FEATURES
DLOW OFFSET VOLTAGE: 50µV max
DLOW DRIFT: 0.5µV/5C max
DLOW INPUT BIAS CURRENT: 5nA max
DHIGH CMR: 120dB min
DINPUTS PROTECTED TO +40V
DWIDE SUPPLY RANGE: +2.25V to +18V
DLOW QUIESCENT CURRENT: 700µA
D8-PIN PLASTIC DIP, SO-8
APPLICATIONS
DBRIDGE AMPLIFIER
DTHERMOCOUPLE AMPLIFIER
DRTD SENSOR AMPLIFIER
DMEDICAL INSTRUMENTATION
DDATA ACQUISITION
DESCRIPTION
The INA128 and INA129 are low power, general
purpose instrumentation amplifiers offering excellent
accuracy. The versatile 3-op amp design and small size
make them ideal for a wide range of applications.
Current-feedback input circuitry provides wide
bandwidth even at high gain (200kHz at G = 100).
A single external resistor sets any gain from 1 to 10,000.
The INA128 provides an industry-standard gain
equation; the INA129 gain equation is compatible with
the AD620.
The INA128/INA129 is laser trimmed for very low of fset
voltage (50µV), drift (0.5µV/°C) and high
common-mode rejection (120dB at G 100). It
operates with power supplies as low as ±2.25V, and
quiescent current is only 700µA—ideal for battery-
operated systems. Internal input protection can
withstand up to ±40V without damage.
The INA128/INA129 is available in 8-pin plastic DIP and
SO-8 surface-mount packages, specified for the –40°C
to +85°C temperature range. The INA128 is also
available in a dual configuration, the INA2128.
A1
A2
A3
40k
40k
40k
40k
VIN 2
1
8
3
6
5
VIN
RG
V+
V
Ref
VO
G=1+49.4k
RG
+
4
7
NOTE: (1) INA129: 24.7k
G=1+ 50k
RG
INA128, INA129
Over-Voltage
Protection
Over-Voltage
Protection
25k(1)
25k(1)
INA128:
INA129:
All trademarks are the property of their respective owners.
INA128
INA129
Precision, Low Power
INSTRUMENTATION AMPLIFIERS
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
         
          
 !     !   
www.ti.com
Copyright 1995−2005, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
2
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage ±18V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Input Voltage Range ±40V. . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Short-Circuit (to ground) Continuous. . . . . . . . . . . . . . . . . .
Operating Temperature −40°C to +125°C. . . . . . . . . . . . . . . . . . .
Storage Temperature Range −55 °C to +125°C. . . . . . . . . . . . . . . . .
Junction Temperature +150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead Temperature (soldering, 10s) +300°C. . . . . . . . . . . . . . . . . . . . .
(1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only , an d
functional operation of the device at these or any other conditions
beyond those specified is not implied.
ELECTROSTATIC DISCHARGE SENSITIVITY
This integrated circuit can be damaged by
ESD. Texas Instruments recommends that all
integrated circuits be handled with appropriate
precautions. Failure to observe proper handling and
installation procedures can cause damage.
ESD damage can range from subtle performance
degradation to complete device failure. Precision
integrated circuits may be more susceptible to damage
because very small parametric changes could cause the
device not to meet its published specifications.
ORDERING INFORMATION
For the most current package and ordering information, see the Package Option Addendum located at the end of this data
sheet.
PIN CONFIGURATION
RG
VIN
V+IN
V
RG
V+
VO
Ref
1
2
3
4
8
7
6
5
Top View
8-Pin DIP and SO-8
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
3
ELECTRICAL CHARACTERISTICS
At TA = +25°C, VS = ±15V, RL = 10k, unless otherwise noted.
INA128P, U
INA129P. U INA128PA, UA
INA129PA, UA
PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNIT
INPUT
Offset Voltage, R TI
Initial TA = +25°C±10±100/G ±50±500/G ±25±100/G ±125±1000/G µV
vs Temperature TA = TMIN to TMAX ±0.2±2/G ±0.5±20/G ±0.2±5/G ±1±20/G µV/°C
vs Power Supply VS = ±2.25V to ±18V ±0.2±20/G ±1±100/G ±2±200/G µV/V
Long-Term Stabilit y ±0.1±3/G µV/mo
Impedance, Differential 1010 || 2 || pF
Common-Mode 1011 || 9 || pF
Common-Mode Voltage Range(1) VO = 0V (V+) − 2 (V+) − 1.4 V
(V−) + 2 (V−) + 1.7 V
Safe Input Voltage ±40 V
Common-Mode Rejection VCM = ±13V, RS = 1 k
G = 1 80 86 73 dB
G = 10 100 106 93 dB
G = 100 120 125 110 dB
G = 1000 120 130 110 dB
BIAS CURRENT ±2±5 ±10 nA
vs Temperature ±30 pA/°C
Offset Current ±1±5 ±10 nA
vs Temperature ±30 pA/°C
NOISE VOLTAGE, RTI G = 1000, RS = 0
f = 10Hz 10 nV/Hz
f = 100Hz 8nV/Hz
f = 1kHz 8nV/Hz
fB = 0.1Hz to 10Hz 0.2 µVPP
Noise Current
f = 10Hz 0.9 pA/Hz
f = 1kHz 0.3 pA/Hz
fB = 0.1Hz to 10Hz 30 pAPP
GAIN
Gain Equation, INA128 1 + (50kΩ/RG) V/V
Gain Equation, INA129 1 + (49.4kΩ/RG) V/V
Range of Gain 1 10000 V/V
Gain Error G = 1 ±0.01 ±0.024 ±0.1 %
G = 10 ±0.02 ±0.4 ±0.5 %
G = 100 ±0.05 ±0.5 ±0.7 %
G = 1000 ±0.5 ±1 ±2 %
Gain vs Temperature(2) G = 1 ±1±10 ppm/°C
50k (or 49.4k) Resistance(2)(3) ±25 ±100 ppm/°C
Nonlinearity VO = ±13.6V, G = 1 ±0.0001 ±0.001 ±0.002 % of FSR
G = 10 ±0.0003 ±0.002 ±0.004 % of FSR
G = 100 ±0.0005 ±0.002 ±0.004 % of FS R
G = 1000 ±0.001 (4) % of FS R
NOTE:Specification is same as INA128P, U or INA129P, U.
(1) Input common-mode range varies with output voltage — see typical curves.
(2) Specified by wafer test.
(3) Temperature coefficient of the 50k (or 49.4k) term in the gain equation.
(4) Nonlinearity measurements in G = 1000 are dominated by noise. Typical nonlinearity is ±0.001%.
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
4
ELECTRICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, RL = 10k, unless otherwise noted.
INA128PA, UA
INA129PA, UA
INA128P, U
INA129P. U
PARAMETER UNITMAXTYPMINMAXTYPMINCONDITIONS
OUTPUT
Voltage: Positive RL = 10k(V+) − 1.4 (V+) − 0.9 V
Voltage: Negative RL = 10k(V−) + 1.4 (V−) + 0.8 V
Load Capacitance Stability 1000 pF
Short-Circuit Current +6/−15 mA
FREQUENCY RESPONSE
Bandwidth, −3dB G = 1 1.3 MHz
G = 10 700 kHz
G = 100 200 kHz
G = 1000 20 kHz
Slew Rate VO = ±10V, G = 10 4V/µs
Settling Time, 0.01% G = 1 7 µs
G = 10 7 µs
G = 100 9 µs
G = 1000 80 µs
Overload Recovery 50% Overdrive 4 µs
POWER SUPPLY
Voltage Range ±2.25 ±15 ±18 V
Current, Total VIN = 0V ±700 ±750 µA
TEMPERATURE RANGE
Specification −40 +85 °C
Operating −40 +125 °C
qJA 8-Pin DIP 80 °C/W
SO-8 SOIC 150 °C/W
NOTE:Specification is same as INA128P, U or INA129P, U.
(1) Input common-mode range varies with output voltage — see typical curves.
(2) Specified by wafer test.
(3) Temperature coefficient of the 50k (or 49.4k) term in the gain equation.
(4) Nonlinearity measurements in G = 1000 are dominated by noise. Typical nonlinearity is ±0.001%.
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
5
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = ±15V, unless otherwise noted.
GAIN vs FREQUENCY
60
50
40
30
20
10
0
10
20
Gain (dB)
Frequency (Hz)
1k 10k 100k 1M 10M
G = 100V/V
G=10V/V
G=1V/V
G = 1000V/V
POSITIVE POWER SUPPLY REJECTION
vs FREQUENCY
Frequency (Hz)
Power Supply Rejection (dB)
140
120
100
80
60
40
20
010 100 1k 10k 100k 1M
G = 100V/V
G = 1000V/V
G=1V/V
G=10V/V
INPUT COMMON−MODE RANGE
Output Voltage (V)
Common−Mode Voltage (V)
05 15
15
10
5
0
10
G=1 G=1
G10 G10
VD/2 +
+
VCM
VO
VD/2 Ref
15V
+15V
+
−5−10−15
−5
−10
−15
vs OUTPUT VOLTAGE, VS = ±15V
COMMON−MODE REJECTION vs FREQUENCY
Frequency (Hz)
Common−Mode Rejection (dB)
10 100 10k 1M1k
140
120
100
80
60
40
20
0100k
G=1V/V
G = 10V/V
G = 100V/V
G = 1000V/V
NEGATIVE POWER SUPPLY REJECTION
vs FREQUENCY
Frequency (Hz)
Power Supply Rejection (dB)
140
120
100
80
60
40
20
010 100 1k 10k 100k 1M
G = 100V/V
G = 1000V/V
G=1V/V
G=10V/V
INPUT COMMON−MODE RANGE
Output Voltage (V)
Common−Mode Voltage (V)
5
4
3
2
1
0
012345
G=1 G=1
G10 G10
G10
G=1
vs OUTPUT VOLTAGE, VS = ±5V, ±2.5V
−1
−2
−3
−4
−5 −1−2−3−4−5
VS = ±2.5V
VS = ±5V
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
6
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, unless otherwise noted.
INPUT−REFERRED NOISE vs FREQUENCY
Frequency (Hz)
110 1k100
1k
100
10
110k
G=1V/V
G = 10V/V
100
10
1
0.1
Current Noise
G = 100, 1000V/V
Input Bias Current Noise (pA/Hz)
Input-Referred Voltage Noise (nV/Hz)
QUIESCENT CURRENT and SLEW RATE
vs TEMPERATURE
0.85
0.8
0.75
0.7
0.65
06
6
5
4
3
2
1
0 255075100125
IQ
Slew Rate
−75 −50 −25 Temperature (°C)
Quiescent Current (
µ
A)
Slew Rate (V/µs)
INPUT OFFSET VOLTAGE WARMUP
10
8
6
4
2
0
0100 200 300 400 500
−2
−4
−6
−8
−10
Time (µs)
Offset Voltage Change (µV)
SETTLING TIME vs GAIN
Gain (V/V)
Settling Time (ms)
100
10
11 10 100 1000
0.01%
0.1%
INPUT OVER−VOLTAGE V/I CHARACTERISTICS
5
4
3
2
1
0
Input Current (mA)
Input Voltage (V)
10 20 30 40050
G=1V/V
G=1V/V
G = 1000V/V
G = 1000V/V VIN IIN
+15V
Flat region represents
normal linear operation.
−1
−2
−3
−4
−5 −10−20−30−40−50
−15V
INPUT BIAS CURRENT vs TEMPERATURE
2
1
0
0 25 50 75 100 125
Input Bias Current (nA)
IOS
IB
−25−50−75
−1
−2
Temperature (°C)
Typical IB and IOS
Range ±2nA at 25°C
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
7
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, unless otherwise noted.
(V−)+1.2
(V−)
OUTPUT VOLTAGE SWING
vs OUTPUT CURRENT
(V+)
0123
4
Output Current (mA)
Output Voltage (V)
(V+)−0.4
(V+)−0.8
(V+)−1.2
(V−)+0.8
(V−)+0.4
(V−)+1.2
(V−)
(V+)
(V+)−0.4
(V+)−0.8
(V+)−1.2
(V−)+0.8
(V−)+0.4
OUTPUT VOLTAGE SWING
vs POWER SUPPLY VOLTAGE
0 5 10 15 2
0
Power Supply Voltage (V)
Output Voltage Swing (V)
RL=10k
−40°C
+85°C
+25°C
−40°C
+85°C
−40°C
+25°C
+85°C
SHORT−CIRCUIT OUTPUT CURRENT
vs TEMPERATURE
18
16
14
12
10
8
6
4
2
00 25 50 75 100 125
Short−Circuit Current (mA)
−25−50−75
Temperature (
°
C)
−ISC
+ISC
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
Frequency (Hz)
PeaktoPeak Output Voltage (VPP)
30
25
20
15
10
5
01k 10k 100k 1M
G=1
G = 10, 100
G = 1000
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
Frequency (Hz)
THD+N(%)
100 1k 10k
1
0.1
0.01
0.001 100k
VO=1Vrms G=1
RL=10k
G=10V/V
RL= 100k
G = 100, RL=100k
G=1,R
L=100k
500kHz Measurement
Bandwidth
Dashed Portion
is noise limited.
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
8
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, unless otherwise noted.
SMALL SIGNAL
(G = 1, 10)
G=1
20mV/div
G=10
5µs/div
SMALL SIGNAL
(G = 100, 1000)
G=100
20mV/div
G=1000
20µs/div
LARGE SIGNAL
(G = 1, 10)
G=1
5V/div
G=10
5µs/div
LARGE SIGNAL
(G = 100, 1000)
G=100
5V/div
G = 1000
20µs/div
VOLTAGE NOISE 0.1 to 10Hz
INPUT−REFERRED, G 100
1s/div
0.1µV/div
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
9
APPLICATIONS INFORMATION
Figure 1 shows the basic connections required for
operation of the INA128/INA129. Applications with nois y
or high impedance power supplies may require
decoupling capacitors close to the device pins as shown.
The output is referred to the output reference (Ref)
terminal which is normally grounded. This must be a
low-impedance connection to assure good
common-mode rejection. A resistance of 8in series
with the Ref pin will cause a typical device to degrade
to approximately 80dB CMR (G = 1).
SETTING THE GAIN
Gain is set by connecting a single external resistor, R G,
connected between pins 1 and 8:
INA128:
G+1)50kW
RG
INA129:
G+1)49.4kW
RG
Commonly used gains and resistor values are shown in
Figure 1.
The 50kterm in Equation 1 (49.4kin Equation 2)
comes from the sum of the two internal feedback
resistors of A1 and A2. These on-chip metal film
resistors are laser trimmed to accurate absolute values.
The accuracy and temperature coefficient of these
internal resistors are included in the gain accuracy and
drift specifications of the INA128/INA129.
The stability and temperature drift of the external gain
setting resistor , R G, also affects gain. RG’s contribution
to gain accuracy and drift can be directly inferred from
the gain equation (1). Low resistor values required for
high gain can make wiring resistance important.
Sockets add to the wiring resistance which will
contribute additional gain error (possibly an unstable
gain error) in gains of approximately 100 or greater.
DYNAMIC PERFORMANCE
The typical performance curve Gain vs Frequency
shows that, despite its low quiescent current, the
INA128/INA129 achieves wide bandwidth, even at high
gain. This is due to the current-feedback topology of the
input stage circuitry. Settling time also remains
excellent at high gain.
NOISE PERFORMANCE
The INA128/INA129 provides very low noise in most
applications. Low frequency noise is approximately
0.2µVPP measured from 0.1 to 10Hz (G 100). This
provides dramatically improved noise when compared
to state-of-the-art chopper-stabilized amplifiers.
RG
Also drawn in simplified form: INA128
Ref
VO
VIN
VIN
+
G+1)50kW
RGG+1)49.4kW
RG
INA128: INA129:
DESIRED RGNEAREST RGNEAREST
GAIN (V/V) () 1% RG ()() 1% RG ()
1NCNCNCNC
2 50.00k 49.9k 49.4k 49.9k
5 12.50k 12.4k 12.35k 12.4k
10 5.556k 5.62k 5489 5.49k
20 2.632k 2.61k 2600 2.61k
50 1.02k 1.02k 1008 1k
100 505.1 511 499 499
200 251.3 249 248 249
500 100.2 100 99 100
1000 50.05 49.9 49.5 49.9
2000 25.01 24.9 24.7 24.9
5000 10.00 10 9.88 9.76
10000 5.001 4.99 4.94 4.87
INA128 INA129
NC: No Connection
A1
A2
A36
7
4
3
8
1
2
VIN
VIN
RG
V+
INA128, INA129
+5
OverVoltage
Protection
OverVoltage
Protection
Load +
VO
Ref
NOTE: (1) INA129: 24.7k
0.1µF
0.1µF
V−
25k(1)
25k(1)
40k40k
40k40k
VO=G (V
IN VIN
+
)
Figure 1. Basic Connections
(1)
(2)
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
10
OFFSET TRIMMING
The I NA128/INA129 i s l aser trimmed f or l ow o f fset v oltage
and offset voltage drift. Most applications require no
external offset adjustment. Figure 2 shows an optional
circuit for trimming the output offset voltage. The voltage
applied t o R ef terminal is s ummed with the o utput. The o p
amp buffer provides low i mpedance at the R ef terminal to
preserv e good comm on- m ode rejection.
10k
OPA177 100
100
1/2 REF200
1/2 REF200
V+
RGINA128
Ref
VO
VIN
VIN
+
±10mV
Adjustment Range
V−
100µA
100µA
Figure 2. Optional Trimming of Output Offset
Voltage
INPUT BIAS CURRENT RETURN PATH
The input impedance of the INA128/INA129 is
extremely high—approximately 1010. However , a path
must be provided for the input bias current of both
inputs. This input bias current is approximately ±2nA.
High input impedance means that this input bias current
changes very little with varying input voltage.
Input circuitry must provide a path for this input bias
current for proper operation. Figure 3 shows various
provisions for an input bias current path. Without a bias
current path, the inputs will float to a potential which
exceeds the common-mode range, and the input
amplifiers will saturate.
If the differential source resistance is low, the bias
current return path can be connected to one input (see
the thermocouple example in Figure 3). With higher
source impedance, using two equal resistors provides
a balanced input with possible advantages of lower
input offset voltage due to bias current and better
high-frequency common-mode rejection.
47k
47k
10k
Microphone,
Hydrophone
etc.
Thermocouple
Center−tap provides
bias current return.
INA128
INA128
INA128
Figure 3. Providing an Input Common-Mode
Current Path
INPUT COMMON-MODE RANGE
The linear input voltage range of the input circuitry of the
INA128/INA129 is from approximately 1.4V below the
positive supply voltage to 1.7V above the negative
supply. As a differential input voltage causes the output
voltage increase, however, the linear input range will be
limited by the output voltage swing of amplifiers A1 and
A2. So the linear common-mode input range is related
to the output voltage of the complete amplifier. This
behavior also depends on supply voltage—see
performance curves, Input Common-Mode Range vs
Output Voltage.
Input-overload can produce an output voltage that
appears normal. For example, if an input overload
condition drives both input amplifiers to their positive
output swing limit, the difference voltage measured by
the output amplifier will be near zero. The output of A3
will b e near 0V even though both inputs are overloaded.
LOW VOLTAGE OPERATION
The INA128/INA129 can be operated on power supplies
as low as ±2.25V. Performance remains excellent with
power supplies ranging from ±2.25V to ±18V. Most
parameters vary only slightly throughout this supply
voltage range—s ee typic al perform anc e curves .
"#$
"#%
SBOS051B − OCTOBER 1995 − REVISED FEBRUARY 2005
www.ti.com
11
Operation at very low supply voltage requires careful
attention to assure that the input voltages remain within
their linear range. Voltage swing requirements of
internal nodes limit the input common-mode range with
low power supply voltage. Typical performance curves,
“Input Common-Mode Range vs Output Voltage” show
the range of linear operation for ±15V, ±5V, and ±2.5V
supplies.
300
+5V
RGINA128 VO
Ref
2.5V − V
2.5V + V
Figure 4. Bridge Amplifier
INA128
RGVO
OPA130
Ref R1
1M
=1
2πR1C1
= 1.59Hz
VIN
+
f−3dB
C1
0.1µF
Figure 5. AC-Coupled Instrumentation Amplifier
REF102
R2
R1
Pt100
Cu
Cu
V+
K
6
10.0V
4
2
INA128 VO
Ref
RG
R3
100 = Pt100 at 0°C
SEEBECK
ISA COEFFICIENT
TYPE MATERIAL (µV/5C) R1, R2
E + Chromel 58.5 66.5k
− Constantan
J + Iron 50.2 76.8k
− Constantan
K + Chromel 39.4 97.6k
− Alumel
T + Copper 38.0 102k
− Constantan
Figure 6. Thermocouple Amplifier with RTD
Cold-Junction Compensation
INA128
RG
IB
R1
VIN
+
A1IO
Load
Ref
IO+VIN
R1
@G
A1IB ERROR
OPA177 ± 1.5nA
OPA131 ± 50pA
OPA602 ± 1pA
OPA128 ± 75fA
Figure 7. Differential Voltage to Current Converter
INA128
RG/2
RG=5.6k
VO
LA
RL
RA
10k
Ref
G=10
2.8k
VGVG
2.8k
1/2
OPA2131
390k
390k
1/2
OPA2131 NOTE: Due to the INA128’s current-feedback
topology, VG is approximately 0.7V less than
the common-mode input voltage. This DC offset
in this guard potential is satisfactory for many
guarding applications.
Figure 8. ECG Amplifier with Right-Leg Drive
PACKAGE OPTION ADDENDUM
www.ti.com 4-Jan-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
INA128P ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA128PA ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA128PAG4 ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA128PG4 ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA128U ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128U/2K5 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128U/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UA ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UA/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UAE4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UAG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA128UG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129P ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA129PA ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA129PAG4 ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
PACKAGE OPTION ADDENDUM
www.ti.com 4-Jan-2012
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
INA129PG4 ACTIVE PDIP P 8 50 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type
INA129U ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129U/2K5 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129U/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129UA ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129UA/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129UAE4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA129UG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
SN412014DRE4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
PACKAGE OPTION ADDENDUM
www.ti.com 4-Jan-2012
Addendum-Page 3
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA128, INA129 :
Enhanced Product: INA129-EP
NOTE: Qualified Version Definitions:
Enhanced Product - Supports Defense, Aerospace and Medical Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
INA128U/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
INA128UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
INA129U/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
INA129UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
INA128U/2K5 SOIC D 8 2500 367.0 367.0 35.0
INA128UA/2K5 SOIC D 8 2500 367.0 367.0 35.0
INA129U/2K5 SOIC D 8 2500 367.0 367.0 35.0
INA129UA/2K5 SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated