LTM4612
1
4612fc
For more information www.linear.com/LTM4612
TYPICAL APPLICATION
FEATURES
APPLICATIONS
DESCRIPTION
EN55022B Compliant
36VIN, 15VOUT, 5A,
DC/DC
µ
Module Regulator
The LT M
®
4612 is a EN55022 Class B certified high voltage
input and output, 5A switching mode DC/DC power supply.
Included in the package are the switching controller, power
FETs, inductor and all support components. Operating
over an input voltage range of 5V to 36V, the LTM4612
supports an output voltage range of 3.3V to 15V, set by a
single resistor. Only bulk input and output capacitors are
needed to finish the design.
High switching frequency and an adaptive on-time current
mode architecture enables a very fast transient response
to line and load changes without sacrificing stability.
The onboard input filter and noise cancellation circuits
achieve low noise coupling, thus effectively reducing the
electromagnetic interference (EMI)—see Figures 4 and 8.
Furthermore, the DC/DC µModule
®
regulator can be syn-
chronized with an external clock to reduce undesirable
frequency harmonics and allow PolyPhase
®
operation for
high load currents.
The LTM4612 is offered in a space saving and thermally
enhanced 15mm × 15mm × 2.8mm LGA package, which
enables utilization of unused space on the bottom of PC
boards for high density point-of-load regulation. The
LTM4612 is Pb-free and RoHS compliant.
L, LT, LTC, LTM, Linear Technology, the Linear logo, PolyPhase and µModule are registered
trademarks and LTpowerCAD is a trademark of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
5V/5A Ultralow Noise µModule with 7V to 36V Input
n Complete Low EMI Switch Mode Power Supply
n EN55022 Class B Compliant
n Wide Input Voltage Range: 5V to 36V
n 3.3V to 15V Output Voltage Range
n 5A DC, 7A Peak Output Current
n Low Input and Output Referred Noise
n Output Voltage Tracking and Margining
n Power Good Tracks with Margining
n PLL Frequency Synchronization
n ±1.5% Set Point Accuracy
n Current Foldback Protection (Disabled at Start-Up)
n Parallel/Current Sharing
n Ultrafast Transient Response
n Current Mode Control
n Programmable Soft-Start
n Output Overvoltage Protection
n –55°C to 125°C Operating Temperature Range
(LTM4612MPV)
n Small Surface Mount Footprint, Low Profile
(15mm × 15mm × 2.8mm) LGA Package
n Telecom and Networking Equipment
n Industrial and Avionic Equipment
n RF Systems
Radiated Emission Scan at 24VIN, 5VOUT/5A
FREQUENCY (MHz)
30
dBµV/m
30
70
128.1
226.2
324.3
10
60
20
0
–10
50
40
422.4
520.5
618.6
716.7
814.8
912.9
1010
EN55022 CLASS B LIMIT
4612 TA01b
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
FCB
MARG0
MARG1
MPGM
VOUT
VFB
VIN
0.01µF
10µF
100pF COUT
VOUT
5V
5A
CIN
VIN
7V
TO 36V PLLIN
CLOCK SYNC
LTM4612
SGND
VD
PGND
MARGIN
CONTROL
100k
2M
13.7k
392k
5% MARGIN
4612 TA01
LTM4612
2
4612fc
For more information www.linear.com/LTM4612
PIN CONFIGURATIONABSOLUTE MAXIMUM RATINGS
INTVCC, DRVCC ............................................. 0.3V to 6V
VOUT ........................................................... 0.3V to 16V
PLLIN, FCB, TRACK/SS, MPGM, MARG0,
MARG1, PGOOD ....................0.3V to INTVCC + 0.3V
RUN .............................................................0.3V to 5V
VFB, COMP ................................................ 0.3V to 2.7V
VIN, VD ....................................................... 0.3V to 36V
Internal Operating Temperature Range (Note 2)
E and I Grades ................................... 40°C to 125°C
MP Grade ........................................... 55°C to 125°C
Junction Temperature ........................................... 125°C
Storage Temperature Range .................. 55°C to 125°C
(Note 1)
MARG1
DRVCC
VFB
PGOOD
SGND
NC
NC
NC
FCB
VIN
BANK 1 VD
PGND
BANK 2
VOUT
BANK 3
fSET
MARG0
RUN
COMP
MPGM
PLLIN
INTVCC
TRACK/SS
LGA PACKAGE
133-LEAD (15mm × 15mm × 2.8mm)
TOP VIEW
SGND
1221 43 5 6 98 10 117
A
B
C
D
E
F
G
H
J
K
L
M
TJMAX = 125°C, θJA = 15°C/W, θJC = 6°C/W
θJA DERIVED FROM 95mm × 76mm PCB WITH 4 LAYERS
WEIGHT = 1.7g
ORDER INFORMATION
LEAD FREE FINISH TRAY PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE
LTM4612EV#PBF LTM4612EV#PBF LTM4612V 133-Lead (15mm × 15mm × 2.8mm) LGA –40°C to 125°C
LTM4612IV#PBF LTM4612IV#PBF LTM4612V 133-Lead (15mm × 15mm × 2.8mm) LGA –40°C to 125°C
LTM4612MPV#PBF LTM4612MPV#PBF LTM4612MPV 133-Lead (15mm × 15mm × 2.8mm) LGA –55°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
This product is only offered in trays. For more information go to: http://www.linear.com/packaging/
ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VIN(DC) Input DC Voltage l5 36 V
VOUT(DC) Output Voltage CIN = 10µF × 3, COUT = 300µF; FCB = 0
VIN = 24V, VOUT = 12V, IOUT = 0A
VIN = 36V, VOUT=12V, IOUT = 0A
l
l
11.83
11.83
12.07
12.07
12.31
12.31
V
V
Input Specifications
VIN(UVLO) Undervoltage Lockout Threshold IOUT = 0A 3.2 4.8 V
IINRUSH(VIN) Input Inrush Current at Start-Up IOUT = 0A; CIN = 10µF × 2, COUT = 200µF;
VOUT = 12V
VIN = 24V
VIN = 36V
0.6
0.7
A
A
The l denotes the specifications which apply over the specified internal
operating temperature range, otherwise specifications are at TA = 25°C, VIN = 24V, unless otherwise noted (Note 2). Per Typical
Application (front page) configuration.
http://www.linear.com/product/LTM4612#orderinfo
LTM4612
3
4612fc
For more information www.linear.com/LTM4612
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified internal
operating temperature range, otherwise specifications are at TA = 25°C, VIN = 24V, unless otherwise noted (Note 2). Per Typical
Application (front page) configuration.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
IQ(VIN) Input Supply Bias Current VIN = 36V, VOUT = 12V, Switching Continuous
VIN = 24V, VOUT = 12V, Switching Continuous
Shutdown, RUN = 0, VIN = 36V
57
48
50
mA
mA
µA
IS(VIN) Input Supply Current VIN = 36V, VOUT = 12V, IOUT = 5A
VIN = 24V, VOUT = 12V, IOUT = 5A
1.85
2.72
A
A
VINTVCC Internal VCC Voltage VIN = 36V, RUN > 2V, IOUT = 0A 4.7 5 5.5 V
Output Specifications
IOUT(DC) Output Continuous Current Range VIN = 24V, VOUT = 12V (Note 4) 0 5 A
DVOUT(LINE)
VOUT
Line Regulation Accuracy VOUT = 12V, FCB = 0V, VIN = 22V to 36V,
IOUT = 0A
l
0.05
0.3
%
DVOUT(LOAD)
VOUT
Load Regulation Accuracy VOUT = 12V, FCB = 0V, IOUT = 0A to 5A (Note 4)
VIN = 36V
VIN = 24V
l
l
0.3
0.3
0.6
0.6
%
%
VIN(AC) Input Ripple Voltage IOUT = 0A,
CIN = 2 × 10µF X5R Ceramic and 1 × 100µF
Electrolytic, 1 × 10µF X5R Ceramic on VD Pins
VIN = 24V, VOUT = 5V
VIN = 24V, VOUT = 12V
7.2
3.4
mVP-P
mVP-P
VOUT(AC) Output Ripple Voltage IOUT = 0A,
COUT = 2 × 22µF, 2 × 47µF X5R Ceramic
VIN = 24V, VOUT = 5V
VIN = 24V, VOUT = 12V
17.5
12.5
mVP-P
mVP-P
fSOutput Ripple Voltage Frequency IOUT = 1A, VIN = 24V, VOUT = 12V 940 kHz
DVOUT(START) Turn-On Overshoot,
TRACK/SS = 10nF
COUT = 200µF, VOUT = 12V, IOUT = 0A
VIN = 36V
VIN = 24V
20
20
mV
mV
tSTART Turn-On Time, TRACK/SS = Open COUT = 300µF, VOUT = 12V, IOUT = 1A
Resistive Load
VIN = 36V
VIN = 24V
0.5
0.5
ms
ms
DVOUT(LS) Peak Deviation for Dynamic Load Load: 0% to 50% to 0% of Full Load
COUT = 2 × 22µF Ceramic, 150µF Bulk
VIN = 24V, VOUT = 12V
153
mV
tSETTLE Settling Time for Dynamic Load Step Load: 0% to 50% to 0% of Full Load, VIN = 24V 37 µs
IOUT(PK) Output Current Limit COUT = 200µF
VIN = 36V, VOUT = 12V
VIN = 24V, VOUT = 12V
9
9
A
A
Control Section
VFB Voltage at VFB Pin IOUT = 0A, VOUT = 12V l0.591 0.6 0.609 V
VRUN RUN Pin On/Off Threshold 1 1.5 1.9 V
ISS / TRACK Soft-Start Charging Current VSS / TRACK = 0V –1 –1.5 –2 µA
VFCB Forced Continuous Threshold 0.57 0.6 0.63 V
IFCB Forced Continuous Pin Current VFCB = 0V –1 –2 µA
tON(MIN) Minimum On-Time (Note 3) 50 100 ns
tOFF(MIN) Minimum Off-Time (Note 3) 250 400 ns
RPLLIN PLLIN Input Resistor 50 kW
LTM4612
4
4612fc
For more information www.linear.com/LTM4612
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTM4612E is guaranteed to meet performance specifications
over the 0°C to 125°C internal operating temperature range. Specifications
over the –40°C to 125°C internal operating temperature range are assured
by design, characterization and correlation with statistical process
controls. The LTM4612I is guaranteed to meet specifications over the
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
IDRVCC Current into DRVCC Pin VOUT = 12V, IOUT = 1A 22 30 mA
RFBHI Resistor Between VOUT and VFB Pins 99.5 100 100.5 kW
VMPGM Margin Reference Voltage 1.18 V
VMARG0, VMARG1 MARG0, MARG1 Voltage Thresholds 1.4 V
PGOOD
DVFBH PGOOD Upper Threshold VFB Rising 7 10 13 %
DVFBL PGOOD Lower Threshold VFB Falling –7 –10 –13 %
DVFB(HYS) PGOOD Hysteresis VFB Returning 1.5 %
VPGL PGOOD Low Voltage IPGOOD = 5mA 0.15 0.4 V
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified internal
operating temperature range, otherwise specifications are at TA = 25°C, VIN = 24V, unless otherwise noted (Note 2). Per Typical
Application (front page) configuration.
–40°C to 125°C internal operating temperature range. The LTM4612MP
is guaranteed and tested over the full –55°C to 125°C internal operating
temperature range. Note that the maximum ambient temperature
consistent with these specifications is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
resistance and other environmental factors.
Note 3: 100% tested at die level only.
Note 4: See the Output Current Derating curves for different VIN, VOUT
and TA.
LTM4612
5
4612fc
For more information www.linear.com/LTM4612
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs Load Current with
3.3VOUT (FCB = 0)
Efficiency vs Load Current with
5VOUT (FCB = 0)
Efficiency vs Load Current with
12VOUT (FCB = 0)
Efficiency vs Load Current with
15VOUT (FCB = 0, Refer to Figure 20)
Transient Response from 12VIN
to 3.3VOUT
Transient Response from 12VIN
to 5VOUT
Transient Response from 24VIN
to 12VOUT
Start-Up with 24VIN to 12VOUT
at IOUT = 0A
Start-Up with 24VIN to 12VOUT at
IOUT = 5A
(Refer to Figure 18)
LOAD CURRENT (A)
0
EFFICIENCY (%)
70
95
100
123
60
85
65
90
55
50
80
75
45
4612 G01
5VIN 3.3VOUT
12VIN 3.3VOUT
24VIN 3.3VOUT
36VIN 3.3VOUT
LOAD CURRENT (A)
0
EFFICIENCY (%)
70
95
123
60
85
65
90
55
50
80
75
45
4612 G02
12VIN 5VOUT
24VIN 5VOUT
36VIN 5VOUT
LOAD CURRENT (A)
0
EFFICIENCY (%)
70
95
100
123
60
85
65
90
55
50
80
75
45
4612 G03
20VIN 12VOUT
24VIN 12VOUT
28VIN 12VOUT
36VIN 12VOUT
LOAD CURRENT (A)
0
EFFICIENCY (%)
70
100
95
123
60
85
65
90
80
75
45
4612 G04
28VIN 15VOUT
32VIN 15VOUT
36VIN 15VOUT
50µs/DIV
2A/DIV
100mV/DIV
4612 G05
LOAD STEP: 0A to 3A
COUT = 2 × 22µF CERAMIC CAPACITORS AND
2 × 47µF CERAMIC CAPACITORS
50µs/DIV
2A/DIV
100mV/DIV
4612 G06
LOAD STEP: 0A to 3A
COUT = 2 × 22µF CERAMIC CAPACITORS AND
2 × 47µF CERAMIC CAPACITORS
50µs/DIV
2A/DIV
200mV/
DIV
4612 G07
LOAD STEP: 0A to 3A
COUT = 2 × 22µF CERAMIC CAPACITORS AND
2 × 47µF CERAMIC CAPACITORS
500µs/DIV
IIN
0.2A/DIV
VOUT
5V/DIV
4612 G08
SOFT-START CAPACITOR: 3.9nF
CIN = 3 × 10µF CERAMIC CAPACITORS AND
1 × 47µF OSCON CAPACITOR
500µs/DIV
IIN
1A/DIV
VOUT
5V/DIV
4612 G09
SOFT-START CAPACITOR: 3.9nF
CIN = 3 × 10µF CERAMIC CAPACITORS AND
1 × 47µF OSCON CAPACITOR
LTM4612
6
4612fc
For more information www.linear.com/LTM4612
TYPICAL PERFORMANCE CHARACTERISTICS
Start-Up with 24VIN to 12VOUT at
IOUT = 5A, TA = –55°C
Short-Circuit with 24VIN to 12VOUT
at IOUT = 0A
Short-Circuit with 24VIN to 12VOUT
at IOUT = 5A
VIN to VOUT Step-Down Ratio
Input Ripple
Output Ripple
500µs/DIV
IIN
1A/DIV
VOUT
5V/DIV
4612 G10
SOFT-START CAPACITOR: 3.9nF
CIN = 3 × 10µF CERAMIC CAPACITORS AND
1 × 47µF OSCON CAPACITOR
50µs/DIV
IIN
0.2A/DIV
VOUT
5V/DIV
4612 G11
COUT = 2 × 22µF CERAMIC CAPACITORS AND
2 × 47µF CERAMIC CAPACITORS
20µs/DIV
IIN
2A/DIV
VOUT
5V/DIV
4612 G12
COUT = 2 × 22µF CERAMIC CAPACITORS AND
2 × 47µF CERAMIC CAPACITORS
3.3
24
30
18
12
6 10
4
8 12 14 15
6
0
36
4612 G13
SEE FREQUENCY ADJUSTMENT SECTION
FOR OPERATIONS OUTSIDE THIS REGION
OPERATING REGION
WITH DEFAULT FREQUENCY
VOUT (V)
V
IN
(V)
1µs/DIV
50mV/DIV
4612 G14
VIN = 24V
VOUT = 12V AT 5A RESISTIVE LOAD
CIN = 3 × 10µF 50V CERAMIC 1 × 100µF BULK
1µs/DIV
10mV/DIV
4612 G15
VIN = 24V
VOUT = 12V AT 5A RESISTIVE LOAD
COUT = 2 × 22µF 16V CERAMIC AND
2 × 47µF 16V CERAMIC
LTM4612
7
4612fc
For more information www.linear.com/LTM4612
PIN FUNCTIONS
VIN (Bank 1): Power Input Pins. Apply input voltage be-
tween these pins and PGND pins. Recommend placing
input decoupling capacitance directly between VIN pins
and PGND pins.
PGND (Bank 2): Power Ground Pins for Both Input and
Output Returns.
VOUT (Bank 3): Power Output Pins. Apply output load
between these pins and PGND pins. Recommend placing out-
put decoupling capacitance directly between these pins and
GND pins (see the L
TM4612 Pin Configuration below).
VD (Pins B7, C7): Top FET Drain Pins. Add more capa-
citors between VD and ground to handle the input RMS
current and reduce the input ripple further.
DRVCC (Pins C10, E11, E12): These pins normally connect
to INTVCC for powering the internal MOSFET drivers. They
can be biased up to 6V from an external supply with about
50mA capability. This improves efficiency at higher input
voltages by reducing power dissipation in the module.
INTVCC (Pin A7): This pin is for additional decoupling of
the 5V internal regulator.
PLLIN (Pin A8): External Clock Synchronization Input to the
Phase Detector. This pin is internally terminated to SGND
with a 50k resistor. Apply a clock above 2V and below
INTVCC. See the Applications Information section.
FCB (Pin M12): Forced Continuous Input. Connect this pin
to SGND to force continuous synchronization operation at
low load, to INTVCC to enable discontinuous mode opera-
tion at low load or to a resistive divider from a secondary
output when using a secondary winding.
TRACK/SS (Pin A9): Output Voltage Tracking and Soft-Start
Pin. When the module is configured as a master output,
then a soft-start capacitor is placed on this pin to ground
to control the master ramp rate. A soft-start capacitor can
be used for soft-start turn-on as a standalone regulator.
Slave operation is performed by putting a resistor divider
from the master output to the ground, and connecting the
center point of the divider to this pin. See the Applications
Information section.
MPGM (Pins A12, B11): Programmable Margining In-
put. A resistor from these pins to ground sets a current
that is equal to 1.18V/R. This current multiplied by 10k
will equal a value in millivolts that is a percentage of the
0.6V reference voltage. May be left open if margining is
not desired. See the Applications Information section. To
parallel LTM4612s, each requires an individual MPGM
resistor. Do not tie MPGM pins together.
fSET (Pin B12): Frequency Set Internally to ~850kHz to
900kHz at 12V Output. An external resistor can be placed
from this pin to ground to increase frequency. See the
Applications Information section for frequency adjustment.
LTM4612 Pin Configuration
(See Package Description for Pin Assignments)
MARG1
DRVCC
VFB
PGOOD
SGND
NC
NC
NC
FCB
VIN
BANK 1 VD
PGND
BANK 2
VOUT
BANK 3
fSET
MARG0
RUN
COMP
MPGM
PLLIN
INTVCC
TRACK/SS
LGA PACKAGE
133-LEAD (15mm × 15mm × 2.8mm)
TOP VIEW
SGND
1221 43 5 6 98 10 117
A
B
C
D
E
F
G
H
J
K
L
M
LTM4612
8
4612fc
For more information www.linear.com/LTM4612
VFB (Pin F12): The Negative Input of the Error Ampli-
fier. Internally, this pin is connected to VOUT with a 100k
0.5% precision resistor. Different output voltages can be
programmed with an additional resistor between the VFB
and SGND pins. See the Applications Information section.
MARG0 (Pin C12): LSB Logic Input for the Margining
Function. Together with the MARG1 pin, the MARG0 pin
will determine if a margin high, margin low, or no margin
state is applied. The pin has an internal pull-down resistor
of 50k. See the Applications Information section.
MARG1 (Pins C11, D12): MSB Logic Input for the Margin-
ing Function. Together with the MARG0 pin, the MARG1 pin
will determine if a margin high, margin low, or no margin
state is applied. The pins have an internal pull-down resistor
of 50k. See the Applications Information section.
SGND (Pins D9, H12): Signal Ground Pins. These pins
connect to PGND at output capacitor point.
COMP (Pins A11, D11): Current Control Threshold and
Error Amplifier Compensation Point. The current com-
parator threshold increases with this control voltage. The
voltage ranges from 0V to 2.4V with 0.7V corresponding
to zero sense voltage (zero current).
PGOOD (Pin G12): Output Voltage Power Good Indicator.
Open-drain logic output that is pulled to ground when the
output voltage is not within ±10% of the regulation point,
after a 25µs power bad mask timer expires.
RUN (Pins A10, B9): Run Control Pins. A voltage above
1.9V will turn on the module, and below 1V will turn off
the module. A programmable UVLO function can be ac-
complished with a resistor from VIN to this pin that is has
a 5.1V zener to ground. Maximum pin voltage is 5V.
NC (Pins J12, K12, L12): No Connect Pins. Leave floating.
PIN FUNCTIONS
LTM4612
9
4612fc
For more information www.linear.com/LTM4612
BLOCK DIAGRAM
DECOUPLING REQUIREMENTS
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
CIN External Input Capacitor Requirement
(VIN = 20V to 36V, VOUT = 12V)
IOUT = 4A 20 µF
COUT External Output Capacitor Requirement
(VIN = 20V to 36V, VOUT = 12V)
IOUT = 4A 100 150 µF
Specifications are at TA = 25°C. Use Figure 1 configuration.
+
INTERNAL
COMP
SGND
COMP
PGOOD
RUN
> 1.9V = ON
< 1V = OFF
MAX = 5V
MARG1
MARG0
MPGM
FCB
PLLIN
CSS
INTVCC
DRVCC
TRACK/SS
VFB
fSET
50k
93.1k
RFB
5.23k
50k
100k
VOUT
5.1V
ZENER
POWER CONTROL M1
VIN
20V TO 36V
VD
VOUT
12V
AT 4A
M2
50k
10µF
F CIN
+
COUT
PGND
4612 F01
CD
10k
4.7µF
INPUT
FILTER
2.7µH
NOISE
CANCEL-
LATION
Figure 1. Simplified Block Diagram
LTM4612
10
4612fc
For more information www.linear.com/LTM4612
OPERATION
Power Module Description
The LTM4612 is a standalone nonisolated switching mode
DC/DC power supply. It can deliver 5A of DC output
current with some external input and output capacitors.
This module provides precisely regulated output voltage
programmable via one external resistor from 3.3VDC to
15VDC over a 5V to 36V wide input voltage. The typical
application schematic is shown in Figure 18.
The LTM4612 has an integrated constant on-time current
mode regulator, ultralow RDS(ON) FETs with fast switching
speed and integrated Schottky diodes. The typical switching
frequency is 850kHz at full load at 12V output. With current
mode control and internal feedback loop compensation,
the LTM4612 module has sufficient stability margins and
good transient performance under a wide range of operat-
ing conditions and with a wide range of output capacitors,
even all ceramic output capacitors.
Current mode control provides cycle-by-cycle fast current
limiting. Moreover, foldback current limiting is provided in
an overcurrent condition while VFB drops. Internal over-
voltage and undervoltage comparators pull the open-drain
PGOOD output low if the output feedback voltage exits a
±10% window around the regulation point. Furthermore,
in an overvoltage condition, internal top FET M1 is turned
off and bottom FET M2 is turned on and held on until the
overvoltage condition clears.
Input filter and noise cancellation circuitry reduce the noise
coupling to I/O sides, and ensure the electromagnetic
interference (EMI) meets the limits of EN55022 Class B.
Pulling the RUN pin below 1V forces the controller into
its shutdown state, turning off both M1 and M2. At light
load currents, discontinuous mode (DCM) operation can
be enabled to achieve higher efficiency compared to con-
tinuous mode (CCM) by setting FCB pin higher than 0.6V.
When the DRVCC pin is connected to INTVCC, an integrated
5V linear regulator powers the internal gate drivers. If a
5V external bias supply is applied on DRVCC pin, then an
efficiency improvement will occur due to the reduced power
loss in the internal linear regulator. This is especially true
at higher input voltages.
The MPGM, MARG0, and MARG1 pins are used to sup-
port output voltage margining, where the percentage of
margin is programmed by the MPGM pin, and the MARG0
and MARG1 select margining. The PLLIN pin provides
frequency synchronization of the device to an external
clock. The TRACK/SS pin is used for power supply track-
ing and soft-start programming.
The typical L
TM4612 application circuit is shown in Figure
18. External component selection is primarily determined
by the maximum load current and output voltage. Refer
to Table 2 for specific external capacitor requirements for
a particular application.
APPLICATIONS INFORMATION
VIN to VOUT Stepdown Ratios
There are restrictions in the maximum VIN and VOUT step
down ratio that can be achieved for a given input voltage.
These constraints are shown in the Typical Performance
Characteristic curve labeled “VIN to VOUT Step-Down
Ratio.” Note that additional thermal derating may be ap-
plied. See the Thermal Considerations and Output Current
Derating section in this data sheet.
LTM4612
11
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Output Voltage Programming and Margining
The PWM controller has an internal 0.6V reference voltage.
As shown in the Block Diagram, a 100k internal feedback
resistor connects the VOUT and VFB pins together. Adding a
resistor, RFB, from the VFB pin to the SGND pin programs
the output voltage.
VOUT =0.6V
100k
+
R
FB
R
FB
or equivalently,
RFB =
100k
VOUT
0.6V
1
Table 1. RFB Standard 1% Resistor Values vs VOUT
VOUT (V) 3.3 5 6 8 10 12 14 15
RFB (kW)22.1 13.7 11 8.06 6.34 5.23 4.42 4.12
The MPGM pin programs a current that when multiplied
by an internal 10k resistor sets up the 0.6V reference ±
offset for margining. A 1.18V reference divided by the
Table 2. Output Voltage Response vs Component Matrix (Refer to Figure 20)
TYPICAL MEASURED VALUES
VENDORS PART NUMBER VENDORS PART NUMBER
Murata GRM32ER61C476KEI5L (47µF, 16V) Murata GRM32ER71H106K (10µF, 50V)
Murata GRM32ER61C226KE20L (22µF, 16V) TDK C3225X5RIC226M (22µF, 16V)
VOUT
(V)
CIN
(CERAMIC)
CIN
(BULK)
COUT1
(CERAMIC)
COUT2
(BULK)
VIN
(V)
DROOP
(mV)
PEAK-TO-
PEAK (mV)
RECOVERY
TIME (µs)
LOAD STEP
(A/µs)
RFB
(kΩ)
5 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 12 86 156 26 3 13.7
5 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 12 86 178 14.8 3 13.7
5 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 24 83 166 27 3 13.7
5 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 24 86 169 14.8 3 13.7
5 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 36 86 178 25 3 13.7
5 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 36 86 172 15.2 3 13.7
10 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 24 111 209 30 3 6.34
10 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 24 171 325 35 3 6.34
10 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 36 108 197 35 3 6.34
10 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 36 153 288 39 3 6.34
12 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 24 153 281 37 3 5.23
12 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 36 184 375 34.4 3 5.23
15 2 × 10µF 50V 100µF 50V 2 × 22µF 16V 150µF 25V 28 178 338 70 3 4.12
15 2 × 10µF 50V 100µF 50V 4 × 47µF 16V None 36 134 250 70 3 4.12
RPGM resistor on the MPGM pin programs the current.
Calculate VOUT(MARGIN):
VOUT(MARGIN) =
%V
OUT
100
VOUT
Where %VOUT is the percentage of VOUT to be margined,
and VOUT(MARGIN) is the margin quantity in volts:
RPGM =
V
OUT
0.6V
1.18V
VOUT(MARGIN)
10k
Where RPGM is the resistor value to place on the MPGM
pin to ground.
The output margining will be ± margining of the value.
This is controlled by the MARG0 and MARG1 pins. See
the truth table below:
MARG1 MARG0 MODE
LOW LOW NO MARGIN
LOW HIGH MARGIN UP
HIGH LOW MARGIN DOWN
HIGH HIGH NO MARGIN
LTM4612
12
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Operating Frequency
The operating frequency of the LTM4612 is optimized to
achieve the compact package size and the minimum
output ripple voltage while still providing high efficiency.
As shown in Figure 2, the frequency is linearly increased
with larger output voltages to keep the low output cur-
rent ripple. Figure 3 shows the inductor current ripple DI
with different output voltages. In most applications, no
additional frequency adjusting is required.
If lower output ripple is required, the operating frequency
f can be increased by adding a resistor RfSET between fSET
pin and SGND, as shown in Figure 19.
f=
V
OUT
1.5 1010 RfSET || 93.1k
( )
Figure 2. Operating Frequency vs Output Voltage Figure 3. Inductor Current Ripple vs Output Voltage
VOUT (V)
2
600
800
1200
8 12
4612 F02
400
4 6 10 14 16
200
1000
FREQUENCY (kHz)
2
2.5
3.0
2.0
1.5
6 10
48 12 14 16
1.0
0.5
3.5
4612 F03
VIN = 36V
VIN = 28V
VIN = 20V
VOUT (V)
INDUCTOR CURRENT RIPPLE ∆I (A)
For output voltages more than 12V, the frequency can be
higher than 1MHz, thus reducing the efficiency significantly.
Additionally, the 500ns minimum off time (400ns + 100ns
for margin) normally limits the operation when the input
voltage is close to the output voltage. Therefore, it is rec-
ommended to lower the frequency in these conditions by
connecting a resistor (RfSET) from the fSET pin to VIN, as
shown in Figure 20.
f=
OUT
5 1011 3 RfSET 93.1k
RfSET 2 93.1k
The load current can affect the frequency due to its constant
on-time control. If constant frequency is a necessity, the
PLLIN pin can be used to synchronize the frequency of
the LTM4612 to an external clock, as shown in Figures
21 to 23.
LTM4612
13
4612fc
For more information www.linear.com/LTM4612
Figure 4. Radiated Emission Scan with 24VIN to
5VOUT at 5A (2 × 10µF Ceramic Capacitors on VIN
Pads and 1 × 10µF Ceramic Capacitor on VD Pads)
APPLICATIONS INFORMATION
Input Capacitors
LTM4612 is designed to achieve the low input radiated EMI
noise due to the fast switching of turn-on and turn-off.
In the LTM4612, a high-frequency inductor is integrated
into the input line for noise attenuation. VD and VIN pins
are available for external input capacitors to form a high
frequency π filter. As shown in Figure 18, the ceramic
capacitor C1 on the VD pins is used to handle most of
the RMS current into the converter, so careful attention
is needed for capacitor C1 selection.
For a buck converter, the switching duty cycle can be
estimated as:
D=
V
OUT
V
IN
Without considering the inductor current ripple, the RMS
current of the input capacitor can be estimated as:
ICIN(RMS) =
I
OUT(MAX)
h D 1 D
( )
In this equation, h is the estimated efficiency of the
power module. Note the capacitor ripple current ratings
are often based on temperature and hours of life. This
makes it advisable to properly derate the input capacitor,
or choose a capacitor rated at a higher temperature than
required. Always contact the capacitor manufacturer for
derating requirements.
In a typical 5A output application, one very low ESR, X5R
or X7R, 10µF ceramic capacitor is recommended for C1.
This decoupling capacitor should be placed directly adja-
cent to the module VD pins in the PCB layout to minimize
the trace inductance and high frequency AC noise. Each
10µF ceramic is typically good for 2A to 3A of RMS ripple
current. Refer to your ceramics capacitor catalog for the
RMS current ratings.
FREQUENCY (MHz)
30
dBµV/m
30
70
128.1
226.2
324.3
10
60
20
0
–10
50
40
422.4
520.5
618.6
716.7
814.8
912.9
1010
EN55022 CLASS B LIMIT
4612 F04
To attenuate the high frequency noise, extra input capacitors
should be connected to the VIN pads and placed before the
high frequency inductor to form the π filter. One of these
low ESR ceramic input capacitors is recommended to be
close to the connection into the system board. A large
bulk 100µF capacitor is only needed if the input source
impedance is compromised by long inductive leads or
traces. Figure 4 shows the radiated EMI test results to
meet the EN55022 Class B limit. For different applica-
tions, input capacitance may be varied to meet different
radiated EMI limits.
LTM4612
14
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Output Capacitors
The LTM4612 is designed for low output voltage ripple.
The bulk output capacitors defined as COUT are chosen
with low enough effective series resistance (ESR) to meet
the output voltage ripple and transient requirements. COUT
can be low ESR tantalum capacitor, low ESR polymer
capacitor or ceramic capacitor. The typical capacitance is
150µF if all ceramic output capacitors are used. Additional
output filtering may be required by the system designer,
if further reduction of output ripple or dynamic transient
spike is required. Table 2 shows a matrix of different output
voltages and output capacitors to minimize the voltage
droop and overshoot during a 2A/µs transient. The table
optimizes total equivalent ESR and total bulk capacitance
to maximize transient performance.
Multiphase operation with multiple LTM4612 devices in
parallel will also lower the effective output ripple current
due to the phase interleaving operation. Refer to Figure 5
for the normalized output ripple current versus the duty
cycle. Figure 5 provides a ratio of peak-to-peak output
ripple current to the inductor ripple current as functions
of duty cycle and the number of paralleled phases. Pick
the corresponding duty cycle and the number of phases
to get the correct output ripple current value. For example,
each phase’s inductor ripple current DIr at zero duty cycle
is ~4.3A for a 36V to 12V design. The duty cycle is about
0.33. The 2-phase curve has a ratio of ~0.33 for a duty
cycle of 0.33. This 0.33 ratio of output ripple current to
the inductor ripple current DIr at 4.3A equals 1.4A of the
output ripple current (DIL).
The output voltage ripple has two components that are
related to the amount of bulk capacitance and effective
series resistance (ESR) of the output bulk capacitance.
The equation is:
DVOUT(P-P) DIL
8 f N COUT
+ESR DIL
where f is the frequency and N is the number of paralleled
phases.
DUTY CYCLE (VO/VIN)
0.1 0.15 0.2 0.25 0.350.3 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
4612 F05
6-PHASE
4-PHASE
3-PHASE
2-PHASE
1-PHASE
PEAK-TO-PEAK OUTPUT RIPPLE CURRENT
DIr
RATIO =
Figure 5. Normalized Output Ripple Current vs Duty Cycle, Dlr = VOT/LI
LTM4612
15
4612fc
For more information www.linear.com/LTM4612
Figure 6. Coincident Tracking Figure 7. Coincident Output Tracking
OUTPUT
VOLTAGE
TIME 4612 F07
MASTER OUTPUT
SLAVE OUTPUT
APPLICATIONS INFORMATION
Fault Conditions: Current Limit and
Overcurrent Foldback
LTM4612 has a current mode controller
, which inherently
limits the cycle-by-cycle inductor current not only in steady
state operation, but also in transient.
To further limit current in the event of an overload condi-
tion, the LTM4612 provides foldback current limiting. If the
output voltage falls by more than 50%, then the maximum
output current is progressively lowered to about one sixth
of its full current limit value.
Soft-Start and Tracking
The TRACK/SS pin provides a means to either soft-start
the regulator or track it to a different power supply. A
capacitor on this pin will program the ramp rate of the
output voltage. A 1.5µA current source will charge up the
external soft-start capacitor to 80% of the 0.6V internal
voltage reference plus or minus any margin delta. This will
control the ramp of the internal reference and the output
voltage. The total soft-start time can be calculated as:
tSOFTSTART 0.8 0.6 ±0.6 VOUT Margin %
( )
C
SS
1.5µA
If the RUN pin falls below 2.5V, then the soft-start pin
is reset to allow for the proper soft-start again. Current
foldback and force continuous mode are disabled during
the soft-start process. The soft-start function can also
be used to control the output ramp rising time, so that
another regulator can be easily tracked.
Output Voltage Tracking
Output voltage tracking can be programmed externally
using the TRACK/SS pin. The output can be tracked up and
down with another regulator. Figure 6 shows an example
of coincident tracking where the master regulators output
is divided down with an external resistor divider that is the
same as the slave regulators feedback divider. Ratiometric
modes of tracking can be achieved by selecting different
resistor values to change the output tracking ratio. The
master output must be greater than the slave output for
the tracking to work. Figure 7 shows the coincident output
tracking.
Tracking can be achieved by a few simple calculations
and the slew rate value applied to the masters TRACK
pin. The TRACK pin has a control range from 0 to 0.6V.
The masters TRACK pin slew rate is directly equal to the
masters output slew rate in Volts/Time. The equation:
MR
SR
100k =R2
where MR is the masters output slew rate and SR is the
slave’s output slew rate in Volts/Time. When coincident
tracking is desired, then MR and SR are equal, thus R2 is
equal the 100k. R1 is derived from equation:
R1=
0.6V
VFB
100k +VFB
R
FB
VTRACK
R2
PGOOD
RUN
COMP
INTVCC
DRVCC
TRACK/SS
fSET
VOUT
VFB
FCB
MARG0
MARG1
MPGM
TRACK
CONTROL
PLLIN
LTM4612
RFB
5.23k
100k 10µF
MASTER
OUTPUT R2
100k
COUT
SLAVE
OUTPUT
4612 F06
CIN
VIN
VD
PGNDSGND
VIN
R1
5.23k
LTM4612
16
4612fc
For more information www.linear.com/LTM4612
where VFB is the feedback voltage reference of the regula-
tor, and VTRACK is 0.6V. Since R2 is equal to the 100k top
feedback resistor of the slave regulator in equal slew rate
or coincident tracking, then R1 is equal to RFB with VFB =
VTRACK. Therefore R2 = 100k, and R1 = 5.23k in Figure 6.
In ratiometric tracking, a different slew rate maybe desired
for the slave regulator. R2 can be solved for when SR is
slower than MR. Make sure that the slave supply slew
rate is chosen to be fast enough so that the slave output
voltage will reach it final value before the master output.
For example, MR = 1.5V/1ms, and SR = 1.2V/1ms. Then
R2 = 125k. Solve for R1 to equal to 5.18k.
Each of the TRACK pins will have the 1.5µA current source
on when a resistive divider is used to implement tracking
on that specific channel. This will impose an offset on the
TRACK pin input. Smaller values resistors with the same
ratios as the resistor values calculated from the above
equation can be used. For example, where the 100k is
used then a 10k can be used to reduce the TRACK pin
offset to a negligible value.
RUN Enable
The RUN pin is used to enable the power module. The
pin has an internal 5.1V Zener to ground. The pin can be
driven with 5V logic levels.
The RUN pin can also be used as an undervoltage lockout
(UVLO) function by connecting a resistor divider from
the input supply to the RUN pin. The equation for UVLO
threshold:
VUVLO =
R
A+
R
B
R
B
1.5V
where RA is the top resistor, and RB is the bottom resistor.
Power Good
The PGOOD pin is an open-drain pin that can be used to
monitor valid output voltage regulation. This pin monitors
a ±10% window around the regulation point, and tracks
with margining.
COMP Pin
The pin is the external compensation pin. The module has
already been internally compensated for most output volt-
ages. LTpowerCAD™ from Linear Technology is available
for more control loop optimization.
FCB Pin
The FCB pin determines whether the bottom MOSFET re-
mains on when current reverses in the inductor. Tying this
pin above its 0.6V threshold enables discontinuous operation
where the bottom MOSFET turns off when inductor current
reverses. FCB pin below the 0.6V threshold forces continu-
ous synchronous operation, allowing current to reverse
at light loads and maintaining high frequency operation.
PLLIN Pin
The power module has a phase-locked loop comprised
of an internal voltage controlled oscillator and a phase
detector. This allows the internal top MOSFET turn-on
to be locked to the rising edge of the external clock.
The frequency range is ±30% around the set operating
frequency. A pulse detection circuit is used to detect a
clock on the PLLIN pin to turn on the phase-locked loop.
The pulse width of the clock has to be at least 400ns. The
clock high level must be greater than 1.7V and clock low
level below 0.3V. During the start-up of the regulator, the
phase-locked loop function is disabled.
INTVCC and DRVCC Connection
An internal low dropout regulator produces an internal
5V supply that powers the control circuitry and DRVCC
for driving the internal power MOSFETs. Therefore, if
the system does not have a 5V power rail, the LTM4612
can be directly powered by VIN. The gate driver current
through the LDO is about 20mA. The internal LDO power
dissipation can be calculated as:
PLDO_LOSS = 20mA (VIN – 5V)
The LTM4612 also provides the external gate driver voltage
pin DRVCC. If there is a 5V rail in the system, it is recom-
mended to connect the DRVCC pin to the external 5V rail.
This is especially true for higher input voltages. Do not
apply more than 6V to the DRVCC pin.
APPLICATIONS INFORMATION
LTM4612
17
4612fc
For more information www.linear.com/LTM4612
Figure 8. Radiated Emission Scan with 24VIN to
5VOUT at 5A Measured in 10 Meter Chamber
FREQUENCY (MHz)
30
dBµV/m
30
70
128.1
226.2
324.3
10
60
20
0
–10
50
40
422.4
520.5
618.6
716.7
814.8
912.9
1010
EN55022 CLASS B LIMIT
4612 F08
APPLICATIONS INFORMATION
Parallel Operation
The LTM4612 device is an inherently current mode con-
trolled device. This allows the paralleled modules to have
very good current sharing and balanced thermal on the
design. Figure 21 shows a schematic of the parallel design.
The voltage feedback equation changes with the variable
N as modules are paralleled. The equation:
RFB =
100k
N
VOUT
0.6V
1
N is the number of paralleled modules.
Radiated EMI Noise
High radiated EMI noise is a disadvantage for switching
regulators by nature. Fast switching turn-on and turn-off
make the large di/dt change in the converters, which act
as the radiation sources in most systems. LTM4612 inte-
grates the feature to minimize the radiated EMI noise to
meet the most applications with low noise requirements.
An optimized gate driver for the MOSFET and a noise
cancellation network are installed inside the LTM4612
to achieve the low radiated EMI noise. Figure 8 shows a
typical example for the LTM4612 to meet the Class B of
EN55022 radiated emission limit.
Thermal Considerations and Output Current Derating
In different applications, LTM4612 operates in a variety
of thermal environments. The maximum output current is
limited by the environment thermal condition. Sufficient
cooling should be provided to help ensure reliable opera-
tion. When the cooling is limited, proper output current
derating is necessary, considering ambient temperature,
airflow, input/output condition, and the need for increased
reliability.
The power loss curves in Figures 9 and 10 can be used
in coordination with the load current derating curves in
Figures 11 to 16 for calculating an approximate θJA for
the module. Graph designation delineates between no
heat sink, and a BGA heat sink. Each of the load current
derating curves will lower the maximum load current as a
function of the increased ambient temperature to keep the
maximum junction temperature of the power module at
125°C maximum. This will maintain the maximum operat-
ing temperature below 125°C. Each of the derating curves
and the power loss curve that corresponds to the correct
output voltage can be used to solve for the approximate
θJA of the condition. Each figure has three curves that are
taken at three different air flow conditions. Each of the
derating curves in Figures 11 to 16 can be used with the
appropriate power loss curve in either Figure 9 or Figure
10 to derive an approximate θJA. Table 3 provides the ap-
proximate θJA for Figures 11 to 16. A complete explanation
of the thermal characteristics is provided in the thermal
application note, AN110.
LTM4612
18
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Figure 9. Power Loss at
12VOUT and 15VOUT
Figure 10. Power Loss at 5VOUT Figure 11. No Heat Sink
with 36VIN to 5VOUT
Figure 12. BGA Heat Sink
with 36VIN to 5VOUT
Figure 13. No Heat Sink
with 24VIN to 12VOUT
Figure 14. BGA Heat Sink
with 24VIN to 12VOUT
LOAD CURRENT (A)
0
POWER LOSS (W)
4
5
3
2
2 4
13 5
1
0
6
4612 F09
24VIN TO 12VOUT
36VIN TO 15VOUT
LOAD CURRENT (A)
0
POWER LOSS (W)
4
5
3
2
2 4
13 5
1
0
6
4612 F10
36VIN TO 5VOUT
AMBIENT TEMPERATURE (°C)
25
0
LOAD CURRENT (A)
1.0
2.0
3.0
35 45 55 65 8575 95
4.0
5.0
0.5
1.5
2.5
3.5
4.5
105
4612 F11
0LFM 400LFM
200
LFM
AMBIENT TEMPERATURE (°C)
25
0
LOAD CURRENT (A)
1.0
2.0
3.0
35 45 55 65 8575 95
4.0
5.0
0.5
1.5
2.5
3.5
4.5
105
4612 F12
0LFM 400LFM
200
LFM
AMBIENT TEMPERATURE (°C)
25
0
LOAD CURRENT (A)
1.0
2.0
3.0
35 45 55 65 8575 95
4.0
5.0
0.5
1.5
2.5
3.5
4.5
105
4612 F13
0LFM 400LFM
200
LFM
AMBIENT TEMPERATURE (°C)
25
0
LOAD CURRENT (A)
1.0
2.0
3.0
35 45 55 65 8575 95
4.0
5.0
0.5
1.5
2.5
3.5
4.5
105
4612 F14
0LFM 400LFM
200
LFM
Figure 15. No Heat Sink
with 36VIN to 15VOUT
Figure 16. BGA Heat Sink
with 36VIN to 15VOUT
AMBIENT TEMPERATURE (°C)
25
0
LOAD CURRENT (A)
1.0
2.0
3.0
35 45 55 65 8575 95
4.0
5.0
0.5
1.5
2.5
3.5
4.5
4612 F15
0LFM 400LFM
200LFM
AMBIENT TEMPERATURE (°C)
25
0
LOAD CURRENT (A)
1.0
2.0
3.0
35 45 55 65 8575 95
4.0
5.0
0.5
1.5
2.5
3.5
4.5
4612 F16
0LFM 400LFM
200LFM
LTM4612
19
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Table 3. 12V and 15V Outputs
DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W)
Figures 11, 13, 15 24, 36 Figure 9 0 None 13
Figures 11, 13, 15 24, 36 Figure 9 200 None 9.3
Figures 11, 13, 15 24, 36 Figure 9 400 None 8.3
Figures 12, 14, 16 24, 36 Figure 9 0 BGA Heat Sink 12.2
Figures 12, 14, 16 24, 36 Figure 9 200 BGA Heat Sink 8.6
Figures 12, 14, 16 24, 36 Figure 9 400 BGA Heat Sink 7.7
Table 4. 5V Output
DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W)
Figure 11 36 Figure 10 0 None 14.9
Figure 11 36 Figure 10 200 None 11.1
Figure 11 36 Figure 10 400 None 10
Figure 12 36 Figure 10 0 BGA Heat Sink 14
Figure 12 36 Figure 10 200 BGA Heat Sink 10.4
Figure 12 36 Figure 10 400 BGA Heat Sink 9.3
Heat Sink Manufacturer
Wakefield Engineering Part No: LTN20069 Phone: 603-635-2800
LTM4612
20
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Safety Considerations
The LTM4612 modules do not provide isolation from VIN
to VOUT. There is no internal fuse. If required, a slow blow
fuse with a rating twice the maximum input current needs
to be provided to protect each unit from catastrophic
failure.
Layout Checklist/Example
The high integration of LTM4612 makes the PCB board
layout very simple and easy. However, to optimize its
electrical and thermal performance, some layout consid-
erations are still necessary.
Use large PCB copper areas for high current path, in-
cluding VIN, PGND and VOUT. It helps to minimize the
PCB conduction loss and thermal stress.
Place high frequency ceramic input and output capaci-
tors next to the VD, PGND and VOUT pins to minimize
high frequency noise.
Place a dedicated power ground layer underneath the
unit.
Use round corners for the PCB copper layer to minimize
the radiated noise.
To minimize the EMI noise and reduce module thermal
stress, use multiple vias for interconnection between
top layer and other power layers.
Do not put vias directly on pads.
If vias are placed onto the pads, the the vias must be
capped.
Interstitial via placement can also be used if necessary.
Use a separated SGND ground copper area for com-
ponents connected to signal pins. Connect the SGND
to PGND underneath the unit.
Place one or more high frequency ceramic capacitors
close to the connection into the system board.
Figure 17 gives a good example of the recommended
layout.
Figure 17. Recommended PCB Layout
SIGNAL
GND
VOUT
VIN
GND
COUT
CIN CIN
COUT
4612 F17
LTM4612
21
4612fc
For more information www.linear.com/LTM4612
APPLICATIONS INFORMATION
Figure 19. Typical 5V to 36VIN, 3.3V at 5A Design with 400kHz Frequency
Figure 18. Typical 22V to 36VIN, 12V at 5A Design
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
FCB
MARG0
MARG1
MPGM
VOUT
VFB
PULL-UP SUPPLY ≤ 5V
R3
100k
C4
0.01µF
C3
22pF COUT1
22µF
6.3V
COUT2
220µF
6.3V
CIN
10µF
50V CERAMIC
VIN
5V TO 36V
CLOCK SYNC
REFER TO TABLE 2
EXTERNAL 5V SUPPLY
IMPROVES EFFICIENCY—
ESPECIALLY FOR HIGH
INPUT VOLTAGES
ON/OFF LTM4612
SGND PGND
MARGIN
CONTROL
R4
100k
RfSET
191k
1%
RFB
22.1k
R1
392k
5% MARGIN
+
4612 F19
VDVIN PLLIN
C1
10µF
50V
VOUT
3.3V
5A
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
FCB
MARG0
MARG1
MPGM
VOUT
VFB
PULL-UP SUPPLY ≤ 5V
R3
100k
C4
0.01µF
C3
22pF COUT1
22µF
16V
COUT2
220µF
16V
CIN
10µF
50V CERAMIC
VIN
22V TO 36V
CLOCK SYNC
REFER TO TABLE 2
ON/OFF LTM4612
SGND PGND
MARGIN
CONTROL
R4
100k
RFB
5.23k
R1
392k
5% MARGIN
+
4612 F18
VDVIN PLLIN
C1
10µF
50V
R5
2M VOUT
12V
5A
LTM4612
22
4612fc
For more information www.linear.com/LTM4612
Figure 21. 2-Phase, Parallel 12V at 10A Design
Figure 20. 26V to 36VIN, 15V at 4A Design with Reduced Frequency
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
FCB
MARG0
MARG1
MPGM
VOUT
VFB
PULL-UP SUPPLY ≤ 5V
R3
100k
C4
0.01µF
C3
22pF COUT1
22µF
16V
COUT2
220µF
16V
CIN
10µF
50V
CERAMIC
VIN
26V TO 36V
CLOCK SYNC
ON/OFF LTM4612
SGND PGND
MARGIN
CONTROL
R4
100k
RFB
4.12k
RfSET
806k, 1%
R1
392k
5% MARGIN
+
4612 F20
VDVIN PLLIN
C1
10µF
50V
VOUT
15V
4A
APPLICATIONS INFORMATION
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
VOUT
VFB
FCB
MARG0
MARG1
MPGM
PULL-UP SUPPLY ≤ 5V
R2
100k
C7
0.33µF
C6
47pF C3
22µF
16V
4612 F21
C4
220µF
16V
C11
0.1µF
C5
100µF
50V
C2
10µF
50V
C8
10µF
50V
VIN
20V TO 36V
LTC6908-1
2-PHASE
OSCILLATOR
CLOCK SYNC
0° PHASE
CLOCK SYNC
180° PHASE
LTM4612
SGND PGND
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
LTM4612
SGND PGND
MARGIN
CONTROL
5% MARGIN
R4
100k
RFB
2.61k
R1
392k
R5
124k
V+
GND
SET
OUT1
OUT2
MOD
+
VOUT
VFB
FCB
MARG0
MARG1
MPGM
C9
22µF
16V
C10
220µF
16V
R6
392k
+
+
RFB = 100k/N
VOUT
0.6V – 1
VDVIN PLLIN
C1
10µF
50V
VDVIN PLLIN
C11
10µF
50V
VOUT
12V, 10A
LTM4612
23
4612fc
For more information www.linear.com/LTM4612
Figure 22. 2-Phase, 12V and 10V at 5A Design
APPLICATIONS INFORMATION
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
VOUT
VFB
FCB
MARG0
MARG1
MPGM
PULL-UP SUPPLY ≤ 5V
R2
100k
C7
0.15µF
C6
22pF C3
22µF
16V
4612 F22
C4
220µF
16V
12V AT 5A
C11
0.1µF
C5
100µF
50V
C2
10µF
50V
C8
10µF
50V
VIN
22V TO 36V
LTC6908-1
2-PHASE
OSCILLATOR
CLOCK SYNC
0° PHASE
CLOCK SYNC
180° PHASE
LTM4612
SGND PGND
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
LTM4612
SGND
12V TRACK
PGND
MARGIN
CONTROL
5% MARGIN
R4
100k
RFB1
5.23k
RFB2
6.34k
R1
392k
R8
100k
R9
6.34k
R3
100k
R7
100k
PULL-UP SUPPLY ≤ 5V
R5
118k
V+
GND
SET
OUT1
OUT2
MOD
+
VOUT
VFB
FCB
MARG0
MARG1
MPGM
C1
22pF C9
22µF
16V
C10
220µF
16V
10V AT 5A
MARGIN
CONTROL
R6
392k
+
+
VDVIN PLLIN
C1
10µF
50V
VDVIN PLLIN
C11
10µF
50V
LTM4612
24
4612fc
For more information www.linear.com/LTM4612
DRVCC
fSET
TRACK/SS
PGOOD
RUN
COMP
INTVCC
FCB
MARG0
MARG1
MPGM
VOUT
VFB
VDVIN
5V
R2
100k
C7
0.15µF
C6
22pF C3
22µF
6.3V
4612 F23
C4
220µF
6.3V
5V AT 5A
C11
0.1µF
C5
100µF
50V
C2
10µF
50V
C8
10µF
50V
VIN
7V TO 36V
LTC6908-1
2-PHASE
OSCILLATOR
PLLIN
CLOCK SYNC
0° PHASE
CLOCK SYNC
180° PHASE
SGND PGND
PGOOD
RUN
COMP
INTVCC
DRVCC
fSET
TRACK/SS
VIN
VDPLLIN
SGND
5V TRACK
PGND
MARGIN
CONTROL
R4
100k
RfSET1
150k RFB1
13.7k
R1
392k
R8
100k
R9
22.1k
RfSET2
100k
R3
100k
R7
100k
3.3V
R5
200k
V+
GND
SET
OUT1
OUT2
MOD
+
VOUT
VFB
FCB
MARG0
MARG1
MPGM
C1
22pF C9
22µF
6.3V
C10
220µF
6.3V
3.3V AT 5A
MARGIN
CONTROL
RFB2
22.1k
R6
392k
+
+
LTM4612
LTM4612
5% MARGIN
C1
10µF
50V
C11
10µF
50V
Figure 23. 2-Phase, 5V and 3.3V at 5A Design with 500kHz Frequency
APPLICATIONS INFORMATION
LTM4612
25
4612fc
For more information www.linear.com/LTM4612
PIN NAME
A1
A2
A3
A4
A5
A6
VIN
VIN
VIN
VIN
VIN
VIN
B1
B2
B3
B4
B5
B6
VIN
VIN
VIN
VIN
VIN
VIN
C1
C2
C3
C4
C5
C6
VIN
VIN
VIN
VIN
VIN
VIN
Pin Assignment Tables
(Arranged by Pin Function)
PIN NAME
D1
D2
D3
D4
D5
D6
PGND
PGND
PGND
PGND
PGND
PGND
E1
E2
E3
E4
E5
E6
E7
E8
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
F1
F2
F3
F4
F5
F6
F7
F8
F9
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PIN NAME
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
J11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
L11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
PIN NAME
A7
A8
A9
A10
A11
A12
INTVCC
PLLIN
TRACK/SS
RUN
COMP
MPGM
B7
B8
B9
B10
B11
B12
VD
-
RUN
-
MPGM
fSET
C7
C8
C9
C10
C11
C12
VD
-
-
DRVCC
MARG1
MARG0
D7
D8
D9
D10
D11
D12
-
-
SGND
-
COMP
MARG1
E9
E10
E11
E12
-
-
DRVCC
DRVCC
F10
F11
F12
-
-
VFB
G12 PGOOD
H12 SGND
J12 NC
K12 NC
L12 NC
M12 FCB
PACKAGE DESCRIPTION
LTM4612
26
4612fc
For more information www.linear.com/LTM4612
PACKAGE DESCRIPTION
L K J H G F E D C BM A
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
2. ALL DIMENSIONS ARE IN MILLIMETERS
LAND DESIGNATION PER JESD MO-222, SPP-010
5. PRIMARY DATUM -Z- IS SEATING PLANE
6. THE TOTAL NUMBER OF PADS: 133
4
3
DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
SYMBOL
aaa
bbb
eee
TOLERANCE
0.10
0.10
0.05
2.72 – 2.92
DETAIL B
DETAIL B
SUBSTRATE
MOLD
CAP
0.27 – 0.37
2.45 – 2.55
bbb Z
Z
15
BSC
PACKAGE TOP VIEW
15
BSC
4
PAD 1
CORNER
XY
aaa Z
aaa Z
DETAIL A
13.97
BSC
1.27
BSC
13.97
BSC
0.12 – 0.28
PACKAGE BOTTOM VIEW
C(0.30)
PAD 1
3
PADS
SEE NOTES
1
2
3
4
5
6
7
8
10
9
11
12
DETAIL A
0.630 ±0.025 SQ. 133x
SYXeee
SUGGESTED PCB LAYOUT
TOP VIEW
0.0000
0.6350
0.6350
1.9050
1.9050
3.1750
3.1750
4.4450
4.4450
5.7150
5.7150
6.9850
6.9850
6.9850
5.7150
5.7150
4.4450
4.4450
3.1750
3.1750
1.9050
1.9050
0.6350
0.6350
0.0000
6.9850
LGA 133 1212 REV A
LTMXXXXXX
µModule
TRAY PIN 1
BEVEL PACKAGE IN TRAY LOADING ORIENTATION
COMPONENT
PIN “A1”
LGA Package
133-Lead (15mm × 15mm × 2.82mm)
(Reference LTC DWG # 05-08-1766 Rev A)
7 PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY
!
7
SEE NOTES
Please refer to http://www.linear.com/product/LTM4612#packaging for the most recent package drawings.
LTM4612
27
4612fc
For more information www.linear.com/LTM4612
REVISION HISTORY
REV DATE DESCRIPTION PAGE NUMBER
A 03/10 Changes to Title and Description
Changes to Absolute Maximum Ratings
Changes to Electrical Characteristics
Text Changes to Operation Section
Text Changes to Applications Information Section
Changes to Figures 18, 19, 20, 21, 22
Changes to Related Parts
1
1
2, 3
10
12, 14
19, 20, 21, 22
26
B 05/11 Changes to the Title, Description, Features and Typical Application sections.
Changes to “The l denotes...” statement and Note 2.
Changes to the Pin Functions.
Changes to the Block Diagram.
Text changes to the Operation section.
Text changes to the Applications Information section.
Changes to Figures 17, 19, 21, 22.
Changes to the Related Parts.
1
2, 3, 4
7, 8
9
10
10–20
20, 21, 22, 23
28
C 09/16 Changed Max value of VINTVCC from 5.3V to 5.5V 3
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
LTM4612
28
4612fc
For more information www.linear.com/LTM4612
RELATED PARTS
PACKAGE PHOTOGRAPH
4612 F24
15mm
15mm
2.8mm
PART NUMBER DESCRIPTION COMMENTS
LTM4606 EN55022B Compliant 6A, DC/DC µModule
Regulator
EN55022B Compliant with PLL, Output Tracking and Margining,
LTM4612 Pin Compatible
LTM4613 EN55022B Compliant 36V
, 8A, Step-Down µModule
Regulator with PLL, Output Tracking
5V ≤ VIN ≤ 36V, 3.3V ≤ VOUT ≤ 15V, 15mm × 15mm × 4.3mm LGA Package
LTM4601/LTM4601A 12A DC/DC µModule Regulator with PLL, Output
Tracking/Margining and Remote Sensing
Synchronizable, PolyPhase Operation, LTM4601-1/LTM4601A-1 Version Has
No Remote Sensing, LGA Package
LTM4604A Low VIN 4A DC/DC µModule Regulator 2.375V ≤ VIN ≤ 5.5V, 0.8V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.3mm LGA Package
LTM4608A Low VIN 8A DC/DC µModule Regulator 2.7V ≤ VIN ≤ 5.5V, 0.6V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.8mm LGA Package
LTM8022/LTM8023 36VIN, 1A and 2A DC/DC µModule Regulator Pin Compatible, 4.5V ≤ VIN ≤ 36V; 9mm × 11.25mm × 2.8mm LGA Package
LTM4627 20VIN, 15A DC/DC Step-Down µModule Regulator 4.5V ≤ VIN ≤ 20V, 0.6V ≤ VOUT ≤ 5V, 15mm × 15mm × 4.3mm LGA Package
LTM4618 26VIN, 6A DC/DC Step-Down µModule Regulator
with PLL, Output Tracking
4.5V ≤ VIN ≤ 26.5V, 0.8V ≤ VOUT ≤ 5V, Synchronizable,
9mm × 15mm × 4.3mm LGA Package
LTM8033 EN55022B Compliant 36VIN, 3A DC/DC Step-Down
µModule Regulator
3.6V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 24V, Synchronizable,
11.25mm × 15mm × 4.3mm LGA Package
DESIGN RESOURCES
SUBJECT DESCRIPTION
µModule Design and Manufacturing Resources Design:
Selector Guides
Demo Boards and Gerber Files
Free Simulation Tools
Manufacturing:
Quick Start Guide
PCB Design, Assembly and Manufacturing Guidelines
Package and Board Level Reliability
µModule Regulator Products Search 1. Sort table of products by parameters and download the result as a spread sheet.
2. Search using the Quick Power Search parametric table.
TechClip Videos Quick videos detailing how to bench test electrical and thermal performance of µModule products.
Digital Power System Management Linear Technologys family of digital power supply management ICs are highly integrated solutions that
offer essential functions, including power supply monitoring, supervision, margining and sequencing,
and feature EEPROM for storing user configurations and fault logging.
LINEAR TECHNOLOGY CORPORATION 2008
LT 0916 REV C • PRINTED IN USA
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTM4612