Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Overview KEMET's X7R dielectric features a 125C maximum operating temperature and is considered "temperature stable." The Electronics Components, Assemblies & Materials Association (EIA) characterizes X7R dielectric as a Class II material. Components of this classification are fixed, ceramic dielectric capacitors suited for bypass and decoupling applications or for frequency discriminating circuits where Q and stability of capacitance characteristics are not critical. X7R exhibits a predictable change in capacitance with respect to time and voltage and boasts a minimal change in capacitance with reference to ambient temperature. Capacitance change is limited to 15% from -55C to +125C. Benefits Applications * * * * Typical applications include decoupling, bypass, filtering and transient voltage suppression. * * * * * * -55C to +125C operating temperature range Pb-Free and RoHS Compliant Temperature stable dielectric EIA 0402, 0603, 0805, 1206, 1210, 1808, 1812, 1825, 2220, and 2225 case sizes DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V, 200 V, and 250 V Capacitance offerings ranging from 10 pF to 47 F Available capacitance tolerances of 5%, 10%, and 20% Non-polar device, minimizing installation concerns 100% pure matte tin-plated termination finish allowing for excellent solderability SnPb termination finish option available upon request (5% minimum) Ordering Information C 1206 C 106 M 4 R Ceramic Case Size (L" x W") Specification/ Series1 Capacitance Code (pF) Capacitance Tolerance Voltage Dielectric 0402 0603 0805 1206 1210 1808 1812 1825 2220 2225 C = Standard 2 Significant Digits + Number of Zeros J = 5% K = 10% M = 20% 9 = 6.3 V 8 = 10 V 4 = 16 V 3 = 25 V 6 = 35 V 5 = 50 V 1 = 100 V 2 = 200 V A = 250 V R = X7R A C TU Failure Rate/ Termination Finish2 Design A = N/A C = 100% Matte Sn Packaging/Grade (C-Spec)3 Blank = Bulk TU = 7" Reel Unmarked TM = 7" Reel Marked Flexible termination option is available. Please see FT-CAP product bulletin C1013_X7R_FT-CAP_SMD. Additional termination finish options may be available. Contact KEMET for details. 3 Additional reeling or packaging options may be available. Contact KEMET for details. 1 2 One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Dimensions - Millimeters (Inches) 100% Tin or SnPb Plate L W B T Nickel Plate S Electrodes Conductive Metalization Metric Size Code L Length W Width B Bandwidth S Separation Minimum Mounting Technique 0402 1005 1.00 (.040) 0.05 (.002) 0.50 (.020) 0.05 (.002) 0.30 (.012) 0.10 (.004) 0.30 (.012) Solder Reflow Only 0603 1608 1.60 (.063) 0.15 (.006) 0.80 (.032) 0.15 (.006) 0.35 (.014) 0.15 (.006) 0.70 (.028) 0805 2012 2.00 (.079) 0.20 (.008) 1.25 (.049) 0.20 (.008) 0.50 (0.02) 0.25 (.010) 0.75 (.030) 1206 3216 3.20 (.126) 0.20 (.008) 1.60 (.063) 0.20 (.008) 0.50 (0.02) 0.25 (.010) 1210 3225 3.20 (.126) 0.20 (.008) 2.50 (.098) 0.20 (.008) 1808 4520 4.70 (.185) 0.50 (.020) 2.00 (.079) 0.20 (.008) See Table 2 0.50 (0.02) 0.25 (.010) for Thickness 0.60 (.024) 0.35 (.014) 1812 4532 4.50 (.177) 0.30 (.012) 3.20 (.126) 0.30 (.012) 0.60 (.024) 0.35 (.014) 1825 4564 4.50 (.177) 0.30 (.012) 6.40 (.252) 0.40 (.016) 0.60 (.024) 0.35 (.014) 2220 5650 5.70 (.224) 0.40 (.016) 5.00 (.197) 0.40 (.016) 0.60 (.024) 0.35 (.014) 2225 5664 5.60 (.220) 0.40 (.016) 6.40 (.248) 0.40 (.016) 0.60 (.024) 0.35 (.014) T Thickness Ceramic Surface Mount EIA Size Code N/A Solder Wave or Solder Reflow Solder Reflow Only Qualification/Certification Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance & Reliability. Environmental Compliance Pb-Free and RoHS Compliant. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) Aging Rate (Maximum % Capacitance Loss/Decade Hour) Dielectric Withstanding Voltage (DWV) Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C -55C to +125C 15% 3.0% 250% of rated voltage (5 1 second and charge/discharge not exceeding 50 mA) See Dissipation Factor (DF) Limits Table See Insulation Resistance Limit Table (Rated voltage applied for 120 5 seconds @ 25C) Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 48 or 1,000 hours. Please refer to a part number specific datasheet for referee time details. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and dissipation factor (DF) measured under the following conditions: 1 kHz 50 Hz and 1.0 0.2 Vrms if capacitance 10 F 120 Hz 10 Hz and 0.5 0.1 Vrms if capacitance > 10 F Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." Insulation Resistance Limit Table (X7R Dielectric) EIA Case Size 1,000 Megohm Microfarads or 100 G 500 Megohm Microfarads or 10 G 0201 N/A ALL 0402 < 0.012 F 0.012 F 0603 < 0.047 F 0.047 F 0805 < 0.047 F 0.047 F 1206 < 0.22 F 0.22 F 1210 < 0.39 F 0.39 F 1808 ALL N/A 1812 < 2.2 F 2.2 F 1825 ALL N/A 2220 < 10 F 10 F 2225 ALL N/A (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Dissipation Factor (DF) Limits Table EIA Case Size Rated DC Voltage Capacitance < 16 0402 16/25 All < 16 5.0% < 1.0 uF > 25 16/25 < 16 16/25 > 25 < 16 16/25 > 25 16/25 1.0 uF 2.2 F < 1.0 F > 2.2 F 16/25 1210 < 10 F 16/25 10 F 16/25 > 25 2.5% 10.0% 3.5% 10.0% 5.0% < 22 F 3.5% 2.5% 22 F < 16 1812 - 2225 3.5% 2.5% > 25 < 16 5.0% 5.0% < 16 16/25 10.0% 1.0 F > 25 < 16 3.5% 2.5% < 16 1206 3.5% 2.5% < 16 0805 5.0% > 25 16/25 0603 Dissipation Factor 10.0% 5.0% All 3.5% 2.5% (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance Dielectric Case Size Rated DC Voltage Capacitance Value < 16 0402 16/25 7.5 16/25 > 25 < 16 16/25 > 25 X7R < 1.0 uF > 25 < 16 1206 1.0 uF 2.2 F < 1.0 F > 2.2 F 16/25 1210 < 10 F 16/25 10 F 16/25 > 25 3.0 20.0 5.0 20.0 7.5 < 22 F 5.0 3.0 22 F < 16 1808 - 2225 5.0 3.0 > 25 < 16 7.5 7.5 < 16 16/25 10% of Initial Limit 20.0 1.0 F > 25 < 16 20% 5.0 3.0 < 16 16/25 Insulation Resistance 5.0 < 16 16/25 0805 All 3.0 < 16 Capacitance Shift 7.5 > 25 16/25 0603 Dissipation Factor (Maximum %) 20.0 7.5 All 5.0 3.0 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 1A - Capacitance Range/Selection Waterfall (0402 - 1206 Case Sizes) 4 3 5 1 2 9 8 4 3 6 5 1 2 A 9 8 4 3 6 5 1 2 A 25 50 6.3 10 16 25 50 100 200 6.3 10 16 25 35 50 100 200 250 6.3 10 16 25 35 50 100 200 250 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB Voltage DC 16 8 10 9 6.3 5 50 3 25 4 10 8 16 9 16 C1206 Voltage DC 6.3 9 8 4 3 5 9 8 4 CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CC CC CC CD DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DC DC DC DC DC DD DG DG DG DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DC DC DC DC DC DD DG DG DG DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DC DC DC DC DC DD DG DG DG DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DC DC DC DC DC DD DG DG DG DG DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DC DD DD DG DG DD DD DE DE DH DH DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DC DD DD DG DG DD DD DE DE DH DH DC DC DC DC DC DC DC DC DC DD DD DD DE DE DE DE DE DG DG DG DG DC DC DC DC DC DC DC DC DC DE DE DE DG DG DC DC DC DC DC DC DC DG DG DG DG DG DG DG EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED ED ED ED EN ED EF EF EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED ED ED ED EN ED EF EF EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED ED ED ED EN ED EF EF EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EG EG EG EF EF EH EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EC EC EC EC EC ED ED ED EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EC EC EC EC EC ED ED ED EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EC EC EB EB EB EB EC EC EC EC EM EG EG EG EB EB EB EB EB EB EB EB EB EB EB EB ED ED ED ED EM EG EG 250 CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB 200 BB BB BB BB BB BB BB BB BB 50 BB BB BB BB BB BB BB BB BB BB BB BB BB 5 1 2 A EB EB EB EB EB EB EB EB EB ED ED ED ED EM C0402 10 16 25 35 5 6.3 6 C0805 250 3 100 4 200 8 35 9 50 2 16 1 C0603 25 5 10 3 6.3 EH EH 100 Cap Voltage Code Code Series BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB 100 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions 200 K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 25 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 50 Cap C0805 Voltage Code Cap Tolerance 10 - 91 pF 100 - 910 100 - 150 pF 101 - 820 180 - 820 pF 181 1000 - 8200 pF 102 - 822 10000 pF 103 12000 pF 123 15000 pF 153 18000 pF 183 22000 pF 223 27000 pF 273 33000 pF 333 39000 pF 393 47000 pF 473 56000 pF 563 68000 pF 683 82000 pF 823 0.1 F 104 0.12 F 124 0.15 F 154 0.18 F 184 0.22 F 224 0.27 F 274 0.33 F 334 0.39 F 394 0.47 F 474 0.56 F 564 0.68 F 684 0.82 F 824 1 F 105 1.2 F 125 1.5 F 155 1.8 F 185 2.2 F 225 2.7 F 275 3.3 F 335 3.9 F 395 4.7 F 475 5.6 F 565 6.8 F 685 8.2 F 825 10 F 106 12 F 126 15 F 156 18 F 186 22 F 226 C0603 10 Cap Code C0402 6.3 Cap Series 1 2 A 9 8 4 3 6 C1206 xx1 Available only in K, M tolerance. xx2 Available only in M tolerance. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. C1002_X7R_SMD * 5/28/2013 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 1B - Capacitance Range/Selection Waterfall (1210 - 2225 Case Sizes) 1 2 A 3 Voltage DC 200 250 50 100 200 25 50 100 200 250 50 100 200 250 25 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC FF FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC FF FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC FF FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FG FM FG FG FH FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FG FG FG FG FH FM FK FS Voltage DC 9 8 4 3 2 A 5 1 2 A FT GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE GB GB GB GB GB GB GB GD GH GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GG GG GG GG GG GJ GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GG GG GG GG GG GJ GO GO GO HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HC HD HF HB HB HB HB HB HB HB HB HE HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HF HF HB HB HB HB HB HE HE HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF C1808 KC KC KC KC KC KC KC KC KD KD KD KE KE KE KC KC KC KC KC KC KC KC KD KD KD KE KE KE 1 2 A 50 5 2 A 5 1 2 A 3 5 1 C1825 KC KC KC KC KC KC KC KC KC KC KC KC KD KE A 1 C1812 KC KC KC KC KC KB KB KB KB KB KB KB KB KB KC KD KD 2 100 5 25 3 250 2 200 50 1 KE KE KE KE KE KE KE JC JC JC JC JC JC JC JC JC JC JD JD JF JF 100 25 5 JF KE KE KE KE KE KE KE KE KE KE JC JC JC JC JC JC JC JC JC JC JD JD JF JF 50 200 A JF KE KE KE KE KE KE KE KE KE KE KE JE JE JE JE JE JE JE JE JB JB JB JB JB JC JC JC JC JC JC JC JC JC JC JC JD JF JF 250 100 2 JE JE JE JE JE JE JE JE JB JB JB JB JB JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JD JF 100 50 1 JE JE JE JE JE JE JE JE JB JB JB JB JB JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JD JF 200 250 GK GK 5 C1210 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GG GG GG GG GG GG GG GG 250 LD LD LD LD LD LD LD LD GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE 200 LF LF LF LF LF LF LF 100 LF LF LF LF LF LF LF LF LF LD LD LD LD LD LD LD LD LD LD LD LD LD LD 50 FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FF FG LF LF LF LF LF LF LF LF LF LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD 250 FB FB FB FB FB FE FE FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FF FG 200 FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FD FD FD FD FD FD FD FD FD FF FG FL FM 200 Cap Voltage Code Code Series 1 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions 50 K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 100 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J C2225 5 250 5 100 A 200 2 50 1 250 5 200 3 50 2 100 1 25 5 16 A 10 2 10 1 100 C2220 5 25 C1825 3 6.3 Cap C1812 4 Cap Tolerance 10 - 91 pF 100 - 910 100 - 270 pF 101 - 271 330 pF 331 390 pF 391 470 - 1,200 pF 471 - 122 1,500 pF 152 1,800 pF 182 2,200 pF 222 2,700 pF 272 3,300 pF 332 3,900 pF 392 4,700 pF 472 5,600 pF 562 6,800 pF 682 8,200 pF 822 10,000 pF 103 12,000 pF 123 15,000 pF 153 18,000 pF 183 22,000 pF 223 27,000 pF 273 33,000 pF 333 39,000 pF 393 47,000 pF 473 56,000 pF 563 68,000 pF 683 82,000 pF 823 0.10 uF 104 0.12 uF 124 0.15 uF 154 0.18 uF 184 0.22 uF 224 0.27 uF 274 0.33 uF 334 0.39 uF 394 0.47 uF 474 0.56 uF 564 0.68 uF 684 0.82 uF 824 1.0 uF 105 1.2 uF 125 1.5 uF 155 1.8 uF 185 2.2 uF 225 2.7 uF 275 3.3 uF 335 3.9 uF 395 4.7 uF 475 5.6 uF 565 C1808 8 50 C1210 9 16 Series Voltage Code 6.3 Cap Cap Code C2220 C2225 xx1 Available only in K, M tolerance. xx2 Available only in M tolerance. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. C1002_X7R_SMD * 5/28/2013 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 1B - Capacitance Range/Selection Waterfall (1210 - 2225 Case Sizes) cont'd 5 1 2 A 250 25 50 100 200 250 50 100 250 A 200 2 250 1 200 5 100 3 50 A 250 2 100 1 200 5 200 50 A 100 25 2 50 200 1 250 5 C2225 100 3 C2220 200 2 100 25 1 FG FG FG FM FH FH FH FK FH FH FH FS 2 3 5 C1210 C1808 50 1 25 5 250 A 200 2 100 1 50 5 250 3 100 4 200 8 50 9 25 JO 200 FS FS FS FS FS 100 JO 50 JO 250 FM FM 100 JO 200 JF 50 GK 25 Cap Voltage Code Code Series 5 16 Voltage DC Cap A 10 M M M M M M M M 2 6.3 K K K K K K K K 1 C1825 1 2 A 5 1 2 A Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions Cap Tolerance J J J J J J J J 5 50 3 250 4 200 8 C1812 50 9 Voltage DC C1808 100 Voltage Code 16 685 825 106 126 156 186 226 476 C1210 10 6.8 uF 8.2 uF 10 uF 12 uF 15 uF 18 uF 22 uF 47 uF Series 6.3 Cap Cap Code 1 2 A 5 1 2 A 3 5 C1812 C1825 C2220 C2225 xx1 Available only in K, M tolerance. xx2 Available only in M tolerance. Table 2 - Chip Thickness/Packaging Quantities Paper Quantity Plastic Quantity Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel BB CB CC CD DC DD DE DG DH EB EC EN ED EE EF EM EG EH FB FC FD FE FF FG 0402 0603 0603 0603 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 0.50 0.05 0.80 0.07 0.80 0.10 0.80 0.15 0.78 0.10 0.90 0.10 1.00 0.10 1.25 0.15 1.25 0.20 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.20 0.15 1.25 0.15 1.60 0.15 1.60 0.20 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.25 0.15 10,000 4,000 4,000 4,000 4,000 4,000 0 0 0 4,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 50,000 10,000 10,000 10,000 10,000 10,000 0 0 0 10,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2,500 2,500 2,500 4,000 4,000 4,000 2,500 2,500 2,500 2,500 2,000 2,000 4,000 4,000 4,000 2,500 2,500 2,500 0 0 0 0 0 0 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 10,000 10,000 10,000 10,000 10,000 10,000 Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel Paper Quantity Plastic Quantity Package quantity based on finished chip thickness specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. C1002_X7R_SMD * 5/28/2013 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 2 - Chip Thickness/Packaging Quantities cont'd Paper Quantity Plastic Quantity Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel FL FH FM FJ FT FK FS NA NC LD LF GB GC GD GE GH GG GK GJ GO HB HC HD HE HF JB JC JD JE JF JO KB KC KD KE 1210 1210 1210 1210 1210 1210 1210 1706 1706 1808 1808 1812 1812 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 1825 2220 2220 2220 2220 2220 2220 2225 2225 2225 2225 1.40 0.15 1.55 0.15 1.70 0.20 1.85 0.20 1.90 0.20 2.10 0.20 2.50 0.30 0.90 0.10 1.00 0.15 0.90 0.10 1.00 0.15 1.00 0.10 1.10 0.10 1.25 0.15 1.30 0.10 1.40 0.15 1.55 0.10 1.60 0.20 1.70 0.15 2.50 0.20 1.10 0.15 1.15 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 1.50 0.15 2.40 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2,000 2,000 2,000 2,000 1,500 2,000 1,000 4,000 4,000 2,500 2,500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 8,000 8,000 8,000 8,000 4,000 8,000 4,000 10,000 10,000 10,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel Paper Quantity Plastic Quantity Package quantity based on finished chip thickness specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 3 - Chip Capacitor Land Pattern Design Recommendations per IPC-7351 EIA Size Code Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) C Y X V1 V2 C Y X V1 V2 C Y X V1 V2 0.72 0.72 2.20 1.20 0.45 0.62 0.62 1.90 1.00 0.40 0.52 0.52 1.60 0.80 0402 1005 0.50 0603 1608 0.90 1.15 1.10 4.00 2.10 0.80 0.95 1.00 3.10 1.50 0.60 0.75 0.90 2.40 1.20 0805 2012 1.00 1.35 1.55 4.40 2.60 0.90 1.15 1.45 3.50 2.00 0.75 0.95 1.35 2.80 1.70 1206 3216 1.60 1.35 1.90 5.60 2.90 1.50 1.15 1.80 4.70 2.30 1.40 0.95 1.70 4.00 2.00 1210 3225 1.60 1.35 2.80 5.65 3.80 1.50 1.15 2.70 4.70 3.20 1.40 0.95 2.60 4.00 2.90 12101 3225 1.50 1.60 2.90 5.60 3.90 1.40 1.40 2.80 4.70 3.30 1.30 1.20 2.70 4.00 3.00 1808 4520 2.30 1.75 2.30 7.40 3.30 2.20 1.55 2.20 6.50 2.70 2.10 1.35 2.10 5.80 2.40 1812 4532 2.15 1.60 3.60 6.90 4.60 2.05 1.40 3.50 6.00 4.00 1.95 1.20 3.40 5.30 3.70 1825 4564 2.15 1.60 6.90 6.90 7.90 2.05 1.40 6.80 6.00 7.30 1.95 1.20 6.70 5.30 7.00 2220 5650 2.75 1.70 5.50 8.20 6.50 2.65 1.50 5.40 7.30 5.90 2.55 1.30 5.30 6.60 5.60 2225 5664 2.70 1.70 6.90 8.10 7.90 2.60 1.50 6.80 7.20 7.30 2.50 1.30 6.70 6.50 7.00 Only for capacitance values 22 F Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC Standard 7351 (IPC-7351). 1 Soldering Process Recommended Soldering Technique: * Solder wave or solder reflow for EIA case sizes 0603, 0805, and 1206 * All other EIA case sizes are limited to solder reflow only Recommended Soldering Profile: * KEMET recommends following the guidelines outlined in IPC/JEDEC J-STD-020 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 4 - Performance & Reliability: Test Methods and Conditions Stress Reference Test or Inspection Method Terminal Strength JIS-C-6429 Appendix 1, Note: Force of 1.8 kg for 60 seconds. Board Flex JIS-C-6429 Appendix 2, Note: Standard termination system - 2.0 mm (minimum) for all except 3 mm for C0G. Flexible termination system - 3.0 mm (minimum). Magnification 50 X. Conditions: Solderability J-STD-002 a) Method B, 4 hours @ 155C, dry heat @ 235C b) Method B @ 215C category 3 c) Method D, category 3 @ 260C Temperature Cycling JESD22 Method JA-104 1,000 Cycles (-55C to +125C). Measurement at 24 hours +/- 2 hours after test conclusion. Load Humidity: 1,000 hours 85C/85% RH and rated voltage. Add 100 K ohm resistor. Measurement at 24 hours +/- 2 hours after test conclusion. Low Volt Humidity: 1,000 hours 85C/85% RH and 1.5 V. Add 100 K ohm resistor. Measurement at 24 hours +/- 2 hours after test conclusion. t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered. Measurement at 24 hours +/- 2 hours after test conclusion. -55C/+125C. Note: Number of cycles required - 300, maximum transfer time - 20 seconds, dwell time - 15 minutes. Air - Air. Biased Humidity MIL-STD-202 Method 103 Moisture Resistance MIL-STD-202 Method 106 Thermal Shock MIL-STD-202 Method 107 High Temperature Life MIL-STD-202 Method 108 /EIA-198 Storage Life MIL-STD-202 Method 108 150C, 0 VDC for 1,000 hours. Vibration MIL-STD-202 Method 204 5 g's for 20 min., 12 cycles each of 3 orientations. Note: Use 8" X 5" PCB 0.031" thick 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10 - 2,000 Hz Mechanical Shock MIL-STD-202 Method 213 Figure 1 of Method 213, Condition F. Resistance to Solvents MIL-STD-202 Method 215 Add aqueous wash chemical, OKEM Clean or equivalent. 1,000 hours at 125C (85C for X5R, Z5U and Y5V) with 2 X rated voltage applied. Storage & Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature- reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40C and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of receipt. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Construction Reference Item A B C Termination System Material Finish 100% Matte Sn Barrier Layer Ni Base Metal Cu D Inner Electrode Ni E Dielectric Material BaTiO3 Note: Image is exaggerated in order to clearly identify all components of construction. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Capacitor Marking (Optional): These surface mount multilayer ceramic capacitors are normally supplied unmarked. If required, they can be marked as an extra cost option. Marking is available on most KEMET devices but must be requested using the correct ordering code identifier(s). If this option is requested, two sides of the ceramic body will be laser marked with a "K" to identify KEMET, followed by two characters (per EIA-198 - see table below) to identify the capacitance value. EIA 0603 case size devices are limited to the "K" character only. Marking appears in legible contrast. Illustrated below is an example of an MLCC with laser marking of "KA8", which designates a KEMET device with rated capacitance of 100 F. Orientation of marking is vendor optional. _ KA8 Laser marking option is not available on: * C0G, Ultra Stable X8R and Y5V dielectric devices * EIA 0402 case size devices * EIA 0603 case size devices with Flexible Termination option. * KPS Commercial and Automotive Grade stacked devices. Alpha Character 9 Capacitance (pF) For Various Alpha/Numeral Identifiers Numeral 0 1 2 3 4 5 6 7 8 100,000,000 Capacitance (pF) A 0.1 10 10 100 1,000 10,000 100,000 1,000,000 10,000,000 B 0.11 1.1 11 110 1,100 11,000 110,000 1,100,000 11,000,000 110,000,000 C 0.12 12 12 120 1,200 12,000 120,000 1,200,000 12,000,000 120,000,000 D 0.13 13 13 130 1,300 13,000 130,000 1,300,000 13,000,000 130,000,000 E 0.15 15 15 150 1,500 15,000 150,000 1,500,000 15,000,000 150,000,000 160,000,000 F 0.16 16 16 160 1,600 16,000 160,000 1,600,000 16,000,000 G 0.18 18 18 180 1,800 18,000 180,000 1,800,000 18,000,000 180,000,000 H 0.2 20 20 200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000 J 0.22 22 22 220 2,200 22,000 220,000 2,200,000 22,000,000 220,000,000 K 0.24 2.4 24 240 2,400 24,000 240,000 2,400,000 24,000,000 240,000,000 L 0.27 2.7 27 270 2,700 27,000 270,000 2,700,000 27,000,000 270,000,000 M 0.3 30 30 300 3,000 30,000 300,000 3,000,000 30,000,000 300,000,000 N 0.33 33 33 330 3,300 33,000 330,000 3,300,000 33,000,000 330,000,000 P 0.36 36 36 360 3,600 36,000 360,000 3,600,000 36,000,000 360,000,000 Q 0.39 39 39 390 3,900 39,000 390,000 3,900,000 39,000,000 390,000,000 R 0.43 43 43 430 4,300 43,000 430,000 4,300,000 43,000,000 430,000,000 S 0.47 4.7 47 470 4,700 47,000 470,000 4,700,000 47,000,000 470,000,000 T 0.51 5.1 51 510 5,100 51,000 510,000 5,100,000 51,000,000 510,000,000 U 0.56 56 56 560 5,600 56,000 560,000 5,600,000 56,000,000 560,000,000 V 0.62 62 62 620 6,200 62,000 620,000 6,200,000 62,000,000 620,000,000 W 0.68 68 68 680 6,800 68,000 680,000 6,800,000 68,000,000 680,000,000 X 0.75 75 75 750 7,500 75,000 750,000 7,500,000 75,000,000 750,000,000 Y 0.82 82 82 820 8,200 82,000 820,000 8,200,000 82,000,000 820,000,000 Z 0.91 9.1 91 910 9,100 91,000 910,000 9,100,000 91,000,000 910,000,000 a 0.25 25 25 250 2,500 25,000 250,000 2,500,000 25,000,000 250,000,000 b 0.35 35 35 350 3,500 35,000 350,000 3,500,000 35,000,000 350,000,000 d 0.4 40 40 400 4,000 40,000 400,000 4,000,000 40,000,000 400,000,000 e 0.45 45 45 450 4,500 45,000 450,000 4,500,000 45,000,000 450,000,000 f 0.5 50 50 500 5,000 50,000 500,000 5,000,000 50,000,000 500,000,000 m 0.6 60 60 600 6,000 60,000 600,000 6,000,000 60,000,000 600,000,000 n 0.7 70 70 700 7,000 70,000 700,000 7,000,000 70,000,000 700,000,000 t 0.8 80 80 800 8,000 80,000 800,000 8,000,000 80,000,000 800,000,000 y 0.9 90 90 900 9,000 90,000 900,000 9,000,000 90,000,000 900,000,000 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Bar Code Label Anti-Static Reel (R) Embossed Plastic* or Punched Paper Carrier. ET KEM Chip and KPS Orientation in Pocket (except 1825 Commercial, and 1825 and 2225 Military) Sprocket Holes Embossment or Punched Cavity 8 mm, 12 mm or 16 mm Carrier Tape 178 mm (7.00") or 330 mm (13.00") Anti-Static Cover Tape (.10 mm (.004") Maximum Thickness) *EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only. Table 5 - Carrier Tape Configuration - Embossed Plastic & Punched Paper (mm) EIA Case Size Tape Size (W)* Pitch (P1)* 01005 - 0402 8 2 0603 - 1210 8 4 1805 - 1808 12 4 1812 12 8 KPS 1210 12 8 KPS 1812 & 2220 16 12 Array 0508 & 0612 8 4 *Refer to Figures 1 & 2 for W and P1 carrier tape reference locations. *Refer to Tables 6 & 7 for tolerance specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 14 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ODo [10 pitches cumulative tolerance on tape 0.2 mm] Po E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity OD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 6 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) R Reference S1 Minimum Note 2 Note 3 25.0 (0.984) 2.0 0.05 0.600 (0.079 0.002) (0.024) 30 (1.181) P2 T Maximum T1 Maximum 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F P1 3.5 0.05 (0.138 0.002) 5.5 0.05 (0.217 0.002) 7.5 0.05 (0.138 0.002) 4.0 0.10 (0.157 0.004) 8.0 0.10 (0.315 0.004) 12.0 0.10 (0.157 0.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 6). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4). (e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 15 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 2 - Punched (Paper) Carrier Tape Dimensions P2 T Po ODo [10 pitches cumulative tolerance on tape 0.2 mm] A0 F P1 T1 T1 Top Cover Tape W E2 B0 Bottom Cover Tape E1 G Cavity Size, See Note 1, Table 7 Center Lines of Cavity Bottom Cover Tape User Direction of Unreeling Table 7 - Punched (Paper) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 E1 P0 P2 T1 Maximum G Minimum 8 mm 1.5 +0.10 -0.0 (0.059 +0.004 -0.0) 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) 0.10 (0.004) Maximum 0.75 (0.030) R Reference Note 2 25 (0.984) T Maximum W Maximum A0 B 0 1.1 (0.098) 8.3 (0.327) 8.3 (0.327) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Half (2 mm) 8 mm Single (4 mm) E2 Minimum 6.25 (0.246) F 3.5 0.05 (0.138 0.002) P1 2.0 0.05 (0.079 0.002) 4.0 0.10 (0.157 0.004) Note 1 1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that: a) the component does not protrude beyond either surface of the carrier tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. c) rotation of the component is limited to 20 maximum (see Figure 3). d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4). e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. 2. The tape with or without components shall pass around R without damage (see Figure 6). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 16 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 3 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 - 200 Bo Maximum Rotation ( 20 10 T) Typical Component Centerline Ao Figure 4 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape s Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 56 10 72 - 200 5 S) Figure 5 - Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com R C1002_X7R_SMD * 5/28/2013 17 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 6 - Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (O 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 8 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 18 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 7 - Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum 100 mm Minimum Leader 400 mm Minimum Components Top Cover Tape Figure 8 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm Bulk Cassette Packaging (Ceramic Chips Only) Meets Dimensional Requirements IEC-286 and EIAJ 7201 6 8 0.1 8 8 0.1 12.0 0.1 Unit mm *Reference 19.0* 36 00.2 31.5 0.2 0 53 3* 10* 1.5 2.0 3.0 0.1 0 0 0.1 0.2 0 5 0* 110 0.7 Capacitor Dimensions for Bulk Cassette Cassette Packaging - Millimeters EIA Size Code Metric Size Code L Length W Width B Bandwidth S Separation Minimum T Thickness Number of Pieces/Cassette 0402 1005 1.0 0.05 0.5 0.05 0.2 to 0.4 0.3 0.5 0.05 50,000 0603 1608 1.6 0.07 0.8 0.07 0.2 to 0.5 0.7 0.8 0.07 15,000 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 19 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) KEMET Corporation World Headquarters Europe Asia Southern Europe Paris, France Tel: 33-1-4646-1006 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Sasso Marconi, Italy Tel: 39-051-939111 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-460122 2835 KEMET Way Simpsonville, SC 29681 Southeast Lake Mary, FL Tel: 407-855-8886 Espoo, Finland Tel: 358-9-5406-5000 Northeast Wilmington, MA Tel: 978-658-1663 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585 Southeast Asia Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Central Novi, MI Tel: 248-994-1030 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 20 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Electrolytic LifeCalculator http://www.kemet.com:8080/elc Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 21 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) - X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Digitally signed by Jeannette Calvo DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications, cn=Jeannette Calvo, email=jeannettecalvo@kemet.com Date: 2013.06.05 16:35:20 -04'00' (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1002_X7R_SMD * 5/28/2013 22