Product Folder Sample & Buy Support & Community Tools & Software Technical Documents DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 DS8921x Differential Line Driver and Receiver Pair 1 Features 3 Description * * * * * The DS8921, DS8921A, and DS8921AT devices are differential line driver and receiver pairs designed specifically for applications meeting the ST506, ST412, and ESDI disk drive standards. In addition, these devices meet the requirements of the EIA standard RS-422. 1 * * * 12-ns Typical Propagation Delay Output Skew: 0.5 ns Typical Meets the Requirements of EIA Standard RS-422 Complementary Driver Outputs High Differential or Common-Mode Input Voltage Ranges of 7 V 0.2 V Receiver Sensitivity Over the Input Voltage Range Receiver Input Hysteresis: 70 mV Typical DS8921AT Industrial Temperature Operation: (-40C to +85C) 2 Applications * Differential Line Driver and Receiver for: - ST506 Disk Drive Standard - ST412 Disk Drive Standard - ESDI Disk Drive Standard - RS-422 Interface The DS8921x receivers offer an input sensitivity of 200 mV over a 7 V common mode operating range. Hysteresis is incorporated (typically 70 mV) to improve noise margin for slowly changing input waveforms. The DS8921x drivers are designed to provide unipolar differential drive to twisted-pair or parallel wire transmission lines. Complementary outputs are logically ANDed and provide an output skew of 0.5 ns (typical) with propagation delays of 12 ns. The DS8921x devices are designed to be compatible with TTL and CMOS. Device Information(1) PART NUMBER DS8921 DS8921A DS8921AT PACKAGE BODY SIZE (NOM) SOIC (8) 4.90 mm x 3.91 mm PDIP (8) 9.81 mm x 6.35 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. SPACE Typical Application Block Diagram Simplified Functional Block Diagram RI+ RO RI- DO+ DI DO5.0 V VCC GND 0.1 F 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 3 4 4 4 5 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Electrical Characteristics........................................... Receiver Switching Characteristics .......................... Driver Switching Characteristics: Single-Ended Characteristics ........................................................... 6.7 Driver Switching Characteristics: Differential Characteristics ........................................................... 6.8 Typical Characteristics .............................................. 7 9 Overview ................................................................... Functional Block Diagram ......................................... Feature Description................................................... Device Functional Modes.......................................... 8 8 8 8 Application and Implementation .......................... 9 9.1 Application Information.............................................. 9 9.2 Typical Application .................................................... 9 10 Power Supply Recommendations ..................... 12 11 Layout................................................................... 12 11.1 Layout Guidelines ................................................. 12 11.2 Layout Example .................................................... 12 12 Device and Documentation Support ................. 13 5 5 6 Parameter Measurement Information .................. 6 7.1 AC Test Circuits and Switching Diagrams ................ 6 8 8.1 8.2 8.3 8.4 12.1 12.2 12.3 12.4 Related Links ........................................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 13 13 13 13 13 Mechanical, Packaging, and Orderable Information ........................................................... 13 Detailed Description .............................................. 8 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision C (April 2013) to Revision D * Page Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................. 1 Changes from Revision B (November 2004) to Revision C * 2 Page Changed layout of National Data Sheet to TI format. ........................................................................................................... 1 Submit Documentation Feedback Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT DS8921, DS8921A, DS8921AT www.ti.com SNLS374D - MAY 1998 - REVISED JANUARY 2015 5 Pin Configuration and Functions D, P Package 8 Pins Top View Pin Functions PIN NAME NO. I/O DESCRIPTION DIFFERENTIAL SIGNALING I/O DI 3 I TTL/CMOS Compatible Driver Input DO+, DO- 6, 5 O Inverting and non-inverting differential driver outputs RI+, RI- 8, 7 I Inverting and non-inverting differential receiver inputs 2 O Receiver Output Pin GND 4 Power Ground Pin VCC 1 Power Supply pin, provide 5-V supply RO POWER 6 Specifications 6.1 Absolute Maximum Ratings (1) (2) MIN Supply Voltage -0.5 Driver Input Voltage Output Voltage Receiver Output Sink Current MAX UNIT 7 V 7 V 5.5 V 50 mA Receiver Input Voltage -10 10 V Differential Input Voltage -12 12 V 730 mW Maximum Package Power Dissipation at 25C: D Package Maximum Package Power Dissipation at 25C: P Package 1160 mW 9.3 mW/C Derate P Package, above 25C 5.8 mW/C Lead Temperature 260 C 260 C 150 C 165 C Derate D Package, above 25C (Soldering, 4 sec.) Maximum Junction Temperature -65 Storage Temperature, Tstg (1) (2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the Texas Instrument Sales Office/ Distributors for availability and specifications. Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT Submit Documentation Feedback 3 DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 www.ti.com 6.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 2000 Charged-device model (CDM), per JEDEC specification JESD22C101 (2) 1500 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions MIN MAX 4.5 5.5 V 0 70 C -40 85 C MIN TYP MAX UNIT +200 mV Supply Voltage Temperature (TA): DS8921/DS8921A Temperature (TA): DS8921AT UNIT 6.4 Electrical Characteristics Over operating free-air temperature range unless otherwise noted. (1) (2) (3) TEST CONDITIONS RECEIVER VTH -7 V VCM +7 V -200 35 VHYST -7 V VCM +7 V 15 70 RIN VIN = -7 V, +7 V, (Other Input = GND) 4.0 6.0 VIN = 10 V IIN VIN = -10 V VOH IOH = -400 A VOL IOL = 8 mA ISC VCC = MAX, VOUT = 0 V mV k 3.25 mA -3.25 mA 2.5 V 0.5 -15 -100 V mA DRIVER VIH 2.0 V VIL -40 0.8 V -200 A IIL VCC = MAX, VIN = 0.4 V IIH VCC = MAX, VIN = 2.7 V 20 A II VCC = MAX, VIN = 7.0 V 100 A VCL VCC = MIN, IIN = -18 mA -1.5 V VOH VCC = MIN, IOH = -20 mA VOL VCC = MIN, IOL = +20 mA 0.5 V IOFF VCC = 0V, V OUT = 5.5 V 100 A 0.4 V 2.5 |VT| - |VT| VT 2.0 |VOS - VOS| ISC V V 0.4 VCC = MAX, VOUT = 0 V -30 V -150 mA 35 mA DRIVER AND RECEIVER ICC (1) (2) (3) 4 VCC = MAX, VOUT = Logic 0 All currents into device pins are shown as positive values; all currents out of the device are shown as negative; all voltages are referenced to ground unless otherwise specified. All values shown as max or min are classified on absolute value basis. All typical values are VCC = 5 V, TA = 25C. Only one output at a time should be shorted. Submit Documentation Feedback Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT DS8921, DS8921A, DS8921AT www.ti.com SNLS374D - MAY 1998 - REVISED JANUARY 2015 6.5 Receiver Switching Characteristics TEST CONDITIONS tpLH MIN CL = 30 pF TYP MAX 8921 MAX 8921A MAX 8921AT 14 22.5 20 20 ns 14 22.5 20 20 ns 0.5 5 3.5 5 ns TYP MAX 8921 MAX 8921A MAX 8921AT 10 15 15 15 ns 10 15 15 15 ns 5 8 8 9.5 ns 5 8 8 9.5 ns 1 5 3.5 3.5 ns TYP MAX 8921 MAX 8921A MAX 8921AT 10 15 15 15 ns 10 15 15 15 ns 0.5 6 2.75 2.75 ns UNIT (Figure 3 and Figure 4) tpHL CL = 30 pF (Figure 3 and Figure 4) |tpLH-t pHL| CL = 30 pF (Figure 3 and Figure 4) 6.6 Driver Switching Characteristics: Single-Ended Characteristics TEST CONDITIONS tpLH MIN CL = 30 pF UNIT (Figure 5 and Figure 6) tpHL CL = 30 pF (Figure 5 and Figure 6) tTLH CL = 30 pF (Figure 9 and Figure 10) tTHL CL = 30 pF (Figure 9 and Figure 10) Skew CL = 30 pF (1) (Figure 5 and Figure 6) (1) Difference between complementary outputs at the 50% point. 6.7 Driver Switching Characteristics: Differential Characteristics (1) TEST CONDITIONS tpLH MIN CL = 30 pF UNIT (Figure 5, Figure 7, and Figure 8) tpHL CL = 30 pF (Figure 5, Figure 7, and Figure 8) |tpLH-t pHL| CL = 30 pF (Figure 5, Figure 7, and Figure 8) (1) Differential Delays are defined as calculated results from single ended rise and fall time measurements. This approach in establishing AC performance specifications has been taken due to limitations of available Automatic Test Equipment (ATE). The calculated ATE results assume a linear transition between measurement points and are a result of the following equations: Tcr = Crossing Point Tra, Trb, Tfa and T fb are time measurements with respect to the input. See Figure 8. Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT Submit Documentation Feedback Where: 5 DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 www.ti.com 6.8 Typical Characteristics Test Setup: Figure 5. Data Rate, Test Pattern: 2 Mbps, 1010 Pattern. T: 25C 5.2 5.8 T(THL) High to Low Transition Time (ns) Low to High Transition Time (ns) T(TLH) 5.0 4.8 4.6 5.6 5.4 5.2 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 Supply Voltage (V) 5.5 4.5 4.6 4.7 Figure 1. Typical Driver Output Low to High Transition Time vs Supply Voltage 4.8 4.9 5.0 5.1 Supply Voltage (V) C004 5.2 5.3 5.4 5.5 C005 Figure 2. Typical Driver Output High to Low Transition Time vs Supply Voltage 7 Parameter Measurement Information 7.1 AC Test Circuits and Switching Diagrams Figure 3. Test Circuit for Receiver Output Figure 4. Receiver Propagation Delay C2 D C1 R1 C3 NOTE:R1= 100 Ohms, C1 = C2 = C3 = 30 pF Figure 5. Driver Test Circuit 6 Submit Documentation Feedback Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT DS8921, DS8921A, DS8921AT www.ti.com SNLS374D - MAY 1998 - REVISED JANUARY 2015 AC Test Circuits and Switching Diagrams (continued) Figure 6. Driver Single-Ended Propagation Delay Figure 7. Driver Differential Propagation Delay Figure 8. Driver Delay ATE Testing Figure 9. Driver Output Transition Time Figure 10. Driver Output Transition Time Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT Submit Documentation Feedback 7 DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 www.ti.com 8 Detailed Description 8.1 Overview The DS8921x devices are each a differential line driver and receiver pair in a single package. The devices are designed specifically for ST506, ST412, and ESDI disk drive standards, as well as RS-422 interface applications. The DS8921 and DS8921A are rated at a commercial temperature range of 0C to 70C, whereas the DS8921AT is rated at an extended temperature range of -40C to +85C. 8.2 Functional Block Diagram RI+ RO RI- DO+ DI DO5.0 V VCC GND 0.1 F 8.3 Feature Description The DS8921x devices each contain a differential driver and receiver. The driver converts a TTL or CMOS input to complementary outputs that provide differential drive to a twistedpair or parallel wire transmission line. The receiver converts the differential signals at its input pins to a TTL output. The receiver offers an input sensitivity of 200 mV and supports a common-mode input voltage of 7 V. 8.4 Device Functional Modes Table 1. Function Table RECEIVER INPUT OUTPUT INPUT RI+, RI- RO DI DO+ DO- 1 1 1 0 0 0 0 1 VID (1) VTH (MAX) VID (1) VTH (MIN) Open (1) 8 DRIVER OUTPUT 1 VID is the input differential voltage between RI+ and RI-. Submit Documentation Feedback Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT DS8921, DS8921A, DS8921AT www.ti.com SNLS374D - MAY 1998 - REVISED JANUARY 2015 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information The DS8921 is a differential line driver and receiver pair in a single package, designed for applications for the ST506, ST412, and ESDI Disk Drive Standards. The DS8921 is compatible to EIA RS-422 signaling standards, supporting 200-mV input sensitivity across a 7-V common mode operating range. This transceiver is intended for driving differential signal across long transmission lines and translating received differential signals into their CMOS/TTL single-ended equivalence. The DS8921 transmits and reproduces received data in communications links where ground reference difference, or noisy environment are common. 9.2 Typical Application Figure 11 shows a typical implementation of the DS8921x device in a ST506 and ST412 disk drive application. The differential outputs of the driver are connected to a twisted-pair transmission line, carrying data from the driver to the differential receiver at the other end of the cable. A differential termination resistor should be connected across the input pins of the receiver. Figure 11. ST506 and ST412 Application Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT Submit Documentation Feedback 9 DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 www.ti.com Typical Application (continued) 9.2.1 Design Requirements * Apply TTL or LVCMOS signal to driver input at DI * Transmit complementary outputs at DO+ and DO* Receive complimentary input signals at RI+ and RI* Receive TTL output signal at RO * Use controlled-impedance transmission lines such as printed circuit board traces, twisted-pair wires or parallel wire cable * Place terminating resistor at the far end of the differential pair 9.2.2 Detailed Design Procedure * Connect VCC and GND pins to the power and ground planes of the printed circuit board, with 0.1-uF bypass capacitor * Use TTL/LVCMOS logic levels at DI and RO * Use controlled-impedance transmission media for the differential signals DI+- and RO+* Place a terminating resistor at the far-end of the differential pair to avoid reflection * Ensure the received complimentary signals at RO+ and RO- are within the signal threshold of 200 mV Data Signal (2 V/DIV) Data Signal (2 V/DIV) 9.2.3 Application Curves 0V 0V Time (400 ns/DIV) 10 Time (400 ns/DIV) 2.0 Mbps Single-Ended 1010 Data Pattern 2.0 Mbps Differential Data Pattern Note: The input for the driver is Figure 12 Figure 12. Driver Single-Ended Input Signal Figure 13. Driver Differential Output Signal Submit Documentation Feedback Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT DS8921, DS8921A, DS8921AT www.ti.com SNLS374D - MAY 1998 - REVISED JANUARY 2015 Data Signal (2 V/DIV) Data Signal (2 V/DIV) Typical Application (continued) 0V 0V Time (400 ns/DIV) 2.0 Mbps Differential Data Pattern Figure 14. Receiver Differential Input Signal Time (400 ns/DIV) 2.0 Mbps Single-Ended 1010 Data Pattern Note: The input for the receiver is Figure 14 Figure 15. Receiver Single-Ended Output Signal Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT Submit Documentation Feedback 11 DS8921, DS8921A, DS8921AT SNLS374D - MAY 1998 - REVISED JANUARY 2015 www.ti.com 10 Power Supply Recommendations TI recommends connecting the supply (VCC) and ground (GND) pins to power planes that are routed on adjacent layers of the PCB. Additionally, careful attention should be paid to bypassing the supply using a capacitor. A 0.1-F bypass capacitor should be connected to the VCC pin such that the capacitor is as close as possible to the device. 11 Layout 11.1 Layout Guidelines High-speed interconnects should be treated as transmission lines with a controlled impedance. The differential interconnect can be a pair of printed-circuit board (PCB) traces, twisted-pair wires, or a parallel wire cable. A termination resistor should be placed at the differential input, and the resistor value should be approximately the same as the differential impedance of the transmission line to minimize reflections. It is preferable to connect the VCC and GND pins to the power and ground planes using plated-through-holes. Additionally, a 0.1-F bypass capacitor should be placed close to the VCC pin across VCC and GND. Place a terminating resistor at the receiving end of the interconnect transmission line, as close as possible to the input pins of the receiver. The terminating resistor value should be approximately the same as the differential pair impedance to minimize reflection, and the transmission line should have a controlled impedance with minimum impedance discontinuities. The input and output differential signals of the device should have traces that are routed exclusively on one layer of the board, and the differential pairs should also be routed away from other differential pairs in order to minimize crosstalk between transmission lines. Additionally, the differential pairs should have a controlled impedance with minimum impedance discontinuities and be terminated with a resistor that is closely matched to the differential pair impedance in order to minimize transmission line reflections. The differential pairs should be routed with uniform trace width and spacing to minimize impedance mismatch. 11.2 Layout Example Via to GND Plane Via to VCC Plane 1 5 RX Differential Pair Bypass Capacitor Termination Resistor 6 2 DS8921/DS8921A/DS8921AT 3 7 TX Differential Pair Via to GND Plane 4 8 Figure 16. DS8921 Example Layout 12 Submit Documentation Feedback Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT DS8921, DS8921A, DS8921AT www.ti.com SNLS374D - MAY 1998 - REVISED JANUARY 2015 12 Device and Documentation Support 12.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 2. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY DS8921 Click here Click here Click here Click here Click here DS8921A Click here Click here Click here Click here Click here DS8921AT Click here Click here Click here Click here Click here 12.2 Trademarks All trademarks are the property of their respective owners. 12.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.4 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright (c) 1998-2015, Texas Instruments Incorporated Product Folder Links: DS8921 DS8921A DS8921AT Submit Documentation Feedback 13 PACKAGE OPTION ADDENDUM www.ti.com 25-Aug-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) DS8921AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS89 21AM DS8921AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS89 21AM DS8921ATM OBSOLETE SOIC D 8 TBD Call TI Call TI -40 to 85 DS892 1ATM DS8921ATM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 DS892 1ATM DS8921M/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS892 1M DS8921MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS892 1M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Aug-2018 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DS8921AMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 DS8921MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS8921AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 DS8921MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DS8921AM DS8921AM/NOPB DS8921AMX DS8921AMX/NOPB DS8921ATM DS8921ATM/NOPB DS8921M/NOPB DS8921MX DS8921MX/NOPB DS8921N/NOPB