Phototriac Coupler (APT1) VDE Phototriac Coupler with various options for external Triac control Phototriac Coupler (APT1) FEATURES TYPICAL APPLICATIONS 1. Low zero-cross voltage (max. 15 V) type added to lineup. Approximately 1/3 of previous product Helps reduce device noises even further. 1. For triac driver in heater controls of products such as office equipment, home appliances, and industrial machines. (For 100V/200V, 50/60 Hz lines) 2. Triac driver for SSRs APT1 Previous product: max. 50 V Load voltage New product: max. 15 V High noise Low noise Large interfering wave 1 4 1 Small interfering wave 6 2 2 ZC Zero-cross circuit 3 1 4 2 3 3 ZC Zero-cross circuit 1 4 2. Two types available: Random type and zero-cross type 3. Many package sizes available. (Wide terminal type with 10.16 mm pitch between I/O terminals available.) 4. High dielectric strength. (Between input and output: SOP 3, 750 V; DIP 5,000 V) 5. Handles both 100 and 200 V AC loads This relay handles both voltages in a single product it is not necessary for users that use both types to manage separate part numbers. 6. Terminal 5 of the DIP 6-pin type is completely molded. 6 2 3 4 TYPES 1. SOP4 Type Type Output rating Repetitive peak ON-state RMS OFF-state voltage current Type Package size Zero-cross (max. 50 V) AC type 600 V 50 mA Zero-cross (max. 15 V) Random SOP4pin Part No. Tube packing style Packing quantity Tape and reel packing style APT1211S APT1211SX (Picked from the 1/2-pin side) APT1211SZ (Picked from the 3/4-pin side) APT1231S APT1231SX (Picked from the 1/2-pin side) APT1231SZ (Picked from the 3/4-pin side) APT1221S APT1221SX (Picked from the 1/2-pin side) APT1221SZ (Picked from the 3/4-pin side) Tube Tape and reel 1 tube contains: 100 pcs. 1 batch contains: 2, 000 pcs. 1, 000 pcs. Note: For space reasons, the initial letters of the product number "APT" and "S" are omitted on the product seal. The package type indicator "X" and "Z" are omitted from the seal. (Ex. the label for product number APT1221SZ is 1221). ds_61690_en_apt1: 010611D 1 Phototriac Coupler (APT1) 2. DIP4/6 Type Output rating Type Repetitive peak OFF-state voltage Part No. ON-state RMS current Type Package size APT1211 APT1211A APT1231 APT1231A Random APT1221 APT1221A Zero-cross (max. 50 V) APT1212 APT1212A APT1232 APT1232A APT1222 APT1222A Zero-cross (max. 15 V) 600 V Surface-mount terminal Tube packing style Zero-cross (max. 50 V) AC type Through hole terminal DIP4pin Tape and reel packing style 100 mA Zero-cross (max. 15 V) DIP6pin Random APT1211AX (Picked from the 1/2-pin side) APT1211AZ (Picked from the 3/4-pin side) APT1231AX (Picked from the 1/2-pin side) APT1221AX (Picked from the 1/2-pin side) APT1212AX (Picked from the 1/2/3-pin side) APT1231AZ (Picked from the 3/4-pin side) APT1232AX (Picked from the 1/2/3-pin side) APT1222AX (Picked from the 1/2/3-pin side) APT1232AZ (Picked from the 4/6-pin side) APT1222AZ (Picked from the 4/6-pin side) APT1221AZ (Picked from the 3/4-pin side) APT1212AZ (Picked from the 4/6-pin side) Packing quantity Tube Tape and reel [DIP4pin] 1 tube contains: 100 pcs. 1 batch contains: 1,000 pcs. [DIP6pin] 1 tube contains: 50 pcs. 1 batch contains: 500 pcs. [DIP4pin] [DIP6pin] 1,000 pcs. Note: For space reasons the initial letters "APT" of the product number for the DIP 4-pin type, the letter "A", which indicates the SMD terminal shape for the DIP 4-pin and 6-pin types, and the package type indications "X" and "Z" have been omitted from the product label. (Example: The label for product number APT1221AZ is 1221.) 3. DIP4/6 Wide Terminal Type Output rating* Type Repetitive peak OFF-state voltage Part No. ON-state RMS current Type Package size Zero-cross (max. 15 V) DIP4pin Random 600 V Surface-mount terminal Tube packing style Zero-cross (max. 50 V) AC type Through hole terminal APT1211W APT1211WA APT1231W APT1231WA APT1231WAY (Picked from the 1/4-pin side) APT1231WAW (Picked from the 2/3-pin side) APT1221W APT1221WA APT1221WAY (Picked from the 1/4-pin side) APT1221WAW (Picked from the 2/3-pin side) APT1212W APT1212WA APT1212WAY (Picked from the 1/6-pin side) APT1212WAW (Picked from the 3/4-pin side) APT1232W APT1232WA APT1232WAY (Picked from the 1/6-pin side) APT1232WAW (Picked from the 3/4-pin side) APT1222W APT1222WA APT1222WAY (Picked from the 1/6-pin side) APT1222WAW (Picked from the 3/4-pin side) 100 mA Zero-cross (max. 50 V) Zero-cross (max. 15 V) Random DIP6pin Tape and reel packing style APT1211WAY (Picked from the 1/4-pin side) APT1211WAW (Picked from the 2/3-pin side) Packing quantity Tube Tape and reel [DIP4pin] 1 tube contains: 100 pcs. 1 batch contains: 1,000 pcs. [DIP6pin] 1 tube contains: 50 pcs. 1 batch contains: 500 pcs. [DIP4pin] [DIP6pin] 1,000 pcs. Note: For space reasons the initial letters "APT" of the product number for the DIP 4-pin type, the letter "WA", which indicates the SMD terminal shape for the DIP 4-pin and 6-pin types, and the package type indications "Y" and "W" have been omitted from the product label. (Example: The label for product number APT1221WAY is 1221.) RATING 1. Absolute maximum ratings (Ambient temperature: 25C 77F) 1) SOP4 types Input Output Item LED forward current LED reverse voltage Symbol IF VR APT1211S, APT1221S, APT1231S 50 mA 6V Peak forward current IFP 1A VDRM 600 V IT(RMS) 0.05 A AC ITSM 0.6 A In one cycle at 60Hz PT Viso 350 mW 3,750 V AC Operating Topr -40C to +100C -40F to +212F Storage Tstg -40C to +125C -40F to +257F Repetitive peak OFF-state voltage ON-state RMS current* Non-repetitive surge current Total power dissipation I/O isolation voltage Temperature limits Remarks f = 100 Hz, Duty Ratio = 0.1% Non-condensing at low temperatures Note: "X" and "Z" at the end of the part numbers have been omitted. 2 ds_61690_en_apt1: 010611D Phototriac Coupler (APT1) 2) DIP4/6 type and DIP4/6 Wide terminal type Item LED forward current LED reverse voltage Symbol IF VR Peak forward current IFP 1A VDRM 600 V IT(RMS) 0.1 A AC ITSM 1.2 A In one cycle at 60Hz Total power dissipation PT I/O isolation voltage Viso 500 mW 5,000 V AC Operating Topr -40C to +100C -40F to +212F Storage Tstg -40C to +125C -40F to +257F Input Output Repetitive peak OFF-state voltage ON-state RMS current* Non-repetitive surge current Temperature limits APT1211(W) APT1221(W) APT1231(W) APT1212(W) 50 mA 6V APT1222(W) APT1232(W) Remarks f = 100 Hz, Duty Ratio = 0.1% Non-condensing at low temperatures Note: "A", "AX", "AZ" "AY" and "AW" at the end of the part numbers have been omitted. * Do not exceed 0.05 A of ON state RMS current in case of following load voltage condition. DIP4pin (APT1211, APT1221, APT1231) and DIP4pin wide terminal type (APT1211W, APT1221W, APT1231W): more than 100 V AC; DIP6pin (APT1212, APT1222, APT1232) and DIP6pin wide terminal type (APT1212W, APT1222W, APT1232W): more than 120 V AC. 2. Electrical characteristics (Ambient temperature: 25C 77F) 1) Zero-cross voltage type (max. 50V) and random type Item LED dropout voltage Input LED reverse current Repetitive peak OFF-state current Output Repetitive peak On-state voltage Holding current Critical rate of rise of OFF-state voltage Symbol Typical Maximum Typical Maximum Typical Maximum Typical Maximum Typical Maximum Minimum VF APT1211S, APT1211(W), APT1212(W) APT1221S, APT1221(W), APT1222(W) 1.21 V 1.3 V -- IR IH dv/dt VDRM = 600 V 1/2 500 V/s 10 mA Maximum IFT Zero-cross voltage Maximum VZC Maximum Ton 100 s I/O capacitance Maximum Ciso 1.5 pF I/O resistance Minimum Riso 50 G Notes: 1. For type of connection, see page 8. 2. Terminals are either solder plated or solder dipped. IF = 10 mA ITM = 0.05 A 2.5 V 0.3 mA 3.5 mA Trigger LED current Transfer Turn on time* characteristics IF = 0 mA VDRM = 600 V 1 A 1.3 V VTM IF = 20 mA VR = 6 V 10 A -- IDRM Condition 50 V -- VD = 6 V RL = 100 IF = 10 mA IF = 20 mA VD = 6 V RL = 100 f = 1 MHz VB = 0 V 500 V DC *Turn on time Input 90% Output Ton ds_61690_en_apt1: 010611D 3 Phototriac Coupler (APT1) 2) Zero-cross voltage type (max. 15V) Item Symbol Typical LED dropout voltage Maximum Typical Maximum Typical Input LED reverse current Repetitive peak OFF-state current Maximum Typical Maximum Typical Maximum Repetitive peak On-state voltage Output Holding current APT1231S, APT1231(W), APT1232(W) 1.21 V VF IR VR = 6 V 10 A -- IDRM IF = 0 mA VDRM = 600 V 1 A 1.2 V VTM IF = 10 mA ITM = 0.03 A 2V 0.3 mA 3.5 mA IH Minimum dv/dt 500 V/s Trigger LED current Zero-cross voltage Maximum Maximum IFT VZC 10 mA 15 V Maximum Ton 100 s Maximum Ciso 1.5 pF Minimum Riso 50 G I/O resistance IF = 20 mA 1.3 V -- Critical rate of rise of OFF-state voltage Turn on time* Transfer characteristics I/O capacitance Condition Notes: 1. For type of connection, see page 8. 2. Terminals are either solder plated or solder dipped. VDRM = 600 V 1/2 IDRM = 30 mA IF = 10 mA IF = 20 mA IDRM = 30 mA f = 1 MHz VB = 0 V 500 V DC *Turn on time Input 90% Output Ton RECOMMENDED OPERATING CONDITIONS Please follow the conditions below in order to ensure accurate operation and release of the phototriac coupler. Item Input LED current Symbol IF Value 20 Unit mA REFERENCE DATA 1-(1). ON-state RMS current vs. ambient temperature characteristics 1-(2). ON-state RMS current vs. ambient temperature characteristics 1-(3). ON-state RMS current vs. ambient temperature characteristics Allowable ambient temperature: -40C to +100C -40F to +212F Tested sample: APT1211S, APT1221S Allowable ambient temperature: -40C to +100C -40F to +212F Tested sample: APT1231S Allowable ambient temperature: -40C to +100C -40F to +212F Tested sample: APT1211(A), APT1221(A), APT1211W(A), APT1221W(A) 70 60 50 40 30 20 10 0 -40 60 50 40 30 20 -20 0 20 40 60 80 100 0 -40 100 VL 100V AC 80 60 VL > 100V AC 40 20 10 Ambient temperature, C 4 120 ON-state RMS current, mA ON-state RMS current, mA ON-state RMS current, mA 70 -20 0 20 40 60 80 Ambient temperature, C 100 0 -40 -20 0 20 40 60 80 100 Ambient temperature, C ds_61690_en_apt1: 010611D Phototriac Coupler (APT1) 1-(4). ON-state RMS current vs. ambient temperature characteristics 1-(5). ON-state RMS current vs. ambient temperature characteristics 1-(6). ON-state RMS current vs. ambient temperature characteristics Allowable ambient temperature: -40C to +100C -40F to +212F Tested sample: APT1231(A), APT1231W(A) Allowable ambient temperature: -40C to +100C -40F to +212F Tested sample: APT1212(A), APT1222(A), APT1212W(A), APT1222W(A) Allowable ambient temperature: -40C to +100C -40F to +212F Tested sample: APT1232(A), APT1232W(A) 120 100V AC 80 60 VL > 100V AC 40 20 100 120 VL 120V AC 80 60 VL > 120V AC 40 -20 0 20 40 60 80 0 -40 100 100 VL 120V AC 80 60 VL > 120V AC 40 20 20 0 -40 -20 0 Ambient temperature, C 20 40 60 80 0 -40 100 -20 0 3. Trigger LED current vs. ambient temperature characteristics 1.8 60 80 8 6 4 1.4 1.3 50mA 1.2 30mA 20mA 1.2 -20 0 20 40 60 80 0 -40 100 -20 0 Ambient temperature, C 30 20 10 20 60 80 30 40 1 100 -40 -20 50 LED current, mA 20 40 60 80 100 7. Hold current vs. ambient temperature characteristics 0.001 2 105 107 109 1.5 1 0.5 1011 1013 0 0 Ambient temperature, C Hold current, mA Repetitive peak OFF-state current, A 40 10 40 6. Repetitive peak OFF-state current vs. Load voltage characteristics 50 0 20 Ambient temperature, C 5. Turn on time vs. LED current 0 10mA 1.1 2 0 -40 100 1.5 LED dropout voltage, V Trigger LED current, mA 1.4 40 4. LED dropout voltage vs. ambient temperature characteristics 10 1.6 20 Ambient temperature, C Ambient temperature, C 2. On voltage vs. ambient temperature characteristics On voltage, V ON-state RMS current, mA VL 100 ON-state RMS current, mA ON-state RMS current, mA 120 20 40 60 80 Load voltage, V 100 0 -40 -20 0 20 40 60 80 100 Ambient temperature, C 8. Zero-cross voltage vs. ambient temperature characteristics Zero-cross voltage, V 50 40 30 20 10 0 -40 -20 0 20 40 60 80 100 Ambient temperature, C ds_61690_en_apt1: 010611D 5 Phototriac Coupler (APT1) DIMENSIONS (mm inch) CAD Data Data from our Web site. Download CAD 1. SOP Type APT1211S, APT1221S, APT1231S Recommended mounting pad (TOP VIEW) CAD Data 0.5 .020 4.40.2 .173009 4.30.2 .169.009 0.4 .016 2.54 .100 0.8 .032 2.54 .100 0.5 .020 2.00.2 .079.009 0.4 .016 6.0 1.2 .236 .047 6.80.4 .268016 Tolerance: 0.1 .004 0.1 .004 Terminal thickness = 0.15 .006 General tolerance: 0.1 .004 2. DIP4 Type APT1211(A), APT1221(A), APT1231(A) CAD Data Through hole terminal type Surface mount terminal type Max. 10 Max. 10 6.4 .252 7.620.05 .300.002 6.4 .252 7.620.05 .300.002 Max. 10 4.78 .188 3.20.2 .126.008 2.7 .106 3.0 .118 0.2 .008 0.33 .013 0.47 .019 1.0 .039 0.47 .019 2.70.05 .106.002 0.2 0.2 0 .008 .008 0 0.47 .019 1.0 .039 2.54 .100 1.0 .039 4.78 .188 2.70.05 .106.002 0.47 .019 2.54 .100 1.0 .039 Terminal thickness = 0.2 .008 General tolerance: 0.1 .004 PC board pattern (BOTTOM VIEW) 4-0.8 dia. 4-.031 dia. Recommended mounting pad (TOP VIEW) 2.54 .100 8.3 .327 6.4 .252 7.62 .300 2.54 .100 Tolerance: 0.1 .004 6 1.9 .075 1.5 .059 2.54 .100 Tolerance: 0.1 .004 ds_61690_en_apt1: 010611D Phototriac Coupler (APT1) 3. DIP4 Wide Terminal Type APT1211W(A), APT1221W(A), APT1231W(A) Through hole terminal type CAD Data Surface mount terminal type Max. 10 Max. 10 0.05 0.5 10.16 .400.020 6.4 .252.002 Max. 10 2.70.05 .106.002 4.78 0.05 1.88 .002 2.70.05 .106.002 4.780.05 .188.002 0.75 .030 0.20.2 .008.008 0.2 .008 0.33 .013 3.0 .118 Max. 12.0 10.160.5 Max. .472 .400.020 6.4 0.05 .252.002 2.54 .100 0.47 .019 0.47 .019 1.0 .039 Terminal thickness = 0.20 .008 General tolerance: 0.1 .004 2.54 .100 PC board pattern (BOTTOM VIEW) 4-0.8 dia. 4-.031 dia. Recommended mounting pad (TOP VIEW) 2.54 .100 10.8 .425 6.4 .252 1.9 .075 10.16 .400 1.5 .059 2.54 .100 2.54 .100 Tolerance: 0.1 .004 Tolerance: 0.1 .004 4. DIP6 Type APT1212(A), APT1222(A), APT1232(A) Through hole terminal type CAD Data Surface mount terminal type Max. 10 Max. 10 6.40.05 .252.002 7.620.05 .300.002 6.40.05 .252.002 7.6 .299 Max. 10 8.80.05 .346.002 3.4 .134 3.90.2 .154.008 3.4 .134 0.2 .008 0.47 .019 3.0 .118 0.47 .019 1.25 .049 2.54 .100 1.25 .049 0.47 .019 0.47 .019 1.25 .049 6.4 .252 0.47 .019 0.47 .019 1.25 .049 2.54 .100 1.25 .049 Terminal thickness = 0.25 .010 General tolerance: 0.1 .004 5.08 .200 2.54 .100 Recommended mounting pad (TOP VIEW) 8.3 .327 7.62 2.54 .300 .100 1.9 .075 1.5 .059 Tolerance: 0.1 .004 ds_61690_en_apt1: 010611D 3.4 .134 1.25 .049 2.54 2.54 .100 .100 PC board pattern (BOTTOM VIEW) 6-0.8 dia. 6-.031 dia. 1 .039 8.80.05 .346.002 2.54 2.54 .100 .100 Tolerance: 0.1 .004 7 Phototriac Coupler (APT1) 5. DIP6 Wide Terminal Type APT1212W(A), APT1222W(A), APT1232W(A) Through hole terminal type CAD Data Surface mount terminal type Max. 10 MAX. 10 6.40.05 .252.002 10.160.5 .400.020 MAX. 10 6.40.05 .252.002 Max. 12.0 10.160.5 Max. .472 .400.020 0.75 .030 3.4 .134 8.80.05 .346.002 3.4 .134 8.80.05 .346.002 3.0 .118 3.4 .134 0.47 0.47 0.47 .019 .019 .019 1.25 1.25 .049 1.25 .049 .049 2.54 2.54 .100 .100 0.20.2 .008.008 0.47 .019 1.25 .049 0.47 .019 0.47 .019 1.25 .049 1.25 .049 2.54 2.54 .100 .100 Terminal thickness = 0.25 .010 General tolerance: 0.1 .004 PC board pattern (BOTTOM VIEW) 5-0.8 dia. 5-.031 dia. Recommended mounting pad (TOP VIEW) 5.08 .200 2.54 .100 10.8 .425 6.4 .252 10.16 .400 2.54 .100 1.9 .075 1.5 .059 2.54 2.54 .100 .100 Tolerance: 0.1 .004 Tolerance: 0.1 .004 SCHEMATIC AND WIRING DIAGRAMS Notes: E1: Power source at input side; IF: LED forward current; VL: Load voltage; IL: Load current; Output configuration Schematic 1 2 Load Wiring diagram 4 ZC Zero-cross circuit 3 1 4 2 3 4 Load E1 IF 1 4 2 3 VL (AC) 3 Load 1 Form A 1 VL (AC) AC 6 2 3 ZC Zero-cross circuit 4 1 E1 IF 6 6 2 VL (AC) 3 1 6 Load 4 VL (AC) 4 Load 2 3 4 See special section on Phototriac Couplers in Cautions for Use 8 ds_61690_en_apt1: 010611D