TLP3417
1
Photocouplers Photorelay
TLP3417
TLP3417
TLP3417
TLP3417
Start of commercial production
2014-07
1.
1.
1.
1. Applications
Applications
Applications
Applications
• ATE (Automatic Test Equipment)
• Measuring Instruments
• High-Speed Logic IC Testers
• High-Speed Memory Testers
2.
2.
2.
2. General
General
General
General
The TLP3417 is a photorelay in a VSON4 that consists of a photo MOSFET optically coupled with an infrared
light emitting diode. The TLP3417 is suitable for applications that require low output capacitance and high
withstand voltage, such as LCD testers.
3.
3.
3.
3. Features
Features
Features
Features
(1) Normally opened (1-Form-A)
(2) OFF-state output terminal voltage: 80 V (min)
(3) Trigger LED current: 3 mA (max)
(4) ON-state current: 120 mA (max)
(5) ON-state resistance: 7 Ω (typ.), 12 Ω (max)
(6) OFF-state Capacitance: 5 pF (typ.), 7 pF (max)
(7) Isolation voltage: 500 Vrms (min)
4.
4.
4.
4. Packaging and Pin Assignment
Packaging and Pin Assignment
Packaging and Pin Assignment
Packaging and Pin Assignment
11-2D1A
1: Anode
2: Cathode
3: Drain
4: Drain
5.
5.
5.
5. Internal Circuit
Internal Circuit
Internal Circuit
Internal Circuit
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
2
6.
6.
6.
6. Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
LED
Detector
Common
Characteristics
Input forward current
Input forward current derating
Input reverse voltage
Input power dissipation
Input power dissipation derating
Junction temperature
OFF-state output terminal voltage
ON-state current
ON-state current derating
ON-state current (pulsed)
Output power dissipation
Output power dissipation derating
Junction temperature
Storage temperature
Operating temperature
Lead soldering temperature
Isolation voltage
(Ta ≥ 25 )
(Ta ≥ 25 )
(Ta ≥ 25 )
(t = 100 ms, Duty = 1/10)
(Ta ≥ 25 )
(10 s)
AC, 60 s, R.H. ≤ 60 %
Symbol
IF
∆IF/∆Ta
VR
PD
∆PD/∆Ta
Tj
VOFF
ION
∆ION/∆Ta
IONP
PO
∆PO/∆Ta
Tj
Tstg
Topr
Tsol
BVS
Note
(Note 1)
Rating
30
-0.3
5
50
-0.5
125
80
120
-1.2
360
240
-2.4
125
-40 to 125
-40 to 110
260
500
Unit
mA
mA/
V
mW
mW/
V
mA
mA/
mA
mW
mW/
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: This device is considered as a two-terminal device: Pins 1 and 2 are shorted together, and pins 3 and 4 are
shorted together.
Note: This device is sensitive to electrostatic discharge (ESD). Extreme ESD conditions should be guarded against
by using proper antistatic precautions for the worktable, operator, solder iron, soldering equipment and so on.
7.
7.
7.
7. Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Characteristics
Supply voltage
Input forward current
ON-state current
Operating temperature
Symbol
VDD
IF
ION
Topr
Note Min
5
-20
Typ.
7.5
Max
64
20
120
85
Unit
V
mA
mA
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this data sheet should also be considered.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
3
8.
8.
8.
8. Electrical Characteristics (Unless otherwise specified, T
Electrical Characteristics (Unless otherwise specified, T
Electrical Characteristics (Unless otherwise specified, T
Electrical Characteristics (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
LED
Detector
Characteristics
Input forward voltage
Input reverse current
Input capacitance
OFF-state current
Output capacitance
Symbol
VF
IR
Ct
IOFF
COFF
Note Test Condition
IF = 10 mA
VR = 5 V
V = 0 V, f = 1 MHz
VOFF = 80 V
V = 0 V, f = 100 MHz, t < 1 s
Min
1.1
Typ.
1.27
30
5
Max
1.4
10
1
7
Unit
V
µA
pF
nA
pF
9.
9.
9.
9. Coupled Electrical Characteristics (Unless otherwise specified, T
Coupled Electrical Characteristics (Unless otherwise specified, T
Coupled Electrical Characteristics (Unless otherwise specified, T
Coupled Electrical Characteristics (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
Characteristics
Trigger LED current
Return LED current
ON-state resistance
Symbol
IFT
IFC
RON
Note Test Condition
ION = 100 mA
IOFF = 10 µA
ION = 120 mA, IF = 5 mA, t < 1 s
Min
0.1
Typ.
7
Max
3
12
Unit
mA
Ω
10.
10.
10.
10. Isolation Characteristics (Unless otherwise specified, T
Isolation Characteristics (Unless otherwise specified, T
Isolation Characteristics (Unless otherwise specified, T
Isolation Characteristics (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
Characteristics
Total capacitance (input to output)
Isolation resistance
Isolation voltage
Symbol
CS
RS
BVS
Note
(Note 1)
(Note 1)
(Note 1)
Test Condition
VS = 0 V, f = 1 MHz
VS = 500 V, R.H. ≤ 60 %
AC, 60 s
AC, 1 s in oil
DC, 60 s, in oil
Min
500
Typ.
1.0
1014
1000
1000
Max
Unit
pF
Ω
Vrms
Vdc
Note 1: This device is considered as a two-terminal device: Pins 1 and 2 are shorted together, and pins 3 and 4 are
shorted together.
11.
11.
11.
11. Switching Characteristics (Unless otherwise specified, T
Switching Characteristics (Unless otherwise specified, T
Switching Characteristics (Unless otherwise specified, T
Switching Characteristics (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
Characteristics
Turn-on time
Turn-off time
Symbol
tON
tOFF
Note Test Condition
See Fig. 11.1.
RL = 200 Ω, VDD = 20 V, IF = 5 mA
See Fig. 11.1.
RL = 200 Ω, VDD = 20 V, IF = 10 mA
See Fig. 11.1.
RL = 200 Ω, VDD = 20 V, IF = 5 mA
See Fig. 11.1.
RL = 200 Ω, VDD = 20 V, IF = 10 mA
Min
Typ.
Max
500
250
200
200
Unit
µs
Fig.
Fig.
Fig.
Fig. 11.1
11.1
11.1
11.1 Switching Time Test Circuit and Waveform
Switching Time Test Circuit and Waveform
Switching Time Test Circuit and Waveform
Switching Time Test Circuit and Waveform
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
4
12.
12.
12.
12. Characteristics Curves (Note)
Characteristics Curves (Note)
Characteristics Curves (Note)
Characteristics Curves (Note)
Fig.
Fig.
Fig.
Fig. 12.1
12.1
12.1
12.1 I
I
I
IF
F
F
F - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.2
12.2
12.2
12.2 I
I
I
ION
ON
ON
ON - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.3
12.3
12.3
12.3 I
I
I
IF
F
F
F - V
- V
- V
- VF
F
F
FFig.
Fig.
Fig.
Fig. 12.4
12.4
12.4
12.4 I
I
I
ION
ON
ON
ON - V
- V
- V
- VON
ON
ON
ON
Fig.
Fig.
Fig.
Fig. 12.5
12.5
12.5
12.5 R
R
R
RON
ON
ON
ON - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.6
12.6
12.6
12.6 I
I
I
IFT
FT
FT
FT - T
- T
- T
- Ta
a
a
a
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
5
Fig.
Fig.
Fig.
Fig. 12.7
12.7
12.7
12.7 t
t
t
tON
ON
ON
ON, t
, t
, t
, tOFF
OFF
OFF
OFF - I
- I
- I
- IF
F
F
FFig.
Fig.
Fig.
Fig. 12.8
12.8
12.8
12.8 t
t
t
tON
ON
ON
ON, t
, t
, t
, tOFF
OFF
OFF
OFF - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.9
12.9
12.9
12.9 I
I
I
IOFF
OFF
OFF
OFF - V
- V
- V
- VOFF
OFF
OFF
OFF Fig.
Fig.
Fig.
Fig. 12.10
12.10
12.10
12.10 I
I
I
IOFF
OFF
OFF
OFF - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.11
12.11
12.11
12.11 C
C
C
COFF
OFF
OFF
OFF/C
/C
/C
/COFF
OFF
OFF
OFF(0 V) - V
(0 V) - V
(0 V) - V
(0 V) - VOFF
OFF
OFF
OFF
Note: The above characteristics curves are presented for reference only and not guaranteed by production test,
unless otherwise noted.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
6
13.
13.
13.
13. Soldering and Storage
Soldering and Storage
Soldering and Storage
Soldering and Storage
13.1.
13.1.
13.1.
13.1. Precautions for Soldering
Precautions for Soldering
Precautions for Soldering
Precautions for Soldering
The soldering temperature should be controlled as closely as possible to the conditions shown below.
• When using soldering reflow
(See the figure shown below, which is based on the package surface temperature.)
Reflow soldering may be performed up to twice.
The first reflow soldering should be performed within 168 hours after opening the moisture-proof
packaging.
The second reflow soldering must be performed within 168 hours of the first reflow.
• When using soldering Iron
Complete soldering within 10 seconds for lead temperature not exceeding 260 .
Heating by soldering iron must be done only once per lead.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
7
13.2.
13.2.
13.2.
13.2. Precautions for General Storage
Precautions for General Storage
Precautions for General Storage
Precautions for General Storage
• Avoid storage locations where devices may be exposed to moisture or direct sunlight.
• Do not store the products in locations with poisonous gases (especially corrosive gases) or in dusty
conditions.
• Store the products in locations with minimal temperature fluctuations. Rapid temperature changes during
storage can cause condensation, resulting in lead oxidation or corrosion, which will deteriorate the
solderability of the leads.
• Do not allow loads to be applied directly to devices while they are in storage.
• If devices have been stored for more than two years under normal storage conditions, it is recommended
that you check the leads for ease of soldering prior to use.
• Follow the precautions printed on the packing label of the device for transportation and storage.
• Thermal stress may cause a crack in surface-mount products during surface-mount assembly if they have
absorbed atmospheric moisture. To prevent a crack, please observe the following precautions.
1. Moisture-proof bags may be stored unopened for up to 12 months under the following conditions.
Temperature: 5 to 30
Humidity: 90 % (max)
2. After opening the moisture-proof bag, the devices should be assembled within 168 hours in an
environment of 5 to 30 /70 %RH or below.
3. If, upon opening, the moisture indicator card shows a humidity of 30 % or above (i.e., has turned
pink) or the expiration date has passed, the devices should be baked in tape and reel.
After baking, use the baked devices within 72 hours, but perform baking only once.
Baking conditions: 60±5 , for 64 to 72 hours.
Expiration date: 12 months from the sealing date, which is imprinted on the label affixed.
4. Repeated baking can affect the peeling strength of taping and cause a trouble during mounting.
Furthermore, protect the devices against static electricity for baking.
5. If the laminated packing material is broken, its hermeticity deteriorates. Therefore, do not throw or
drop the packed devices.
6. When restoring devices after removal from their packing, use anti-static containers.
14.
14.
14.
14. Land Pattern Dimensions (for reference only)
Land Pattern Dimensions (for reference only)
Land Pattern Dimensions (for reference only)
Land Pattern Dimensions (for reference only)
Unit: mm
Unit: mm
Unit: mm
Unit: mm
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
8
15.
15.
15.
15. Marking
Marking
Marking
Marking
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
9
16.
16.
16.
16. Embossed-Tape Packing (TP) Specification for Mini-Flat Photorelays
Embossed-Tape Packing (TP) Specification for Mini-Flat Photorelays
Embossed-Tape Packing (TP) Specification for Mini-Flat Photorelays
Embossed-Tape Packing (TP) Specification for Mini-Flat Photorelays
16.1.
16.1.
16.1.
16.1. Applicable Package
Applicable Package
Applicable Package
Applicable Package
Package Name
VSON4
Product Type
Photorelay
16.2.
16.2.
16.2.
16.2. Product Naming Conventions
Product Naming Conventions
Product Naming Conventions
Product Naming Conventions
Type of package used for shipment is denoted by a symbol suffix after a part number. The method of classification
is as below.
Example) TLP3417(TP,F
Part number: TLP3417
Tape type: TP
[[G]]/RoHS COMPATIBLE: F (Note 1)
(Note 1)
(Note 1)
(Note 1)
Note 1: Please contact your Toshiba sales representative for details on environmental information such as the product's
RoHS compatibility.
RoHS is the Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical and electronic equipment.
16.3.
16.3.
16.3.
16.3. Tape Dimensions Specification
Tape Dimensions Specification
Tape Dimensions Specification
Tape Dimensions Specification
Tape Type
TP
Division
Packing Amount
(A unit per reel)
3000
16.3.1.
16.3.1.
16.3.1.
16.3.1. Orientation of Device in Relation to Direction of Feed
Orientation of Device in Relation to Direction of Feed
Orientation of Device in Relation to Direction of Feed
Orientation of Device in Relation to Direction of Feed
Device orientation in the carrier cavities as shown in the following figure.
Fig.
Fig.
Fig.
Fig. 16.3.1.1
16.3.1.1
16.3.1.1
16.3.1.1 Device Orientation
Device Orientation
Device Orientation
Device Orientation
16.3.2.
16.3.2.
16.3.2.
16.3.2. Empty Cavities
Empty Cavities
Empty Cavities
Empty Cavities
Characteristics
Occurrences of 2 or more
successive empty cavities
Single empty cavity
Criterion
0 device
6 devices (max) per reel
Remarks
Within any given 40-mm section of tape, not including leader
and trailer
Not including leader and trailer
16.3.3.
16.3.3.
16.3.3.
16.3.3. Tape Leader and Trailer
Tape Leader and Trailer
Tape Leader and Trailer
Tape Leader and Trailer
The start end of the tape has 40 or more empty cavities. The hub end of the tape has 40 or more empty cavities
and one-third empty turn only for a cover tape.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
10
16.3.4.
16.3.4.
16.3.4.
16.3.4. Tape Dimensions
Tape Dimensions
Tape Dimensions
Tape Dimensions
Tape material: Plastic (for protection against static electricity)
Table
Table
Table
Table Tape Dimensions (unit: mm, tolerance:
Tape Dimensions (unit: mm, tolerance:
Tape Dimensions (unit: mm, tolerance:
Tape Dimensions (unit: mm, tolerance: ±
±
±
±0.1)
0.1)
0.1)
0.1)
Symbol
A
B
D
E
F
G
K0
Dimension
1.6
3.0
3.5
1.75
4.0
4.0
1.5
Remark
Center line of embossed cavity and sprocket hole
Distance between tape edge and sprocket hole center
Cumulative error +0.2/-0.2 per 10 empty cavities holes
Cumulative error +0.2/-0.2 per 10 sprocket holes
Internal space
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
11
16.3.5.
16.3.5.
16.3.5.
16.3.5. Reel Specification
Reel Specification
Reel Specification
Reel Specification
Material: Plastic (for protection against static electricity)
Table
Table
Table
Table Reel Dimensions (unit: mm)
Reel Dimensions (unit: mm)
Reel Dimensions (unit: mm)
Reel Dimensions (unit: mm)
Symbol
A
B
C
E
U
W1
W2
Dimension
φ180 ± 3
φ60 ± 1
φ13 ± 0.5
2.0 ± 0.5
4.0 ± 0.5
9.0 ± 0.3
11.4 ± 1.0
16.4.
16.4.
16.4.
16.4. Packing (Note)
Packing (Note)
Packing (Note)
Packing (Note)
Fig.
Fig.
Fig.
Fig. 16.4.1
16.4.1
16.4.1
16.4.1 1 reel/carton (unit: mm)
1 reel/carton (unit: mm)
1 reel/carton (unit: mm)
1 reel/carton (unit: mm)
Note: Taping reel diameter: φ180 mm
16.5.
16.5.
16.5.
16.5. Label Format
Label Format
Label Format
Label Format
The carton bears a label indicating the product number, the symbol representing classification of standard, the
quantity, the lot number and the Toshiba company name.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
12
16.6.
16.6.
16.6.
16.6. Ordering Information
Ordering Information
Ordering Information
Ordering Information
When placing an order, please specify the part number, tape type and quantity as shown in the following example.
Example) TLP3417(TP,F 3000 pcs
Part number: TLP3417
Tape type: TP
[[G]]/RoHS COMPATIBLE: F (Note 1)
(Note 1)
(Note 1)
(Note 1)
Quantity (must be a multiple of 3000): 3000 pcs
Note 1: Please contact your Toshiba sales representative for details on environmental information such as the product's
RoHS compatibility.
RoHS is the Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical and electronic equipment.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
13
Package Dimensions
Package Dimensions
Package Dimensions
Package Dimensions
Unit: mm
Weight: 10 mg (typ.)
Package Name(s)
TOSHIBA: 11-2D1A
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
TLP3417
14
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
Toshiba Corporation and its subsidiaries and affiliates are collectively referred to as "TOSHIBA".
Hardware, software and systems described in this document are collectively referred to as "Product".
• TOSHIBA reserves the right to make changes to the information in this document and related Product without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's
written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible
for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which
minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage
to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate
the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA
information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the
precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application
with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications,
including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating
and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample
application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE").
("UNINTENDED USE").
("UNINTENDED USE").
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation,
equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles,
trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices,
elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales
representative.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any
intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor.
Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation,
for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products
(mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and
regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration
Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all
applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
2018-05-10
Rev.8.0
©2016-2018
Toshiba Electronic Devices & Storage Corporation
