SPX2945M3-L-3-3/TR - MaxLinear, Inc.

1

SPX2945

DESCRIPTION

FEATURES

■Output 3.3V, 5.0V at 400mA Output

■Very Low Quiescent Current, 100µA

■Low Dropout Voltage, 420mV at 400mA

■Extremely Tight Load and Line Regulation

■Very Low Temperature Coefficient

■Current & Thermal Limiting

■Error Flag Warns Of Output Dropout

■Logic-Controlled Electronic Shutdown

■Output Programmable From 1.24V to 20V

(for SO-8)

The SPX2945 is a low power voltage regulator. This device is an excellent choice for use in battery-powered

applications such as cordless telephones, radio control systems, and portable computers. The SPX2945

features very low quiescent current (100µA Typ.) and very low dropout voltage. This includes a tight initial

tolerance of 1% max and very low output temperature coefficient, making the SPX2945 useful as a low-

power voltage reference.

The error flag output feature is used as power-on reset for warning of a low output voltage, due to a falling

voltage input of batteries. Another feature is the logic-compatible shutdown input which enables the

regulator to be switched on and off. The SPX2945 is offered in 3-pin TO-220 package, SO-8 (same pin

out as SPX2951), SOT-223, surface mount 3-Pin TO-252, 3-Pin TO-263 packages and 5-Pin TO-263.

The regulator output voltage (of the 8-pin SO-8) may be pin-strapped for a 3.3V and 5.0V or programmed

from 1.24V to 20V with an external pair of resistors. Look for SPX2951 for 150mA and SPX2954 for 250mA

applications.

400mA Low Dropout Voltage Regulator with Shutdown

TO-220-3 (U)

123

V

IN

V

OU

GN

SPX2945

13254

SPX2945

5 Pin TO-263

Er

V

IN

GND

V

OUT

SD

132

SOT-223 (M3)

V

IN

GN V

OU

SPX2945

2

1

3

4

8

7

6

5

8-Pin Surface Mount

V

OU

SENS

SHUTDOWN

GN

V

IN

FEEDBACK

5V/ 3.3V TAP

ERRO

SPX2945

TO-252 (R)

123

V

IN

V

OU

GN

SPX2945

TO-263-5

V

IN

TO-263-3 (T)

V

OU

GN

SPX2945

3

2

1

(S)

(T5)

100K

ERROR

______

SD

V

OUT

GND

FB

+V

IN

0.01µF

3

81

4

7

SHUTDOWN

INPUT

SPX2945

OFF

ON

+V

IN

5

10µF

V

REF

R

2

R

1

+

ERROR

OUTPUT

1.2V to 20V

+2.2 µF

+

SPX2945

V

IN

5V

IN

GND

OUT

0.1 µF

Adjustable Regulator

5V Regulator Circuit

Now Available in Lead Free Packaging

Note: Tab is Ground

2

ELECTRICAL CHARACTERISTICS

Electrical characteristics at VIN = VO+1V, IO = 1mA, COUT = 2.2µF, TA = 25°C, unless otherwise specified. The ♦

denotes

the specifications wich apply over full operating tempeture range -40°C to +85°C, unless noted.

PARAMETER CONDITIONS MIN TYP MAX UNITS

(Note 2)

3.3V Version

Output Voltage 3.267 3.3 3.333 V

1mA ≤ IL ≤ 400mA 3.217 3.3 3.382 ♦

5.0V Version

Output Voltage 4.950 5.0 5.050 V

1mA ≤ IL ≤ 400mA 4.880 5.0 5.120 ♦

All Voltage Options

Output Voltage 20 100 ♦ ppm/°C

Temperature Coefficient (Note1)

Line Regulation (Note 3) 6V ≤ VIN ≤ 20V (Note 4) 1.5 20 ♦ mV

Load Regulation (Note 3) IL=1 to 400mA 6 20 mV

30 ♦

Dropout Voltage (Note5) IL=1mA 60 100 mV

150 ♦

IL=400mA 360 450

700 ♦

Ground Current IL=1mA 100 200 µA

300 ♦

IL=150mA 2 4 mA

6 ♦

IL=300mA 4 8

12 ♦

IL=400mA 8 15

25 ♦

Current Limit VOUT=0 330 800 ♦ mA

Thermal Regulation 0.05 0.2 %/W

Output Noise, 10Hz to 100kHz, CL=2.2µF 400 µVRMS

IL=100mA CL=33µF 260

PSRR at 100KHz 31 dB

IL=100mA CL=10µF

Adjustable 8 Pin Version only

Reference Voltage 1.210 1.235 1.260 V

Reference Voltage Over Temperature 1.185 1.285 V

Feedback Pin Bias Current 20 40 nA

60 ♦

Reference Voltage Temp. 20 ppm/°C

Coefficient

Power Dissipation ........................................................ Internally Limited

Lead Temp. (Soldering, 5 Seconds) ............................................. 260°C

Storage Temperature Range ........................................ -65°C to +150°C

Operating Junction Temperature Range ....................... -40°C to +125°C

Input Supply Voltage ......................................................... -20V to +26V

ABSOLUTE MAXIMUM RATINGS

Feedback Input Voltage ................................................ -1.5V to +26V

Shutdown Input Voltage ................................................ -0.3V to +26V

Error Comparator Output .............................................. -0.3V to +26V

ESD Rating ............................................................................ 2kV Min

3

PARAMETER CONDITIONS MIN TYP MAX ♦ UNITS

(Note 2)

Feedback Pin Bieas Current 0.1 nA/°C

Temperature Coefficient

Output Leakage Current V0H=20V 0.01 1 µA

2 ♦

Output Low Voltage VIN=4.5V 150 250 mV

I0L=400µA 400 ♦

Upper Threshold Voltage (Note 6) 40 60 mV

25

Lower Threshold Voltage (Note 6) 75 95 mV

140 ♦

Hysteresis (Note 6) 15 mV

Input Logic Voltage Low (Regulator ON) 0.7 ♦ V

High (Regulator OFF) 1.3 2.0 ♦

Shutdown Pin Input Current VS=2.4V 30 50 µA

100 ♦

VS=26V 450 600

750 ♦

Regulator Output Current (Note 7) 10 3 µA

in Shutdown 20 ♦

Thermal Resistance TO-220-3 29.4 ♦

Theta Junction-Ambient θJA TO-263-3 31.4 ♦°C/W

TO-263-5 31.2 ♦

NSOIC-8 128.4 ♦

SOT-223 62.3 ♦

TO-252 50 ♦

ELECTRICAL CHARACTERISTICS: Continued

Electrical characteristics at VIN = VO+1V, IO = 1mA, COUT = 2.2µF, TA = 25°C, unless otherwise specified. ♦ applies over the

full operating temperature range.

Note 1: Output or reference voltage temperature coefficients defined as the worst case voltage change divided by

the total temperature range.

Note 2: Unless otherwise specified all limits are guaranteed for Tj = 25°C, VIN = 6V, IL = 1mA and CL = 2.2µF. Additional

conditions for the 8-pin versions are feedback tied to 5V/3.3V tap and output tied to output sense (VOUT = 5V) and

VSHUTDOWN ≤ 0.8V.

Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes

in output voltage due to heating effects are covered under the specification for thermal regulation.

Note 4: Line regulation for the SPX2945 is tested at 150°C for IL = 1 mA. For TJ = 125°C, line regulation is guaranteed

by design.

Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below

its nominal value measured at 1V differential at very low values of programmed output voltage, the minimum input

supply voltage of 2V ( 2.3V over temperature) must be taken into account.

Note 6: Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the

nominal reference voltage measured at 6V input. To express these thresholds in terms of output voltage change,

multiply by the error amplifier gain = VOUT/VREF = (R1 + R2)/R2. For example, at a programmed output voltage of 5V,

the Error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds remain

constant as a percent of VOUT as VOUT is varied, with the dropout warning occurring at typically 5% below nominal, 7.5%

guaranteed.

Note 7: VSHUTDOWN ≥ 2V, VIN ≤ 26V, VOUT = 0, Feedback pin tied to 5V/3.3V Tap.

4

SPX2945 - 5.0V BLOCK DIAGRAM

FEEDBACK INPUT OUTPUT

UNREGULATED DC

SHUTDOWN

GROUND

ERROR

______

5V TAP

SENSE

5V at 400mA

MAX

TO CMOS OR

TTL

REFERENCE

ERROR DETECTION

COMPARATOR

ERROR

AMPLIFIER

1.23V

FROM

CMOS OR

TTL

+

60 mV

3

781

2

6

5

4

.

60kΩ

330kΩ

180kΩ

.

1µF

_

External Capacitors

The stability of the SPX2945 requires a 2.2µF or

greater capacitor between output and ground.

Oscillation could occur without this capacitor.

Most types of tantalum or aluminum electrolytic

works fine here. For operations of below -25°C

solid tantalum is recommended since the many

aluminum types have electrolytes that freeze at

about -30°C. The ESR of about 5Ω or less and

resonant frequency above 500kHz are the most

important parameters in the value of the capaci-

tor. The capacitor value can be increased with-

out limit.

At lower values of output current, less output

capacitance is required for stability. For the

currents below 10mA the value of the capacitor

can be reduced to 0.5µF and 0.15µF for 1mA.

More output capacitance needed for the 8-pin

version at voltages below 5V since it runs the

error amplifier at lower gain. At worst case

4.7µF or greater must be used for the condition

of 250mA load at 1.23V output.

The SPX2945, unlike other low dropout regu-

lators will remain stable and in regulation with

no load in addition to the internal voltage di-

vider. This feature is especially important in

applications like CMOS RAM keep-alive.

If there is more than 10 inches of wire between

the input and the AC filter capacitor, or if a

battery is used as the input, then a 0.1µF tanta-

lum or aluminum electrolytic capacitor should

be placed from the input to the ground.

Instability can occur if there is stray capaci-

tance to the SPX2945 feedback terminal (pin 7).

This could cause more problems when using a

higher value of external resistors to set the

output voltage.

This problem can be fixed by adding a 100pF

capacitor between output and feedback and

increasing the output capacitor to at least 3.3µF.

APPLICATION INFORMATION

5

Error Detection Comparator Output

The Comparator produces a logic low output

whenever the SPX2945 output falls out of regu-

lation by more than around 5%. This is around

60mV offset divided by the 1.235 reference

voltage. This trip level remains 5% below

normal regardless of the programmed output

voltage of the regulator. Figure 1 shows the

timing diagram depicting the ERROR signal

and the regulator output voltage as the SPX2945

input is ramped up and down. The ERROR

signal becomes low at around 1.3V input, and

goes high around 5V input (input voltage at

which VOUT = 4.75). Since the SPX2945’s

dropout voltage is load dependent, the input

voltage trip point (around 5V) will vary with the

load current. The output voltage trip point

(approx. 4.75V) does not vary with load.

The error comparator has an open-collector out-

put, which requires an external pull-up resistor.

Depending on the system requirements the re-

sistor may be returned to 5V output or other

supply voltage. In determining the value of this

resistor, note that the output is rated to sink

400µA; this value adds to battery drain in a low

battery condition. Suggested values range from

100K to 1MΩ. If the output is unused this

resistor is not required.

Programming the Output Voltage of

SPX2945

The SPX2945 may be pin-strapped for 5V or

3.3V using its internal voltage divider by tying

Pin 1 (output) to Pin 2 (sense) and Pin 7 (feed-

back) to Pin 6 (5V/3.3V Tap).

Also, it may be programmed for any output

voltage between its 1.235V reference and its

20V maximum rating. As seen in Figure 2, an

external pair of resistors is required.

Refer to the below equation for the program-

ming of the output voltage::

VOUT = VREF x ( 1 + R1/ R2 )+ IFBR1

The VREF is 1.235 and IFB is the feedback bias

current, nominally -20nA. The minimum rec-

ommended load current of 1 µA forces an upper

limit of 1.2 MΩ on value of R2. If no load is

presented the IFB produces an error of typically

2% in VOUT, which may be eliminated at room

temperature by trimming R1. To improve the

accuracy choose the value of R2 = 100k; this

reduces the error by 0.17% and increases the

resistor program current by 12µA. Since the

SPX2945 typically draws 60 µA at no load with

Pin 2 open-circuited this is a small price to pay.

Reducing Output Noise

It may be an advantage to reduce the AC noise

present at the output. One way is to reduce the

regulator bandwidth by increasing the size of

the output capacitor. This is the only way that

noise can be reduced on the 3 lead SPX2945 but

is relatively inefficient, as increasing the ca-

pacitor from 1µF to 220µF only decreases the

noise from 430µV to 160µV Vrms for a 100kHz

bandwidth at 5V output. Noise could also be

reduced fourfold by a bypass capacitor across

R1, since it reduces the high frequency gain from

4 to unity. Pick

CBYPASS ≅1 / 2πR1 x 200 Hz

or choose 0.01µF. When doing this, the output

capacitor must be increased to 3.3µF to main-

tain stability. These changes reduce the output

noise from 430µV to 100µV Vrms for a 100kHz

bandwidth at 5V output. With the bypass ca-

pacitor added, noise no longer scales with out-

put voltage so that improvements are more dra-

matic at higher output voltages.

+

4.75V

OUTPUT

VOLTAGE

ERROR*

_______

INPUT

VOLTAGE 1.3V

5.0V

* See Application Info.

Figure 1. ERROR Output Timing

6

PACKAGE: 3 PIN TO-252

FRONT VIEW

b3

E

D

L3

123

L4

e

b2

b

L5

BACK VIEW

E1

D1

H

(L1)

Seating Plane

c

C2

A

SIDE VIEW

Gauge

Plane

L

L2

θ1

θ

A1

MIN NOM MAX MIN NOM MAX

A0.086 - 0.094 2.18 - 2.39

A1 --0.005 - - 0.13

b0.025 - 0.035 0.64 - 0.89

b2 0.030 - 0.045 0.76 - 1.14

b3 0.195 - 0.215 4.95 - 5.46

c0.018 - 0.024 0.46 - 0.61

c2 0.018 - 0.035 0.46 - 0.89

D0.235 0.240 0.245 5.97 6.10 6.22

D1 0.205 - - 5.21 - -

E0.250 - 0.265 6.35 - 6.73

E1 0.170 - - 4.32 - -

e

H0.370 - 0.410 9.4 - 10.41

L0.055 0.060 0.070 1.4 1.52 1.78

L1

L2

L3 0.035 - 0.050 0.89 - 1.27

L4 --0.040 - - 1.02

L5 0.045 - 0.060 1.14 - 1.52

ø0º - 10º 0º - 10º

ø1 0º - 15º 0º - 15º

0.51 BSC

2.74 REF

2.29 BSC

SYMBOL

3 Pin TO-252 JEDEC TO-252 Variation AA

SIPEX Pkg Signoff Date/Rev: JL Aug4-05/Rev A

.090 BSC

.108 REF

.020 BSC

Dimensions in Inches:

Controlling Dimension

Dimensions in Millimeters

Conversion Factor:

1 Inch = 25.40 mm

7

PACKAGE: 3 PIN TO-220

MIN NOM MAX MIN NOM MAX

A 0.140 - 0.190 3.56 - 4.83

A1 0.020 - 0.055 0.51 - 1.27

A2 0.080 - 0.115 2.03 - 2.79

b 0.015 0.027 0.040 0.25 0.51 1.02

b2 0.045 0.057 0.070 1.14 1.45 1.78

c 0.014 - 0.024 0.25 - 0.51

D 0.560 - 0.650 14.22 - 16.51

D1 0.330 - 0.355 8.38 - 8.89

D2 0.480 - 0.507 12.19 - 12.70

E 0.380 - 0.420 9.65 - 10.67

E1 0.270 - 0.350 6.86 - 8.89

E2 - - 0.030 - - 0.76

e

e1

H1 0.230 - 0.270 5.84 - 6.86

L 0.500 - 0.580 12.70 - 14.73

L1 - - 0.250 - - 6.35

ΦP0.139 - 0.161 3.30 - 4.06

Q 0.100 - 0.135 2.54 - 3.30

SIPEX Pkg Signoff Date/Rev: JL Aug4-05 / Rev A

3 Pin TO-220 JEDEC TO-220 Variation AB

SYMBOL

2.54 BSC

5.08 BSC

Dimensions in Inches:

Controlling Dimension

Dimensions in Millimeters:

Conversion Factor:

1 Inch = 25.40 mm

.100 BSC

.200 BSC

D2

(H1)

E1

Thermal

Pad

BACK

VIEW

e1

b2

E

øP

Q

D

D1

E2

L

L1

b

1

e

FRONT

VIEW

H1

Seating

Plane

A1

A

Chamfer

Optional

C

A2

SIDE

VIEW

8

PACKAGE: 5 PIN TO-263

(L1)

E1

D1

Thermal

Pad

BACK VIEW

E

D

L1

e

b

123

E/2

FRONT VIEW

45

DETAIL C

L

Gauge Plane

A1

Seating

Plane

L3

θ

c

C2

A

H

Seating

Plane

See Detail C

Chamfer

Optional

SIDE VIEW

SYMBOL MIN NOM MAX MIN NOM MAX

A0.160 - 0.190 4.06 - 4.83

A1 0.000 - 0.010 0.00 - 0.25

b0.020 - 0.039 0.51 - 0.99

c0.015 - 0.029 0.38 - 0.74

c2 0.045 - 0.065 11.43 - 5.84

D0.330 - 0.380 8.38 - 9.65

D1 0.270 - - 6.86 - -

E0.380 - 0.420 9.65 - 10.67

E1 0.245 - - 6.22 - -

e

H0.575 - 0.625 14.61 - 15.88

L0.070 - 0.110 1.78 - 2.79

L1 - - 0.066 - - 1.68

L3

O0˚ - 8˚ 0˚ - 8˚

SIPEX Pkg Signoff Date/Rev: JL Jan18-06/Rev A

.010 BSC 2.54 BSC

Inches

Controlling Dimension

Millimeters

Conversion Factor:

1 Inch = 25.40 mm

5 Pin TO-263 JEDEC TO-263 Variation BA

.067 BSC 17.02 BSC

9

PACKAGE: 3 PIN TO-263

MIN NOM MAX MIN NOM MAX

A 0.160 - 0.190 4.06 - 4.83

A1 0.000 - 0.010 0.00 - 0.25

b 0.020 - 0.039 0.51 - 0.99

b2 0.045 - 0.070 1.14 - 1.78

c 0.015 - 0.029 0.38 - 0.74

c2 0.045 - 0.065 1.14 - 1.65

D 0.330 - 0.380 8.38 - 9.65

D1 0.270 - - 6.86 - -

E 0.380 - 0.420 9.65 - 10.67

E1 0.245 - - 6.22 - -

e

H 0.575 - 0.625 14.61 - 15.88

L 0.070 - 0.110 1.78 - 2.79

L1 - - 0.066 - - 1.68

L3

O0˚ - 8˚ 0˚ - 8˚

Inches

Controlling Dimension

Millimeters

Conversion Factor:

1 Inch = 25.40 mm

SIPEX Pkg Signoff Date/Rev: JL Aug5-05 / Rev A

0.25 BSC.010 BSC

SYMBOL

3 Pin TO-263 JEDEC TO-263 Variation AA

2.54 BSC.100 BSC

DETAIL C

L

Gauge Plane

A1

Seating

Plane

L3

θ

c

C2

A

H

Seating

Plane

Chamfer

Optional

SIDE VIEW

See Detail C

E1

D1

(L1)

Thermal

Pad

BACK

VIEW

L1

FRONT VIEW

E

D

b2

e

b

E/2

1 2 3

10

PACKAGE: 3 PIN SOT-223

E

D

1

e

E1

b2

b

TOP VIEW

22 3

e1

FRONT VIEW

L

Gauge Plane

Seating Plane

L2

c

ø

A1

A2

A

SYMBOL MIN NOM MAX MIN NOM MAX

A--1.80 - - 0.071

A1 0.02 - 0.10 0.001 - 0.004

A2 1.50 1.60 1.70 0.060 0.063 0.067

b0.66 0.76 0.84 0.026 0.030 0.033

b2 2.90 3.00 3.10 0.114 0.118 0.122

c0.23 0.30 0.35 0.010 0.012 0.014

D6.30 6.50 6.70 0.248 0.256 0.264

E6.70 7.00 7.30 0.264 0.276 0.287

E1 3.30 3.50 3.70 0.130 0.138 0.146

e

e1

L0.75 - - 0.030 - -

L2

ø0º - 10º 0º - 10º

0.091 BASIC

0.182 BASIC

0.010 BASIC

3 Pin SOT-223 JEDEC TO-261 Variation AA

SIPEX Pkg Signoff Date/Rev: JL Aug8-05/Rev A

Millimeters

Controlling Dimension

Inches

Conversion Factor:

1 Inch = 25.40 mm

0.25 BASIC

2.30 BASIC

4.60 BASIC

11

PACKAGE: 8 PIN NSOIC

FRONT VIEW

L

ø1

Gauge Plane

L2

c

R

R1

ø2

ø

Seating

Plane

h

ø1

D

E

E/2

3

2

1

b

e

E1

E1/2

6

8

Pin1 Designator

to be within this

INDEX AREA

(D/2 x E1/2)

TOP VIEW

(L1)

5

4

7

D/2

AA2

A1

SIDE VIEW

Seating Plane

MIN NOM MAX MIN NOM MAX

A 1.35 - 1.75 0.053 - 0.069

A1 0.10 - 0.25 0.004 - 0.010

A2 1.25 - 1.65 0.049 - 0.065

b 0.31 - 0.51 0.012 - 0.020

c 0.17 - 0.25 0.007 - 0.010

E

E1

e

h 0.25 0.50 0.010 - 0.020

L 0.40 - 1.27 0.016 - 0.050

L1

L2

R 0.07 - - 0.003 - -

R1 0.07 - - 0.003 - -

ø0º-8º0º - 8º

ø1 5º - 15º 5º - 15º

ø2 0º - - 0º - -

D

0.041 REF

SIPEX Pkg Signoff Date/Rev: JL Aug16-05 / Rev A

4.90 BSC

6.00 BSC

3.90 BSC

1.27 BSC

1.04 REF

0.193 BSC

0.25 BSC 0.010 BSC

0.236 BSC

0.050 BSC

0.154 BSC

8 Pin NSOIC JEDEC MS-012 Variation AA

SYMBOL Dimensions in Millimeters:

Controlling Dimension

Dimensions in Inches

Conversion Factor:

1 Inch = 25.40 mm

12

ORDERING INFORMATION

Available in lead free packaging. To order add "-L" suffix to part number.

Example: SPX2954S-5-0/TR = standard; SPX2954S-L-5-0/TR = lead free

/TR = Tape and Reel

Pack quantity is 500 for TO-263, 2,000 for TO-252, and 2,500 for SOT223 or NSOIC.

Ordering No. Accuracy Output Voltage Packages

SPX2945M3-3-3 1% 3.3V 3-Pin SOT-223

SPX2945M3-3-3/TR 1% 3.3V 3-Pin SOT-223

SPX2945M3-5-0 1% 5.0V 3-Pin SOT-223

SPX2945M3-5-0/TR 1% 5.0V 3-Pin SOT-223

SPX2945S-3-3 1% 3.3V 8-Pin NSOIC

SPX2945S-3-3/TR 1% 3.3V 8-Pin NSOIC

SPX2945S-5-0 1% 5.0V 8-Pin NSOIC

SPX2945S-5-0/TR 1% 5.0V 8-Pin NSOIC

SPX2945R-3-3 1% 3.3V 3-Pin TO-252

SPX2945R-3-3/TR 1% 3.3V 3-Pin TO-252

SPX2945R-5-0 1% 5.0V 3-Pin TO-252

SPX2945R-5-0/TR 1% 5.0V 3-Pin TO-252

SPX2945T-3-3 1% 3.3V 3-Pin TO-263

SPX2945T-3-3/TR 1% 3.3V 3-Pin TO-263

SPX2945T-5-0 1% 5.0V 3-Pin TO-263

SPX2945T-5-0/TR 1% 5.0V 3-Pin TO-263

SPX2945T5-3-3 1% 3.3V 5-Pin TO-263

SPX2945T5-3-3/TR 1% 3.3V 5-Pin TO-263

SPX2945T5-5-0 1% 5.0V 5-Pin TO-263

SPX2945T5-5-0/TR 1% 5.0V 5-Pin TO-263

SPX2945U-3-3 1% 3.3V 3-Pin TO-220

SPX2945U-5-0 1% 5.0V 3-Pin TO-220

Sipex Corporation

Headquarters and

Sales Office

233 South Hillview Drive

Milpitas, CA 95035

TEL: (408) 934-7500

FAX: (408) 935-7600

Solved By SipexTM

Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the

application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.