LTC2604/LTC2614/LTC2624 Quad 16-Bit Rail-to-Rail DACs in 16-Lead SSOP U FEATURES DESCRIPTIO The LTC(R)2604/LTC2614/LTC2624 are quad 16-,14- and 12-bit 2.5V to 5.5V rail-to-rail voltage output DACs in 16-lead narrow SSOP packages. These parts have separate reference inputs for each DAC. They have built-in high performance output buffers and are guaranteed monotonic. Smallest Pin Compatible Quad 16-Bit DAC: LTC2604: 16-Bits LTC2614: 14-Bits LTC2624: 12-Bits Guaranteed 16-Bit Monotonic Over Temperature Separate Reference Inputs for each DAC Wide 2.5V to 5.5V Supply Range Low Power Operation: 250A per DAC at 3V Individual DAC Power-Down to 1A, Max Ultralow Crosstalk Between DACs (<5V) High Rail-to-Rail Output Drive (15mA) Double Buffered Digital Inputs LTC2604-1/LTC2614-1/LTC2624-1: Power-On Reset to Midscale 16-Lead Narrow SSOP Package U APPLICATIO S Mobile Communications Process Control and Industrial Automation Instrumentation Automatic Test Equipment These parts establish advanced performance standards for output drive, crosstalk and load regulation in singlesupply, voltage output multiples. The parts use a simple SPI/MICROWIRETM compatible 3-wire serial interface which can be operated at clock rates up to 50MHz. Daisy-chain capability and a hardware CLR function are included. The LTC2604/LTC2614/LTC2624 incorporate a poweron reset circuit. During power-up, the voltage outputs rise less than 10mV above zero scale; and after power-up, they stay at zero scale until a valid write and update take place. The power-on reset circuit resets the LTC2604-1/ LTC2614-1/LTC2624-1 to midscale. The voltage outputs stay at midscale until a valid write and update take place. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. W BLOCK DIAGRA VCC GND 1 REF LO 2 REF A 16 REF B DAC B 6 CS/LD 7 CONTROL LOGIC DECODE SCK 8 DAC REGISTER DAC D 1.0 14 VCC = 5V VREF = 4.096V 0.8 32-BIT SHIFT REGISTER DAC REGISTER VOUT C DAC C 13 REF C 12 0.4 ERROR (LSB) 5 Differential Nonlinearity (LTC2604) VOUT D 0.6 INPUT REGISTER VOUTB INPUT REGISTER DAC A INPUT REGISTER 4 DAC REGISTER VOUTA DAC REGISTER 3 INPUT REGISTER REF D 15 0.2 0 -0.2 CLR 11 -0.4 SDO -0.8 10 -1.0 SDI 9 -0.6 0 16384 32768 CODE 49152 65535 2604 TA01 2604 BD 2604fb 1 LTC2604/LTC2614/LTC2624 W U U W W W AXI U U ABSOLUTE PACKAGE/ORDER I FOR ATIO RATI GS (Note 1) TOP VIEW Any Pin to GND ........................................... - 0.3V to 6V Any Pin to VCC ............................................ - 6V to 0.3V Maximum Junction Temperature ......................... 125C Operating Temperature Range LTC2604C/LTC2614C/LTC2624C .......... 0C to 70C LTC2604C-1/LTC2614C-1/ LTC2624C-1 .......................................... 0C to 70C LTC2604I/LTC2614I/LTC2624I .......... - 40C to 85C LTC2604I-1/LTC2614I-1/ LTC2624I-1 ....................................... - 40C to 85C Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................ 300C GND 1 16 VCC REF LO 2 15 REF D REF A 3 14 VOUT D VOUT A 4 13 VOUT C VOUT B 5 12 REF C REF B 6 11 CLR CS/LD 7 10 SDO SCK 8 9 SDI GN PACKAGE 16-LEAD PLASTIC SSOP TJMAX = 125C, JA = 150C/W GN PART MARKING ORDER PART NUMBER LTC2604CGN LTC2614IGN 2604 2614I LTC2604CGN-1 LTC2614IGN-1 26041 2614I1 LTC2604IGN LTC2624CGN 2604I 2624 LTC2604IGN-1 LTC2624CGN-1 2604I1 26241 LTC2614CGN LTC2624IGN 2614 2624I LTC2614CGN-1 LTC2624IGN-1 26141 2624I1 Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. REF A = REF B = REF C = REF D = 4.096V (VCC = 5V), REF A = REF B = REF C = REF D = 2.048V (VCC = 2.5V), REF LO = 0V, VOUT unloaded, unless otherwise noted. (Note 10) SYMBOL PARAMETER DC Performance Resolution Monotonicity DNL Differential Nonlinearity INL Integral Nonlinearity Load Regulation ZSE VOS GE SYMBOL PSR Zero-Scale Error Offset Error VOS Temperature Coefficient Gain Error Gain Temperature Coefficient PARAMETER Power Supply Rejection LTC2624/LTC2624-1 LTC2614/LTC2614-1 LTC2604/LTC2604-1 MIN TYP MAX MIN TYP MAX MIN TYP MAX CONDITIONS (Note 2) (Note 2) (Note 2) VREF = VCC = 5V, Midscale IOUT = 0mA to 15mA Sourcing IOUT = 0mA to 15mA Sinking VREF = VCC = 2.5V, Midscale IOUT = 0mA to 7.5mA Sourcing IOUT = 0mA to 7.5mA Sinking 16 16 Bits Bits LSB LSB 0.9 0.5 4 4 1 16 14 1 64 0.025 0.125 0.025 0.125 0.1 0.1 0.5 0.5 0.3 0.3 2 2 LSB/mA LSB/mA 0.05 0.05 1.5 1.5 5 0.2 0.2 1.5 1.5 5 1 1 9 9 0.7 0.7 1.5 1.5 5 4 4 9 9 LSB/mA LSB/mA mV mV V/C 0.1 0.7 5 %FSR ppm/C CONDITIONS VCC = 5V 10% VCC = 3V 10% 14 14 (Note 7) 12 12 UNITS 0.25 0.25 9 9 0.1 0.7 5 0.1 0.7 5 MIN TYP -80 -80 MAX UNITS dB dB 2604fb 2 LTC2604/LTC2614/LTC2624 ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. REF A = REF B = REF C = REF D = 4.096V (VCC = 5V), REF A = REF B = REF C = REF D = 2.048V (VCC = 2.5V), REF LO = 0V, VOUT unloaded, unless otherwise noted. (Note 10) SYMBOL ROUT PARAMETER DC Output Impedance DC Crosstalk (Note 4) ISC Short-Circuit Output Current Reference Input Input Voltage Range Resistance Capacitance IREF Reference Current, Power Down Mode Power Supply VCC Positive Supply Voltage ICC Supply Current Digital I/O VIH Digital Input High Voltage VIL Digital Input Low Voltage VOH VOL ILK CIN Digital Output High Voltage Digital Output Low Voltage Digital Input Leakage Digital Input Capacitance SYMBOL PARAMETER AC Performance ts Settling Time (Note 8) Settling Time for 1LSB Step (Note 9) en Voltage Output Slew Rate Capacitive Load Driving Glitch Impulse Multiplying Bandwidth Output Voltage Noise Density Output Voltage Noise CONDITIONS VREF = VCC = 5V, Midscale; -15mA IOUT 15mA VREF = VCC = 2.5V, Midscale; -7.5mA IOUT 7.5mA Due to Full Scale Output Change (Note 5) Due to Load Current Change Due to Powering Down (per Channel) VCC = 5.5V, VREF = 5.5V Code: Zero Scale; Forcing Output to VCC Code: Full Scale; Forcing Output to GND VCC = 2.5V, VREF = 2.5V Code: Zero Scale; Forcing Output to VCC Code: Full Scale; Forcing Output to GND UNITS V V/mA V 34 36 60 60 mA mA 7.5 7.5 18 24 50 50 mA mA 0 88 VCC 160 1 V k pF A 5.5 2 1.6 1 1 V mA mA A A All DACs Powered Down For Specified Performance VCC = 5V (Note 3) VCC = 3V (Note 3) All DACs Powered Down (Note 3) VCC = 5V All DACs Powered Down (Note 3) VCC = 3V VCC = 2.5V to 5.5V VCC = 2.5V to 3.6V VCC = 4.5V to 5.5V VCC = 2.5V to 5.5V Load Current = -100A Load Current = +100A VIN = GND to VCC (Note 6) At Midscale Transition MAX 0.15 0.15 15 15 0.024% (1LSB at 12 Bits) 0.006% (1LSB at 14 Bits) 0.0015% (1LSB at 16 Bits) 0.024% (1LSB at 12 Bits) 0.006% (1LSB at 14 Bits) 0.0015% (1LSB at 16 Bits) TYP 0.025 0.030 5 1 3.5 Normal Mode CONDITIONS At f = 1kHz At f = 10kHz 0.1Hz to 10Hz MIN 128 14 0.001 2.5 1.3 1 0.35 0.10 2.4 2.0 0.8 0.6 VCC - 0.4 0.4 1 8 LTC2624/LTC2624-1 LTC2614/LTC2614-1 LTC2604/LTC2604-1 MIN TYP MAX MIN TYP MAX MIN TYP MAX 7 7 9 2.7 2.7 4.8 0.80 1000 12 180 120 100 15 0.80 1000 12 180 120 100 15 7 9 10 2.7 4.8 5.2 0.80 1000 12 180 120 100 15 V V V V V V A pF UNITS s s s s s s V/s pF nV * s kHz nV/Hz nV/Hz VP-P 2604fb 3 LTC2604/LTC2614/LTC2624 WU TI I G CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. REF A = REF B = REF C = REF D = 4.096V (VCC = 5V), REF A = REF B = REF C = REF D = 2.048V (VCC = 2.5V), REF LO = 0V, VOUT unloaded, unless otherwise noted. (Note 10) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VCC = 2.5V to 5.5V t1 SDI Valid to SCK Setup 4 ns t2 SDI Valid to SCK Hold 4 ns t3 SCK High Time 9 ns t4 SCK Low Time 9 ns t5 CS/LD Pulse Width 10 ns t6 LSB SCK High to CS/LD High 7 ns t7 CS/LD Low to SCK High 7 ns t8 SDO Propagation Delay from SCK Falling Edge t9 CLR Pulse Width t10 CS/LD High to SCK Positive Edge CLOAD = 10pF VCC = 4.5V to 5.5V VCC = 2.5V to 5.5V SCK Frequency 20 7 ns ns ns ns 50% Duty Cycle Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Linearity and monotonicity are defined from code kL to code 2N - 1, where N is the resolution and kL is given by kL = 0.016(2N/VREF), rounded to the nearest whole code. For VREF = 4.096V and N = 16, kL = 256, linearity is defined from code 256 to code 65,535. Note 3: Digital inputs at 0V or VCC. Note 4: DC crosstalk is measured with VCC = 5V and VREF = 4.096V, with the measured DAC at midscale, unless otherwise noted. 20 45 50 MHz Note 5: RL = 2k to GND or VCC. Note 6: Guaranteed by design and not production tested. Note 7: Inferred from measurement at code 256 (LTC2604), code 64 (LTC2614) or code 16 (LTC2624), and at full scale. Note 8: VCC = 5V, VREF = 4.096V. DAC is stepped 1/4 scale to 3/4 scale and 3/4 scale to 1/4 scale. Load is 2k in parallel with 200pF to GND. Note 9: VCC = 5V, VREF = 4.096V. DAC is stepped 1LSB between half scale and half scale -1. Load is 2k in parallel with 200pF to GND. Note 10: These specifications apply to LTC2604/LTC2604-1, LTC2614/ LTC2614-1, LTC2624/LTC2624-1. U W TYPICAL PERFOR A CE CHARACTERISTICS (LTC2604/LTC2604-1, LTC2614/LTC2614-1, LTC2624/LTC2624-1) Current Limiting 0.06 VOUT (V) 0.04 1.0 CODE = MIDSCALE VREF = VCC = 5V 0.4 0 -0.04 -0.06 VREF = VCC = 3V 0.2 0 -0.2 VREF = VCC = 5V -0.4 VREF = VCC = 5V 1 0 -1 VREF = VCC = 3V -0.6 -2 -0.8 -0.08 -0.10 -40 -30 -20 -10 0 10 IOUT (mA) 2 0.6 VREF = VCC = 3V 0.02 -0.02 3 CODE = MIDSCALE 0.8 OFFSET ERROR (mV) 0.08 VOUT (mV) 0.10 Offset Error vs Temperature Load Regulation 20 30 40 2604 G01 -1.0 -35 -25 -15 -5 5 IOUT (mA) 15 25 35 2604 G02 -3 -50 -30 -10 10 30 50 TEMPERATURE (C) 70 90 2604 G03 2604fb 4 LTC2604/LTC2614/LTC2624 U W TYPICAL PERFOR A CE CHARACTERISTICS (LTC2604/LTC2604-1, LTC2614/LTC2614-1, LTC2624/LTC2624-1) Zero-Scale Error vs Temperature Gain Error vs Temperature 3 3 0.3 2.0 1.5 1.0 2 0.2 OFFSET ERROR (mV) GAIN ERROR (%FSR) 2.5 ZERO-SCALE ERROR (mV) Offset Error vs VCC 0.4 0.1 0 -0.1 0 -1 -0.2 0.5 -2 -0.3 0 -50 -30 -10 10 30 50 TEMPERATURE (C) 70 90 -0.4 -50 -30 -10 10 30 50 TEMPERATURE (C) 70 2604 G04 90 -3 2.5 0.3 400 0.2 350 0.1 300 ICC (nA) 450 4 VCC (V) 4.5 5 5.5 Large-Signal Settling VOUT 0.5V/DIV 250 200 -0.1 VREF = VCC = 5V 1/4-SCALE TO 3/4-SCALE 150 -0.2 3.5 2604 G06 ICC Shutdown vs VCC 0.4 0 3 2604 G05 Gain Error vs VCC GAIN ERROR (%FSR) 1 100 -0.3 2.5s/DIV 50 -0.4 2.5 3 3.5 4 VCC (V) 4.5 5 5.5 0 2.5 3 3.5 4 VCC (V) 4.5 5 2604 G09 5.5 2604 G08 2604 G07 Midscale Glitch Impulse Power-On Reset to Midscale Power-On Reset Glitch VREF = VCC VOUT 10mV/DIV VCC 1V/DIV 12nV-s TYP VCC 1V/DIV VOUT 1V/DIV 4mV 4mVPEAK PEAK CS/LD 5V/DIV VOUT 10mV/DIV 2.5s/DIV 2604 G10 250s/DIV 2604 G11 500s/DIV 2604 G34 2604fb 5 LTC2604/LTC2614/LTC2624 U W TYPICAL PERFOR A CE CHARACTERISTICS (LTC2604/LTC2604-1, LTC2614/LTC2614-1, LTC2624/LTC2624-1) Headroom at Rails vs Output Current Supply Current vs Logic Voltage VCC = 5V SWEEP SCK, SDI AND CS/LD 0V TO VCC 5V SOURCING 4.5 1.8 4.0 3.5 3.0 VCC = 5V VREF = 2V VOUT 0.5V/DIV 1.6 3V SOURCING ICC (mA) VOUT (V) Exiting Power-Down to Midscale 2.0 5.0 2.5 2.0 DACs A-C IN POWER-DOWN MODE 1.4 CS/LD 5V/DIV 1.2 1.5 5V SINKING 1.0 1.0 3V SINKING 0.5 0 2.5s/DIV 2604 G14 0.8 0 1 2 3 4 5 6 IOUT (mA) 7 8 9 0 10 0.5 1 1.5 2 2.5 3 3.5 LOGIC VOLTAGE (V) 4 4.5 2604 G12 5 2604 G13 Hardware CLR Hardware CLR to Midscale Multiplying Frequency Response 0 VCC = 5V VREF = 4.096V CODE = FULL SCALE VOUT 1V/DIV VOUT 1V/DIV -3 -6 -9 -12 dB -15 -18 -21 CLR 5V/DIV CLR 5V/DIV -24 2604 G15 1s/DIV VCC = 5V VREF (DC) = 2V VREF (AC) = 0.2VP-P CODE = FULL SCALE -27 -30 2604 G35 1s/DIV -33 -36 1k 1M 10k 100k FREQUENCY (Hz) 2604 G16 Output Voltage Noise, 0.1Hz to 10Hz Short-Circuit Output Current vs VOUT (Sinking) Short-Circuit Output Current vs VOUT (Sourcing) 50 0 V CC = 5.5V V REF = 5.6V CODE = 0 V OUT SWEPT 0V TO V CC 40 0 1 2 3 4 5 6 SECONDS 7 8 9 10 2604 G17 -10 30 10mA/DIV 10mA/DIV VOUT 10V/DIV 20 10 0 V CC = 5.5V V REF = 5.6V CODE = FULL SCALE V OUT SWEPT V CC TO 0V -20 -30 -40 0 1 2 3 1V/DIV 4 5 6 2604 G18 -50 0 1 2 3 1V/DIV 4 5 6 2604 G19 2604fb 6 LTC2604/LTC2614/LTC2624 U W TYPICAL PERFOR A CE CHARACTERISTICS Integral Nonlinearity (INL) 32 Differential Nonlinearity (DNL) 1.0 VCC = 5V VREF = 4.096V 24 (LTC2604/LTC2604-1) INL vs Temperature 32 VCC = 5V VREF = 4.096V 0.8 16 0.4 0 -8 0.2 0 -0.2 0 -8 -0.4 -16 -24 -0.8 0 16384 32768 CODE 49152 65535 -1.0 0 16384 32768 CODE 49152 DNL vs Temperature INL vs VREF VCC = 5V VREF = 4.096V 70 90 DNL vs VREF VCC = 5.5V 24 VCC = 5.5V 1.0 16 0.4 DNL (POS) INL (LSB) 0.2 0 -0.2 0.5 INL (POS) 8 0 -8 DNL (NEG) -0.4 INL (NEG) DNL (POS) 0 DNL (NEG) -0.5 -16 -0.6 -1.0 -24 -0.8 -1.0 -50 -10 10 30 50 TEMPERATURE (C) 1.5 DNL (LSB) 0.6 -30 2604 G22 32 1.0 0.8 -32 -50 65535 2604 G21 2604 G20 DNL (LSB) INL (NEG) -16 -0.6 -24 -32 INL (POS) 8 INL (LSB) 8 DNL (LSB) INL (LSB) 16 VCC = 5V VREF = 4.096V 24 0.6 -32 -30 -10 10 30 50 TEMPERATURE (C) 70 90 0 1 2 3 VREF (V) 4 5 -1.5 0 1 2 3 VREF (V) 2604 G24 2604 G23 Settling to 1LSB 4 5 2604 G25 Settling of Full-Scale Step VOUT 100V/DIV VOUT 100V/DIV 9.7s 12.3s CS/LD 2V/DIV CS/LD 2V/DIV 2s/DIV VCC = 5V, VREF = 4.096V 1/4-SCALE TO 3/4-SCALE STEP RL = 2k, CL = 200pF AVERAGE OF 2048 EVENTS 2604 G26 5s/DIV 2604 G27 VCC = 5V, VREF = 4.096V CODE 512 TO 65535 STEP AVERAGE OF 2048 EVENTS SETTLING TO 1LSB 2604fb 7 LTC2604/LTC2614/LTC2624 U W TYPICAL PERFOR A CE CHARACTERISTICS (LTC2614/LTC2614-1) Integral Nonlinearity (INL) 8 1.0 VCC = 5V VREF = 4.096V 6 Settling to 1LSB Differential Nonlinearity (DNL) VCC = 5V VREF = 4.096V 0.8 0.6 4 0.4 DNL (LSB) INL (LSB) 2 0 -2 VOUT 100V/DIV 0.2 0 CS/LD 2V/DIV -0.2 -4 -0.6 -6 -8 8.9s -0.4 0 4096 8192 CODE 12288 -1.0 16383 2604 G30 2s/DIV -0.8 0 4096 8192 CODE 12288 2604 G28 VCC = 5V, VREF = 4.096V 1/4-SCALE TO 3/4-SCALE STEP RL = 2k, CL = 200pF AVERAGE OF 2048 EVENTS 16383 2604 G29 (LTC2624/LTC2624-1) 2.0 1.0 VCC = 5V VREF = 4.096V 1.5 Settling to 1LSB Differential Nonlinearity (DNL) Integral Nonlinearity (INL) VCC = 5V VREF = 4.096V 0.8 0.6 1.0 6.8s DNL (LSB) INL (LSB) 0.4 0.5 0 -0.5 VOUT 1mV/DIV 0.2 0 CS/LD 2V/DIV -0.2 -0.4 -1.0 -0.6 -1.5 -0.8 -2.0 -1.0 0 1024 2048 CODE 3072 4095 2s/DIV 0 1024 2604 G31 2048 CODE 3072 4095 2604 G33 VCC = 5V, VREF = 4.096V 1/4-SCALE TO 3/4-SCALE STEP RL = 2k, CL = 200pF AVERAGE OF 2048 EVENTS 2604 G32 U U U PIN FUNCTIONS GND (Pin 1): Analog Ground. REF LO (Pin 2): Reference Low. The voltage at this pin sets the zero scale (ZS) voltage of all DACs. This pin can be raised up to 1V above ground at VCC = 5V or 100mV above ground at VCC = 3V. REF A, REF B, REF C, REF D (Pins 3, 6, 12, 15): Reference Voltage Inputs for each DAC. REF x sets the full scale voltage of the DACs. 0V REF x VCC. VOUT A to VOUT D (Pins 4, 5, 13, 14): DAC Analog Voltage Outputs. The output range is from REF LO to REF x. CS/LD (Pin 7): Serial Interface Chip Select/Load Input. When CS/LD is low, SCK is enabled for shifting data on SDI into the register. When CS/LD is taken high, SCK is disabled and the specified command (see Table 1) is executed. SCK (Pin 8): Serial Interface Clock Input. CMOS and TTL compatible. SDI (Pin 9): Serial Interface Data Input. Data is applied to SDI for transfer to the device at the rising edge of SCK. The LTC2604/LTC2604-1, LTC2614/LTC2614-1, LTC2624/ LTC2624-1 accept input word lengths of either 24 or 32 bits. 2604fb 8 LTC2604/LTC2614/LTC2624 U U U PIN FUNCTIONS SDO (Pin 10): Serial Interface Data Output. The serial output of the shift register appears at the SDO pin. The data transferred to the device via the SDI pin is delayed 32 SCK rising edges before being output at the next falling edge. This pin is used for daisy-chain operation. the DAC voltage outputs to drop to 0V for the LTC2604/ LTC2614/LTC2624. A logic low at this input sets all registers to midscale code and causes the DAC voltage outputs to go to midscale for the LTC2604-1/LTC2614-1/ LTC2624-1. CMOS and TTL compatible. CLR (Pin 11): Asynchronous Clear Input. A logic low at this level-triggered input clears all registers and causes VCC (Pin 16): Supply Voltage Input. 2.5V VCC 5.5V. W BLOCK DIAGRA VCC GND 1 REF LO 2 REF A 16 REF D 15 DAC B 5 REF B INPUT REGISTER DAC REGISTER DAC REGISTER VOUTB VOUT D DAC D INPUT REGISTER DAC REGISTER DAC A 4 INPUT REGISTER DAC REGISTER VOUTA INPUT REGISTER 3 DAC C 14 VOUT C 13 REF C 12 CLR 11 6 CONTROL LOGIC CS/LD 7 SDO DECODE 10 SCK SDI 9 32-BIT SHIFT REGISTER 8 2604 BD WU W TI I G DIAGRA t1 t2 SCK t3 1 t6 t4 2 3 23 24 t10 SDI t5 t7 CS/LD t8 SDO 2604 F01 Figure 1 2604fb 9 LTC2604/LTC2614/LTC2624 U OPERATIO Power-On Reset The LTC2604/LTC2614/LTC2624 clear the outputs to zero scale when power is first applied, making system initialization consistent and repeatable. The LTC2604-1/ LTC2614-1/LTC2624-1 set the voltage outputs to midscale when power is first applied. For some applications, downstream circuits are active during DAC power-up, and may be sensitive to nonzero outputs from the DAC during this time. The LTC2604/ LTC2614/LTC2624 contain circuitry to reduce the poweron glitch; furthermore, the glitch amplitude can be made arbitrarily small by reducing the ramp rate of the power supply. For example, if the power supply is ramped to 5V in 1ms, the analog outputs rise less than 10mV above ground (typ) during power-on. See Power-On Reset Glitch in the Typical Performance Characteristics section. Power Supply Sequencing The voltage at REF (Pins 3, 6, 12 and 15) should be kept within the range - 0.3V REF x VCC + 0.3V (see Absolute Maximum Ratings). Particular care should be taken to observe these limits during power supply turn-on and turn-off sequences, when the voltage at VCC (Pin 16) is in transition. Transfer Function The digital-to-analog transfer function is k VOUT(IDEAL) = N [REF x - REFLO] + REFLO 2 where k is the decimal equivalent of the binary DAC input code, N is the resolution and REF x is the voltage at REF A, REF B, REF C and REF D (Pins 3, 6, 12 and 15). Serial Interface The CS/LD input is level triggered. When this input is taken low, it acts as a chip-select signal, powering-on the SDI and SCK buffers and enabling the input shift register. Data (SDI input) is transferred at the next 24 rising SCK edges. The 4-bit command, C3-C0, is loaded first; then the 4-bit DAC address, A3-A0; and finally the 16-bit data word. The data word comprises the 16-, 14- or 12-bit input code, Table 1. COMMAND* C3 C2 C1 C0 0 0 0 0 0 0 0 1 Write to Input Register n Update (Power Up) DAC Register n 0 0 0 0 1 1 0 1 Write to Input Register n, Update (Power Up) All n Write to and Update (Power Up) n 0 1 1 1 0 1 0 1 Power Down n No Operation ADDRESS (n)* A3 A2 A1 A0 0 0 0 0 0 0 0 1 DAC A DAC B 0 0 0 0 1 1 0 1 DAC C DAC D 1 1 1 1 All DACs *Command and address codes not shown are reserved and should not be used. ordered MSB-to-LSB, followed by 0, 2 or 4 don't-care bits (LTC2604, LTC2614 and LTC2624 respectively). Data can only be transferred to the device when the CS/LD signal is low. The rising edge of CS/LD ends the data transfer and causes the device to carry out the action specified in the 24-bit input word. The complete sequence is shown in Figure 2a. The command (C3-C0) and address (A3-A0) assignments are shown in Table 1. The first four commands in the table consist of write and update operations. A write operation loads a 16-bit data word from the 32-bit shift register into the input register of the selected DAC, n. An update operation copies the data word from the input register to the DAC register. Once copied into the DAC register, the data word becomes the active 16-, 14- or 12-bit input code, and is converted to an analog voltage at the DAC output. The update operation also powers up the selected DAC if it had been in power-down mode. The data path and registers are shown in the block diagram. While the minimum input word is 24 bits, it may optionally be extended to 32 bits. To use the 32-bit word width, 8 don't-care bits are transferred to the device first, followed by the 24-bit word as just described. Figure 2b shows the 32-bit sequence. The 32-bit word is required for daisychain operation, and is also available to accommodate 2604fb 10 LTC2604/LTC2614/LTC2624 U OPERATIO INPUT WORD (LTC2604) COMMAND C3 C2 C1 C0 ADDRESS A3 A2 A1 DATA (16 BITS) A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 MSB LSB 2604 TBL01 INPUT WORD (LTC2614) COMMAND C3 C2 C1 C0 ADDRESS A3 A2 A1 DATA (14 BITS + 2 DON'T-CARE BITS) A0 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 MSB X X LSB 2604 TBL02 INPUT WORD (LTC2624) COMMAND C3 C2 C1 C0 ADDRESS A3 A2 A1 DATA (12 BITS + 4 DON'T-CARE BITS) A0 D11 D10 D9 D8 D7 D6 D5 D4 D3 MSB D2 D1 D0 X X X X LSB 2604 TBL03 microprocessors which have a minimum word width of 16 bits (2 bytes). can be controlled by using the no-operation command (1111) for the other devices in the chain. Daisy-Chain Operation Power-Down Mode The serial output of the shift register appears at the SDO pin. Data transferred to the device from the SDI input is delayed 32 SCK rising edges before being output at the next SCK falling edge. For power-constrained applications, power-down mode can be used to reduce the supply current whenever less than four outputs are needed. When in power-down, the buffer amplifiers, bias circuits and reference inputs are disabled, and draw essentially zero current. The DAC outputs are put into a high-impedance state, and the output pins are passively pulled to ground through individual 90k resistors. Input- and DAC-register contents are not disturbed during power-down. The SDO output can be used to facilitate control of multiple serial devices from a single 3-wire serial port (i.e., SCK, SDI and CS/LD). Such a "daisy-chain" series is configured by connecting SDO of each upstream device to SDI of the next device in the chain. The shift registers of the devices are thus connected in series, effectively forming a single input shift register which extends through the entire chain. Because of this, the devices can be addressed and controlled individually by simply concatenating their input words; the first instruction addresses the last device in the chain and so forth. The SCK and CS/LD signals are common to all devices in the series. In use, CS/LD is first taken low. Then the concatenated input data is transferred to the chain, using SDI of the first device as the data input. When the data transfer is complete, CS/LD is taken high, completing the instruction sequence for all devices simultaneously. A single device Any channel or combination of channels can be put into power-down mode by using command 0100b in combination with the appropriate DAC address, (n). The 16-bit data word is ignored. The supply current is reduced by approximately 1/4 for each DAC powered down. The effective resistance at REF x (pins 3, 6, 12 and 15) are at highimpedance input (typically > 1G) when the corresponding DACs are powered down. Normal operation can be resumed by executing any command which includes a DAC update, as shown in Table 1. The selected DAC is powered up as its voltage output is updated. When a DAC which is in a powered-down state is 2604fb 11 LTC2604/LTC2614/LTC2624 U OPERATIO powered up and updated, normal settling is delayed. If less than four DACs are in a powered-down state prior to the update command, the power-up delay time is 5s. If on the other hand, all four DACs are powered down, then the main bias generation circuit block has been automatically shut down in addition to the individual DAC amplifiers and reference inputs. In this case, the power up delay time is 12s (for VCC = 5V) or 30s (for VCC = 3V). Voltage Outputs Each of the four rail-to-rail amplifiers contained in these parts has guaranteed load regulation when sourcing or sinking up to 15mA at 5V (7.5mA at 3V). Load regulation is a measure of the amplifier's ability to maintain the rated voltage accuracy over a wide range of load conditions. The measured change in output voltage per milliampere of forced load current change is expressed in LSB/mA. DC output impedance is equivalent to load regulation, and may be derived from it by simply calculating a change in units from LSB/mA to Ohms. The amplifiers' DC output impedance is 0.025 when driving a load well away from the rails. When drawing a load current from either rail, the output voltage headroom with respect to that rail is limited by the 30 typical channel resistance of the output devices; e.g., when sinking 1mA, the minimum output voltage = 30 * 1mA = 25mV. See the graph Headroom at Rails vs Output Current in the Typical Performance Characteristics section. The amplifiers are stable driving capacitive loads of up to 1000pF. Board Layout The excellent load regulation and DC crosstalk performance of these devices is achieved in part by keeping "signal" and "power" grounds separate. The PC board should have separate areas for the analog and digital sections of the circuit. This keeps digital signals away from sensitive analog signals and facilitates the use of separate digital and analog ground planes which have minimal capacitive and resistive interaction with each other. Digital and analog ground planes should be joined at only one point, establishing a system star ground as close to the device's ground pin as possible. Ideally, the analog ground plane should be located on the component side of the board, and should be allowed to run under the part to shield it from noise. Analog ground should be a continuous and uninterrupted plane, except for necessary lead pads and vias, with signal traces on another layer. The GND pin functions as a return path for power supply currents in the device and should be connected to analog ground. Resistance from the GND pin to system star ground should be as low as possible. When a zero scale DAC output voltage of zero is desired, the REFLO pin (pin 2) should be connected to system star ground. Rail-to-Rail Output Considerations In any rail-to-rail voltage output device, the output is limited to voltages within the supply range. Since the analog outputs of the device cannot go below ground, they may limit for the lowest codes as shown in Figure 3b. Similarly, limiting can occur near full scale when the REF pins are tied to VCC. If REF x = VCC and the DAC full-scale error (FSE) is positive, the output for the highest codes limits at VCC as shown in Figure 3c. No fullscale limiting can occur if REF x is less than VCC - FSE. Offset and linearity are defined and tested over the region of the DAC transfer function where no output limiting can occur. 2604fb 12 X X SDI SDO SCK CS/LD 1 X X 2 X X 3 X 4 5 X X DON'T CARE X C3 SDI C2 2 C1 3 X X 6 X X 7 COMMAND WORD 1 SCK CS/LD X X C0 8 4 A2 6 A1 7 C2 10 C1 11 D15 9 D14 10 D12 12 D11 13 D10 14 24-BIT INPUT WORD D13 11 D9 15 D7 17 DATA WORD D8 16 D6 18 D5 19 C1 C0 C0 A3 A3 A2 14 A1 15 A2 A1 ADDRESS WORD 13 A0 A0 16 17 D15 D15 PREVIOUS 32-BIT INPUT WORD 12 D14 D14 18 SDO SDI SCK D13 D13 19 D12 D12 20 t3 17 D10 D10 22 t2 t8 D9 D9 t4 23 PREVIOUS D15 D15 t1 D11 D11 21 D8 24 D4 20 D7 25 D3 21 18 D7 PREVIOUS D14 D14 D8 DATA WORD Figure 2b. LTC2604 32-Bit Load Sequence LTC2614 SDI/SDO Data Word: 14-Bit Input Code + 2 Don't Care Bits LTC2624 SDI/SDO Data Word: 12-Bit Input Code + 4 Don't Care Bits C2 COMMAND WORD 9 C3 A0 8 Figure 2a. LTC2604 24-Bit Load Sequence (Minimum Input Word) LTC2614 SDI Data Word: 14-Bit Input Code + 2 Don't Care Bits LTC2624 SDI Data Word: 12-Bit Input Code + 4 Don't Care Bits ADDRESS WORD C3 A3 5 D6 D6 26 D2 22 D5 D5 27 D1 23 D4 D4 28 D0 24 D3 D3 29 2604 F02a D2 D2 30 D1 D1 31 2604 F02b CURRENT 32-BIT INPUT WORD D0 D0 32 LTC2604/LTC2614/LTC2624 U OPERATIO 2604fb 13 LTC2604/LTC2614/LTC2624 U OPERATIO VREF = VCC VREF = VCC POSITIVE FSE OUTPUT VOLTAGE OUTPUT VOLTAGE INPUT CODE OUTPUT VOLTAGE (c) 0 32,768 INPUT CODE 65,535 0V NEGATIVE OFFSET INPUT CODE (a) 2600 F03 (b) Figure 3. Effects of Rail-to-Rail Operation On a DAC Transfer Curve. (a) Overall Transfer Function (b) Effect of Negative Offset for Codes Near Zero Scale (c) Effect of Positive Full-Scale Error for Codes Near Full Scale 2604fb 14 LTC2604/LTC2614/LTC2624 U PACKAGE DESCRIPTIO GN Package 16-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .189 - .196* (4.801 - 4.978) .045 .005 16 15 14 13 12 11 10 9 .254 MIN .009 (0.229) REF .150 - .165 .229 - .244 (5.817 - 6.198) .0165 .0015 .150 - .157** (3.810 - 3.988) .0250 BSC RECOMMENDED SOLDER PAD LAYOUT 1 .015 .004 x 45 (0.38 0.10) .007 - .0098 (0.178 - 0.249) 2 3 4 5 6 7 .0532 - .0688 (1.35 - 1.75) 8 .004 - .0098 (0.102 - 0.249) 0 - 8 TYP .016 - .050 (0.406 - 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 - .012 (0.203 - 0.305) TYP .0250 (0.635) BSC GN16 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 2604fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC2604/LTC2614/LTC2624 U TYPICAL APPLICATIO 5V 5V 1k 1k 10k 10k 0.1F 0.1F 10k 10k 0.01F 20 49.9 70MHz IN 47pF ZC830 0.01F OUT 10pF 49.9 20pF 49.9 ZC830 DAC A DAC B DAC C DAC D OPTIONAL OPTIONAL 20k 0.1F 20k CS/LD SCK SDI 0.1F LTC2604 5V 5V LO 2.74k 1% 2.74k 1% 100k 100k 2.74k 1% 90 2.74k 1% I+Q MODULATOR Q INPUT I INPUT 5V 5V 2.74k 1% 0 2.74k 1% RF *ZETEX 2.74k 1% 2.74k 1% 2604 F04 (516) 543-7100 Figure 4. Using DAC A and DAC B for Nearly Continuous Attenuation Control and DAC C and DAC D to Trim for Minimum LO Feedthrough in a Mixer. RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1458/LTC1458L Quad 12-Bit Rail-to-Rail Output DACs with Added Functionality LTC1654 LTC1655/LTC1655L LTC1657/LTC1657L LTC1660/LTC1665 LTC1821 LTC2600/LTC2610/LTC2620 LTC2602/LTC2612/LTC2622 Dual 14-Bit Rail-to-Rail VOUT DAC Single 16-Bit VOUT DAC with Serial Interface in SO-8 Parallel 5V/3V 16-Bit VOUT DAC Octal 8/10-Bit VOUT DAC in 16-Pin Narrow SSOP Parallel 16-Bit Voltage Output DAC Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP Dual 16-/14-/12-Bit Rail-to-Rail DACs in 8-Lead MSOP LTC1458: VCC = 4.5V to 5.5V, VOUT = 0V to 4.096V LTC1458L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V Programmable Speed/Power VCC = 5V(3V), Low Power, Deglitched Low Power, Deglitched, Rail-to-Rail VOUT VCC = 2.7V to 5.5V, Micropower, Rail-to-Rail Output Precision 16-Bit Settling in 2s for 10V Step 250A per DAC, 2.5V to 5.5V Supply Range 300A per DAC, 2.5V to 5.5V Supply Range 2604fb 16 Linear Technology Corporation LT 0407 REV B * PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2004