PCA9534 8-bit I2C-bus and SMBus low power I/O port with interrupt Rev. 03 -- 6 November 2006 Product data sheet 1. General description The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc. The PCA9534 consists of an 8-bit Configuration register (Input or Output selection); 8-bit Input register, 8-bit Output register and an 8-bit Polarity Inversion register (active HIGH or active LOW operation). The system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The polarity of the Input Port register can be inverted with the Polarity Inversion register. All registers can be read by the system master. Although pin-to-pin and I2C-bus address compatible with the PCF8574 series, software changes are required due to the enhancements and are discussed in Application Note AN469. The PCA9534 is identical to the PCA9554 except for the removal of the internal I/O pull-up resistor which greatly reduces power consumption when the I/Os are held LOW. The PCA9534 open-drain interrupt output is activated when any input state differs from its corresponding input port register state and is used to indicate to the system master that an input state has changed. The power-on reset sets the registers to their default values and initializes the device state machine. Three hardware pins (A0, A1, A2) vary the fixed I2C-bus address and allow up to eight devices to share the same I2C-bus/SMBus. 2. Features n n n n n n n n n 8-bit I2C-bus GPIO Operating power supply voltage range of 2.3 V to 5.5 V 5 V tolerant I/Os Polarity Inversion register Active LOW interrupt output Low standby current Noise filter on SCL/SDA inputs No glitch on power-up Internal power-on reset PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt n 8 I/O pins which default to 8 inputs n 0 Hz to 400 kHz clock frequency n ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA n Offered in four different packages: SO16, TSSOP16, and HVQFN16 (4 x 4 x 0.85 mm and 3 x 3 x 0.85 mm versions) 3. Ordering information Table 1. Ordering information Tamb = -40 C to +85 C. Type number Topside mark Package Name Description Version PCA9534D PCA9534D SO16 plastic small outline package; 16 leads; body width 7.5 mm SOT162-1 PCA9534PW PCA9534 TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 PCA9534BS 9534 HVQFN16 plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 4 x 4 x 0.85 mm SOT629-1 PCA9534BS3 P34 HVQFN16 plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 3 x 3 x 0.85 mm SOT758-1 4. Block diagram PCA9534 A0 A1 A2 IO0 IO1 8-bit SCL SDA INPUT FILTER I2C-BUS/SMBus CONTROL write pulse VDD IO2 INPUT/ OUTPUT PORTS IO3 IO4 IO5 IO6 read pulse POWER-ON RESET IO7 VDD VSS INT LP FILTER 002aac469 All I/Os are set to inputs at reset. Fig 1. Block diagram of PCA9534 PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 2 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 5. Pinning information 5.1 Pinning A0 1 A1 2 16 VDD 15 SDA A0 1 A1 2 16 VDD 15 SDA 14 SCL A2 3 14 SCL A2 3 IO0 4 13 INT IO0 4 IO1 5 12 IO7 IO1 5 IO2 6 11 IO6 IO2 6 11 IO6 IO3 7 10 IO5 IO3 7 10 IO5 VSS 8 9 VSS 8 IO4 IO0 2 12 SCL A2 1 11 INT IO0 2 13 SDA 16 A1 terminal 1 index area 15 A0 Fig 3. Pin configuration for TSSOP16 13 SDA 14 VDD 15 A0 16 A1 1 IO4 002aac466 Fig 2. Pin configuration for SO16 A2 12 IO7 9 002aac465 terminal 1 index area 13 INT PCA9534PW 14 VDD PCA9534D 12 SCL 11 INT PCA9534BS PCA9534BS3 Transparent top view 6 7 8 VSS IO4 IO5 002aac467 5 9 IO6 IO3 4 8 IO2 IO5 IO2 7 10 IO7 6 3 9 IO4 IO1 4 VSS 10 IO7 5 3 IO3 IO1 IO6 002aac468 Transparent top view Fig 4. Pin configuration for HVQFN16 (SOT629-1; 4 x 4 x 0.85 mm) Fig 5. Pin configuration for HVQFN16 (SOT758-1; 3 x 3 x 0.85 mm) 5.2 Pin description Table 2. Symbol Pin description Pin Description SO16, TSSOP16 HVQFN16 A0 1 15 address input 0 A1 2 16 address input 1 A2 3 1 address input 2 IO0 4 2 input/output 0 IO1 5 3 input/output 1 IO2 6 4 input/output 2 IO3 7 5 input/output 3 VSS 8 6[1] ground supply voltage IO4 9 7 input/output 4 IO5 10 8 input/output 5 PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 3 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt Table 2. Symbol Pin description ...continued Pin Description SO16, TSSOP16 HVQFN16 IO6 11 9 input/output 6 IO7 12 10 input/output 7 INT 13 11 interrupt output (open-drain) SCL 14 12 serial clock line SDA 15 13 serial data line VDD 16 14 supply voltage [1] HVQFN package die supply ground is connected to both VSS pin and exposed center pad. VSS pin must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the PCB in the thermal pad region. 6. Functional description Refer to Figure 1 "Block diagram of PCA9534". 6.1 Registers 6.1.1 Command byte Table 3. Command byte Command Protocol Function 0 read byte Input Port register 1 read/write byte Output Port register 2 read/write byte Polarity Inversion register 3 read/write byte Configuration register The command byte is the first byte to follow the address byte during a write transmission. It is used as a pointer to determine which of the following registers will be written or read. 6.1.2 Register 0 - Input Port register This register is a read-only port. It reflects the incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output by Register 3. Writes to this register have no effect. The default `X' is determined by the externally applied logic level. PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 4 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt Table 4. Register 0 - Input Port register bit description Bit Symbol Access Value Description 7 I7 read only X determined by externally applied logic level 6 I6 read only X 5 I5 read only X 4 I4 read only X 3 I3 read only X 2 I2 read only X 1 I1 read only X 0 I0 read only X 6.1.3 Register 1 - Output Port register This register reflects the outgoing logic levels of the pins defined as outputs by Register 3. Bit values in this register have no effect on pins defined as inputs. Reads from this register return the value that is in the flip-flop controlling the output selection, not the actual pin value. Table 5. Register 1 - Output Port register bit description Legend: * default value. Bit Symbol Access Value Description 7 6 O7 R 1* O6 R 1* reflects outgoing logic levels of pins defined as outputs by Register 3 5 O5 R 1* 4 O4 R 1* 3 O3 R 1* 2 O2 R 1* 1 O1 R 1* 0 O0 R 1* 6.1.4 Register 2 - Polarity Inversion register This register allows the user to invert the polarity of the Input Port register data. If a bit in this register is set (written with `1'), the corresponding Input Port data is inverted. If a bit in this register is cleared (written with a `0'), the Input Port data polarity is retained. Table 6. Register 2 - Polarity Inversion register bit description Legend: * default value. Bit Symbol Access Value Description 7 N7 R/W 0* inverts polarity of Input Port register data 6 N6 R/W 0* 0 = Input Port register data retained (default value) 5 N5 R/W 0* 1 = Input Port register data inverted 4 N4 R/W 0* 3 N3 R/W 0* 2 N2 R/W 0* 1 N1 R/W 0* 0 N0 R/W 0* PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 5 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 6.1.5 Register 3 - Configuration register This register configures the directions of the I/O pins. If a bit in this register is set, the corresponding port pin is enabled as an input with high-impedance output driver. If a bit in this register is cleared, the corresponding port pin is enabled as an output. At reset, the I/Os are configured as inputs. Table 7. Register 3 - Configuration register bit description Legend: * default value. Bit Symbol Access Value Description 7 C7 R/W 1* configures the directions of the I/O pins 6 C6 R/W 1* 0 = corresponding port pin enabled as an output 5 C5 R/W 1* 4 C4 R/W 1* 1 = corresponding port pin configured as input (default value) 3 C3 R/W 1* 2 C2 R/W 1* 1 C1 R/W 1* 0 C0 R/W 1* 6.2 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9534 in a reset condition until VDD has reached VPOR. At that point, the reset condition is released and the PCA9534 registers and state machine will initialize to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device. For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the operating voltage. 6.3 Interrupt output The open-drain interrupt output is activated when one of the port pins change state and the pin is configured as an input. The interrupt is deactivated when the input returns to its previous state or the Input Port register is read. Note that changing an I/O from and output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. 6.4 I/O port When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a high-impedance input. The input voltage may be raised above VDD to a maximum of 5.5 V. If the I/O is configured as an output, then either Q1 or Q2 is enabled, depending on the state of the Output Port register. Care should be exercised if an external voltage is applied to an I/O configured as an output because of the low-impedance paths that exist between the pin and either VDD or VSS. PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 6 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt data from shift register output port register data configuration register data from shift register D VDD Q1 Q FF write configuration pulse CK D Q Q FF IO0 to IO7 write pulse CK Q2 output port register VSS input port register D Q input port register data FF read pulse CK to INT polarity inversion register data from shift register D polarity inversion register data Q FF write polarity pulse CK 002aac470 Remark: At power-on reset, all registers return to default values. Fig 6. Simplified schematic of IO0 to IO7 6.5 Device address slave address 0 1 0 0 fixed A2 A1 A0 R/W hardware selectable 002aac471 Fig 7. PCA9534 device address 6.6 Bus transactions Data is transmitted to the PCA9534 registers using the Write mode as shown in Figure 8 and Figure 9. Data is read from the PCA9534 registers using the Read mode as shown in Figure 10 and Figure 11. These devices do not implement an auto-increment function, so once a command byte has been sent, the register which was addressed will continue to be accessed by reads until a new command byte has been sent. PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 7 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 0 1 0 command byte 0 A2 A1 A0 0 START condition A 0 0 0 0 0 0 data to port 0 1 A acknowledge from slave R/W acknowledge from slave A DATA 1 P STOP condition acknowledge from slave write to port tv(Q) data out from port data 1 valid 002aac472 Fig 8. Write to Output Port register SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 0 1 0 command byte 0 A2 A1 A0 0 START condition A 0 0 0 0 0 1 1/0 A acknowledge from slave R/W acknowledge from slave data to register 0 data to register A DATA P STOP condition acknowledge from slave 002aac473 Fig 9. Write to Configuration register or Polarity Inversion register slave address SDA S 0 1 0 0 A2 A1 A0 0 START condition A acknowledge from slave R/W acknowledge from slave data from register slave address (cont.) S 0 1 0 0 A2 A1 A0 1 (repeated) START condition (cont.) A command byte A R/W acknowledge from slave DATA (first byte) data from register A acknowledge from master DATA (last byte) NA no acknowledge from master at this moment master-transmitter becomes master-receiver and slave-receiver becomes slave-transmitter P STOP condition 002aac474 Fig 10. Read from register PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 8 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 0 1 0 data from port 0 A2 A1 A0 1 START condition DATA 1 A A DATA 2 tv(INT_N) NA P no acknowledge from master STOP condition tsu(D) th(D) data into port DATA 4 acknowledge from master R/W acknowledge from slave read from port data from port DATA 3 DATA 4 trst(INT_N) INT 002aac475 This figure assumes the command byte has previously been programmed with 00h. Transfer of data can be stopped at any moment by a STOP condition. Fig 11. Read Input Port register PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 9 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 7. Application design-in information 5V VDD (5 V) 10 k 10 k 10 k 2 k 10 k VDD 100 k (x 3) VDD MASTER CONTROLLER SCL SCL IO0 SUBSYSTEM 1 (e.g., temp. sensor) SDA SDA IO1 INT INT INT PCA9534 IO2 RESET IO3 SUBSYSTEM 2 (e.g., counter) IO4 VSS IO5 A IO6 IO7 A2 controlled switch (e.g., CBT device) enable A1 B A0 VSS ALARM SUBSYSTEM 3 (e.g., alarm system) VDD 002aac476 Device address configured as 0100 100X for this example. IO0, IO1, IO2 configured as outputs. IO3, IO4, IO5 configured as inputs. IO6, IO7 are not used and must be configured as outputs. Fig 12. Typical application 7.1 Minimizing IDD when the I/O us used to control LEDs When the I/Os are used to control LEDs, they are normally connected to VDD through a resistor as shown in Figure 12. Since the LED acts as a diode, when the LED is off the I/O VI is about 1.2 V less than VDD. The supply current, IDD, increases as VI becomes lower than VDD. Designs needing to minimize current consumption, such as battery power applications, should consider maintaining the IOn pins greater than or equal to VDD when the LED is off. Figure 13 shows a high value resistor in parallel with the LED. Figure 14 shows VDD less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O VI at or above VDD and prevents additional supply current consumption when the LED is off. PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 10 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 3.3 V VDD VDD VDD 100 k LED IOn 5V LED IOn 002aac660 002aac661 Fig 13. High value resistor in parallel with the LED Fig 14. Device supplied by a lower voltage 8. Limiting values Table 8. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD II Conditions Min Max Unit supply voltage -0.5 +6.0 V input current - 20 mA VI/O voltage on an input/output pin VSS - 0.5 5.5 V IO(IOn) output current on pin IOn - 50 mA IDD supply current - 85 mA ISS ground supply current - 100 mA Ptot total power dissipation - 200 mW Tstg storage temperature -65 +150 C Tamb ambient temperature -40 +85 C PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 11 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 9. Static characteristics Table 9. Static characteristics VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 2.3 - 5.5 V - 104 175 A - 0.25 1 A - 0.25 1 A - 1.5 1.65 V Supplies VDD supply voltage IDD supply current operating mode; VDD = 5.5 V; no load; fSCL = 100 kHz Istb standby current Standby mode; VDD = 5.5 V; no load; fSCL = 0 kHz; I/O = inputs VI = VSS VI = VDD VPOR power-on reset voltage no load; VI = VDD or VSS [1] Input SCL; input/output SDA VIL LOW-level input voltage -0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 5.5 V IOL LOW-level output current VOL = 0.4 V 3 6 - mA IL leakage current VI = VDD = VSS -1 - +1 A Ci input capacitance VI = VSS - 5 10 pF -0.5 - +0.8 V I/Os VIL LOW-level input voltage VIH HIGH-level input voltage IOL LOW-level output current VOH HIGH-level output voltage ILI input leakage current Ci input capacitance 2.0 - 5.5 V VOL = 0.5 V; VDD = 2.3 V [2] 8 10 - mA VOL = 0.7 V; VDD = 2.3 V [2] 10 13 - mA VOL = 0.5 V; VDD = 3.0 V [2] 8 14 - mA VOL = 0.7 V; VDD = 3.0 V [2] 10 19 - mA VOL = 0.5 V; VDD = 4.5 V [2] 8 17 - mA VOL = 0.7 V; VDD = 4.5 V [2] 10 24 - mA IOH = -8 mA; VDD = 2.3 V [3] 1.8 - - V IOH = -10 mA; VDD = 2.3 V [3] 1.7 - - V IOH = -8 mA; VDD = 3.0 V [3] 2.6 - - V IOH = -10 mA; VDD = 3.0 V [3] 2.5 - - V IOH = -8 mA; VDD = 4.75 V [3] 4.1 - - V IOH = -10 mA; VDD = 4.75 V [3] 4.0 - - V -1 - +1 A - 5 10 pF 3 - - mA VI = VDD = VSS Interrupt INT IOL LOW-level output current VOL = 0.4 V Select inputs A0, A1, A2 VIL LOW-level input voltage -0.5 - 0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V ILI input leakage current -1 - 1 A PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 12 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt [1] VDD must be lowered to 0.2 V in order to reset part. [2] Each I/O must be externally limited to a maximum of 25 mA and the device must be limited to a maximum current of 100 mA. [3] The total current sourced by all I/Os must be limited to 85 mA. 10. Dynamic characteristics Table 10. Dynamic characteristics Symbol Parameter Conditions Standard-mode I2C-bus Fast-mode I2C-bus Min Max Min Max 0 100 0 400 Unit fSCL SCL clock frequency kHz tBUF bus free time between a STOP and START condition 4.7 - 1.3 - s tHD;STA hold time (repeated) START condition 4.0 - 0.6 - s tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - s tSU;STO set-up time for STOP condition 4.0 - 0.6 - s tHD;DAT data hold time 0 - 0 - s data valid acknowledge time [1] 0.3 3.45 0.1 0.9 s tVD;DAT data valid time [2] 300 - 50 - ns tSU;DAT data set-up time 250 - 100 - ns tLOW LOW period of the SCL clock 4.7 - 1.3 - s tHIGH HIGH period of the SCL clock 4.0 - 0.6 tVD:ACK - s 0.1Cb[3] tr rise time of both SDA and SCL signals - 1000 20 + 300 ns tf fall time of both SDA and SCL signals - 300 20 + 0.1Cb[3] 300 s tSP pulse width of spikes that must be suppressed by the input filter - 50 - 50 ns tv(Q) data output valid time - 200 - 200 ns tsu(D) data input setup time 100 - 100 - ns th(D) data input hold time 1 - 1 - s Port timing Interrupt timing tv(INT_N) valid time on pin INT - 4 - 4 s trst(INT_N) reset time on pin INT - 4 - 4 s [1] tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA (out) LOW. [2] tVD;DAT = minimum time for SDA data output to be valid following SCL LOW. [3] Cb = total capacitance of one bus line in pF. PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 13 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt SDA tr tBUF tf tHD;STA tSP tLOW SCL tHD;STA P tSU;STA tHD;DAT S tHIGH tSU;DAT tSU;STO Sr P 002aaa986 Fig 15. Definition of timing protocol START condition (S) tSU;STA bit 7 MSB (A7) tLOW bit 6 (A6) tHIGH bit 0 (R/W) acknowledge (A) STOP condition (P) 1/f SCL SCL tBUF tr tf SDA tHD;STA tSU;DAT tHD;DAT tVD;DAT tVD;ACK tSU;STO 002aab175 Rise and fall times refer to VIL and VIH. Fig 16. I2C-bus timing diagram PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 14 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 11. Test information VDD PULSE GENERATOR VI RL 500 VO 6.0 V open VSS D.U.T. CL 50 pF RT 002aab393 RL = load resistor. CL = load capacitance includes jig and probe capacitance. RT = termination resistance should be equal to the output impedance Zo of the pulse generators. Fig 17. Test circuitry for switching times 500 from output under test CL 50 pF S1 2VDD open VSS 500 002aab881 Fig 18. Test circuit Table 11. Test tv(Q) Test data Load Switch CL RL 50 pF 500 PCA9534_3 Product data sheet 2VDD (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 15 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 12. Package outline SO16: plastic small outline package; 16 leads; body width 7.5 mm SOT162-1 D E A X c HE y v M A Z 16 9 Q A2 A (A 3) A1 pin 1 index Lp L 8 1 e detail X w M bp 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.3 0.1 2.45 2.25 0.25 0.49 0.36 0.32 0.23 10.5 10.1 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.01 0.019 0.013 0.014 0.009 0.41 0.40 0.30 0.29 0.05 0.419 0.043 0.055 0.394 0.016 inches 0.1 0.012 0.096 0.004 0.089 0.043 0.039 0.01 0.01 Z (1) 0.9 0.4 0.035 0.004 0.016 8o o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT162-1 075E03 MS-013 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 19. Package outline SOT162-1 (SO16) PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 16 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 E D A X c y HE v M A Z 9 16 Q (A 3) A2 A A1 pin 1 index Lp L 1 8 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.40 0.06 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC JEITA MO-153 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 20. Package outline SOT403-1 (TSSOP16) PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 17 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt HVQFN16: plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 4 x 4 x 0.85 mm A B D SOT629-1 terminal 1 index area A A 1 E c detail X e1 C 1/2 e e 8 y y1 C v M C A B w M C b 5 L 9 4 e e2 Eh 1/2 e 1 12 terminal 1 index area 16 13 X Dh 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. A1 b 1 0.05 0.00 0.38 0.23 c D (1) Dh E (1) Eh 0.2 4.1 3.9 2.25 1.95 4.1 3.9 2.25 1.95 e e1 0.65 1.95 e2 L v w y y1 1.95 0.75 0.50 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT629-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 21. Package outline SOT629-1 (HVQFN16) PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 18 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt HVQFN16: plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 3 x 3 x 0.85 mm A B D SOT758-1 terminal 1 index area A E A1 c detail X e1 C 1/2 e e 5 y y1 C v M C A B w M C b 8 L 4 9 e e2 Eh 1/2 e 12 1 16 terminal 1 index area 13 Dh X 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. A1 b 1 0.05 0.00 0.30 0.18 c D (1) Dh E (1) Eh 0.2 3.1 2.9 1.75 1.45 3.1 2.9 1.75 1.45 e e1 1.5 0.5 e2 L v w y y1 1.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT758-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 02-03-25 02-10-21 Fig 22. Package outline SOT758-1 (HVQFN16) PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 19 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 13. Handling information Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be completely safe you must take normal precautions appropriate to handling integrated circuits. 14. Soldering This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 14.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 14.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus PbSn soldering 14.3 Wave soldering Key characteristics in wave soldering are: PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 20 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities 14.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 23) than a PbSn process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 12 and 13 Table 12. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 13. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 23. PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 21 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 23. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". 15. Abbreviations Table 14. Abbreviations Acronym Description ACPI Advanced Configuration and Power Interface CDM Charged Device Model DUT Device Under Test ESD ElectroStatic Discharge FET Field-Effect Transistor GPIO General Purpose Input/Output HBM Human Body Model I2C-bus Inter-Integrated Circuit bus I/O Input/Output LED Light-Emitting Diode MM Machine Model POR Power-On Reset SMBus System Management Bus PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 22 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 16. Revision history Table 15. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9534_3 20061106 Product data sheet - PCA9534_2 Modifications: * The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. * * * * * * * * * * Legal texts have been adapted to the new company name where appropriate. * * pin names I/O0 through I/O7 changed to IO0 through IO7 added HVQFN16 (SOT758-1) package symbol (tpv and tPV) changed to tv(Q) symbol (tph and tPH) changed to th(D) symbol (tps and tPS) changed to tsu(D) symbol (tiv and tIV) changed to tv(INT_N) symbol (tir and tIR) changed to trst(INT_N) Figure 6 "Simplified schematic of IO0 to IO7": removed ESD diodes Table 8 "Limiting values": symbol "II/O, DC output current on an I/O" changed to "IO(IOn), output current on pin IOn" Table 9 "Static characteristics", sub-section "I/Os": symbol IIL changed to ILI added Section 15 "Abbreviations" PCA9534_2 (9397 750 13506) 20040930 Product data sheet - PCA9534_1 PCA9534_1 (9397 750 12454) 20031202 Product data ECN 853-2319 01-A14517 of 14 Nov 2003 - PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 23 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 17. Legal information 17.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 17.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 17.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 17.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 18. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com PCA9534_3 Product data sheet (c) NXP B.V. 2006. All rights reserved. Rev. 03 -- 6 November 2006 24 of 25 PCA9534 NXP Semiconductors 8-bit I2C-bus and SMBus low power I/O port with interrupt 19. Contents 1 2 3 4 5 5.1 5.2 6 6.1 6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 6.2 6.3 6.4 6.5 6.6 7 7.1 8 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 17 17.1 17.2 17.3 17.4 18 19 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Command byte . . . . . . . . . . . . . . . . . . . . . . . . . 4 Register 0 - Input Port register . . . . . . . . . . . . . 4 Register 1 - Output Port register. . . . . . . . . . . . 5 Register 2 - Polarity Inversion register . . . . . . . 5 Register 3 - Configuration register . . . . . . . . . . 6 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 6 Interrupt output . . . . . . . . . . . . . . . . . . . . . . . . . 6 I/O port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Device address . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . . 7 Application design-in information . . . . . . . . . 10 Minimizing IDD when the I/O us used to control LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 11 Static characteristics. . . . . . . . . . . . . . . . . . . . 12 Dynamic characteristics . . . . . . . . . . . . . . . . . 13 Test information . . . . . . . . . . . . . . . . . . . . . . . . 15 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Handling information. . . . . . . . . . . . . . . . . . . . 20 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Introduction to soldering . . . . . . . . . . . . . . . . . 20 Wave and reflow soldering . . . . . . . . . . . . . . . 20 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 20 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 21 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 23 Legal information. . . . . . . . . . . . . . . . . . . . . . . 24 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 24 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Contact information. . . . . . . . . . . . . . . . . . . . . 24 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2006. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 6 November 2006 Document identifier: PCA9534_3