40] TYP. 0.618 [15.70] 1.250 [31.75] TYP. 0.471 [11.96] 21WA4 0.893 [22.68] TYP. 0.893 [22.68] TYP. 0.109 [2.77] TYP. 20 PLACES A 0.055 [1.40] TYP. 1.250 [31.75] TYP. 17W5 13W6 7 & 77 0.893 [22.68] TYP. 0.618 [15.70] TYP. 0.109 [2.77] TYP. 15 PLACES 0.109 [2.77] TYP. 10 PLACES 0.092 [2.34] 0.265 [6.73] TYP. 5 PLACES 1.250 [31.75] TYP. 5 & 57 13W3 0.650 [16.51] 0.109 [2.77] TYP. 16 PLACES 0.218 [5.54] TYP. 17W2 CODE NO. 0.656 [16.66] TYP. 7W2 0.306 [7.77] 0.570 [14.48] TYP. 0.926 [23.52] TYP. 0.926 [23.52] TYP. 0.109 [2.77] TYP. 13 PLACES 0.216 [5.49] TYP. 0.900 [22.86] TYP. 0.650 [16.51] TYP. 0.810 [20.57] 0.109 [2.77] TYP. 43 PLACES 0.060 [1.52] TYP. Suggest 0.045 [1.14] O hole for signal contact termination positions. 46W4 Suggest 0.145 [3.68] O hole for power contact termination positions. Suggest 0.1230.003 [3.12] O hole for mounting connector with push-on fasteners. 0.055 [1.40] TYP. X TYP. 0.120 [3.05] TYP. 38 PLACES 1.250 [31.75] TYP. 1.203 [30.56] TYP. 47W1 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 12 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com STRAIGHT PRINTED BOARD MOUNTED SHIELDED CONTACTS Straight printed board mount shielded contacts are mounted in connector when ordered. 0.040 O [1.02] 0.156 [3.96] 0.156 [3.96] 0.200 [5.08] 0.200 [5.08] 0.037 [0.94] Across points Suggest 0.045 [1.14] O hole 0.200 [5.08] 0.152 [3.86] O MALE FEMALE PART NO. A B C PART NO. A B C FDS4201D 0.481 [12.22] 0.025 [0.64] 0.181 [4.60] MDS4201D 0.489 [12.42] 0.025 [0.64] 0.181 [4.60] 0.100 [2.54] Material - Copper alloy with PTFE teflon insulator. Plating: Signal contact - 0.000030 [0.75] gold over nickel Contact body -Gold flash over nickel. FDS4201D and MDS4201D Contact hole pattern Signal contact - 0.000050 [1.27] gold over nickel Contact body - 0.000030 [0.75] gold over nickel available by adding -15 suffix on part number. *Technical characteristics are listed on page 21. 90 PRINTED BOARD MOUNT SHIELDED CONTACTS 90 printed board mount shielded contacts are mounted in connector when ordered. 0.162 [4.11] 0.162 [4.11] 0.152 O [3.86] 0.040 O [1.02] Suggest 0.045 [1.14] O hole 0.037 [0.94] Across points 0.200 [5.08] MALE FEMALE PART NO. A B C D PART NO. A B C D FRT4201D 0.827 [21.01] 0.240 [6.10] 0.259 [6.58] 0.470 [11.94] MRT4201D 0.829 [21.06] 0.240 [6.10] 0.253 [6.43] 0.470 [11.94] 0.100 [2.54] FRT4201D and MRT4201D Contact hole pattern Material - Copper alloy with PTFE teflon insulator. Plating: Signal contact - 0.000030 [0.75] gold over nickel Contact body -Gold flash over nickel. Signal contact - 0.000050 [1.27] gold over nickel Contact body - 0.000030 [0.75] gold over nickel available by adding -15 suffix on part number. 13 DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. *Technical characteristics are listed on page 21. FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com STRAIGHT PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED CONTACTS CODE 65, CONNECTOR WITH FDS4201D OR MDS4201D CONTACTS Fixed female jackscrews 0.250 [6.35] 0.028 [0.71] O 0.170 [4.32] Push-on fastener, phosphor bronze 0.156 [3.96] Numbering shown is rear view of male and face view of female. 0.025 [0.64] 0.028 [0.71] O 0.037 [0.94] Across points Typical part number: CBD17W2M65S60T20 90 PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED CONTACTS CODE 85, CONNECTOR WITH FRT4201D OR MRT4201D CONTACTS CBD**85**** 0.283 [7.19] CONTACT EXTENSION Fixed female jackscrews 0.008 SHELL SIZE A B C D SHELL SIZE 1 1.204 [30.58] 0.984 [24.99] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 2 1.532 [38.91] 1.312 [33.32] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 3 2.072 [52.63] 1.852 [47.04] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 4 2.720 [69.09] 2.500 [63.50] 0.339 [8.61] 0.283 [7.19] SHELL SIZE 5 2.626 [66.70] 2.406 [61.11] 0.395 [10.03] 0.545 [13.84] Numbering shown is rear view of male and face view of female. 0.156 [3.96] 0.170 [4.32] Nominal D - specify code 85 in step 4 of ordering information 0.112 [2.84] Typ. 0.028 O [0.71] 0.470 [11.94] Typical part number: CBD17W2M85R7NT20 Push-on fastener, beryllium copper 0.028 [0.71] O 1 place, 0.037 [0.94] Across points 2 places 0.470 [11.94] 0.112 [2.84] Typ. D - specify code 85 in step 4 of ordering information Typical part number: CBD36W4M85R7NT20 Note: Shell size 5 connectors are supplied inverted when ordered with 90 printed board mount shielded contacts. DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 14 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com STRAIGHT PRINTED BOARD MOUNT CONTACT HOLE PATTERN WITH FDS4201D AND MDS4201D SHIELDED CONTACTS Hole identification shown is for male connector, use mirror image for female connector. 0.218 [5.54] Typ. 0.162 [4.11] Typ. 0.108 [2.74] Typ. 0.270 [6.86] Typ. 0.112 [2.84] 0.200 [5.08] 0.100 [2.54] 0.056 [1.42] 0.492 [12.50] Typ. 0.100 [2.54] 0.054 [1.37] Typ. 0.200 [5.08] 0.200 [5.08] 0.200 [5.08] 0.056 [1.42] 0.100 0.270 [6.86] Typ. [2.54] 0.656 [16.66] Typ. 0.100 [2.54] 0.656 [16.66] Typ. 3W3/3WK3 5W1 0.034 [0.86] 0.056 [1.42] 0.216 [5.49] Typ. 0.656 [16.66] Typ. 7W2 0.216 [5.49] 0.162 [4.11] 0.200 [5.08] 0.268 [6.81] Typ. 0.108 [2.74] Typ. 0.162 0.112 [2.84] [4.11] Typ. 0.112 [2.84] 11W1 0.109 [2.77] Typ. 0.054 [1.37] Typ. 0.108 [2.74] Typ. 0.108 [2.74] Typ. 0.112 [2.84] 0.054 [1.37] Typ. 0.200 [5.08] 0.112 [2.84] 0.200 [5.08] 0.056 [1.42] 0.306 [7.77] 0.570 [14.48] Typ. 0.926 [23.52] Typ. 0.570 Typ. 0.100 [14.48] [2.54] 0.926 [23.52] Typ. 0.100 [2.54] 5W5 9W4 0.272 [6.91] Typ. 0.109 [2.77] Typ. 0.218 [5.54] Typ. 0.200 [5.08] 0.112 [2.84] 0.056 [1.42] 0.544 [13.82] Typ. 0.926 [23.52] Typ. 0.100 [2.54] 0.306 [7.77] 0.570 [14.48] Typ. 0.926 [23.52] Typ. 17W2 13W3 0.650 [16.51] 0.150 [3.81] 0.250 [6.35] Typ. 0.200 [5.08] 0.707 [17.96] 0.652 [16.56] 0.109 [2.77] Typ. 0.112 [2.84] 0.200 [5.08] 0.056 [1.42] 0.100 0.163 [4.14] [2.54] 0.926 [23.52] Typ. 0.100 [2.54] 1.250 [31.75] Typ. 21W1 0.275 [6.99] Typ. 0.109 [2.77] Typ. 0.112 [2.84] 0.109 [2.77] Typ. 0.055 [1.40] Typ. 17W5 Typ. 0.100 0.618 [15.70] [2.54] 0.893 [22.68] Typ. 1.250 [31.75] Typ. 21WA4 0.109 [2.77] Typ. 0.055 [1.40] Typ. 0.112 [2.84] 0.810 [20.57] 24W7 0.200 [5.08] 0.540 [13.72] 0.100 [2.54] 0.056 0.055 [1.42] [1.40] Typ. 0.109 [2.77] Typ. 1.203 [30.56] Typ. 0.810 [20.57] 0.112 [2.84] 0.224 [5.69] 0.109 0.056 [2.77] Typ. [1.42] 1.203 [30.56] Typ. 47W1 Suggest 0.045 [1.14] O hole for signal contact termination position. Suggest 0.1230.003 [3.12] O hole for mounting connector with push-on fasteners. DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 25W3 0.112 [2.84] 0.618 [15.70] 0.056 [1.42] 0.893 [22.68] Typ. 1.205 [31.75] Typ. 0.810 [20.57] Typ. 0.109 [2.77] Typ. 0.055 [1.40] Typ. 0.224 [5.69] 0.112 0.270 [6.86] [2.84] 0.540 [13.72] 1.203 [30.56] Typ. 36W4 0.200 [5.08] 0.100 [2.54] 0.055 [1.40] Typ. 43W2 15 0.109 [2.77] Typ. 0.055 [1.40] Typ. 0.056 [1.42] 0.109 [2.77] Typ. 1.203 [30.56] Typ. 27W2 0.112 [2.84] 0.200 [5.08] 0.100 [2.54] 0.270 [6.86] Typ. 0.112 [2.84] 0.056 [1.42] 0.893 [22.68] Typ. 1.250 [31.75] Typ. 0.100 [2.54] 0.224 [5.69] 0.200 [5.08] 0.056 [1.42] 0.055 [1.40] Typ. 0.618 [15.70] 1.250 [31.75] Typ. 0.100 [2.54] 0.200 [5.08] 13W6 8W8 0.343 [8.71] 0.200 [5.08] 0.056 [1.42] 0.092 [2.34] 0.265 [6.73] Typ. 1.250 [31.75] Typ. 0.100 [2.54] 0.600 [15.24] 0.900 [22.86] Typ. 0.120 [3.05] Typ. 0.060 [1.52] Typ. 0.100 [2.54] Typ. 0.650 [16.51] Typ. 0.050 [1.27] 0.900 [22.86] Typ. 1.250 [31.75] Typ. 46W4 FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D Positronic Industries, Inc. www.connectpositronic.com 90 PRINTED BOARD MOUNT CONTACT HOLE PATTERN WITH FRT4201D AND MRT4201D SHIELDED CONTACTS Hole identification shown is for male connector, use mirror image for female connector. Mount connector with mating face positioned to follow direction of arrow. 0.218 [5.54] Typ. 0.200 [5.08] 0.054 [1.37] Typ. 0.200 [5.08] 0.162 [4.11] Typ. 0.270 [6.86] Typ. 0.112 [2.84] 0.108 [2.74] Typ. 0.108 [2.74] Typ. 0.112 [2.84] 0.200 [5.08] 0.162 [4.11] Typ. 0.112 [2.84] 0.200 [5.08] 0.100 0.056 [1.42] [2.54] 0.492 [12.50] Typ. 0.131 [3.33] 0.100 [2.54] 0.131 [3.33] 0.056 [1.42] 0.270 [6.86] Typ. 0.656 [16.66] Typ. 0.100 [2.54] 0.656 [16.66] Typ. 0.131 [3.33] 3W3/3WK3 5W1 0.268 [6.81] Typ. 0.034 [0.86] 0.108 [2.74] Typ. 0.108 [2.74] Typ. 0.112 [2.84] 0.054 [1.37] Typ. 0.216 [5.49] 0.162 [4.11] 0.100 [2.54] 0.926 [23.52] Typ. 0.926 [23.52] Typ. 5W5 9W4 0.100 [2.54] 0.109 [2.77] Typ. 0.100 [2.54] 0.056 [1.42] 0.163 [4.14] Typ. 0.131 [3.33] 0.056 [1.42] 0.544 [13.82] Typ. 0.926 [23.52] Typ. 17W2 0.109 [2.77] Typ. 0.112 [2.84] 0.200 [5.08] 0.131 [3.33] 0.600 [15.24] 0.900 [22.86] Typ. 0.926 [23.52] Typ. 0.056 [1.42] 0.092 [2.34] 0.265 [6.73] Typ. 1.250 [31.75] Typ. 0.100 [2.54] 0.131 [3.33] 1.250 [31.75] Typ. 21W1 8W8 0.343 [8.71] 13W6 0.100 [2.54] 0.200 [5.08] 0.109 [2.77] Typ. 0.275 [6.99] Typ. 0.109 [2.77] Typ. 0.109 [2.77] Typ. 0.112 [2.84] 0.054 [1.37] Typ. 0.707 [17.96] 0.652 [16.56] 0.250 [6.35] Typ. 0.112 [2.84] 0.200 [5.08] 11W1 13W3 0.650 [16.51] 0.150 [3.81] 0.200 [5.08] 0.218 [5.54] Typ. 0.200 [5.08] 0.131 [3.33] 0.100 [2.54] 0.306 [7.77] 0.570 [14.48] Typ. 0.926 [23.52] Typ. 0.056 [1.42] 0.306 [7.77] 0.570 [14.48] Typ. 0.570 [14.48] Typ. 0.056 [1.42] 0.216 [5.49] Typ. 0.656 [16.66] Typ. 0.131 [3.33] 7W2 0.200 [5.08] 0.131 [3.33] 0.100 [2.54] 0.055 [1.40] Typ. 0.112 [2.84] 0.109 [2.77] Typ. 0.055 [1.40] Typ. 0.112 [2.84] 0.200 [5.08] 0.131 [3.33] 0.056 [1.42] 0.055 [1.40] Typ. 0.100 [2.54] 0.131 [3.33] 0.618 [15.70] 1.250 [31.75] Typ. 17W5 0.112 [2.84] 0.200 [5.08] 0.893 [22.68] Typ. 0.131 [3.33] 0.056 [1.42] 0.618 [15.70] 0.893 [22.68] Typ. 1.250 [31.75] Typ. 1.250 [31.75] Typ. 21WA4 0.109 [2.77] Typ. 0.055 [1.40] Typ. 0.100 [2.54] 0.618 [15.70] Typ. 0.893 [22.68] Typ. 0.374 [9.50] 25W3 0.200 [5.08] 0.109 [2.77] Typ. 0.056 [1.42] 0.109 [2.77] Typ. 0.100 [2.54] 0.075 0.270 [1.91] [6.86] Typ. 1.203 [30.56] Typ. 1.250 [31.75] Typ. 27W2 0.270 [6.86] 0.540 [13.72] 0.810 [20.57] Typ. 1.203 [30.56] Typ. 24W7 0.109 [2.77] Typ. 0.100 [2.54] 0.200 [5.08] 0.075 [1.91] 0.112 [2.84] 0.112 [2.84] 0.055 [1.40] Typ. 0.540 [13.72] 0.810 [20.57] 1.203 [30.56] Typ. 36W4 0.100 [2.54] 0.150 [3.81] 0.109 [2.77] Typ. 0.055 [1.40] Typ. 0.112 [2.84] 0.112 [2.84] 0.810 [20.57] 0.200 [5.08] 0.075 [1.91] 0.374 [9.50] 0.055 [1.40] Typ. 0.150 [3.81] 1.203 [30.56] Typ. 47W1 43W2 Suggest 0.045 [1.14] O hole for signal contact termination positions. Suggest 0.1230.003 [3.12] O hole for mounting connector with push-on fasteners. Note: Shell size 5 connectors are supplied inverted when ordered with 90 printed board mount shielded contacts. DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. 16 CBD/CBM SERIES INDUSTRIAL AND MILITARY QUALITY SUBMINIATURE-D CONNECTORS Combo-D Sub-D FOR MILITARY AND SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS Positronic Industries, Inc. www.connectpositronic.com ORDERING INFORMATION - CODE NUMBERING SYSTEM Specify Complete Connector By Following Steps 1 Through 9 Insert "0" When Step Is Not Used STEP 1 2 CBD 17W2 3 4 5 6 7 8 F 55 R7 N T2 X 9 STEP 1 - Basic Series **STEP 9 - Special Options CBD - Industrial Quality with Open Entry Signal Contacts CBM - Military Conformance with "Closed Entry" Signal Contacts plated 0.000050 [1.27] gold over nickel plate 759.0 - Blind Mate Pilot 759.1 - Blind Mate Panel -14 - Signal contacts plated 0.000030 [0.75] gold over nickel. STEP 8 - Shell Options STEP 2 - Combo-D Series Connector Variants 0 S X Z Shell Size 1 5W1 Shell Size 2 3W3, 3WK3, 7W2, 11W1 Shell Size 3 5W5, 9W4, 13W3, 17W2, 21W1 Shell Size 4 8W8, 13W6, 17W5, 21WA4, 25W3, 27W2 Shell Size 5 24W7, 36W4, 43W2, 47W1 Shell Size 6 46W4 0 V3 V5 VL T T2 T6 E E2 E6 M - Male F - Female DIMENSIONS ARE IN INCHES [MILLIMETERS]. ALL DIMENSIONS ARE SUBJECT TO CHANGE. - - - - - - - - - - None. Lock Tab, connector front panel mounted. Lock Tab, connector rear panel mounted. Lock Lever, used with Hoods only. Fixed Female Jackscrews. Fixed Female Jackscrews. Fixed Male and Female Polarized Jackscrews. Rotating Male Jackscrews. Rotating Male Screw Locks. Rotating Male and Female Polarized Jackscrews. *STEP 6 - Hoods and Push-On Fasteners 0 - None Z - Hood, Top or Side Opening, robust extended height, plastic and composite, with rotating male jackscrews, shell sizes 1 through 5 H - Hood, Top Opening, Metal, shell sizes 2 through 5 **G - Hood, EMI/RFI, Metal, shell sizes 1 through 6 N - Push-on Fastener, for 90 Mounting Brackets STEP 4 - Type of Contacts 17 Zinc Plated with Dichromate Seal Stainless Steel Tin Plated Tin Plated and Dimpled-male connector only *STEP 7 - Locking and Polarizing Systems STEP 3 - Connector Gender 0 - Connector ordered without size 8 power shielded or high voltage removable contacts. See pages 19, 20, 22 and 24 for contact part numbers. Available on 3W3, 3W3K, 5W5 and 8W8. 2 - Solder, Signal Contacts only. 3 - Solder, Straight Printed Board Mount with Signal Contacts, 0.170 [4.32] Tail Length. 35 - Solder, Straight Printed Board Mount with Signal and 0.078 [1.98] O Power Contacts, 0.170 [4.32] Tail Length. 36 - Solder, Straight Printed Board Mount with Signal and 0.094 [2.39] O Power Contacts, 0.170 [4.32] Tail Length. 37 - Solder, Straight Printed Board Mount with Signal and 0.125 [3.18] O Power Contacts, 0.170 [4.32] Tail Length. 5 - Solder, 90 Printed Board Mount with Signal Contacts only, 0.283 [7.19] Signal Contact Extension. 55 - Solder, 90 Printed Board Mount with Signal and 0.078 [1.98] O Power Contacts, 0.283 [7.19] Signal Contact Extension. 57 - Solder, 90 Printed Board Mount with Signal and 0.125 [3.18] O Power Contacts, 0.283 [7.19] Signal Contact Extension. 65 - Solder, Straight Printed Board Mount with Signal and Shielded Contacts MDS/FDS 4201D footprint, 0.170 [4.32] Signal Contact Tail Length. 7 - Solder, Metric System 90 Printed Board Mount with Signal Contacts only, 0.370 [9.40] Signal Contact Extension. 75 - Solder, Metric System 90 Printed Board Mount with Signal and 0.078 [1.98] O Power Contacts, 0.370 [9.40] Signal Contact Extension. 77 - Solder, Metric System 90 Printed Board Mount with Signal and 0.125 [3.18] O Power Contacts, 0.370 [9.40] Signal Contact Extension. *** 85 - Solder, 90 Printed Board Mount with Signal and Shielded Contacts MRT/FRT 4201D footprint, 0.283 [7.19] Signal Contact Extension. 93 - Size 20 Omega type compliant and Size 8 Bi-Spring type compliant, termination length 0.225 [5.72] - - - - *STEP 5 - Mounting Style 0 02 B3 B8 F P P2 R2 - - - - - - - - R6 - R7 - R8 - S - S2 - S5 - S6 - Mounting Hole, 0.120 [3.05] O Mounting Hole, 0.154 [3.91] O Bracket, Mounting, 90 Metal with Cross Bar Bracket, Mounting, 90 Plastic with Cross Bar Float Mounts, Universal Threaded Post, Brass, 0.250 [6.35] Length Threaded Post, Nylon, 0.250 [6.35] Length Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Thread Fixed Female Jackscrews with Cross Bar Bracket, Mounting, 90 Metal, Swaged to Connector with 0.120 [3.05] O Mounting Hole with Cross Bar Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Threads with Cross Bar Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Locknut with Cross Bar Swaged Spacer, 4-40 Threads, 0.250 [6.35] Length, Spacer length changes to .0265 [6.73] when used in conjunction with Code 93 contacts Swaged Spacer, 4-40 Threads, 0.125 [3.18] Length Swaged Locknut, 4-40 Threads Swaged Spacer with Push-on Fastener, 4-40 Threads, 0.250 [6.35] Length *For additional information on accessories listed in steps 5, 6, 7 & 9, see Accessory Catalog. **When using G hood with CBD variants, use the extended height hood. See Accessories Catalog for extended G hood options. ***Not available on shell size 6, CBD 46W4.