PACDN006 6 Channel ESD Protection Array Features Product Description * * The PACDN006 is a diode array designed to provide 6 channels of ESD protection for electronic components or sub-systems. Each channel consists of a pair of diodes which steers an ESD current pulse to either the positive (VP) or negative (VN) supply. The PACDN006 protects against ESD pulses up to 15kV Human Body Model (100 pF capacitor discharging through a 1.5K resistor), and 8kV contact discharge, per International Standard IEC 61000-4-2. * * * * * Six channels of ESD protection +8 kV contact, +15 kV air ESD protection per per channel (IEC 61000-4-2 standard) +15 kV of ESD protection per channel (HBM) Low loading capacitance (3pF typical) Low leakage current is ideal for battery-powered devices Available in miniature 8-pin MSOP package RoHS compliant (lead-free) finishing This device is particularly well-suited for portable electronics (e.g., cellular phones, PDAs, notebook computers) because of its small package footprint, high ESD protection level, and low loading capacitance. It is also suitable for protecting video output lines and I/O ports in computers and peripherals and is ideal for a wide range of consumer electronics products. Applications * * * * * * * Consumer electronic products Cellular phones PDAs Notebook computers Desktop PCs Digital cameras and camcorders VGA (video) port protection for desktop and portable PCs The PACDN006 is available with RoHS compliant leadfree finishing. Typical Application Circuit Electrical Schematic VCC 8 3 PACDN006 7 6 5 2 3 4 VP 1 24 5 6 8 VN Expansion Connector I/O Port Buffers 7 0.22uF* Handheld/PDA ESD Protection 1 * Decoupling capacitor must be placed as close as possible to Pin7. (c) 2008 California Micro Devices Corp. All rights reserved. 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Issue B - 06/17/08 Fax: 408.263.7846 www.cmd.com 1 PACDN006 PACKAGE / PINOUT DIAGRAMS TOP VIEW 1 CH 2 2 VN 3 CH 3 4 006R CH 1 8 CH 6 7 VP 6 CH 5 5 CH 4 8-pin MSOP Note: This drawing is not to scale. PIN DESCRIPTIONS PIN NAME TYPE DESCRIPTION 1 CH 1 I/O ESD Channel. 2 CH 2 I/O ESD Channel. 3 VN GND 4 CH 3 I/O ESD Channel. 5 CH 4 I/O ESD Channel. 6 CH 5 I/O ESD Channel. 7 VP Supply 8 CH 6 I/O Negative voltage supply rail or ground reference rail. Positive voltage supply rail. ESD Channel. Ordering Information PART NUMBERING INFORMATION Pins Package Ordering Part Number1 Part Marking 8 MSOP PACDN006MR 006R Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. (c) 2008 California Micro Devices Corp. All rights reserved. 2 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Issue B - 06/17/08 Fax: 408.263.7846 www.cmd.com PACDN006 Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS Supply Voltage (VP - VN) 6.0 V Diode Forward DC Current (Note 1) 20 mA Operating Temperature Range -40 to +85 C Storage Temperature Range -65 to +150 C (VN - 0.5) to (VP + 0.5) V 200 mW DC Voltage at any channel input Package Power Rating Note 1: Only one diode conducting at a time. STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range Operating Supply Voltage (VP - VN) RATING UNITS -40 to +85 C 0 to 5.5 V ELECTRICAL OPERATING CHARACTERISTICS(SEE NOTE 1) SYMBOL PARAMETER CONDITIONS IP Supply Current (VP-VN)=5.5V VF Diode Forward Voltage IF = 20mA VESD Channel Clamp Voltage Positive Transients Negative Transients VCL ILEAK CIN ESD Protection Peak Discharge Voltage at any channel input, in system a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 c) Air Discharge per IEC 61000-4-2 MIN TYP 0.65 MAX UNITS 10 A 0.95 V Note 3 Notes 2,4 +15 kV Note 5 Note 5 +8 +15 kV kV @15kV ESD HBM Channel Leakage Current Channel Input Capacitance VP + 13.0 VN - 13.0 V V +0.1 +1.0 A 3 5 pF @ 1 MHz, VP=5V, VN=0V, VIN=2.5V; Note 2 applies Note 1: All parameters specified at TA=25C unless otherwise noted. VP = 5V, VN = 0V unless noted. Note 2: These parameters guaranteed by design and characterization. Note 3: From I/O pins to VP or VN only. VP bypassed to VN with a 0.22F ceramic capacitor (see Application Information for more details). Note 4: Human Body Model per MIL-STD-883, Method 3015, CDischarge = 100pF, RDischarge = 1.5K, VP = 5.0V, VN grounded. Note 5: Standard IEC 61000-4-2 with CDischarge = 150pF, RDischarge = 330, VP = 5.0V, VN grounded. (c) 2008 California Micro Devices Corp. All rights reserved. 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Issue B - 06/17/08 Fax: 408.263.7846 www.cmd.com 3 PACDN006 Performance Information Input Capacitance vs. Input Voltage 5 CIN (pF) 4 3 2 1 0 0 1 2 3 4 5 VIN Typical Variation of CIN vs. VIN (VP = 5V, VN = 0V, 0.1 F chip capacitor between VP and VN) (c) 2008 California Micro Devices Corp. All rights reserved. 4 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Issue B - 06/17/08 Fax: 408.263.7846 www.cmd.com PACDN006 Application Information Design Considerations a ROUT of 1 ohm would result in a 10V increment in VCL for a peak IESD of 10A. In order to realize the maximum protection against ESD pulses, care must be taken in the PCB layout to minimize parasitic series inductances on the Supply/ Ground rails as well as the signal trace segment between the signal input (typically a connector) and the ESD protection device. Refer to Figure 1, which illustrates an example of a positive ESD pulse striking an input channel. The parasitic series inductance back to the power supply is represented by L1 and L2. The voltage VCL on the line being protected is: If the inductances and resistance described above are close to zero, the rail-clamp ESD protection diodes will do a good job of protection. However, since this is not possible in practical situations, a bypass capacitor must be used to absorb the very high frequency ESD energy. So for any brand of rail-clamp ESD protection diodes, a bypass capacitor should be connected between the VP pin of the diodes and the ground plane (VN pin of the diodes) as shown in the Application Circuit diagram below. A value of 0.22F is adequate for IEC-61000-4-2 level 4 contact discharge protection (+8kV). Ceramic chip capacitors mounted with short printed circuit board traces are good choices for this application. Electrolytic capacitors should be avoided as they have poor high frequency characteristics. For extra protection, connect a zener diode in parallel with the bypass capacitor to mitigate the effects of the parasitic series inductance inherent in the capacitor. The breakdown voltage of the zener diode should be slightly higher than the maximum supply voltage. VCL = Fwd voltage drop of D1 + VSUPPLY + L1 x d(IESD ) / dt + L2 x d(IESD ) / dt where IESD is the ESD current pulse, and VSUPPLY is the positive supply voltage. An ESD current pulse can rise from zero to its peak value in a very short time. As an example, a level 4 contact discharge per the IEC61000-4-2 standard results in a current pulse that rises from zero to 30 Amps in 1ns. Here d(IESD)/dt can be approximated by IESD/t, or 30/(1x10-9). So just 10nH of series inductance (L1 and L2 combined) will lead to a 300V increment in VCL! As a general rule, the ESD Protection Array should be located as close as possible to the point of entry of expected electrostatic discharges. The power supply bypass capacitor mentioned above should be as close to the VP pin of the Protection Array as possible, with minimum PCB trace lengths to the power supply, ground planes and between the signal input and the ESD device to minimize stray series inductance. Similarly for negative ESD pulses, parasitic series inductance from the VN pin to the ground rail will lead to drastically increased negative voltage on the line being protected. Another consideration is the output impedance of the power supply for fast transient currents. Most power supplies exhibit a much higher output impedance to fast transient current spikes. In the VCL equation above, the VSUPPLY term, in reality, is given by (VDC + IESD x ROUT), where VDC and ROUT are the nominal supply DC output voltage and effective output impedance of the power supply respectively. As an example, Additional Information See also California Micro Devices Application Notes AP209, "Design Considerations for ESD Protection" and AP219, "ESD Protection for USB 2.0 Systems"" L2 POSITIVE SUPPLY RAIL VP PATH OF ESD CURRENT PULSE IESD D1 L1 0.22F D2 ONE CHANNEL OF PACDN006 LINE BEING PROTECTED SYSTEM OR CIRCUITRY BEING PROTECTED CHANNEL INPUT 20A VCL 0A GROUND RAIL VN CHASSIS GROUND Figure 1. Application of Positive ESD Pulse between Input Channel and Ground (c) 2008 California Micro Devices Corp. All rights reserved. 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Issue B - 06/17/08 Fax: 408.263.7846 www.cmd.com 5 PACDN006 Mechanical Details MSOP-8 Mechanical Specifications, 8 pin The PACDN006 is supplied in a 8-pin MSOP package. Dimensions are presented below. Mechanical Package Diagrams TOP VIEW For complete information on the MSOP-8, see the California Micro Devices MSOP Package Information document. D 8 7 6 5 PACKAGE DIMENSIONS Package MSOP Pins 8 Dimensions Millimeters Pin 1 Marking Inches Min Max Min Max A 0.75 0.95 0.030 0.037 A1 0.05 0.15 0.002 0.006 B 0.28 0.38 0.011 0.015 C 0.13 0.23 0.005 0.009 D 2.90 3.10 0.114 0.122 E 2.90 3.10 0.114 0.122 e 0.65 BSC 0.026 BSC H 4.90 BSC 0.193 BSC L 0.40 # per tape and reel 0.70 E H 0.016 1 2 3 4 SIDE VIEW A SEATING PLANE A1 B e 0.028 END VIEW 4000 pieces C Controlling dimension: millimeters L Dimensions for MSOP-8 Package (c) 2008 California Micro Devices Corp. All rights reserved. 6 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Issue B - 06/17/08 Fax: 408.263.7846 www.cmd.com