SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 * FEATURES * * * * * Member of the Texas Instruments WidebusTM Family DOCTM Circuitry Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation Dynamic Drive Capability Is Equivalent to Standard Outputs With IOH and IOL of 24 mA at 2.5-V VCC Control Inputs VIH/VIL Levels Are Referenced to VCCB Voltage If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State * * * * Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications Ioff Supports Partial-Power-Down Mode Operation Fully Configurable Dual-Rail Design Allows Each Port to Operate Over Full 1.4-V to 3.6-V Power-Supply Range Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) DESCRIPTION This 16-bit (dual-octal) noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage bidirectional translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes. The SN74AVCB164245 is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are effectively isolated. The SN74AVCB164245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCB. To ensure the high-impedance state during power up or power down, OE should be tied to VCCB through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND, both ports are in the high-impedance state. ORDERING INFORMATION PACKAGE (1) TA -40C to 85C (1) ORDERABLE PART NUMBER FBGA - GRD Tape and reel 74AVCB164245GRDR FBGA - ZRD (Pb-Free) Tape and reel 74AVCB164245ZRDR TSSOP - DGG Tape and reel SN74AVCB164245GR TVSOP - DGV Tape and reel SN74AVCB164245VR VFBGA - GQL Tape and reel SN74AVCB164245KR VFBGA - ZQL (Pb-Free) Tape and reel 74AVCB164245ZQLR TOP-SIDE MARKING WB4245 AVCB164245 WB4245 WB4245 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus, DOC are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2005, Texas Instruments Incorporated SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS SCES394D - JUNE 2002 - REVISED JUNE 2005 TERMINAL ASSIGNMENTS DGG OR DGV PACKAGE (TOP VIEW) 1DIR 1B1 1B2 GND 1B3 1B4 VCCB 1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCCB 2B5 2B6 GND 2B7 2B8 2DIR 2 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 1A1 1A2 GND 1A3 1A4 VCCA 1A5 1A6 GND 1A7 1A8 2A1 2A2 GND 2A3 2A4 VCCA 2A5 2A6 GND 2A7 2A8 2OE www.ti.com SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 TERMINAL ASSIGNMENTS (56-Ball GQL/ZQL Package) (1) GQL OR ZQL PACKAGE (TOP VIEW) 1 2 3 4 5 6 A B C D E F G H J K (1) 1 2 3 4 5 6 A 1DIR NC NC NC NC 1OE B 1B2 1B1 GND GND 1A1 1A2 C 1B4 1B3 VCCB VCCA 1A3 1A4 D 1B6 1B5 GND GND 1A5 1A6 E 1B8 1B7 1A7 1A8 F 2B1 2B2 2A2 2A1 G 2B3 2B4 GND GND 2A4 2A3 H 2B5 2B6 VCCB VCCA 2A6 2A5 J 2B7 2B8 GND GND 2A8 2A7 K 2DIR NC NC NC NC 2OE NC - No internal connection GRD OR ZRD PACKAGE (TOP VIEW) 1 2 3 4 5 6 TERMINAL ASSIGNMENTS (54-Ball GRD/ZRD Package) (1) A B 1 2 3 4 5 6 A 1B1 NC 1DIR 1OE NC 1A1 B 1B3 1B2 NC NC 1A2 1A3 C 1B5 1B4 VCCB VCCA 1A4 1A5 C D 1B7 1B6 GND GND 1A6 1A7 D E 2B1 1B8 GND GND 1A8 2A1 E F G H (1) F 2B3 2B2 GND GND 2A2 2A3 G 2B5 2B4 VCCB VCCA 2A4 2A5 H 2B7 2B6 NC NC 2A6 2A7 J 2B8 NC 2DIR 2OE NC 2A8 NC - No internal connection xxxxx J xxxxx xxxxx xxxxx xxxxx FUNCTION TABLE (EACH 8-BIT SECTION) INPUTS OPERATION OE DIR L L B data to A bus L H A data to B bus H X Isolation 3 SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 LOGIC DIAGRAM (POSITIVE LOGIC) 1DIR 1 2DIR 48 1A1 25 1OE 47 2A1 2 24 2OE 36 13 1B1 2B1 To Seven Other Channels To Seven Other Channels Pin numbers shown are for the DGG and DGV packages. Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) VCCA VCCB VI MIN MAX -0.5 4.6 I/O ports (A port) -0.5 4.6 I/O ports (B port) -0.5 4.6 Control inputs -0.5 4.6 A port -0.5 4.6 B port -0.5 4.6 A port -0.5 VCCA + 0.5 B port -0.5 VCCB + 0.5 Supply voltage range Input voltage range (2) UNIT V V VO Voltage range applied to any output in the high-impedance or power-off state (2) VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA 100 mA Continuous current through VCCA, VCCB, or GND JA Package thermal impedance (4) Tstg Storage temperature range DGG package 70 DGV package 58 GQL/ZQL package 28 GRD/ZRD package (1) (2) (3) (4) 4 V V C/W 36 -65 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed. The package thermal impedance is calculated in accordance with JESD 51-7. www.ti.com SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS SCES394D - JUNE 2002 - REVISED JUNE 2005 Recommended Operating Conditions (1) (2) (3) over operating free-air temperature range (unless otherwise noted) MIN MAX VCCA Supply voltage VCCI 1.4 3.6 V VCCB Supply voltage 1.4 3.6 V VIH High-level input voltage VIL Low-level input voltage VIH High-level input voltage VIL Low-level input voltage VI Input voltage VO Output voltage IOH Data inputs Data inputs Control inputs (referenced to VCCB) Control inputs (referenced to VCCB) VCCI x 0.65 1.95 V to 2.7 V 1.7 2.7 V to 3.6 V 2 1.4 V to 1.95 V VCCI x 0.35 1.95 V to 2.7 V 0.7 2.7 V to 3.6 V 0.8 1.4 V to 1.95 V VCCB x 0.65 1.95 V to 2.7 V 1.7 2.7 V to 3.6 V 2 1.4 V to 1.95 V VCCB x 0.35 1.95 V to 2.7 V 0.7 2.7 V to 3.6 V 0.8 0 VCCO 3-state 0 3.6 Input transition rise or fall rate TA Operating free-air temperature 1.4 V to 1.6 V -2 1.65 V to 1.95 V -4 2.3 V to 2.7 V -8 3 V to 3.6 V -12 1.4 V to 1.6 V 2 1.65 V to 1.95 V 4 2.3 V to 2.7 V 8 3 V to 3.6 V 12 -40 V V Active state Low-level output current UNIT V 3.6 t/v (1) (2) (3) 1.4 V to 1.95 V 0 High-level output current IOL VCCO V V V mA mA 5 ns/V 85 C VCCI is the VCC associated with the data input port. VCCO is the VCC associated with the data output port. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 5 SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 Electrical Characteristics (1) (2) over operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL II Control inputs A port Ioff B port TEST CONDITIONS B port A port ICCA MIN TYP (3) MAX VI = VIH 1.4 V to 3.6 V 1.4 V to 3.6 V IOH = -2 mA VI = VIH 1.4 V 1.4 V IOH = -4 mA VI = VIH 1.65 V 1.65 V 1.2 IOH = -8 mA VI = VIH 2.3 V 2.3 V 1.75 IOH = -12 mA VI = VIH 3V 3V 2.3 IOH = 100 A VI = VIL 1.4 V to 3.6 V 1.4 V to 3.6 V 0.2 IOH = 2 mA VI = VIL 1.4 V 1.4 V 0.35 IOH = 4 mA VI = VIL 1.65 V 1.65 V 0.45 IOH = 8 mA VI = VIL 2.3 V 2.3 V 0.55 IOH = 12 mA VI = VIL 3V 3V 0.7 1.4 V to 3.6 V 3.6 V 2.5 0V 0 to 3.6 V 10 0 to 3.6 V 0V 10 3.6 V 3.6 V 12.5 0V 3.6 V 12.5 3.6 V 0V 12.5 1.6 V 1.6 V 20 1.95 V 1.95 V 20 2.7 V 2.7 V 30 0V 3.6 V -40 3.6 V 0V 40 3.6 V 3.6 V 40 VI = VCCB or GND VI or VO = 0 to 3.6 V VO = VCCO or GND, VI = VCCI or GND VI = VCCI or GND, ICCB VCCB IOH = -100 A A or B ports IOZ (4) VCCA VI = VCCI or GND, OE = VIH OE = don't care IO = 0 IO = 0 UNIT VCCO - 0.2 1.05 V 1.6 V 1.6 V 20 1.95 V 1.95 V 20 2.7 V 2.7 V 30 0V 3.6 V 40 3.6 V 0V -40 3.6 V 3.6 V 40 V A A A A A Ci Control inputs VI = 3.3 V or GND 3.3 V 3.3 V 4 pF Cio A or B ports VO = 3.3 V or GND 3.3 V 3.3 V 5 pF (1) (2) (3) (4) 6 VCCO is the VCC associated with the output port. VCCI is the VCC associated with the input port. All typical values are at TA = 25C. For I/O ports, the parameter IOZ includes the input leakage current. SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.5 V 0.1 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B ten OE tdis OE VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MIN MAX MIN MAX MIN MAX MIN MAX B 1.7 6.7 1.9 6.3 1.8 5.5 1.7 5.8 A 1.8 6.8 2.2 7.4 2.1 7.6 2.1 7.3 A 2.5 8.4 2.4 7.4 2.1 5.2 1.9 4.2 B 2.1 9 2.9 9.8 3.2 10 3 9.8 A 2.2 6.9 2.3 6.1 1.3 3.6 1.3 3 B 2.1 7.1 2.3 6.4 1.7 5.1 1.6 4.8 UNIT ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.8 V 0.15 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B ten OE tdis OE VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MIN MAX MIN MAX MIN MAX MIN MAX B 1.7 6.7 1.8 6 1.7 4.7 1.6 4.3 A 1.4 5.5 1.8 6 1.8 5.8 1.8 5.5 A 2.6 8.5 2.5 7.5 2.2 5.3 1.9 4.2 B 1.8 7.6 2.6 7.7 2.6 7.6 2.6 7.4 A 2.3 7 2.3 6.1 1.3 3.6 1.3 3 B 1.8 7 2.5 6.3 1.8 4.7 1.7 4.4 UNIT ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 2.5 V 0.2 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B B A ten OE tdis OE VCCB = 1.5 V 0.1 V MIN VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MAX MIN MAX MIN MAX MIN MAX 1.6 6 1.8 5.6 1.5 4 1.4 3.4 1.3 4.6 1.7 4.4 1.5 4 1.4 3.7 A 3.1 8.5 2.5 7.5 2.2 5.3 1.9 4.2 B 1.7 5.7 2.2 5.5 2.2 5.3 2.2 5.1 A 2.4 7 3 6.1 1.4 3.6 1.2 3 B 1.2 5.8 1.9 5 1.4 3.6 1.3 3.3 UNIT ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 3.3 V 0.3 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B ten OE tdis OE VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MIN MAX MIN MAX MIN MAX MIN MAX B 1.5 5.9 1.7 5.4 1.5 3.7 1.4 3.1 A 1.3 4.5 1.6 3.8 1.5 3.3 1.4 3.1 A 2.6 8.3 2.5 7.4 2.2 5.2 1.9 4.1 B 1.6 4.9 2 4.5 2 4.3 1.9 4.1 A 2.3 7 3 6 1.3 3.5 1.2 3.5 B 1.3 6.9 2.1 5.5 1.6 3.8 1.5 3.5 UNIT ns ns ns 7 SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 Operating Characteristics VCCA and VCCB = 3.3 V, TA = 25C PARAMETER TEST CONDITIONS Power dissipation capacitance per transceiver, A-port input, B-port output CpdA (VCCA) CpdB (VCCB) TYP Outputs enabled Outputs disabled CL = 0, 7 f = 10 MHz Power dissipation capacitance per transceiver, B-port input, A-port output Outputs enabled Outputs disabled 7 Power dissipation capacitance per transceiver, A-port input, B-port output Outputs enabled 20 Power dissipation capacitance per transceiver, B-port input, A-port output Outputs enabled Outputs disabled UNIT 14 CL = 0, 20 7 f = 10 MHz 14 Outputs disabled pF pF 7 Output Description The DOCTM circuitry is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical VOL vs IOL and VOH vs IOH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOCTM) Circuitry Technology and Applications, literature number SCEA009. 3.2 TA = 25C Process = Nominal - Output Voltage - V 2.8 2.4 VCC = 3.3 V 2.0 1.6 VCC = 2.5 V 1.2 OH VCC = 1.8 V 0.8 V VOL - Output Voltage - V 2.8 TA = 25C Process = Nominal 2.4 2.0 1.6 1.2 0.8 VCC = 3.3 V 0.4 0.4 0 17 34 51 68 85 102 119 IOL - Output Current - mA 136 153 170 VCC = 2.5 V -160 -144 -128 -112 -96 -80 -64 -48 IOH - Output Current - mA Figure 1. Typical Output Voltage vs Output Current 8 VCC = 1.8 V -32 -16 0 SN74AVCB164245 16-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES394D - JUNE 2002 - REVISED JUNE 2005 PARAMETER MEASUREMENT INFORMATION 2 x VCCO S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCCO GND RL tw LOAD CIRCUIT VCCI VCCI/2 Input VCCO CL RL VTP 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 15 pF 30 pF 30 pF 30 pF 2 k 1 k 500 500 0.1 V 0.15 V 0.15 V 0.3 V VCCI/2 0V VOLTAGE WAVEFORMS PULSE DURATION VCCB Output Control (low-level enabling) VCCB/2 VCCB/2 0V tPZL VCCI Input VCCI/2 VCCI/2 0V tPLH Output tPHL VCCO/2 VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOH VCCO/2 VOL tPLZ VCCO Output Waveform 1 S1 at 2 x VCCO (see Note B) VCCO/2 VOL + VTP VOL tPZH Output Waveform 2 S1 at GND (see Note B) tPHZ VCCO/2 VOH - VTP VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR10 MHz, ZO = 50 , dv/dt 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. VCCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. Figure 2. Load Circuit and Voltage Waveforms 9 PACKAGE OPTION ADDENDUM www.ti.com 3-May-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish SNPB MSL Peak Temp (3) Samples (Requires Login) 74AVCB164245GRDR LIFEBUY BGA MICROSTAR JUNIOR GRD 54 1000 TBD Level-1-240C-UNLIM 74AVCB164245GRE4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AVCB164245GRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AVCB164245VRE4 ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AVCB164245VRG4 ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AVCB164245ZQLR ACTIVE BGA MICROSTAR JUNIOR ZQL 56 1000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM 74AVCB164245ZRDR ACTIVE BGA MICROSTAR JUNIOR ZRD 54 1000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM SN74AVCB164245GR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) SN74AVCB164245KR LIFEBUY BGA MICROSTAR JUNIOR GQL 56 1000 TBD SN74AVCB164245VR ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNPB Level-1-240C-UNLIM CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 3-May-2012 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74AVCB164245 : * Automotive: SN74AVCB164245-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 74AVCB164245GRDR BGA MI CROSTA R JUNI OR GRD 54 1000 330.0 16.4 5.8 8.3 1.55 8.0 16.0 Q1 74AVCB164245ZQLR BGA MI CROSTA R JUNI OR ZQL 56 1000 330.0 16.4 4.8 7.3 1.5 8.0 16.0 Q1 74AVCB164245ZRDR BGA MI CROSTA R JUNI OR ZRD 54 1000 330.0 16.4 5.8 8.3 1.55 8.0 16.0 Q1 SN74AVCB164245GR TSSOP DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1 SN74AVCB164245KR BGA MI CROSTA R JUNI OR GQL 56 1000 330.0 16.4 4.8 7.3 1.45 8.0 16.0 Q1 SN74AVCB164245VR TVSOP DGV 48 2000 330.0 16.4 7.1 10.2 1.6 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 74AVCB164245GRDR BGA MICROSTAR JUNIOR GRD 54 1000 333.2 345.9 28.6 74AVCB164245ZQLR BGA MICROSTAR JUNIOR ZQL 56 1000 333.2 345.9 28.6 74AVCB164245ZRDR BGA MICROSTAR JUNIOR ZRD 54 1000 333.2 345.9 28.6 SN74AVCB164245GR TSSOP DGG 48 2000 367.0 367.0 45.0 SN74AVCB164245KR BGA MICROSTAR JUNIOR GQL 56 1000 333.2 345.9 28.6 SN74AVCB164245VR TVSOP DGV 48 2000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MPDS006C - FEBRUARY 1996 - REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0-8 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins - MO-153 14/16/20/56 Pins - MO-194 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated