ASMB-MTB0-0A3A2 PLCC-4 Tricolor Black Surface LED Data Sheet Description Features This family of SMT LEDs are in PLCC-4 package. A wide viewing angle together with the built in reflector drives up the intensity of light output making these LEDs suitable for use in interior electronics signs. The black top surface of the LED provides better contrast enhancement, especially in full color display. * Standard PLCC-4 package (Plastic Leaded Chip Carrier) These LEDs are compatible with reflow soldering process. For easy pick & place, the LEDs are shipped in tape and reel. Every reel is shipped from a single intensity and color bin except red color for better uniformity. * JEDEC MSL 3 * LED package with diffused silicone encapsulation * Using AlInGaP and InGaN dice technologies * Typical viewing angle at 115 * Compatible with reflow soldering process Applications * Indoor full color display CAUTION: LEDs are ESD-sensitive. Please observe appropriate precautions during handling and processing. Refer to Avago Application Note AN-1142 for additional details. Package Dimensions 1.9 2.8 2 3 2.2 0.8 0.7 0.86 3.2 3.5 2.4 Package Marking 1 4 0.7 2 3 1 4 Lead Configuration 1 Common Anode 2 Cathode (Blue) 3 Cathode (Green) 4 Cathode (Red) Notes: 1. All dimensions are in millimeters (mm). 2. Unless otherwise specified, tolerance = 0.20 mm. 3. Encapsulation = silicone 4. Terminal Finish: Silver plating 2 0.8 Table 1. Absolute Maximum Ratings (TJ = 25 C) Parameter Red Green/Blue Unit 25 25 mA 100 100 mA 90 mW DC Forward Current [1] Peak Forward Current [2] Power dissipation 65 Reverse Voltage Not recommended for reverse bias 110 C Operating Temperature Range -40 to 100 C Storage Temperature Range -40 to 100 C Junction Temperature Notes: 1. Derate linearly as shown in Figure 7 to Figure 10. 2. Duty factor = 10% frequency = 1 kHz. Table 2. Optical Characteristics (TJ = 25 C) Luminous Intensity, IV (mcd) @ IF = 20 mA [1] Dominant Wavelength, ld (nm) @ IF = 20 mA [2] Peak Wavelength, lP (nm) @ IF = 20 mA Viewing Angle, 2q1/2 () [3] Color Min. Typ. Max. Min. Typ. Max. Typ. Typ. Red 450 540 900 619.0 625.0 629.0 634.0 115 Green 1125 1600 2240 525.0 530.0 535.0 522.0 115 Blue 285 350 560 465.0 470.0 473.0 465.0 115 Notes: 1. Luminous intensity, IV is measured at the mechanical axis of the LED package at a single current pulse condition. The actual peak of the spatial radiation pattern may not be aligned with the axis. 2. Dominant wavelength is derived from the CIE Chromaticity Diagram and represents the perceived color of the device. 3. q1/2 is the off-axis angle where the luminous intensity is 1/2 of the peak intensity. Table 3. Electrical Characteristics (TJ = 25 C) Color Forward Voltage, VF (V) @ IF = 20 mA [1] Reverse Voltage, VR (V) @ IR = 100 A [2] Reverse Voltage, VR (V) @ IR = 10 A [2] Thermal Resistance, RqJ-S (C/W) Min. Typ. Max. Min. Min. Single chip on Three chips on Red 1.8 2.1 2.6 4.0 - 609 653 Green 2.8 3.1 3.6 - 4.0 320 430 Blue 2.8 3.1 3.6 - 4.0 320 430 Notes: 1. Tolerance = 0.1 V. 2. Indicates product final testing condition. Long-term reverse bias is not recommended. 3 Part Numbering System A S M B - M T B 0 - x1 Code Description 0 A 3 A 2 x2 x3 x4 x5 Option x1 x2 Package type Minimum intensity bin B A x3 x4 Number of intensity bins Color bin combination 3 A x5 Test option 2 Black surface Red: bin U1 Green: bin W1 Blue: bin T1 3 intensity bins from minimum Red: full distribution Green: bin A, B, D Blue: bin A, B, C Test current = 20 mA Note: MTB0 is Marveled V2 Red: bin U1, U2, V1 Green: bin W1, W2, X1 Blue: bin T1, T2, U1 Table 4. Bin Information Intensity Bins (CAT) Color Bins (BIN) - Green Bin ID Luminous intensity (mcd) Min. Max. T1 285.0 355.0 T2 355.0 450.0 Bin ID Dominant Wavelength (nm) Min. Max. Chromaticity Coordinate (for reference) Cx Cy A 525.0 0.1142 0.8262 0.7178 531.0 U1 450.0 560.0 0.1624 U2 560.0 715.0 0.2001 0.6983 V1 715.0 900.0 0.1625 0.8012 0.1387 0.8148 B 528.0 534.0 V2 900.0 1125.0 W1 1125.0 1400.0 0.1815 0.7089 0.2179 0.6870 0.1854 0.7867 0.1625 0.8012 0.2001 0.6983 0.2238 0.6830 0.1929 0.7816 W2 1400.0 1800.0 X1 1800.0 2240.0 D Tolerance: 12% 531.0 535.0 Color Bins (BIN) - Blue Bin ID Dominant Wavelength (nm) Min. Max. Chromaticity coordinate (for reference) Cx Cy A 465.0 0.1355 0.0399 0.1751 0.0986 0.1680 0.1094 0.1267 0.0534 0.1314 0.0459 0.1718 0.1034 0.1638 0.1167 0.1215 0.0626 B C 467.0 469.0 Tolerance: 1 nm 4 469.0 471.0 473.0 0.1267 0.0534 0.1680 0.1094 0.1593 0.1255 0.1158 0.0736 Tolerance: 1 nm Color Bins (BIN) - Red Bin ID Dominant Wavelength (nm) Min. Max. Chromaticity Coordinate (for reference) Cx Cy -- 619.0 0.6894 0.3104 0.6752 0.3113 0.6916 0.2950 0.7066 0.2934 Tolerance: 1 nm 629.0 Characteristics 100 1.0 Green FORWARD CURRENT (mA) Blue 0.6 0.4 0.2 450 500 550 600 WAVELENGTH (nm) 650 Figure 1. Relative Intensity vs. Wavelength 1.6 NORMALIZED INTENSITY 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 5 10 15 FORWARD CURRENT (mA) 20 25 Figure 3. Relative Luminous Intensity vs. Forward Current NORMALZIED INTENSITY 10 60 40 20 0 0 1 2 3 FORWARD VOLTAGE (V) 4 5 Figure 2. Forward Current vs. Forward Voltage Red Green Blue 1.4 RED GREEN/BLUE 80 700 RELATIVE DOMINANT WAVELENGTH SHIFT (nm) 0.0 400 7 Red Green Blue 6 5 4 3 2 1 0 -1 -2 0 5 10 15 FORWARD CURRENT (mA) 20 25 Figure 4. Dominant Wavelength Shift vs. Forward Current RED GREEN BLUE 1 0.5 FORWARD VOLTAGE SHIFT (V) NORMALIZED INTENSITY 0.8 Red RED GREEN BLUE 0.4 0.3 0.2 0.1 0 -0.1 -0.2 0.1 -40 -20 0 20 40 60 80 TJ -JUNCTION TEMPERATURE (C) Figure 5. Relative Luminous Flux vs. Junction Temperature 5 100 120 -0.3 -40 -20 0 20 40 60 80 TJ -JUNCTION TEMPERATURE (C) Figure 6. Forward Voltage Shift vs. Junction Temperature 100 120 30 MAXIMUM FORWARD CURRENT (mA) MAXIMUM FORWARD CURRENT (mA) 30 TS 20 TA 10 0 0 20 40 60 80 TEMPERATURE (C) 100 10 0 20 40 60 80 TEMPERATURE (C) TS 20 TA 10 0 20 40 60 TEMPERATURE (C) 80 100 Figure 9. Maximum Forward Current vs. Temperature for Green & Blue (1 Chip On) 120 TS 20 TA 10 0 0 20 40 60 TEMPERATURE (C) Condition Thermal resistance from LED junction to ambient, RJ-A (C/W) Red Green & Blue 1 chip on 725 454 3 chips on 970 747 80 100 Figure 10. Maximum Forward Current vs. Temperature for Green & Blue (3 Chips On) Note: Maximum forward current graphs based on ambient temperature, TA are with reference to thermal resistance RJ-A (see below). For more details, see Precautionary Notes, item 4. 6 100 30 MAXIMUM FORWARD CURRENT (mA) MAXIMUM FORWARD CURRENT (mA) TA Figure 8. Maximum Forward Current vs. Temperature For Red (3 Chips On) 30 0 20 0 120 Figure 7. Maximum Forward Current vs. Temperature For Red (1 Chip On) TS 1.0 0.80 0.8 0.60 NORMALIZED INTENSITY NORMALIZED INTENSITY 1.00 RED GREEN BLUE 0.40 0.20 0.00 -90 -60 -30 0 30 ANGULAR DISPLACEMENT (DEGREE) Figure 11a. Radiation pattern along x-axis of the package Figure 11c. Illustration of package axis for radiation pattern 7 60 90 0.6 0.4 RED GREEN BLUE 0.2 0.0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT (DEGREE) Figure 11b. Radiation pattern along y-axis of the package 60 90 2.6 1.1 4.5 1.5 Copper pad Maximize the size of copper pad of PIN 1 for better heat dissipation. Solder mask 2 0.05 PACKAGE MARKING 3.81 0.1 3.50 0.05 4 0.1 3.05 0.1 Figure 13. Carrier Tape Dimension 8 +0.2 1.0 0 USER FEED DIRECTION 2.14 0.1 +0.3 8.0 +0.1 4 0.1 +0.1 1.5 0 1.75 0.1 Figure 12. Recommended soldering land pattern 0.23 0.05 USER FEED DIRECTION PACKAGE MARKING PRINTED LABEL Figure 14. Reel Orientation 8.0 1.0 (0.315 0.039) 10.50 1.0 (0.413 0.039) 13.1 0.5 O (0.516 0.020) 20.20 MIN. O (0.795 MIN.) 3.0 0.5 (0.118 0.020) 59.60 1.00 (2.346 0.039) 178.40 1.00 (7.024 0.039) 4.0 0.5 (0.157 0.020) Figure 15. Reel Dimension 9 6 PS 5.0 0.5 (0.197 0.020) Packing Label (i) Standard label (attached on moisture barrier bag) (1P) Item: Part Number STANDARD LABEL LS0002 RoHS Compliant Halogen Free e4 Max Temp 260C MSL3 (1T) Lot: Lot Number (Q) QTY: Quantity LPN: CAT: Intensity Bin (9D)MFG Date: Manufacturing Date BIN: Color Bin (P) Customer Item: (9D) Date Code: Date Code (V) Vendor ID: DeptID: Made In: Country of Origin (ii) Baby label (attached on plastic reel) (1P) PART #: Part Number BABY LABEL COSB001B V0.0 (1T) LOT #: Lot Number (9D)MFG DATE: Manufacturing Date QUANTITY: Packing Quantity C/O: Country of Origin (9D): DATE CODE: (1T) TAPE DATE: D/C: Date Code CAT: U1 W1 VF: T1 CAT: INTENSITY BIN BIN: COLOR BIN Intensity for Blue: T1 Intensity for Green: W1 Example of luminous intensity (Iv) bin information on label: CAT: U1 W1 T1 Intensity for Red: U1 Example of color bin information on label: BIN: A B Intensity for Blue: T1 Intensity for Green: W1 Intensity for Red: U1 BIN: A B 10 Color Bin for Blue: B Color Bin for Blue: B Color Bin for Green: A Note: There is no color bin ID for Red as there is only one range, as stated in Table 4. Soldering Recommended reflow soldering condition: (i) Leaded reflow soldering: (ii) Lead-free reflow soldering: 20 SEC. MAX. 183C 100-150C -6C/SEC. MAX. 3C/SEC. MAX. 120 SEC. MAX. 60-150 SEC. TIME a. Reflow soldering must not be done more than two times. Make sure you take the necessary precautions for handling a moisture-sensitive device, as stated in the following section. b. Recommended board reflow direction: TEMPERATURE TEMPERATURE 10 to 30 SEC. 240C MAX. 3C/SEC. MAX. 217C 200C 255 - 260 C 3C/SEC. MAX. 6C/SEC. MAX. 150C 3 C/SEC. MAX. 100 SEC. MAX. 60 - 120 SEC. TIME c. Do not apply any pressure or force on the LED during reflow and after reflow when the LED is still hot. d. It is preferred that you use reflow soldering to solder the LED. Use hand soldering only for rework if unavoidable but must be strictly controlled to the following conditions: - Soldering iron tip temperature = 320 C max. - Soldering duration = 3 sec max. - Number of cycles = 1 only - Power of soldering iron = 50 W max. e. Do not touch the LED body with a hot soldering iron except the soldering terminals as this may damage the LED. f. For de-soldering, it is recommended that you use a double flat tip. g. Please confirm beforehand whether the functionality and performance of the LED is affected by hand soldering. REFLOW DIRECTION 11 PRECAUTIONARY NOTES 1. Handling precautions The encapsulation material of the LED is made of silicone for better product reliability. Compared to epoxy encapsulant, which is hard and brittle, silicone is softer and flexible. Observe special handling precautions during assembly of silicone-encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. For more information, refer to Application Note AN5288, Silicone Encapsulation for LED: Advantages and Handling Precautions. a. Do not poke sharp objects into the silicone encapsulant. Sharp objects such as tweezers and syringes might cause excessive force to be applied or even pierce through the silicone, inducing failures in the LED die or wire bond. b. Do not touch the silicone encapsulant. Uncontrolled force acting on the silicone encapsulant might result in excessive stress on the wire bond. The LED should be held only by the body. c. Do no stack assembled PCBs together. Use an appropriate rack to hold the PCBs. d. The surface of silicone material attracts more dust and dirt compared to epoxy due to its surface tackiness. To remove foreign particles on the surface of silicone, a cotton bud can be used with isopropyl alcohol (IPA). During cleaning, rub the surface gently without applying excessive pressure on the silicone. Ultrasonic cleaning is not recommended. e. For automated pick and place, Avago has tested the following nozzle size to work fine with this LED. However, due to possible variations in other parameters such as pick and place machine maker/model and other settings of the machine, it is recommended that you verify that the nozzle selected will not damage the LED. 2. Handling of moisture-sensitive device This product has a Moisture Sensitive Level 3 rating per JEDEC J-STD-020. Refer to Avago Application Note AN5305, Handling of Moisture Sensitive Surface Mount Devices, for additional details and a review of proper handling procedures. a. Before use - An unopened moisture barrier bag (MBB) can be stored at < 40 C/90% RH for 12 months. If the actual shelf life has exceeded 12 months and the Humidity Indicator Card (HIC) indicates that baking is not required, then it is safe to reflow the LEDs per the original MSL rating. - It is recommended that the MBB not be opened before assembly (e.g., for IQC). b. Control after opening the MBB - Read the HIC immediately upon opening the MBB. - The LEDs must be kept at < 30 C/60% RH at all times and all high temperature related processes including soldering, curing or rework must be completed within 168 hours. c. Control for unfinished reel - Unused LEDs must be stored in a sealed MBB with desiccant or desiccator at < 5% RH. d. Control of assembled boards - If the PCB soldered with the LEDs is to be subjected to other high temperature processes, then the PCB must be stored in a sealed MBB with desiccant or desiccator at < 5% RH to ensure that all LEDs have not exceeded their floor life of 168 hours. e. Baking is required if: - The HIC indicator is not BROWN at 10% and is AZURE at 5%. - The LEDs are exposed to a condition of > 30 C/60% RH at any time. - The LED floor life exceeded 168 hours. The recommended baking condition is: 60 5 C for 20 hours. Baking should be done only once. f. Storage ID OD ID = 1.7 mm OD = 3.5 mm 12 - The soldering terminals of these Avago LEDs are silver-plated. If the LEDs are exposed in ambient environment for too long, the silver plating might be oxidized and thus affect its solderability performance. As such, unused LEDs must be kept in a sealed MBB with desiccant or in desiccator at < 5% RH. 3. Application precautions a. Drive current of the LED must not exceed the maximum allowable limit across temperature as stated in the datasheet. Constant current driving is recommended to ensure consistent performance. The complication of using this formula lies in TA and RqJ-A. Actual TA is sometimes subjective and hard to determine. RqJ-A varies from system to system depending on design and is usually not known. b. The LED is not intended for reverse bias. Do use other appropriate components for such a purpose. When driving the LED in matrix form, make sure the reverse bias voltage does not exceed the allowable limit for the LED. Another way of calculating TJ is by using solder point temperature TS as shown as follows: c. Do not use the LED in the vicinity of material with sulfur content, in an environment of high gaseous sulfur compound and corrosive elements. Examples of materials that may contain sulfur are rubber gasket, Room Temperature Vulcanizing (RTV) silicone rubber, rubber gloves, and so on. Prolonged exposure to such an environment may affect the optical characteristics and product life. d. Avoid a rapid change in ambient temperature especially in a high humidity environment as this will cause condensation on the LED. 4. Thermal management Optical, electrical and reliability characteristics of LED are affected by temperature. The junction temperature (TJ ) of the LED must be kept below the allowable limit at all times. TJ can be calculated as follows: TJ = TA + RqJ-A x IF x VFmax where TA = ambient temperature [C] RqJ-A = thermal resistance from LED junction to ambient [C/W] IF = forward current [A] TJ = TS + RqJ-S x IF x VFmax where TS = LED solder point temperature as shown in the following illustration [C] RqJ-S = thermal resistance from junction to solder point [C/W] Ts point (PIN 1) TS can be easily measured by having a thermocouple mounted on the soldering joint, as shown in this illustration, while RqJ-S is provided in the datasheet. Please verify the TS of the LED in the final product to ensure that the LEDs are operated within all maximum ratings stated in the datasheet. 5. Eye safety precautions LEDs may pose optical hazards when in operation. It is not advisable to view directly at operating LEDs as it may be harmful to the eyes. For safety reasons, use appropriate shielding or personal protective equipment. VFmax = maximum forward voltage [V] DISCLAIMER: Avago's products and software are not specifically designed, manufactured or authorized for sale as parts, components or assemblies for the planning, construction, maintenenace or direct operation of a nuclear facility or for use in medical devices or applications. Customer is solely responsible, and waives all rights to make claims against Avago or its suppliers, for all loss, damage, expense or liability in connection with such use. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2014 Avago Technologies. All rights reserved. AV02-4186EN - September 10, 2014 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Avago Technologies: ASMB-MTB0-0A3A2