TC7660S Super Charge Pump DC-to-DC Voltage Converter Features: * * * * * * * Oscillator boost from 10 kHz to 45 kHz Converts +5V Logic Supply to 5V System Wide Input Voltage Range: +1.5V to +12V Efficient Voltage Conversion (99.9%, typical) Excellent Power Efficiency (98%, typical) Low Power Consumption: 80 A (typical) @ VIN = 5V Low Cost and Easy to Use - Only Two External Capacitors Required * Available in 8-Pin Small Outline (SOIC) and 8-Pin PDIP Packages * Improved ESD Protection (10 kV HBM) * No External Diode Required for High-Voltage Operation Applications: * * * * RS-232 Negative Power Supply Simple Conversion of +5V to 5V Supplies Voltage Multiplication VOUT = n V+ Negative Supplies for Data Acquisition Systems and Instrumentation Package Types PDIP/CERDIP/SOIC BOOST 1 CAP+ 2 GND 3 TC7660S CAP- 4 8 V+ 7 OSC 6 LOW VOLTAGE (LV) 5 VOUT General Description: The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+. Operation below 10 kHz (for lower supply current applications) is possible by connecting an external capacitor from OSC to ground (with pin 1 open). The TC7660S is available in 8-Pin PDIP and 8-Pin Small Outline (SOIC) packages in commercial and extended temperature ranges. 2001-2013 Microchip Technology Inc. DS20001467B-page 1 TC7660S Functional Block Diagram V+ CAP+ 8 BOOST OSC LV 2 1 7 RC Oscillator 2 Voltage Level Translator 4 6 5 CAP- VOUT Internal Internal Voltage Voltage Regulator Regulator Logic Network TC7660S 3 GND DS20001467B-page 2 2001-2013 Microchip Technology Inc. TC7660S 1.0 Operating Temperature Range: C Suffix ...................................................... 0C to +70C E Suffix ................................................... -40C to +85C Storage Temperature Range ........................ -65C to +150C Lead Temperature (Soldering, 10s) ...... ....................... 150C ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings* Supply Voltage ................................................................+13V LV, Boost, and OSC Inputs Voltage: (Note 1) ...................................-0.3V to (V+ + 0.3V) for V+ < 5.5V ......................... (V+ - 5.5V) to (V+ + 0.3V) for V+ > 5.5V Current into LV ......................................... 20 A for V+ > 3.5V Output Short Duration (VSUPPLY 5.5V)............... Continuous Package Power Dissipation: (TA 70C) (Note 2 8-Pin PDIP ..........................................................730 mW 8-Pin SOIC..........................................................470 mW * Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended periods may affect device reliability. ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise noted, specifications measured over operating temperature range with V+ = 5V, COSC = 0, refer to test circuit in Figure 4-1. Parameters Supply Current (Boost pin OPEN or GND) Supply Current (Boost pin = V+) Supply Voltage Range, High Supply Voltage Range, Low Output Source Resistance Oscillator Frequency Sym Min Typ Max Units I+ -- 80 160 A -- -- 180 0C TA +70C -- -- 180 -40C TA +85C -- -- 200 -55C TA +125C I+ A Voltage Conversion Efficiency Oscillator Impedance Note 1: 2: RL = 0C TA +70C -- -- 300 -- -- 350 -40C TA +85C -55C TA +125C -- -- 400 V+H V+L 3.0 -- 12 V Min TAMax, RL = 10 k, LV Open 1.5 -- 3.5 V Min TAMax, RL = 10 k, LV to GND ROUT -- 60 100 IOUT=20 mA -- 70 120 IOUT=20 mA, 0C TA +70C -- 70 120 IOUT=20 mA, -40C TA +85C -- 105 150 IOUT=20 mA, -55C TA +125C -- -- 250 V+ = 2V, IOUT = 3 mA, LV to GND 0C TA +70C -- -- 400 V+ = 2V, IOUT = 3 mA, LV to GND -55C TA +125C -- 10 -- fOSC kHz PEFF Pin 7 open, Pin 1 open or GND Boost Pin = V+ 45 Power Efficiency Conditions 96 98 -- % RL = 5 kBoost Pin Open 95 98 -- TMIN TA TMAX; Boost Pin Open -- 88 -- Boost Pin = V+ VOUTEFF 99 99.9 -- % RL = ZOSC -- 1 -- M V+ = 2V -- 100 -- k V+ = 5V + Connecting any input terminal to voltages greater than V or less than GND may cause destructive latch-up. It is recommended that no inputs from sources operating from external supplies be applied prior to "power up" of the TC7660S. Derate linearly above 50C by 5.5mW/C. 2001-2013 Microchip Technology Inc. DS20001467B-page 3 TC7660S 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, C1 = C2 = 10 F, ESRC1 = ESRC2 = 1 , TA = 25C. See Figure 4-1. OSCILLATOR FREQUENCY (kHz) OSCILLATOR FREQUENCY (kHz) 10 8 VIN = 5V 6 4 VIN = 12V 2 0 -40 IN 60 12 -20 0 20 40 60 80 50 40 VIN = 5V 30 VIN = 12V 20 10 0 -40 100 -20 0 FIGURE 2-1: Unloaded Oscillator Frequency vs. Temperature. VIN = 12V IDD (A) 600 400 200 VIN = 5V 0 20 40 60 80 100 VOLTAGE CONVERSION EFFICIENCY (%) 800 -20 40 60 80 100 FIGURE 2-4: Unloaded Oscillator Frequency vs. Temperature with Boost Pin = VIN. 1000 0 -40 20 TEMPERATURE (C) TEMPERATURE (C) 101.0 100.5 Without Load 100.0 99.5 10K Load 99.0 98.5 TA = 25C 98.0 1 2 TEMPERATURE (C) 3 4 5 6 7 8 9 10 11 12 INPUT VOLTAGE VIN (V) FIGURE 2-2: Supply Current vs. Temperature (with Boost Pin = VIN). FIGURE 2-5: Voltage Conversion. OUTPUT SOURCE RESISTANCE () 70 50 30 IOUT = 20mA TA = 25C 10 1.5 2.5 3.5 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12 SUPPLY VOLTAGE (V) FIGURE 2-3: Output Source Resistance vs. Supply Voltage. DS20001467B-page 4 OUTPUT SOURCE RESISTANCE () 100 100 VIN = 2.5V 80 60 VIN = 5.5V 40 20 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) FIGURE 2-6: vs. Temperature. Output Source Resistance 2001-2013 Microchip Technology Inc. TC7660S Note: Unless otherwise indicated, C1 = C2 = 10 F, ESRC1 = ESRC2 = 1 , TA = 25C. See Figure 4-1. 100 0 POWER EFFICIENCY (%) -4 -6 -8 -10 -12 Boost Pin = V+ 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) FIGURE 2-7: Current. LOAD CURRENT (mA) Output Voltage vs. Output FIGURE 2-10: Power Conversion Efficiency vs. Load. 200 200 175 175 SUPPLY CURRENT IDD (A) SUPPLY CURRENT IDD (A) Boost Pin = Open 80 150 125 VIN = 12.5V 100 75 50 VIN = 5.5V 25 0 -40 -20 0 20 40 1.0 1.5 2.0 3.0 4.5 6.0 7.5 9.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 50.0 55.0 60.0 OUTPUT VOLTAGE VOUT (V) 90 -2 60 80 100 150 125 VIN = 12.5V 100 75 50 VIN = 5.5V 25 0 -40 -20 FIGURE 2-8: Temperature. 0 20 40 60 80 100 TEMPERATURE (C) TEMPERATURE (C) Supply Current vs. FIGURE 2-11: Temperature. Supply Current vs. 200 SUPPLY CURRENT IDD (A) 175 150 125 VIN = 12.5V 100 75 50 VIN = 5.5V 25 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) FIGURE 2-9: Temperature. Supply Current vs. 2001-2013 Microchip Technology Inc. DS20001467B-page 5 TC7660S 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. TABLE 3-1: 3.1 PIN FUNCTION TABLE Pin No. Symbol 1 BOOST 2 CAP+ Charge pump capacitor positive terminal 3 GND Ground terminal 4 CAP- Charge pump capacitor negative terminal 5 VOUT Output voltage 6 LV 7 OSC 8 V+ Description Switching Frequency boost pin Low voltage pin. Connect to GND for V+ < 3.5V Oscillator control input. Bypass with an external capacitor to slow the oscillator. Power supply positive voltage input Switching Frequency Boost Pin (Boost) By connecting the boost pin (pin 1), the switching frequency of the charge pump is increased from 10 Khz typical to 45 Khz typical. By connecting the boost pin (pin1), to the V+ pin (pin 8), the switching frequency of the charge pump is increased from 10 Khz typical to 45 Khz typical. 3.2 Charge Pump Capacitor (CAP+) Positive connection for the charge pump capacitor, or flying capacitor, used to transfer charge from the input source to the output. In the voltage-inverting configuration, the charge pump capacitor is charged to the input voltage during the first half of the switching cycle. During the second half of the switching cycle, the charge pump capacitor is inverted and charge is transferred to the output capacitor and load. It is recommended that a low ESR (equivalent series resistance) capacitor be used. Additionally, larger values will lower the output resistance. 3.3 Ground (GND) It is recommended that a low ESR (equivalent series resistance) capacitor be used. Additionally, larger values will lower the output ripple. 3.6 Low Voltage Pin (LV) The low voltage pin ensures proper operation of the internal oscillator for input voltages below 3.5V. The low voltage pin should be connected to ground (GND) for input voltages below 3.5V. Otherwise, the low voltage pin should be allowed to float. 3.7 Oscillator Control Input (OSC) The oscillator control input can be utilized to slow down or speed up the operation of the TC7660S. Refer to Section 5.4 "Changing the TC7660S Oscillator Frequency", for details on altering the oscillator frequency. 3.8 Power Supply (V+) Positive power supply input voltage connection. It is recommended that a low ESR (equivalent series resistance) capacitor be used to bypass the power supply input to ground (GND). Input and output zero volt reference. 3.4 Charge Pump Capacitor (CAP-) Negative connection for the charge pump capacitor, or flying capacitor, used to transfer charge from the input to the output. Proper orientation is imperative when using a polarized capacitor. 3.5 Output Voltage (VOUT) Negative connection for the charge pump output capacitor. In the voltage-inverting configuration, the charge pump output capacitor supplies the output load during the first half of the switching cycle. During the second half of the switching cycle, charge is restored to the charge pump output capacitor. DS20001467B-page 6 2001-2013 Microchip Technology Inc. TC7660S 4.0 DETAILED DESCRIPTION 4.1 V+ Theory of Operation The four switches in Figure 4-2 are MOS power switches; S1 is a P-channel device, and S2, S3 and S4 are N-channel devices. The main difficulty with this approach is that in integrating the switches, the substrates of S3 and S4 must always remain reversebiased with respect to their sources, but not so much as to degrade their ON resistances. In addition, at circuit start-up, and under output short circuit conditions (VOUT = V+), the output voltage must be sensed and the substrate bias adjusted accordingly. Failure to accomplish this will result in high power losses and probable device latch-up. This problem is eliminated in the TC7660S by a logic network which senses the output voltage (VOUT) together with the level translators, and switches the substrates of S3 and S4 to the correct level to maintain necessary reverse bias. V+ C1 10 F + 3 4 IS 8 2 7 TC7660S 6 5 IL COSC V+ (+5V) RL VOUT C2 + 10 F Note: For large values of COSC (>1000 pF), the values of C1 and C2 should be increased to 100F. FIGURE 4-1: TC7660S Test Circuit. The voltage regulator portion of the TC7660S is an integral part of the anti-latch-up circuitry. Its inherent voltage drop can, however, degrade operation at low voltages. 2001-2013 Microchip Technology Inc. S2 + The TC7660S contains all the necessary circuitry to implement a voltage inverter, with the exception of two external capacitors, which may be inexpensive 10 F polarized electrolytic capacitors. Operation is best understood by considering Figure 4-2, which shows an idealized voltage inverter. Capacitor C1 is charged to a voltage V+ for the half cycle when switches S1 and S3 are closed. (Note: Switches S2 and S4 are open during this half cycle.) During the second half cycle of operation, switches S2 and S4 are closed, with S1 and S3 open, thereby shifting capacitor C1 negatively by V+ volts. Charge is then transferred from C1 negatively by V+ volts. Charge is then transferred from C1 to C2, such that the voltage on C2 is exactly V+ assuming ideal switches and no load on C2. 1 S1 GND S 3 FIGURE 4-2: C1 S4 C2 + VOUT = -VIN Ideal Charge Pump Inverter. To improve low-voltage operation, the "LV" pin should be connected to GND, disabling the regulator. For supply voltages greater than 3.5V, the LV terminal must be left open to ensure latch-up-proof operation and prevent device damage. 4.2 Theoretical Power Efficiency Considerations In theory, a capacitive charge pump can approach 100% efficiency if certain conditions are met: (1) The drive circuitry consumes minimal power. (2) The output switches have extremely low ON resistance and virtually no offset. (3) The impedances of the pump and reservoir capacitors are negligible at the pump frequency. The TC7660S approaches these conditions for negative voltage multiplication if large values of C1 and C2 are used. Energy is lost only in the transfer of charge between capacitors if a change in voltage occurs. The energy lost is defined by: E = 1/2 C1 (V12 - V22) V1 and V2 are the voltages on C1 during the pump and transfer cycles. If the impedances of C1 and C2 are relatively high at the pump frequency (refer to Figure 4-2) compared to the value of RL, there will be a substantial difference in voltages V1 and V2. Therefore, it is desirable not only to make C2 as large as possible to eliminate output voltage ripple, but also to employ a correspondingly large value for C1 in order to achieve maximum efficiency of operation. 4.3 Dos and Don'ts * Do not exceed maximum supply voltages. * Do not connect the LV terminal to GND for supply voltages greater than 3.5V. * Do not short circuit the output to V+ supply for voltages above 5.5V for extended periods; however, transient conditions including start-up are okay. * When using polarized capacitors in the inverting mode, the + terminal of C1 must be connected to pin 2 of the TC7660S and the + terminal of C2 must be connected to GND. DS20001467B-page 7 TC7660S 5.0 APPLICATIONS INFORMATION 5.1 Simple Negative Voltage Converter The dynamic output impedance of the TC7660S is due, primarily, to capacitive reactance of the charge transfer capacitor (C1). Since this capacitor is connected to the output for only half of the cycle, the equation is: Figure 5-1 shows typical connections to provide a negative supply where a positive supply is available. A similar scheme may be employed for supply voltages anywhere in the operating range of +1.5V to +12V, keeping in mind that pin 6 (LV) is tied to the supply negative (GND) only for supply voltages below 3.5V. EQUATION 2 X C = ----------- = 3.18 2fC 1 where: f = 10 kHz and C1 = 10 F. 5.2 V+ C1 10 F 2 + 3 Any number of TC7660S voltage converters may be paralleled to reduce output resistance (Figure 5-2). The reservoir capacitor, C2, serves all devices, while each device requires its own pump capacitor, C1. The resultant output resistance would be approximately: 8 1 7 TC7660S VOUT* C2 + 10 F 6 5 4 EQUATION * VOUT = -V+ for 1.5V V+ 12V FIGURE 5-1: Paralleling Devices ROUT of TC7660S ROUT = ---------------------------------------------------n number of devices Simple Negative Converter. The output characteristics of the circuit in Figure 5-1 are those of a nearly ideal voltage source in series with a 70resistor. Thus, for a load current of -10 mA and a supply voltage of +5V, the output voltage would be -4.3V. V+ 1 C1 8 2 + 3 4 "1" 8 1 7 TC7660S 6 C1 5 + 2 3 4 RL 7 TC7660S "n" 6 5 + FIGURE 5-2: C2 Paralleling Devices Lowers Output Impedance. V+ 8 1 10 F + 2 3 4 7 TC7660S "1" 1 6 5 10 F + 2 3 4 * VOUT = -n V+ for 1.5V V+ 12V FIGURE 5-3: DS20001467B-page 8 + 8 7 TC7660S "n" 10 F 6 VOUT * 5 + 10 F Increased Output Voltage By Cascading Devices. 2001-2013 Microchip Technology Inc. TC7660S 5.3 Cascading Devices The TC7660S may be cascaded as shown (Figure 5-3) to produce larger negative multiplication of the initial supply voltage. However, due to the finite efficiency of each device, the practical limit is 10 devices for light loads. The output voltage is defined by: C1 + 2 3 7 TC7660S COSC 6 VOUT 5 4 EQUATION V+ 8 1 + V OUT = - n V + where n is an integer representing the number of devices cascaded. The resulting output resistance would be approximately the weighted sum of the individual TC7660S ROUT values. 5.4 Changing the TC7660S Oscillator Frequency It may be desirable in some applications (due to noise or other considerations) to increase the oscillator frequency. Pin 1, frequency boost pin may be connected to V+ to increase oscillator frequency to 45 kHz from a nominal of 10 kHz for an input supply voltage of 5.0V. The oscillator may also be synchronized to an external clock as shown in Figure 5-4. In order to prevent possible device latch-up, a 1 k resistor must be used in series with the clock output. In a situation where the designer has generated the external clock frequency using TTL logic, the addition of a 10 k pull-up resistor to V+ supply is required. Note that the pump frequency with external clocking, as with internal clocking, will be half of the clock frequency. Output transitions occur on the positive-going edge of the clock. V+ 1 10 F + 2 3 4 8 TC7660S "1" 7 5.5 Lowering Oscillator Positive Voltage Multiplication The TC7660S may be employed to achieve positive voltage multiplication using the circuit shown in Figure 5-6. In this application, the pump inverter switches of the TC7660S are used to charge C1 to a voltage level of V+-VF (where V+ is the supply voltage and VF is the forward voltage drop of diode D1). On the transfer cycle, the voltage on C1 plus the supply voltage (V+) is applied through diode D2 to capacitor C2. The voltage thus created on C2 becomes (2V+) - (2VF), or twice the supply voltage minus the combined forward voltage drops of diodes D1 and D2. The source impedance of the output (VOUT) will depend on the output current, but for V+ = 5V and an output current of 10 mA, it will be approximately 60. V+ V+ 1 k CMOS GATE 6 8 1 2 3 VOUT 5 + FIGURE 5-4: FIGURE 5-5: Frequency. C2 7 TC7660S 4 10 F External Clocking. FIGURE 5-6: 6 5 D1 + D2 C1 VOUT = (2 V+) - (2 VF) + C2 Positive Voltage Multiplier. It is also possible to increase the conversion efficiency of the TC7660S at low load levels by lowering the oscillator frequency. This reduces the switching losses, and is achieved by connecting an additional capacitor, COSC, as shown in Figure 5-5. Lowering the oscillator frequency will cause an undesirable increase in the impedance of the pump (C1) and the reservoir (C2) capacitors. To overcome this, increase the values of C1 and C2 by the same factor that the frequency has been reduced. For example, the addition of a 100 pF capacitor between pin 7 (OSC) and pin 8 (V+) will lower the oscillator frequency to 1 kHz from its nominal frequency of 10 kHz (a multiple of 10), and necessitate a corresponding increase in the values of C1 and C2 (from 10 F to 100 F). 2001-2013 Microchip Technology Inc. DS20001467B-page 9 TC7660S 5.6 Combined Negative Voltage Conversion and Positive Supply Multiplication Figure 5-7 combines the functions shown in Figure 5-3 and Figure 5-6 to provide negative voltage conversion and positive voltage multiplication simultaneously. For example, this approach would be suitable for generating +9V and - 5V from an existing +5V supply. In this instance, capacitors C1 and C3 perform the pump and reservoir functions, respectively, for the generation of the negative voltage, while capacitors C2 and C4 are pump and reservoir, respectively, for the multiplied positive voltage. There is a penalty in this configuration which combines both functions, however, in that the source impedances of the generated supplies will be somewhat higher due to the finite impedance of the common charge pump driver at pin 2 of the device. V+ 2 3 + C1 VOUT = -V+ 8 1 7 TC7660S 6 5 4 + C2 D1 + C3 VOUT = D2 (2 V+) - (2 VF) + VOUT = -V - C1 + 1 8 2 7 3 10 F TC7660S 4 + 1 M 10 F 6 5 V - input FIGURE 5-8: Conversion. 5.8 Positive Voltage Voltage Splitting The same bidirectional characteristics used in Figure 5-8 can also be used to split a higher supply in half, as shown in Figure 5-9. The combined load will be evenly shared between the two sides. Once again, a high value resistor to the LV pin ensures start-up. Because the switches share the load in parallel, the output impedance is much lower than in the standard circuits, and higher currents can be drawn from the device. By using this circuit, and then the circuit of Figure 5-3, +15V can be converted (via +7.5V and - 7.5V) to a nominal -15V, though with rather high series resistance (~250). C4 V + + 50F R L1 FIGURE 5-7: Combined Negative Converter and Positive Multiplier. 5.7 Efficient Positive Voltage Multiplication/Conversion Since the switches that allow the charge pumping operation are bidirectional, the charge transfer can be performed backwards as easily as forwards. Figure 5-8 shows a TC7660S transforming -5V to +5V (or +5V to +10V, etc.). The only problem is that the internal clock and switch-drive section will not operate until some positive voltage has been generated. An initial inefficient pump, as shown in Figure 5-7, could be used to start this circuit up, after which it will bypass the other (D1 and D2 in Figure 5-7 would never turn on), or else the diode and resistor shown dotted in Figure 5-8 can be used to "force" the internal regulator on. V = OUT + - V -V 2 1 8 2 50F 7 100 k + 1 M 3 - 4 R TC7660S 6 5 L2 + 50F - V FIGURE 5-9: 5.9 - Splitting a Supply in Half. Negative Voltage Generation for Display ADCs The TC7106 is designed to work from a 9V battery. With a fixed power supply system, the TC7106 will perform conversions with input signal referenced to power supply ground. 5.10 Negative Supply Generation for 41/2 Digit Data Acquisition System The TC7135 is a 41/2 digit ADC operating from 5V supplies. The TC7660S provides an inexpensive -5V source. (See AN16 and AN17 for TC7135 interface details and software routines.) DS20001467B-page 10 2001-2013 Microchip Technology Inc. TC7660S 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 8-Lead PDIP (300 mil) Example XXXXXXXX XXXXXNNN YYWW 8-Lead SOIC (3.90 mm) TC7660S CPA e3 256 1320 TC7660S CPA e3 256 Example Example TC7660SE TC7660SE OA e3 1320 NNN Legend: XX...X Y YY WW NNN e3 * Note: Example 1320 OA e31320 256 256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. 2001-2013 Microchip Technology Inc. DS20001467B-page 11 TC7660S 4& '!&" & 5 && 366***' '6 # * !( 5 ! ! & 5 % & & # & N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 7&! ' !:'&! 8"') %! 8,9. 8 8 8; < = & 2, & & > > 1 - 1 1 > > "# &"# ?#& . - -1 # # 5 . 1 = -= -1 : 1 - 1 = 1 # # 5 2 ! & ; & ?#& : & & : 5 !! & #5 !! 7 : #?#& ) :* : #?#& ) = 2 > > ; * + - !" # $% &" ' ()"&'"!&) & #*&& & # + % &, & !& - ' !! #.#&"# '#% ! &"!!#% ! &"!!! & $ #/ ' ! #& .01 2,32 !' ! & $ & " !**&"&& ! !# * , =2 DS20001467B-page 12 2001-2013 Microchip Technology Inc. TC7660S Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2001-2013 Microchip Technology Inc. DS20001467B-page 13 TC7660S Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20001467B-page 14 2001-2013 Microchip Technology Inc. TC7660S ! " "##$%&'!"( 4& '!&" & 5 && 366***' '6 2001-2013 Microchip Technology Inc. # * !( 5 ! ! & 5 % & & # & DS20001467B-page 15 TC7660S NOTES: DS20001467B-page 16 2001-2013 Microchip Technology Inc. TC7660S APPENDIX A: REVISION HISTORY Revision B (August 2013) The following is the list of modifications. 1. 2. Added Appendix A and the "Product Identification System" page. Updated Section 6.0 "Packaging Information". Revision A (May 2001) * Original release of this document. 2001-2013 Microchip Technology Inc. DS20001467B-page 17 TC7660S NOTES: DS20001467B-page 18 2001-2013 Microchip Technology Inc. TC7660S PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X /XX Temperature Range Package Device: TC7660S: DC-to-DC Voltage Converter Temperature Range: C E Package: PA OA OA713 OA723 Examples: a) b) c) d) = = 0C to +70C -40C to +85C e) f) = = = = Plastic DIP, (300 mil body), 8-lead SOIC (Narrow), 8-lead SOIC (Narrow), 8-lead (Tape and Reel) SOIC (Narrow), 8-lead (Reverse Tape and Reel) 2001-2013 Microchip Technology Inc. g) TC7660SEOA:Commercial Temperature, SOIC package TC7660SEOA713:Tape and Reel, Commercial Temperature, SOIC package TC7660SCPA:Commercial Temperature, PDIP package TC7660SEOA:Extended Temperature, SOIC package TC7660SEOA713:Tape and Reel, Extended Temperature, SOIC package TC7660SEPA:Extended Temperature, PDIP package TC7660SEOA723: Reverse Tape and Reel, Extended Temperature DS20001467B-page 19 TC7660S NOTES: DS20001467B-page 20 2001-2013 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2001-2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-62077-300-0 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2001-2013 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS20001467B-page 21 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS20001467B-page 22 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 11/29/12 2001-2013 Microchip Technology Inc.