Switching Power Supply S82J
1
Switching Power Supply
S82J
DIN-Rail Mounting Industrial Power
Supplies with Capacity Up to 600 W
DModels range from 10 to 600 W.
DUL 508 approval.
DClass 2 approval available for models below 100 W.
DUniversal input or selectable input.
DWide range of output voltages: 5 V,
12 V, 15 V, or 24 V.
DUL, CSA, VDE, and CE Approvals.
D3-Year warranty.
Ordering Information
JOPEN-FRAME TYPE POWER SUPPLIES
Stock Note: Shaded models are normally stocked.
Rated input voltage Power
ratings
Output Part number
Rated input voltage
Power
ratings Voltage Current Front-mounting
bracket DIN-rail mounting
bracket
5 V 2 A S82J-01005A S82J-01005AD
10 W
12 V 1 A S82J-01012A S82J-01012AD
10 W
15 V 0.7 A S82J-01015A S82J-01015AD
24 V 0.5 A S82J-01024A S82J-01024AD
5 V 5 A S82J-02505A S82J-02505AD
100 to 240 VAC
25 W
12 V 2.1 A S82J-02512A S82J-02512AD
100 to 240 VAC
25 W
15 V 1.7 A S82J-02515A S82J-02515AD
24 V 1.1 A S82J-02524A S82J-02524AD
5 V 10 A S82J-05005A S82J-05005AD
50 W 12 V 4.2 A S82J-05012A S82J-05012AD
50 W
24 V 2.1 A S82J-05024A S82J-05024AD
120 or 240 VAC
(automatically selected)
5 V 20 A S82J-10005A S82J-10005AD
120 or 240 VAC
(automatically selected)
100 W
12 V 8.5 A S82J-10012A S82J-10012AD
100 W
15 V 7 A S82J-10015A S82J-10015AD
100 to 240 VAC 24 V 4.5 A S82J-10024A S82J-10024AD
120 or 240 VAC
(automatically selected) 150 W 24 V 6.5 A S82J-15024A S82J-15024AD
2
Switching Power Supply S82J
JCOVERED-FRAME TYPE POWER SUPPLIES
Stock Note: Shaded models are normally stocked.
Rated input voltage Power
ratings
Output Part number
Rated input voltage
Power
ratings Voltage Current Front-mounting
bracket DIN-rail mounting
bracket
5 V 2 A S82J-01005D S82J-01005DD
10 W
12 V 1 A S82J-01012D S82J-01012DD
10 W
15 V 0.7 A S82J-01015D S82J-01015DD
24 V 0.5 A S82J-01024D S82J-01024DD
5 V 5 A S82J-02505D S82J-02505DD
100 to 240 VAC
25 W
12 V 2.1 A S82J-02512D S82J-02512DD
100 to 240 VAC
25 W
15 V 1.7 A S82J-02515D S82J-02515DD
24 V 1.1 A S82J-02524D S82J-02524DD
5 V 10 A S82J-05005D S82J-05005DD
50 W 12 V 4.2 A S82J-05012D S82J-05012DD
50 W
24 V 2.1 A S82J-05024D S82J-05024DD
120 or 240 VAC
(automatically selected)
5 V 20 A S82J-10005D S82J-10005DD
120 or 240 VAC
(automatically selected)
100 W
12 V 8.5 A S82J-10012D S82J-10012DD
100 W
15 V 7 A S82J-10015D S82J-10015DD
100 to 240 VAC 24 V 4.5 A S82J-10024D S82J-10024DD
120 or 240 VAC
(automatically selected) 150 W 24 V 6.5 A S82J-15024D S82J-15024DD
JENCLOSED-FRAME TYPE POWER SUPPLIES
Stock Note: Shaded models are normally stocked.
Input voltage Power rating Output Part number
Input voltage
Power rating
Voltage Current
Part number
120 or 230 VAC (selectable) 300 W 24 V 14.0 A S82J-30024
120 or 230 VAC (selectable)
600 W 24 V 27.0 A S82J-60024
Note: 1. A mounting bracket is included with each power supply.
2. To order without a mounting bracket (normally included with the 300 W or 600 W), add an “N” at the end of the part number.
3. For other accessories, refer to the Accessories section that follows.
3Switching Power Supply S82J
JACCESSORIES
Stock Note: Shaded models are normally stocked.
Description Applicable power supplies Part number
Front-mounting bracket for 100-W, 24-V models S82Y-J10F
DIN-rail 1 m (3.28 ft) length for 10- to 150-W models PFP-100N/PFP-100N2
DIN-rail
0.5 m (1.64 ft) length for 10- to 150-W models PFP-50N
Cover for 10-W models S82Y-J01K
Cover
for 25-W models S82Y-J02K
for 50-W models S82Y-J05K
for 100-W, 24-V models S82Y-J10K
Fan for 600-W models S82Y-JFAN
Ferrite ring core
(a set of 3 pieces in package) for 300-W and 600-W models S82Y-JC-T
Noise filter for 300-W models for 200 to 230 VAC input S82Y-JF3-N
Noise filter
for 600-W models for 200 to 230 VAC input S82Y-JF6-N
JMODEL NUMBER LEGEND
S82J -
1 3
2 4
3. Configuration
A: Open-frame type, front terminals
B: Covered-type, front terminals
None: Enclosed-type, front terminals
with mounting bracket
4. Mounting Bracket
None: Front-mounting Bracket Type
D: DIN-rail Mounting Bracket Type
2. Output voltage
05: 5 V
12: 12 V
15: 15 V
24: 24 V
1. Power ratings
010: 10 W
025: 25 W
050: 50 W
100: 100 W
150: 150 W
300: 300 W
600: 600 W
4
Switching Power Supply S82J
Specifications
Item 100 to 240 VAC input 120 or 240 VAC
(selected
automatically)
120 or 230 VAC
(selectable)
10 W 25 W 50 W 100 W
(24 V) 100 W
(5, 12,
15 V)
150 W 300 W 600 W
Efficiency (typical) 67% min. (77% min. for 50-W,
24-V models) 83% min. 75%
min. 82% min.
Input Voltage 100 to 240 VAC
(85 to 264 VAC)
110 to 170 VDC
(set the terminal (L)
to + side)
(See Note 1.)
100 to 240 VAC
(85 to 264 VAC) 120 (85 to 132) or
240 (170 to 264)
VAC (selected auto-
matically)
120 (85 to 132) or
230 (170 to 253) VAC
(selectable)
Frequency 50/60 Hz (47 to 450 Hz)
Current
(See Note
2.)
100 VAC
input 0.35 A
max. 0.8 A
max. 1.4 A
max. 2.5 A
max. 2.5 A
max. 3.5 A
max. 8 A max. 14 A max.
(See Note
2.) 200 VAC
input 0.3 A
max. 0.6 A
max. 0.8 A
max. 1.15 A
max. 1.4 A
max. 2.1 A
max. 4 A max. 7 A max.
Leakage
current (See
Note 2.)
100 VAC
input 0.5mA max.
current (See
Note 2.) 200 VAC
input 1mA max.
Inrush cur-
rent (25_C,
cold start)
100 VAC
input 25 A max. 30 A max.
cold start)
(See Note
2.) 200 VAC
input 50 A max. 60 A max.
Noise filter Yes
Output (See
Note 3.) Voltage adjustment
range 10% (adjustable with variable resistor (V.ADJ))
Note 3.)
Ripple (See Note 2.) 2% (p-p) max.
Input variation influence 0.4% max
Load variation influence 0.8% max. (with rated input, 10% to 100% load)
Temperature variation
influence 0.05%/_C max. (with rated input and output)
Startup time 500 ms max. (up to 90% of output voltage at rated input and out-
put) 300 ms max. (up to
90% of output voltage
at rated input and out-
put)
Hold time (See Note 2.) 20 ms min.
Additional
function Overload protection 105% to 160% of rated load current, in-
verted L drop/intermittent operation type,
automatic reset
105% min. of rated load current, inverted L drop
type, automatic reset (For the 600-W model, the
circuit will be shut OFF when the overload ex-
ceeds 5s. Protection-ON alarm indicator lit (See
Note 5.)
Overvoltage protection NO Yes (See
Note 4.) Yes (5-V
output
models
only)
(See
Note 4.)
No Yes, protection-ON
alarm indicator lit (See
Note 5.)
Overheat protection No Yes, protec-
tion ON
alarm indi-
cator lit (See
Note 5.)
(This table continues on the next page.)
5Switching Power Supply S82J
Specifications Table – continued from previous page
Item 100 to 240 VAC input 120 or 240 VAC
(selected
automatically)
120 or 230 VAC
(selectable)
10 W 25 W 50 W 100 W
(24V) 100 W
(5, 12,
15 V)
150 W 300 W 600 W
Additional
function Protection-ON alarm
indicator No Yes (color, red)
function
Parallel operation No Yes, 5 units max.
Series operation No Yes
Other Ambient
temperature Operat-
ing See the derating curve in the Engineering Data Section.
temperature
Storage -25_C to 65_C (-13_F to 149_F) with no condensation and icing
Ambient
humidity Operat-
ing 25% to 85%
humidity
Storage: 25% to 90%
Dielectric strength 3.0 k VAC, 50/60 Hz for 1 min (between all inputs and all outputs)
Dielectric strength
2.2 k VAC, 50/60 Hz for 1 min (between all inputs and GR terminal)
1.0 k VAC, 50/60 Hz for 1 min (between all outputs and GR terminal)
Insulation resistance 100 MW min. (between all outputs and all inputs/GR terminals at 500 VDC)
Vibration resistance 10 to 55 Hz, 0.375-mm double amplitude for 2 h each in X, Y, and Z directions
Shock resistance 300 m/s2, 3 times each in X, Y, and Z directions
Terminal screw
tightening 0.74 N m 1.08 N m
Output indicator Yes (green)
Electromagnetic interfer-
ence (See Note 2.) Conforms to FCC Class A
EMC Emission Enclosure: EN55011 class A
Emission AC Mains: EN55011 class A
Immunity ESD: EN61000-4-2: 4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference: ENV50140: 10 Vm (80 MHz to 1 GHz) (level 3)
Immunity Conducted Disturbance: ENV50141: 10 V (0.5 to 80 MHz) (level 3)
Immunity Burst EN61000-4-4 2 kV power-line (level 3)
2 kV output line (level 4)
EMC standards Conforms to EN50081-2 and EN50082-2 Conforms to
EN50081-2 and
EN50082-2 (See Note
6.) With noise filter,
confirms to EN50081-1
(See Note 6 and 7.)
Approved
standards UL UL508 (Listing), 1950, Class 2
(per UL1310) (See Note 8.) UL508 (Listing), 1012, 1950 UL508/1012
standards
CSA CSA C22.2 No. 14, No. 950,
Class 2 (See Note 8.) CSA C22.2 No. 14, No. 950 CSA EB1402C
VDE EN50178 (VDE0160) and EN60950
Terminal types (only terminal part): VDE0106/P100
Weight (See Note 9.) 250 g
max. 350 g
max. 400 g
max. 500 g
max. 1,000 g max 2,000 g
max. 2,500 g
max.
Mean time between
failures 135,000 hrs min. (MTBF is calculated according to the probability of accidental device fail-
ures, and indicates reliability of devices. It does not necessarily represent a life of the product.
Life expectancy 10 yrs. min. (Used at 40_C at the rated input with a 50% load, standard installation).
Note: 1. DC inputs are not included in safety standard approvals.
2. At 100% load for rated input voltage (100 VAC or 200 VAC)
3. The output specification is defined at the power supply output terminals.
4. For resetting, turn OFF the power supply, leave for more than one minute, and then turn ON the power supply.
5. For resetting, turn OFF the power supply, leave for more than 90 seconds min. (3 minutes for the 600-W models), and then turn
ON the power supply.
6. To ensure the Emission Enclosure rating ferrite ring cores (recommended model: S82Y-JC-T) should be used on all cabling.
7. To ensure the Emission AC Mains rating for EN50081-1 (only for 230 VAC input), a noise filter (recommended models:
S82Y-JF3-N for 300-W, S82Y-JF6-N for 600-W) should be used on the input lines.
8. Class 2 approval on 10-W (12, 15, 24 V), 25-W (12, 15, 24 V) and 50-W (24 V) models.
9. The weight indicated is the weight of the open-frame type. (Includes the covers for 300-W and 600-W models)
6
Switching Power Supply S82J
JDERATING CURVE
S82J 10/25/50/100/150 W
Note: 1. The derating curve shown is for standard installation. The derating curve depends on the mounting direction of the Power
Supply.
2. Provide a minimum clearance of 20 mm between the Power Supplies. Refer to the Mounting information in the Dimensions
section.
Open-frame type
Load (%)
Ambient temperature (°C)
Covered-type
Load (%)
Ambient temperature (°C)
Mounting Position for
Standard Installation
Natural air cooling
Forced-air cooling
(1 m3/min)
Natural air-cooling
55% 55°C
Forced-air cooling
(1 m3/min)
Parallel Operation Mounting Position for
Standard Installation
Load (%)
Ambient temperature (°C)
Forced-air cooling
(1 m3/min)
(Standard mounting)
Natural air cooling
(Standard mounting)
Forced-air cooling
(1 m3/min)
(Side mounting)
Single Operation
Load (%)
Ambient temperature (°C)
Natural air cooling
(Standard mounting)
Forced-air cooling
(1 m3/min)
(Side mounting)
Natural cooling
(Side mounting)
Forced-air cooling
(1 m3/min)
(Standard mounting)
20 mm min. 20 mm min.
20 mm min. 20 mm min.
Natural cooling
(Side mounting)
120 120
100 100
7Switching Power Supply S82J
600-W Model
Single Operation Parallel Operation
Load (%)
Ambient temperature (°C)
Load (%)
Ambient temperature (°C)
Mounting Position for
Standard Installation
20 mm min. 20 mm min.
20 mm min. 20 mm min.
120 120
100 100
Output voltage (V)
Output current (%)
Intermittent
operation
500 100
Rated voltage
JOVERLOAD PROTECTION
10- to 300-W Models
The Power Supply is provided with an overload protection func-
tion that protects the load and the power supply from possible
damage by overcurrent. When the output current rises above
105% to 160% of the rated output current, the protection func-
tion is triggered, decreasing the output voltage. When the out-
put current falls within the rated range, the overload protection
function is automatically cleared.
Output voltage (V)
Output current (%)
Rated voltage
100-W (5, 12, 15-V), 150-W,
300-W models
10-W to 100-W (24-V) Models
600-W Models
If an excessive current flows for 5 sec or more, the output will be
turned off and simultaneously protection-ON alarm indicator
will be lit. To reset the S82J, turn off the input voltage, leave the
S82J for at least three minutes, and then apply the input voltage
again.
Note: Do not continue using the S82J with the output termi-
nals short-circuited or the overcurrent condition contin-
ued, otherwise the internal elements of the S82J may
be damaged or broken.
Output voltage (V)
Output current (%)
Rated voltage
Output shut off after 5 s
8
Switching Power Supply S82J
Output voltage (V)
Overvoltage
protection
operating
Approx.
20%
10%
–10%
Rated output
voltage Variable range
Note: The output voltage can be varied by the V. ADJ
adjuster on the front panel. When it is set to a
value 10% higher than the rated value, the over-
voltage protection function may be effected.
JOVERVOLTAGE PROTECTION
100-W (5, 24 V) Output Models
These power supplies have an overvoltage protection
function that protects the load and the power supply from
possible damage by overvoltage. When the output voltage
rises above a set value (120% of the rated output voltage),
the protection function is triggered, shutting off the output
voltage. If this occurs, reset the power supply by turning it off
for 1 minute minimum and then turning it on again.
300- and 600-W Models
If a voltage that is 120% of the rated output voltage or above is
output, the output voltage will be turned of f and simultaneously
protection-ON alarm indicator will be lit. To reset the S82J, turn
off the input voltage, leave the S82J for at least three minutes if
it is a 600-W model or at least 90 seconds if it is a 300-W model,
and then apply the input voltage again.
JOVERHEAT PROTECTION FUNCTION
600-W Model Only
If the internal temperature of the S82J rises excessively as a
result of fan failure or any other reason, the overheat protection
circuit will be triggered to protect the internal elements of the
S82J and simultaneously a protection-ON alarm indicator will be
lit. To reset the S82J, turn off the input voltage, leave the S82J for
at least three minutes, and then apply the input voltage again.
Input OFF
Input ON
AC input voltage
AC input current
Output voltage
Inrush current on input application
Start up time
Hold time
(20 ms min.)
90% 96.5%
JINRUSH CURRENT, START UP TIME, HOLD TIME
9Switching Power Supply S82J
Installation
600-W Models
+V
+V
*V
*V
5
6
1AC (L)
AC (N) 2
4
3
GR
300-W Models
165 7
8
423
AC (L)
AC (N)GR
8
Side view
7
Side view
5
6
1
3
2
+V
–V
AC (L)
AC (N)
JS82J 10 W TO 150 W
GR
1. DC Output Terminals: Connect the load lines to
these terminals.
2. Input Terminals: Connect the input lines to these
terminals.
3. Ground Terminal (GR): Connect a ground line to
this terminal.
4. Input Voltage Selector Terminals: Short-circuit
the terminals if the input is 100 to 120 VAC and
open the terminals if the input is 200 to 230 VAC
•Only for 300-W and 600-W unit.
5. Output Indicator (DC ON): Lights while a Direct
Current (DC) output is ON.
6. Output Voltage Adjuster (V.ADJ): It is possible to
increase or decrease the output voltage by 10%.
7. Protection-ON Alarm Indicator: The red indicator
will be lit if the overvoltage (for a 300-/600-W
model) or overheat protection (for a 600-W model)
circuit is triggered. This indicator will also be lit
when overcurrent (for a 600-W model) is detected.
8. Parallel/Single Operation Selector: Set the selec-
tor to PARALLEL if the Units are in parallel opera-
tion.
–V –V +V +V
10
Switching Power Supply S82J
JBLOCK DIAGRAMS
Drive
control
circuit
+V
–V
DC Output
AC(L)
AC(N)
Fuse*
Noise filter
Inrush current
protection circuitRectifier
Rectifier
Detector
Photocoupler
Input
*Fuse capacity: 10 W, 1 A
25 W, 2 A
S82J-010jjjj (10 W)
S82J-025jjjj (25 W)
jjjj
S82J-10024jj (100 W)
Input
AC(L)
AC(N)
Fuse*
Noise filter
Control circuit
Overload
detection
circuit Photocoupler
Overload
detection
circuit
+V
–V
DC Output
Inrush current
protection
circuit
Rectifier Smoothing
circuit Rectifier and
smoothing
circuit
*Fuse capacity: 50 W, 3 A,
100 W, 5 A
11 Switching Power Supply S82J
S82J-10005jj (100 W)
S82J-10012jj (100 W)
S82J-10015jj (100 W)
S82J-15024jj (150 W)
+V
–V
DC OutputInput
AC (L)
AC (N)
Fuse*
Noise filter
Inrush current
protection circuit Rectifier
Control circuit
Overcurrent
detector
Rectifier and
smoothing
circuit
Detector
Photocoupler
100 or 200 V
(selected au-
tomatically)
*Fuse capacity
100 W: 5 A
150 W: 8 A
Overvoltage
detection
circuit
Photocoupler
Overvoltage protection circuit
(5 V models only)
S82J-30024 (300 W)
Parallel operation selector
120/230 V (selectable)
Note: Short-circuit the input voltage selector terminals if the input is 100 to
120 VAC. Keep the terminals open if the input is 200 to 230 VAC.
Fuse
10 A
Noise filter
Inrush current
protection circuit Rectifier and
smoothing
circuit
Detector
Photocoupler
Overvoltage
detector
Photocoupler
Control
circuit
Overcurrent
detector
Rectifier and
smoothing circuit
12
Switching Power Supply S82J
S82J-60024 (600 W)
Parallel operation selector
120/230 V (selectable)
Fuse
20 A
Noise filter
Inrush current
protection circuit Rectifier and
smoothing
circuit
Detector
Photocoupler
Photocoupler
Control
circuit
Overcurrent
detector
Fan
Overheat
detector Overvoltage
detector
Rectifier and
smoothing circuit
Note: Short-circuit the input voltage selector terminals if the input is 100 to
120 VAC. Keep the terminals open if the input is 200 to 230 VAC.
13 Switching Power Supply S82J
JGENERATING OUTPUT VOLTAGE (±)
An output of ± can be generated by using two power supplies as shown below, because the power supply produces a floating output.
INPUT
INPUT
+V
–V
+V
–V
Load
Load
If operation amplifiers as loads are connected in series, connect a diode between the positive and negative output terminals of each
Switching Power Supplies as shown in the illustration below. Without these diodes, the Power Supplies may not start when power is
turned on, possibly damaging internal circuits over a period of time.
Use Schottky barrier diodes with a low forward voltage (VF). Other types of diodes will not be effective.
Guidelines for the dielectric strength and current of the diodes are as follows:
Dielectric strength: At least twice the rated output voltage of the Power Supply
Forward current: At least twice the rated output current
No diodes are required for models that allow series operation.
INPUT + V
– V
+ V
– V
INPUT
D1
D2
Load
Load
Load
JSERIES OPERATION
Only models with power ratings of 50/100/150/300/600 W allow series operation.
As shown in the following diagram, the output voltage from each Switching Power Supply can be added.
INPUT
+V
–V
+V
–V
INPUT
Load
D1
D2
With the S82J-050jjjj or S82J-10024jj, if the load is shorted a reverse voltage may result in the Power Supply causing deteriora-
tion and damage. It is recommended that diodes are connected as shown in the previous diagram (D1, D2).
JPARALLEL OPERATION
Only 300- and 600-W models can be in parallel operation. Do not operate any other models in parallel. The output of the models in paral-
lel operation is a maximum of 80% of the rated output.
Set the parallel operation selector to PARALLEL if the Units are in parallel operation and make sure that the thickness and the length of all
wires connected to the load are the same to ensure that the wires will have no voltage drop differences.
INPUT + V
– V
+ V
– V
INPUT
Load
14
Switching Power Supply S82J
Dimensions
Unit: mm (inch)
JFRONT-MOUNTING BRACKET TYPES
S82J-010jjjj (10 W)
Mounting Holes
(Surface Screw Mounting)
Side Mounting
Bottom Mounting
3.5
90 (3.54)
97
(3.82)
65
5
82
Two, 3.5 dia.
3.5 dia.
78
6.5
M3.5 terminal
screw
3.5
28 35 (1.38)
50
17.5
15 Two, M3
For DIN-rail
mounting
bracket
12max.
582
(3.23)
65 (2.56)
Two, M3
78
(3.07)
Two, M3
S82J-025jjjj (25 W)
M3.5 terminal screw Two, 3.5 dia.
Two, M3
For DIN-rail
mounting bracket
124 (4.88)
3.5
97 (3.82)
65
28 40 (1.57)
3.5
112
3.5 dia.
12max.
17.5
21.5 83
6.5
5116
6
Mounting Holes
(Surface Screw Mounting)
Side Mounting
Bottom Mounting
112
(4.41)
Two, M3
Two, M3
65
(2.56)
116
(4.57)
15 Switching Power Supply S82J
Unit: mm (inch)
jjjj
Mounting Holes
Side Mounting
Bottom Mounting
97
(3.82)
65
3.5
161 (6.34)
12
max
.
M3.5 terminal
screw
5
6.5
22 127 Three,
M3 for
DIN-rail
mounting
bracket
150.5
153
3.5
10
28 40
(1.57)
Two, 3.5 dia.
3.5 dia.
7
153
(6.02)
Two, M3
150.5
(5.93)
65 (2.56)
Two, M3
20
20
M3.5 terminal
screw
170
(6.69)
12
max. 4.5
97
(3.82)
65
7
162
160
100
15
25
4.5
28
50
(1.97)
Three, M4
6.5
4.5 dia.
27.5
15
4.5 dia.
5162
(6.38)
65 (2.56)
Two, M4
Two, M4
160
(6.30)
Mounting Holes
Side Mounting
Bottom Mounting
S82J-10024jj (100 W)
16
Switching Power Supply S82J
S82J-10005jj (100 W)
S82J-10012jj (100 W)
S82J-10015jj (100 W)
S82J-15024jj (150 W) 198 (7.80)
188 (7.40)
180
4 max.
4.5
97
(3.82)
50
(1.97)
4.5
89
35
25
55
100
27.5
7
178 3
3
8.1
9.5
M4 x 8
Three, M4
(6 mm max. deep)
4.5 dia.
4.5
dia.
Mounting holes (on both sides)
Mounting Holes
12
max
.
15
Side Mounting
Bottom Mounting
180 (7.09)
82
(3.23)
Two, M4
178 (7.01)
Two, M4
Eight, M4 holes
(depth: 8 max.
on both sides)
Four, M4 holes (depth: 8 max.)
Nine, M4
terminal
screws
Side
4
max.
181 (7.13)
50
(1.97)
100
(3.94)
120
(4.72)
92
(3.62)
150 (5.91)
21
150 (5.91)
Side Mounting
Bottom Mounting
150
(5.91)
50
(1.97)
Four, 4.5 dia.
100
(3.94)
Four, 4.5 dia.
150
(5.91)
17 Switching Power Supply S82J
Unit: mm (inch)
S82J-60024 (600 W)
Four, M4 holes (depth: 8 max. on one side)
Four, M4 holes
(depth: 8 max.)
Eight, M4 holes
(depth: 8 max.
on both sides)
Nine, M4 terminal
screws
169 (6.65)
31
150 (5.91)
50
(1.97)
100
(3.94)
45
(1.77)
170 (6.69)
92
(3.62)
150 (5.91)
100 (3.94)34
Mounting Holes
Side Mounting
Bottom Mounting
Four, 4.5 dia.
Four, 4.5 dia.
150 (5.91)
100
(3.94)
150 (5.91)
50
(1.97)
JMOUNTING BRACKET (INCLUDED WITH POWER SUPPLY UNIT)
S82J 10-/25-/50-/100-W (24-V) Models
Mounting Holes
Using the Mounting Bracket
Attach the mounting bracket to the panel and loosely tighten
the two screws. Insert the projected parts of the bracket (b)
to the square holes of the power supply (a). Then securely
tighten the screws.
1.5 11
9
60
520
31.5
15
20.5
4.7
4.6
11
74
15
Mounting bracket
(b)
(b)
(a)
(a)
Power supply unit
Two, M3
60 (2.36)
20
(0.79)
4.6
Two, 3.5
dia.
18
Switching Power Supply S82J
5
1.5
2.5 2.5
20
6.5
11
23.5
38
15 3
5 dia.
6
1.5
17.5
6
Front Mounting Brackets (Included) Mounting with Brackets
S82J 100-W (5-/12-/15-V) Models or 150-W Models
Mounting bracket
120 MAX
(4.72)
Two, 5 dia.
30±0.5
(1.18)
110
(4.33)
Appearance and Mounting Dimensions
00-W Models
10 dia.
Two, 5 dia.
Note: Using the bracket provides
21.6 mm ventilation space.
Note: Using the bracket provides 23.6 mm ventilation space.
145
(5.71)
90
(3.54)
32
(1.26)
92
(3.62)
48
(1.89)
145 (5.71)
160 (6.30)
145
(5.71)
140 (5.51)
t=1.6
19 Switching Power Supply S82J
JDIN-RAIL MOUNTING BRACKET TYPES
S82J-010jjjD (10 W)
S82J-025jjjD (25 W)
9 max. when slided out
9 max. when slided out
97
(3.82)
40
(1.57) 124 (4.88)
97
(3.82)
134.2 (5.28)
35
(1.38) 90 (3.54)
100.2 (3.94)
S82J-050jjjD (50 W)
S82J-10024jD
(100 W, 24-V Output)
9 max. when slided out
9 max. when slided out
40
(1.57)
97
(3.82)
171.2 (6.74)
161 (6.34)
97
(3.82)
180.2 (7.09)
70 (6.69)
50
(1.97)
20
Switching Power Supply S82J
S82J-10005jD (100 W)
S82J-10012jD (100 W)
S82J-10015jD (100 W)
S82J-15024jD (150 W)
9 max. when slided out
198 (7.80)
188 (7.40)
50
(1.97)
97
(3.82)
198.2 (7.80)
Accessories (Order Separately)
JDIN RAIL (ORDER SEPARATELY)
4.5
15 25 25 25 25
10 10
1,000 (500)
(See Note.)
7.3
35 27
1
15 (5)
(See Note.)
Note: The values shown in parentheses are for the PFP-50N.
4.5
15 25 25 25 25 15
10 10
1,000
35 27 24
16
29.
1 1.5
PFP-100N2
JFRONT-MOUNTING BRACKET FOR S82J-10024A AND S82J-10024D
(ORDER SEPARATELY)
S82Y-J10F
Mounting Holes
Note: The front mounting bracket (above) cannot be used for S82J 100-W (5, 12, 15 V) or 150-W models.
Three, 4.5-dia. holes Three, M4
40
(1.57)
15
(0.59)
15
(0.59)
20
(0.79)
50
(1.97)
50
(1.97)
180 (7.09)
21 Switching Power Supply S82J
JCOVER (ORDER SEPARATELY)
Note: This optional cover is available for the open-frame models also.
Item S82Y-J01K S82Y-J02K S82Y-J05K S82Y-J10K
Applicable supply unit S82J-010jjjj S82J-025jjjj S82J-050jjjj S82J-10024jj
Dimensions
90
8.5 A
96
B
5.6 (A)
Remove screw (A) before attaching the cover to the Power
Supply. Tighten the screw to secure the cover on the Power
Supply.
Note: The derating curve shown in Engineering Data may
change with changes in ambient temperature when
the cover is attached to the Power Supply.
Attaching Cover to Power Supply
Dimensions: A 75 mm (2.95) 109 mm (4.29) 146 mm (5.75) 154 mm (6.06)
B35 mm (1.38) 39 mm (1.54) 38 mm (1.50) 48 mm (1.89)
JFERRITE RING CORE (ORDER SEPARATELY)
JNOISE FILTER (ORDER SEPARATELY)
13 30
39 (1.54)
34 (1.34)
39
(1.54)
16 max. A max.
B
Two, 4.8 dia.
(Mounting
holes)
6.5
4Six, M4
6.5
C
16 max.
4
Nameplate
D
47
(1.85)
82Y-JC-T
82Y-JF3-N for 300-W Models for 200 to 230 VAC input
82Y-JF6-N for 600-W Models for 200 to 230 VAC input
Model A B C D
S82Y-JF3-N 107 (4.21) 75 (2.95) 90 (3.54) 26 (1.02)
S82Y-JF6-N 117 (4.60) 85 (3.35) 100 (3.94) 30 (1.18)
22
Switching Power Supply S82J
(A) Side mounting
(B) Bottom mounting (secured with screws from the inside of
the power supply)
(C) Bottom mounting (secured with screws from the back of
the power supply)
(D) Front mounting
Front mounting is possible with the mounting brackets
provided. Refer to the Dimensions Section.
(A)
(B)
(C)
The following mounting methods are available.
Mounting brackets
(provided)
Metal plate
S82J 100 (5, 12, 15 V)/150 W
(A)
(B)
JMOUNTING METHODS
S82J 10/25/50/100 (24 V) W
The following three mounting methods are available.
(A) Side mounting
(B) Bottom mounting
23 Switching Power Supply S82J
Certain Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these “Terms”) are
deemed part of all catalogs, manuals or other documents, whether elec-
tronic or in w riting, r elating t o t he s ale o f g oods or services (collectively, the
“Goods”) by Omron Electronics LLC and its subsidiary companies (“Sell-
er”). Seller hereby objects to any terms or conditions proposed in Buyer’s
purchase order or other documents w hich a re inconsistent with, o r in addi-
tion to, these Terms. P lease contact y our Omron representative to confirm
any additional terms for sales from your Omron company.
2. Prices. All prices stated are current, subject to change without notice by
Seller. Buyer agrees to pay the price in effect at time of shipment.
3. Discounts. Cash discounts, if any, will apply only on the net amount of in-
voices sent to Buyer after deducting transportation charges, taxes and du-
ties, and will be allowed only if (i) the invoice is paid according to Seller ’s
payment terms and (ii) Buyer has no past due amounts owing to Seller.
4. Orders. Seller will accept no order less than $200 net billing.
5. Governmental Approvals. Buyer shall be responsible for, and shall bear
all costs involved in, obtaining any government approvals required for the
importation or sale of the Goods.
6. Taxes. All taxes, duties and other governmental charges (other than gen-
eral real property and income taxes), including any interest or penalties
thereon, imposed directly or indirectly on Seller or required to be collected
directly or indirectly by Seller for the manufacture, production, sale, deliv -
ery, importation, consumption or use of the Goods sold hereunder (includ-
ing customs d uties a nd s ales, e xcise, use, turnover a nd license taxes) shall
be charged to and remitted by Buyer to Seller.
7. Financial. If t he f inancial p osition o f B uyer a t a ny t ime b ecomes u nsatisfac-
tory to S eller, S eller r eserves t he r ight t o s top s hipments o r r equire s atisfac-
tory security or payment in advance. If Buyer fails to make payment or
otherwise comply with these Terms or any related agreement, Seller may
(without liability and in addition to other remedies) cancel any unshipped
portion of Goods sold hereunder and stop any Goods in t ransit until Buyer
pays all amounts, including amounts payable hereunder, whether or not
then due, which are owing to it by Buyer. Buyer shall in any event remain
liable for all unpaid accounts.
8. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Seller fully against all costs or expenses arising
in connection therewith.
9. Force Majeure. Seller shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires,
floods, strikes or other labor disputes, shortage of labor or materials, acci-
dents t o m achinery, acts o f s abotage, r i ots, d elay i n o r l ack o f transportation
or the requirements of any government authority.
10. Shipping; Delivery. Unless otherwise expressly agreed in writing by Seller:
a. Shipments shall be by a carrier selected by Seller;
b. Such carrier shall act as the agent of Buyer and delivery to such carrier
shall constitute delivery to Buyer;
c. All sales and shipments of Goods shall be FOB shipping point (unless
otherwise stated in writing by Seller), at which point title to and all risk
of loss of the Goods shall pass f rom S eller t o B uyer, provided that Seller
shall retain a security interest in the Goods until the full purchase price
is paid by Buyer;
d. Delivery and shipping dates are estimates only.
e. Seller will package Goods as it deems proper for protection against
normal handling and extra charges apply to special conditions.
11. Claims. Any claim by Buyer against Selle r for shortage or damage to the
Goods occurring before delivery to the c arrier m u st b e p resented i n writing
to S eller w ithin 3 0 d ays o f r eceipt o f s hipment a nd i nclude t he o riginal t rans-
portation bill signed by t he carrier noting t hat t he c arrier r eceived t he G oods
from Seller in the condition claimed.
12. Warranties. (a) Exclusive Warranty. Seller’s exclusive warranty is that the
Goods will be free from defects in materials a nd workmanship for a period
of twelve months from the date of sale by Seller (or such other period ex-
pressed in writing by Seller). Seller disclaims all o ther warranties, e xpress
or implied. (b) Limitations. SELLER MAKES NO WARRANTY OR REP-
RESENTATION, EXPRESS OR IMPLIED, ABOUT NON–INFRINGE-
MENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-
POSE OF THE GOODS. BUYER ACKNOWLEDGES THAT IT ALONE
HAS DETERMINED T HAT THE GOODS WILL SUITABLY M EET T HE R E-
QUIREMENTS OF THEIR INTENDED USE. Seller further disclaims all
warranties and responsibility of any type for claims or expenses based on
infringement by the Goods or otherwise of any intellectual property right.
(c) Buyer Remedy. Seller’s sole obligation hereunder shall be to replace
(in the form originally shipped with Buyer responsible for labor charges for
removal or replacement thereof) the non–complying Good or, at Seller’s
election, to repay or credit Buyer an amount equal to the purchase price
of the Good; provided that in no event shall Seller be responsible for war-
ranty, repair, indemnity or any other claims or expenses regarding the
Goods unless Seller’s a nalysis c onfirms t hat t he G oods w ere p roperly h an-
dled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any goods by Buy-
er must be approved in writing by Seller before shipment. Seller shall not
be liable for the suitability or unsuitability or the results from the use of
Goods in combination with any electrical or electronic components, cir-
cuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given o rally o r i n w rit-
ing, are not to be construed as an amendment or addition to the above
warranty.
13. Damage L imits; E tc. SELLER S HALL N OT B E L IABLE F OR SPECIAL, I N-
DIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR
PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE G OODS, WHETHER SUCH C LAIM I S B ASED I N CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further , in no event
shall liability of Seller exceed the individual price of the Good on which li-
ability is asserted.
14. Indemnities. Buyer shall indemnify and hold harmless Seller, its affiliates
and its employees from and against all liabilities, losses, claims, costs and
expenses (including a ttorney’ s f ees a nd e xpenses) r elated t o any claim, in-
vestigation, litigation or proceeding (whether or not Seller is a party) which
arises or is alleged to arise from Buyer’s acts or omissions under these
Terms or i n a ny w ay w ith r espect to the G oods. Without l imiting t he f orego-
ing, Buyer (at its own expense) shall indemnify and hold harmless Seller
and defend or settle any action brought against Seller to the extent that it
is based on a claim that any Good made to Buyer specifications infringed
intellectual property rights of another party.
15. Property; Confidentiality. The intellectual property embodied in the Goods
is the exclusive property of Seller and its affiliates and Buyer shall not at -
tempt to duplicate it in any way without the written permission of Seller.
Notwithstanding any charges to Buyer for engineering or tooling, all engi-
neering and tooling shall remain the exclusive property of Seller. All infor-
mation and materials supplied by Seller to Buyer relating to t he Goods are
confidential and proprietary, and Buyer shall limit distribution thereof to its
trusted employees and strictly prevent disclosure to any third party.
16. Miscellaneous. (a) Waiver. No failure or delay by Seller in exercising any
right and no course of dealing between Buyer and Seller shall operate as
a waiver of rights b y Seller. (b) A ssignment. B uyer m ay not a ssign its r ights
hereunder without Seller’s written consent. (c) A mendment. These Terms
constitute the entire agreement between Buyer and Seller relating to the
Goods, and no provision may be changed or waived unless in writing
signed by the parties. (d) Severability. If any provision hereof is rendered
ineffective o r i nvalid, s uch p rovision s hall n ot i nvalidate a ny o ther p rovision.
(e) Setoff. Buyer shall have no right to set off any amounts against the
amount owing in respect of this invoice. (f) As used herein, “including”
means “including without limitation”.
Certain Precautions on Specifications and Use
1. Suitability of Use. Seller shall not be responsible for conformity with any
standards, codes or regulations which apply to the combination of the
Good in the Buyer’s application or use of the Good. At Buyer ’s request,
Seller will provide applicable third party certification documents identifying
ratings and limitations o f u se w hich apply to the Good. This information by
itself is not sufficient for a complete determ ination of the suitability of the
Good in combination with the end product, machine, system, or other ap -
plication or u se. T he following are some examples of a pplications for w hich
particular attention must b e given. T his i s n ot i ntended t o b e a n exhaustive
list of all p ossible u ses o f this Good, nor is i t i ntended t o i mply t hat t he u ses
listed may be suitable for this Good:
(i) Outdoor use, uses involving potential chemical contamination or
electrical interference, or conditions or uses not described in this
document.
(ii) Energy control systems, combustion systems, railroad systems,
aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or
government regulations.
(iii)Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to
this Good.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SE-
RIOUS RISK T O L IFE OR PROPERTY WITHOUT E NSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE
RISKS, AND THAT THE SELLER’S PRODUCT IS PROPERLY RATED
AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
2. Programmable Products. S eller shall not be responsible for the user’s pro-
gramming of a programmable Good, or any consequence thereof.
3. Performance Data. Performance data given in this catalog is provided as
a guide f or the u ser i n d etermining s uitability and d oes not c onstitute a w ar-
ranty. It may represent the result of Seller ’s test conditions, and the user
must correlate it to actual application requirements. Actual performance
is subject to the Seller ’s Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are
changed, or when significant construction changes are made. However,
some specifications of the Good may be changed without any notice.
When in doubt, special part numbers may be assigned to fix or establish
key specifications for your application. Please consult with your Seller ’s
representative at any time to confirm actual specifications of purchased
Good.
5. Errors and Omissions. The information in this catalog has been carefully
checked and is believed to be accurate; however, no responsibility is as -
sumed for clerical, typographical or proofreading errors, or omissions.
24
Switching Power Supply S82J