DS34LV87T DS34LV87T Enhanced CMOS Quad Differential Line Driver Literature Number: SNLS116C DS34LV87T Enhanced CMOS Quad Differential Line Driver General Description Features The DS34LV87T is a high speed quad differential CMOS driver that meets the requirements of both TIA/EIA-422-B and ITU-T V.11. The CMOS DS34LV87T features low static ICC of 100 A max which makes it ideal for battery powered and power conscious applications. The TRI-STATE (R) enable, EN, allows the device to be disabled when the device is not in use to minimize power. The dual enable scheme allows for flexibility in turning devices on or off. Protection diodes protect all the driver inputs against electrostatic discharge. The driver and enable inputs (DI and EN) are compatible with LVTTL and LVCMOS devices. Differential outputs have the same VOD (2V) guarantee as the 5V version. The outputs have enhanced ESD Protection providing greater than 7 kV tolerance. n Meets TIA/EIA-422-B (RS-422) and ITU-T V.11 recommendation n Interoperable with existing 5V RS-422 networks n Guaranteed VOD of 2V min over operating conditions n Balanced output crossover for low EMI (typical within 40 mV of 50% voltage level) n Low power design (330 W @ 3.3V static) n ESD 7 kV on cable I/O pins (HBM) n Industrial temperature range n Guaranteed AC parameter: -- Maximum driver skew: 2 ns -- Maximum transition time: 10 ns n Pin compatible with DS26C31 n Available in SOIC packaging Connection Diagram Truth Table Dual-In-Line Package Enables Input EN DI DO+ Outputs DO- L X Z Z H H H L H L L H L = Low logic state X = Irrelevant H = High logic state Z = TRI-STATE 01264501 Top View Order Number DS34LV87TM See NS Package Number M16A TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2004 National Semiconductor Corporation DS012645 www.national.com DS34LV87T Enhanced CMOS Quad Differential Line Driver November 2000 DS34LV87T Absolute Maximum Ratings (Note 1) Lead Temperature Range If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Ratings Supply Voltage (VCC) (Soldering, 4 sec.) (HBM, 1.5k, 100 pF) -0.5V to +7V Enable Input Voltage (EN) -0.5V to VCC + 0.5V Driver Input Voltage (DI) -0.5V to VCC + 0.5V Recommended Operating Conditions -0.5V to +7V Supply Voltage (VCC) Maximum Package Power Dissipation @+25C M Package Typ Max Units 3.0 3.3 3.6 V -40 25 +85 C 500 ns Temperature Range (TA) 9.8 mW/C above +25C Storage Temperature Range Min Operating Free Air 1226 mW Derate M Package 2.5 kV Other Pins Driver Output Voltage (Power Off: DO+, DO-) 7 kV Driver Outputs 20 mA 150 mA Clamp Diode Current DC Output Current, per pin +260C DS34LV87T Input Rise and Fall Time -65C to +150C Electrical Characteristics (Notes 2, 3) Over Supply Voltage and Operating Temperature ranges, unless otherwise specified Symbol Parameter Conditions Pin VOD1 Output Differential Voltage RL= , (No Load) DO+, VOD2 Output Differential Voltage RL = 100 Figure 1 DO- VOD2 Change in Magnitude of Min Typ Max Units 3.3 4.0 V 2 2.6 -400 7 400 mV V 3.2 3.5 V Output Differential Voltage VOD3 Output Differential Voltage RL = 3900 (V.11), Figure 1 (Note 7) VOC Common Mode Voltage RL = 100 Figure 1 VOC Change in Magnitude of -400 1.5 2 V 6 400 mV 0.5 20 A -70 -150 mA Common Mode Voltage IOZ TRI-STATE Leakage VOUT = VCC or GND Current Drivers Disabled ISC Output Short Circuit Current VOUT = 0V VIN = VCC or GND (Note 4) IOFF Output Leakage Current VCC= 0V, VOUT = 3V 0.03 100 A VCC = 0V, VOUT = -0.25V -0.08 -100 A -40 VIH High Level Input Voltage DI, 2.0 VCC V VIL Low Level Input Voltage EN GND 0.8 V IIH High Level Input Current VIN= VCC IIL Low Level Input Current VIN = GND VCL Input Clamp Voltage IIN = -18 mA ICC Power Supply Current No Load, VIN (all) = VCC or GND www.national.com 10 -10 2 VCC A A -1.5 V 100 A Over Supply Voltage and Operating Temperature ranges, unless otherwise specified Symbol tPHLD Parameter Conditions Differential Propagation Delay RL = 100, CL = 50 pF (Figures 2, 3) High to Low tPLHD Differential Propagation Delay Min Typ Max Units 6 10.5 16 ns 6 11 16 ns 0.5 2.0 ns Low to High tSKD Differential Skew |tPHLD-tPLHD| tSK1 Skew, Pin to Pin (same device) 1.0 2.0 ns tSK2 Skew, Part to Part (Note 8) 3.0 5.0 ns tTLH Differential Transition Time 4.2 10 ns 4.7 10 ns Low to High (20% to 80%) tTHL Differential Transition Time High to Low (80% to 20%) tPHZ Disable Time High to Z 12 20 ns tPLZ Disable Time Low to Z 9 20 ns tPZH Enable Time Z to High 22 32 ns tPZL Enable Time Z to Low 22 32 fMAX Maximum Operating Frequency 32 (Figures 4, 5 ) ns MHz (Note 9) Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except differential voltages VOD1, VOD2, VOD3. Note 3: All typical values are given for VCC= 3.3V and TA = +25C. Note 4: Only one output shorted at a time. The output (true or complement) is configured High. Note 5: f = 1 MHz, tr and tf 6 ns (10% to 90%). Note 6: See TIA/EIA-422-B specifications for exact test conditions. Note 7: This specification limit is for compliance with TIA/EIA-422-B and ITU-T V.11. Note 8: Devices are at the same VCC and within 5C within the operating temperature range. Note 9: All channels switching, output duty cycle criteria is 40%/60% measured at 50%. This parameter is guaranteed by design and characterization. Parameter Measurement Information 01264502 FIGURE 1. Differential Driver DC Test Circuit 3 www.national.com DS34LV87T Switching Characteristics (Notes 5, 6) DS34LV87T Parameter Measurement Information (Continued) 01264503 FIGURE 2. Differential Driver Propagation Delay and Transition Time Test Circuit 01264504 FIGURE 3. Differential Driver Propagation Delay and Transition Time Waveforms Note 10: Generator waveform for all tests unless otherwise specified: f = 1 MHz, Duty Cycle = 50%, Zo = 50, tr 10 ns, tf 10 ns. Note 11: CL includes probe and fixture capacitance. 01264505 FIGURE 4. Driver Single-Ended TRI-STATE Test Circuit www.national.com 4 DS34LV87T Parameter Measurement Information (Continued) 01264506 FIGURE 5. Driver Single-Ended TRI-STATE Waveforms Power Decoupling Recommendations: Bypass caps must be used on power pins. High frequency ceramic (surface mount is recommended) 0.1 F in parallel with 0.01 F at the power supply pin. A 10 F or greater tantalum or electrolytic should be connected at the power entry point on the printed circuit board. Typical Application Information General application guidelines and hints for differential drivers and receivers may be found in the following application notes: AN-214, AN-457, AN-805, AN-847, AN-903, AN-912, AN-916. 01264507 RT is optional although highly recommended to reduce reflection 01264508 FIGURE 6. Typical Driver Connection 5 www.national.com DS34LV87T Typical Application Information (Continued) 01264509 FIGURE 7. Typical Driver Output Waveforms www.national.com 6 DS34LV87T Enhanced CMOS Quad Differential Line Driver Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead Molded Small Outline Package (M) Order Number DS34LV87TM NS Package Number M16A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated