K3HB-PPB 100-240VAC - Omron Automation and Safety

CSM_K3HB-P_DS_E_15_1

Timer Interval Indicator

K3HB-P

Digital Time Interval Meter for Measuring

Passing Speed, Time, or Cycle between Two

Points.

• Visual confirmation of judgement results through display colors that

switch between red and green. *1

• Measures Wide Range of Pulse Interval Times

Measures, calculates, and displays pulse intervals between two points. Wide

range for pulse interval measurements, from 10 ms to 3,200 s, max.

• Six Measurement Operations, Including Passing Speed, Time, and

Cycle Measurement between Two Points

One Digital Time Interval Meter has six measurement functions, to support a

variety of pulse interval measurement applications. Select the best function

for your application from the following: Passing speed, cycle, time difference,

time band, measuring length, and interval.

• DeviceNet models added to the series. *2

Visual confirmation of judgement results is not supported on models that do not have an

output or models that do not support DeviceNet.

You can change the display color by setting it, but you cannot switch it based on the judgement results.

DeviceNet models have a depth of 97 mm.

Model Number Structure

■Model Number Legend

Base Units and Optional Boards can be ordered individually or as sets.

Note: The following combinations are not possible.

• Communications (FLK@A) + DeviceNet (DRT)

• Communications (FLK@A) + BCD output (BCD)

• Linear current/voltage (L@A) + DeviceNet (DRT)

Refer to Safety Precautions for All Digital Panel

Meters.

Base Units

1. Input Sensor Code

NB: NPN input/voltage pulse input

PB: PNP input

5. Supply Voltage

100-240 VAC: 100 to 240 VAC

24 VAC/VDC: 24 VAC/VDC

Optional Board

Sensor Power Supply/Output Boards

Relay/Transistor Output Boards

Event Input Boards

Base Units with Optional Boards

2. Sensor Power Supply/Output Type Code

None: None

CPA: Relay output (PASS: SPDT) + Sensor power supply

(12 VDC±10%, 80 mA) (See note 1.)

L1A: Linear current output (0 to 20 or 4 to 20 mA DC) + Sensor power supply

(12 VDC±10%, 80 mA) (See note 2.)

L2A: Linear voltage output (0 to 5, 1 to 5, or 0 to 10 VDC) + Sensor power supply

(12 VDC±10%, 80 mA) (See note 2.)

A: Sensor power supply (12 VDC ±10%, 80 mA)

FLK1A: Communications (RS-232C) + Sensor power supply

(12 VDC±10%, 80 mA) (See note 2.)

FLK3A: Communications (RS-485) + Sensor power supply

(12 VDC±10%, 80 mA) (See note 2.)

Note: 1. CPA can be combined with relay outputs only.

2. Only one of the following can be used by each Digital Indicator: RS-232C/RS-

485 communications, a linear output, or DeviceNet communications.

3. Relay/Transistor Output Type Code

None: None

C1: Relay contact (H/L: SPDT each)

C2: Relay contact (HH/H/LL/L: SPST-NO each)

T1: Transistor (NPN open collector: HH/H/PASS/L/LL)

T2: Transistor (PNP open collector: HH/H/PASS/L/LL)

BCD∗: BCD output + transistor output (NPN open collector: HH/H/PASS/L/LL)

DRT: DeviceNet (See note 2.)

∗ A Special BCD Output Cable (sold separately) is required.

4. Event Input Type Code

None: None

1: 5 inputs (HOLD/RESET), NPN open collector

2: 8 inputs (HOLD/RESET/BANK1/BANK2/BANK4), NPN open collector

3: 5 inputs (HOLD/RESET), PNP open collector

4: 8 inputs (HOLD/RESET/BANK1/BANK2/BANK4), PNP open collector

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

K3HB-P @

K33-@

K34-@

K35-@

1 234 5

K3HB-P@-@@@

K3HB-P

Accessories (Sold Separately)

K32-DICN: Special Cable (for event inputs with 8-pin connector)

K32-BCD: Special BCD Output Cable

Watertight Cover Rubber Packing

Note: Rubber packing is provided with the Controller.

Specifications

■Ratings

Note: 1. DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON. Particular

attention is required when using two or more DC power supply models. The OMRON S8VS-series DC Power Supply Unit is

recommended.

2. PNP input types are also available.

3. For K3HB-series DeviceNet models, use only the DeviceNet Connector included with the product. The crimp terminals provided are for

Thin Cables.

Model

Y92A-49N

Model

K32-P1

Supply voltage 100 to 240 VAC, 24 VAC/VDC, DeviceNet power supply: 24 VDC

Allowable power supply voltage

range

85% to 110% of the rated power supply voltage, DeviceNet power supply: 11 to 25 VDC

Power consumption

(See note 1.)

100 to 240 VAC: 18 VA max. (max. load)

24 VAC/DC: 11 VA/7 W max. (max. load)

Current consumption DeviceNet power supply: 50 mA max. (24 VDC)

Input No-voltage contact, voltage pulse, open collector

External power supply 12 VDC 10%, 80 mA (for models with external power supplies only)

Event inputs

(See note 2.)

Hold input NPN open collector or no-voltage contact signal

ON residual voltage: 2 V max.

ON current at 0 Ω: 4 mA max.

Max. applied voltage: 30 VDC max.

OFF leakage current: 0.1 mA max.

Reset input

Bank input

Output ratings

(depends on

the model)

Relay output 250 VAC, 30 VDC, 5 A (resistive load)

Mechanical life expectancy: 5,000,000 operations, Electrical life expectancy: 100,000 operations

Transistor output Maximum load voltage: 24 VDC, Maximum load current: 50 mA, Leakage current: 100 μA max.

Linear output Linear output 0 to 20 mA DC, 4 to 20 mA DC:

Load: 500 Ω max, Resolution: Approx. 10,000, Output error: ±0.5% FS

Linear output 0 to 5 VDC, 1 to 5 VDC, 0 to 10 VDC:

Load: 5 kΩ max, Resolution: Approx. 10,000, Output error: ±0.5% FS

(1 V or less: ±0.15 V; no output for 0 V or less)

Display method Negative LCD (backlit LED) display

7-segment digital display (Character height: PV: 14.2 mm (green/red); SV: 4.9 mm (green))

Main functions Scaling function, measurement operation selection, output hysteresis, output OFF delay, output test, teaching, dis-

play value selection, display color selection, key protection, bank selection, display refresh period, maximum/mini-

mum hold, reset

Ambient operating temperature −10 to 55°C (with no icing or condensation)

Ambient operating humidity 25% to 85%

Storage temperature −25 to 65°C (with no icing or condensation)

Altitude 2,000 m max.

Accessories Watertight packing, 2 fixtures, terminal cover, unit stickers, instruction manual. DeviceNet models also include a De-

viceNet connector (Hirose HR31-5.08P-5SC(01)) and crimp terminals (Hirose HR31-SC-121) (See note 3.)

K3HB-P

■Characteristics

Display range −19,999 to 99,999

Measurement accuracy

(at 23±5°C)

±0.08% rgd ±1 digit (for voltage pulse/open collector sensors)

Measurement range Functions F1, F3, and F4:(Interval between input pulses) 10 ms to 3,200 s

Function F2: (Interval between input pulses) 20 ms to 3,200 s

Functions F5, F6: (Number of input pulses) 0 to 4 gigacounts

Input signals • Contact input (dry contact input) (30 Hz max. with ON/OFF pulse width of 15 ms min.)

•No contact

voltage pulse

•Open collector

Connectable sensors ON residual voltage: 3 V max.

OFF leakage current: 1.5 mA max.

Load current: Must have a switching capacity of 20 mA or higher.

Must be able to properly switch load currents of 5 mA or less.

Comparative output response

time (transistor output)

2 ms max. (time until the comparative output is made when there is a forced sudden change in the input signal

from 15% to 95% or 95% to 15%)

Linear output response time 10 ms max. (time until the final analog output value is reached when there is a forced sudden change in the

input signal from 15% to 95% or 95% to 15%)

Insulation resistance 20 MΩ min. (at 500 VDC)

Dielectric strength 2,300 VAC for 1 min between external terminals and case

Noise immunity 100 to 240 VAC models:

±1,500 V at power supply terminals in normal or common mode

(waveform with 1-ns rising edge and pulse width of 1 μs/100 ns)

24 VAC/VDC models:

±1,500 V at power supply terminals in normal or common mode

(waveform with 1-ns rising edge and pulse width of 1 μs/100 ns)

Vibration resistance Frequency: 10 to 55 Hz; Acceleration: 50 m/s2, 10 sweeps of 5 min each in X, Y, and Z directions

Shock resistance 150 m/s2 (100 m/s2 for relay outputs) 3 times each in 3 axes, 6 directions

Weight Approx. 300 g (Base Unit only)

Degree of

protection

Front panel Conforms to NEMA 4X for indoor use (equivalent to IP66)

Rear case IP20

Terminals IP00 + finger protection (VDE0106/100)

Memory protection EEPROM (non-volatile memory)

Number of rewrites: 100,000

Applicable standards UL61010-1, CSA C22.2 No. 61010-1-04

EN61010-1 (IEC61010-1): Pollution degree 2/Overvoltage category II

EN61326-1

EMC EMI: EN61326 industrial applications

Electromagnetic radiation interference

CISPR 11 Group 1, Class A

Terminal interference voltage

CISPR 11 Group 1, Class A

EMS: EN61326 industrial applications

Electrostatic Discharge Immunity

EN61000-4-2: 4 kV (contact), 8 kV (in air)

Radiated Electromagnetic Field Immunity

EN61000-4-3: 10 V/m sine wave amplitude modulation (80 MHz to 1 GHz, 1.4GHz to 2 GHz)

Electrical Fast Transient/Burst Noise Immunity

EN61000-4-4: 2 kV (power line), 1 kV (I/O signal line)

Surge Immunity

EN61000-4-5: 1 kV with line (power line), 2 kV with ground (power line)

Conducted Disturbance Immunity

EN61000-4-6: 3 V (0.15 to 80 MHz)

Power Frequency Magnetic Immunity

EN61000-4-8: 30 A/m (50 Hz) continuous time

Voltage Dips and Interruptions Immunity

EN61000-4-11: 0.5 cycle, 0°/180°, 100% (rated voltage)

Mode Input frequency

range

ON/OFF

pulse width

ON voltage OFF voltage Input

impedance

F1 to F4 0 to 50 kHz 9 μs min. 4.5 to 30 V −30 to 2 V 10 kΩ

F5, F6 0 to 30 kHz 16 μs min.

Mode Input frequency

range

ON/OFF

pulse width

Note: The Digital Time Interval Meter

will malfunction if a pulse greater

than the input frequency range is

input. SYSERR may appear on

the display.

F1 to F4 0 to 50 kHz 9 μs min.

F5, F6 0 to 30 kHz 16 μs min.

K3HB-P

Operation

■Functions (Operating Modes)

F1 to F6

These functions use the internal system clock to measure the time between pulses or the pulse ON time and then display time measurements or

a variety of other calculations.

Function Operation Operation image (application)

Passing

speed

The reciprocal of the time (T) from input A ON to input

B ON is multiplied by 60 and displayed.

Display value D = 1/T × 60 × α, α: Prescaling value

•Recovery time (TR) of 20 ms is required before

starting the next measurement.

Display unit:

mm/s, m/s

m/min, km/h, etc.

Measuring workpiece passing speed between A and B

Cycle

Measures and displays input A cycle (T).

Display value D = T × α, α: Prescaling value

Display unit:

ms, s, min.,

min.s.1/10 s

Measuring feed cycles for parts

Time dif-

ference

Displays the time (T) from input A ON to input B ON.

Display value D = T × α, α: Prescaling value

•Recovery time (TR) of 20 ms is required before

starting the next measurement.

Display unit:

ms, s, min.,

min.s.1/10 s

Function name Function No.

Passing speed f1

Cycle f2

Time difference f3

Time band f4

Measuring length f5

Interval f6

The time (T) between input A pulse and input B pulse

is measured by the internal system clock. If, for

example, the system clock measures 100,000 counts

during time T, then

T = 1 system clock count (0.5 μs) × 100,000

T = 0.05 s

F1 (the passing speed) is calculated internally

using the formula × 60 (m/min), and the

display, in this example, would be × 60=

1200 (m/min).

0.05 s

Input A

Input B

Internal

system clock

Example: F1 Passing Speed

Input A

Input B

Display

HOLD input

TRT1TR

T2TRT3T4

1 × 60 T2

1 × 60 T4

1 × 60

⎛

⎜

⎝

⎞

⎟

⎠

Input A

Display

HOLD input

T1T2T5

T3T4T5T2

Measurement range: 20 ms to 3,200 s

⎛

⎜

⎝

⎞

⎟

⎠

Input A

Input B

Display

HOLD input

T1TRTRTR

T1T3T4

T2T3T4

Measurement range: 10 ms to 3,200 s

⎛

⎜

⎝

⎞

⎟

⎠

Measuring workpiece passing time

between A and B

Measuring the length of a

workpiece step by changing

prescale values.

K3HB-P

■What Is Prescaling?

To make calculations using the input pulse to display the passing speed between two points, the distance between the two points and the display

unit must be set and the internally measured time multiplied by a certain coefficient. This coefficient is called the prescale value. (For information

on settings details, refer to the User's Manual.)

Time Unit Settings Input Type Setting

Note: Set to 10 or 11 when there is a large variation in the display.

The largest measurement range is 30 Hz.

Time band

Displays input A ON time (T).

Display value D = T × α,

α: Prescaling value

•Recovery time (TR) of 20 ms is required before

starting the next measurement.

Display unit:

ms, s, min.,

min.s.1/10 s

Measuring

length

Displays the number of input A pulses while input B is

ON.

Display value D = C × α,

C: Pulse value

α: Prescaling value

•Recovery time (TR) of 20 ms is required before

starting the next measurement.

Display unit:

mm, cm, m, etc.

Measuring workpiece length

Interval

Displays the number of input A pulses from when input

B turns ON until input B turns ON again. Measurement

is made every other time input B turns ON.

Display value D = C × α,

C: Pulse value

α: Prescaling value

•Recovery time (TR) of 20 ms is required before

starting the next measurement.

Display unit:

mm, cm, m, etc.

Measuring slit intervals

Function Operation Operation image (application)

Input A

Display

HOLD input

T1T2TR

T1T3

Measurement range: 10 ms to 3,200 s

⎛

⎜

⎝

⎞

⎟

⎠

Communications

output

Monitoring the ON time of a printing

press

Managing the valve release

time

Input A

Input B

Display

HOLD input

12345 123456

⎛

⎜

⎝

⎞

⎟

⎠

BCD To Programmable Controller

Input A

Input B

Display

HOLD input

1234 1234 121

TRTR

⎛

⎜

⎝

⎞

⎟

⎠

PA S S

OK judgment

12 12 1 23

RTR

INA

INB

Display

Setting Meaning

off Seconds display when prescaling = 1.0000

min Minutes display when prescaling = 1.0000

h.mm.ss h.mm.ss display

mm.ss.d mm.ss.d display (d = tenths of a second)

NO: Voltage pulse high NC: Voltage pulse low

No-contact or

voltage pulse

input

00 01

Contact 10 11

K3HB-P

Common Specifications

■Event Input Ratings

■Output Ratings

Contact Output Transistor Outputs

Linear Output

Serial Communications Output BCD Output I/O Ratings

(Input Signal Logic: Negative)

K3HB-P/-C HOLD, RESET, BANK1, BANK2, BANK4

Contact ON: 1 kΩ max., OFF: 100 kΩ min.

No-contact ON residual voltage: 2 V max.

OFF leakage current: 0.1 mA max.

Load current: 4 mA max.

Maximum applied voltage: 30 VDC max.

Item

Resistive loads

(250 VAC, cosφ=1;

30 VDC, L/R=0 ms)

Inductive loads

(250 VAC, closed

circuit, cosφ=0.4;

30 VDC, L/R=7 ms)

Rated load 5 A at 250 VAC

5 A at 30 VDC

1 A at 250 VAC

1 A at 30 VDC

Mechanical life

expectancy

5,000,000 operations

Electrical life

expectancy

100,000 operations

Maximum load voltage 24 VDC

Maximum load current 50 mA

Leakage current 100 μA max.

Item Outputs 0 to 20 mA 4 to 20 mA 0 to 5 V 1 to 5 V 0 to 10 V

Allowable load impedance 500 Ω max. 5 kΩ min.

Resolution Approx. 10,000

Output error ±0.5% FS ±0.5% FS

(±0.15 V for 1 V or less and no output for 0 V)

Item Type RS-232C, RS-485

Communications method Half duplex

Synchronization method Start-stop synchronization (asynchronous)

Baud rate 9600/19200/38400 bps

Transmission code ASCII

Data length 7 bits or 8 bits

Stop bit length 2 bits or 1 bit

Error detection Vertical parity and FCS

Parity check Odd, even

I/O signal name Item Rating

Inputs REQUEST

HOLD

MAX

MIN

RESET

Input signal No-voltage

contact input

Input current for no-voltage input 10 mA

Signal level ON voltage 1.5 V max.

OFF voltage 3 V min.

Outputs DATA

POLARITY

OVER

DATA VALID

RUN

Maximum load voltage 24 VDC

Maximum load current 10 mA

Leakage current 100 μA max.

PA S S

Maximum load voltage 24 VDC

Maximum load current 50 mA

Leakage current 100 μA max.

Refer to the K3HB Communications User's Manual (Cat. No. N129)

for details on serial and DeviceNet communications.

K3HB-P

DeviceNet Communications

Communications protocol Conforms to DeviceNet

Supported

communications

Remote I/O

communications Master-Slave connection (polling, bit-strobe, COS, cyclic)

Conforms to DeviceNet communications standards.

I/O allocations Allocate any I/O data using the Configurator.

Allocate any data, such as DeviceNet-specific parameters and variable area for Digital Indicators.

Input area: 2 blocks, 60 words max.

Output area: 1 block, 29 words max.

(The first word in the area is always allocated for the Output Execution Enabled Flags.)

Message

communications Explicit message communications

CompoWay/F communications commands can be executed

(using explicit message communications)

Connection methods Combination of multi-drop and T-branch connections (for trunk and drop lines)

Baud rate DeviceNet: 500, 250, or 125 Kbps (automatic follow-up)

Communications media Special 5-wire cable (2 signal lines, 2 power supply lines, 1 shield line)

Communications distance

The values in parentheses are for Thick Cable.

Communications power supply 24-VDC DeviceNet power supply

Allowable voltage fluctuation range 11 to 25-VDC DeviceNet power supply

Current consumption 50 mA max. (24 VDC)

Maximum number of nodes 64 (DeviceNet Configurator is counted as one node when connected.)

Maximum number of slaves 63

Error control checks CRC errors

DeviceNet power supply Supplied from DeviceNet communications connector

Baud rate Network length

(max.)

Drop line length

(max.)

Total drop line length

(max.)

500 Kbps 100 m max.

(100 m max.)

6 m max. 39 m max.

250 Kbps 100 m max.

(250 m max.)

6 m max. 78 m max.

125 Kbps 100 m max.

(500 m max.)

6 m max. 156 m max.

K3HB-P

Connections

The BCD COMMON is shared.

The pins indicated in the above diagram

as blank (white) boxes have been removed.

Only one of the following can be used for each Digital Indicator: communications, BCD, or DeviceNet.

DeviceNet Connector (Included)

<DRT>

1 2 3 4 5

Relay Outputs

<C2>

Relay Outputs

<C1>

Transistor Outputs

NPNPNP

PA S S

COM

RS-232C

<FLK1A>

RS-485

<FLK3A>

−

N/C

12 VDC

80 mA

B (+)

A (−)

B (+)

A (−)

12 VDC

80 mA

12 VDC

80 mA

12 VDC

80 mA

0-20/

4-20 mA

N/C

0-5/1-5/

0-10 VN/C

<A>

12 VDC

80 mA

−

<CPA>

12 VDC

80 mA

N/C

PA S S

Sensor

power

supply

COM

LLL

COM

Sensor

power

supply

Sensor

power

supply

Sensor power supply + communications

Sensor power supply

Sensor

power

supply

ABCDE

100 to 240 VAC

24 VAC/VDC

PASS

BCD (NPN Open Collector): <BCD>

Special Cable (Sold separately)

K32-BCD (OMRON)

(HDR-E50MAG1 with 0.3-m cable)

5 V

PA SS

A Operating Power Supply

*Check the required power supply type.

Sensor power supply + PASS output

Sensor power supply + linear output

B Sensor Power Supply/Output

Relays, Transistors, BCD and DeviceNet

1: V− (Power supply cable: Black)

2: CAN L (Communications cable: Blue)

3: Shield

4: CAN H (Communications cable: White)

5: V+ (Power supply cable: Red)

Applicable Connector:

HR31-5.08P-5SC (01)

(HIROSE ELECTRIC CO., LTD.)

* Attach the provided crimp terminals.

Contact Outputs Transistor Outputs

(NPN Open Collector)

Safety Standards Conformance

Always use a EN/IEC-compliant power supply with reinforced insulation or double

insulation for the DeviceNet power supply.

The product must be used indoors for the above applicable standards to apply.

■External Connection Diagrams

Terminal Arrangements

Note: Refer to Internal Block Diagram on page 10 for information on isolation.

K3HB-P

BCD Output Cable

Note: The BCD Output Cable has a D-sub plug. Cover: 17JE-37H-1A (manufactured by DDK); Connector: equivalent to 17JE-23370-02 (D1)

(manufactured by DDK)

Special Cable (for Event Inputs with 8-pin Connector)

Model Shape Pin arrangement

K32-BCD

Model Appearance Wiring

K32-DICN

Models with Terminal Blocks

<1> <3>

1: N/C

3: HOLD

5: N/C

7: BANK4

9: BANK1

2: N/C

4: RESET

6: COM

8: BANK2

10: COM

Models with Connectors

<2> <4>

COM

• Use terminal pin D6 as the common terminal.

• Use NPN open collector or no-voltage contacts

for event input.

PNP types are also available.

COM

E Pulse Inputs

3.9 kΩ

4.7 kΩ

S-TMR : D2

HOLD : D3

RESET : D4

12 V

COM

NPN PNP

Input A

Voltage

NPN PNP

Input B

Voltage

D Event Inputs

NPN Input:

K3HB-@NB

Input A

Input B

PNP Input:

K3HB-@PB

Note: E3 and E6,

as well as B6,

are internally

connected.

Note: E3 and E6, as

well as B5,

are internally

connected.

Note: A 2-wire DC sensor can also be

connected. Check the ratings and

characteristics tables, however, for

the connection conditions.

COM

E3, E6

E2, E5

700 Ω

510 Ω

12 V

E3, E6

E1, E4

10 kΩ700 Ω

510 Ω

12 V

COM

700 Ω

E2, E5 510 Ω

12 V

E3, E6

NPN Input Model

• NPN input section

• Voltage pulse input section

PNP Input Model

• Applicable Connector (Sold separately)

XG4M-1030 (OMRON)

• Special Cable (Sold separately)

K32-DICN (OMRON)

(XG4M-1030 with 3-m cable)

N/C

HOLD

COM

N/C

RESET

• Timer Interval Meter: K3HB-P

Connectable Sensors ON residual voltage: 3 V

OFF leakage current: 1.5 mA max.

Connectable Sensors ON voltage: 4.5 to 30 V

OFF voltage: -30 to 2 V

38 mm 46.5 mm

300 mm

K3HB end

Connected device end

(PLC, display device, etc.)

Cover: HDR-E50LPA5

(manufactured by Honda Tsushin Co., Ltd)

Connector: HDR-E50MAG1

(manufactured by Honda Tsushin Co., Ltd)

D-sub connector (37-pin female)

Cover: 17JE-37H-1A (manufactured by DDK)

Connector: Equivalent to 17JE-13370-02

(manufactured by DDK)

Stud: 17L-002A (manufactured by DDK)

100

101

102

103

104

OVER

DATA VALID

RUN

COMMON

REQUEST

MAX REQ.

MIN REQ.

HOLD

RESET

POLARITY

PA S S

COMMON

COMMON4

3,000 mm

(3 m)

Cable marking

910

Pin No.

Signal name

N/C

S-TMR

HOLD

RESET

N/C

COM

BANK4

BANK2

BANK1

COM

K3HB-P

■Derating Curve for Sensor Power Supply (Reference Values)

For 12V

Note: 1. The above values were obtained under test conditions with the standard mounting. The derating curve will vary with the mounting

conditions, so be sure to adjust accordingly.

2. Internal components may be deteriorated or damaged. Do not use the Digital Indicator outside of the derating range (i.e., do not use it in

the area labeled A, above).

■Internal Block Diagram

140

120

100

−20 −100 102030405060

Ambient temperature (°C)

Maximum current (mA)

Keys

Micro-

computer

Waveform

shaping circuit

Waveform

shaping circuit

Drive

circuit

Indications

EEPROM

Drive

circuit

Digital input

circuit

Linear output

circuit

Filter

Pulse input

circuit

BCD

• Input circuit

• Output circuit

• Transistor

output circuit

Drive

circuit

Drive

circuit

Drive

circuit

Drive

circuit

Transistor

output

Relay output

Pulse input

BCD I/O

Event input

Linear output

Sensor power

supply

DeviceNet

Communications

DeviceNet

circuit

Communi-

cations

driver

Power supply

Power supply circuit (isolated)

COM

DC-DC

Converter (isolated)

K3HB-P

■BCD Output Timing Chart

A REQUEST signal from a Programmable Controller or other external device is required to read BCD data.

Single Sampling Data Output

The data is set in approximately 30 ms from the rising edge of the

REQUEST signal and the DATA VALID signal is output.

When reading the data from a Programmable Controller, start

reading the data when the DATA VALID signal turns ON.

The DATA VALID signal will turn OFF 40 ms later, and the data will

turn OFF 16 ms after that.

Continuous Data Output

Measurement data is output every 64 ms while the REQUEST signal

remains ON.

Note: If HOLD is executed when switching between data 1 and data

2, either data 1 or data 2 is output depending on the timing of

the hold signal. The data will not go LOW.

Approx.

30 ms

All data "High" All data "High"

40 ms 16 ms

Data

REQ.

MAX.MIN.

DATA

VALID

20-ms pulse min. (50 ms max.)

Approx.

30 ms

Data 1 Data 2

REQ.

MAX.MIN.

DATA

VALID

64 ms 64 ms

40 ms 40 ms

24 ms 24 ms

All data "High"

K3HB

(1) Programmable

Controller

K3HB

(2)

K3HB

(3)

DATA (including POL and

OVER) and DATA VALID can

be used in a wired OR.

RUN, HH, H, PASS, L, and

LL are always output, with or

without a REQUEST signal.

Do not used a wired OR

connect for these signals.

DATA

REQ. (1)

(1) (2) (3)

REQ. (2)

REQ. (3)

DATA

VALID

Note: Leave 20 ms min. between DATA VALID turning OFF and the REQUEST signal.

(See note.) (See note.)

(See note.)

•The K3HB BCD output model has an open collector output, so wired OR connection is possible

Programmable Controller Connection Example

Digital Indicator SYSMAC Programmable Controller

DC Input Unit

1.COMMON

Connector pin No. (See note.)

COM

OUT

COM

24 VDC

(0 V)

2.1

3.2

4.4

5.8

23.DATA VALID

24.RUN

25.COMMON

26.REQUEST

30.RESET

31.POLARITY

(+/− polarity)

10°

240 Ω

+5 V

+24 V

0 V

DC power

supply

Transistor Output Unit

Internal circuit

Display Unit Connection Example

To 102

SEC

Digital Indicator

1.COMMON

Connector pin No. (See note.)

2.1

3.2

4.4

5.8

23.DATA VALID

24.RUN

25.COMMON

26.REQUEST

30.RESET

M7E-01D@N2, 01H@N2

31.POLARITY

(+/− polarity)

10°

To 101

240 Ω

+5 V

Short-

circuit

Note: The BCD output connector pin number is the D-sub connector pin number when

the BCD Output Cable (sold separately) is connected. This number differs from

the pin number for the Digital Indicator narrow pitch connector (manufactured by

Honda Tsushin Kogyo Co., Ltd.).

Refer to the following User's Manual for application precautions and other information required when using the Digital Indicator:

K3HB-R/P/C Digital Indicator User's Manual (Cat. No. N136)

The manual can be downloaded from the following site in PDF format: OMRON Industrial Web http://www.fa.omron.co.jp

K3HB-P

■Component Names and Functions

UPMODELEVEL

CMW

Max

Min

Hold

MAX/MIN

HH H

TLLL

SHIFT

MAX/MIN Key LEVEL Key MODE Key SHIFT Key UP Key

When changing a set

value, this key is used

to change the actual

value.

When a measurement

value is displayed, this

key is used to execute

or clear the forced-zero

function or to execute

teaching.

Used to change

parameter settings.

When changing a set

value, this key is used

to move along the

digits.

Used to switch the

parameters displayed.

Used to switch level.Used to switch the

display between the PV,

maximum value, and

minimum value and to

reset the maximum and

minimum values.

PV display

SV display

Position meter

SV display status indicators

Displays PVs, maximum values,

minimum values, parameter

names, and error names.

Displays SV and monitor values.

Displays the position of the PV

with respect to a desired scale.

Comparative output

status indicators

Level/bank display

Status indicators

Display

Display the status of comparative

outputs.

Turns ON when the maximum value or minimum

value is displayed in the RUN level.

In RUN level, displays the bank if the bank function is

ON. (Turns OFF if the bank function is OFF.)

In other levels, displays the current level.

Hold

CMW

Function

Lit when communications writing is ON

(enabled) and not lit when OFF (prohibited).

Turns ON/OFF when hold input turns

ON/OFF.

Max./Min. status indicator

Indicator

Function

HH, H,

L, LL

In RUN level, turn ON when the

comparative set value HH, H, L, or LL

is displayed.

HH H

LL L

K3HB-P

■Dimensions

Wiring Precautions

•For terminal blocks, use the crimp terminals suitable for M3 screws.

•Tighten the terminal screws to the recommended tightening torque

of approx. 0.5 N·m.

•To prevent inductive noise, separate the wiring for signal lines from

that for power lines.

Wiring

• Use the crimp terminals suitable for M3 screws shown below.

Unit Stickers (included)

•No unit stickers are attached to the Digital Indicator.

•Select the appropriate units from the unit sticker sheets provided.

Mounting Method

1. Insert the K3HB into the mounting cutout in the panel.

2. Insert watertight packing around the Unit to make the mounting

watertight.

Insert the adapter into the grooves on the left and right sides of the

rear case and push until it reaches the panel and is fixed in place.

LCD Field of Vision

The K3HB is designed to have the best visibility at the angles shown

in the following diagram.

Character Size for Main Display (mm)

Terminal cover (included)

PV display SV display

14.2 4.9

3.5

7.6

1.3

(112)

100

101.2

44.8

Panel Cutout Dimensions

+0.6

+0.8

75 min.

95 *1

120 min. *2

Terminal: M3, Terminal Cover: Accessory

*1. DeviceNet models: 97 mm

*2. Leave a distance of at least 140 mm when using

the Watertight Cover Y92A-49N.

Note: Mounting Recommended Panel

Thickness 1 to 8 mm.

Mount the product horizontally.

Note: For measurements for commercial purposes, be sure to use

the unit required by any applicable laws or regulations.

5.8 mm max.

Watertight

packing

Adaptor

10°

30°

Watertight Cover

Y92A-49N

Rubber Packing

K32-P1 If the rubber packing is lost or damaged, it can be ordered

using the following model number: K32-P1.

(Depending on the operating environment,

deterioration, contraction, or hardening of the rubber packing

may occur and so, in order to ensure the level of waterproofing

specified in NEMA4, periodic replacement is

recommended.)

Note: Rubber packing is provided with the Controller.

K3HB-P

Main Functions

■Main Functions and Features

Measurement

The K3HB-R has the following six functions for receiving and

displaying input pulses.

F1: Rotation (rpm)/circumferential speed

F2: Absolute ratio

F3: Error ratio

F4: Rotational difference

F5: Flow rate ratio

F6: Passing time

The K3HB-P has the following six functions for receiving and

displaying input pulses.

F1: Passing speed

F2: Cycle

F3: Time difference

F4: Time band

F5: Measuring length

F6: Interval

The K3HB-C has the following three functions for receiving and

displaying input pulses.

F1: Individual inputs

F2: Phase differential inputs

F3: Pulse counting input

Filters

Specify the types of sensor connected to input A and input B.

Key Operations

Key protection restricts level or parameter changes using the keys to

prevent unintentional key operations and malfunctions.

Outputs

Standard, zone, and level comparative output patterns can be

selected for comparative outputs.

Holds the output status when a comparative result output other than

PASS turns ON.

Comparative results other than PASS can be output from the PASS

output terminal.

Delays turning OFF comparatives for a set period. This can be used

to provide sufficient time to read the comparative output ON status

when the comparative result changes at short intervals.

Turns ON the comparative output for a specific time.

Reverses the output logic of comparative results.

Output operation can be checked without using actual input signals

by using the keys to set a test measurement value.

A current or voltage proportional to the change in the measurement

value can be output.

The comparison outputs can be kept OFF until the measurement

value enters the PASS range.

Function func

Input Types in-ta, in-tb

in-ta

Key Protection

Comparative Output Pattern out-p

Output Refresh Stop o-stp

PASS Output Change pass

Output OFF Delay off-d

Shot Output shot

Output Logic out-n

Output Test test

Linear Outputs lset.c, lset.v, lset.h, lset.l

Standby Sequence stdby

K3HB-P

Display

The display value can be set to the present value, the maximum

value, or the minimum value.

The present value display color can be set to green or red. The color

of the present value can also be switched according to the

comparative output.

When the input changes rapidly, the display refresh period can be

lengthened to control flickering and make the display easier to read.

The present measurement value can be displayed as a position in

relation to the scaling width on a 20-gradation position meter.

The input signal can be converted and displayed as any value.

Select whether or not to display the comparative value during

operation.

Automatically returns the display to RUN level when there are no key

operations (e.g., max./min. switching, bank settings using keys).

Other

Holds the maximum and minimum measurement values.

Switch between 8 comparative value banks using the keys on the

front panel or external inputs. A set of set comparative values can be

selected as a group.

Any bank settings can be copied to all banks.

Display Value Selection disp

Display Color Selection color

Display Refresh Period d.ref

Position Meter pos-t, pos-h, pos-l

Prescale ps.ax, ps.ay, ps.bx, ps.by

Comparative Set Value Display sv.dsp

Display auto-return ret

Max./Min. Hold

Bank Selection bnk-c

Bank Copy copy

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2014.11

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:

K3HB-PPB 100-240VAC K3HB-PNB 24VAC/VDC K3HB-PNB 100-240VAC K3HB-PPB 24VAC/VDC