TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 D D D D D D Output Swing Includes Both Supply Rails Low Noise . . . 19 nV/Hz Typ at f = 1 kHz Low Input Bias Current . . . 1 pA Typ Fully Specified for Both Single-Supply and Split-Supply Operation Very Low Power . . . 35 A Per Channel Typ Common-Mode Input Voltage Range Includes Negative Rail D D D D Low Input Offset Voltage 850 V Max at TA = 25C (TLC225xA) Macromodel Included Performance Upgrades for the TS27L2/L4 and TLC27L2/L4 Available in Q-Temp Automotive HighRel Automotive Applications Configuration Control / Print Support Qualification to Automotive Standards description 60 V n - Equivalent Input Noise Voltage - nV/ VN nv//HzHz The TLC2252 and TLC2254 are dual and quadruple operational amplifiers from Texas Instruments. Both devices exhibit rail-to-rail output performance for increased dynamic range in single- or split-supply applications. The TLC225x family consumes only 35 A of supply current per channel. This micropower operation makes them good choices for battery-powered applications. The noise performance has been dramatically improved over previous generations of CMOS amplifiers. Looking at Figure 1, the TLC225x has a noise level of 19 nV/Hz at 1kHz; four times lower than competitive micropower solutions. EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY VDD = 5 V RS = 20 T = 25C 50 A 40 30 20 10 The TLC225x amplifiers, exhibiting high input impedance and low noise, are excellent for small-signal conditioning for high-impedance 0 sources, such as piezoelectric transducers. 101 10 2 10 3 10 4 Because of the micropower dissipation levels, f - Frequency - Hz these devices work well in hand-held monitoring Figure 1 and remote-sensing applications. In addition, the rail-to-rail output feature with single or split supplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the TLC225xA family is available and has a maximum input offset voltage of 850 V. This family is fully characterized at 5 V and 5 V. The TLC2252/4 also makes great upgrades to the TLC27L2/L4 or TS27L2/L4 in standard designs. They offer increased output dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature set allows them to be used in a wider range of applications. For applications that require higher output drive and wider input voltage ranges, see the TLV2432 and TLV2442 devices. If the design requires single amplifiers, please see the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal for high density, battery-powered equipment. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Advanced LinCMOS is a trademark of Texas Instruments. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TLC2252 AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax AT 25C 0C to 70C 1500 V TLC2252CD -- -- - 40C to 125C 850 V 1500 V TLC2252AID TLC2252ID -- -- -- -- - 40C to 125C 850 V 1500 V TLC2252AQD TLC2252QD -- -- -- -- - 55C to 125C 850 V 1500 V -- -- TLC2252AMFK TLC2252MFK TLC2252AMJG TLC2252MJG SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (JG) PLASTIC DIP (P) TSSOP (PW) CERAMIC FLATPACK (U) TLC2252CP TLC2252CPW -- TLC2252AIP TLC2252IP TLC2252AIPW -- -- -- -- -- -- -- -- -- -- -- -- -- TLC2252AMU TLC2252MU The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2262CDR). The PW package is available only left-ended taped and reeled. Chip forms are tested at 25C only. TLC2254 AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax AT 25C 0C to 70C 1500 V TLC2254CD -- -- - 40C to 125C 850 V 1500 V TLC2254AID TLC2254ID -- -- -- -- - 40C to 125C 850 V 1500 V TLC2254AQD TLC2254QD -- -- -- -- - 55C to 125C 850 V 1500 V SMALL OUTLINE (D) -- -- CHIP CARRIER (FK) CERAMIC DIP (J) TLC2254AMFK TLC2254MFK TSSOP (PW) CERAMIC FLATPACK (W) TLC2254CN TLC2254CPW -- TLC2254AIN TLC2254IN TLC2254AIPW -- PLASTIC DIP (N) TLC2254AMJ TLC2254MJ -- -- -- -- -- -- -- -- -- -- -- TLC2254AMW -- TLC2254MW The D packages are available taped and reeled. Add R suffix to the device type (e.g., TLC2254CDR). The PW package is available only left-end taped and reeled. Chips are tested at 25C. Chip forms are tested at 25C only. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TLC2252C, TLC2252AC TLC2252I, TLC2252AI TLC2252Q, TLC2252AQ D, P, OR PW PACKAGE (TOP VIEW) 1 8 2 7 3 6 4 5 NC 1OUT NC VDD+ NC VDD + 2OUT 2IN - 2IN + NC 1IN - NC 1IN + NC 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2OUT NC 2IN - NC NC VDD- /GND NC 2IN+ NC 1OUT 1IN - 1IN + VDD - /GND TLC2252M, TLC2252AM . . . FK PACKAGE (TOP VIEW) TLC2252M, TLC2252AM . . . JG PACKAGE (TOP VIEW) 1 8 2 7 3 6 4 5 VDD + 2OUT 2IN - 2IN + NC 1OUT 1IN - 1IN + VCC - /GND TLC2254C, TLC2254AC TLC2254I, TLC2254AI TLC2254Q, TLC2254AQ D, N, OR PW PACKAGE TLC2254M, TLC2254AM J OR W PACKAGE (TOP VIEW) (TOP VIEW) 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN - 4IN + VDD - / GND 3IN + 3IN - 3OUT 1OUT 1IN - 1IN + VDD + 2IN + 2IN - 2OUT 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN - 4IN + VDD - / GND 3IN + 3IN - 3OUT 10 9 3 8 4 7 5 6 NC VCC + 2OUT 2IN - 2IN + TLC2254M, TLC2254AM FK PACKAGE (TOP VIEW) 1IN + NC VCC + NC 2IN + 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4IN + NC VCC - /GND NC 3IN + 2IN - 2OUT NC 3OUT 3IN - 1OUT 1IN - 1IN + VDD + 2IN + 2IN - 2OUT 1 2 1IN - 1OUT NC 4OUT 4IN - 1OUT 1IN - 1IN + VDD - /GND TLC2262M, TLC2252AM . . . U PACKAGE (TOP VIEW) NC - No internal connection POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 equivalent schematic (each amplifier) VDD + Q3 Q6 Q9 Q12 Q14 Q16 R6 IN + OUT C1 IN - R5 Q1 Q4 Q13 Q15 Q17 D1 Q2 Q5 R3 R4 Q7 Q8 Q10 Q11 R1 VDD - / GND ACTUAL DEVICE COMPONENT COUNT COMPONENT TLC2252 TLC2254 Transistors 38 76 Resistors 30 56 9 18 Diodes Capacitors 3 6 Includes both amplifiers and all ESD, bias, and trim circuitry 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 R2 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Supply voltage, VDD - (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 8 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V Input voltage, VI (any input, see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Total current into VDD + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Total current out of VDD - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Duration of short-circuit current at (or below) 25C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 125C Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 125C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55C to 125C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD - . 2. Differential voltages are at IN+ with respect to IN -. Excessive current flows when input is brought below VDD - - 0.3 V. 3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING TA = 125C POWER RATING D-8 724 mW 5.8 mW/C 464 mW 377 mW 144 mW D-14 950 mW 7.6 mW/C 608 mW 450 mW 190 mW FK 1375 mW 11.0 mW/C 880 mW 715 mW 275 mW J 1375 mW 11.0 mW/C 880 mW 715 mW 275 mW JG 1050 mW 8.4 mW/C 672 mW 546 mW 275 mW N 1150 mW 9.2 mW/C 736 mW 736 mW -- P 1000 mW 8.0 mW/C 640 mW 520 mW -- PW-8 525 mW 4.2 mW/C 336 mW 273 mW -- PW-14 700 mW 5.6 mW/C 448 mW 448 mW -- U 700 mW 5.5 mW/C 246 mW 330 mW 150 mW W 700 mW 5.5 mW/C 246 mW 330 mW 150 mW recommended operating conditions C SUFFIX MIN Supply voltage, VDD 2.2 Input voltage range, VI Common-mode input voltage, VIC VDD - VDD - Operating free-air temperature, TA 0 MAX 8 VDD + - 1.5 VDD + - 1.5 70 I SUFFIX MIN 2.2 VDD - VDD - - 40 POST OFFICE BOX 655303 MAX 8 VDD + - 1.5 VDD + - 1.5 125 Q SUFFIX MIN 2.2 VDD - VDD - - 40 * DALLAS, TEXAS 75265 MAX 8 VDD + - 1.5 VDD + - 1.5 125 M SUFFIX MIN 2.2 VDD - VDD - - 55 MAX UNIT 8 V VDD + - 1.5 VDD + - 1.5 V 125 C V 5 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage IIB Input bias current VICR VDD = 2.5 V, RS = 50 VIC = 0, VO = 0 0, rid 1500 25C 0.003 25C 0.5 1 RS = 50 , Common mode input voltage range Common-mode Low-level output voltage Large-signal g g differential voltage g amplification Full range g 0 to 3.5 25C IOH = - 75 A High level output voltage High-level 0 to 4 |VIO | 5 mV IOL = 50 A IOL = 500 A 4.9 Full range 4.8 25C 4.8 0.01 0.09 Full range Full range 5V VIC = 2 2.5 V, IOL = 4 mA Full range Differential input resistance V 4.88 25C mA pA V 4.94 25C IOL = 1 RL = 100 k VIC = 2.5 2 5 V, V VO = 1 V to 4 V RL = 1 M - 0.3 to 4.2 pA 4.98 25C VIC = 2 2.5 5V V, 60 100 25C V V/mo 60 100 25C UNIT V/C 05 0.5 Full range VIC = 2 2.5 5V V, AVD 200 Full range IOH = - 150 A VIC = 2.5 V, VOL MAX 1750 25C to 70C IOH = - 20 A VOH TYP Full range Input offset voltage long-term drift (see Note 4) Input offset current TLC2252C MIN 25C VIO IIO TA 0.15 0.15 25C 0.2 0.3 V 0.3 25C 0.7 1 1.2 25C 100 Full range 10 350 V/mV 25C 1700 25C 1012 ric Common-mode input resistance 25C 1012 cic Common-mode input capacitance f = 10 kHz, P package 25C 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 200 CMRR Common mode rejection ratio Common-mode VIC = 0 to 2.7 V,, RS = 50 kSVR Supply voltage rejection ratio (VDD/VIO) Supply-voltage VDD = 4.4 V to 16 V,, VIC = VDD /2, No load IDD Supply current VO = 2 2.5 5V V, VO = 2.5 V,, No load 25C 70 Full range 70 25C 80 Full range 80 25C Full range 83 dB 95 70 dB 125 150 A Full range is 0C to 70C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR TEST CONDITIONS VO = 1 1.5 5 V to 3 3.5 5V V, RL = 100 k, CL = 100 pF F Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion plus noise Gain-bandwidth product BOM Maximum output-swing bandwidth m Phase margin at unity gain Gain margin TA TLC2252C MIN TYP 25C 0.07 0.12 Full range 0 05 0.05 25C 36 f = 1 kHz 25C 19 f = 0.1 Hz to 1 Hz 25C 0.7 f = 0.1 Hz to 10 Hz 25C 1.1 25C 0.6 AV = 1 VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF RL = 50 k, CL = 100 pF nV/Hz V fAHz 0.2% 25C AV = 10 RL = 50 k, UNIT V/s f = 10 Hz VO = 0.5 V to 2.5 V, f = 10 kHz kHz, RL = 50 k f = 10 kHz, CL = 100 pF MAX 1% 25C 0.2 MHz 25C 30 kHz 25C 63 25C 15 dB Full range is 0C to 70C. Referenced to 2.5 V POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise specified) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage IIB Input bias current VICR 200 1500 VIC = 0, RS = 50 VO = 0, 25C 0.003 V/mo 25C 0.5 1 IO = - 200 A VIC = 0, Maximum negative peak output voltage Large-signal differential voltage amplification IO = 50 A IO = 500 A VIC = 0 0, -5 to 4 Full range g -5 to 3.5 25C IO = - 100 A 25C 4.9 4.7 25C 4.8 25C - 4.85 Full range - 4.85 25C - 4.7 - 4.7 mA Full range VIC = 0 0, IO = 4 mA Full range VO = 4 V RL = 100 k RL = 1 M 25C pA V 4.93 V 4.86 - 4.99 25C IO = 1 - 5.3 to 4.2 pA 4.98 Full range VIC = 0 0, 60 100 25C RS = 50 60 100 Full range |VIO | 5 mV mV, V V/C 25C Common mode input voltage range Common-mode UNIT 05 0.5 Full range VOM + Maximum positive peak output voltage AVD MAX 1750 25C to 70C IO = - 20 A VOM - TYP Full range Input offset voltage long-term drift (see Note 4) Input offset current TLC2252C MIN 25C VIO IIO TA -4 - 4.91 V - 4.8 - 4.3 - 3.8 25C 45 Full range 10 650 V/mV 25C 3000 rid Differential input resistance 25C 1012 ric Common-mode input resistance 25C 1012 cic Common-mode input capacitance f = 10 kHz, 25C 8 pF zo Closed-loop output impedance f = 25 kHz, 25C 190 P package AV = 10 VIC = - 5 V to 2.7 V, CMRR Common-mode Common mode rejection ratio kSVR Supply voltage rejection ratio (VDD /VIO) Supply-voltage IDD Supply current 25C 75 VO = 0, RS = 50 VDD = 2.2 V to 8 V, Full range 75 25C 80 VIC = 0, No load Full range 80 VO = 0 0, No load 25C Full range 88 dB 95 80 dB 125 150 A Full range is 0C to 70C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VO = 1 1.9 9V V, CL = 100 pF SR Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion pulse duration Gain-bandwidth product BOM Maximum output-swing bandwidth m Phase margin at unity gain Gain margin RL = 100 k k, TA TLC2252C MIN TYP 25C 0.07 0.12 Full range 0.05 25C 38 f = 1 kHz 25C 19 f = 0.1 Hz to 1 Hz 25C 0.8 f = 0.1 Hz to 10 Hz 25C 1.1 25C 0.6 AV = 1 VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF RL = 50 k, k CL = 100 pF nV/Hz V fAHz 0.2% 25C AV = 10 RL = 50 k, UNIT V/s f = 10 Hz VO = 2.3 V, f = 10 kHz kHz, RL = 50 k f = 10 kHz, CL = 100 pF MAX 1% 25C 0.21 MHz 25C 14 kHz 25C 63 25C 15 dB Full range is 0C to 70C. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage IIB Input bias current VICR VOL MAX 200 1500 1750 25C to 70C VDD = 2.5 V, RS = 50 VIC = 0, VO = 0 0, 25C 0.003 V/mo 25C 0.5 1 Low-level output voltage 0 to 4 Full range 0 to 3.5 25C IOH = - 75 A High level output voltage High-level IOH = - 150 A VIC = 2.5 V, IOL = 50 A VIC = 2 2.5 5V V, IOL = 500 A VIC = 2 2.5 5V V, VIC = 2 2.5 5V V, IOL = 1 mA IOL = 4 mA RL = 100 k VIC = 2.5 2 5 V, V VO = 1 V to 4 V RL = 1 M 4.9 Full range 4.8 25C 4.8 25C 0.09 Full range 0.2 Full range 0.7 Full range 25C 100 10 Common-mode input resistance Common-mode input capacitance f = 10 kHz, N package zo Closed-loop output impedance f = 25 kHz, AV = 10 25C V 1 1.2 Full range ci(c) 0.3 0.3 25C ri(c) 0.15 0.15 25C Differential input resistance V 4.88 0.01 ri(d) pA V 4.94 25C Large-signal g g differential voltage g amplification 350 V/mV 25C 1700 25C 1012 25C 1012 25C 8 pF 200 25C 70 CMRR Common mode rejection ratio Common-mode VIC = 0 to 2.7 V,, VO = 2.5 V,, RS = 50 Full range 70 kSVR Supply voltage rejection ratio (VDD /VIO) Supply-voltage VDD = 4.4 V to 16 V,, VIC = VDD /2, No load 25C 80 Full range 80 IDD Supply current (four amplifiers) VO = 2 2.5 5V V, No load - 0.3 to 4.2 pA 4.98 25C AVD 60 100 25C |VIO | 5 mV 60 100 Full range RS = 50 , V V/C 25C Common mode input voltage range Common-mode UNIT 0.5 Full range IOH = - 20 A VOH TYP Full range Input offset voltage long-term drift (see Note 4) Input offset current TLC2254C MIN 25C VIO IIO TA 25C Full range 83 dB 95 140 dB 250 300 A Full range is 0C to 70C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak-to-peak equivalent input noise q voltage In Equivalent input noise current THD + N Total harmonic distortion plus noise TEST CONDITIONS VO = 1.4 V to 2.6 V CL = 100 pF RL = 100 k, TLC2254C MIN TYP 25C 0.07 0.12 Full range 0.05 f = 10 Hz 25C 36 f = 1 kHz 25C 19 f = 0.1 Hz to 1 Hz 25C 0.7 f = 0.1 Hz to 10 Hz 25C 1.1 25C 0.6 VO = 0.5 V to 2.5 V, f = 10 kHz kHz, RL = 50 k AV = 1 Gain-bandwidth product f = 10 kHz, CL = 100 pF RL = 50 k, BOM Maximum output-swing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF m Phase margin at unity gain RL = 50 k, CL = 100 pF Gain margin TA MAX UNIT V/s nV/Hz V fA /Hz 0.2% 25C AV = 10 1% 25C 0.2 MHz 25C 30 kHz 25C 63 25C 15 dB Full range is 0C to 70C. Referenced to 2.5 V POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise specified) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage IIB Input bias current VICR MAX 200 1500 1750 25C to 70C VIC = 0, RS = 50 VO = 0, 25C 0.003 25C 0.5 25C 1 |VIO | 5 mV mV, Common mode input voltage range Common-mode IO = - 200 A VIC = 0, Maximum negative peak output voltage IO = 50 A VIC = 0 0, IO = 500 A VIC = 0 0, IO = 1 mA VIC = 0 0, IO = 4 mA VO = 4 V Full range -5 to 3.5 25C IO = - 100 A VOM + Maximum positive peak output voltage -5 to 4 RS = 50 RL = 100 k 4.9 Full range 4.7 25C 4.8 25C - 4.85 Full range - 4.85 25C - 4.7 Full range - 4.7 40 10 ri(d) Differential input resistance ri(c) Common-mode input resistance ci(c) Common-mode input capacitance f = 10 kHz, N package zo Closed-loop output impedance f = 25 kHz, AV = 10 25C CMRR Common-mode Common mode rejection ratio 150 V/mV 1012 8 pF 190 25C 80 80 No load - 4.3 25C Full range VO = 0 0, V - 4.8 25C 75 Supply current (four amplifiers) - 4.91 1012 Full range IDD 4.86 3000 VIC = - 5 V to 2.7 V,, VO = 0, RS = 50 VDD = 2.2 V to 8 V,, VIC = 0, No load V 25C 75 Supply voltage rejection ratio (VDD /VIO) Supply-voltage 4.93 25C 25C kSVR V - 3.8 Full range Large-signal differential voltage amplification RL = 1 M -4 25C AVD pA - 4.99 25C Full range - 5.3 to 4.2 pA 4.98 25C 25C 60 100 25C V V/mo 60 100 Full range UNIT V/C 0.5 Full range IO = - 20 A VOM - TYP Full range Input offset voltage long-term drift (see Note 4) Input offset current TLC2254C MIN 25C VIO IIO TA 25C Full range 88 dB 95 160 dB 250 300 A Full range is 0C to 70C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VO = 1.9 V,, CL = 100 pF SR Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion plus noise RL = 100 k,, TLC2254C MIN TYP 25C 0.07 0.12 Full range 0.05 f = 10 Hz 25C 38 f = 1 kHz 25C 19 f = 0.1 Hz to 1 Hz 25C 0.8 f = 0.1 Hz to 10 Hz 25C 1.1 25C 0.6 VO = 2.3 V, f = 20 kHz kHz, RL = 50 k AV = 1 Gain-bandwidth product f = 10 kHz, CL = 100 pF RL = 50 k, BOM Maximum output-swing bandwidth VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF m Phase margin at unity gain RL = 50 k, k CL = 100 pF Gain margin Full range is 0C to 70C. TA POST OFFICE BOX 655303 UNIT V/s nV/Hz V fA /Hz 0.2% 25C AV = 10 * DALLAS, TEXAS 75265 MAX 1% 25C 0.21 MHz 25C 14 kHz 25C 63 25C 15 dB 13 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range TA TEST CONDITIONS 25C High-level output g voltage Low level output Low-level voltage Large signal differential Large-signal lification voltage am amplification 1500 5V VIC = 2 2.5 V, IOL = 500 A IOL = 4 mA RL = 100 k 5V VIC = 2 2.5 V, VO = 1 V to 4 V RL = 1 M 850 1000 UNIT V 25C 0.003 0.003 V/mo 25C 0.5 60 0.5 1000 1 25C 0 to 4 60 Full range 0 to 3.5 - 0.3 to 4.2 1 4.9 Full range 4.8 25C 4.8 0 to 4 - 0.3 to 4.2 4.9 4.94 4.88 0.09 Full range 4.8 4.88 0.01 0.15 0.09 0.15 0.8 Full range 100 Full range 10 350 0.15 0.15 1 0.7 1.2 25C V 4.8 25C pA 4.98 4.94 0.01 pA V 0 to 3.5 25C 25C 60 1000 4.98 25C 60 1000 1000 25C IOL = 50 A 200 MAX V/C |VIO | 5 mV IOH = - 75 A TYP 0.5 25C RS = 50 , MIN 0.5 Full range VIC = 2 2.5 5V V, AVD 200 Full range IOH = - 150 A VIC = 2.5 V, VOL MAX 1750 25C to 85C VDD = 2.5 V V, VO = 0, VIC = 0, RS = 50 TLC2252AI TYP Full range IOH = - 20 A VOH TLC2252I MIN V 1 1.2 100 350 10 V/mV 25C 1700 1700 rid Differential input resistance 25C 1012 1012 ric Common-mode input resistance 25C 1012 1012 cic Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 200 200 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V,, VO = 2.5 V,, RS = 50 kSVR Supply-voltage rejection ratio (VDD /VIO) VDD = 4.4 V to 16 V, VIC = VDD /2, No load IDD Supply Su ly current VO = 2 2.5 5V V, No load 25C 70 Full range 70 25C 80 Full range 80 83 70 83 dB 70 95 80 95 dB 25C Full range 80 70 125 150 70 125 150 A Full range is - 40C to 125C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC2252I MIN TYP 25C 0.07 0.12 Full range 0.05 TLC2252AI MAX MIN TYP 0.07 0.12 MAX UNIT SR Slew rate at unity gain VO = 1.5 V to 3.5 V,, RL = 100 k, CL = 100 pF Vn Equivalent input q noise voltage f = 10 Hz 25C 36 36 f = 1 kHz 25C 19 19 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 10 kHz kHz, RL = 50 k AV = 1 0.2% 0.2% THD + N 1% 1% Gain-bandwidth product f = 50 kHz, CL = 100 pF RL = 50 k, 25C 0.2 0.2 MHz BOM Maximum outputswing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, RL = 50 k, 25C 30 30 kHz m Phase margin at unity gain RL = 50 k, CL = 100 pF 25C 63 63 25C 15 15 POST OFFICE BOX 655303 nV/Hz V fAHz 25C AV = 10 Gain margin Full range is - 40C to 125C. Referenced to 2.5 V V/s 0.05 * DALLAS, TEXAS 75265 dB 15 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage longterm drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range TA TEST CONDITIONS 25C VO = 0, VOM - Large-signal L i l diff differential ti l voltage am lification amplification 1500 IO = 4 VO = 4 V mA RL = 50 k V 0.003 0.003 V/mo 25C 0.5 1 Full range -5 to 3.5 60 - 5.3 to 4.2 4.9 Full range 4.7 25C 4.8 25C 1 - 4.85 Full range - 4.85 -4 -5 to 4 25C 40 10 - 5.3 to 4.2 pA pA V -5 to 3.5 4.98 4.93 4.9 4.93 V 4.7 4.86 4.8 4.86 - 4.99 - 4.91 - 4.85 - 4.91 V - 4.85 - 4.3 -4 - 3.8 Full range 60 1000 - 4.99 25C 60 1000 4.98 25C Full range 0.5 1000 -5 to 4 25C 60 1000 25C RL = 1 M 850 1000 UNIT 25C 25C IO = 500 A VIC = 0 0, 200 MAX V/C |VIO | 5 mV IO = - 100 A TYP 0.5 25C RS = 50 , MIN 0.5 Full range VIC = 0 0, AVD 200 Full range IO = - 200 A VIC = 0, IO = 50 A Maximum M i negative ti peak eak out output ut voltage MAX 1750 25C to 85C VIC = 0, RS = 50 TLC2252AI TYP Full range IO = - 20 A Maximum positive peak VOM + output voltage TLC2252I MIN - 4.3 - 3.8 150 40 150 V/mV 10 25C 3000 3000 rid Differential input resistance 25C 1012 1012 ric Common-mode input resistance 25C 1012 1012 cic Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 190 190 CMRR Common-mode rejection ratio VIC = - 5 V to 2.7 V,, VO = 0, RS = 50 25C 75 Full range 75 kSVR Supply-voltage y g rejection j ratio (VDD /VIO) VDD = 4.4 V to 16 V,, VIC = VDD /2, No load 25C 80 Full range 80 IDD Supply current 5V VO = 2 2.5 V, No load 25C Full range 88 75 88 dB 75 95 80 95 dB 80 80 125 150 80 125 150 A Full range is - 40C to 125C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VO = 1 1.9 9V V, CL = 100 pF RL = 100 k k, TA TLC2252I MIN TYP 25C 0.07 0.12 Full range 0.05 TLC2252AI MAX MIN TYP 0.07 0.12 MAX UNIT SR Slew rate at unity gain Vn Equivalent input noise q voltage f = 10 Hz 25C 38 38 f = 1 kHz 25C 19 19 VN(PP) Peak-to-peak equivalent q input noise voltage f = 0.1 Hz to 1 Hz 25C 0.8 0.8 f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 2.3 V, RL = 50 k, k f = 10 kHz AV = 1 0.2% 0.2% THD + N 1% 1% Gain-bandwidth product f =10 kHz, CL = 100 pF RL = 50 k, 25C 0.21 0.21 MHz BOM Maximum output-swing bandwidth VO(PP) = 4.6 V,AV = 1, RL = 50 k, CL = 100 pF 25C 14 14 kHz m Phase margin at unity gain RL = 50 k, 25C 63 63 25C 15 15 Gain margin Full range is - 40C to 125C. POST OFFICE BOX 655303 nV/Hz V fAHz 25C AV = 10 CL = 100 pF V/s 0.05 * DALLAS, TEXAS 75265 dB 17 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input In ut offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input In ut offset current IIB Input In ut bias current VICR VOH Common-mode input voltage range High-level g output voltage TEST CONDITIONS AVD Low-level Low level output voltage Large signal Large-signal differential voltage amplification TLC2254I MIN 25C MAX 200 1500 850 1000 UNIT V V/C 25C 0.003 0.003 V/mo 25C 0.5 1 0.5 0 to 4 60 Full range 0 to 3.5 IOH = - 20 A 25C IOH = - 75 A 25C 4.9 Full range 4.8 25C 4.8 - 0.3 to 4.2 1 0 to 4 - 0.3 to 4.2 4.9 4.94 4.88 VIC = 2 2.5 5V V, IOL = 500 A 25C 0.09 5V VIC = 2 2.5 V, IOL = 4 Full range 4.8 4.88 0.01 0.15 0.09 0.15 0.8 Full range 100 10 1 350 0.15 0.15 0.7 1.2 25C V 4.8 0.01 pA A 4.98 4.94 25C pA A V 0 to 3.5 IOL = 50 A Full range 60 1000 4.98 25C 60 1000 1000 25C |VIO | 5 mV 60 1000 25C RL = 100 k VIC = 2 2.5 5V V, VO = 1 V to 4 V RL = 1 M 200 MAX 0.5 Full range mA TYP 0.5 Full range RS = 50 , MIN 1750 25C to 125C VDD = 2.5 V, VIC = 0, VO = 0, RS = 50 TLC2254AI TYP Full range IOH = - 150 A VIC = 2.5 V, VOL TA V 1 1.2 100 350 10 V/mV 25C 1700 1700 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 200 200 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 kSVR Supply-voltage rejection ratio (VDD /VIO) VDD = 4.4 V to 16 V, VIC = VDD /2, No load IDD Supply y current (four amplifiers) VO = 2 2.5 5V V, No load 25C 70 Full range 70 25C 80 Full range 80 83 70 83 dB 70 95 80 95 dB 25C Full range 80 140 250 300 140 250 300 A Full range is - 40C to 125C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC2254I MIN TYP 0.12 TLC2254AI MAX MIN TYP 0.07 0.12 MAX UNIT VO = 1.4 V to 2.6 V,, RL = 100 k, CL = 100 pF 25C 0.07 Full range 0.05 Equivalent input q noise voltage f = 10 Hz 25C 36 36 f = 1 kHz 25C 19 19 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 0.2% 0.2% THD + N 1% 1% Gain-bandwidth product f = 50 kHz, CL = 100 pF RL = 50 k, 25C 0.2 0.2 MHz BOM Maximum outputswing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF 25C 30 30 kHz m Phase margin at unity gain RL = 50 k, CL = 100 pF 25C 63 63 25C 15 15 SR Slew rate at unity gain Vn POST OFFICE BOX 655303 nV/Hz V fA /Hz 25C AV = 10 Gain margin Full range is - 40C to 125C. Referenced to 2.5 V V/s 0.05 * DALLAS, TEXAS 75265 dB 19 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range TA TEST CONDITIONS 25C VO = 0, VOM - Large-signal L i l diff differential ti l voltage am lification amplification 1500 VIC = 0 0, VO = 4 V IO = 4 mA RL = 100 k V 0.003 0.003 V/mo 25C 0.5 1 Full range -5 to 3.5 60 - 5.3 to 4.2 4.9 Full range 4.7 25C 4.8 25C 1 - 4.85 Full range - 4.85 -4 -5 to 4 25C 40 10 - 5.3 to 4.2 pA pA V -5 to 3.5 4.98 4.93 4.9 4.93 V 4.7 4.86 4.8 4.86 - 4.99 - 4.91 - 4.85 - 4.91 V - 4.85 - 4.3 -4 - 3.8 Full range 60 1000 - 4.99 25C 60 1000 4.98 25C Full range 0.5 1000 -5 to 4 25C 60 1000 25C RL = 1 M 850 1000 UNIT 25C 25C IO = 500 A 200 MAX V/C |VIO | 5 mV IO = - 100 A TYP 0.5 25C RS = 50 , MIN 0.5 Full range VIC = 0 0, AVD 200 Full range IO = - 200 A VIC = 0, IO = 50 A Maximum M i negative ti peak k output out ut voltage MAX 1750 25C to 125C VIC = 0, RS = 50 TLC2254AI TYP Full range IO = - 20 A Maximum positive peak VOM + output voltage TLC2254I MIN - 4.3 - 3.8 150 40 150 V/mV 10 25C 3000 3000 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 190 190 CMRR Common-mode rejection j ratio VIC = - 5 V to 2.7 V,, VO = 0, RS = 50 kSVR Supply-voltage y g rejection j ratio (VDD /VIO) VDD = 2.2 V to 8 V,, VIC = VDD /2, No load IDD Supplyy current (four amplifiers) VO = 0 0, No load 25C 75 Full range 75 25C 80 Full range 80 25C Full range 88 75 88 dB 75 95 80 95 dB 80 160 250 300 160 250 300 A Full range is - 40C to 125C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VO = 1 1.9 9V V, CL = 100 pF RL = 100 k k, TA TLC2254I MIN TYP 25C 0.07 0.12 Full range 0.05 TLC2254AI MAX MIN TYP 0.07 0.12 SR Slew rate at unity gain Vn Equivalent input noise q voltage f = 10 Hz 25C 38 38 f = 1 kHz 25C 19 19 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.8 0.8 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 2.3 V, RL = 50 k, k f = 20 kHz AV = 1 0.2% 0.2% THD + N Gain-bandwidth product f =10 kHz, CL = 100 pF RL = 50 k, BOM Maximum output-swing bandwidth VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF m Phase margin at unity gain RL = 50 k, CL = 100 pF POST OFFICE BOX 655303 UNIT V/s 0.05 nV/Hz V fA /Hz 25C AV = 10 Gain margin Full range is - 40C to 125C. MAX 1% 1% 25C 0.21 0.21 MHz 25C 14 14 kHz 25C 63 63 25C 15 15 * DALLAS, TEXAS 75265 dB 21 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TA TEST CONDITIONS TLC2252Q TLC2252M MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range 25C VOH VOL Low-level Low level output voltage Large-signal Large signal differential lification voltage am amplification 200 1500 VIC = 0, RS = 50 0.003 V/mo 25C 0.5 1 25C 0 to 4 Full range 0 to 3.5 1 4.9 Full range 4.8 25C 4.8 0 to 4 - 0.3 to 4.2 4.9 4.94 25C 0.09 Full range 4.88 4.8 4.88 0.01 0.15 0.09 0.15 0.8 Full range 100 Full range 10 350 0.15 0.15 1 0.7 1.2 25C V 4.8 IOL = 500 A pA 4.98 4.94 VIC = 2 2.5 5V V, pA V 0 to 3.5 0.01 25C 60 1000 4.98 25C 60 1000 60 - 0.3 to 4.2 25C RL = 1 M 0.5 1000 IOL = 50 A RL = 100 k 60 1000 IOH = - 150 A VIC = 2.5 V, VIC = 2 2.5 5V V, VO = 1 V to 4 V V 0.003 25C mA 850 1000 25C |VIO | 5 mV IOL = 4 200 UNIT MAX V/C 25C IOH = - 75 A TYP 0.5 Full range RS = 50 , MIN 0.5 Full range 5V VIC = 2 2.5 V, AVD MAX 1750 25C to 125C IOH = - 20 A High-level g output voltage TYP Full range VDD = 2.5 V V, VO = 0, TLC2252AQ TLC2252AM V 1 1.2 100 350 10 V/mV 25C 1700 1700 rid Differential input resistance 25C 1012 1012 ric Common-mode input resistance 25C 1012 1012 cic Common-mode input capacitance f = 10 kHz, f = 10 kHz, 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 200 200 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V,, RS = 50 VO = 2.5 V,, kSVR Supply-voltage rejection ratio (VDD /VIO) VDD = 4.4 V to 16 V, VIC = VDD /2, No load IDD Supply Su ly current VO = 2 2.5 5V V, No load 25C 70 Full range 70 25C 80 Full range 80 83 70 83 dB 70 95 80 95 dB 25C Full range 80 70 125 150 70 125 150 A Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC2252Q TLC2252M MIN TYP 25C 0.07 0.12 Full range 0.05 TLC2252AQ TLC2252AM MAX MIN TYP 0.07 0.12 UNIT MAX SR Slew rate at unity gain VO = 0 0.5 5 V to 3 3.5 5V V, RL = 100 k, Vn Equivalent q input noise voltage f = 10 Hz 25C 36 36 f = 1 kHz 25C 19 19 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 10 kHz kHz, RL = 50 k AV = 1 0.2% 0.2% THD + N 1% 1% Gain-bandwidth product f = 50 kHz, CL = 100 pF RL = 50 k, 25C 0.2 0.2 MHz BOM Maximum outputswing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF 25C 30 30 kHz m Phase margin at unity gain RL = 50 k, CL = 100 pF 25C 63 63 Gain margin 25C Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. Referenced to 2.5 V 15 15 CL = 100 pF nV/Hz V fAHz 25C AV = 10 POST OFFICE BOX 655303 V/s 0.05 * DALLAS, TEXAS 75265 dB 23 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TA TEST CONDITIONS TLC2252Q TLC2252M MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage longterm drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range 25C VO = 0, AVD M i ti Maximum negative eak out ut voltage peak output L i l diff ti l Large-signal differential voltage am lification amplification 200 1500 VIC = 0 0, IO = 4 VO = 4 V mA RL = 100 k 1000 V 0.003 V/mo 25C 0.5 1 Full range -5 to 3.5 60 - 5.3 to 4.2 25C 4.9 4.7 25C 4.8 25C 1 - 4.85 Full range - 4.85 -4 -5 to 4 40 Full range 10 - 5.3 to 4.2 pA pA V -5 to 3.5 4.98 4.93 4.9 4.93 V 4.7 4.86 4.8 4.86 - 4.99 - 4.91 - 4.85 - 4.91 V - 4.85 - 4.3 -4 - 3.8 25C 60 1000 - 4.99 25C 60 1000 4.98 Full range 25C 0.5 1000 -5 to 4 Full range 60 1000 25C RL = 1 M 850 0.003 25C IO = 500 A 200 25C |VIO | 5 mV VIC = 0 0, MAX V/C 25C IO = - 100 A UNIT TYP 0.5 Full range RS = 50 , MIN 0.5 Full range IO = - 200 A VIC = 0, IO = 50 A VOM - MAX 1750 25C to 125C IO = - 20 A Maximum positive peak VOM + output voltage TYP Full range VIC = 0, RS = 50 TLC2252AQ TLC2252AM - 4.3 - 3.8 150 40 150 V/mV 10 25C 3000 3000 rid Differential input resistance 25C 1012 1012 ric Common-mode input resistance 25C 1012 1012 cic Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 190 190 CMRR Common-mode rejection ratio VIC = - 5 V to 2.7 V,, VO = 0, RS = 50 kSVR Supply-voltage y g rejection j ratio (VDD /VIO) VDD = 2.2 V to 8 V,, VIC = 0, No load IDD Supply current VO = 2 2.5 5V V, No load 25C 75 Full range 75 25C 80 Full range 80 25C Full range 88 75 88 dB 75 95 80 95 dB 80 80 125 150 80 125 150 A Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 24 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VO = 2 V V, CL = 100 pF RL = 100 k k, SR Slew rate at unity gain Vn Equivalent q input noise voltage VN(PP) Peak-to-peak equivalent q input noise voltage In Equivalent input noise current THD + N Total harmonic distortion plus noise VO = 2.3 V, RL = 50 k, k f = 10 kHz AV = 1 Gain-bandwidth product f =10 kHz, CL = 100 pF RL = 50 k, BOM Maximum output-swing bandwidth VO(PP) = 4.6 V, AV = 1, RL = 50 k, CL = 100 pF m Phase margin at unity gain RL = 50 k, TA TLC2252Q TLC2252M MIN TYP 25C 0.07 0.12 Full range 0.05 TLC2252AQ TLC2252AM MAX MIN TYP 0.07 0.12 UNIT MAX V/s 0.05 f = 10 Hz 25C 38 38 f = 1 kHz 25C 19 19 f = 0.1 Hz to 1 Hz 25C 0.8 0.8 f = 0.1 Hz to 10 Hz 25C 1.1 1.1 25C 0.6 0.6 0.2% 0.2% 1% 1% 25C 0.21 0.21 MHz 25C 14 14 kHz 25C 63 63 Gain margin 25C Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. 15 15 POST OFFICE BOX 655303 V fAHz 25C AV = 10 CL = 100 pF nV/Hz * DALLAS, TEXAS 75265 dB 25 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA TLC2254Q TLC2254M MIN VIO Input In ut offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input In ut offset current IIB Input In ut bias current VICR VOH Common-mode input voltage range High-level g output voltage 25C Low-level Low level output voltage Large-signal Large signal differential voltage amplification 200 1500 VIC = 0, RS = 50 0.003 V/mo 25C 0.5 1 25C 0 to 4 Full range 0 to 3.5 IOH = - 75 A 4.9 Full range 4.8 25C 4.8 1 0 to 4 - 0.3 to 4.2 4.9 4.94 4.88 IOL = 500 A 0.09 Full range 4.8 4.88 0.01 0.15 0.09 0.15 0.8 Full range Full range 10 350 0.15 0.15 1 0.7 1.2 100 V 4.8 25C pA A 4.98 4.94 0.01 pA A V 0 to 3.5 25C 25C 60 1000 4.98 25C 60 1000 60 - 0.3 to 4.2 IOL = 50 A RL = 1 M 0.5 1000 25C RL = 100 k 60 1000 25C 5V VIC = 2 2.5 V, VO = 1 V to 4 V V 0.003 IOH = - 20 A mA 850 1000 25C |VIO | 5 mV IOL = 4 200 UNIT MAX V/C 25C VIC = 2 2.5 5V V, TYP 0.5 125C RS = 50 , MIN 0.5 125C VIC = 2 2.5 5V V, AVD MAX 1750 25C to 125C IOH = - 150 A VIC = 2.5 V, VOL TYP Full range VDD = 2.5 V, VO = 0, TLC2254AQ TLC2254AM V 1 1.2 100 350 10 V/mV 25C 1700 1700 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 200 200 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 kSVR IDD Supply-voltage rejection ratio (VDD /VIO) Supply y current (four amplifiers) VDD = 4.4 V to 16 V, VIC = VDD /2, No load VO = 2 2.5 5V V, No load 25C 70 Full range 70 25C 80 Full range 80 83 70 83 dB 70 95 80 95 dB 25C Full range 80 140 250 300 140 250 300 A Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 26 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC2254Q TLC2254M MIN TYP 0.12 VO = 0.5 V to 3.5 V,, RL = 100 k, CL = 100 pF 25C 0.07 Full range 0.05 TLC2254AQ TLC2254AM MAX MIN TYP 0.07 0.12 UNIT MAX SR Slew rate at unity gain Vn Equivalent q input noise voltage f = 10 Hz 25C 36 36 f = 1 kHz 25C 19 19 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 0.2% 0.2% THD + N 1% 1% Gain-bandwidth product f = 50 kHz, CL = 100 pF RL = 50 k, 25C 0.2 0.2 MHz BOM Maximum outputswing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF 25C 30 30 kHz m Phase margin at unity gain RL = 50 k, CL = 100 pF 25C 63 63 Gain margin 25C Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. Referenced to 2.5 V 15 15 nV/Hz V fA /Hz 25C AV = 10 POST OFFICE BOX 655303 V/s 0.05 * DALLAS, TEXAS 75265 dB 27 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TA TEST CONDITIONS TLC2254Q TLC2254M MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range 25C VO = 0, AVD M i ti peak k Maximum negative out ut voltage output L i l diff ti l Large-signal differential voltage am lification amplification 200 1500 VIC = 0 0, IO = 4 VO = 4 V mA RL = 100 k 1000 V 0.003 V/mo 25C 0.5 1 Full range -5 to 3.5 60 - 5.3 to 4.2 25C 4.9 4.7 25C 4.8 25C 1 - 4.85 Full range - 4.85 -4 -5 to 4 40 Full range 10 - 5.3 to 4.2 pA pA V -5 to 3.5 4.98 4.93 4.9 4.93 V 4.7 4.86 4.8 4.86 - 4.99 - 4.91 - 4.85 - 4.91 V - 4.85 - 4.3 -4 - 3.8 25C 60 1000 - 4.99 25C 60 1000 4.98 Full range 25C 0.5 1000 -5 to 4 Full range 60 1000 25C RL = 1 M 850 0.003 25C IO = 500 A 200 25C |VIO | 5 mV VIC = 0 0, MAX V/C 25C IO = - 100 A UNIT TYP 0.5 125C RS = 50 , MIN 0.5 125C IO = - 200 A VIC = 0, IO = 50 A VOM - MAX 1750 25C to 125C IO = - 20 A Maximum positive peak VOM + output voltage TYP Full range VIC = 0, RS = 50 TLC2254AQ TLC2254AM - 4.3 - 3.8 150 40 150 V/mV 10 25C 3000 3000 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 25 kHz, AV = 10 25C 190 190 CMRR Common-mode rejection j ratio VIC = - 5 V to 2.7 V,, VO = 0, RS = 50 25C 75 Full range 75 kSVR Supply-voltage y g rejection j ratio (VDD /VIO) VDD = 2.2 V to 8 V,, VIC = VDD /2, No load 25C 80 Full range 80 IDD Supplyy current (four amplifiers) VO = 0 0, No load 25C Full range 88 75 88 dB 75 95 80 95 dB 80 160 250 300 160 250 300 A Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 28 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VO = 2 V V, CL = 100 pF RL = 100 k k, TA TLC2254Q TLC2254M MIN TYP 25C 0.07 0.12 Full range 0.05 TLC2254AQ TLC2254AM MAX MIN TYP 0.07 0.12 UNIT MAX SR Slew rate at unity gain Vn Equivalent q input noise voltage f = 10 Hz 25C 38 38 f = 1 kHz 25C 19 19 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.8 0.8 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.1 1.1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 2.3 V, RL = 50 k, k f = 20 kHz AV = 1 0.2% 0.2% THD + N 1% 1% Gain-bandwidth product f =10 kHz, CL = 100 pF RL = 50 k, 25C 0.21 0.21 MHz BOM Maximum output-swing bandwidth VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF 25C 14 14 kHz m Phase margin at unity gain RL = 50 k, CL = 100 pF 25C 63 63 Gain margin 25C Full range is - 40C to 125C for Q suffix, - 55C to 125C for M suffix. 15 15 nV/Hz V fA /Hz 25C AV = 10 POST OFFICE BOX 655303 V/s 0.05 * DALLAS, TEXAS 75265 dB 29 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Distribution vs Common-mode input voltage 2-5 6, 7 VIO IIB/IIO Input offset voltage temperature coefficient Distribution 8 - 11 Input bias and input offset currents vs Free-air temperature 12 VI Input voltage range vs Supplyy voltage g vs Free-air temperature 13 14 VOH VOL High-level output voltage vs High-level output current 15 Low-level output voltage vs Low-level output current 16, 17 VOM + VOM - Maximum positive peak output voltage vs Output current 18 Maximum negative peak output voltage vs Output current 19 VO(PP) Maximum peak-to-peak output voltage vs Frequency 20 IOS Short circuit output current Short-circuit vs Supply y voltage g vs Free-air temperature 21 22 VO Output voltage vs Differential input voltage Differential gain vs Load resistance AVD Large signal differential voltage amplification Large-signal vs Frequency q y vs Free-air temperature 26,, 27 28, 29 zo Output impedance vs Frequency 30, 31 CMRR Common mode rejection ratio Common-mode vs Frequency q y vs Free-air temperature 32 33 kSVR Supply voltage rejection ratio Supply-voltage vs Frequency q y vs Free-air temperature 34,, 35 36 IDD Supply current vs Supplyy voltage g vs Free-air temperature 37 38 SR Slew rate vs Load capacitance vs Free-air temperature 39 40 VO VO Inverting large-signal pulse response 41, 42 Voltage-follower large-signal pulse response 43, 44 VO VO Inverting small-signal pulse response 45, 46 Voltage-follower small-signal pulse response 47, 48 Vn Equivalent input noise voltage vs Frequency Noise voltage (referred to input) Over a 10-second period 51 Integrated noise voltage vs Frequency 52 Total harmonic distortion plus noise vs Frequency 53 Gain bandwidth product Gain-bandwidth vs Free-air temperature vs Supply voltage 54 55 m Phase margin vs Frequency q y vs Load capacitance 26,, 27 56 Am Gain margin vs Load capacitance 57 B1 Unity-gain bandwidth vs Load capacitance 58 Overestimation of phase margin vs Load capacitance 59 THD + N 30 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23, 24 25 49, 50 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLC2252 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLC2252 INPUT OFFSET VOLTAGE 35 30 Percentage of Amplifiers - % Percentage of Amplifiers - % 30 35 682 Amplifiers From 1 Wafer Lots VDD = 2.5 V P Package TA = 25C 25 20 15 10 5 682 Amplifiers From 1 Wafer Lots VDD = 5 V P Package TA = 25C 25 20 15 10 5 0 - 1.6 - 0.8 0 0.8 0 - 1.6 1.6 - 0.8 VIO - Input Offset Voltage - mV Figure 2 0.8 1.6 Figure 3 DISTRIBUTION OF TLC2254 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLC2254 INPUT OFFSET VOLTAGE 20 25 Percentage of Amplifiers - % 1020 Amplifiers From 1 Wafer Lot VDD = 2.5 V TA = 25C Percentage of Amplifiers - % 0 VIO - Input Offset Voltage - mV 15 10 5 20 1020 Amplifiers From 1 Wafer Lot VDD = 5 V TA = 25C 15 10 5 0 - 1.6 - 0.8 0 0.8 VIO - Input Offset Voltage - mV 1.6 0 - 1.6 Figure 4 0 0.8 - 0.8 VIO - Input Offset Voltage - mV 1.6 Figure 5 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 31 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE 1 VDD = 5 V RS = 50 TA = 25C 0.8 0.6 VVIO IO - Input Offset Voltage - mV VVIO IO - Input Offset Voltage - mV 1 VDD = 5 V RS = 50 TA = 25C 0.8 0.4 0.2 0 - 0.2 AAA AAA 0.6 0.4 0.2 0 - 0.2 AA AA AA - 0.4 - 0.6 - 0.8 - 0.4 - 0.6 - 0.8 -1 -1 0 1 2 3 4 5 VIC - Common-Mode Input Voltage - V -1 -6 -5 -4 -3 -2 -1 0 1 2 3 4 VIC - Common-Mode Input Voltage - V Figure 6 Figure 7 DISTRIBUTION OF TLC2252 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT DISTRIBUTION OF TLC2252 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 25 62 Amplifiers From 1 Wafer Lot VDD = 2.5 V 62 Amplifiers From 1 Wafer Lot VDD = 5 V P Package TA = 25C to 125C P Package TA = 25C to 125C Percentage of Amplifiers - % Precentage of Amplifiers - % 25 20 15 10 20 15 10 5 5 0 0 -1 0 1 VIO - Temperature Coefficient - V / C 2 -1 0 1 VIO - Temperature Coefficient - V / C Figure 9 Figure 8 For curves where VDD = 5 V, all loads are referenced to 2.5 V. 32 5 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 2 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLC2254 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 20 25 62 Amplifiers From 1 Wafer Lot VDD = 2.5 V P Package TA = 25C to 125C Percentage of Amplifiers - % Percentage of Amplifiers - % 25 15 10 5 0 -2 DISTRIBUTION OF TLC2254 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT -1 0 1 VIO - Temperature Coefficient of Input Offset Voltage - V / C 62 Amplifiers From 1 Wafer Lot VDD = 5 V P Package TA = 25C to 125C 20 15 10 5 0 -2 2 -1 AA AA 1 2 Figure 11 INPUT VOLTAGE RANGE vs SUPPLY VOLTAGE INPUT BIAS AND INPUT OFFSET CURRENTS vs FREE-AIR TEMPERATURE 10 35 VDD = 2.5 V VIC = 0 VO = 0 RS = 50 RS = 50 TA = 25C 8 25 IIB 20 15 IIO 10 5 V VII - Input Voltage Range - V IIO - Input Bias and Input Offset Currents - pA IIIB IB and IIO Figure 10 30 0 VIO - Temperature Coefficient of Input Offset Voltage - V / C 6 4 2 0 | VIO | 5 mV -2 -4 -6 -8 - 10 0 25 45 65 85 105 TA - Free-Air Temperature - C 125 2 Figure 12 3 6 7 4 5 | VDD | - Supply Voltage - V 8 Figure 13 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 33 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT INPUT VOLTAGE RANGE vs FREE-AIR TEMPERATURE 5 5 VDD = 5 V V VOH OH - High-Level Output Voltage - V VDD = 5 V V VII - Input Voltage Range - V 4 AA AA 3 2 1 0 -1 - 75 - 55 - 35 - 15 5 25 45 65 85 105 125 TA - Free-Air Temperature - C TA = - 55C 4 TA = - 40C 3 TA = 25C 2 AA AA AA TA = 125C 1 0 0 200 400 600 | IOH| - High-Level Output Current - A Figure 14 Figure 15 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 1.4 1.2 VDD = 5 V TA = 25C 1 V VOL OL - Low-Level Output Voltage - V VOL VOL - Low-Level Output Voltage - V 800 VIC = 1.25 V VIC = 0 0.8 0.6 VIC = 2.5 V AAA AAA AAA 1.2 TA = 125C 1 0.8 TA = 25C 0.6 AA AA AA 0.4 0.2 0 0 1 2 3 4 5 IOL - Low-Level Output Current - mA VDD = 5 V VIC = 2.5 V TA = - 40C TA = - 55C 0.4 0.2 0 0 1 2 3 4 5 IOL - Low-Level Output Current - mA Figure 16 Figure 17 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. 34 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 6 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE vs OUTPUT CURRENT 5 4 3 TA = 25C 2 TA = 125C AA AA AA TA = - 40C TA = - 55C 1 VDD = 5 V 0 0 600 200 400 IO - Output Current - A 800 VOM - VOM - - Maximum Negative Peak Output Voltage - V VVOM OM ++ - Maximum Positive Peak Output Voltage - V MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE vs OUTPUT CURRENT - 3.8 VDD = 5 V VIC = 0 -4 TA = 125C - 4.2 TA = 25C TA = - 40C - 4.4 - 4.6 TA = - 55C AA AA AA - 4.8 -5 0 1 2 3 4 IO - Output Current - mA Figure 18 AA AA AA RL = 50 k TA = 25C VDD = 5 V 8 7 6 VDD = 5 V 4 3 2 1 0 10 2 10 3 10 4 10 5 10 I OS - Short-Circuit Output Current - mA IOS VO(PP) VO(PP) - Maximum Peak-to-Peak Output Voltage - V SHORT-CIRCUIT OUTPUT CURRENT vs SUPPLY VOLTAGE 10 5 6 Figure 19 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY 9 5 9 8 VID = - 100 mV 7 VO = 0 TA = 25C VIC = 0 6 5 4 3 2 1 0 -1 VID = 100 mV 2 f - Frequency - Hz 3 4 5 6 7 8 | VDD | - Supply Voltage - V Figure 20 Figure 21 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 35 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 5 VDD = 5 V RL = 50 k VIC = 2.5 V TA = 25C VO = 0 VDD = 5 V 10 9 8 4 VID = - 100 mV VO - Output Voltage - V IIOS OS - Short-Circuit Output Current - mA 11 7 6 5 4 3 3 2 2 1 1 VID = 100 mV 0 -1 - 75 - 50 - 25 0 25 50 75 100 0 0 250 500 750 1000 - 1000 - 750 - 500 - 250 VID - Differential Input Voltage - V 125 TA - Free-Air Temperature - C Figure 23 Figure 22 DIFFERENTIAL GAIN vs LOAD RESISTANCE OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE VO - Output Voltage - V 3 104 VDD = 5 V VIC = 0 RL = 50 k TA = 25C VO (PP) = 2 V TA = 25C Differential Gain - V/ mV 5 1 -1 103 VDD = 5 V VDD = 5 V 102 -3 -5 0 250 500 750 1000 - 1000 - 750 - 500 - 250 VID - Differential Input Voltage - V 10 1 101 102 RL - Load Resistance - k Figure 25 Figure 24 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. 36 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 103 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY AA AA AA 60 180 VDD = 5 V RL = 50 k CL= 100 pF TA = 25C 135 40 90 Phase Margin 20 45 Gain 0 0 - 20 om m - Phase Margin AVD AVD - Large-Signal Differential Voltage Amplification - dB 80 - 45 - 40 10 3 10 4 10 5 10 6 - 90 10 7 f - Frequency - Hz Figure 26 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY AA AA AA 60 180 VDD = 10 V RL= 50 k CL= 100 pF TA = 25C 135 40 Phase Margin 20 45 Gain 0 0 - 20 - 40 10 3 90 om m - Phase Margin AVD AVD - Large-Signal Differential Voltage Amplification - dB 80 - 45 10 4 10 5 10 6 - 90 10 7 f - Frequency - Hz Figure 27 For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 37 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE A A 10 4 VDD = 5 V VIC = 2.5 V VO = 1 V to 4 V AVD AVD - Large-Signal Differential Voltage Amplification - V/mV AVD AVD - Large-Signal Differential Voltage Amplification - V/mV 10 4 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE RL = 1 M 10 3 RL = 50 k 10 2 101 - 75 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C VDD = 5 V VIC = 0 VO = 4 V RL = 1 M 10 3 RL = 50 k 10 2 AA AA 101 - 75 125 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 28 Figure 29 OUTPUT IMPEDANCE vs FREQUENCY OUTPUT IMPEDANCE vs FREQUENCY 1000 1000 VDD = 5 V TA = 25C z o - Output Impedance - 0 zo VDD = 5 V TA = 25C z o - Output Impedance - 0 zo 125 100 AV = 100 10 AV = 10 1 AV = 1 100 AV = 100 10 AV = 10 1 AV = 1 0.1 10 2 10 3 10 4 10 5 f - Frequency - Hz 10 6 0.1 10 2 10 3 10 4 10 5 f - Frequency - Hz Figure 31 Figure 30 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. 38 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10 6 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE COMMON-MODE REJECTION RATIO vs FREQUENCY 94 CMRR - Common-Mode Rejection Ratio - dB CMRR - Common-Mode Rejection Ratio - dB 100 VDD = 5 V 80 VDD = 5 V 60 40 20 0 101 10 2 10 3 10 4 10 5 VDD = 5 V 92 90 86 84 82 80 - 75 16 6 VDD = 5 V 88 - 50 f - Frequency - Hz - 25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 32 Figure 33 SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY 100 kSVR + VDD = 5 V TA = 25C KSVR k SVR - Supply-Voltage Rejection Ratio - dB KSVR k SVR - Supply-Voltage Rejection Ratio - dB 100 80 60 kSVR - 40 20 AA AA AA 0 - 20 101 125 10 2 10 3 10 4 f - Frequency - Hz 10 5 10 6 VDD = 5 V TA = 25C kSVR + 80 60 kSVR - 40 20 AAA AAA AAA 0 - 20 101 Figure 34 10 2 10 3 10 4 f - Frequency - Hz 10 5 10 6 Figure 35 For curves where VDD = 5 V, all loads are referenced to 2.5 V. Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 39 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS SUPPLY-VOLTAGE REJECTION RATIO vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE 240 VDD = 2.2 V to 8 V VO = 0 VO = 0 No Load 200 105 IDD A I DD - Supply Current - uA k KSVR SVR - Supply-Voltage Rejection Ratio - dB 110 100 AA AA AA AA AA AA 95 90 - 75 - 50 - 25 0 25 50 75 100 TA = - 55C 160 TA = 25C 120 TA = 125C TA = - 40C 80 40 0 125 0 1 TA - Free-Air Temperature - C 6 2 3 4 5 | VDD | - Supply Voltage - V Figure 36 SLEW RATE vs LOAD CAPACITANCE 0.2 240 0.18 VDD = 5 V VO = 0 160 VDD = 5 V VO = 2.5 V 120 VDD = 5 V AV = - 1 TA = 25C 0.16 SR - Slew Rate - V/ v/us s 200 A IDD I DD - Supply Current - uA 8 Figure 37 SUPPLY CURRENT vs FREE-AIR TEMPERATURE AA AA 7 80 0.14 SR - 0.12 0.1 SR + 0.08 0.06 0.04 40 0.02 0 - 75 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C 125 0 101 Figure 38 10 2 10 3 CL - Load Capacitance - pF Figure 39 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. 40 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10 4 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS SLEW RATE vs FREE-AIR TEMPERATURE INVERTING LARGE-SIGNAL PULSE RESPONSE 0.2 5 SR - Slew Rate - v/uss V/ 0.16 VO VO - Output Voltage - V VDD = 5 V RL = 50 k CL = 100 pF AV = 1 SR - 0.12 SR + 0.08 VDD = 5 V RL = 50 k CL = 100 pF 4 A = -1 V TA = 25C 3 2 1 0.04 0 - 75 0 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C 0 125 10 20 VO VO - Output Voltage - V 2 60 70 80 90 100 VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 5 VO VO - Output Voltage - V VDD = 5 V RL = 50 k CL = 100 pF AV = - 1 TA = 25C 3 50 Figure 41 INVERTING LARGE-SIGNAL PULSE RESPONSE 4 40 t - Time - s Figure 40 5 30 1 0 -1 -2 VDD = 5 V RL = 50 k CL = 100 pF 4 A =1 V TA = 25C 3 2 1 -3 -4 0 -5 0 10 20 30 40 50 60 t - Time - s 70 80 90 100 0 10 Figure 42 20 30 40 50 60 70 t - Time - s 80 90 100 Figure 43 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 41 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS INVERTING SMALL-SIGNAL PULSE RESPONSE VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 5 3 2 VDD = 5 V RL = 50 k CL = 100 pF AV = - 1 TA = 25C 2.6 VO VO - Output Voltage - V 4 VO VO - Output Voltage - V 2.65 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25C 1 0 -1 -2 -3 2.55 2.5 2.45 -4 -5 2.4 0 10 20 30 40 50 60 t - Time - s 70 80 0 90 100 10 INVERTING SMALL-SIGNAL PULSE RESPONSE 0 - 0.05 2.65 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25C 2.6 VO VO - Output Voltage - V VO VO - Output Voltage - mV 50 VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE VDD = 5 V RL = 50 k CL = 100 pF AV = - 1 TA = 25C 0.05 40 Figure 45 Figure 44 0.1 20 30 t - Time - s 2.55 2.5 2.45 - 0.1 0 2.4 10 20 30 40 50 0 t - Time - s Figure 46 20 30 t - Time - s Figure 47 For curves where VDD = 5 V, all loads are referenced to 2.5 V. 42 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 40 50 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE 60 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25C 0.05 V n - Equivalent Input Noise Voltage - nV/ VN nv//HzHz VO VO - Output Voltage - V 0.1 0 - 0.05 - 0.1 0 10 20 30 t - Time - s 40 50 VDD = 5 V RS = 20 TA = 25C 50 40 30 20 10 0 101 10 2 10 3 f - Frequency - Hz Figure 49 Figure 48 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY EQUIVALENT INPUT NOISE VOLTAGE OVER A 10-SECOND PERIOD 1000 VDD = 5 V RS = 20 TA = 25C VDD = 5 V f = 0.1 Hz to 10 Hz TA = 25C 750 500 Noise Voltage - nV V n - Equivalent Input Noise Voltage - nv//Hz VN nV/ Hz 60 50 10 4 40 30 20 250 0 - 250 - 500 10 - 750 0 101 10 2 10 3 f - Frequency - Hz 10 4 - 1000 0 Figure 50 2 4 6 t - Time - s 8 10 Figure 51 For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 43 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY THD + N - Total Harmonic Distortion Plus Noise - % INTEGRATED NOISE VOLTAGE vs FREQUENCY Integrated Noise Voltage - V 100 Calculated Using Ideal Pass-Band Filter Low Frequency = 1 Hz TA = 25C 10 1 0.1 1 101 10 2 10 3 f - Frequency - Hz 10 4 10 5 1 AV = 100 0.1 AV = 10 0.01 AV = 1 VDD = 5 V RL = 50 k TA = 25C 0.001 101 10 2 10 5 Figure 53 GAIN-BANDWIDTH PRODUCT vs FREE-AIR TEMPERATURE GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 280 250 TA = 25C VDD = 5 V f = 10 kHz RL = 50 k CL = 100 pF 240 Gain-Bandwidth Product - kHz Gain-Bandwidth Product - kHz 10 4 f - Frequency - Hz Figure 52 200 160 120 80 - 75 10 3 230 210 190 170 150 - 50 - 25 0 25 50 75 100 125 0 1 TA - Free-Air Temperature - C 2 3 4 5 6 7 | VDD | - Supply Voltage - V Figure 54 Figure 55 For curves where VDD = 5 V, all loads are referenced to 2.5 V. Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 44 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 8 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 TYPICAL CHARACTERISTICS PHASE MARGIN vs LOAD CAPACITANCE 75 GAIN MARGIN vs LOAD CAPACITANCE 20 Rnull = 200 TA = 25C Rnull = 500 Rnull = 500 60 Gain Margin - dB om m - Phase Margin 15 45 Rnull = 100 Rnull = 50 30 Rnull = 10 50 k VI Rnull = 50 5 VDD + Rnull - + Rnull = 0 Rnull = 0 CL TA = 25C VDD - 0 101 Rnull = 100 10 Rnull = 10 50 k 15 Rnull = 200 10 4 10 2 10 3 CL - Load Capacitance - pF 0 101 10 5 10 2 10 3 Figure 57 OVERESTIMATION OF PHASE MARGIN vs LOAD CAPACITANCE UNITY-GAIN BANDWIDTH vs LOAD CAPACITANCE 25 200 TA = 25C TA = 25C Rnull = 500 Overestimation of Phase Margin 175 B1 - Unity-Gain Bandwidth - kHz 10 5 CL - Load Capacitance - pF Figure 56 AA AA 10 4 150 125 100 75 50 20 15 Rnull = 100 10 Rnull = 200 Rnull = 50 Rnull = 10 5 25 0 101 10 2 10 3 10 4 10 5 0 101 CL - Load Capacitance - pF Figure 58 10 2 10 3 10 4 CL - Load Capacitance - pF 10 5 Figure 59 See application information POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 45 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 APPLICATION INFORMATION driving large capacitive loads The TLC225x is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 56 and Figure 57 illustrate its ability to drive loads up to 1000 pF while maintaining good gain and phase margins (Rnull = 0). A smaller series resistor (Rnull) at the output of the device (see Figure 60) improves the gain and phase margins when driving large capacitive loads. Figure 56 and Figure 57 show the effects of adding series resistances of 10 , 50 , 100 , 200 , and 500 . The addition of this series resistor has two effects: the first is that it adds a zero to the transfer function and the second is that it reduces the frequency of the pole associated with the output load in the transfer function. The zero introduced to the transfer function is equal to the series resistance times the load capacitance. To calculate the improvement in phase margin, equation 1 can be used. m1 + tan-1 2 x x UGBW x R x C null (1) L Where : + Improvement in phase margin UGBW + Unity-gain bandwidth frequency R null + Output series resistance C L + Load capacitance m1 The unity-gain bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 58). To use equation 1, UGBW must be approximated from Figure 58. Using equation 1 alone overestimates the improvement in phase margin, as illustrated in Figure 59. The overestimation is caused by the decrease in the frequency of the pole associated with the load, thus providing additional phase shift and reducing the overall improvement in phase margin. Using Figure 60, with equation 1 enables the designer to choose the appropriate output series resistance to optimize the design of circuits driving large capacitance loads. 50 k VDD + 50 k VI Rnull - + CL VDD - / GND Figure 60. Series-Resistance Circuit 46 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D - FEBRUARY 1997 - REVISED MARCH 2001 APPLICATION INFORMATION macromodel information Macromodel information provided was derived using MicroSim Parts, the model generation software used with MicroSim PSpice . The Boyle macromodel (see Note 5) and subcircuit in Figure 61 are generated using the TLC225x typical electrical and operating characteristics at TA = 25C. Using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): D D D D D D D D D D D D Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, "Macromodeling of Integrated Circuit Operational Amplifiers", IEEE Journal of Solid-State Circuits, SC-9, 353 (1974). 99 3 VCC + 9 RSS 92 FB 10 J1 DP VC J2 IN + 11 RD1 VAD DC 12 C1 R2 - 53 HLIM - + C2 6 - - - + VLN + GCM GA VLIM 8 - RD2 54 4 91 + VLP 7 60 + - + DLP 90 RO2 VB IN - VCC - - + ISS RP 2 1 DLN EGND + - RO1 DE 5 + VE OUT .SUBCKT TLC225x 1 2 3 4 5 C1 11 12 6.369E-12 C2 6 7 25.00E-12 DC 5 53 DX DE 54 5 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY (5) VB VC VE VLP + VLN 0 57.62E6 -60E6 60E6 60E6 -60E6 GA 6 0 11 12 26.86E-6 GCM 0 6 10 99 2.686E-9 ISS 3 10 DC 3.1E-6 HLIM 90 0 VLIM 1K J1 11 2 10 JX J2 12 1 10 JX R2 6 9 100.0E3 RD1 60 11 37.23E3 RD2 60 12 37.23E3 R01 8 5 84 R02 7 99 84 RP 3 4 71.43E3 RSS 10 99 64.52E6 VAD 60 4 -.5 VB 9 0 DC 0 VC 3 53 DC .605 VE 54 4 DC .605 VLIM 7 8 DC 0 VLP 91 0 DC -.235 VLN 0 92 DC 7.5 .MODEL DX D (IS=800.0E-18) .MODEL JX PJF (IS=500.0E-15 BETA=139E-6 + VTO=-.05) .ENDS Figure 61. Boyle Macromodel and Subcircuit PSpice and Parts are trademarks of MicroSim Corporation. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 47 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) 5962-9564001NXD ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 5962-9564001NXDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 5962-9564001Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-9564001QHA ACTIVE CFP U 10 1 TBD Call TI Call TI 5962-9564001QPA ACTIVE CDIP JG 8 1 TBD Call TI Call TI 5962-9564002NYDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 5962-9564002Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-9564002QCA ACTIVE CDIP J 14 1 TBD Call TI Call TI 5962-9564002QDA ACTIVE CFP W 14 1 TBD Call TI Call TI 5962-9564003NXD ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 5962-9564003NXDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 5962-9564003Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-9564003QHA ACTIVE CFP U 10 1 TBD Call TI Call TI 5962-9564003QPA ACTIVE CDIP JG 8 1 TBD Call TI Call TI 5962-9564004NYDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 5962-9564004Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-9564004QCA ACTIVE CDIP J 14 1 TBD Call TI Call TI 5962-9564004QDA ACTIVE CFP W 14 1 TBD Call TI Call TI TLC2252AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AIDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) TLC2252AIP ACTIVE TLC2252AIPE4 ACTIVE TLC2252AIPW ACTIVE TLC2252AIPWG4 ACTIVE TLC2252AIPWLE TLC2252AIPWR Package Type Package Drawing PDIP Pins P 8 PDIP P TSSOP PW TSSOP OBSOLETE ACTIVE TLC2252AIPWRG4 Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TSSOP PW 8 TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AMFKB ACTIVE LCCC FK 20 1 TBD TLC2252AMJGB ACTIVE CDIP JG 8 1 TBD TLC2252AMUB ACTIVE CFP U 10 1 TBD TLC2252AQD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AQDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AQDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252AQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252CD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252CDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252CDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2252CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2252CPW ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) Addendum-Page 2 Call TI Samples (Requires Login) 50 TBD (3) Call TI POST-PLATE N / A for Pkg Type A42 N / A for Pkg Type A42 N / A for Pkg Type CU NIPDAU Level-1-260C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty 150 Eco Plan (2) Green (RoHS & no Sb/Br) Lead/ Ball Finish MSL Peak Temp ACTIVE TSSOP PW 8 CU NIPDAU Level-1-260C-UNLIM TLC2252CPWLE OBSOLETE TSSOP PW 8 TLC2252CPWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252CPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2252IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Call TI Call TI TLC2252IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2252IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2252MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type TLC2252MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type TLC2252MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type 75 Green (RoHS & no Sb/Br) TLC2252QD ACTIVE SOIC D 8 TLC2252QDG4 ACTIVE SOIC D 8 TBD TBD Call TI Call TI CU NIPDAU Level-1-260C-UNLIM TLC2252QDR ACTIVE SOIC D 8 TLC2252QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIN ACTIVE PDIP N 14 25 Pb-Free (RoHS) Addendum-Page 3 Call TI Samples (Requires Login) TLC2252CPWG4 TBD (3) Call TI CU NIPDAU N / A for Pkg Type PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2254AIPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIPWLE OBSOLETE TSSOP PW 14 TLC2254AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AIPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AMFKB ACTIVE LCCC FK 20 1 TBD TLC2254AMJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type TLC2254AMWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type TLC2254AQD ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AQDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AQDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254AQDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254CD ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM TLC2254CDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM TLC2254CDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254CDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Call TI Call TI POST-PLATE N / A for Pkg Type TLC2254CN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2254CNE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2254CPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254CPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 4 Samples (Requires Login) TLC2254AINE4 TBD (3) PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) TBD Lead/ Ball Finish Call TI MSL Peak Temp OBSOLETE TSSOP PW 14 TLC2254CPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254CPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254ID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254IDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254IDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2254IDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Call TI TLC2254IN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2254INE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC2254MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type TLC2254MJB ACTIVE CDIP J 14 1 TBD TLC2254MWB ACTIVE CFP W 14 1 TLC2254QD ACTIVE SOIC D 14 TLC2254QDG4 ACTIVE SOIC D 14 TLC2254QDR ACTIVE SOIC D 14 TLC2254QDRG4 ACTIVE SOIC D 14 A42 N / A for Pkg Type TBD A42 N / A for Pkg Type TBD Call TI Green (RoHS & no Sb/Br) TBD 2500 Green (RoHS & no Sb/Br) Samples (Requires Login) TLC2254CPWLE 50 (3) Call TI CU NIPDAU Level-1-260C-UNLIM Call TI Call TI CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 5 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TLC2252, TLC2252A, TLC2252AM, TLC2252M, TLC2254, TLC2254A, TLC2254AM, TLC2254M : * Catalog: TLC2252A, TLC2252, TLC2254A, TLC2254 * Automotive: TLC2252-Q1, TLC2252A-Q1, TLC2252A-Q1, TLC2252-Q1, TLC2254-Q1, TLC2254A-Q1, TLC2254A-Q1, TLC2254-Q1 * Enhanced Product: TLC2252-EP, TLC2252A-EP, TLC2252A-EP, TLC2252-EP, TLC2254-EP, TLC2254A-EP, TLC2254A-EP, TLC2254-EP * Military: TLC2252M, TLC2252AM, TLC2254M, TLC2254AM NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications * Military - QML certified for Military and Defense Applications Addendum-Page 6 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 5962-9564001NXDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 5962-9564002NYDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 5962-9564003NXDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 5962-9564004NYDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLC2252AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC2252AIPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 TLC2252CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC2252CPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 TLC2252IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC2254AIDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLC2254AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TLC2254AQDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLC2254CDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLC2254CPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TLC2254IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 5962-9564001NXDR SOIC 5962-9564002NYDR SOIC D 8 2500 367.0 367.0 35.0 D 14 2500 367.0 367.0 38.0 5962-9564003NXDR SOIC 5962-9564004NYDR SOIC D 8 2500 367.0 367.0 35.0 D 14 2500 367.0 367.0 TLC2252AIDR 38.0 SOIC D 8 2500 340.5 338.1 20.6 TLC2252AIPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLC2252CDR SOIC D 8 2500 340.5 338.1 20.6 TLC2252CPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLC2252IDR SOIC D 8 2500 340.5 338.1 20.6 TLC2254AIDR SOIC D 14 2500 367.0 367.0 38.0 TLC2254AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 TLC2254AQDR SOIC D 14 2500 367.0 367.0 38.0 TLC2254CDR SOIC D 14 2500 367.0 367.0 38.0 TLC2254CPWR TSSOP PW 14 2000 367.0 367.0 35.0 TLC2254IDR SOIC D 14 2500 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MCER001A - JANUARY 1995 - REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0-15 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated