AS5000 PROGRAMMER - AMS AG - Datasheet.World

austriamicrosystems AG

is now

ams AG

The technical content of this austriamicrosystems document is still valid.

Contact information:

Headquarters:

ams AG

Tobelbaderstrasse 30

8141 Unterpremstaetten, Austria

Tel: +43 (0) 3136 500 0

e-Mail: ams_sales@ams.com

Please visit our website at www.ams.com

Revision 1.10, 04-Mar-2010 Page 1 of 24

www.austriamicrosystems.com

1 General Overview

This operational manual describes the function of the AS5000 Programmer in combination with the programming

boards. This tool can program the austriamicrosystems AS5000 series magnetic rotary encoders. The graphical user

interface (GUI) runs on PC running Windows XP or later and controls the programmer via the USB interface.

All major access modes to the OTP memories can be established. Be aware that austriamicrosystems provides the

AS5000 Programmer as a reference for programming and reading of mentioned devices (refer to Appendix A) under

laboratory conditions (no warranty for mass production).

Note: Since firmware version v2.10 the AS5000-Programmer contains a boot loader, which provides an update function

for new software release. Please refer to the corresponding application note AN5000-60 (available on our

webpage).

2 Hardware Components

2.1 Description of the Hardware Components

Figure 1: Three components of the Programmer solution

Figure 1 shows the three components which are needed to program the austriamicrosystems magnetic rotary encoder.

Take care that the connector between programming box and programming box is plugged in the right way.

Warning:

In case of wrong connection, the components in the AS5000 programmer or the encoder can be destroyed!

AS5000 Programmer

Programming Tool

OPERATION MANUAL

USB cable

AS5000 programmer

Programming board

(AS5xxx-PB)

LCD display

(programmer v1.3 or older only)

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 2 of 24

www.austriamicrosystems.com

Figure 2: AS5000 Programmer M RE co nn ector (right side view)

Pin # Signal Comment

1 Vzap Programming voltage

2 Vzap Programming voltage

3 D10 Encoder signal

4 ADC2 Device autodetection voltage

5 D9 Encoder signal

6 ADC1 Vzap feedback

7 D8 Encoder signal

8 D11 Encoder signal

9 D7 Encoder signal

10 D6 Encoder signal

11 VDD Encoder power supply

12 VDD Encoder power supply

13 GND Ground

14 GND Ground

15 D5 Encoder signal

16 D0 Encoder & LCD display signal

17 D4 Encoder signal

18 D1 LCD signal – Do not use

19 D3 Encoder & LCD display signal

20 D2 Encoder & LCD display signal

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 3 of 24

www.austriamicrosystems.com

2.2 Description of the programming board

Figure 3: Example for an AS5043-PB Programming board

The programming board (AS5xxx-PB) is specific for a group of devices. By jumper setting on this board the build in

firmware in the programming box automatically detects the selected device. It is not recommended to change the

jumper setting to a different encoder type than installed in the socket.

To place or remove a device form the socket, push the black frame of the socket down. This socket has more

connectors as the AS50xx/ AS51xx part and therefore it is important to align the device to the left side of the socket.

The pin 1 of the device must be on the bottom left side. Figure 2 shows the detailed placed device in the socket.

The jumper J9 is specific for the AS5043/AS5143. This Jumper is used to close the feedback loop used for the analog

output operation mode. With this jumper the gain can set to 1.

The jumper J6 is by default closed because the AS5000 Programmer provides 3.3V operation. In case of 5 V operation

the jumper must be removed and the configuration can be changed over the GUI.

ZIF socket

Jumper J9:

Gain = 1

(AS5043 only)

Device Selection

jumper

Jumper J6:

Supply voltage selection

Open: 5V – Close: 3.3V (default)

Connector to the

AS5000 programmer

Location of pin 1 of

the encoder

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 4 of 24

www.austriamicrosystems.com

3 Installation

3.1 Hardware setup

First connect the AS5xxx-PB to the 20-pin connector of the AS5000 Programmer, as shown on Figure 1.

The AS5000 Programmer is directly powered by the PC via USB. An external power supply is not needed.

3.2 Installing the GUI on the PC

The preliminary software is developed for a Microsoft Windows XP operating system with Service Pack 2. In addition

the dotnet (.NET) framework version 2.0 or more must be installed on the PC. This package can be downloaded free of

charge from the Microsoft webpage:

http://www.microsoft.com/downloads/details.aspx?FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5&displaylang=en

Following Procedure is recommended before starting the GUI:

1. check on your PC if Service Pack 2 is installed

2. install the mentioned .net package to your computer

3. execute AS5000GUI_setup.exe

4. Finally start the GUI using the shortcut in the start menu or desktop.

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 5 of 24

www.austriamicrosystems.com

4 Graphical User Interface (GUI)

Figure 4: Main window of the GUI, no PB board inserted

Figure 4 shows the main window of the GUI.

In the top left corner, informations about the connected hardware are displayed:

- firmware (FW) type of the connected hardware: ubox (AS5000 Programmer) or dbrd (Demoboard)

- firmware (FW) version

By default the GUI is in the auto detection mode. Any austriamicrosystems device connected on the USB port (one

device at the same time) will be automatically detected and displayed in the right top corner.

Note: The autodetect mode can be disabled and forced to any other device type by selecting the device manually.

Once a PB board inserted, tabs will be displayed allowing go into two main sections: SSI (or TWI) and OTP.

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 6 of 24

www.austriamicrosystems.com

4.1 Programming the AS5040/AS5045/AS5140/AS5145

Programming AS5040/AS5140 encoders requires the

AS5040-PB ZIF socket board. This adapter is compatible

with AS5040, AS5140, AS5045 and AS5145.

Jumper J6 must be close for normal operation and

programming operation.

Figure 5: AS5040-PB Programming bo ard

By selecting the SSI tab, information of the angular position and the status bits appear:

Figure 6: SS I tab with AS 5040 encoder in serted in AS5040-P B

- Die selection: This option is for dual die AS52xx devices only. For AS50xx and AS51xx devices Die 0 (default)

must be selected.

- Value field is the raw angle extracted from the SSI stream. The angle range is 0 (0°) to 1023 (359.6°)

- Status field displays the status bits extracted from the SSI stream. Green light means that the airgap between

the magnet and encoder is correct. Orange light means the magnet is too close of too far.

- CCW checkbox is the angle direction. To invert the rotating direction, check CCW.

- Zero Position field: Set button writes the actual angle value into the Zero Position register of the encoder. This

programming is not permanent. The actual value will be 0 after zero position programming. To reset the zero

position register, or to set a new zero position, click on Reset first.

- Read interval is the SSI stream readout and refresh rate the GUI.

AS5040

PB ZIF socket

board

Device selection for autodetect:

- Jumper position 2: AS5040

- Jumper position 3: AS5045

- Jumper position 4: AS5140

- Jumper position 5: AS5145

Position of the magnet

Status bits and field alarm

Set the actual angle as

Zero Position

Counter Clockwise mode

Selected die

(dual die AS52xx devices only)

Pin 1

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 7 of 24

www.austriamicrosystems.com

Figure 7: AS5040 SSI tab after Zero P osition progr amming

This example is the effect when the function Zero Position SET has been performed.

Before programming, the encoder shows the position 651 (Figure 6). One click on Zero Position Set makes the software

writing the value 651 into the OTP Zero Position register (not permanent programming).

Selecting Zero Position Reset will write the value 0 to the OTP Zero Position register.

Note: The Zero Position function is the same for all the AS50xx, AS51xx, AS52xx rotary encoders offering this feature.

Selecting the OTP tab will read the OTP configuration from the IC.

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 8 of 24

www.austriamicrosystems.com

Figure 8: OTP t ab of an unprogrammed AS5040

AS5040/AS5045:

Read reads the OTP configuration from the permanent fuse register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is possible

to check the effect of the new configuration.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

AS5140/AS5145:

Load reads the OTP configuration from the permanent fuse register.

Read reads the OTP configuration from the volatile register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is possible

to check the effect.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 9 of 24

www.austriamicrosystems.com

4.2 Programming the AS5043

Programming AS5043 encoders requires the AS5043-PB

ZIF socket board.

Jumper J6 must be close for normal operation and

programming operation.

Figure 9: AS5043-PB Programming bo ard

By selecting the SSI tab, information of the angular position and the status bits appear:

Figure 10: SSI tab with AS5043 insert ed in AS5043-PB

- Die selection: This option is for dual die AS52xx devices only. For AS50xx and AS51xx devices Die 0 (default)

must be selected.

- Value field is the raw angle extracted from the SSI stream. The angle range is 0 (0°) to 1023 (359.6°)

- Status field displays the status bits extracted from the SSI stream. Green light means that the airgap between the

magnet and encoder is correct. Orange light means the magnet is too close of too far.

- CCW checkbox is the angle direction. To invert the rotating direction, check CCW.

- Zero Position field: Set button writes the actual angle value into the Zero Position register of the encoder. This

programming is not permanent. The actual value will be 0 after zero position programming. To reset the zero

position register, or to set a new zero position, click on Reset first.

- Read interval is the SSI stream readout and refresh rate the GUI.

Position of the magnet

Status bits and field alarm

Set the actual angle as

Zero Position

Counter C

lockwise mode

Selected die

(dual die AS52xx devices only)

AS504

PB ZIF socket board

Device selection for autodetect:

- Jumper position 1: AS5043

Pin 1

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 10 of 24

www.austriamicrosystems.com

Figure 11: O TP tab of AS5043, with FBintEN option checked by user

• AS5043:

Read reads the OTP configuration from the permanent fuse register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is

possible to check the effect of the new configuration.

Zap! Writes permanently the checked OTP bits to the encoder’s fuses.

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 11 of 24

www.austriamicrosystems.com

4.3 Programming the AS5245

Figure 12: AS5245-PB Pro gramming board

Programming AS5245 encoders requires the AS5245-PB

socket board.

Jumper J6 (J6+J8 for AS5245) must be close for normal

operation and programming operation.

By selecting the SSI tab, information of the angular position and the status bits appear:

Figure 13: SSI tab with AS5045 insert ed in AS5040-PB

- Die selection: This option is for dual die AS52xx devices only. For AS50xx and AS51xx devices Die 0 (default)

must be selected.

- Value field is the raw angle extracted from the SSI stream. The angle range is 0 (0°) to 1023 (359.6°)

- Status field displays the status bits extracted from the SSI stream. Green light means that the airgap between

the magnet and encoder is correct. Orange light means the magnet is too close of too far.

- CCW checkbox is the angle direction. To invert the rotating direction, check CCW.

Position of the magnet

Status bits and field alarm

Set the actual angle as

Zero Position

Counter Clockwise mode

Selected die

(dual die AS52xx devices only)

Pin 1

AS5245

PB ZIF socket

board

Device selection for autodetect:

- Jumper position 2: AS5245

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 12 of 24

www.austriamicrosystems.com

- Zero Position field: Set button writes the actual angle value into the Zero Position register of the encoder. This

programming is not permanent. The actual value will be 0 after zero position programming. To reset the zero

position register, or to set a new zero position, click on Reset first.

- Read interval is the SSI stream readout and refresh rate the GUI.

Figure 14: O TP tab of AS5045

• AS5245:

Load reads the OTP configuration from the permanent fuse register.

Read reads the OTP configuration from the volatile register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is

possible to check the effect.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

Selected die

(dual die AS52xx devices only)

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 13 of 24

www.austriamicrosystems.com

4.4 Programming the AS5134

Figure 15: AS5134-PB Pro gramming Board

Programming AS5134 encoders requires the AS5134-PB

socket board.

Figure 16: G UI for the AS5134

- Value field is the raw angle extracted from the interface. The angle range is 0° to 359°

- Status field (AGC) displays the status bits depending on the set AGC values. Green light means that the

airgap between the magnet and encoder is correct. Red light means the magnet is too far away.

- Zero Position field: Set button writes the actual angle value into the Zero Position register of the encoder. This

programming is not permanent. The actual value will be 0 after zero position programming. To reset the zero

position register, or to set a new zero position, click on Reset first.

- Read interval is the readout and refresh rate the GUI.

- Digital interface opens an additional window (see Figure 17), which provides all communications commands

like WRTIE_CONFIG or EN_PROG (for entering the exentended mode).

Multi Turn Counter

Additional window for the BLDC output signals

AGC value

AS5

134

PB ZIF socket board

Device selection:

- Jumper position 1: AS5134

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 14 of 24

www.austriamicrosystems.com

Figure 17: Communication command window

Figure 18: O TP tab of AS5134

• AS5134:

Read reads the OTP configuration from the permanent fuse register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is

possible to check the effect of the new configuration.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

Analog Readback is not implemented yet. It will be available soon.

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 15 of 24

www.austriamicrosystems.com

4.5 Programming the AS5163/AS5263

Figure 19: AS5x63-CB Connection Board (left) and AS5163-PB Programmin g Board (righ t)

Programming AS5163/AS5263 encoders requires the AS5163-PB/AS5263-PB socket board and the AS5x63-CB

connection board.

The connection board provides the load, needed for programming and operating the AS5163/AS5263.

Further details concerning all programming options are provided in application note AN5163-10 (available on our

webpage).

4.6 Programming the AS5115/AS5215

Figure 20: AS115-PB Programming Board ( left) and AS5215-PB Progr amming Bo ard (r ight)

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 16 of 24

www.austriamicrosystems.com

Figure 21: TWI tab of AS 5115

The AS5115-PB and AS5215-PB does not support an angle readback of the analogue outputs.

Figure 22: O TP tab of AS5115

• AS5115/AS5215:

Read reads the OTP configuration from the permanent fuse register.

Write writes the bits checked by the user into the volatile OTP register. Selecting the SSI after the configuration is

possible to check the effect of the new configuration.

Zap! writes permanently the checked OTP bits to the encoder’s fuses.

Selected die

(dual die AS52xx devices only)

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 17 of 24

www.austriamicrosystems.com

5 Programming boards (PB) Schematics

5.1 AS5040-PB-1.1

5.2 AS5043-PB-1.1

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 18 of 24

www.austriamicrosystems.com

5.3 AS5115-PB1.1

5.4 AS5134-PB-1.1

5.5 AS5163-PB-1.0

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 19 of 24

www.austriamicrosystems.com

5.6 AS5215-PB-1.1

5.7 AS5245-PB-1.1

5.8 AS5263-PB-1.0

ams AG

Technical content still valid

Revision 1.10, 04-Mar -2010 Page 20 of 24

www.aus triamicr osystems.com

Appendix A

Programming

Board

Part

number

AS5030

AS5040

AS5043

AS5115

AS5130

AS5134

AS5163

AS5215

AS5245

AS5263

Supported by

firmware

≥

AS5030

●

Future Release

AS5040

●

0.12

AS5043

●

0.12

AS5045

●

0.12

AS5046

●

Future Release

AS5115

●

2.24

AS5130

●

Future Release

AS5134

●

0.10

AS5140

●

0.10

AS5145

●

0.10

AS5163

●

0.13

AS5215

●

2.24

AS5245

●

0.10

AS5263

●

0.13

ams AG

Technical content still valid

Revision 1.10, 04-Mar-2010 Page 21 of 24

www.austriamicrosystems.com

Index

1 General Overview...................................................................................................................................................... 1

2 Hardware Components.............................................................................................................................................. 1

2.1 Description of the Hardware Components........................................................................................................ 1

2.2 Description of the programming board..............................................................................................................3

3 Installation .................................................................................................................................................................4

3.1 Hardware setup................................................................................................................................................. 4

3.2 Installing the GUI on the PC .............................................................................................................................4

4 Graphical User Interface (GUI)..................................................................................................................................5

4.1 Programming the AS5040/AS5045/AS5140/AS5145 ....................................................................................... 6

4.2 Programming the AS5043.................................................................................................................................9

4.3 Programming the AS5245...............................................................................................................................11

4.4 Programming the AS5134...............................................................................................................................13

4.5 Programming the AS5163/AS5263.................................................................................................................15

4.6 Programming the AS5115/AS5215.................................................................................................................15

5 Programming boards (PB) Schematics ...................................................................................................................17

5.1 AS5040-PB-1.1...............................................................................................................................................17

5.2 AS5043-PB-1.1...............................................................................................................................................17

5.3 AS5115-PB1.1 ................................................................................................................................................18

5.4 AS5134-PB-1.1...............................................................................................................................................18

5.5 AS5163-PB-1.0...............................................................................................................................................18

5.6 AS5215-PB-1.1...............................................................................................................................................19

5.7 AS5245-PB-1.1...............................................................................................................................................19

5.8 AS5263-PB-1.0...............................................................................................................................................19

Appendix A ....................................................................................................................................................................... 20

Revision History ...............................................................................................................................................................22

Contact ............................................................................................................................................................................. 23

Sales Offices................................................................................................................................................................ 23

Copyright .......................................................................................................................................................................... 24

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 22 of 24

www.austriamicrosystems.com

Revision History

Revision Date Description

R1.0 March.29, 2008 New copy

R1.1 May 22, 2008 All paragraphs, new pictures included

R1.2 June 16, 2008 AS5134 device added

R1.3 September 4, 2008 New devices added, minor corrections

R1.4 September 26, 2008 Minor corrections

R1.5 December 15, 2008 Minor corrections

R1.6 January 26, 2009 Layout modification, PB schematics

R1.7 March 3, 2009 Supported devices table added

R1.8 August 10, 2009 AS5x40, AS5x45 chapter added, screenshot updated.

R1.9 February 04, 2010 AS5134 updated, AS5143 removed, AS5245 added

R1.10 March 04, 2010 AS5115, AS5215, AS5163 and AS5263 added

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 23 of 24

www.austriamicrosystems.com

Contact

Headquarters

austriamicrosystems AG

A 8141 Schloss Premstätten, Austria

Phone: +43 3136 500 0

Fax: +43 3136 525 01

industry.medical@austriamicrosystems.com

www.austriamicrosystems.com

Sales Offices

austriamicrosystems Germany GmbH

Tegernseer Landstrasse 85

D-81539 München, Germany

Phone: +49 89 69 36 43 0

Fax: +49 89 69 36 43 66

austriamicrosystems Italy S.r.l.

Via A. Volta, 18

I-20094 Corsico (MI), Italy

Phone: +39 02 4586 4364

Fax: +39 02 4585 773

austriamicrosystems France S.A.R.L.

124, Avenue de Paris

F-94300 Vincennes, France

Phone: +33 1 43 74 00 90

Fax: +33 1 43 74 20 98

austriamicrosystems Switzerland AG

Rietstrasse 4

CH 8640 Rapperswil, Switzerland

Phone: +41 55 220 9008

Fax: +41 55 220 9001

austriamicrosystems UK, Ltd.

88, Barkham Ride,

Finchampstead, Wokingham

Berkshire RG40 4ET, United Kingdom

Phone: +44 118 973 1797

Fax: +44 118 973 5117

austriamicrosystems AG

Klaavuntie 9 G 55

FI 00910 Helsinki, Finland

Phone: +358 9 72688 170

Fax: +358 9 72688 171

austriamicrosystems AG

Bivägen 3B

S 19163 Sollentuna, Sweden

Phone: +46 8 6231 710

austriamicrosystems USA, Inc.

8601 Six Forks Road

Suite 400

Raleigh, NC 27615, USA

Phone: +1 919 676 5292

Fax: +1 509 696 2713

austriamicrosystems USA, Inc.

4030 Moorpark Ave

Suite 116

San Jose, CA 95117, USA

Phone: +1 408 345 1790

Fax: +1 509 696 2713

austriamicrosystems AG

Suite 811, Tsimshatsui Centre

East Wing, 66 Mody Road

Tsim Sha Tsui East, Kowloon, Hong Kong

Phone: +852 2268 6899

Fax: +852 2268 6799

austriamicrosystems AG

AIOS Gotanda Annex 5th Fl., 1-7-11,

Higashi-Gotanda, Shinagawa-ku

Tokyo 141-0022, Japan

Phone: +81 3 5792 4975

Fax: +81 3 5792 4976

austriamicrosystems AG

#805, Dong Kyung Bldg.,

824-19, Yeok Sam Dong,

Kang Nam Gu, Seoul

Korea 135-080

Phone: +82 2 557 8776

Fax: +82 2 569 9823

austriamicrosystems AG

Singapore Representative Office

83 Clemenceau Avenue, #02-01 UE Square

239920, Singapore

Phone: +65 68 30 83 05

Fax: +65 62 34 31 20

ams AG

Technical content still valid

AS5000 Pr ogr ammer OPERATIONAL MANUAL

Revision 1.10, 04-March-2010 Page 24 of 24

www.austriamicrosystems.com

Devices sold by austriamicrosystems are covered by the warranty and patent indemnification provisions appearing in its

Term of Sale. austriamicrosystems makes no warranty, express, statutory, implied, or by description regarding the

information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems

reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this

product into a system, it is necessary to check with austriamicrosystems for current information. This product is intended for

use in normal commercial applications.

reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. To the

best of its knowledge, austriamicrosystems asserts that the information contained in this publication is accurate and correct.

However, austriamicrosystems shall not be liable to recipient or any third party for any damages, including but not limited to

personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or

consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical

data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems rendering of

technical or other services.

ams AG

Technical content still valid