SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
Copyright 1995, Texas Instruments Incorporated
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
•Local Bus-Latch Capability
•Choice of True or Inverting Logic
•Package Options Include Plastic
Small-Outline (DW) Packages and Standard
Plastic (N) 300-mil DIPs
DEVICE OUTPUT LOGIC
SN74ALS620A 3 state Inverting
SN74ALS621A Open collector T rue
SN74ALS623A, SN74AS623 3 state T rue
description
These octal bus transceivers are designed for asynchronous two-way communication between data buses. The
control-function implementation allows for maximum flexibility in timing.
These devices allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending
upon the logic levels at the output-enable (OEAB and OEBA) inputs.
The output-enable inputs disable the device so that the buses are effectively isolated. The dual-enable
configuration gives the transceivers the capability to store data by simultaneously enabling OEAB and OEBA .
Each output reinforces its input in this transceiver configuration. When both OEAB and OEBA are enabled and
all other data sources to the two sets of bus lines are in the high-impedance state, both sets of bus lines (16 total)
remain at their last states. The 8-bit codes appearing on the two sets of buses are identical for the
SN74ALS621A, SN74ALS623A, and SN74AS623 or complementary for the SN74ALS620A.
The -1 versions of the SN74ALS620A and SN74ALS621A are identical to the standard versions, except that
the recommended maximum IOL is increased to 48 mA in the -1 versions.
The SN74ALS620A, SN74ALS621A, SN74ALS623A, and SN74AS623 are characterized for operation from
0°C to 70°C.
FUNCTION TABLE
INPUTS OPERATION
OEBA OEAB SN74ALS620A SN74ALS621A
SN74ALS623A
SN74AS623
L L B data to A bus B data to A bus
HHA data to B bus A data to B bus
H L Isolation Isolation
L H B data to A bus,
A data to B bus B data to A bus,
A data to B bus
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
OEAB
A1
A2
A3
A4
A5
A6
A7
A8
GND
VCC
OEBA
B1
B2
B3
B4
B5
B6
B7
B8
DW OR N PACKAGE
(TOP VIEW)
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
logic symbols†
2
EN1
19
EN2
1
OEAB
2
A1 B1
18
OEBA
1
SN74ALS620A
2
EN1
19
EN2
1
OEAB
2
A1
3
A2
B1
18
4
A3 5
A4 6
A5 7
A6 8
A7 9
A8
B2
17
B3
16
B5
14 B4
15
B6
13
B8
11 B7
12
OEBA
1
SN74ALS621A
2
EN1
19
EN2
1
OEAB
2
A1
3
A2
B1
18
4
A3 5
A4 6
A5 7
A6 8
A7 9
A8
B2
17
B3
16
B5
14 B4
15
B6
13
B8
11 B7
12
OEBA
1
SN74ALS623A, SN74AS623
3
A2 B2
17
4
A3 B3
16
5
A4 B4
15
6
A5 B5
14
7
A6 B6
13
8
A7 B7
12
9
A8 B8
11
†These symbols are in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
logic diagrams (positive logic)
A1 B1
To Seven Other T ransceivers
OEBA
OEAB
19
1
18
2
SN74ALS620A SN74ALS621A
SN74ALS623A, SN74AS623
A1 B1
OEBA
OEAB
19
1
182
To Seven Other T ransceivers
A1 B1
To Seven Other T ransceivers
OEBA
OEAB
19
1
18
2
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI: All inputs 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O ports 5.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: SN74ALS620A, SN74ALS623A 0°C to 70°C. . . . . . . . . . . . . . . . .
Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
recommended operating conditions
SN74ALS620A
SN74ALS623A UNIT
MIN NOM MAX
VCC Supply voltage 4.5 5 5.5 V
VIH High-level input voltage 2 V
VIL Low-level input voltage 0.8 V
IOH High-level output current –15 mA
IOL Low-level output current 24 mA
TAOperating free-air temperature 0 70 °C
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER TEST CONDITIONS SN74ALS620A
SN74ALS623A UNIT
MIN TYP†MAX
VIK VCC = 4.5 V, II = –18 mA –1.2 V
VCC = 4.5 V to 5.5 V, IOH = –0.4 mA VCC –2
VOH
VCC =45V
IOH = –3 mA 2.4 3.2 V
V
CC =
4
.
5
V
IOH = –15 mA 2
VOL
VCC =45V
IOL = 12 mA 0.25 0.4
V
V
OL
V
CC =
4
.
5
V
IOL = 24 mA‡0.35 0.5
V
II
Control inputs
VCC =55V
VI = 7 V 0.1
mA
I
IA or B ports
V
CC =
5
.
5
V
VI = 5.5 V 0.1
mA
IIH
Control inputs
VCC =55V
VI=27V
20
µA
I
IH A or B ports§
V
CC =
5
.
5
V
,
V
I =
2
.
7
V
20 µ
A
IIL
Control inputs
VCC =55V
VI=04V
–0.1
mA
I
IL A or B ports§
V
CC =
5
.
5
V
,
V
I =
0
.
4
V
–0.1
mA
IO¶VCC = 5.5 V, VO = 2.25 V –30 –112 mA
Outputs high 24 34
SN74ALS620A VCC = 5.5 V Outputs low 31 44
ICC
Outputs disabled 33 47
mA
I
CC Outputs high 32 43
mA
SN74ALS623A VCC = 5.5 V Outputs low 39 50
Outputs disabled 42 55
†All typical values are at VCC = 5 V, TA = 25°C.
‡Applies only to the -1 version and only if VCC is between 4.75 V and 5.25 V
§For I/O ports, the parameters IIH and IIL include the off-state output current.
¶The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
switching characteristics (see Figure 1)
PARAMETER FROM
(INPUT) TO
(OUTPUT)
VCC = 4.5 V to 5.5 V,
CL = 50 pF,
R1 = 500 Ω,
R2 = 500 Ω,
TA = MIN to MAX†UNIT
SN74ALS620A SN74ALS623A
MIN MAX MIN MAX
tPLH
A
B
210 2 13
ns
tPHL
A
B
2 10 3 11
ns
tPLH
B
A
210 2 13
ns
tPHL
B
A
2 10 3 11
ns
tPZH
OEBA
A
317 5 22
ns
tPZL
OEBA
A
525 5 22
ns
tPHZ
OEBA
A
2 12 2 16
ns
tPLZ
OEBA
A
318 2 19
ns
tPZH
OEAB
B
318 5 22
ns
tPZL
OEAB
B
525 5 22
ns
tPHZ
OEAB
B
2 12 2 16
ns
tPLZ
OEAB
B
318 2 19
ns
†For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡
Supply voltage, VCC 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI: All inputs and I/O ports 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: SN74ALS621A 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
‡Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
recommended operating conditions
SN74ALS621A
UNIT
MIN NOM MAX
UNIT
VCC Supply voltage 4.5 5 5.5 V
VIH High-level input voltage 2 V
VIL Low-level input voltage 0.8 V
VOH High-level output voltage 5.5 V
IOL
Low level out
p
ut current
24 mA
I
OL
Lo
w-
le
v
el
o
u
tp
u
t
c
u
rrent
48§mA
TAOperating free-air temperature 0 70 °C
§Applies only to the -1 version and only if VCC is between 4.75 V and 5.25 V
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
SN74ALS621A
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYP†MAX
UNIT
VIK VCC = 4.5 V, II = –18 mA –1.5 V
IOH VCC = 4.5 V, VOH = 5.5 V 0.1 mA
VOL
VCC =45V
IOL = 24 mA 0.35 0.5
V
V
OL
V
CC =
4
.
5
V
IOL = 48 mA‡0.35 0.5
V
II
Control inputs
VCC =55V
VI = 7 V 0.1
mA
I
IA or B ports
V
CC =
5
.
5
V
VI = 5.5 V 0.1
mA
IIH
Control inputs
VCC =55V
VI=27V
20
µA
I
IH A or B ports§
V
CC =
5
.
5
V
,
V
I =
2
.
7
V
20 µ
A
IIL
Control inputs
VCC =55V
VI=04V
–0.1
mA
I
IL A or B ports§
V
CC =
5
.
5
V
,
V
I =
0
.
4
V
–0.1
mA
ICC
VCC =55V
Outputs high 29 40
mA
I
CC
V
CC =
5
.
5
V
Outputs low 35 48
mA
†All typical values are at VCC = 5 V, TA = 25°C.
‡Applies only to the -1 version and only if VCC is between 4.75 V and 5.25 V
§For I/O ports, the parameters IIH and IIL include the off-state output current.
switching characteristics (see Figure 1)
PARAMETER FROM
(
INPUT
)
TO
(
OUTPUT
)
VCC = 4.5 V to 5.5 V,
CL = 50 pF,
RL = 680 Ω,
TA = MIN to MAX¶UNIT
(INPUT)
(OUTPUT)
SN74ALS621A
MIN MAX
tPLH
A
B
10 33
ns
tPHL
A
B
5 20
ns
tPLH
B
A
10 33
ns
tPHL
B
A
5 20
ns
tPLH
OEBA
A
10 39
ns
tPHL
OEBA
A
12 35
ns
tPLH
OEAB
B
10 39
ns
tPHL
OEAB
B
12 35
ns
¶For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI: All inputs 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O ports 5.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: SN74AS623 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
recommended operating conditions
SN74AS623
UNIT
MIN NOM MAX
UNIT
VCC Supply voltage 4.5 5 5.5 V
VIH High-level input voltage 2 V
VIL Low-level input voltage 0.8 V
IOH High-level output current –15 mA
IOL Low-level output current 64 mA
TAOperating free-air temperature 0 70 °C
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
SN74AS623
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYP‡MAX
UNIT
VIK VCC = 4.5 V, II = –18 mA –1.2 V
VCC = 4.5 V to 5.5 V, IOH = –2 mA VCC –2
VOH
VCC =45V
IOH = –3 mA 2.4 3.2 V
V
CC =
4
.
5
V
IOH = –15 mA 2
VOL VCC = 4.5 V, IOL = 64 mA 0.35 0.55 V
II
Control inputs
VCC =55V
VI = 7 V 0.1
mA
I
IA or B ports
V
CC =
5
.
5
V
VI = 5.5 V 0.1
mA
IIH
Control inputs
VCC =55V
VI=27V
20
µA
I
IH A or B ports§
V
CC =
5
.
5
V
,
V
I =
2
.
7
V
70 µ
A
IIL
Control inputs
VCC =55V
VI=04V
–0.5
mA
I
IL A or B ports§
V
CC =
5
.
5
V
,
V
I =
0
.
4
V
–0.75
mA
IO¶VCC = 5.5 V, VO = 2.25 V –30 –150 mA
Outputs high 57 93
ICC VCC = 5.5 V Outputs low 16 189 mA
Outputs disabled 71 116
‡All typical values are at VCC = 5 V, TA = 25°C.
§For I/O ports, the parameters IIH and IIL include the off-state output current.
¶The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
switching characteristics (see Figure 1)
PARAMETER FROM
(INPUT) TO
(OUTPUT)
VCC = 4.5 V to 5.5 V,
CL = 50 pF,
R1 = 500 Ω,
R2 = 500 Ω,
TA = MIN to MAX†UNIT
SN74AS623
MIN MAX
tPLH
A
B
1 9
ns
tPHL
A
B
1 8
ns
tPLH
B
A
1 9
ns
tPHL
B
A
1 8.5
ns
tPZH
OEBA
A
211
ns
tPZL
OEBA
A
210
ns
tPHZ
OEBA
A
1 7.5
ns
tPLZ
OEBA
A
111.5
ns
tPZH
OEAB
B
211.5
ns
tPZL
OEAB
B
211
ns
tPHZ
OEAB
B
1 7
ns
tPLZ
OEAB
B
1 9
ns
†For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
SN74ALS620A, SN74ALS621A, SN74ALS623A, SN74AS623
OCTAL BUS TRANSCEIVERS
SDAS226A – DECEMBER 1982 – REVISED JANUARY 1995
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
SERIES 54ALS/74ALS AND 54AS/74AS DEVICES
tPHZ
tPLZ
tPHL tPLH
0.3 V
tPZL
tPZH
tPLH tPHL
LOAD CIRCUIT
FOR 3-STATE OUTPUTS
From Output
Under Test Test
Point
R1
S1
CL
(see Note A)
7 V
1.3 V
1.3 V1.3 V
3.5 V
3.5 V
0.3 V
0.3 V
th
tsu
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
Timing
Input
Data
Input
1.3 V 1.3 V 3.5 V
3.5 V
0.3 V
0.3 V
High-Level
Pulse
Low-Level
Pulse
tw
VOLTAGE WAVEFORMS
PULSE DURATIONS
Input
Out-of-Phase
Output
(see Note C)
1.3 V 1.3 V
1.3 V1.3 V
1.3 V 1.3 V
1.3 V1.3 V
1.3 V
1.3 V
3.5 V
3.5 V
0.3 V
0.3 V
VOL
VOH
VOH
VOL
Output
Control
(low-level
enabling)
W aveform 1
S1 Closed
(see Note B)
W aveform 2
S1 Open
(see Note B)
[
0 V
VOH
VOL
[
3.5 V
In-Phase
Output
0.3 V
1.3 V 1.3 V
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS
R2
VCC
RL
Test
Point
From Output
Under Test
CL
(see Note A)
LOAD CIRCUIT
FOR OPEN-COLLECTOR OUTPUTS
LOAD CIRCUIT FOR
BI-STATE
TOTEM-POLE OUTPUTS
From Output
Under Test Test
Point
CL
(see Note A) RL
RL = R1 = R2
NOTES: A. CL includes probe and jig capacitance.
B. W aveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
W aveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. When measuring propagation delay items of 3-state outputs, switch S1 is open.
D. All input pulses have the following characteristics: PRR ≤ 1 MHz, tr = tf = 2 ns, duty cycle = 50%.
E. The outputs are measured one at a time with one transition per measurement.
Figure 1. Load Circuits and Voltage Waveforms
PACKAGE OPTION ADDENDUM
www.ti.com 28-Aug-2010
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
SN74ALS620ADW ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS620ADWE4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS620ADWG4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS620ADWR OBSOLETE SOIC DW 20 TBD Call TI Call TI Samples Not Available
SN74ALS620AN ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS620ANE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS621A-1DW ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS621A-1DWE4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS621A-1DWG4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS621A-1N ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS621A-1NE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS621ADW ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS621ADWE4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS621ADWG4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS621AN ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS621ANE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS623A-1DW OBSOLETE SOIC DW 20 TBD Call TI Call TI Samples Not Available
SN74ALS623A-1DWR OBSOLETE SOIC DW 20 TBD Call TI Call TI Samples Not Available
SN74ALS623A-1N OBSOLETE PDIP N 20 TBD Call TI Call TI Samples Not Available
SN74ALS623ADW ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS623ADWE4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
PACKAGE OPTION ADDENDUM
www.ti.com 28-Aug-2010
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
SN74ALS623ADWG4 ACTIVE SOIC DW 20 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS623AN ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS623AN3 OBSOLETE PDIP N 20 TBD Call TI Call TI Samples Not Available
SN74ALS623ANE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Purchase Samples
SN74ALS623ANSR ACTIVE SO NS 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS623ANSRE4 ACTIVE SO NS 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74ALS623ANSRG4 ACTIVE SO NS 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples
SN74AS623DW OBSOLETE SOIC DW 20 TBD Call TI Call TI Samples Not Available
SN74AS623DWR OBSOLETE SOIC DW 20 TBD Call TI Call TI Samples Not Available
SN74AS623N OBSOLETE PDIP N 20 TBD Call TI Call TI Samples Not Available
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 28-Aug-2010
Addendum-Page 3
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
SN74ALS623ANSR SO NS 20 2000 330.0 24.4 8.2 13.0 2.5 12.0 24.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74ALS623ANSR SO NS 20 2000 367.0 367.0 45.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
