SMBJ / SMCJ Series Surface Mount Voltage Suppressors TRANSIENT VOLTAGE SUPPRESSOR Features: * For surface mounted applications in order to optimise board space. * Low profile package. * Built-in strain relief. * Glass passivated junction. * Excellent clamping capability. * Low inductance. * Repetition Rate (duty cycle) : 0.05% (SMCJ). : 0.01% (SMBJ). * Fast response time * Typical ID less than 1A above 10V. * High temperature soldering : typically less than 1.0ps from 0 volts to BV minimum. : 250C/10 seconds (SMCJ). : 260C/10 seconds (SMBJ). Dimensional Table Dimensions Rating (W) Type 600 1500 A B C SMBJ 2.11 4.57 3.94 SMCJ 3.15 7.11 6.22 Dimensions : Millimetres Page 1 05/10/05 V1.1 SMBJ / SMCJ Series Surface Mount Voltage Suppressors SMC/DO-214AB Mechanical Data Case : JEDEC DO-214AA moulded plastic over passivated junction (SMCJ). : JEDEC DO-214AB moulded plastic over passivated junction (SMBJ). Terminals : Solder plated, solderable per MIL-STD-750, Method 2026. Polarity : Indicated by cathode band. Standard packaging : 16mm tape per (EIA 481) (SMCJ). 12mm tape per (EIA 481) (SMBJ). Weight: 0.007 ounce, 0.21 gram (SMCJ). 0.003 ounce, 0.093 gram (SMBJ). SMB/DO-214AA Dimensions in inches and (millimetres) Page 2 05/10/05 V1.1 SMBJ / SMCJ Series Surface Mount Voltage Suppressors Maximum Ratings and Electrical Characteristics Ratings at 25C ambient temperature unless otherwise specified. Rating Symbol Peak Pulse Power Dissipation on 10/1000s waveform (Note 1 & 2 - Fig 1) Peak Pulse Current on 10/1000s waveform (Note 1 - Fig 3) Peak forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method - Note 2 & 3) Value Units PPPM Minimum 600 Watts IPPM - Amps IFSM 100.0 Amps TJ, TSTG Operating Junction and Storage Temperature Range -55 to +150 C Notes: 1. Non-repetitive current pulse, per Fig. 3 and derated above TA = 25C per Fig. 2. 2. Mounted on 8.0mm2 copper pads to each terminal (SMCJ). Mounted on 5.0mm2 (.013mm thick) land areas (SMBJ). 3. Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minutes maximum. 100 NON-REPETITIVE PULSE WAVEFORM SHOWN IN FIGURE 3 TA = 25C 10 1.0 MOUNTED ON 5.0mm2 COPPER LAND AREAS 0.1 0.1s 1.0s 10s 100s 1.0ms 10ms PEAK PULSE POWER(pppm) OR CURRENT (Ipp)DERATING IN PERCENTAGE % PPPM , PEAK PULSE POWER, KW MAXIMUM RATINGS AND CHARACTERISTIC CURVES td, PULSE WIDTH, SEC 100 75 50 25 0 0 25 50 75 100 125 150 175 200 TA , AMBIENT TEMPERATURE, C Fig. 1-PEAK PULSE POWER RATING CURVE Fig. 2-PULSE DERATING CURVE Page 3 05/10/05 V1.1 SMBJ / SMCJ Series Surface Mount Voltage Suppressors MAXIMUM RATINGS AND CHARACTERISTIC CURVES 20,000 TA = 25C tf = 10sec 10,000 Pulse Width(td) is Defined as the Point Where the Peak Current Decays to 50% of l pp Peak Value Ippm CJ, CAPACITANCE, pF 100 Half Value-Ipp 2 10/ 50 Waveform as Defined by R.E.A. 1,000 MEASURED AT ZERO BIAS TJ = 25C f = 1.0MHz Vsig = 50mVp-p MEASURED AT STAND-OFF VOLTAGE(VMW) 100 e-kt td 0 0 1.0 2.0 10 1.0 3.0 t, TIME , ms 2.0 10 20 200 400 V(WM), REVERSE STAND-OFF VOLTAGE, VOLTS Fig. 3-PULSE WAVEFORM Fig. 4-TYPICAL JUNCTION CAPACITANCE 200 IFSM, PEAK FORWARD SURGE CURRENT, AMPERES Ippm, PEAK PULSE CURRENT, % 150 TJ = TJ max 8.3ms SINGLE HALF SINCE-WAV E JEDEC METHOD 100 50 0 1 2 4 6 8 10 20 60 80 100 NUMBER OF CYCLES AT 60Hz Fig. 5-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT Page 4 05/10/05 V1.1 SMBJ / SMCJ Series Surface Mount Voltage Suppressors Uni-Directional 600 Watt Surface Mount TVS Breakdown Breakdown Voltage Voltage Vbr (V) Vbr (V) Minimum at IT Maximum at IT Test Current Itest (mA) Maximum Clamping Voltage Vclamp (V) Peak Pulse Current IPP (A) Part Number 10 9.2 65.2 SMBJ5.0A 9.58 12.9 46.5 SMBJ7.5A 13.3 15.3 19.9 30.2 SMBJ12A 15.0 16.7 19.2 24.4 24.0 SMBJ15A LZ 24.0 26.7 30.7 38.9 15.4 SMBJ24A MK 30.0 33.3 38.3 48.4 12.4 SMBJ30A Maximum Clamping Voltage Vclamp (V) Peak Pulse Current IPP (A) Part Number 9.2 163.0 SMCJ5.0A 10.3 145.6 SMCJ6.0A Device Marking Code Stand-Off Voltage Vrm (V) KE 5.0 6.4 7.25 KP 7.5 8.33 LE 12.0 LM 1 Uni-Directional 1500 Watt Surface Mount TVS Breakdown Breakdown Voltage Voltage Vbr (V) Vbr (V) Minimum at IT Maximum at IT Device Marking Code Stand-Off Voltage Vrm (V) Test Current Itest (mA) GDE 5 6.4 7.25 GDG 6 6.67 7.67 GDV 9 10.0 11.5 15.4 97.4 SMCJ9.0A GEE 12 13.3 15.3 19.9 75.3 SMCJ12A GEM 15 16.7 19.2 24.4 61.5 SMCJ15A GEX 22 24.4 28.0 35.5 42.2 SMCJ22A GFM 33 36.7 42.2 53.3 28.1 SMCJ33A GFX 48 53.3 61.3 77.4 19.4 SMCJ48A 10 1 Page 5 05/10/05 V1.1 SMBJ / SMCJ Series Surface Mount Voltage Suppressors Bi-Directional 600 Watt Surface Mount TVS Breakdown Breakdown Voltage Voltage Vbr (V) Vbr (V) Minimum at IT Maximum at IT Test Current Itest (mA) Maximum Clamping Voltage Vclamp (V) Peak Pulse Current IPP (A) Part Number 10 9.2 65.2 SMBJ5.0CA 9.58 12.9 46.5 SMBJ7.5CA 13.3 15.3 19.9 30.2 SMBJ12CA 15.0 16.7 19.2 24.4 24.0 SMBJ15CA BZ 24.0 26.7 30.7 38.9 15.4 SMBJ24CA CK 30.0 33.3 38.3 48.4 12.4 SMBJ30CA Maximum Clamping Voltage Vclamp (V) Peak Pulse Current IPP (A) Part Number 9.2 163.0 SMCJ5.0CA 10.3 145.6 SMCJ6.0CA Device Marking Code Stand-Off Voltage Vrm (V) AE 5.0 6.4 7.25 AP 7.5 8.33 BE 12.0 BM 1 Bi-Directional 1500 Watt Surface Mount TVS Breakdown Breakdown Voltage Voltage Vbr (V) Vbr (V) Minimum at IT Maximum at IT Device Marking Code Stand-Off Voltage Vrm (V) Test Current Itest (mA) BDE 5 6.4 7.25 BDG 6 6.67 7.67 BDV 9 10.0 11.5 15.4 97.4 SMCJ9.0CA BEE 12 13.3 15.3 19.9 75.3 SMCJ12CA BEM 15 16.7 19.2 24.4 61.5 SMCJ15CA BEX 22 24.4 28.0 35.5 42.2 SMCJ22CA BFM 33 36.7 42.2 53.3 28.1 SMCJ33CA BFX 48 53.3 61.3 77.4 19.4 SMCJ48CA 10 1 Part Number Explanation: SM CJ 5.0 A Type Wattage Rating Voltage Suffix Type Wattage Rating : BJ = 600W and CJ = 1500W. Voltage : 5.0, 6.0, 7.5, 9.0, 12, 15, 22, 24, 30, 33 and 48V. Suffix Type : A = Uni-directional and CA = Bi-directional. Page 6 05/10/05 V1.1 SMBJ / SMCJ Series Surface Mount Voltage Suppressors Notes: International Sales Offices: AUSTRALIA - Farnell InOne FINLAND - Farnell InOne NETHERLANDS - Farnell InOne SWITZERLAND - Farnell InOne Tel No: Tel No: Tel No: ++ 61 2 9645 8888 Fax No: ++ 61 2 9644 7898 Fax No: ++ 358 9 345 5411 Fax No: ++ 31 30 241 7333 Tel No: ++ 41 1 204 64 64 Fax No: ++ 41 1 204 64 54 AUSTRIA - Farnell InOne FRANCE - Farnell InOne NEW ZEALAND - Farnell InOne UK - Farnell InOne Tel No: Tel No: Tel No: Tel No: ++ 43 662 2180 680 ++ 358 9 560 7780 ++ 33 474 68 99 99 ++ 31 30 241 7373 ++ 64 9 357 0646 ++ 44 8701 200 200 Fax No: ++ 43 662 2180 670 Fax No: ++ 33 474 68 99 90 Fax No: ++ 64 9 357 0656 Fax No: ++ 44 8701 200 201 BELGIUM - Farnell InOne GERMANY - Farnell InOne NORWAY - Farnell InOne UK - BuckHickman InOne Tel No: Tel No: Tel No: ++ 45 44 53 66 66 ++ 44 8450 510 150 ++ 32 3 475 2810 ++ 49 89 61 39 39 39 Fax No: ++ 32 3 227 3648 Fax No: ++ 49 89 613 59 01 Fax No: ++ 45 44 53 66 02 ++ 44 8450 510 130 BRAZIL - Farnell-Newark InOne HONG KONG - Farnell-Newark InOne Tel No: ++ 852 2268 9888 PORTUGAL - Farnell InOne UK - CPC ++ 55 11 4066 9400 Tel No: ++ 34 93 475 8804 ++ 44 8701 202 530 Fax No: ++ 55 11 4066 9410 Fax No: ++ 852 2268 9899 Fax No: ++ 34 93 474 5288 ++ 44 8701 202 531 CHINA - Farnell-Newark InOne IRELAND - Farnell InOne SINGAPORE - Tel No: Tel No: Tel No: ++86 10 6238 5152 Fax No: ++86 10 6238 5022 Farnell-Newark InOne Tel No: ++ 65 6788 0200 ++ 353 1 830 9277 Fax No: ++ 353 1 830 9016 Fax No: ++ 65 6788 0300 export EXPORT - Farnell InOne Tel No: ++ 44 8701 200 208 Fax No: ++ 44 8701 200 209 For enquiries from all other markets DENMARK - Farnell InOne ITALY - Farnell InOne SPAIN - Farnell InOne Tel No: Tel No: Tel No: ++ 45 44 53 66 44 ++ 39 02 93 995 200 ++ 34 93 475 8805 Fax No: ++ 45 44 53 66 06 Fax No: ++ 39 02 93 995 300 Fax No: ++ 34 93 474 5107 ESTONIA - Farnell InOne MALAYSIA - SWEDEN - Farnell InOne http://www.farnellinone.com Tel No: ++ 358 9 560 7780 Fax No: ++ 358 9 345 5411 Farnell-Newark InOne Tel No: ++ 60 3 7873 8000 Fax No: ++ 60 3 7873 7000 Tel No: ++ 46 8 730 50 00 Fax No: ++ 46 8 83 52 62 http://www.buckhickmaninone.com http://www.cpc.co.uk Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2004. Page 7 05/10/05 V1.1