Freescale Semiconductor Data Sheet Document Number: MSC7116 Rev. 13, 4/2008 MSC7116 Low-Cost 16-bit DSP with DDR Controller and 10/100 Mbps Ethernet MAC * StarCore(R) SC1400 DSP extended core with one SC1400 DSP core, 192 Kbyte of internal SRAM M1 memory, 16 way 16 Kbyte instruction cache (ICache), four-entry write buffer, programmable interrupt controller (PIC), and low-power Wait and Stop processing modes. * 192 Kbyte M2 memory for critical data and temporary data buffering. * 8 Kbyte boot ROM. * AHB-Lite crossbar switch that allows parallel data transfers between four master ports and six slave ports, where each port connects to an AHB-Lite bus; fixed or round robin priority programmable at each slave port; programmable bus parking at each slave port; low power mode. * Internal PLL generates up to 266 MHz clock for the SC1400 core and up to 133 MHz for the crossbar switch, DMA channels, M2 memory, and other peripherals. * Clock synthesis module provides predivision of PLL input clock; independent clocking of the internal timers and DDR module; programmable operation in the SC1400 low power Stop mode; independent shutdown of different regions of the device. * Enhanced 16-bit wide host interface (HDI16) provides a glueless connection to industry-standard microcomputers, microprocessors, and DSPs and can also operate with an 8-bit host data bus, making if fully compatible with the DSP56300 HI08 from the external host side. * DDR memory controller that supports byte enables for up to a 32-bit data bus; glueless interface to 133 MHz 14-bit page mode DDR-RAM; 14-bit external address bus supporting up to 1 Gbyte; and 16-bit or 32-bit external data bus. * Programmable memory interface with independent read buffers, programmable predictive read feature for each buffer, and a write buffer. * System control unit performs software watchdog timer function; includes programmable bus time-out monitors on AHB-Lite slave buses; includes bus error detection and programmable time-out monitors on AHB-Lite master buses; and has address out-of-range detection on each crossbar switch buses. * Event port collects and counts important signal events including DMA and interrupt requests and trigger events such as interrupts, breakpoints, DMA transfers, or wake-up events; units operate independently, in sequence, or triggered externally; can be used standalone or with the OCE10. MAP-BGA-400 17 mm x 17 mm * Multi-channel DMA controller with 32 time-multiplexed unidirectional channels, priority-based time-multiplexing between channels using 32 internal priority levels, fixed- or round-robin-priority operation, major-minor loop structure, and DONE or DRACK protocol from requesting units. * Two independent TDM modules with independent receive and transmit, programmable sharing of frame sync and clock, programmable word size (8 or 16-bit), hardware-base A-law/-law conversion, up to 50 Mbps data rate per TDM, up to 128 channels, with glueless interface to E1/T1 frames and MVIP, SCAS, and H.110 buses. * Ethernet controller with support for 10/100 Mbps MII/RMII designed to comply with IEEE Std. 802.3TM, 802.3uTM, 802.3xTM, and 802.3acTM; with internal receive and transmit FIFOs and a FIFO controller; direct access to internal memories via its own DMA controller; full and half duplex operation; programmable maximum frame length; virtual local area network (VLAN) tag and priority support; retransmission of transmit FIFO following collision; CRC generation and verification for inbound and outbound packets; and address recognition including promiscuous, broadcast, individual address. hash/exact match, and multicast hash match. * UART with full-duplex operation up to 5.0 Mbps. * Up to 41 general-purpose input/output (GPIO) ports. * I2C interface that allows booting from EEPROM devices up to 1 Mbyte. * Two quad timer modules, each with sixteen configurable 16-bit timers. * fieldBISTTM unit detects and provides visibility into unlikely field failures for systems with high availability to ensure structural integrity, that the device operates at the rated speed, is free from reliability defects, and reports diagnostics for partial or complete device inoperability. * Standard JTAG interface allows easy integration to system firmware and internal on-chip emulation (OCE10) module. * Optional booting external host via 8-bit or 16-bit access through the HDI16, I2C, or SPI using in the boot ROM to access serial SPI Flash/EEPROM devices; different clocking options during boot with the PLL on or off using a variety of input frequency ranges. (c) Freescale Semiconductor, Inc., 2004, 2008. All rights reserved. Table of Contents 1 2 3 4 5 6 7 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.1 MAP-BGA Ball Layout Diagrams . . . . . . . . . . . . . . . . . .4 1.2 Signal List By Ball Location. . . . . . . . . . . . . . . . . . . . . . .6 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 2.1 Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 2.2 Recommended Operating Conditions. . . . . . . . . . . . . .18 2.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . .19 2.4 DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . .19 2.5 AC Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Hardware Design Considerations . . . . . . . . . . . . . . . . . . . . . .41 3.1 Thermal Design Considerations . . . . . . . . . . . . . . . . . .41 3.2 Power Supply Design Considerations. . . . . . . . . . . . . .42 3.3 Estimated Power Usage Calculations. . . . . . . . . . . . . .49 3.4 Reset and Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 3.5 DDR Memory System Guidelines . . . . . . . . . . . . . . . . .54 Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Package Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. MSC7116 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . 3 MSC7116 Molded Array Process-Ball Grid Array (MAP-BGA), Top View . . . . . . . . . . . . . . . . . . . . . . . . . 4 MSC7116 Molded Array Process-Ball Grid Array (MAP-BGA), Bottom View . . . . . . . . . . . . . . . . . . . . . . 5 Timing Diagram for a Reset Configuration Write . . . . 25 DDR DRAM Input Timing Diagram . . . . . . . . . . . . . . 26 DDR DRAM Output Timing Diagram . . . . . . . . . . . . . 27 DDR DRAM AC Test Load. . . . . . . . . . . . . . . . . . . . . 28 Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. TDM Receive Signals. . . . . . . . . . . . . . . . . . . . . . . . . TDM Transmit Signals . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Receive Signal Timing . . . . . . . . . . . . . . . . . Ethernet Receive Signal Timing . . . . . . . . . . . . . . . . . Asynchronous Input Signal Timing . . . . . . . . . . . . . . . Serial Management Channel Timing . . . . . . . . . . . . . Read Timing Diagram, Single Data Strobe . . . . . . . . Read Timing Diagram, Double Data Strobe . . . . . . . . Write Timing Diagram, Single Data Strobe. . . . . . . . . Write Timing Diagram, Double Data Strobe . . . . . . . . Host DMA Read Timing Diagram, HPCR[OAD] = 0 . . Host DMA Write Timing Diagram, HPCR[OAD] = 0 . . I2C Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . UART Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . UART Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . EE Pin Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EVNT Pin Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . GPI/GPO Pin Timing . . . . . . . . . . . . . . . . . . . . . . . . . Test Clock Input Timing Diagram . . . . . . . . . . . . . . . . Boundary Scan (JTAG) Timing Diagram . . . . . . . . . . Test Access Port Timing Diagram . . . . . . . . . . . . . . . TRST Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . Voltage Sequencing Case 1 . . . . . . . . . . . . . . . . . . . . Voltage Sequencing Case 2 . . . . . . . . . . . . . . . . . . . . Voltage Sequencing Case 3 . . . . . . . . . . . . . . . . . . . . Voltage Sequencing Case 4 . . . . . . . . . . . . . . . . . . . . Voltage Sequencing Case 5 . . . . . . . . . . . . . . . . . . . . PLL Power Supply Filter Circuits . . . . . . . . . . . . . . . . SSTL Termination Techniques . . . . . . . . . . . . . . . . . . SSTL Power Value . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 29 29 30 30 31 33 33 34 34 35 35 36 37 37 37 38 38 39 40 40 40 43 44 45 46 47 48 54 55 MSC7116 Data Sheet, Rev. 13 2 Freescale Semiconductor JTAG DMA (32 Channel) AMDMA 128 64 OCE10 to IPBus SC1400 Core Trace Buffer (8 KB) 64 M2 SRAM (192 KB) 128 Boot ROM (8 KB) 128 ASM2 MUX JTAG Port 64 DSP Extended Core ASEMI 64 External Memory Interface from IPBus External Bus 128 M1 SRAM (192 KB) 64 128 AMEC 64 32 HDI16 Port TDM 32 2 TDMs PLL/Clock I2C APB UART PLL/Clock I2C RS-232 GPIO 64 AMENT Ethernet MAC Note: The arrows show the direction of the transfer. ASAPB Host Interface (HDI16) ASM1 64 64 P XA XB 64 ASIB 32 IB Bridge Extended Core Interface AMIC ASTH MUX Instruction Cache (16 KB) APB Bridge AHB-Lite Crossbar Switch Interrupt Control Fetch Unit 32 Interrupts GPIO System Ctrl 32 to EMI to DMA MII/RMII Watchdog Event Port BTMs Events to/from OCE10 Timers IPBus Figure 1. MSC7116 Block Diagram MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 3 Pin Assignments 1 Pin Assignments This section includes diagrams of the MSC7116 package ball grid array layouts and pinout allocation tables. 1.1 MAP-BGA Ball Layout Diagrams Top and bottom views of the MAP-BGA package are shown in Figure 2 and Figure 3 with their ball location index numbers. Top View 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A GND GND DQM1 DQS2 CK CK HD15 HD12 HD10 HD7 HD6 HD4 HD1 HD0 GND BM3 NC NC NC NC B VDDM NC CS0 DQM2 DQS3 DQS0 CKE WE HD14 HD11 HD8 HD5 HD2 NC BM2 NC NC NC NC NC C D24 D30 D25 CS1 DQM3 DQM0 DQS1 RAS CAS HD13 HD9 HD3 NC NC NC NC NC NC NC NC D VDDM D28 D27 GND VDDM VDDM VDDM VDDM VDDM VDDM VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDC NC NC NC E GND D26 D31 VDDM VDDM VDDC VDDC VDDC VDDC VDDM VDDIO VDDIO VDDIO VDDIO VDDIO VDDC VDDC NC NC NC F VDDM D15 D29 VDDC VDDC VDDC GND GND GND VDDM VDDM GND GND GND VDDIO VDDC VDDC NC NC NC G GND D13 GND VDDM VDDM GND GND GND GND GND GND GND GND GND VDDIO VDDIO VDDC NC NC NC H D14 D12 D11 VDDM VDDM GND GND GND GND GND GND GND GND GND VDDIO VDDIO VDDC NC HA2 HA1 J D10 VDDM D9 VDDM VDDM VDDM GND GND GND GND GND GND GND GND GND VDDIO VDDC HA3 HACK HREQ K D0 GND D8 VDDC VDDM GND GND GND GND GND GND GND GND GND VDDIO VDDIO VDDC HA0 HDDS HDS L D1 GND D3 VDDC VDDM GND GND GND GND GND GND GND GND VDDIO VDDIO VDDIO VDDC HCS2 HCS1 HRW M D2 VDDM D5 VDDM VDDM GND GND GND GND GND GND GND GND GND GND VDDC VDDC SDA UTXD URXD N D4 D6 VREF VDDM VDDM VDDM GND GND GND GND GND GND GND GND VDDIO VDDC VDDC CLKIN SCL VSSPLL P D7 D17 D16 VDDM VDDM VDDM GND GND GND GND GND GND GND GND VDDIO VDDIO VDDC PORESET TPSEL VDDPLL R GND D19 D18 VDDM VDDM VDDM GND VDDM GND VDDM GND GND VDDIO GND VDDIO VDDIO VDDC TDO EE0 TEST0 T VDDM D20 D22 VDDM VDDM VDDC VDDM VDDM VDDC VDDM VDDM VDDIO VDDIO VDDIO VDDIO VDDC VDDC MDIO TMS HRESET U GND D21 D23 VDDM VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC COL TCK TRST V VDDM NC A13 A11 A10 A5 A2 BA0 NC T1TD TX_ER RXD2 RXD0 TX_EN CRS TDI W GND VDDM A12 A8 A7 A6 A3 NC EVNT1 EVNT2 T0RFS T0TFS T1TFS TXD2 RXD3 TXD1 TXCLK RX_ER Y VDDM GND A9 A1 A0 A4 BA1 NMI EVNT3 T0RCK T1RCK T1TCK TXD3 RXCLK TXD0 RXD1 EVNT0 EVNT4 T0TCK T1RFS T0RD TOTD T1RD GND MDC RX_DV Figure 2. MSC7116 Molded Array Process-Ball Grid Array (MAP-BGA), Top View MSC7116 Data Sheet, Rev. 13 4 Freescale Semiconductor Pin Assignments Bottom View 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A NC NC NC NC BM3 GND HD0 HD1 HD4 HD6 HD7 HD10 HD12 HD15 CK CK DQS2 DQM1 GND GND B NC NC NC NC NC BM2 NC HD2 HD5 HD8 HD11 HD14 WE CKE DQS0 DQS3 DQM2 CS0 NC VDDM C NC NC NC NC NC NC NC NC HD3 HD9 HD13 CAS RAS DQS1 DQM0 DQM3 CS1 D25 D30 D24 D NC NC NC VDD VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDM VDDM VDDM VDDM VDDM VDDM GND D27 D28 VDDM E NC NC NC VDD VDD VDDIO VDDIO VDDIO VDDIO VDDIO VDDM VDD VDD VDD VDD VDDM VDDM D31 D26 GND F NC NC NC VDD VDD VDDIO GND GND GND VDDM VDDM GND GND GND VDD VDD VDD D29 D15 VDDM G NC NC NC VDD VDDIO VDDIO GND GND GND GND GND GND GND GND GND VDDM VDDM GND D13 GND H HA1 HA2 NC VDD VDDIO VDDIO GND GND GND GND GND GND GND GND GND VDDM VDDM D11 D12 D14 J HREQ HACK HA3 VDD VDDIO GND GND GND GND GND GND GND GND GND VDDM VDDM VDDM D9 VDDM D10 K HDS HDDS HA0 VDD VDDIO VDDIO GND GND GND GND GND GND GND GND GND VDDM VDD D8 GND D0 L HRW HCS1 HCS2 VDD VDDIO VDDIO VDDIO GND GND GND GND GND GND GND GND VDDM VDD D3 GND D1 M URXD UTXD SDA VDD VDD GND GND GND GND GND GND GND GND GND GND VDDM VDDM D5 VDDM D2 N VSSPLL SCL CLKIN VDD VDD VDDIO GND GND GND GND GND GND GND GND VDDM VDDM VDDM VREF D6 D4 P VDDPLL TPSEL PORESET VDD VDDIO VDDIO GND GND GND GND GND GND GND GND VDDM VDDM VDDM D16 D17 D7 R TEST0 EE0 TDO VDD VDDIO VDDIO GND VDDIO GND GND VDDM GND VDDM GND VDDM VDDM VDDM D18 D19 GND T HRESET TMS MDIO VDD VDD VDDIO VDDIO VDDIO VDDIO VDDM VDDM VDD VDDM VDDM VDD VDDM VDDM D22 D20 VDDM U TRST TCK COL VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDD VDDM D23 D21 GND V TDI CRS TX_EN RXD0 RXD2 TX_ER T1TD T1RFS T0TCK EVNT4 EVNT0 NC BA0 A2 A5 A10 A11 A13 NC VDDM W MDC RX_ER TXCLK TXD1 RXD3 TXD2 T1TFS T1RD T0TFS T0RFS EVNT2 EVNT1 NC A3 A6 A7 A8 A12 VDDM GND Y RX_DV TXD0 RXCLK TXD3 T1TCK T1RCK TOTD NMI BA1 A4 A0 A1 A9 GND VDDM GND RXD1 T0RD T0RCK EVNT3 Figure 3. MSC7116 Molded Array Process-Ball Grid Array (MAP-BGA), Bottom View MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 5 Pin Assignments 1.2 Signal List By Ball Location Table 1 lists the signals sorted by ball number and configuration. Table 1. MSC7116 Signals by Ball Designator Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled A1 GND A2 GND A3 DQM1 A4 DQS2 A5 CK A6 CK Primary Alternate A7 GPIC7 GPOC7 HD15 A8 GPIC4 GPOC4 HD12 A9 GPIC2 GPOC2 HD10 A10 reserved HD7 A11 reserved HD6 A12 reserved HD4 A13 reserved HD1 A14 reserved HD0 A15 A16 GND BM3 GPID8 A17 NC A18 NC A19 NC A20 NC B1 VDDM B2 NC B3 CS0 B4 DQM2 B5 DQS3 B6 DQS0 B7 CKE B8 WE GPOD8 reserved B9 GPIC6 GPOC6 HD14 B10 GPIC3 GPOC3 HD11 B11 GPIC0 GPOC0 HD8 B12 reserved HD5 B13 reserved HD2 MSC7116 Data Sheet, Rev. 13 6 Freescale Semiconductor Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) B14 B15 Interrupt Enabled Hardware Controlled GPO Enabled Primary Alternate NC BM2 GPID7 B16 NC B17 NC B18 NC B19 NC B20 NC C1 D24 C2 D30 C3 D25 C4 CS1 C5 DQM3 C6 DQM0 C7 DQS1 C8 RAS C9 CAS GPOD7 reserved C10 GPIC5 GPOC5 HD13 C11 GPIC1 GPOC1 HD9 C12 reserved HD3 C13 NC C14 NC C15 NC C16 NC C17 NC C18 NC C19 NC C20 NC D1 VDDM D2 D28 D3 D27 D4 GND D5 VDDM D6 VDDM D7 VDDM D8 VDDM D9 VDDM MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 7 Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled D10 VDDM D11 VDDIO D12 VDDIO D13 VDDIO D14 VDDIO D15 VDDIO D16 VDDIO D17 VDDC D18 NC D19 NC D20 NC E1 GND E2 D26 E3 D31 E4 VDDM E5 VDDM E6 VDDC E7 VDDC E8 VDDC E9 VDDC E10 VDDM E11 VDDIO E12 VDDIO E13 VDDIO E14 VDDIO E15 VDDIO E16 VDDC E17 VDDC E18 NC E19 NC E20 NC F1 VDDM F2 D15 F3 D29 F4 VDDC F5 VDDC Primary Alternate MSC7116 Data Sheet, Rev. 13 8 Freescale Semiconductor Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled F6 VDDC F7 GND F8 GND F9 GND F10 VDDM F11 VDDM F12 GND F13 GND F14 GND F15 VDDIO F16 VDDC F17 VDDC F18 NC F19 NC F20 NC G1 GND G2 D13 G3 GND G4 VDDM G5 VDDM G6 GND G7 GND G8 GND G9 GND G10 GND G11 GND G12 GND G13 GND G14 GND G15 VDDIO G16 VDDIO G17 VDDC G18 NC G19 NC G20 NC H1 D14 Primary Alternate MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 9 Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled H2 D12 H3 D11 H4 VDDM H5 VDDM H6 GND H7 GND H8 GND H9 GND H10 GND H11 GND H12 GND H13 GND H14 GND H15 VDDIO H16 VDDIO H17 VDDC H18 NC Primary Alternate H19 reserved HA2 H20 reserved HA1 J1 D10 J2 VDDM J3 D9 J4 VDDM J5 VDDM J6 VDDM J7 GND J8 GND J9 GND J10 GND J11 GND J12 GND J13 GND J14 GND J15 GND J16 VDDIO J17 VDDC MSC7116 Data Sheet, Rev. 13 10 Freescale Semiconductor Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset J18 Interrupt Enabled GPO Enabled GPIC11 J19 J20 GPI Enabled (Default) Hardware Controlled GPOC11 Alternate HA3 HACK/HACK or HRRQ/HRRQ reserved HDSP Primary HREQ/HREQ or HTRQ/HTRQ reserved K1 D0 K2 GND K3 D8 K4 VDDC K5 VDDM K6 GND K7 GND K8 GND K9 GND K10 GND K11 GND K12 GND K13 GND K14 GND K15 VDDIO K16 VDDIO K17 VDDC K18 reserved HA0 K19 reserved HDDS K20 reserved HDS/HDS or HWR/HWR L1 D1 L2 GND L3 D3 L4 VDDC L5 VDDM L6 GND L7 GND L8 GND L9 GND L10 GND L11 GND L12 GND L13 GND MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 11 Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled L14 VDDIO L15 VDDIO L16 VDDIO L17 VDDC L18 GPIB11 GPOB11 Primary Alternate HCS2/HCS2 L19 reserved HCS1/HCS1 L20 reserved HRW or HRD/HRD M1 D2 M2 VDDM M3 D5 M4 VDDM M5 VDDM M6 GND M7 GND M8 GND M9 GND M10 GND M11 GND M12 GND M13 GND M14 GND M15 GND M16 VDDC M17 VDDC M18 GPIA14 IRQ15 GPOA14 SDA M19 GPIA12 IRQ3 GPOA12 UTXD M20 GPIA13 IRQ2 GPOA13 URXD N1 D4 N2 D6 N3 VREF N4 VDDM N5 VDDM N6 VDDM N7 GND N8 GND N9 GND MSC7116 Data Sheet, Rev. 13 12 Freescale Semiconductor Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled N10 GND N11 GND N12 GND N13 GND N14 GND N15 VDDIO N16 VDDC N17 VDDC N18 CLKIN N19 GPIA15 IRQ14 GPOA15 N20 VSSPLL P1 D7 P2 D17 P3 D16 P4 VDDM P5 VDDM P6 VDDM P7 GND P8 GND P9 GND P10 GND P11 GND P12 GND P13 GND P14 GND P15 VDDIO P16 VDDIO P17 VDDC P18 PORESET P19 TPSEL P20 VDDPLL R1 GND R2 D19 R3 D18 R4 VDDM R5 VDDM Primary Alternate SCL MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 13 Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled R6 VDDM R7 GND R8 VDDM R9 GND R10 VDDM R11 GND R12 GND R13 VDDIO R14 GND R15 VDDIO R16 VDDIO R17 VDDC R18 TDO R19 reserved Alternate EE0/DBREQ R20 TEST0 T1 VDDM T2 D20 T3 D22 T4 VDDM T5 VDDM T6 VDDC T7 VDDM T8 VDDM T9 VDDC T10 VDDM T11 VDDM T12 VDDIO T13 VDDIO T14 VDDIO T15 VDDIO T16 VDDC T17 VDDC T18 Primary reserved MDIO T19 TMS T20 HRESET U1 GND MSC7116 Data Sheet, Rev. 13 14 Freescale Semiconductor Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled Hardware Controlled GPO Enabled U2 D21 U3 D23 U4 VDDM U5 VDDC U6 VDDC U7 VDDC U8 VDDC U9 VDDC U10 VDDC U11 VDDC U12 VDDC U13 VDDC U14 VDDC U15 VDDC U16 VDDC U17 VDDC U18 reserved TCK U20 TRST V1 VDDM V2 NC V3 A13 V4 A11 V5 A10 V6 A5 V7 A2 V8 BA0 V9 NC V10 reserved SWTE GPIA16 Alternate COL U19 V11 Primary EVNT0 IRQ12 GPOA16 EVNT4 V12 GPIA8 IRQ6 GPOA8 T0TCK V13 GPIA4 IRQ1 GPOA4 T1RFS V14 GPIA0 IRQ11 GPOA0 T1TD V15 GPIA28 IRQ17 GPOA28 TX_ER reserved GPOD6 RXD2 reserved V16 V17 GPID6 GPIA22 IRQ22 GPOA22 RXD0 MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 15 Pin Assignments Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset V18 GPI Enabled (Default) GPIA24 V19 Hardware Controlled Interrupt Enabled GPO Enabled IRQ24 GPOA24 CRS TDI W1 GND W2 VDDM W3 A12 W4 A8 W5 A7 W6 A6 W7 A3 W8 NC W9 GPIA17 GPOA17 IRQ13 BM0 Alternate TX_EN reserved V20 W10 Primary GPIC14 EVNT1 CLKO GPOC14 EVNT2 W11 GPIA10 IRQ5 GPOA10 T0RFS W12 GPIA7 IRQ7 GPOA7 T0TFS W13 GPIA3 IRQ8 GPOA3 T1RD W14 GPIA1 IRQ10 GPOA1 T1TFS W15 GPID4 GPOD4 TXD2 reserved RXD3 reserved W16 GPIA27 IRQ18 GPOA27 W17 GPIA19 IRQ19 GPOA19 TXD1 W18 GPIA23 IRQ23 GPOA23 TXCLK or REFCLK W19 GPIA26 IRQ26 GPOA26 RX_ER W20 H8BIT reserved MDC Y1 VDDM Y2 GND Y3 A9 Y4 A1 Y5 A0 Y6 A4 Y7 BA1 Y8 Y9 Y10 reserved reserved NMI BM1 GPIC15 GPIA11 IRQ4 GPOC15 EVNT3 GPOA11 T0RCK Y11 GPIA9 GPOA9 T0RD Y12 GPIA6 GPOA6 T0TD GPOA5 T1RCK Y13 GPIA5 IRQ0 MSC7116 Data Sheet, Rev. 13 16 Freescale Semiconductor Electrical Characteristics Table 1. MSC7116 Signals by Ball Designator (continued) Signal Names Software Controlled Number End of Reset GPI Enabled (Default) Interrupt Enabled GPO Enabled Primary Alternate Y14 GPIA2 IRQ9 GPOA2 Y15 GPIA29 IRQ16 GPOA29 TXD3 reserved GPOD5 RXCLK reserved Y16 GPID5 T1TCK Y17 GPIA20 IRQ20 GPOA20 TXD0 Y18 GPIA21 IRQ21 GPOA21 RXD1 GPOA25 RX_DV or CRS_DV Y19 GND Y20 2 Hardware Controlled GPIA25 IRQ25 Electrical Characteristics This document contains detailed information on power considerations, DC/AC electrical characteristics, and AC timing specifications. For additional information, see the MSC711x Reference Manual. 2.1 Maximum Ratings CAUTION This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, normal precautions should be taken to avoid exceeding maximum voltage ratings. Reliability is enhanced if unused inputs are tied to an appropriate logic voltage level (for example, either GND or VDD). In calculating timing requirements, adding a maximum value of one specification to a minimum value of another specification does not yield a reasonable sum. A maximum specification is calculated using a worst case variation of process parameter values in one direction. The minimum specification is calculated using the worst case for the same parameters in the opposite direction. Therefore, a "maximum" value for a specification never occurs in the same device with a "minimum" value for another specification; adding a maximum to a minimum represents a condition that can never exist. MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 17 Electrical Characteristics Table 2 describes the maximum electrical ratings for the MSC7116. Table 2. Absolute Maximum Ratings Rating Symbol Value Unit Core supply voltage VDDC 1.5 V Memory supply voltage VDDM 4.0 V PLL supply voltage VDDPLL 1.5 V I/O supply voltage VDDIO -0.2 to 4.0 V VIN (GND - 0.2) to 4.0 V VREF 4.0 V Maximum operating temperature TJ 105 C Minimum operating temperature TA -40 C TSTG -55 to +150 C Input voltage Reference voltage Storage temperature range Notes: 1. 2. 3. 2.2 Functional operating conditions are given in Table 3. Absolute maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond the listed limits may affect device reliability or cause permanent damage. Section 3.1, Thermal Design Considerations includes a formula for computing the chip junction temperature (TJ). Recommended Operating Conditions Table 3 lists recommended operating conditions. Proper device operation outside of these conditions is not guaranteed. Table 3. Recommended Operating Conditions Rating Symbol Value Unit Core supply voltage VDDC 1.14 to 1.26 V Memory supply voltage VDDM 2.38 to 2.63 V PLL supply voltage VDDPLL 1.14 to 1.26 V I/O supply voltage VDDIO 3.14 to 3.47 V Reference voltage VREF 1.19 to 1.31 V TJ TA maximum: 105 minimum: -40 C C Operating temperature range MSC7116 Data Sheet, Rev. 13 18 Freescale Semiconductor Electrical Characteristics 2.3 Thermal Characteristics Table 4 describes thermal characteristics of the MSC7116 for the MAP-BGA package. Table 4. Thermal Characteristics for MAP-BGA Package MAP-BGA 17 Characteristic Symbol x 17 mm5 Natural Convection 200 ft/min (1 m/s) airflow Unit Junction-to-ambient1, 2 RJA 39 31 C/W Junction-to-ambient, four-layer board1, 3 RJA 23 20 C/W Junction-to-board4 RJB 12 C/W Junction-to-case5 RJC 7 C/W Junction-to-package-top6 JT 2 C/W Notes: 1. 2. 3. 4. 5. 6. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal. Per JEDEC JESD51-6 with the board horizontal. Thermal resistance between the die and the printed circuit board per JEDEC JESD 51-8. Board temperature is measured on the top surface of the board near the package. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. Section 3.1, Thermal Design Considerations explains these characteristics in detail. 2.4 DC Electrical Characteristics This section describes the DC electrical characteristics for the MSC7116. Note: The leakage current is measured for nominal voltage values must vary in the same direction (for example, both VDDIO and VDDC vary by +2 percent or both vary by -2 percent). Table 5. DC Electrical Characteristics Characteristic Symbol Min Typical Max Unit VDDC VDDPLL 1.14 1.2 1.26 V VDDM 2.375 2.5 2.625 V VDDIO 3.135 3.3 3.465 V VREF 0.49 x VDDM 1.25 0.51 x VDDM V VTT VREF - 0.04 VREF VREF + 0.04 V VIHCLK 2.4 3.0 3.465 V DRAM interface input high I/O voltage VIHM VREF + 0.28 VDDM VDDM + 0.3 V DRAM interface input low I/O voltage VILM -0.3 GND VREF - 0.18 V IIN -1.0 0.09 1 A IVREF -- -- 5 A Core and PLL voltage DRAM interface I/O voltage1 I/O voltage DRAM interface I/O reference voltage2 DRAM interface I/O termination voltage Input high CLKIN voltage Input leakage current, VIN = VDDIO VREF input leakage current 3 MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 19 Electrical Characteristics Table 5. DC Electrical Characteristics (continued) Characteristic Symbol Min Typical Max Unit IOZ -1.0 0.09 1 A Signal low input current, VIL = 0.4 V IL -1.0 0.09 1 A Signal high input current, VIH = 2.0 V IH -1.0 0.09 1 A Output high voltage, IOH = -2 mA, except open drain pins VOH 2.0 3.0 -- V Output low voltage, IOL= 5 mA VOL -- 0 0.4 V P -- 293.0 -- mW Tri-state (high impedance off state) leakage current, VIN = VDDIO 5 Typical power at 266 MHz Notes: 1. 2. 3. 4. 5. The value of VDDM at the MSC7116 device must remain within 50 mV of VDDM at the DRAM device at all times. VREF must be equal to 50% of VDDM and track VDDM variations as measured at the receiver. Peak-to-peak noise must not exceed 2% of the DC value. VTT is not applied directly to the MSC7116 device. It is the level measured at the far end signal termination. It should be equal to VREF. This rail should track variations in the DC level of VREF. Output leakage for the memory interface is measured with all outputs disabled, 0 V VOUT VDDM. The core power values were measured.using a standard EFR pattern at typical conditions (25C, 300 MHz, 1.2 V core). Table 6 lists the DDR DRAM capacitance. Table 6. DDR DRAM Capacitance Parameter/Condition Symbol Max Unit Input/output capacitance: DQ, DQS CIO 30 pF Delta input/output capacitance: DQ, DQS CDIO 30 pF Note: These values were measured under the following conditions: * VDDM = 2.5 V 0.125 V * f = 1 MHz * TA = 25C * VOUT = VDDM/2 * VOUT (peak to peak) = 0.2 V MSC7116 Data Sheet, Rev. 13 20 Freescale Semiconductor Electrical Characteristics 2.5 AC Timings This section presents timing diagrams and specifications for individual signals and parallel I/O outputs and inputs. All AC timings are based on a 30 pF load, except where noted otherwise, and a 50 transmission line. For any additional pF, use the following equations to compute the delay: -- Standard interface: 2.45 + (0.054 x Cload) ns -- DDR interface: 1.6 + (0.002 x Cload) ns 2.5.1 Clock and Timing Signals The following tables describe clock signal characteristics. Table 6 shows the maximum frequency values for internal (core, reference, and peripherals) and external (CLKO) clocks. You must ensure that maximum frequency values are not exceeded (see Section 2.5.2 for the allowable ranges when using the PLL). Table 6. Maximum Frequencies Characteristic Maximum in MHz Core clock frequency (CLOCK) 266 External output clock frequency (CLKO) 67 Memory clock frequency (CK, CK) 133 TDM clock frequency (TxRCK, TxTCK) 50 Table 7. Clock Frequencies in MHz Characteristic Symbol Min Max CLKIN frequency FCLKIN 10 100 CLOCK frequency FCORE -- 266 CK, CK frequency FCK -- 133 FTDMCK -- 50 CLKO frequency FCKO -- 67 AHB/IPBus/APB clock frequency FBCK -- 133 TDMxRCK, TDMxTCK frequency Note: The rise and fall time of external clocks should be 5 ns maximum Table 8. System Clock Parameters Min Max Unit CLKIN frequency Characteristic 10 100 MHz CLKIN slope -- 5 ns CLKIN frequency jitter (peak-to-peak) -- 1000 ps CLKO frequency jitter (peak-to-peak) -- 133 ps MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 21 Electrical Characteristics 2.5.2 Configuring Clock Frequencies This section describes important requirements for configuring clock frequencies in the MSC7116 device when using the PLL block. To configure the device clocking, you must program four fields in the Clock Control Register (CLKCTL): PLLDVF field. Specifies the PLL division factor (PLLDVF + 1) to divide the input clock frequency FCLKIN. The output of the divider block is the input to the multiplier block. PLLMLTF field. Specifies the PLL multiplication factor (PLLMLTF + 1). The output from the multiplier block is the loop frequency FLOOP. RNG field. Selects the available PLL frequency range for FVCO, either FLOOP when the RNG bit is set (1) or FLOOP/2 when the RNG bit is cleared (0). CKSEL field. Selects FCLKIN, FVCO, or FVCO/2 as the source for the core clock. * * * * There are restrictions on the frequency range permitted at the beginning of the multiplication portion of the PLL that affect the allowable values for the PLLDVF and PLLMLTF fields. The following sections define these restrictions and provide guidelines to configure the device clocking when using the PLL. Refer to the Clock and Power Management chapter in the MSC711x Reference Manual for details on the clock programming model. 2.5.2.1 PLL Multiplier Restrictions There are two restrictions for correct usage of the PLL block: * * The input frequency to the PLL multiplier block (that is, the output of the divider) must be in the range 10-25 MHz. The output frequency of the PLL multiplier must be in the range 266-532 MHz. When programming the PLL for a desired output frequency using the PLLDVF, PLLMLTF, and RNG fields, you must meet these constraints. 2.5.2.2 Input Division Factors and Corresponding CLKIN Frequency Range The value of the PLLDVF field determines the allowable CLKIN frequency range, as shown in Table 9. Table 9. CLKIN Frequency Ranges by Divide Factor Value PLLDVF Field Value Input Divide Factor CLKIN Frequency Range 0x00 1 10 to 25 MHz Input Division by 1 0x01 2 20 to 50 MHz Input Division by 2 Comments 0x02 3 30 to 75 MHz Input Division by 3 0x03 4 40 to 100 MHz Input Division by 4 0x04 5 50 to 100 MHz Input Division by 5 0x05 6 60 to 100 MHz Input Division by 6 0x06 7 70 to 100 MHz Input Division by 7 0x07 8 80 to 100 MHz Input Division by 8 0x08 9 90 to 100 MHz Input Division by 9 0x09 10 100 MHz Input Division by 10 Note: The maximum CLKIN frequency is 100 MHz. Therefore, the PLLDVF value must be in the range from 1-10. MSC7116 Data Sheet, Rev. 13 22 Freescale Semiconductor Electrical Characteristics 2.5.2.3 Multiplication Factor Range The multiplier block output frequency ranges depend on the divided input clock frequency as shown in Table 10. Table 10. PLLMLTF Ranges Multiplier Block (Loop) Output Range 266 [Divided Input Clock x (PLLMLTF + 1)] 532 MHz Note: Minimum PLLMLTF Value Maximum PLLMLTF Value 266/Divided Input Clock 532/Divided Input Clock This table results from the allowed range for FLoop. The minimum and maximum multiplication factors are dependent on the frequency of the Divided Input Clock. 2.5.2.4 Allowed Core Clock Frequency Range The frequency delivered to the core, extended core, and peripherals depends on the value of the CLKCTRL[RNG] bit as shown in Table 11. Table 11. Fvco Frequency Ranges CLKCTRL[RNG] Value Allowed Range of Fvco 1 266 Fvco 532 MHz 0 133 Fvco 266 MHz Note: This table results from the allowed range for Fvco, which is FLoop modified by CLKCTRL[RNG]. This bit along with the CKSEL determines the frequency range of the core clock. Table 12. Resulting Ranges Permitted for the Core Clock CLKCTRL[CKSEL] CLKCTRL[RNG] Resulting Division Factor Allowed Range of Core Clock 11 1 1 Reserved 11 0 2 133 core clock 266 MHz Limited by range of PLL 01 1 2 133 core clock 266 MHz Limited by range of PLL 01 0 4 66.5 core clock 133 MHz Limited by range of PLL Note: Comments Reserved This table results from the allowed range for FOUT, which depends on clock selected via CLKCTRL[CKSEL]. 2.5.2.5 Core Clock Frequency Range When Using DDR Memory The core clock can also be limited by the frequency range of the DDR devices in the system. Table 13 summarizes this restriction. Table 13. Core Clock Ranges When Using DDR DDR Type Allowed Frequency Range for DDR CK Corresponding Range for the Core Clock DDR 200 (PC-1600) 83-100 MHz 166 core clock 200 MHz Core limited to 2 x maximum DDR frequency DDR 266 (PC-2100) DDR 333 (PC-2600) 83-133 MHz 166 core clock 266 MHz Core limited to 2 x maximum DDR frequency Comments MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 23 Electrical Characteristics 2.5.3 Reset Timing The MSC7116 device has several inputs to the reset logic. All MSC7116 reset sources are fed into the reset controller, which takes different actions depending on the source of the reset. The reset status register indicates the most recent sources to cause a reset. Table 14 describes the reset sources. Table 14. Reset Sources Name Direction Description Power-on reset (PORESET) Input Initiates the power-on reset flow that resets the MSC7116 and configures various attributes of the MSC7116. On PORESET, the entire MSC7116 device is reset. SPLL and DLL states are reset, HRESET is driven, the SC1400 extended core is reset, and system configuration is sampled. The system is configured only when PORESET is asserted. External Hard reset (HRESET) Input/ Output Initiates the hard reset flow that configures various attributes of the MSC7116. While HRESET is asserted, HRESET is an open-drain output. Upon hard reset, HRESET is driven and the SC1400 extended core is reset. Software watchdog reset Internal When the MSC7116 watchdog count reaches zero, a software watchdog reset is signalled. The enabled software watchdog event then generates an internal hard reset sequence. Bus monitor reset Internal When the MSC7116 bus monitor count reaches zero, a bus monitor hard reset is asserted. The enabled bus monitor event then generates an internal hard reset sequence. JTAG EXTEST, CLAMP, or HIGHZ command Internal When a Test Access Port (TAP) executes an EXTEST, CLAMP, or HIGHZ command, the TAP logic asserts an internal reset signal that generates an internal soft reset sequence. Table 15 summarizes the reset actions that occur as a result of the different reset sources. Table 15. Reset Actions for Each Reset Source Power-On Reset (PORESET) Hard Reset (HRESET) Soft Reset (SRESET) External only External or Internal (Software Watchdog or Bus Monitor) JTAG Command: EXTEST, CLAMP, or HIGHZ Configuration pins sampled (refer to Section 2.5.3.1 for details). Yes No No PLL and clock synthesis states Reset Yes No No HRESET Driven Yes Yes No Software watchdog and bus time-out monitor registers Yes Yes Yes Clock synthesis modules (STOPCTRL, HLTREQ, and HLTACK) reset Yes Yes Yes Extended core reset Yes Yes Yes Peripheral modules reset Yes Yes Yes Reset Action/Reset Source 2.5.3.1 Power-On Reset (PORESET) Pin Asserting PORESET initiates the power-on reset flow. PORESET must be asserted externally for at least 16 CLKIN cycles after external power to the MSC7116 reaches at least 2/3 VDD. MSC7116 Data Sheet, Rev. 13 24 Freescale Semiconductor Electrical Characteristics 2.5.3.2 Reset Configuration The MSC7116 has two mechanisms for writing the reset configuration: * * From a host through the host interface (HDI16) From memory through the I2C interface Five signal levels (see Chapter 1 for signal description details) are sampled on PORESET deassertion to define the boot and operating conditions: * * * * BM[0-1] SWTE H8BIT HDSP 2.5.3.3 Reset Timing Tables Table 16 and Figure 4 describe the reset timing for a reset configuration write. Table 16. Timing for a Reset Configuration Write No. Characteristics Expression Unit 1 Required external PORESET duration minimum 16/FCLKIN clocks 2 Delay from PORESET deassertion to HRESET deassertion 521/FCLKIN clocks Note: Timings are not tested, but are guaranteed by design. 1 PORESET Input Configuration Pins are sampled PORESET Internal HRESET Output(I/O) 2 Figure 4. Timing Diagram for a Reset Configuration Write MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 25 Electrical Characteristics 2.5.4 DDR DRAM Controller Timing This section provides the AC electrical characteristics for the DDR DRAM interface. 2.5.4.1 DDR DRAM Input AC Timing Specifications Table 17 provides the input AC timing specifications for the DDR DRAM interface. Table 17. DDR DRAM Input AC Timing No. Parameter Symbol Min Max Unit -- AC input low voltage VIL -- VREF - 0.31 V -- AC input high voltage VIH VREF + 0.31 VDDM + 0.3 V 201 Maximum Dn input setup skew relative to DQSn input -- -- 900 ps 202 Maximum Dn input hold skew relative to DQSn input -- -- 900 ps Notes: 1. 2. 3. Maximum possible skew between a data strobe (DQSn) and any corresponding bit of data (D[8n + {0...7}] if 0 n 7). See Table 18 for tCK value. Dn should be driven at the same time as DQSn. This is necessary because the DQSn centering on the DQn data tenure is done internally. DQSn 202 202 D0 Dn D1 201 Note: DQS centering is done internally. 201 Figure 5. DDR DRAM Input Timing Diagram 2.5.4.2 DDR DRAM Output AC Timing Specifications Table 18 and Table 19 list the output AC timing specifications and measurement conditions for the DDR DRAM interface. Table 18. DDR DRAM Output AC Timing No. 200 Parameter Symbol CK cycle time, (CK/CK crossing)1 * 100 MHz (DDR200) * 150 MHz (DDR300) Min Max Unit 10 6.67 -- -- ns ns tCK 204 An/RAS/CAS/WE/CKE output setup with respect to CK tDDKHAS 0.5 x tCK - 1000 -- ps 205 An/RAS/CAS/WE/CKE output hold with respect to CK tDDKHAX 0.5 x tCK - 1000 -- ps 206 CSn output setup with respect to CK tDDKHCS 0.5 x tCK - 1000 -- ps 207 CSn output hold with respect to CK tDDKHCX 0.5 x tCK - 1000 -- ps 208 CK to DQSn2 tDDKHMH -600 600 ps MSC7116 Data Sheet, Rev. 13 26 Freescale Semiconductor Electrical Characteristics Table 18. DDR DRAM Output AC Timing (continued) No. Parameter Symbol Min Max Unit 209 Dn/DQMn output setup with respect to DQSn3 tDDKHDS, tDDKLDS 0.25 x tCK - 750 -- ps 210 Dn/DQMn output hold with respect to DQSn3 tDDKHDX, tDDKLDX 0.25 x tCK - 750 -- ps 211 DQSn preamble start4 tDDKHMP -0.25 x tCK -- ps 212 DQSn epilogue end5 tDDKHME -600 600 ps Notes: 1. 2. 3. 4. 5. All CK/CK referenced measurements are made from the crossing of the two signals 0.1 V. tDDKHMH can be modified through the TCFG2[WRDD] DQSS override bits. The DRAM requires that the first write data strobe arrives 75-125% of a DRAM cycle after the write command is issued. Any skew between DQSn and CK must be considered when trying to achieve this 75%-125% goal. The TCFG2[WRDD] bits can be used to shift DQSn by 1/4 DRAM cycle increments. The skew in this case refers to an internal skew existing at the signal connections. By default, the CK/CK crossing occurs in the middle of the control signal (An/RAS/CAS/WE/CKE) tenure. Setting TCFG2[ACSM] bit shifts the control signal assertion 1/2 DRAM cycle earlier than the default timing. This means that the signal is asserted no earlier than 600 ps before the CK/CK crossing and no later than 600 ps after the crossing time; the device uses 1200 ps of the skew budget (the interval from -600 to +600 ps). Timing is verified by referencing the falling edge of CK. See Chapter 10 of the MSC711x Reference Manual for details. Determined by maximum possible skew between a data strobe (DQS) and any corresponding bit of data. The data strobe should be centered inside of the data eye. Please note that this spec is in reference to the DQSn first rising edge. It could also be referenced from CK(r), but due to programmable delay of the write strobes (TCFG2[WRDD]), there pre-amble may be extended for a full DRAM cycle. For this reason, we reference from DQSn. All outputs are referenced to the rising edge of CK. Note that this is essentially the CK/DQSn skew in spec 208. In addition there is no real "maximum" time for the epilogue end. JEDEC does not require this is as a device limitation, but simply for the chip to guarantee fast enough write-to-read turn-around times. This is already guaranteed by the memory controller operation. Figure 6 shows the DDR DRAM output timing diagram. CK CK 200 204 An RAS CAS WE CKE DQMn 206 205 207 Write A0 NOOP 211 208 DQSn 212 209 209 Dn D0 D1 210 210 Figure 6. DDR DRAM Output Timing Diagram MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 27 Electrical Characteristics Figure 7 provides the AC test load for the DDR DRAM bus. Z0 = 50 Output VOUT RL = 50 Figure 7. DDR DRAM AC Test Load Table 19. DDR DRAM Measurement Conditions Symbol VTH1 VOUT 2 Notes: 1. 2. 2.5.5 DDR DRAM Unit VREF 0.31 V V 0.5 x VDDM V Data input threshold measurement point. Data output measurement point. TDM Timing Table 20. TDM Timing No. Characteristic Expression Min Max Units TC 20.0 -- ns TDMxRCK/TDMxTCK High Pulse Width 0.4 x TC 8.0 -- ns 302 TDMxRCK/TDMxTCK Low Pulse Width 0.4 x TC 8.0 -- ns 303 TDM all input Setup time 3.0 -- ns 300 TDMxRCK/TDMxTCK 301 304 TDMxRD Hold time 3.5 -- ns 305 TDMxTFS/TDMxRFS input Hold time 2.0 -- ns 306 TDMxTCK High to TDMxTD output active 4.0 -- ns 307 TDMxTCK High to TDMxTD output valid -- 14.0 ns 308 TDMxTD hold time 2.0 -- ns 309 TDMxTCK High to TDMxTD output high impedance -- 10.0 ns 310 TDMxTFS/TDMxRFS output valid -- 13.5 ns 311 TDMxTFS/TDMxRFS output hold time 2.5 -- ns Notes: 1. 2. Output values are based on 30 pF capacitive load. Inputs are referenced to the sampling that the TDM is programmed to use. Outputs are referenced to the programming edge they are programmed to use. Use of the rising edge or falling edge as a reference is programmable. Refer to the MSC711x Reference Manual for details. TDMxTCK and TDMxRCK are shown using the rising edge. 300 302 301 TDMxRCK 303 304 TDMxRD 305 303 TDMxRFS 310 ~ ~ TDMxRFS (output) 311 Figure 8. TDM Receive Signals MSC7116 Data Sheet, Rev. 13 28 Freescale Semiconductor Electrical Characteristics 300 302 301 TDMxTCK 309 306 TDMxTD TDMxRCK 310 TDMxTFS (output) 305 303 ~ ~ ~ ~ 307 308 311 TDMxTFS (input) Figure 9. TDM Transmit Signals 2.5.6 2.5.6.1 Ethernet Timing Receive Signal Timing Table 21. Receive Signal Timing No. Min Max Unit Receive clock period: * MII: RXCLK (max frequency = 25 MHz) * RMII: REFCLK (max frequency = 50 MHz) 40 20 -- -- ns ns 801 Receive clock pulse width high--as a percent of clock period * MII: RXCLK * RMII: REFCLK 35 14 7 65 -- -- % ns ns 802 Receive clock pulse width low--as a percent of clock period: * MII: RXCLK * RMII: REFCLK 35 14 7 65 -- -- % ns ns 800 Characteristics 803 RXDn, RX_DV, CRS_DV, RX_ER to receive clock rising edge setup time 4 -- ns 804 Receive clock rising edge to RXDn, RX_DV, CRS_DV, RX_ER hold time 2 -- ns 800 801 802 Receive clock RXDn RX_DV CRS_DV RX_ER 803 804 Valid Figure 10. Ethernet Receive Signal Timing MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 29 Electrical Characteristics 2.5.6.2 Transmit Signal Timing Table 22. Transmit Signal Timing No. Min Max Unit Transmit clock period: * MII: TXCLK * RMII: REFCLK 40 20 -- -- ns ns 801 Transmit clock pulse width high--as a percent of clock period * MII: RXCLK * RMII: REFCLK 35 14 7 65 -- -- % ns ns 802 Transmit clock pulse width low--as a percent of clock period: * MII: RXCLK * RMII: REFCLK 35 14 7 65 -- -- % ns ns 800 Characteristics 805 Transmit clock to TXDn, TX_EN, TX_ER invalid 4 -- ns 806 Transmit clock to TXDn, TX_EN, TX_ER valid -- 14 ns Min Max Unit 60 30 -- -- ns ns 800 801 Transmit clock 802 806 805 TXDn TX_EN TX_ER Valid Figure 11. Ethernet Receive Signal Timing 2.5.6.3 Asynchronous Input Signal Timing Table 23. Asynchronous Input Signal Timing No. 807 Characteristics * MII: CRS and COL minimum pulse width (1.5 x TXCLK period) * RMII: CRS_DV minimum pulse width (1.5 x REFCLK period) CRS COL CRS_DV 807 Figure 12. Asynchronous Input Signal Timing MSC7116 Data Sheet, Rev. 13 30 Freescale Semiconductor Electrical Characteristics 2.5.6.4 Management Interface Timing Table 24. Ethernet Controller Management Interface Timing No. Characteristics Min Max Unit 808 MDC period 400 -- ns 809 MDC pulse width high 160 -- ns 810 MDC pulse width low 160 -- ns 811 MDS falling edge to MDIO output invalid (minimum propagation delay) 0 -- ns 812 MDS falling edge to MDIO output valid (maximum propagation delay) -- 15 ns 813 MDIO input to MDC rising edge setup time 10 -- ns 814 MDC rising edge to MDIO input hold time 10 -- ns 808 809 810 MDC (output) 811 MDIO (output) 812 813 814 MDIO (input) Figure 13. Serial Management Channel Timing MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 31 Electrical Characteristics 2.5.7 HDI16 Signals Table 25. Host Interface (HDI16) Timing1, 2 No. 40 44a 44b 44c 45 46 47 48 49 50 51 52 53 54 55 56 57 58 61 62 63 64 Notes: Characteristics3 Expression Value Unit Host Interface Clock period TCORE Note 1 ns Read data strobe minimum assertion width4 Note 11 ns 2.0 x TCORE + 9.0 HACK read minimum assertion width 1.5 x TCORE Note 11 ns Read data strobe minimum deassertion width4 HACK read minimum deassertion width 2.5 x TCORE Note 11 ns Read data strobe minimum deassertion width4 after "Last Data Register" reads5,6, or between two consecutive CVR, ICR, or ISR reads7 HACK minimum deassertion width after "Last Data Register" reads5,6 1.5 x TCORE Write data strobe minimum assertion width8 Note 11 ns HACK write minimum assertion width Write data strobe minimum deassertion width8 HACK write minimum deassertion width after ICR, CVR and Data Register writes5 2.5 x TCORE Note 11 ns Host data input minimum setup time before write data strobe deassertion8 Host data input minimum setup time before HACK write deassertion -- 2.5 ns Host data input minimum hold time after write data strobe deassertion8 Host data input minimum hold time after HACK write deassertion -- 2.5 ns Read data strobe minimum assertion to output data active from high impedance4 HACK read minimum assertion to output data active from high impedance -- 1.0 ns Read data strobe maximum assertion to output data valid4 HACK read maximum assertion to output data valid (2.0 x TCORE) + 8.0 Note 11 ns Read data strobe maximum deassertion to output data high impedance4 HACK read maximum deassertion to output data high impedance -- 9.0 ns Output data minimum hold time after read data strobe deassertion4 -- 1.0 ns Output data minimum hold time after HACK read deassertion HCS[1-2] minimum assertion to read data strobe assertion4 -- 0.5 ns HCS[1-2] minimum assertion to write data strobe assertion8 -- 0.0 ns HCS[1-2] maximum assertion to output data valid (2.0 x TCORE) + 6.0 Note 11 ns -- 0.5 ns HCS[1-2] minimum hold time after data strobe deassertion9 HA[0-2], HRW minimum setup time before data strobe assertion9 -- 5.0 ns HA[0-2], HRW minimum hold time after data strobe deassertion9 -- 5.0 ns Maximum delay from read data strobe deassertion to host request (3.0 x TCORE) + 6.0 Note 11 ns deassertion for "Last Data Register" read4, 5, 10 Maximum delay from write data strobe deassertion to host request deassertion for "Last Data Register" write5,8,10 (3.0 x TCORE) + 6.0 Note 11 ns Minimum delay from DMA HACK (OAD=0) or Read/Write data strobe(OAD=1) deassertion to HREQ assertion. (2.0 x TCORE) + 1.0 Note 11 ns Maximum delay from DMA HACK (OAD=0) or Read/Write data strobe(OAD=1) assertion to HREQ deassertion (5.0 x TCORE) + 6.0 Note 11 ns 1. TCORE = core clock period. At 300 MHz, TCORE = 3.333 ns. 2. In the timing diagrams below, the controls pins are drawn as active low. The pin polarity is programmable. 3. VDD = 3.3 V 0.15 V; TJ = -40C to +105 C, CL = 30 pF for maximum delay timings and CL = 0 pF for minimum delay timings. 4. The read data strobe is HRD/HRD in the dual data strobe mode and HDS/HDS in the single data strobe mode. 5. For 64-bit transfers, the "last data register" is the register at address 0x7, which is the last location to be read or written in data transfers. This is RX0/TX0 in the little endian mode (HBE = 0), or RX3/TX3 in the big endian mode (HBE = 1). 6. This timing is applicable only if a read from the "last data register" is followed by a read from the RX[0-3] registers without first polling RXDF or HREQ bits, or waiting for the assertion of the HREQ/HREQ signal. 7. This timing is applicable only if two consecutive reads from one of these registers are executed. 8. The write data strobe is HWR in the dual data strobe mode and HDS in the single data strobe mode. 9. The data strobe is host read (HRD/HRD) or host write (HWR/HWR) in the dual data strobe mode and host data strobe (HDS/HDS) in the single data strobe mode. 10. The host request is HREQ/HREQ in the single host request mode and HRRQ/HRRQ and HTRQ/HTRQ in the double host request mode. HRRQ/HRRQ is deasserted only when HOTX fifo is empty, HTRQ/HTRQ is deasserted only if HORX fifo is full 11. Compute the value using the expression. 12. The read and write data strobe minimum deassertion width for non-"last data register" accesses in single and dual data strobe modes is based on timings 57 and 58. MSC7116 Data Sheet, Rev. 13 32 Freescale Semiconductor Figure 14 and Figure 15 show HDI16 read signal timing. Figure 16 and Figure 17 show HDI16 write signal timing. HA[0-2] 57 58 56 53 HCS[1-2] 57 58 HRW 44a HDS 44b 51 55 44c 50 52 49 HD[0-15] 61 HREQ (single host request) HRRQ (double host request) Figure 14. Read Timing Diagram, Single Data Strobe HA[0-2] 57 58 56 53 HCS[1-2] 44a HRD 44b 51 55 44a 50 52 49 HD[0-15] 61 HREQ (single host request) HRRQ (double host request) Figure 15. Read Timing Diagram, Double Data Strobe MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 33 HA[0-2] 57 58 56 54 HCS[1-2] 57 58 HRW 45 HDS 46 47 48 HD[0-15] 62 HREQ (single host request) HTRQ (double host request) Figure 16. Write Timing Diagram, Single Data Strobe HA[0-2] 57 58 56 54 HCS[1-2] 45 HWR 46 48 47 HD[0-15] 62 HREQ (single host request) HTRQ (double host request) Figure 17. Write Timing Diagram, Double Data Strobe MSC7116 Data Sheet, Rev. 13 34 Freescale Semiconductor HREQ (Output) 63 64 44a 44b RX[0-3] HACK Read 51 50 49 52 Data Valid HD[0-15] (Output) Figure 18. Host DMA Read Timing Diagram, HPCR[OAD] = 0 HREQ (Output) 63 64 46 45 HACK TX[0-3] Write 47 48 HD[0-15] (Input) Data Valid Figure 19. Host DMA Write Timing Diagram, HPCR[OAD] = 0 MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 35 2.5.8 I2C Timing Table 26. I2C Timing Fast No. Characteristic Unit Min Max 0 400 kHz 450 SCL clock frequency 451 Hold time START condition (SCL clock period/2) - 0.3 -- s 452 SCL low period (SCL clock period/2) - 0.3 -- s 453 SCL high period (SCL clock period/2) - 0.1 -- s 454 Repeated START set-up time (not shown in figure) 2 x 1/FBCK -- s 455 Data hold time 0 -- s 456 Data set-up time 250 -- ns 457 SDA and SCL rise time -- 700 ns 458 SDA and SCL fall time -- 300 ns 459 Set-up time for STOP (SCL clock period/2) - 0.7 -- s 460 Bus free time between STOP and START (SCL clock period/2) - 0.3 -- s Note: SDA set-up time is referenced to the rising edge of SCL. SDA hold time is referenced to the falling edge of SCL. Load capacitance on SDA and SCL is 400 pF. 453 458 Start Condition 1 SCL 2 3 457 4 452 451 SDA 5 6 7 8 Stop Condition Start Condition 9 A C K Data Byte 457 458 459 460 Start Condition SCL SDA Data Byte Figure 20. I2C Timing Diagram MSC7116 Data Sheet, Rev. 13 36 Freescale Semiconductor 2.5.9 UART Timing Table 27. UART Timing No. Characteristics Expression Min Max Unit MHz -- Internal bus clock (APBCLK) FCORE/2 -- 133 -- Internal bus clock period (1/APBCLK) TAPBCLK 7.52 -- ns 16 x TAPBCLK 120.3 -- ns 400 URXD and UTXD inputs high/low duration 401 URXD and UTXD inputs rise/fall time -- 5 ns 402 UTXD output rise/fall time -- 5 ns 401 401 UTXD, URXD inputs 400 400 Figure 21. UART Input Timing 402 402 UTXD Output Figure 22. UART Output Timing 2.5.10 EE Timing Table 28. EE0 Timing Number Notes: Characteristics 65 EE0 input to the core 66 EE0 output from the core 1. 2. 3. Type Min Asynchronous 4 core clock periods Synchronous to core clock 1 core clock period The core clock is the SC1400 core clock. The ratio between the core clock and CLKOUT is configured during power-on-reset. Configure the direction of the EE pin in the EE_CTRL register (see the SC140/SC1400 Core Reference Manual for details. Refer to Table 1-11 on page 1-16 for details on EE pin functionality. Figure 24 shows the signal behavior of the EE pin. 65 EE0 In 66 EE0 Out Figure 23. EE Pin Timing MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 37 2.5.11 Event Timing Table 29. EVNT Signal Timing Number Characteristics 67 EVNT as input 68 EVNT as output Notes: 1. 2. 3. Type Min Asynchronous 1.5 x APBCLK periods Synchronous to core clock 1 APBCLK period Refer to Table 27 for a definition of the APBCLK period. Direction of the EVNT signal is configured through the GPIO and Event port registers. Refer to the signal chapter in the MSC711x Reference Manual for details on EVNT pin functionality. Figure 24 shows the signal behavior of the EVNT pins. 67 EVNT in 68 EVNT out Figure 24. EVNT Pin Timing 2.5.12 GPIO Timing Table 30. GPIO Signal Timing1,2,3 Number Notes: Type Min 601 GPI4.5 Asynchronous 1.5 x APBCLK periods 602 GPO5 Synchronous to core clock 1 APBCLK period 603 Port A edge-sensitive interrupt Asynchronous 1.5 x APBCLK periods 604 Port A level-sensitive interrupt Asynchronous 3 x APBCLK periods6 1. 2. 3. 4. 5. 6. Characteristics Refer to Table 27 for a definition of the APBCLK period. Direction of the GPIO signal is configured through the GPIO port registers. Refer to Section 1.5 for details on GPIO pin functionality. GPI data is synchronized to the APBCLK internally and the minimum listed is the capability of the hardware to capture data into a register when the GPADR is read. The specification is not tested due to the asynchronous nature of the input and dependence on the state of the DSP core. It is guaranteed by design. The output signals cannot toggle faster than 75 MHz. Level-sensitive interrupts should be held low until the system determines (via the service routine) that the interrupt is acknowledged. Figure 25 shows the signal behavior of the GPI/GPO pins. 601 GPI 602 GPO Figure 25. GPI/GPO Pin Timing MSC7116 Data Sheet, Rev. 13 38 Freescale Semiconductor 2.5.13 JTAG Signals Table 31. JTAG Timing All frequencies No. Characteristics Unit Min Max 700 TCK frequency of operation (1/(TC x 3) Note: TC = 1/CLOCK which is the period of the core clock. The TCK frequency must less than 1/3 of the core frequency with an absolute maximum limit of 40 MHz. 0.0 40.0 MHz 701 TCK cycle time 25.0 -- ns 702 TCK clock pulse width measured at VM = 1.6 V 11.0 -- ns 703 TCK rise and fall times 0.0 3.0 ns 704 Boundary scan input data set-up time 5.0 -- ns 705 Boundary scan input data hold time 14.0 -- ns 706 TCK low to output data valid 0.0 20.0 ns 707 TCK low to output high impedance 0.0 20.0 ns 708 TMS, TDI data set-up time 5.0 -- ns 709 TMS, TDI data hold time 14.0 -- ns 710 TCK low to TDO data valid 0.0 24.0 ns 711 TCK low to TDO high impedance 0.0 10.0 ns 712 TRST assert time 100.0 -- ns Note: All timings apply to OCE module data transfers as the OCE module uses the JTAG port as an interface. 701 702 TCK (Input) VIH VM VM VIL 703 703 Figure 26. Test Clock Input Timing Diagram MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 39 VIH TCK (Input) VIL 704 Data Inputs 705 Input Data Valid 706 Data Outputs Output Data Valid 707 Data Outputs Figure 27. Boundary Scan (JTAG) Timing Diagram TCK (Input) VIH VIL 708 TDI TMS (Input) 709 Input Data Valid 710 TDO (Output) Output Data Valid 711 TDO (Output) Figure 28. Test Access Port Timing Diagram TRST (Input) 712 Figure 29. TRST Timing Diagram MSC7116 Data Sheet, Rev. 13 40 Freescale Semiconductor Hardware Design Considerations 3 Hardware Design Considerations This section described various areas to consider when incorporating the MSC7116 device into a system design. 3.1 Thermal Design Considerations An estimation of the chip-junction temperature, TJ, in C can be obtained from the following: TJ = TA + (RJA x PD) Eqn. 1 where TA = ambient temperature near the package (C) RJA = junction-to-ambient thermal resistance (C/W) PD = PINT + PI/O = power dissipation in the package (W) PINT = IDD x VDD = internal power dissipation (W) PI/O = power dissipated from device on output pins (W) The power dissipation values for the MSC7116 are listed in Table 4. The ambient temperature for the device is the air temperature in the immediate vicinity that would cool the device. The junction-to-ambient thermal resistances are JEDEC standard values that provide a quick and easy estimation of thermal performance. There are two values in common usage: the value determined on a single layer board and the value obtained on a board with two planes. The value that more closely approximates a specific application depends on the power dissipated by other components on the printed circuit board (PCB). The value obtained using a single layer board is appropriate for tightly packed PCB configurations. The value obtained using a board with internal planes is more appropriate for boards with low power dissipation (less than 0.02 W/cm2 with natural convection) and well separated components. Based on an estimation of junction temperature using this technique, determine whether a more detailed thermal analysis is required. Standard thermal management techniques can be used to maintain the device thermal junction temperature below its maximum. If TJ appears to be too high, either lower the ambient temperature or the power dissipation of the chip. You can verify the junction temperature by measuring the case temperature using a small diameter thermocouple (40 gauge is recommended) or an infrared temperature sensor on a spot on the device case. Use the following equation to determine TJ: TJ = TT + (JT x PD) Eqn. 2 where TT = thermocouple (or infrared) temperature on top of the package (C) JT = thermal characterization parameter (C/W) PD = power dissipation in the package (W) MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 41 Hardware Design Considerations 3.2 Power Supply Design Considerations This section outlines the MSC7116 power considerations: power supply, power sequencing, power planes, decoupling, power supply filtering, and power consumption. It also presents a recommended power supply design and options for low-power consumption. For information on AC/DC electrical specifications and thermal characteristics, refer to Section 2. 3.2.1 Power Supply The MSC7116 requires four input voltages, as shown in Table 32. Table 32. MSC7116 Voltages Voltage Symbol Value Core VDDC 1.2 V Memory VDDM 2.5 V Reference VREF 1.25 V I/O VDDIO 3.3 V You should supply the MSC7116 core voltage via a variable switching supply or regulator to allow for compatibility with possible core voltage changes on future silicon revisions. The core voltage is supplied with 1.2 V (+5% and -10%) across VDDC and GND and the I/O section is supplied with 3.3 V ( 10%) across VDDIO and GND. The memory and reference voltages supply the DDR memory controller block. The memory voltage is supplied with 2.5 V across VDDM and GND. The reference voltage is supplied across VREF and GND and must be between 0.49 x VDDM and 0.51 x VDDM. Refer to the JEDEC standard JESD8 (Stub Series Terminated Logic for 2.5 Volts (STTL_2)) for memory voltage supply requirements. 3.2.2 Power Sequencing One consequence of multiple power supplies is that the voltage rails ramp up at different rates when power is initially applied. The rates depend on the power supply, the type of load on each power supply, and the way different voltages are derived. It is extremely important to observe the power up and power down sequences at the board level to avoid latch-up, forward biasing of ESD devices, and excessive currents, which all lead to severe device damage. Note: There are five possible power-up/power-down sequence cases. The first four cases listed in the following sections are recommended for new designs. The fifth case is not recommended for new designs and must be carefully evaluated for current spike risks based on actual information for the specific application. MSC7116 Data Sheet, Rev. 13 42 Freescale Semiconductor Hardware Design Considerations 3.2.2.1 Case 1 The power-up sequence is as follows: 1. 2. 3. 4. Turn on the VDDIO (3.3 V) supply first. Turn on the VDDC (1.2 V) supply second. Turn on the VDDM (2.5 V) supply third. Turn on the VREF (1.25 V) supply fourth (last). The power-down sequence is as follows: 1. 2. 3. 4. Turn off the VREF (1.25 V) supply first. Turn off the VDDM (2.5 V) supply second. Turn off the VDDC (1.2 V) supply third. Turn of the VDDIO (3.3 V) supply fourth (last). Use the following guidelines: * * * Make sure that the time interval between the ramp-down of VDDIO and VDDC is less than 10 ms. Make sure that the time interval between the ramp-up or ramp-down for VDDC and VDDM is less than 10 ms for power-up and power-down. Refer to Figure 30 for relative timing for power sequencing case 1. Ramp-down Ramp-up VDDIO = 3.3 V Voltage VDDM = 2.5 V VREF = 1.25 V VDDC = 1.2 V <10 ms <10 ms <10 ms <10 ms Time Figure 30. Voltage Sequencing Case 1 MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 43 Hardware Design Considerations 3.2.2.2 Case 2 The power-up sequence is as follows: 1. 2. 3. Note: Turn on the VDDIO (3.3 V) supply first. Turn on the VDDC (1.2 V) and VDDM (2.5 V) supplies simultaneously (second). Turn on the VREF (1.25 V) supply last (third). Make sure that the time interval between the ramp-up of VDDIO and VDDC/VDDM is less than 10 ms. The power-down sequence is as follows: 1. 2. 3. 4. Turn off the VREF (1.25 V) supply first. Turn off the VDDM (2.5 V) supply second. Turn off the VDDC (1.2 V) supply third. Turn of the VDDIO (3.3 V) supply fourth (last). Use the following guidelines: * * * Make sure that the time interval between the ramp-down for VDDIO and VDDC is less than 10 ms. Make sure that the time interval between the ramp-up or ramp-down for VDDC and VDDM is less than 10 ms for power-up and power-down. Refer to Figure 31 for relative timing for Case 2. Ramp-down Ramp-up VDDIO = 3.3 V Voltage VDDM = 2.5 V VREF = 1.25 V VDDC = 1.2 V <10 ms <10 ms <10 ms Time Figure 31. Voltage Sequencing Case 2 MSC7116 Data Sheet, Rev. 13 44 Freescale Semiconductor Hardware Design Considerations 3.2.2.3 Case 3 The power-up sequence is as follows: 1. 2. 3. Note: Turn on the VDDIO (3.3 V) supply first. Turn on the VDDC (1.2 V) supply second. Turn on the VDDM (2.5 V) and VREF (1.25 V) supplies simultaneously (third). Make sure that the time interval between the ramp-up of VDDIO and VDDC is less than 10 ms. The power-down sequence is as follows: 1. 2. 3. Turn off the VDDM (2.5 V) and VREF (1.25 V) supplies simultaneously (first). Turn off the VDDC (1.2 V) supply second. Turn of the VDDIO (3.3 V) supply third (last). Use the following guidelines: * * * Make sure that the time interval between the ramp-down for VDDIO and VDDC is less than 10 ms. Make sure that the time interval between the ramp-up or ramp-down time for VDDC and VDDM is less than 10 ms for power-up and power-down. Refer to Figure 32 for relative timing for Case 3. Ramp-down Ramp-up VDDIO = 3.3 V Voltage VDDM = 2.5 V VREF = 1.25 V VDDC = 1.2 V <10 ms <10 ms <10 ms <10 ms Time Figure 32. Voltage Sequencing Case 3 MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 45 Hardware Design Considerations 3.2.2.4 Case 4 The power-up sequence is as follows: 1. 2. Note: Turn on the VDDIO (3.3 V) supply first. Turn on the VDDC (1.2 V), VDDM (2.5 V), and VREF (1.25 V) supplies simultaneously (second). Make sure that the time interval between the ramp-up of VDDIO and VDDC is less than 10 ms. The power-down sequence is as follows: 1. 2. Turn off the VDDC (1.2 V), VREF (1.25 V), and VDDM (2.5 V) supplies simultaneously (first). Turn of the VDDIO (3.3 V) supply last. Use the following guidelines: * * Make sure that the time interval between the ramp-up or ramp-down time for VDDC and VDDM is less than 10 ms for power-up and power-down. Refer to Figure 33 for relative timing for Case 4. Ramp-down Ramp-up VDDIO = 3.3 V Voltage VDDM = 2.5 V VREF = 1.25 V VDDC = 1.2 V <10 ms <10 ms Time Figure 33. Voltage Sequencing Case 4 MSC7116 Data Sheet, Rev. 13 46 Freescale Semiconductor Hardware Design Considerations 3.2.2.5 Case 5 (not recommended for new designs) The power-up sequence is as follows: 1. 2. 3. 4. Note: Turn on the VDDIO (3.3 V) supply first. Turn on the VDDM (2.5 V) supply second. Turn on the VDDC (1.2 V) supply third. Turn on the VREF (1.25 V) supply fourth (last). Make sure that the time interval between the ramp-up of VDDIO and VDDM is less than 10 ms. The power-down sequence is as follows: 1. 2. 3. 4. Turn off the VREF (1.25 V) supply first. Turn off the VDDC (1.2 V) supply second. Turn off the VDDM (2.5 V) supply third. Turn of the VDDIO (3.3 V) supply fourth (last). Use the following guidelines: * * * Make sure that the time interval between the ramp-down of VDDIO and VDDM is less than 10 ms. Make sure that the time interval between the ramp-up or ramp-down for VDDC and VDDM is less than 2 ms for power-up and power-down. Refer to Figure 34 for relative timing for power sequencing case 5. Ramp-down Ramp-up VDDIO = 3.3 V Voltage VDDM = 2.5 V VREF = 1.25 V VDDC = 1.2 V <2 ms <2 ms <10 ms <10 ms Time Figure 34. Voltage Sequencing Case 5 Note: Cases 1, 2, 3, and 4 are recommended for system design. Designs that use Case 5 may have large current spikes on the VDDM supply at startup and is not recommended for most designs. If a design uses case 5, it must accommodate the potential current spikes. Verify risks related to current spikes using actual information for the specific application. MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 47 Hardware Design Considerations 3.2.3 Power Planes Each power supply pin (VDDC, VDDM, and VDDIO) should have a low-impedance path to the board power supply. Each GND pin should be provided with a low-impedance path to ground. The power supply pins drive distinct groups of logic on the device. The MSC7116 VDDC power supply pins should be bypassed to ground using decoupling capacitors. The capacitor leads and associated printed circuit traces connecting to device power pins and GND should be kept to less than half an inch per capacitor lead. A minimum four-layer board that employs two inner layers as power and GND planes is recommended. See Section 3.5 for DDR Controller power guidelines. 3.2.4 Decoupling Both the I/O voltage and core voltage should be decoupled for switching noise. For I/O decoupling, use standard capacitor values of 0.01 F for every two to three voltage pins. For core voltage decoupling, use two levels of decoupling. The first level should consist of a 0.01 F high frequency capacitor with low effective series resistance (ESR) and effective series inductance (ESL) for every two to three voltage pins. The second decoupling level should consist of two bulk/tantalum decoupling capacitors, one 10 F and one 47 F, (with low ESR and ESL) mounted as closely as possible to the MSC7116 voltage pins. Additionally, the maximum drop between the power supply and the DSP device should be 15 mV at 1 A. 3.2.5 PLL Power Supply Filtering The MSC7116 VDDPLL power signal provides power to the clock generation PLL. To ensure stability of the internal clock, the power supplied to this pin should be filtered with capacitors that have low and high frequency filtering characteristics. VDDPLL can be connected to VDDC through a 2 resistor. VSSPLL can be tied directly to the GND plane. A circuit similar to the one shown in Figure 35 is recommended. The PLL loop filter should be placed as closely as possible to the VDDPLL pin (which are located on the outside edge of the silicon package) to minimize noise coupled from nearby circuits.The 0.01 F capacitor should be closest to VDDPLL, followed by the 0.1 F capacitor, the 10 F capacitor, and finally the 2- resistor to VDDC. These traces should be kept short. 2 VDDC VDDPLL 10 F 0.1 F 0.01 F Figure 35. PLL Power Supply Filter Circuits 3.2.6 Power Consumption You can reduce power consumption in your design by controlling the power consumption of the following regions of the device: * * * * Extended core. Use the SC1400 Stop and Wait modes by issuing a stop or wait instruction. Clock synthesis module. Disable the PLL, timer, watchdog, or DDR clocks or disable the CLKO pin. AHB subsystem. Freeze or shut down the AHB subsystem using the GPSCTL[XBR_HRQ] bit. Peripheral subsystem. Halt the individual on-device peripherals such as the DDR memory controller, Ethernet MAC, HDI16, TDM, UART, I2C, and timer modules. For details, see the "Clocks and Power Management" chapter of the MSC711x Reference Manual. MSC7116 Data Sheet, Rev. 13 48 Freescale Semiconductor Hardware Design Considerations 3.2.7 Power Supply Design One of the most common ways to derive power is to use either a simple fixed or adjustable linear regulator. For the system I/O voltage supply, a simple fixed 3.3 V supply can be used. However, a separate adjustable linear regulator supply for the core voltage VDDC should be implemented. For the memory power supply, regulators are available that take care of all DDR power requirements. Table 33. Recommended Power Supply Ratings Supply Symbol Nominal Voltage Current Rating Core VDDC 1.2 V 1.5 A per device Memory VDDM 2.5 V 0.5 A per device Reference VREF 1.25 V 10 A per device I/O VDDIO 3.3 V 1.0 A per device 3.3 Estimated Power Usage Calculations The following equations permit estimated power usage to be calculated for individual design conditions. Overall power is derived by totaling the power used by each of the major subsystems: PTOTAL = PCORE + PPERIPHERALS + PDDRIO + PIO + PLEAKAGE Eqn. 3 This equation combines dynamic and static power. Dynamic power is determined using the generic equation: C x V2 x F x 10-3 mW Eqn. 4 where, C = load capacitance in pF V = peak-to-peak voltage swing in V F = frequency in MHz 3.3.1 Core Power Estimation of core power is straightforward. It uses the generic dynamic power equation and assumes that the core load capacitance is 750 pF, core voltage swing is 1.2 V, and the core frequency is 266 MHz. This yields: PCORE = 750 pF x (1.2 V)2 x 266 MHz x 10-3 = 287 mW Eqn. 5 This equation allows for adjustments to voltage and frequency if necessary. MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 49 Hardware Design Considerations 3.3.2 Peripheral Power Peripherals include the DDR memory controller, Ethernet controller, DMA controller, HDI16, TDM, UART, timers, GPIOs, and the I2C module. Basic power consumption by each module is assumed to be the same and is computed by using the following equation which assumes an effective load of 20 pF, core voltage swing of 1.2 V, and a switching frequency of 133 MHz. This yields: PPERIPHERAL = 20 pF x (1.2 V)2 x 133 MHz x 10-3 = 3.83 mW per peripheral Eqn. 6 Multiply this value by the number of peripherals used in the application to compute the total peripheral power consumption. 3.3.3 External Memory Power Estimation of power consumption by the DDR memory system is complex. It varies based on overall system signal line usage, termination and load levels, and switching rates. Because the DDR memory includes terminations external to the MSC7116 device, the 2.5 V power source provides the power for the termination, which is a static value of 16 mA per signal driven high. The dynamic power is computed, however, using a differential voltage swing of 0.200 V, yielding a peak-to-peak swing of 0.4 V. The equations for computing the DDR power are: PDDRIO = PSTATIC + PDYNAMIC Eqn. 7 PSTATIC = (unused pins x % driven high) x 16 mA x 2.5 V Eqn. 8 PDYNAMIC = (pin activity value) x 20 pF x (0.4 V)2 x 266 MHz x 10-3 mW Eqn. 9 pin activity value = (active data lines x % activity x % data switching) + (active address lines x % activity) Eqn. 10 As an example, assume the following: unused pins = 16 (DDR uses 16-pin mode) % driven high = 50% active data lines = 16 % activity = 60% % data switching = 50% active address lines = 3 In this example, the DDR memory power consumption is: PDDRIO = ((16 x 0.5) x 16 x 2.5) + (((16 x 0.6 x 0.5) + (3 x 0.6)) x 20 x (0.4)2 x 266 x 10-3) = 326.3 mW 3.3.4 Eqn. 11 External I/O Power The estimation of the I/O power is similar to the computation of the peripheral power estimates. The power consumption per signal line is computed assuming a maximum load of 20 pF, a voltage swing of 3.3 V, and a switching frequency of 33 MHz, which yields: PIO = 20 pF x (3.3 V)2 x 33 MHz x 10-3 = 7.19 mW per I/O line Eqn. 12 Multiply this number by the number of I/O signal lines used in the application design to compute the total I/O power. Note: 3.3.5 The signal loading depends on the board routing. For systems using a single DDR device, the load could be as low as 7 pF. Leakage Power The leakage power is for all power supplies combined at a specific temperature. The value is temperature dependent. The observed leakage value at room temperature is 64 mW. MSC7116 Data Sheet, Rev. 13 50 Freescale Semiconductor Hardware Design Considerations 3.3.6 Example Total Power Consumption Using the examples in this section and assuming four peripherals and 10 I/O lines active, a total power consumption value is estimated as the following: PTOTAL = 287 + (4 x 3.83) + 326.3 + (10 x 7.19) + 64 = 764.52 mW 3.4 Eqn. 13 Reset and Boot This section describes the recommendations for configuring the MSC7116 at reset and boot. 3.4.1 Reset Circuit HRESET is a bidirectional signal and, if driven as an input, should be driven with an open collector or open-drain device. For an open-drain output such as HRESET, take care when driving many buffers that implement input bus-hold circuitry. The bus-hold currents can cause enough voltage drop across the pull-up resistor to change the logic level to low. Either a smaller value of pull-up or less current loading from the bus-hold drivers overcomes this issue. To avoid exceeding the MSC7116 output current, the pull-up value should not be too small (a 1 K pull-up resistor is used in the MSC711xADS reference design). 3.4.2 Reset Configuration Pins Table 34 shows the MSC7116 reset configuration signals. These signals are sampled at the deassertion (rising edge) of PORESET. For details, refer to the Reset chapter of the MSC711x Reference Manual. Table 34. Reset Configuration Signals Signal BM[3-0] SWTE Description Settings Determines boot mode. See Table 35 for details. Determines watchdog functionality. 0 HDSP Configures HDI16 strobe polarity. H8BIT Configures HDI16 operation mode. Watchdog timer disabled. 1 Watchdog timer enabled. 0 Host Data strobes active low. 1 Host Data strobes active high. 0 HDI16 port configured for 16-bit operation. 1 HDI16 port configured for 8-bit operation. MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 51 Hardware Design Considerations Table 35. Boot Mode Source Selection Boot Port BM[3-0] Input Clock Frequency Clock Divide PLL CKSEL RNG Bit Core Clock Frequency Comments HDI Boot Modes 0000 HDI16 < Fmax N/A N/A 00 0 < Fmax Not clocked by the PLL. Can boot as 8- or 16-bit HDI. 0101 HDI16 22.2-25 MHz 1 12 11 1 266-300 MHz Can boot as 8- or 16-bit HDI. 0010 HDI16 25-33.3 MHz 2 32 01 1 200-266 MHz 0111 HDI16 33-66 MHz 3 12 11 1 132-264 MHz 0100 HDI16 44.3-50 MHz 2 12 11 1 266-300 MHz SPI Boot Modes - Using HA3, HCS2, BM3, BM2 Pins 1000 SPI (SW) < Fmax N/A N/A 00 0 < Fmax 1001 SPI (SW) 15.6-25 MHz 1 17 11 0 133-212.5 MHz 1010 SPI (SW) 33-50 MHz 2 16 11 0 132-200 MHz 1011 SPI (SW) 44.3-75 MHz 3 18 11 0 133-225 MHz The boot program automatically determines whether EEPROM or Flash memory. SPI Boot Modes - Using URXD, UTXD, SCL, SDA Pins < Fmax N/A N/A 00 0 < Fmax I2C < 100 MHz N/A N/A 00 0 < 100 MHz Not clocked by the PLL. I2C is limited to a maximum bit rate of 400 Kbps. With a clock divider of 128, this limits the maximum input clock frequency to 100 MHz. 0011 Reserved -- -- -- -- -- -- -- 0110 Reserved -- -- -- -- -- -- -- 1101 Reserved -- -- -- -- -- -- -- 1110 Reserved -- -- -- -- -- -- -- 1111 Reserved -- -- -- -- -- -- -- 1100 SPI (SW) Boots through different set of pins. I2C Boot Modes 0001 Reserved Notes: 1. 2. 3. 3.4.3 The clock divider determines the value used in the clock module CLKCTRL[PLLDVF] field. The clock multiplier determines the value used in the clock module CLKCTRL[PLLMLTF] field. Fmax is determined by the maximum frequency of the peripheral and of the SC1400 core as specified in the data sheet. Boot After a power-on reset, the PLL is bypassed and the device is directly clocked from the CLKIN pin. Thus, the device operates slowly during the boot process. After the boot program is loaded, it can enable the PLL and start the device operating at a higher speed. The MSC7116 can boot from an external host through the HDI16 or download a user program through the I2C port. The boot operating mode is set by configuring the BM[0-3] signals sampled at the rising edge of PORESET, as shown in Table 35. See the MSC711x Reference Manual for details of boot program operation. 3.4.3.1 HDI16 Boot If the MSC7116 device boots from an external host through the HDI16, the port is configured as follows: * * * * Operate in Non-DMA mode. Operate in polled mode on the device side. Operate in polled mode on the external host side. External host must write four 16-bit values at a time with the first word as the most significant and the fourth word as the least significant. MSC7116 Data Sheet, Rev. 13 52 Freescale Semiconductor Hardware Design Considerations When booting from a power-on reset, the HDI16 is additionally configurable as follows: * * 8- or 16-bit mode as specified by the H8BIT pin. Data strobe as specified by the HDSP and HDDS pins. These pins are sampled only on the deassertion of power-on reset. During a boot from a hard reset, the configuration of these pins is unaffected. Note: When the HDI16 is used for booting or other purposes, bit 0 is the least significant bit and not the most significant bit as for other DSP products. 3.4.3.2 I2C Boot When the MSC7116 device is configured to boot from the I2C port, the boot program configures the GPIO pins for I2C operation. Then the MSC7116 device initiates accesses to the I2C module, downloading data to the MSC7116 device. The I2C interface is configured as follows: * * * * * PLL is disabled and bypassed so that the I2C module is clocked with the IPBus clock. I2C interface operates in master mode and polling is used. EPROM operates in slave mode. Clock divider is set to 128. Address of slave during boot is 0xA0. The IPBus clock is internally divided to generate the bit clock, as follows: * * * * CLKIN must be a maximum of 100 MHz PLL is bypassed. IPBus clock = CLKIN/2 is a maximum of 50 MHz. I2C bit clock must be less than or equal to: -- IPBus clock/I2C clock divider -- 50 MHz (max)/128 -- 390.6 KHz This satisfies the maximum clock rate requirement of 400 kbps for the I2C interface. For details on the boot procedure, see the "Boot Program" chapter of the MSC711x Reference Manual. 3.4.3.3 SPI Boot When the MSC7116 device is configured to boot from the SPI port, the boot program configures the GPIO pins for SPI operation. Then the MSC7116 device initiates accesses to the SPI module, downloading data to the MSC7116 device. When the SPI routines run in the boot ROM, the MSC7116 is always configured as the SPI master. Booting through the SPI is supported for serial EEPROM devices and serial Flash devices. When a READ_ID instruction is issued to the serial memory device and the device returns a value of 0x00 or 0xFF, the routines for accessing a serial EEPROM are used, at a maximum frequency of 4 Mbps. Otherwise, the routines for accessing a serial Flash are used, and they can run at faster speeds. Booting is performed through one of two sets of pins: * * Main set: BM[2-3], HA3, and HCS2, which allow use of the PLL. Alternate set: UTXD, URXD, SDA, and SCL, which cannot be used with the PLL. In either configuration, an error during SPI boot is flagged on the EVNT3 pin. For details on the boot procedure, see the "Boot Program" chapter of the MSC711x Reference Manual. MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 53 Hardware Design Considerations 3.5 DDR Memory System Guidelines MSC7116 devices contain a memory controller that provides a glueless interface to external double data rate (DDR) SDRAM memory modules with Class 2 Series Stub Termination Logic 2.5 V (SSTL_2). There are two termination techniques, as shown in Figure 36. Technique B is the most popular termination technique. VTT Generator VTT Controller RS DDR Bank RT SSTL_2 Address Command SSTL_2 Chip Selects RS Data Strobes Mask RT SSTL_2 VTT Terminator Technique A DDR Bank VREF VTT Generator Controller RS Technique B Chip Selects Data Strobes Mask DDR Bank RT SSTL_2 SSTL_2 RS RT VTT Terminator Island Address Command DDR Bank SSTL_2 Figure 36. SSTL Termination Techniques Figure 37 illustrates the power wattage for the resistors. Typical values for the resistors are as follows: * * RS = 22 RT = 24 MSC7116 Data Sheet, Rev. 13 54 Freescale Semiconductor Hardware Design Considerations VTT Driver VDDQ RT Receiver RS VREF VSS Figure 37. SSTL Power Value 3.5.1 VREF and VTT Design Constraints VTT and VREF are isolated power supplies at the same voltage, with VTT as a high current power source. This section outlines the voltage supply design needs and goals: * * * * * * * 3.5.2 Minimize the noise on both rails. VTT must track variation in the VREF DC offsets. Although they are isolated supplies, one possible solution is to use a single IC to generate both signals. Both references should have minimal drift over temperature and source supply. It is important to minimize the noise from coupling onto VREF as follows: -- Isolate VREF and shield it with a ground trace. -- Use 15-20 mm track. -- Use 20-30 mm clearance between other traces for isolating. -- Use the outer layer route when possible. -- Use distributed decoupling to localize transient currents and return path and decouple with an inductance less than 3 nH. Max source/sink transient currents of up to 1.8 A for a 32-bit data bus. Use a wide island trace on the outer layer: -- Place the island at the end of the bus. -- Decouple both ends of the bus. -- Use distributed decoupling across the island. -- Place SSTL termination resistors inside the VTT island and ensure a good, solid connection. Place the VTT regulator as closely as possible to the termination island. -- Reduce inductance and return path. -- Tie current sense pin at the midpoint of the island. Decoupling The DDR decoupling considerations are as follows: * * * * * DDR memory requires significantly more burst current than previous SDRAMs. In the worst case, up to 64 drivers may be switching states. Pay special attention and decouple discrete ICs per manufacturer guidelines. Leverage VTT island topology to minimize the number of capacitors required to supply the burst current needs of the termination rail. See the Micron DesignLine publication entitled Decoupling Capacitor Calculation for a DDR Memory Channel (http://download.micron.com/pdf/pubs/designline/3Q00dl1-4.pdf). MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 55 Hardware Design Considerations 3.5.3 General Routing The general routing considerations for the DDR are as follows: * * * * * * 3.5.4 All DDR signals must be routed next to a solid reference: -- For data, next to solid ground planes. -- For address/command, power planes if necessary. All DDR signals must be impedance controlled. This is system dependent, but typical values are 50-60 ohm. Minimize other cross-talk opportunities. As possible, maintain at least a four times the trace width spacing between all DDR signals to non-DDR signals. Keep the number of vias to a minimum to eliminate additional stubs and capacitance. Signal group routing priorities are as follows: -- DDR clocks. -- Route MVTT/MVREF. -- Data group. -- Command/address. Minimize data bit jitter by trace matching. Routing Clock Distribution The DDR clock distribution considerations are as follows: * * * * * 3.5.5 DDR controller supports six clock pairs: -- 2 DIMM modules. -- Up to 36 discrete chips. For route traces as for any other differential signals: -- Maintain proper difference pair spacing. -- Match pair traces within 25 mm. Match all clock traces to within 100 mm. Keep all clocks equally loaded in the system. Route clocks on inner critical layers. Data Routing The DDR data routing considerations are as follows: * * * * * * * Route each data group (8-bits data + DQS + DM) on the same layer. Avoid switching layers within a byte group. Take care to match trace lengths, which is extremely important. To make trace matching easier, let adjacent groups be routed on alternate critical layers. Pin swap bits within a byte group to facilitate routing (discrete case). Tight trace matching is recommended within the DDR data group. Keep each 8-bit datum and its DM signal within 25 mm of its respective strobe. Minimize lengths across the entire DDR channel: -- Between all groups maintain a delta of no more than 500 mm. -- Allows greater flexibility in the design for readjustments as needed. DDR data group separation: -- If stack-up allows, keep DDR data groups away from the address and control nets. -- Route address and control on separate critical layers. -- If resistor networks (RNs) are used, attempt to keep data and command lines in separate packages. MSC7116 Data Sheet, Rev. 13 56 Freescale Semiconductor Ordering Information 3.6 Connectivity Guidelines This section summarizes the connections and special conditions, such as pull-up or pull-down resistors, for the MSC7116 device. Following are guidelines for signal groups and configuration settings: * * * * * * * Clock and reset signals. -- SWTE is used to configure the MSC7116 device and is sampled on the deassertion of PORESET, so it should be tied to VDDC or GND either directly or through pull-up or pull-down resistors until PORESET is deasserted. After PORESET, this signal can be left floating. -- BM[0-1] configure the MSC7116 device and are sampled until PORESET is deasserted, so they should be tied to VDDIO or GND either directly or through pull-up or pull-down resistors. -- HRESET should be pulled up. Interrupt signals. When used, IRQ pins must be pulled up. HDI16 signals. -- When they are configured for open-drain, the HREQ/HREQ or HTRQ/HTRQ signals require a pull-up resistor. However, these pins are also sampled at power-on reset to determine the HDI16 boot mode and may need to be pulled down. When these pins must be pulled down on reset and pulled up otherwise, a buffer can be used with the HRESET signal as the enable. -- When the device boots through the HDI16, the HDDS, HDSP and H8BIT pins should be pulled up or down, depending on the required boot mode settings. Ethernet MAC/TDM2 signals. The MDIO signal requires an external pull-up resistor. I2C signals. The SCL and SDA signals, when programmed for I2C, requires an external pull-up resistor. General-purpose I/O (GPIO) signals. An unused GPIO pin can be disconnected. After boot, program it as an output pin. Other signals. -- The TEST0 pin must be connected to ground. -- The TPSEL pin should be pulled up to enable debug access via the EOnCE port and pulled down for boundary scan. -- Pins labelled NO CONNECT (NC) must not be connected. -- When a 16-pin double data rate (DDR) interface is used, the 16 unused data pins should be no connects (floating) if the used lines are terminated. -- Do not connect DBREQ to DONE (as you would for the MSC8101 device). Connect DONE to one of the EVNT pins, and DBREQ to HRRQ. 4 Ordering Information Consult a Freescale Semiconductor sales office or authorized distributor to determine product availability and place an order. Part Supply Voltage Package Type MSC7116 1.2 V core 2.5 V memory 3.3 V I/O Molded Array Process-Ball Grid Array (MAP-BGA) Pin Count Core Frequency (MHz) Solder Spheres Order Number 400 266 Lead-free MSC7116VM1000 Lead-bearing MSC7116VF1000 MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 57 Package Information 5 Package Information Notes: 1. All dimensions in millimeters. 2. Dimensioning and tolerancing per ASME Y14.5M-1994. 3. Maximum solder ball diameter measured parallel to Datum A. 4. Datum A, the seating plane, is determined by the spherical crowns of the solder balls. 5. Parallelism measurement shall exclude any effect of mark on top surface of package. CASE 1568-01 Figure 38. MSC7116 Mechanical Information, 400-pin MAP-BGA Package 6 Product Documentation * * * MSC711x Reference Manual (MSC711xRM). Includes functional descriptions of the extended cores and all the internal subsystems including configuration and programming information. Application Notes. Cover various programming topics related to the StarCore DSP core and the MSC7116 device. SC140/SC1400 DSP Core Reference Manual. Covers the SC140 and SC1400 core architecture, control registers, clock registers, program control, and instruction set. MSC7116 Data Sheet, Rev. 13 58 Freescale Semiconductor Revision History 7 Revision History Table 36 provides a revision history for this data sheet. Table 36. Document Revision History Revision Date Description 0 Apr 2004 * Initial public release. 1 May 2004 * Added ordering information and new package options. 2 Aug. 2004 * Updated clock parameter values. * Updated DDR timing specifications. * Updated I2C timing specifications. 3 Sep. 2004 * Updated Figures 1-2 and 1-2 to correct HDSP and DBREQ. * Corrected EE0 port reference. * Updated ball location for HDSP. 4 Jan. 2005 * Added signal HA3. * Updated absolute maximum ratings, DDR DRAM capacitance specifications, clock parameters, reset timing, and TDM timing. * Added note for timing reference for I2C interface. * Expanded GPIO timing information. * Corrected pin T20 and K20 signal designation. * Corrected signal names to GPAO15 and IRQ2. * Expanded design guidelines in Chapter 4. 5 Mar. 2005 * * * * * 6 Apr. 2005 * Added recommended power supply ratings and updated equations to estimate power consumption. 7 Oct. 2005 * Updated core and total power consumption examples. 8 Dec. 2005 * Added information about the new mask set 1M88B. Affected all sections. 9 Nov. 2006 * Updated arrows in Host DMA Writing Timing figure. * Updated boot overview in Section 4.4.3. 10 Apr. 2007 * Removed erroneous references to VCCSYN and VCCSYN1. 11 Jul. 2007 * * * * * * 12 Aug 2007 * The power-up and power-down sequences described in Section 3.2 starting on page 42 have been expanded to five possible design scenarios/cases. These cases replace the previously recommended power-up/power-down sequence recommendations. Section 3.2 has been clarified by adding subsection headings. 13 Apr 2008 * Change the PLL filter resistor from 20 to 2 in Section 3.2.5. Updated features list. Updated power specifications. Changed CLKIN frequency range. Added clock configuration information. Updated JTAG timings. Updated to new data sheet format. Reorganized and renumbered sections, figures, and tables. Removed all references to obsolete mask set 1L44X and corresponding specification values. Added a note to clarify the definition of TCK timing 700 in new Table 31. Reworked reset and boot sections. Expanded I2C boot information and added SPI boot information. Removed obsolete part numbers. MSC7116 Data Sheet, Rev. 13 Freescale Semiconductor 59 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 +1-800 441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com Document Number: MSC7116 Rev. 13 4/2008 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. FreescaleTM, the Freescale logo, CodeWarrior, fieldBIST, and StarCore are trademarks of Freescale Semiconductor, Inc. IEEE, 802.3, 802.3u, 802.3x, and 802.3ac are trademarks of the Institute of Electrical and Electronics Engineers, Inc. (IEEE). All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2004, 2008. All rights reserved.