BA50BC0T - ROHM Co., Ltd. - Datasheet.World

Datashee

t

○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays.

1/16 TSZ02201-0R6R0A600120-1-2

TSZ22111･14･001

www.rohm.com

1A Variable/Fixed Output

LDO Regulators

BAxxBC0 Series(Fixed) BAxxBC0W Series(Fixed) BA00BC0WCP-V5(Variable)

●General Description

The BAxxBC0 are low-saturation regulators with an output current of 1.0 A and an output voltage accuracy of ±2%. A broad

output voltage range is offered, from 1.5V to 10V, and built-in overcurrent protection and thermal shutdown (TSD) circuits

prevent damage due to short-circuiting and overloading, respectively.

●Features

 Output voltage accuracy: ±2%

Broad output range available: 1.5 V -10 V

(BAxxBC0 series)

 Low saturation-voltage type with PNP output

 Built-in overcurrent protection circuit

 Built-in thermal shutdown circuit

 Integrated shutdown switch (BAxxBC0WT,

BAxxBC0WT-5, or BAxxBC0WFP Series,

BA00BC0WCP-V5)

●Key Specifications

 Input Power Supply Voltage: 16.0V(Max.)

 Output voltage:(BA00BC0xx) Variable

(BAxxBC0) Fixed

 Output current: 1A(Max.)

 Shutdown current: 0μA(Typ.)

 Operating temperature range: -40℃ to +105℃

●Applications

All electronic devices that use microcontrollers and

logic circuits

●Packages W (Typ.) x D (Typ.) x H (Max.)

TO252-3 6.50mm x 9.50mm x 2.50mm

TO252-5 6.50mm x 9.50mm x 2.50mm

TO220CP-V5 10.00mm x 20.12mm x 4.60mm

TO220FP-3 10.00mm x 30.50mm x 4.60mm

TO220FP-5 10.00mm x 30.50mm x 4.60mm

TO220FP-5(V5) 10.00mm x 31.50mm x 8.15mm

●Lineup Matrix

Part Number

Output Voltage (V)

Package

1.5 1.8 2.5 3.0 3.3 5.0 6.0 7.0 8.0 9.0 10.0 Variable

BAxxBC0WT { { { { { { { { { { { { TO220FP-5

BAxxBC0WT-V5 { { { - { { - - - { - { TO220FP-5 (V5)

BAxxBC0WFP { { { { { { { { { { { { TO252-5

BAxxBC0T { { { { { { { { { { { - TO220FP-3

BAxxBC0FP { { { { { { { { { { { - TO252-3

BA00BC0WCP-V5 - - - - - - - - - - - { TO220CP-V5

TO220CP-

V

5

TO220FP-3 T

O

22

0

FP-

5

T

O

22

0

FP-

5

(

V

5)

T

O

2

5

2-

3

T

O

2

5

2-

5

2/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Lineup

Maximum output

current(Max.) Shutdown

Switch Package Output

voltage(Typ.) Orderable

Part Number

1A

With Switch

TO252-5

Reel of 2000

1.5 V BA15BC0WFP-E2

1.8 V BA18BC0WFP-E2

2.5 V BA25BC0WFP-E2

3.0 V BA30BC0WFP-E2

3.3 V BA33BC0WFP-E2

5.0 V BA50BC0WFP-E2

6.0 V BA60BC0WFP-E2

7.0 V BA70BC0WFP-E2

8.0 V BA80BC0WFP-E2

9.0 V BA90BC0WFP-E2

10.0 V BAJ0BC0WFP-E2

Variable BA00BC0WFP-E2

TO220FP-5

Tube of 500

1.5 V BA15BC0WT

1.8 V BA18BC0WT

2.5 V BA25BC0WT

3.0 V BA30BC0WT

3.3 V BA33BC0WT

5.0 V BA50BC0WT

6.0 V BA60BC0WT

7.0 V BA70BC0WT

8.0 V BA80BC0WT

9.0 V BA90BC0WT

10.0 V BAJ0BC0WT

Variable BA00BC0WT

TO220FP-5 (V5)

Tube of 500

1.5 V BA15BC0WT-V5

1.8 V BA18BC0WT-V5

2.5 V BA25BC0WT-V5

3.3 V BA33BC0WT-V5

5.0 V BA50BC0WT-V5

9.0 V BA90BC0WT-V5

Variable BA00BC0WT-V5

TO220CP-V5 Reel of 500 Variable BA00BC0WCP-V5E2

No Switch

TO252-3

Reel of 2000

1.5 V BA15BC0FP-E2

1.8 V BA18BC0FP-E2

2.5 V BA25BC0FP-E2

3.0 V BA30BC0FP-E2

3.3 V BA33BC0FP-E2

5.0 V BA50BC0FP-E2

6.0 V BA60BC0FP-E2

7.0 V BA70BC0FP-E2

8.0 V BA80BC0FP-E2

9.0 V BA90BC0FP-E2

10.0 V BAJ0BC0FP-E2

TO220FP-3

Tube of 500

1.5 V BA15BC0T

1.8 V BA18BC0T

2.5 V BA25BC0T

3.0 V BA30BC0T

3.3 V BA33BC0T

5.0 V BA50BC0T

6.0 V BA60BC0T

7.0 V BA70BC0T

8.0 V BA80BC0T

9.0 V BA90BC0T

10.0 V BAJ0BC0T

3/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Block Diagrams / Standard Example Application Circuits / Pin Configurations / Pin Descriptions

[BAxxBC0T] / [BAxxBC0FP]

[BAxxBC0WT] / [BAxxBC0WT-V5] / [BAxxBC0WFP]

Fig.1

[BA00BC0WT] / [BA00BC0WCP-V5] / [BA00BC0WFP] / [BA00BC0WT-V5]

Fig.2

Fig.3

Pin No. Pin name Function

1 CTL Output voltage on/off control

2 Vcc Supply voltage input

3 N.C./GND NC pin/GND*1

4 OUT Power supply output

5 N.C. NC pin

FIN GND GND*2

*1 NC pin for TO252-5 and GND pin for TO220FP-5 and TO220FP-5

(V5).

*2 TO252-5 only.

Pin No. Pin name Function

1 Vcc Supply voltage input

2 N.C./GND NC pin/GND *1

3 OUT Voltage output

FIN GND GND*2

*1 NC pin for TO252-3 and GND pin for TO220FP-3 and TO220FP-5

(V5).

*2 TO252-3 only.

TSD OCP

Driver

Vref

1

0.33μF

CTL

GND(TO252-5)

OUT

Fin

4

22μF

2 Vcc N.C.

5

Vcc

R2

R1

3 N.C.

(TO252-5)

GND

(TO220FP-5,

-5(V5)

TSD OCP

Driver

Vref

1

0.33μF

CTL

GND(TO252-5)

OUT

Fin

4

22μF

2 Vcc C

5

Vcc

R2

R1

3 N.C.

(TO252-5)

GND

(TO220FP-5,

-5(V5)

Pin No. Pin name Function

1 CTL Output voltage on/off control

2 Vcc Supply voltage input

3 N.C./GND NC pin/GND*1

4 OUT Power supply output

5 Ｃ ADJ pin

FIN GND GND*2

*1 NC pin for TO252-5 and GND pin for TO220FP-5 and TO220FP-5

(V5).

*2 TO252-5 only.

1 2345 12345

TO220FP-5 TO220FP-5 (V5)

1 2 3 4 5 12345

TO220FP-5 TO220FP-5 (V5)

TO220FP-3

123

TO252-3

TOP VIEW

1 2 3

TO252-5

TOP VIEW

PIN External capacitor setting range

Vcc (1Pin）Approximately 0.33μF.

OUT (3Pin) 22μF to 1000μF

PIN External capacitor setting range

Vcc (2Pin) Approximately 0.33μF.

OUT (4Pin) 22μF to 1000μF

PIN External capacitor setting range

Vcc (2Pin) Approximately 0.33μF.

OUT (4Pin) 22μF to 1000μF

TO220CP-V5 TO252-5

FIN

1 2 3 4 5

FIN

1 2 3 4 5

1 2 3

4 5

TSD

OCP

Driver

Vre

f

1

Vcc

N.C.

OUT

2

3

22

μ

F

GND

Fin

0.33

μ

F

(TO252-3)

GND

(TO252-3)

R1

R2

(TO220FP-3,

TO220FP-5(V5))

4/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Absolute Maximum Ratings (Ta = 25°C)

Parameter Symbol Limits Unit

Power supply voltage VCC 18*1 V

Power

dissipation

TO252-3

Pd

1200*2

mW

TO252-5 1300*3

TO220FP-3 2000*4

TO220FP-5 2000*4

TO220FP-5 (V5) 2000*4

TO220CP-V5 2000*4

Operating temperature range Topr −40 to +105 °C

Ambient storage temperature Tstg −55 to +150 °C

Maximum junction temperature Tjmax 150 °C

*1 Must not exceed Pd.

*2 Derated at 9.6mW/°C at Ta>25°C when mounted on a glass epoxy board (70 mm × 70 mm × 1.6 mm).

*3 Derated at 10.4mW/°C at Ta>25°C when mounted on a glass epoxy board (70 mm × 70 mm × 1.6 mm).

*4 Derated at 16mW/°C at Ta> 25°C

●Recommended Operating Ratings

Parameter Symbol Min. Max. Unit

Input power supply voltage VCC*5 3.0 16.0 V

Input power supply voltage VCC*6 Vo+1.0 16.0 V

Output current IO - 1 A

Variable output voltage setting value VO 1.5 12 V

*5 When output voltage is 1.5 V, 1.8 V, or 2.5 V. *6 When output voltage is 3.0 V or higher.

●Electrical Characteristics

BAxxBC0 Series BAxxBC0W Series (Unless otherwise specified, Ta = 25°C; VCTL = 3 V; VCCDC*7)

Parameter Symbol Min. Typ. Max. Unit Conditions

Output voltage VO VO (T)

×0.98 VO (T) VO (T)

× 1.02 V Io = 200mA

Shutdown circuit current Isd - 0 10 μA VCTL = 0 V while in off mode

Minimum I/O voltage difference*8 ∆Vd - 0.3 0.5 V Io = 200mA，Vcc = 0.95 × Vo

Output current capacity IO 1 - - A

Input stability*9 Reg.I - 15 35 mV Vcc= Vo+1.0V→16V, Io = 200mA

Load stability Reg.L - 35 75 mV Io = 0mA →1 A

Temperature coefficient of

output voltage*10 Tcvo - ±0.02 - %/°C Io = 5mA､Tj = 0°C to 125℃

Vo (T): Set output voltage

*7 Vo = 1.5 V, 1.8 V, 2.5 V : Vcc = 3.3 V, Vo = 3.0 V, 3.3 V : Vcc = 5 V,

Vo = 5.0 V : Vcc : 8 V, Vo = 6.0 V : Vcc = 9 V, Vo = 8.0 V : Vcc = 11 V,

Vo = 9.0 V : Vcc = 12 V, Vo = 10.0 V : Vcc = 13 V

*8 Vo ≥ 3.3 V

*9 Change Vcc from 3.0 V to 6 V if 1.5 V ≤ Vo ≤ 2.5 V.

*10 Not 100% tested

BA00BC0W Series (Unless otherwise specified, Ta=25℃, Vcc=3.3V, VCTL=3V, Io=200mA, Vo=2.5V setting)

Parameter Symbol Min. Typ. Max. Unit Conditions

Shutdown circuit current Isd - 0 10 μA VCTL = 0V while in OFF mode

Bias Current Ib - 0.5 0.9 mA IO = 0mA

Reference voltage(CTL terminal) Vc 1.225 1.250 1.275 V IO = 50mA

Minimum I/O voltage difference ∆Vd - 0.3 0.5 V IO = 500mA, VCC = 2.5V

Output current capacity Io 1 - - A

Ripple Rejection R.R. 44 55 - dB f=120Hz, ein※12=-20dBV, Io=100mA

Input stability Reg.I - 15 30 mV Vcc = Vo + 1.0 V→16V, Io = 200mA

Load stability Reg.L - 35 75 mV IO = 0mA →1A

Temperature coefficient of output

voltage*11 Tcvo - ±0.02 - %/°C IO = 5mA, Tj=0°C to 125°C

Output Short Current Ios - 0.40 - Ａ Vcc=16V

CTL ON Mode Voltage Vth1 2.0 - - V ACTIVE MODE, IO = 0mA

CTL OFF Mode Voltage Vth2 - - 0.8 V OFF MODE, IO = 0mA

CTL Input Current Iin 40 80 130 μA IO = 0mA

*11 Not 100% tested *12 ein=Input Voltage Ripple

5/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Typi cal Performance Curves (Unless otherwise specified, Ta = 25°C, Vcc = 8 V, VCTL = 2 V, IO = 0 mA)

00.5 1.0 1.5

3

Fig.4

Circuit Current

CIRCUIT CURRENT : ICC[mA]

Fig.7

Load Stability

0

1

2

4

5

6

OUTPUT VOLTAGE : VOUT[V]

Fig.5

Input Stability (Io=0mA)

0

1

2

4

5

6

3

OUTPUT VOLTAGE : VOUT[V]

Fig.6

Input Stability (Io = 1 A)

0

1

2

4

5

6

3

OUTPUT VOLTAGE : VOUT[V]

6/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Typical Performance Curves - continued

Fig.10

Output Voltage vs Temperature

Fig.11

Circuit Current Temperature

Fig.9

Ripple Rejection

Fig.8

I/O Voltage Difference

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3

OUT PUT CURRE NT ： IOUT [ A]

DROPOU T VOL TA GE ： ΔVd [V]

[BA50BC0WFP]

7/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Typical Performance Curves - continued

Fig.13

CTL Voltage vs Output Voltage

Fig.12

Circuit Current Classified by Load

Fig.14

CTL Voltage vs CTL Current

[BA50BC0WFP]

0

0.1

0.2

0.3

0.4

0.5

0.6

0 2 4 6 8 10 12 14 16 18

CONTROL VOLTAGE ： V CTL

[V]

CONTROL ＣURRENT ： I CTL

[uA]

[BA50BC0WFP]

Fig.15

Thermal Shutdown Circuit

[V]

[BA50BC0WFP]

8/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

Application Information

●I/O equivalence circuit

●Power Dissipation

• TO220FP-3/TO220FP-5/TO220FP-5V5） • TO252-3/TO252-5

The characteristics of the IC are greatly influenced by the operating temperature. If the temperature exceeds the maximum

junction temperature Tjmax, deterioration or damage may occur. Implement proper thermal designs to ensure that power

dissipation is within the permissible range in order to prevent instantaneous damage resulting from heat and maintain the

reliability of the IC for long-term operation.

The following method is used to calculate the power consumption Pc (W).

Pc = (Vcc – Vo) × Io + Vcc × Icca

Power dissipation Pd ≧ Pc

The load current Io is calculated:

Calculation Example:

Vcc = 6.0 V and Vo = 5.0 V at Ta = 85°C

31kΩ

2kΩ

27kΩ

CTL

Vcc

R2

R1

Vcc

OUT

Fig.16 Fig.17

* For the BA00BC0WT, connect R1 and

R2 externally between the C and GND

pins and between the OUT and C pins.

Fig.18 Fig.19

0

15

25

20

10

5

25 50 75 125 150100

0

A

MBIENT TEMPERATURE：Ta [ °C]

(1)20.0

(2)2.0

(2) During IC without heat sink operation.

θj-a = 62.5 (°C/W)

(1) When using an infinite heat sink.

θj-c = 6.25 (°C/W)

POWER DISSIPATION：Pd [W]

0

1.2

2.0

1.6

0.8

0.4

25 50 75 125 150100

0

A

MBIENT TEMPERATURE：Ta [ °C]

1.30

IC mounted on a ROHM standard board

Board size: 70 × 70 × 1.6 mm

Copper foil area: 7 × 7 mm

TO252-5 θja=96.2 (°C/W)

TO252-3 θja＝104.2 (°C/W)

POWER DIDDIPATION：Pd [W]

TO252-5

TO252-3

θ

ja = 96.2°C/W → −10.4mW/°C

25°C = 1300mW → 85°C = 676mW

Vcc : Input voltage

Vo : Output current

IO : Load current

Icca : Circuit current

Io ≦ Pd − Vcc × Icca

Vcc − Vo

Io≦ 0.676 − 6.0 × Icca

6.0 − 5.0

Io ≦ 550mA (Icca ≈ 20mA)

Equation: VO = Vc × (R1 + R2) / R1

(Vc = 1.25 V (Typ.))

The recommended R1 value is

a

pp

roximatel

y

30 kΩ to 150 kΩ.

9/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

31kΩ

2kΩ

27kΩ

CTL

Refer to the above and implement proper thermal designs so that the IC will not be used under excessive power dissipation

conditions under the entire operating temperature range.

The power consumption Pc of the IC in the event of shorting (i.e. the Vo and GND pins are shorted) can be obtained from

the following equation:

Pc = Vcc × (Icca + Ishort) (Ishort: short current).

●Peripheral Circuit Considerations

• Vcc pin

Insert a capacitor (0.33μF approx.) between VCC and GND.

The capacitance will vary depending on the application. Use a suitable capacitance and implement designs with

sufficient margins.

• GND pin

Verify that there is no potential difference between the ground of the application board and the IC.

If there is a potential difference, the set voltage will not be output accurately, resulting in unstable IC operation.

Therefore, lower the impedance by designing the ground pattern as wide and as short as possible.

• CTL terminal

The CTL terminal turns on at an operating power

supply voltage of 2.0 V or higher and turns off at 0.8 V

or lower.

There is no particular order when turning the power

supply and CTL terminals on or off.

Fig.20 Input Equivalent Circuit

●Vo Terminal

Insert a capacitor between the Vo and GND pins in order to prevent output oscillation.

Fig.21 Output Equivalent Circuit Fig.22 ESR vs. IO (22μF)

The capacitance may vary greatly with temperature changes, thus making it impossible to completely prevent oscillation.

Therefore, use a tantalum aluminum electrolytic capacitor with a low ESR (Equivalent Serial Resistance). The output will

oscillate if the ESR is too high or too low, so refer to the ESR characteristics in Fig.22 and operate the IC within the stable

region. Use a capacitor within a capacitance between 22μF and 1,000μF.

Below figure, it is ESR-to-Io stability Area characteristics, measured by 22μＦ-ceramic-capacitor and resistor connected in series.

This characteristic is not equal value perfectly to 22µＦ-aluminum electrolytic capacitor in order to measurement method.

Note, however, that the stable range suggested in the figure depends on the IC and the resistance load involved, and can

vary with the board’s wiring impedance, input impedance, and/or load impedance. Therefore, be certain to ascertain the

final status of these items for actual use.

Keep capacitor capacitance within a range of 22µF to 1000μF. It is also recommended that a 0.33μF bypass capacitor be

connected as close to the input pin-GND as location possible. However, in situations such as rapid fluctuation of the input

voltage or the load, please check the operation in real application to determine proper capacitance.

OUT

22 μF

IC

200 400 600 800 10000

0.05

0.075

0.1

0.2

0.5

1.0

2.0

Io [mA]

ESR [Ω]

Oscillation re

g

ion

Oscillation region

Stable region

10.0

10/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Operational Notes

1. Absolute maximum ratings

An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break

down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated

values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses.

2. GND voltage

The potential of GND pin must be minimum potential in all operating conditions.

3. Thermal design

Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating

conditions.

4. Inter-pin shorts and mounting errors

Use caution when positioning the IC for mounting on printed circuit boards.

The IC may be damaged if there is any connection error or if pins are shorted together.

5. Actions in strong electromagnetic field

Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to

malfunction.

6. Testing on application boards

When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.

Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or

removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic

measure. Use similar precaution when transporting or storing the IC.

7. Regarding input pin of the IC

This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them

isolated.

P-N junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic

diode or transistor. For example, the relation between each potential is as follows:

When GND > PIN A and GND > PIN B, the P-N junction operates as a parasitic diode.

When GND > PIN B, the P-N junction operates as a parasitic transistor.

Parasitic diodes can occur inevitable in the structure of the IC. The operation of parasitic diodes can result in mutual

interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic diodes

operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should not be used.

8. Ground Wiring Pattern

When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,

placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage

variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change

the GND wiring pattern of any external components, either.

9. Thermal shutdown circuit

The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed

only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue

to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is assumed.

10. Overcurrent Protection Circuit

An overcurrent protection circuit is incorporated in order to prevention destruction due to short-time overload currents.

Continued use of the protection circuits should be avoided. Please note that the current increases negatively impact the temperature.

11. Damage to the internal circuit or element may occur when the polarity of the Vcc pin is opposite to that of the other pins in

applications. (I.e. Vcc is shorted with the GND pin while an external capacitor is charged.) Use a maximum capacitance

of 1000μF for the output pins. Inserting a diode to prevent back-current flow in series with Vcc or bypass diodes

between Vcc and each pin is recommended.

11/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

Fig.23 Bypass Diode Fig.24 Example of Simple Bipolar IC Architecture

Status of this document

The Japanese version of this document is formal specification. A customer may use this translation version only for a reference

to help reading the formal version.

If there are any differences in translation version of this document formal version takes priority.

～

GND

P基板

N

P

N N

P＋

（端子 A）

抵抗

～

GND

Ｎ

Ｐ

N Ｎ

P＋ P＋

（端子 B）

トランジスタ

(

NPN

)

B

N

E

C

GND

P基板

寄生素子

Transistor (NPN)

Resistor

（PIN A）

P substrate Parasitic elements

（PIN B）

N

P

N

(

PINA

)

GND

Parasitic elements

～

GND

(PINB)

B

C

E

Parasitic elements or

transistors

～

P substrate

Parasitic elements

VCC

Output pin

Diode for preventing back current flow

Bypass Diode

12/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Ordering Information

B A x x B C 0 x x x - E2

Part

Number

Output voltage

00:Variable

Other:Fixed

Current

capacity

BC0 : 1A

Shutdown

switch

W : Include

None:Without

Packages

FP : TO252-3

TO252-5

T : TO220FP-3

TO220FP-5

TO220FP-5(V5)

CP : TO220CP-V5

Packaging and forming specification

E2: Embossed tape and reel

None: Container tube

●Physical Dimension Tape and Reel Information

(Unit : mm)

TO252-3

21 3

0.8

0.65 0.65

1.5

2.5

0.75

FIN

6.5±0.2

2.3±0.2 2.3±0.2

0.5±0.1

1.0±0.2

2.3±0.2

9.5±0.5

0.5±0.1

5.5±0.2 1.5±0.2

5.1+0.2

-

0.1 C0.5

Direction of feed

1pin

Reel ∗ Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

The direction is the 1pin of product is at the lower left when you hold

reel on the left hand and you pull out the tape on the right hand

2000pcs

E2

( )

(Unit : mm)

TO252-5

123 54

0.8

0.5 1.27

1.5

2.5

FIN

6.5±0.2 2.3±0.2

0.5±0.1

1.0±0.2

9.5±0.5

0.5±0.1

5.5±0.2 1.5±0.2

C0.5

5.1+0.2

-

0.1

Direction of feed

1pin

Reel ∗ Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

The direction is the 1pin of product is at the lower left when you hold

reel on the left hand and you pull out the tape on the right hand

2000pcs

E2

( )

(Unit : mm)

TO220CP-V5

16.92

0.92

φ3.2±0.1 4.5±0.1

0.82±0.1

8.0±0.2

1.58

0.42±0.1

12.0±0.2

1.7781.444

4.92±0.2

10.0+0.3

-

0.1 2.8+0.2

-

0.1

13.60

15.2

-

0.2

+0.4

4.12

1.0±0.2

(1.0)

(2.85)

Direction of feed

1pin

Reel ∗ Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

The direction is the 1pin of product is at the lower left when you hold

reel on the left hand and you pull out the tape on the right hand

500pcs

E2

()

13/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

(Unit : mm)

TO220FP-5(V5)

0.7

7.0

10.0

1.778

12345

1.2

0.8

1.8±0.2

8.0±0.2

12.0±0.2

17.0

31.5Max.

φ3.2±0.1

−0.2

+0.4

+ 0.3

− 0.1

+ 0.3

− 0.1 2.8

4.5

0.5±0.1

−0.1

+0.2

+0.3

−0.1

(2.85)

4.25

(2.0)

23.4

17.5

25.8

8.15

∗ Order quantity needs to be multiple of the minimum quantity.

TubeContainer

Quantity

Direction of feed 500pcs

Direction of products is fixed in a container tube

(Unit : mm)

TO220FP-3

231

+0.4

φ

3.2±0.1

0.55

17.0

12.0±0.2

8.0±0.2

2.54±0.5

13.5Min.

5.0±0.2

0.8

2.54±0.5

1.3

−0.1

+0.3

10.0

7.0

1.8±0.2

−0.2

−0.1

+0.3

2.6±0.5

−0.05

+0.1

+0.2

−0.1

+0.3

4.5

2.8

∗ Order quantity needs to be multiple of the minimum quantity.

TubeContainer

Quantity

Direction of feed 500pcs

Direction of products is fixed in a container tube

(Unit : mm)

TO220FP-5

7.0

10.0

2.8

4.5

1.778 0.5±0.1

1.2

0.8

1.8±0.28.0±0.2

0.7

12.0±0.2

17.0

13.5Min.

φ3.2±0.1

−0.2

+0.4

+0.3

−0.1

+0.2

+0.3

−0.1

+0.3

−0.1

23451

2.85

∗ Order quantity needs to be multiple of the minimum quantity.

TubeContainer

Quantity

Direction of feed 500pcs

Direction of products is fixed in a container tube

14/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Marking Diagrams

TO220FP-3 (TOP VIEW)

Part Number Marking

LOT Number

TO252-3

(TOP VIEW)

Part Number Marking

LOT Numbe

r

TO252-5

(TOP VIEW)

Part Number Marking

LOT Number

TO220CP-V5 (TOP VIEW)

Part Number Marking

LOT Number

TO220FP-5 (TOP VIEW)

Part Number Marking

LOT Number

TO220FP-5 (V5) (TOP VIEW)

Part Number Marking

LOT Number

15/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

Orderable

Part Number Package Part Number Marking

BA15BC0WFP-E2

TO252-5

15BC0W

BA18BC0WFP-E2 18BC0W

BA25BC0WFP-E2 25BC0W

BA30BC0WFP-E2 30BC0W

BA33BC0WFP-E2 33BC0W

BA50BC0WFP-E2 50BC0W

BA60BC0WFP-E2 60BC0W

BA70BC0WFP-E2 70BC0W

BA80BC0WFP-E2 80BC0W

BA90BC0WFP-E2 90BC0W

BAJ0BC0WFP-E2 J0BC0W

BA00BC0WFP-E2 00BC0W

BA15BC0WT

TO220FP-5

15BC0W

BA18BC0WT 18BC0W

BA25BC0WT 25BC0W

BA30BC0WT 30BC0W

BA33BC0WT 33BC0W

BA50BC0WT 50BC0W

BA60BC0WT 60BC0W

BA70BC0WT 70BC0W

BA80BC0WT 80BC0W

BA90BC0WT 90BC0W

BAJ0BC0WT J0BC0W

BA00BC0WT 00BC0W

BA15BC0WT-V5

TO220FP-5 (V5)

15BC0W

BA18BC0WT-V5 18BC0W

BA25BC0WT-V5 25BC0W

BA33BC0WT-V5 33BC0W

BA50BC0WT-V5 50BC0W

BA90BC0WT-V5 90BC0W

BA00BC0WT-V5 00BC0W

BA00BC0WCP-V5E2 TO220CP-V5 00BC0W

BA15BC0FP-E2

TO252-3

BA15BC0

BA18BC0FP-E2 BA18BC0

BA25BC0FP-E2 BA25BC0

BA30BC0FP-E2 BA30BC0

BA33BC0FP-E2 BA33BC0

BA50BC0FP-E2 BA50BC0

BA60BC0FP-E2 BA60BC0

BA70BC0FP-E2 BA70BC0

BA80BC0FP-E2 BA80BC0

BA90BC0FP-E2 BA90BC0

BAJ0BC0FP-E2 BAJ0BC0

BA15BC0T

TO220FP-3

BA15BC0

BA18BC0T BA18BC0

BA25BC0T BA25BC0

BA30BC0T BA30BC0

BA33BC0T BA33BC0

BA50BC0T BA50BC0

BA60BC0T BA60BC0

BA70BC0T BA70BC0

BA80BC0T BA80BC0

BA90BC0T BA90BC0

BAJ0BC0T BAJ0BC0

16/16

BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5 Datasheet

TSZ02201-0R6R0A600120-1-2

TSZ22111･15･001

www.rohm.com

●Revision History

Date Revision Changes

26.Jun.2012 001 New Release

Datasheet

Notice - Rev.003

Notice

●General Precaution

1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.

ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any

ROHM’s Products against warning, caution or note contained in this document.

2) All information contained in this document is current as of the issuing date and subject to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales

representative.

●Precaution on using ROHM Products

1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,

OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you

intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport

equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car

accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or

serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.

Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any

damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific

Applications.

2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3) Our Products are designed and manufactured for use under standard conditions and not under any special or

extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any

special or extraordinary environments or conditions. If you intend to use our Products under any special or

extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of

product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4) The Products are not subject to radiation-proof design.

5) Please verify and confirm characteristics of the final or mounted products in using the Products.

6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual

ambient temperature.

8) Confirm that operation temperature is within the specified range described in the product specification.

9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Datasheet

Notice - Rev.003

●Precaution for Mounting / Circuit board design

1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the

ROHM representative in advance.

For details, please refer to ROHM Mounting specification

●Precautions Regarding Application Examples and External Circuits

1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2) You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

●Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

●Precaution for Storage / Transportation

1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2) Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3) Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

●Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

●Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

●Precaution for Foreign Exchange and Foreign Trade act

Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,

please consult with ROHM representative in case of export.

●Precaution Regarding Intellectual Property Rights

1) All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable

for infringement of any intellectual property rights or other damages arising from use of such information or data.:

2) No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the information contained in this document.

Datasheet

Notice - Rev.003

●Other Precaution

1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

2) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

4) In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

5) The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.