Amplifier Built-in / U-shaped Micro Photoelectric Sensor Ultra-small / Cable type PM-25 SERIES Compact / Cable type PM-45 SERIES Compact / Connector built-in type PM-65 SERIES Conforming to EMC Directive PM-25 SERIES PM-45 SERIES PM-65 SERIES Ultimate U-shaped micro photoelectric sensors One Step Ahead in Performance and Mounting Ease 2015.12 panasonic.net/id/pidsx/global Certified (Some models only) Industry's First* and Industry's Top-in-Class* Advanced Sensors in the Industry. * Industry's first Three protection circuits standard on all models PM-25 SERIES PM-45 SERIES PM-65 SERIES All models are standardly equipped with the following protection circuits in their compact bodies. These protection circuits minimize the possibility of sensor malfunctions caused by erroneous wiring. 1 Reverse supply polarity protection circuit 6 mm 0.236 in 2 Reverse output polarity protection circuit 3 Output short-circuit protection circuit * Industry's first Industry's first! IP64 rating PM-25 SERIES PM-45 SERIES Our original integrated molding method has eliminated grooves and gaps on the sensing surface and main body, thus reducing the possibility of malfunctions caused by splashing water or dust. No ridges on sensing surface No joint seam * [Look!] Large and easy to see Multi-angle operation indicator Industry's top-in-class PM-25 SERIES PM-45 SERIES PM-65 SERIES The large operation indicator (orange) lights up when the beam enters. The indicator is easy to see from above and from the sides. PM-45 SERIES PM-65 SERIES The sensor unit can be installed with one or two M3 screws. Models requiring one M3 screw for installation PM-F25, PM-R25, PM-F65, PM-R65 Compact size Models requiring two M3 screws for installation Models other than above PM-45 SERIES All new models require significantly less mounting space than our conventional models when mounted with the same pitch. What's more, the new models can directly replace our conventional models currently in use. PM-L45 Conventional model (L type) 15.5 0.610 14.6 0.575 26 1.024 10 0.394 26 1.024 18.5 0.728 (Unit: mm in) 2 PM-25 SERIES * M3 screws and washers are not included. * Industry's top-in-class All models easy to mount with M3 screws Resistant to vibrations and impacts PM-25 SERIES PM-45 SERIES PM-65 SERIES The sections where stress concentrates, such as the connecting section of the cable and internal circuit, are covered with a resin. This helps prevent malfunctions caused by vibrations and Resin-filled structure impacts. (cross-sectional view) Translate to the Most * As of November 2015, according to our company's survey * Industry's first APPLICATIONS Ample beam emitting / receiving distance of 6 mm 0.236 in PM-25 SERIES PM-45 SERIES Positioning of a pallet PM-65 SERIES The beam emitting and receiving sections are 0.5 mm 0.02 in thinner than those on our conventional models while their external dimensions are the same. As a result, the distance between the beam emitting point and receiving point increased by 1 mm 0.039 in. The wider distance means less possibility of collision between the sensing section and sensing object. 13.4 0.528 6 0.236 Pallet is stopped by sensing the dog*. 3.7 0.146 Sensing the starting point and overrun of a moving body Overrun sensing Dog (Unit: mm in) * Starting point sensing Overrun sensing Beam marks for easy adjustment Industry's first PM-25 SERIES PM-45 SERIES Starting point and overrun is sensed using the dog* on the base. PM-65 SERIES The upper-limit and lower-limit positions of beam can be visually confirmed from the front, back, right and left sides of the sensor unit. This allows easy adjustment of the position of sensing object. Upper-limit position of beam axis Beam width Lower-limit position of beam axis Beam width marks are provided on PM25 series and PM45 series. Sensing the starting point on a rotating body Starting point The starting point can be sensed by making a slit in the rotating body. * "Dog" refers to the sensing object for activating the sensor's detecting operation. < Front / back > < Right / left > Sensors come in various shapes to suit a wide range of mounting conditions Ultra-small / Cable type PM-25 SERIES PM-K25 PM-U25 PM-L25 Compact / Cable type PM-K45 Compact / Connector built-in type PM-K65 PM-F25 PM-45 SERIES PM-T45 PM-L45 PM-T65W PM-R25 Compact size! PM-Y45 PM-65 SERIES PM-T65 Easy mounting with M2 / M3 screws! PM-F45 PM-R45 Easy connection with a single touch using commercially-available connectors PM-L65 PM-Y65 PM-F65 PM-F65W PM-R65 PM-R65W 3 PM -25 Ultra-small / Cable type PM-25 SERIES Cable type NPN output 1 m 3.281 ft cable 3 m 9.843 ft cable 1 m 3.281 ft bendingresistant cable Built-in connector PNP output 1 m 3.281 ft cable 3 m 9.843 ft cable 1 m 3.281 ft bendingresistant cable PM-K25 PM-L25 PM-U25 PM-F25 Easy mounting with M2 / M3 screws! PM-R25 Compact size! ORDER GUIDE U type R type F type Ultra-small / Cable type L type K type Type Appearance (mm in) 6 0.236 12.3 0.484 23.9 0.941 Sensing range 12 0.472 12 0.472 13.4 0.528 6 0.236 16 0.630 13.4 0.528 11.7 0.461 12.5 0.492 13.4 0.528 11.7 0.461 13.4 0.528 12.5 0.492 6 mm 0.236 in (fixed) Model No. Cable length Output Output operation PM-K25 1 m 3.281 ft PM-K25-R 1 m 3.281 ft, NPNcommercially-available open-collector using bending-resistant cable transistor PM-K25-C3 3 m 9.843 ft PM-K25-P 1 m 3.281 ft PM-L25 1 m 3.281 ft PM-L25-R 1 m 3.281 ft, bending-resistant cable PM-L25-C3 3 m 9.843 ft PM-L25-P 1 m 3.281 ft PM-U25 1 m 3.281 ft PM-U25-R 1 m 3.281 ft, bending-resistant cable PM-U25-C3 3 m 9.843 ft PM-U25-P 1 m 3.281 ft PM-F25 1 m 3.281 ft PM-F25-R 1 m 3.281 ft, bending-resistant cable PM-F25-C3 3 m 9.843 ft PM-F25-P 1 m 3.281 ft PM-R25 1 m 3.281 ft PM-R25-R 1 m 3.281 ft, bending-resistant cable PM-R25-C3 3 m 9.843 ft PM-R25-P 1 m 3.281 ft Easy connection with a single touch connectors PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor Incorporated with 2 outputs: Light-ON / Dark-ON PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor Note: The suffix "-R" in the model No. indicates a bending-resistant cable type. The suffix "-C3" indicates a 3 m 9.843 ft cable length type. OPTIONS 4 Designation Model No. Description Mounting screw MS-M2 Mounting screw with washers for the ultra-small type sensor (50 pcs. lot). It can mount securely as it is spring washer attached. Mounting screw ** MS-M2 M2 (length 10 mm 0.394 in) screw with a spring washer PM-25 SPECIFICATIONS Ultra-small / Cable type Model No. Type Item Bending-resistant cable 3 m 9.843 ft cable NPN output PM-25 PM-25-R PM-25-C3 PNP output PM-25-P Sensing range 6 mm 0.236 in (fixed) Minimum sensing object 0.8 x 1.2 mm 0.031 x 0.047 in opaque object Hysteresis 0.05 mm 0.002 in or less Repeatability 0.01 mm 0.0004 in or less Supply voltage 5 to 24 V DC 10 % Ripple P-P 10 % or less Current consumption 15 mA or less <NPN output type> NPN open-collector transistor ** Maximum sink current: 50 mA ** Applied voltage: 30 V DC or less (between output and 0 V) ** Residual voltage: 2 V or less (at 50 mA sink current) 1 V or less (at 16 mA sink current) Output Output operation Incorporated with 2 outputs: Light-ON / Dark-ON Short-circuit protection Incorporated Under light received condition: 20 s or less Under light interrupted condition: 80 s or less (Maximum response frequency: 3 kHz) (Note 2) Response time Operation indicator Orange LED (lights up under light received condition) Pollution degree 3 Protection Environmental resistance <PNP output type> PNP open-collector transistor ** Maximum source current: 50 mA ** Applied voltage: 30 V DC or less (between output and + V) ** Residual voltage: 2 V or less (at 50 mA source current) 1 V or less (at 16 mA source current) IP64 (IEC) Ambient temperature (Note 3, 4) -25 to +55 C -13 to +131 F (No dew condensation or icing allowed), Storage: -30 to +80 C -22 to +176 F Ambient humidity 5 to 85 % RH, Storage: 5 to 95 % RH Ambient illuminance Fluorescent light: 1,000 x at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 M, or more, with 250 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each 15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each Shock resistance Emitting element Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated) Material Enclosure: PBT, Display section: Polycarbonate 0.09-mm2 4-core cabtyre cable, PVC, 1 m 3.281 ft long Cable 0.1-mm2 4-core bending-resistant cabtyre cable, PVC, 1 m 3.281 ft long (Note 5, 6) 0.09-mm2 4-core cabtyre cable, PVC, 3 m 9.843 ft long Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 7) Cable extension Weight Net weight: 10 g approx., Gross weight: 15 g approx. Net weight: 30 g approx., Gross weight: 35 g approx. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 C +73.4 F. 2) The response frequency is the value when the disc, given in the figure below, is rotated. Disc 1.8 mm 0.071 in Disc t = 0.2 mm 0.008 in 1.6 mm 0.063 in 1.6 mm 0.063 in 3) In case the PM-25 series is used at an ambient temperature of +50 C +122 F, or more, make sure to mount it on a metal body. 4) Note that the cable of PM-25-R loses its flexibility when the ambient temperature decreases to about -10 C +14 F. 5) The cable of PM-25-R is a bending-resistant cable usable on a moving base. When the sensor is mounted on a moving base, secure the sensor cable joint at the unit in place so that stress is not applied to it. 6) When storing PM-25-R, make sure that the cable does not come into contact with the sensing section or operation indicator. 7) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher. 5 PM -45 Compact / Cable type PM-45 SERIES Cable type NPN output 1 m 3.281 ft cable 3 m 9.843 ft cable 1 m 3.281 ft bendingresistant cable Built-in connector PNP output 1 m 3.281 ft cable 3 m 9.843 ft cable 1 m 3.281 ft bendingresistant cable Easy mounting with M2 / M3 screws! Compact size! PM-K45 PM-T45 PM-L45 PM-Y45 PM-F45 PM-R45 Easy connection with a single touch using commercially-available connectors ORDER GUIDE Appearance (mm in) 25.4 1.000 21.3 0.839 13.7 0.539 L type 26 1.024 18.1 0.713 14.6 0.575 26 1.024 7 0.276 6 mm 0.236 in (fixed) 14.6 0.575 Y type Compact / Cable type Sensing range 7 0.276 T type K type Type R type F type 13.4 0.528 20.6 0.811 13 0.512 13.7 0.539 21.3 0.839 13 0.512 13.7 0.539 21.3 0.839 Model No. PM-K45 1 m 3.281 ft PM-K45-C3 3 m 9.843 ft PM-K45-P 1 m 3.281 ft PM-K45-P-C3 3 m 9.843 ft PM-T45 1 m 3.281 ft PM-T45-C3 3 m 9.843 ft PM-T45-P 1 m 3.281 ft PM-T45-P-C3 3 m 9.843 ft PM-L45 1 m 3.281 ft PM-L45-C3 3 m 9.843 ft PM-L45-P 1 m 3.281 ft PM-L45-P-C3 3 m 9.843 ft PM-Y45 1 m 3.281 ft PM-Y45-C3 3 m 9.843 ft PM-Y45-P 1 m 3.281 ft PM-Y45-P-C3 3 m 9.843 ft PM-F45 1 m 3.281 ft PM-F45-C3 3 m 9.843 ft PM-F45-P 1 m 3.281 ft PM-F45-P-C3 3 m 9.843 ft PM-R45 1 m 3.281 ft PM-R45-C3 3 m 9.843 ft PM-R45-P 1 m 3.281 ft PM-R45-P-C3 3 m 9.843 ft Note: The suffix "-C3" in the model No. indicates a 3 m 9.843 ft cable length type. 6 Cable length Output Output operation NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor Incorporated with 2 outputs: Light-ON / Dark-ON PM-45 SPECIFICATIONS Compact / Cable type Model No. Type Item 3 m 9.843 ft cable NPN output PM-45 PM-45-C3 PNP output PM-45-P PM-45-P-C3 Sensing range 6 mm 0.236 in (fixed) Minimum sensing object 0.8 x 1.2 mm 0.031 x 0.047 in opaque object Hysteresis 0.05 mm 0.002 in or less Repeatability 0.01 mm 0.0004 in or less Supply voltage 5 to 24 V DC 10 % Ripple P-P 10 % or less Current consumption 15 mA or less <NPN output type> NPN open-collector transistor ** Maximum sink current: 50 mA ** Applied voltage: 30 V DC or less (between output and 0 V) ** Residual voltage: 2 V or less (at 50 mA sink current) 1 V or less (at 16 mA sink current) Output Output operation Incorporated with 2 outputs: Light-ON / Dark-ON Short-circuit protection Incorporated Under light received condition: 20 s or less Under light interrupted condition: 80 s or less (Maximum response frequency: 3 kHz) (Note 2) Response time Operation indicator Orange LED (lights up under light received condition) Pollution degree 3 Protection Environmental resistance <PNP output type> PNP open-collector transistor ** Maximum source current: 50 mA ** Applied voltage: 30 V DC or less (between output and + V) ** Residual voltage: 2 V or less (at 50 mA source current) 1 V or less (at 16 mA source current) IP64 (IEC) Ambient temperature -25 to +55 C -13 to +131 F (No dew condensation or icing allowed), Storage: -30 to +80 C -22 to +176 F Ambient humidity 5 to 85 % RH, Storage: 5 to 95 % RH Ambient illuminance Fluorescent light: 1,000 x at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 M, or more, with 250 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each 15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each Shock resistance Emitting element Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated) Material Enclosure: PBT, Display section: Polycarbonate 2 0.09-mm 4-core cabtyre cable, PVC, 1 m 3.281 ft long Cable 0.09-mm2 4-core cabtyre cable, PVC, 3 m 9.843 ft long Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 3) Cable extension Weight Net weight: 10 g approx., Gross weight: 15 g approx. Net weight: 30 g approx., Gross weight: 35 g approx. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 C +73.4 F. 2) The response frequency is the value when the disc, given in the figure below, is rotated. Disc Disc 1.8 mm 0.071 in t = 0.2 mm 0.008 in 1.6 mm 0.063 in 1.6 mm 0.063 in 3) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher. 7 Compact size! PM -65 Compact / Connector built-in type Cable type NPN output Connector attached cable 1 m 3.281 ft, 2 m 6.562 ft, 3 m 9.843 ft, 5 m 16.404 ft Connector attached bending-resistant cable 1 m 3.281 ft, 2 m 6.562 ft, 3 m 9.843 ft, 5 m 16.404 ft PNP output Connector attached cable 1 m 3.281 ft, 2 m 6.562 ft, 3 m 9.843 ft, 5 m 16.404 ft Connector attached bending-resistant cable 1 m 3.281 ft, 2 m 6.562 ft, 3 m 9.843 ft, 5 m 16.404 ft Built-in connector PM-K65 PM-65 SERIES PM-T65 PM-T65W PM-L65 PM-Y65 Easy connection with a single touch using commercially-available connectors PM-F65 PM-F65W PM-R65 PM-R65W ORDER GUIDE K type Type Appearance (mm in) 22.4 0.882 26 1.024 Sensing range T type 22.4 0.882 22.4 0.882 16.7 0.657 L type NPN open-collector transistor PM-K65-P PNP open-collector transistor PM-T65 NPN open-collector transistor PM-T65-P PNP open-collector transistor PM-T65W NPN open-collector transistor PM-T65W-P PNP open-collector transistor PM-L65 NPN open-collector transistor PM-L65-P PNP open-collector transistor PM-Y65 NPN open-collector transistor PM-Y65-P PNP open-collector transistor PM-F65 NPN open-collector transistor PM-F65-P PNP open-collector transistor PM-F65W NPN open-collector transistor PM-F65W-P PNP open-collector transistor PM-R65 NPN open-collector transistor PM-R65-P PNP open-collector transistor PM-R65W NPN open-collector transistor PM-R65W-P PNP open-collector transistor 14.9 0.587 26.2 1.031 15.7 0.618 Y type 14.9 0.587 6 mm 0.236 in (fixed) 13.4 0.528 13.5 0.531 F type Compact / Connector built-in type 26 1.024 Output PM-K65 7 0.276 13.7 0.539 26 1.024 Model No. 13.4 0.528 22.7 0.894 22.4 0.882 Output operation Incorporated with 2 outputs: Light-ON / Dark-ON 13 0.512 13.4 0.528 22.4 0.882 R type 13.5 0.531 13.4 0.528 22.4 0.882 13 0.512 13.4 0.528 22.4 0.882 Note: "W" in the model No. indicates that the product is mounting-compatible with our conventional models [PM-T53(B) / PM-64(P)]. 8 PM-65 OPTIONS Designation Model No. Connector attached cable Connector attached cable Bendingresistant cable CN-14A-C1 Length: 1m 3.281 ft CN-14A-C2 Length: 2m 6.562 ft CN-14A-C3 Length: 3m 9.843 ft CN-14A-C5 Length: 5m 16.404 ft CN-14A-R-C1 Length: 1m 3.281 ft CN-14A-R-C2 Length: 2m 6.562 ft CN-14A-R-C3 Length: 3m 9.843 ft CN-14A-R-C5 Length: 5m 16.404 ft CN-14A Connector Connector attached cable Description ** CN-14A(-R)-C 0.2 mm2 4-core cabtyre cable with connector on one end Cable outer diameter: o3.7 mm o0.146 in 0.2 mm2 4-core cabtyre cable with connector on one end Cable outer diameter: o3.7 mm o0.146 in Connector ** CN-14A Contact 4 Set of 10 housings and 40 contacts Housing SPECIFICATIONS Compact / Connector built-in type Model No. Type Item Mounting-compatible with conventional model (Note 2) NPN output PM-65 PM-65W PNP output PM-65-P PM-65W-P Sensing range 6 mm 0.236 in (fixed) Minimum sensing object 0.8 x 1.2 mm 0.031 x 0.047 in opaque object Hysteresis 0.05 mm 0.002 in or less Repeatability 0.01 mm 0.0004 in or less Supply voltage 5 to 24 V DC 10 % Ripple P-P 10 % or less Current consumption Output 15 mA or less <NPN output type> NPN open-collector transistor ** Maximum sink current: 50 mA ** Applied voltage: 30 V DC or less (between output and 0 V) ** Residual voltage: 2 V or less (at 50 mA sink current) 1 V or less (at 16 mA sink current) Output operation Incorporated with 2 outputs: Light-ON / Dark-ON Short-circuit protection Response time Incorporated Under light received condition: 20 s or less, Under light interrupted condition: 80 s or less (Maximum response frequency: 3 kHz) (Note 3) Operation indicator Orange LED (lights up under light received condition) Pollution degree 3 Protection Environmental resistance <PNP output type> PNP open-collector transistor ** Maximum source current: 50 mA ** Applied voltage: 30 V DC or less (between output and + V) ** Residual voltage: 2 V or less (at 50 mA source current) 1 V or less (at 16 mA source current) IP40 (IEC) Ambient temperature -25 to +55 C -13 to +131 F (No dew condensation or icing allowed), Storage: -30 to +80 C -22 to +176 F Ambient humidity 5 to 85 % RH, Storage: 5 to 95 % RH Ambient illuminance Fluorescent light: 1,000 x at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 M, or more, with 250 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 2,000 Hz frequency, 1.5 mm 0.059 in double amplitude (maximum acceleration 196 m/s2) in X, Y and Z directions for two hours each 15,000 m/s2 acceleration (1,500 G approx.) in X, Y and Z directions three times each Shock resistance Emitting element Infrared LED (Peak emission wavelength: 855 nm 0.034 mil, non-modulated) Material Enclosure: PBT, Display section: Polycarbonate Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. (Note 4) Cable length Weight Net weight: 3 g approx., Gross weight: 3 g approx. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 C +73.4 F. 2) Mounting-compatible with our conventional models [PM-T53(B) / PM-64(P)] 3) The response frequency is the value when the disc, given in the figure below, is rotated. Disc 1.8 mm 0.071 in Disc Recommended connector Contact: SPHD-001T-P0.5, Housing: PAP-04V-S (Manufactured by J.S.T. Mfg. Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. Recommended crimping tool Model No. : YC-610R (Manufactured by J.S.T. Mfg. Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. t = 0.2 mm 0.008 in 1.6 mm 0.063 in 1.6 mm 0.063 in 4) If the cable is extended to 20 m 65.617 ft or longer, confirm that the supply voltage at the end of the cable attached to the sensor is 4.5 V or higher. 9 PM-25 PM-45 PM-65 I/O CIRCUIT AND WIRING DIAGRAMS NPN output type I/O circuit diagram Wiring diagram (PM-25 series / PM-45 series) Color of cable type lead wire or color of lead wire of connector attached cable Brown Load Black (Note) Sensor circuit (Brown) +V ZD1 ZD2 Tr2 (Black) Output 1 (Note) Load 50 mA max. (White) Output 2 (Note) T r1 D (Blue) 0 V Load + - Load 50 mA max. + - White (Note) 5 to 24 V DC 10 % 5 to 24 V DC 10 % Blue Note: Ensure to insulate the unused output wire. Internal circuit Users' circuit Output operation Note: Ensure to insulate the unused output wire. Symbols...D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2: NPN output transistor Color code Output operation Output 1 Black Light-ON Output 2 White Dark-ON Terminal arrangement diagram (PM-65 series) 1 2 3 4 Terminal No. Designation 1 +V 2 Output 1: Light-ON 3 Output 2: Dark-ON 4 0V PNP output type Wiring diagram (PM-25 series / PM-45 series) I/O circuit diagram Color of cable type lead wire or color of lead wire of connector attached cable Sensor circuit D (Brown) +V Tr1 Tr2 ZD1 ZD2 Brown Black (Note) + 50 mA max. (Black) Output 1 (Note) 50 mA max. (White) Output 2 (Note) Load (Blue) 0 V + Load - White (Note) 5 to 24 V DC 10 % Load - 5 to 24 V DC 10 % Load Blue Note: Ensure to insulate the unused output wire. Internal circuit Users' circuit Note: Ensure to insulate the unused output wire. Symbols...D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2: PNP output transistor Output operation Color code Output operation Output 1 Black Light-ON Output 2 White Dark-ON Terminal arrangement diagram (PM-65 series) 1 10 2 3 4 Terminal No. Designation 1 +V 2 Output 1: Light-ON 3 Output 2: Dark-ON 4 0V PM-25 PM-45 PM-65 SENSING CHARACTERISTICS (TYPICAL) PM-25 series PM-45 series Sensing position Sensing position DarkON DarkON DarkON 5.5 mm 0.217 in DarkON 8.4 mm 0.331 in 6 mm 0.236 in Beam axis 0 2 mm 0.079 in 2 mm 0.079 in LightON 7 mm 0.276 in 1 2 3 0.039 0.079 0.118 Operating point (mm in) 4 0.157 LightON 0 1 2 3 0.039 0.079 0.118 Operating point (mm in) 4 0.157 LightON Beam axis 0 1 2 3 0.039 0.079 0.118 Operating point (mm in) 4 0.157 LightON 0 1 2 3 0.039 0.079 0.118 Operating point (mm in) 4 0.157 PM-65 series Sensing position DarkON DarkON 8.4 mm 0.331 in 7 mm 0.276 in 2 mm 0.079 in LightON Beam axis 0 1 2 3 0.039 0.079 0.118 Operating point (mm in) 4 0.157 LightON 0 1 2 3 0.039 0.079 0.118 Operating point (mm in) 4 0.157 PRECAUTIONS FOR PROPER USE **Never use this product as a sensing device for personnel protection. **In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. PM-45 series **The following conditions must be observed when using screws to mount the sensor unit. Screw M3 screw Spring washer Flat washer Tightening torque 1 pc. o6 mm o0.236 in (small round washer) 0.5 N*m M3 screws Spring washer Mounting Plain washer Outer diameter o6 mm o0.236 in PM-25 series **The following conditions must be observed when using screws to mount the sensor unit. Screw M2 screw M3 screw Spring washer Flat washer Tightening torque 1 pc. o4.3 mm o0.169 in (small round washer) 0.15 N*m 1 pc. o6 mm o0.236 in (small round washer) 0.5 N*m < When using M2 screws for mounting > < When using M3 screws for mounting > M2 screws Spring washer Plain washer Outer diameter o4.3 mm o0.169 in M3 screws Spring washer Plain washer Outer diameter o6 mm o0.236 in When using the optional mounting screw set MS-M2, a spring washer is included. **In case the PM-25 series is used at an ambient temperature of +50 C +122 F, or more, make sure to mount it on a metal body. PM-65 series **The following conditions must be observed when using screws to mount the sensor unit. Screw M3 screw Spring washer Flat washer Tightening torque 1 pc. o6 mm o0.236 in (small round washer) 0.5 N*m M3 screws Spring washer Plain washer Outer diameter o6 mm o0.236 in 11 PM-25 PM-45 PM-65 PRECAUTIONS FOR PROPER USE Cable extension Wiring (PM-65 series) PM-25 series / PM-45 series **Cable extension is possible up to an overall length of 100 m 328.084 ft with a 0.3 mm2, or more, cable. However, since a voltage drop shall occur due to the cable extension, ensure that the power supply voltage at the end of the cable attached to the sensor is within the rating. Connection method **Insert the connector attached cable CN14A-C / CN14A-R-C in the connector part of this product as shown in the figure below. Lock release lever Total cable length 100 m 328.084 ft CN-14A-C / CN-14A-R-C Cable attached to sensor +V Extension cable Output + 5 to 24 V DC 10 % - 0V <Connector> Housing: PAP-04V-S (Manufactured by J.S.T. Mfg. Co., Ltd.) <Connector pin position> Supply voltage: 4.5 V or more But, when the overall cable length, including the cable attached to the sensor, is as given below, there is no need to confirm the voltage. Conductor crosssection area of extension cable 0.08 to 0.1 mm2 Total cable length Up to 5 m 16.404 ft 2 0.2 mm Up to 10 m 32.808 ft 0.3 mm2 Up to 20 m 65.617 ft Output + 0V - 5 to 24 V DC 10 % Supply voltage: 4.5 V or more But, when the overall cable length, including the cable attached to the sensor, is as given below, there is no need to confirm the voltage. Conductor crosssection area of extension cable 0.08 to 0.1 mm2 12 Total cable length Up to 5 m 16.404 ft 2 0.2 mm Up to 10 m 32.808 ft 0.3 mm2 Up to 20 m 65.617 ft +V Output 1 Output 2 0V Disconnection method **Press and hold the lock release lever to disconnect the cable connector. Note: Pulling the cable without pressing the lock release lever in an attempt to disconnect the connector can cause wire breakage in the cable or damage to the connector. PM-65 series **Cable extension is possible up to an overall length of 100 m 328.084 ft with a 0.3 mm2, or more, cable. However, since a voltage drop shall occur due to the cable extension, ensure that the power supply voltage at the end of the connector attached cable of the sensor or at the sensor terminals is within the rating. Total cable length 100 m 328.084 ft Connector +V attached cable Extension cable Connector pin No. Terminal designation When using the product as an S-mark compatible product in Korea **The power supply cable and output cable connected to the product must be less than 10 m 32.808 ft. Other **This device has been developed / produced for industrial use only. **Since the sensor is intended for use inside machines, no special countermeasures have been taken against extraneous light. Take care that extraneous light is not directly incident on the beam receiving section. **Do not use during the initial transient time (50 ms) after the power supply is switched on. **Note that the cable of PM-25-R loses its flexibility when the ambient temperature decreases to about -10 C +14 F. **The cable of PM-25-R is a bending-resistant cable usable on a moving base. When the sensor is mounted on a moving base, secure the sensor cable joint at the unit in place so that stress is not applied to it. **When storing PM-25-R, make sure that the cable does not come into contact with the sensing section or operation indicator. **If the sensor is used in a place having excessive dust, periodically clean the emitting and receiving sections with a dry, soft cloth. **If there is a large surge generating equipment, such as, motor, solenoid, electromagnetic valve, etc., in the vicinity of the sensor, use a surge absorber on that equipment. Further, do not run the sensor cables along power lines and use a capacitor between +V and 0 V, if required. Use the sensor after confirming that the surge has been eliminated. PM-25 PM-45 PM-65 DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. PM-K25 Sensor Operation indicator (Orange) 23.9 0.941 18.7 0.736 13.4 0.528 6 0.236 1.7 0.067 1.75 0.069 2-elongated mounting holes Beam axis 12 6 0.472 0.236 Operation indicator (Orange) 8 0.315 6 0.236 2 0.079 5.5 Beam 12.3 0.217 axis 0.484 5.5 Beam 0.217 axis 5 0.197 2-o3.2 o0.126 mounting holes o6 o0.236 13.4 0.528 6 0.236 Beam size: 1.2 x 0.8 0.047 x 0.031 8 0.315 Sensor Operation indicator (Orange) 3 0.118 3 0.118 6 Beam 0.236 axis PM-L25 1.6 0.063 3.2 0.126 Operation indicator (Orange) 2 0.079 6 0.236 Beam size: 1.2 x 0.8 0.047 x 0.031 10 12 0.394 0.472 4 0.157 o2.5 o0.098 cable, 1 m 3.281 ft long 2 0.079 o2.5 o0.098 cable, 1 m 3.281 ft long PM-K25(-P) PM-L25(-P) PM-U25 Sensor PM-F25 Sensor Operation indicator (Orange) 6 3 0.118 0.236 6 Beam 0.236 axis Beam axis 13.4 0.528 6 0.236 Operation indicator (Orange) 2 0.079 5.5 Beam 0.217 axis 11.5 0.453 16 0.630 2-o3.2 o0.126 mounting holes Operation indicator (Orange) Beam size: 1.2 x 0.8 0.047 x 0.031 3 0.118 11.7 0.461 6.2 0.244 1.6 0.063 Elongated mounting hole 1.95 0.077 8 0.315 PM-U25(-P) 12.5 12 8 0.315 0.492 0.472 5 3.2 0.126 0.197 o2 o0.079 o2.5 o0.098 cable, 1 m 3.281 ft long Beam size: 1.2 x 0.8 0.047 x 0.031 1.5 0.059 (2 0.079) R1.6 R0.063 o2.5 o0.098 cable, 1 m 3.281 ft long 4 0.157 6.7 0.264 13.4 0.528 6 0.236 Operation indicator (Orange) Beam 5.5 axis 0.217 2 0.079 o4.8 o0.189 PM-F25(-P) PM-R25 Sensor Beam 6 axis 0.236 Operation indicator (Orange) 4 0.157 6.7 0.264 Operation indicator (Orange) 5.5 Beam 0.217 axis 2 0.079 13.4 0.528 6 0.236 Beam size: 1.5 0.059 1.2 x 0.8 0.047 x 0.031 R1.6 (2 0.079) R0.063 12 8 0.315 0.472 12.5 0.492 o2.5 o0.098 cable, 1 m 3.281 ft long o4.8 o0.189 5 3.2 Elongated mounting hole 1.6 0.063 11.7 0.461 6.2 0.244 3 0.118 o2 o0.079 1.95 0.077 PM-R25(-P) 13 PM-25 PM-45 PM-65 DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. PM-K45 Sensor 25.4 1.000 19 0.748 PM-T45 Sensor Operation indicator (Orange) 3.5 0.138 7 0.276 Operation indicator (Orange) 2-o3.2 o0.126 mounting holes 19 0.748 13.4 0.528 6 0.236 Operation indicator (Orange) 2-o3.8 o0.150 mounting holes 26 1.024 6 Beam size: 1.2 x 0.8 0.047 x 0.031 0.236 2 0.079 19 0.748 6 0.236 8.4 0.331 3.2 0.126 Operation indicator (R) (Orange) 4.3 0.169 o2.5 o0.098 cable, 1 m 3.281 ft long 0.244 5.5 0.217 13.7 0.539 13.4 0.528 2 0.079 Beam axis 15.2 0.598 13 17.2 18.1 0.677 0.512 0.713 6.2 Beam axis 13.8 0.543 8.4 0.331 17.2 21.3 0.677 0.839 11 0.433 Beam size: 1.2 x 0.8 0.047 x 0.031 2-elongated mounting holes o2.5 o0.098 cable, 1 m 3.281 ft long 2.5 0.098 PM-T45 PM-K45 PM-L45 Sensor 26 1.024 3.5 0.138 10 7 0.276 3.2 0.126 0.394 Sensor 3.5 0.138 Operation indicator (Orange) 19 0.748 7 0.276 7.5 0.295 7 0.276 Operation indicator (Orange) o2.5 o0.098 cable, 1 m 3.281 ft long 5 0.197 o2.5 o0.098 cable, 1 m 3.281 ft long 1.5 0.059 19 0.748 13.4 0.528 6 0.236 2-o3.2 o0.126 mounting holes 14.6 0.575 Operation indicator (Orange) 6 2 Beam size: 0.079 1.2 x 0.8 0.047 x 0.031 0.236 Beam axis 9 0.354 12.6 0.496 8.4 0.331 7.2 0.283 2-o3.5 o0.138 mounting holes 20.6 6 0.811 0.236 2-elongated mounting holes 4 0.157 PM-Y45 4.5 0.177 13.4 0.528 6 0.236 14.6 0.575 2 0.079 8.4 0.331 Beam size: 1.2 x 0.8 0.047 x 0.031 2 0.079 Beam axis 12.6 0.496 4.5 0.177 2.5 0.098 Operation indicator (Orange) 2 0.079 PM-L45 PM-F45 Sensor PM-R45 Sensor PM-Y45 Operation indicator (Orange) Operation indicator (Orange) 8.4 0.331 13.6 0.535 2.5 0.098 13.7 0.539 13.4 0.528 6 0.236 Beam size: 1.2 x 0.8 0.047 x 0.031 2 0.079 Beam axis 15.2 0.598 9 0.354 7 0.276 2-o3.5 o0.138 mounting holes o2.5 o0.098 cable, 1 m 3.281 ft long Operation indicator (Orange) 13 0.512 7 0.276 6 0.236 17.2 0.677 21.3 0.839 Beam size: 1.2 x 0.8 0.047 x 0.031 6 0.236 17.2 21.3 0.677 0.839 13 0.512 7 0.276 13.7 2 0.079 9 0.354 7 0.276 Beam axis 15.2 0.598 2-o3.5 o0.138 mounting holes o2.5 o0.098 cable, 1 m 3.281 ft long PM-R45 PM-F45 14 13.4 6 Operation indicator (Orange) 8.4 0.331 13.6 0.535 2.5 0.098 PM-25 PM-45 PM-65 DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. PM-K65PM-K65-P Sensor PM-T65PM-T65-P Sensor Operation indicator (Orange) 26 1.024 20 0.787 6.5 0.256 Beam size: 1.2 x 0.8 0.047 x 0.031 26 1.024 20 0.787 6 7 0.276 0.236 Beam axis 4.1 0.161 2 0.079 Beam 8.4 0.331 axis 22.4 3.2 0.126 0.882 7.4 0.291 Operation indicator (Orange) 22.4 0.882 13.8 0.543 8.3 0.327 3.7 0.146 8.4 0.331 Operation indicator (Orange) 7 0.276 Beam axis Sensor 4.1 0.161 1.6 0.063 26 1.024 20 0.787 6.5 0.256 PM-L65PM-L65-P 13 0.512 Beam size: 1.2 x 0.8 0.047 x 0.031 6 0.236 26.2 1.031 20 0.787 3.9 0.154 1.7 0.067 Beam axis 4 0.157 Beam axis Operation indicator (Orange) 10 0.394 Beam axis 2-mounting holes 14.9 0.587 Sensor 13.4 0.528 6 0.236 8.4 0.331 6.5 0.256 Beam axis 9 0.354 12.9 0.508 Operation indicator (Orange) 7.2 0.283 20 0.787 Operation indicator (Orange) PM-T65W(-P) Beam size: 1.2 x 0.8 0.047 x 0.031 7 6 15.7 0.276 0.236 0.618 3.2 0.126 (2 0.079) 6 13.4 0.236 0.528 Sensor Operation indicator (Orange) 2-elongated mounting holes 7.4 0.291 6 0.236 (2 0.079) 3 0.118 PM-T65(-P) PM-T65WPM-T65W-P PM-Y65PM-Y65-P Beam axis 2 0.079 13.4 0.528 PM-K65(-P) 7.4 0.291 14 0.551 Beam size: 1.2 x 0.8 0.047 x 0.031 6 0.236 Operation indicator (Orange) 13.7 0.539 2-mounting holes 2 0.079 3.7 0.146 20 0.787 2.3 0.091 13 0.512 1.6 0.063 13.4 0.528 6 0.236 16.7 0.657 7.4 0.291 6.2 3.2 0.126 0.244 3.5 0.138 2-o3.2 o0.126 mounting holes 22.4 0.882 8.4 8.3 0.331 0.327 2-elongated mounting holes 2-o3.2 o0.126 mounting holes 26.2 1.031 PM-F65PM-F65-P Operation indicator (Orange) 2-o3.5 o0.138 mounting holes 7 0.276 Operation indicator (Orange) 6.5 0.256 6 0.236 2.5 0.098 3.5 0.138 7 0.276 22.7 Beam 0.894 axis 6 0.236 3 0.118 Beam size: 1.2 x 0.8 0.047 x 0.031 Beam 14.9 8.4 0.331 axis 0.587 2 0.079 6.5 0.256 o2.4 o0.094 16.3 0.642 Beam axis 8.3 7.7 0.303 0.327 4.1 0.161 PM-Y65(-P) 2.5 0.098 Beam size: 1.2 x 0.8 0.047 x 0.031 13.4 0.528 6 (2 0.079) 0.236 8.4 3.2 0.331 0.126 3.7 2.1 22.4 0.146 0.083 0.882 Operation indicator (Orange) 12.9 0.508 Beam axis 3 0.118 Operation indicator (Orange) 13.4 0.528 6 0.236 Sensor PM-L65(-P) 7 0.276 13.5 0.531 Elongated mounting hole PM-F65(-P) 15 PM-25 PM-45 PM-65 DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. PM-F65WPM-F65W-P 13.7 0.539 7 0.276 Sensor Beam axis 3 0.118 6 6.5 0.236 0.256 Beam axis 13 0.512 7 0.276 Beam size: 1.2 x 0.8 0.047 x 0.031 13.4 0.528 6 0.236 Sensor Operation indicator (Orange) Operation indicator (Orange) Beam axis 2.5 0.098 PM-R65PM-R65-P Operation indicator (Orange) 6 0.236 (2 0.079) 2-o3.5 o0.138 mounting holes 22.4 0.882 8.3 0.327 3 0.118 Beam size: 1.2 x 0.8 0.047 x 0.031 6.5 0.256 (2 0.079) 9 0.354 13.6 7 0.535 0.276 13.4 0.528 6 0.236 Beam axis 11.4 0.449 Operation indicator (Orange) o2.4 o0.094 2.5 0.098 8.4 0.331 22.4 0.882 3.2 0.126 16.3 0.642 3.7 0.146 8.3 0.327 7.7 0.303 2.1 0.083 PM-F65W(-P) 4.1 0.161 7 0.276 13.5 0.531 Elongated mounting hole PM-R65(-P) PM-R65WPM-R65W-P Sensor Operation indicator (Orange) 6.5 0.256 6 0.236 (2 0.079) 13 0.512 7 0.276 L 13.7 0.539 7 0.276 35 1.378 Beam size: 1.2 x 0.8 0.047 x 0.031 Operation indicator (Orange) 2-o3.5 o0.138 mounting holes 7 0.276 13.6 0.535 13.4 0.528 6 0.236 50 1.969 8 0.315 8 0.315 Beam axis 9 0.354 11.4 0.449 CN-14A-C CN-14A-R-C Connector attached cable (Optional) 2.5 0.098 o3.7 o0.146 cable Beam axis ** Length L 22.4 0.882 8.3 0.327 Model No. Length L CN-14A(-R)-C1 1,000 39.370 CN-14A(-R)-C2 2,000 78.740 CN-14A(-R)-C3 3,000 118.110 CN-14A(-R)-C5 5,000 196.850 PM-R65W(-P) Disclaimer The applications described in the catalog are all intended for examples only. The purchase of our products described in the catalog shall not be regarded as granting of a license to use our products in the described applications. We do NOT warrant that we have obtained some intellectual properties, such as patent rights, with respect to such applications, or that the described applications may not infringe any intellectual property rights, such as patent rights, of a third party. Please contact: 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Global Sales Department Telephone: +81-568-33-7861 Facsimile: +81-568-33-8591 panasonic.net/id/pidsx/global All Rights Reserved (c) No.CE-PM254565-12 December, 2015 Specifications are subject to change without notice. 2015 Printed in Japan