Cat.No.C02E-16
Chip Monolithic
Ceramic Capacitors
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please check the MURATA home page (http://www.murata.com/) if you cannot find the part number in the catalog.
(Part Number)
w
qProduct ID
wSeries
Chip Monolithic Ceramic Capacitors
GR
GQ
GM
GN
LL
GJ
GA
J
M
4
7
M
A
D
M
L
R
A
M
M
2
3
Soft Termination Type
Tin Plated Layer
Only for Information Devices / Tip & Ring
Only for Camera Flash Circuit
High Frequency for
Flow/Reflow Soldering
Monolithic Microchip
For Bonding
Capacitor Array
Low ESL Type
Controlled ESR Low ESL Type
8-termination Low ESL Type
10-termination Low ESL Type
High Frequency Low Loss Type
For AC250V (r.m.s.)
Safety Standard Certified Type
Product ID Code Series
GR
q
M
e
18
r
8
t
B1
y
1H
u
102
i
K
o
A01
eDimensions (LgW)
!0
D
Code
0.4g0.2mm
0.6g0.3mm
0.5g0.5mm
0.8g0.8mm
0.38g0.38mm
0.9g0.6mm
1.0g0.5mm
1.6g0.8mm
1.37g1.0mm
2.0g1.25mm
2.8g2.8mm
3.2g1.6mm
3.2g2.5mm
4.5g2.0mm
4.5g3.2mm
5.7g2.8mm
5.7g5.0mm
Dimensions (LgW)
01005
0201
0202
0303
015015
0302
0402
0603
0504
0805
1111
1206
1210
1808
1812
2211
2220
EIA
02
03
05
08
0D
0M
15
18
1M
21
22
31
32
42
43
52
55
A
B
C
D
E
F
M
N
Q
R
S
X
1.0mm
1.25mm
1.6mm
2.0mm
2.5mm
3.2mm
1.15mm
1.35mm
1.5mm
1.8mm
2.8mm
Depends on individual standards.
rDimension (T) (Except GNM)
Code
2
3
5
6
7
8
9
0.2mm
0.3mm
0.5mm
0.6mm
0.7mm
0.8mm
0.85mm
Dimension (T)
rElements (GNM Only)
Code
2
4
2-elements
4-elements
Elements
Continued on the following page.
o Part Numberingo Part Numbering
2
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please check the MURATA home page (http://www.murata.com/) if you cannot find the part number in the catalog.
Continued from the preceding page.
Continued on the following page.
25 to 85°C
25 to 85°C
25 to 85°C
25 to 125°C *6
-25 to 85°C
-25 to 85°C
-55 to 125°C
-55 to 105°C
-220±60ppm/°C
-330±60ppm/°C
-470±60ppm/°C
-750±120ppm/°C
±10%
±10%
±22%
±22%
R2H *1
S2H *1
T2H *1
U2J *1
B *2
B
X7S
X6S
6R
6S
6T
7U
B1
B3
C7
C8
-55 to 125°C
-55 to 125°C
-55 to 125°C
-55 to 125°C
-25 to 85°C
-25 to 85°C
-55 to 125°C
-55 to 105°C
tTemperature Characteristics
Code
Temperature Characteristic Codes Temperature Characteristics
20 to 85°C
20 to 125°C
20 to 85°C
20 to 85°C
20 to 85°C
20 to 85°C
20 to 125°C
20 to 85°C
20 to 85°C
20 to 85°C
20 to 85°C
20 to 85°C
20 to 125°C
25 to 125°C
25 to 150°C
25 to 125°C
25 to 85°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
20°C
25°C
25°C
25°C
25°C
Temperature
Range
Reference
Temperature
+350 to -1000ppm/°C
0±60ppm/°C
-150±60ppm/°C
-220±60ppm/°C
-330±60ppm/°C
-470±60ppm/°C
0±120ppm/°C
-150±120ppm/°C
-220±120ppm/°C
-330±120ppm/°C
-470±120ppm/°C
-750±120ppm/°C
0±250ppm/°C
0±30ppm/°C
0±30ppm/°C
0±60ppm/°C
-150±60ppm/°C
Capacitance Change or
Temperature Coefficient
SL *1
CH *1
PH *1
RH *1
SH *1
TH *1
CJ *1
PJ *1
RJ *1
SJ *1
TJ *1
UJ *1
CK *1
C0G *1
X8G *1
C0H *1
P2H *1
JIS
JIS
JIS
JIS
JIS
JIS
JIS
JIS
JIS
JIS
JIS
JIS
JIS
EIA
EIA
EIA
EIA
25°C
25°C
25°C
25°C
20°C
20°C
25°C
25°C
EIA
EIA
EIA
EIA
JIS
JIS
EIA
EIA
-25 to 85°C
-30 to 85°C
-55 to 150°C
-55 to 125°C
-55 to 125°C
-55 to 85°C
-55 to 125°C
-55 to 150°C
-55 to 125°C
+30, -80%
+22, -82%
+15, -40%
±15%
±15%
±15%
±15%
±15%
±10% *4
+22, -33% *5
F *2
Y5V
X8L
R *2
R
X5R
X7R
X8R
-
F1
F5
L8
R1
R3
R6
R7
R9
W0
-25 to 85°C
-30 to 85°C
-55 to 150°C
-55 to 125°C
-55 to 125°C
-55 to 85°C
-55 to 125°C
-55 to 150°C
-55 to 125°C
20°C
25°C
25°C
20°C
20°C
25°C
25°C
25°C
25°C
JIS
EIA
*3
JIS
JIS
EIA
EIA
EIA
-
-55 to 125°C +22, -33%X7TD7 -55 to 125°C25°CEIA
-55 to 105°C +22, -33%X6TD8 -55 to 105°C25°CEIA
-55 to 125°C +22, -56%X7UE7 -55 to 125°C25°CEIA
Public STD Code
1X
2C
2P
2R
2S
2T
3C
3P
3R
3S
3T
3U
4C
5C
5G
6C
6P
-55 to 125°C
-55 to 125°C
-25 to 85°C
-25 to 85°C
-25 to 85°C
-25 to 85°C
-55 to 125°C
-25 to 85°C
-25 to 85°C
-25 to 85°C
-25 to 85°C
-25 to 85°C
-55 to 125°C
-55 to 125°C
-55 to 150°C
-55 to 125°C
-55 to 125°C
Operating
Temperature Range
*1 Please refer to table for Capacitance Change under reference temperature.
*2 Capacitance change is specified with 50% rated voltage applied.
*3 Murata Temperature Characteristic Code.
*4 Apply DC350V bias.
*5 No DC bias.
*6 Rated Voltage 100Vdc max : 25 to 85°C
3
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please check the MURATA home page (http://www.murata.com/) if you cannot find the part number in the catalog.
Continued from the preceding page.
Murata Code
Capacitance Change from 25°C (%)
–55°C –30°C –10°C
Max. Min. Max. Min. Max. Min.
5C/5G 0.58 –0.24 0.40 –0.17 0.25 –0.11
6C 0.87 –0.48 0.59 –0.33 0.38 –0.21
6P 2.33 0.72 1.61 0.50 1.02 0.32
6R 3.02 1.28 2.08 0.88 1.32 0.56
6S 4.09 2.16 2.81 1.49 1.79 0.95
6T 5.46 3.28 3.75 2.26 2.39 1.44
7U 8.78 5.04 6.04 3.47 3.84 2.21
EIA Code
4C 2.56 –1.88 1.54 –1.13 1.02 –0.75
3P – – 1.65 0.14 1.10 0.09
3R – – 2.03 0.45 1.35 0.30
3S – – 2.63 0.95 1.76 0.63
3T – – 3.40 1.58 2.27 1.05
3U – – 4.94 2.84 3.29 1.89
3C 1.37 –0.90 0.82 –0.54 0.55 –0.36
Murata Code
Capacitance Change from 20°C (%)
–55°C –25°C –10°C
Max. Min. Max. Min. Max. Min.
2C 0.82 –0.45 0.49 –0.27 0.33 –0.18
2P – – 1.32 0.41 0.88 0.27
2R – – 1.70 0.72 1.13 0.48
2S – – 2.30 1.22 1.54 0.81
2T – – 3.07 1.85 2.05 1.23
1X ––––––
oCapacitance Change from each temperature
JIS Code
uCapacitance
Expressed by three-digit alphanumerics. The unit is picofarad
(pF). The first and second figures are significant digits, and the
third figure expresses the number of zeros which follow the two
numbers.If there is a decimal point, it is expressed by the capital
letter "R." In this case, all figures are significant digits.
R50
1R0
100
103
Ex.)
0.5pF
1.0pF
10pF
10000pF
Code Capacitance
yRated Voltage
0E
0G
0J
1A
1C
1E
YA
1H
2A
2D
2E
YD
2H
2J
3A
3D
3F
BB
E2
GC
GF
GD
GB
DC2.5V
DC4V
DC6.3V
DC10V
DC16V
DC25V
DC35V
DC50V
DC100V
DC200V
DC250V
DC300V
DC500V
DC630V
DC1kV
DC2kV
DC3.15kV
DC350V (for Camera Flash Circuit)
AC250V
X1/Y2; AC250V (Safety Standard Certified Type GC)
Y2, X1/Y2; AC250V (Safety Standard Certified Type GF)
Y3; AC250V (Safety Standard Certified Type GD)
X2; AC250V (Safety Standard Certified Type GB)
Code Rated Voltage
Continued on the following page.
4
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please check the MURATA home page (http://www.murata.com/) if you cannot find the part number in the catalog.
Continued from the preceding page.
Expressed by three figures.
oIndividual Specification Code (Except LLR)
iCapacitance Tolerance
Code
WGRM/GJM
Series
C∆
TC
±0.05pF
Capacitance Tolerance
V9.9pF 0.1pF
B
GRM/GJM
GQM
C∆±0.1pF
V9.9pF
V1pF
1.1 to 9.9pF
0.1pF
0.1pF
1pF Step and E24 Series
C
GRM/GJM
GRM
GQM
C∆
except C∆
C∆
±0.25pF
V9.9pF
V5pF
V1pF
1.1 to 9.9pF
0.1pF
* 1pF
0.1pF
1pF Step and E24 Series
D
GRM/GJM
GRM
GQM
C∆
except C∆
C∆
±0.5pF
5.1 to 9.9pF
5.1 to 9.9pF
5.1 to 9.9pF
0.1pF
* 1pF
1pF Step and E24 Series
GGJM
GQM
C∆
C∆
±2% U10pF
U10pF E12 Series
E24 Series
JGRM/GA3
GQM/GJM
C∆, SL, U2J
C∆
±5% U10pF
U10pF E12 Series
E24 Series
Capacitance Step
K
GRJ/GRM/GR7/GA3
GNM
GR4, GMD
B, R, X7R, X5R, ZLM
C0G
B, R, X7R, X5R, ZLM
±10% E6 Series
E6 Series
E12 Series
M
GRM/GMA
GNM
GA2
LLL/LLR/LLA/LLM
B, R, X7R, X7S
X5R, X7R, X7S
X7R
X5R, X7R, X7S, X6S
±20%
E6 Series
E3 Series
E3 Series
E3 Series
ZGRM
F, Y5V+80%, -20% E3 Series
RDepends on individual standards.
* E24 series is also available.
oESR (LLR Only)
Code
E01
E03
E05
E07
100mΩ
220mΩ
470mΩ
1000mΩ
ESR
!0Packaging
Code
L
D
E
K
J
F
B
C
T
ø180mm Embossed Taping
ø180mm Paper Taping
ø180mm Paper Taping (LLL15)
ø330mm Embossed Taping
ø330mm Paper Taping
ø330mm Paper Taping (LLL15)
Bulk
Bulk Case
Bulk Tray
Packaging
5
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
64
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Chip Monolithic Ceramic Capacitors
Capacitor Array GNM Series
■ Features
1. High density mounting due to mounting space saving
2. Mounting cost saving
■ Applications
General electronic equipment
LW
T
P
GNM214/314
Part Number Dimensions (mm)
GNM214
GNM314
L
2.0 ±0.15
3.2 ±0.15
P
0.5 ±0.05
0.8 ±0.1
T
0.5 +0.05/-0.1
0.6 ±0.1
0.85 ±0.1
0.8 ±0.1
0.85 ±0.1
1.0 ±0.1
1.15 ±0.1
W
1.25 ±0.15
1.6 ±0.15
LW
T
P
GNM0M2/1M2/212
Part Number L
GNM0M2 0.9 ±0.05 P
0.45 ±0.05
T
Dimensions (mm)
0.45 ±0.05
W
0.6 ±0.05
GNM1M2 1.37 ±0.15 0.64 ±0.05
0.5 +0.05/-0.10
1.0 ±0.15 0.6 ±0.1
0.8 +0/-0.15
GNM212 2.0 ±0.15 1.0 ±0.1
0.6 ±0.1
1.25 ±0.15 0.85 ±0.1
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
65
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Capacitance Table
Temperature Compensating Type C0G(5C) Characteristics
1.37x1.0
(1M)
<0504>
50
(1H)
2.0x1.25
(21)
<0805>
50
(1H)
3.2x1.6
(31)
<1206>
100
(2A)50
(1H)
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
2(2)4(4)
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.6 ex.0.6: T Dimension [mm]
LxW
[mm]
Rated Voltage
[Vdc]
Capacitance
10pF(100)
15pF(150)
22pF(220)
33pF(330)
47pF(470)
68pF(680)
100pF(101)
150pF(151)
220pF(221)
330pF(331)
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
Number of Elements
High Dielectric Constant Type X7R(R7)/X7S(C7) Characteristics
50
(1H)
0.6
25
(1E)
0.6
0.6
0.6
1.37x1.0
(1M)
<0504>
16
(1C)
0.6
0.6
0.6
0.6
0.6
0.6
10
(1A)50
(1H)
0.6
0.6
2.0x1.25
(21)
<0805>
25
(1E)
0.6
0.6
0.6
16
(1C)
0.85
0.85
0.85
50
(1H)
0.85
0.85
2(2)4(4)
3.2x1.6
(31)
<1206>
25
(1E)
0.85
16
(1C)
1.0
1.0
6.3
(0J)
1.15
0.6 ex.0.6: T Dimension [mm]
LxW
[mm]
Rated Voltage
[Vdc]
Capacitance
Number of Elements
470pF(471)
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
47000pF(473)
0.10µF(104)
1.0µF(105)
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
High Dielectric Constant Type X7R(R7) Characteristics-Low Profile
16
(1C)
0.5
16
(1C)
0.5
1.37x1.0
(1M)
<0504>
2.0x1.25
(21)
<0805>
2(2)4(4)
0.5 ex.0.5: T Dimension [mm]
LxW
[mm]
Rated Voltage
[Vdc]
Capacitance
Number of Elements
0.10µF(104)
The part number code is shown in ( ) and Unit is shown in [ ].
< >: EIA [inch] Code
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Capacitance Table
66
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
High Dielectric Constant Type X5R(R6) Characteristics
16
(1C)
0.45
0.45
0.45
0.45
10
(1A)
0.45
0.45
0.45
0.45
0.9x0.6
(0M)
<0302>
1.37x1.0
(1M)
<0504>
6.3
(0J)
0.45
0.45
0.45
0.45
0.45
4
(0G)50
(1H)
0.6
25
(1E)
0.6
0.6
0.6
2.0x1.25
(21)
<0805>
2.0x1.25
(21)
<0805>
16
(1C)10
(1A)
0.6
0.6
0.6
0.8
0.8
6.3
(0J)
0.8
0.8
2(2)4(4)
3.2x1.6
(31)
<1206>
16
(1C)
0.85
0.85
10
(1A)
0.85
0.85
6.3
(0J)10
(1A)6.3
(0J)16
(1C)10
(1A)
0.85
0.85 0.85 0.85
0.6 ex.0.6: T Dimension [mm]
LxW
[mm]
Rated Voltage
[Vdc]
Capacitance
Number of Elements
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
47000pF(473)
0.10µF(104)
0.22µF(224)
0.47µF(474)
1.0µF(105)
2.2µF(225)
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
0.6
0.6
0.8
0.8 0.85
0.85
High Dielectric Constant Type X5R(R6) Characteristics-Low Profile
16
(1C)10
(1A)
0.5
10
(1A)
0.5 0.5
1.37x1.0
(1M)
<0504>
2.0x1.25
(21)
<0805>
2(2)4(4)
0.5 ex.0.5: T Dimension [mm]
LxW
[mm]
Rated Voltage
[Vdc]
Capacitance
Number of Elements
1.0µF(105)
The part number code is shown in ( ) and Unit is shown in [ ].
< >: EIA [inch] Code
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
67
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
LxW [mm]
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
50(1H) 50(1H) 100(2A) 50(1H)
GNM1M25C1H100KD01D
GNM1M25C1H150KD01D
GNM1M25C1H220KD01D
GNM1M25C1H330KD01D
GNM1M25C1H470KD01D
GNM1M25C1H680KD01D
GNM1M25C1H101KD01D
GNM1M25C1H151KD01D
GNM1M25C1H221KD01D
GNM2145C1H100KD01D
GNM2145C1H150KD01D
GNM2145C1H220KD01D
GNM2145C1H330KD01D
GNM2145C1H470KD01D
GNM2145C1H680KD01D
GNM2145C1H101KD01D
GNM2145C1H151KD01D
GNM2145C1H221KD01D
GNM3145C2A100KD01D
GNM3145C2A150KD01D
GNM3145C2A220KD01D
GNM3145C2A330KD01D
GNM3145C2A470KD01D
GNM3145C2A680KD01D
GNM3145C2A101KD01D
GNM3145C2A151KD01D
GNM3145C1H100KD01D
GNM3145C1H150KD01D
GNM3145C1H220KD01D
GNM3145C1H330KD01D
GNM3145C1H470KD01D
GNM3145C1H680KD01D
GNM3145C1H101KD01D
GNM3145C1H151KD01D
GNM3145C1H221KD01D
GNM3145C1H331KD01D
1.37x1.0(1M)<0504> 2.0x1.25(21)<0805>
Number of Elements 2(2)4(4)
3.2x1.6(31)<1206>
10pF(100)
15pF(150)
22pF(220)
33pF(330)
47pF(470)
68pF(680)
100pF(101)
150pF(151)
220pF(221)
330pF(331)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
±10%(K)
Temperature Compensating Type C0G(5C) Characteristics
LxW [mm]
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
50(1H)
Number of Elements 2(2)
25(1E) 16(1C)
GNM1M2R71H102MA01D
GNM1M2R71E222MA01D
GNM1M2R71E472MA01D
GNM1M2R71E103MA01D
GNM1M2R71C223MA01D
GNM1M2R71C473MA01D
GNM1M2R71C104MA01D
1.37x1.0(1M)<0504>
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
47000pF(473)
0.10µF(104)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
LxW [mm]
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
50(1H)
Number of Elements 4(4)
25(1E) 16(1C)
GNM214R71H471MA01D
GNM214R71H102MA01D
GNM214R71E222MA01D
GNM214R71E472MA01D
GNM214R71E103MA01D
GNM214R71C223MA01D
GNM214R71C473MA01D
GNM214R71C104MA01D
2.0x1.25(21)<0805>
470pF(471)
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
47000pF(473)
0.10µF(104)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
10(1A)
GNM1M2R71A223MA01D
GNM1M2R71A473MA01D
GNM1M2C71A104MA01D
LxW [mm]
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
50(1H)
Number of Elements 4(4)
25(1E) 16(1C) 6.3(0J)
GNM314R71H473MA11D
GNM314R71H104MA11D GNM314R71E104MA11D
GNM314R71C473MA01L
GNM314R71C104MA01L
GNM314R70J105MA01L
3.2x1.6(31)<1206>
47000pF(473)
0.10µF(104)
1.0µF(105)
±20%(M)
±20%(M)
±20%(M)
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
* Please refer to GNM series Specifications and Test Method (2).
High Dielectric Constant Type X7R(R7)/X7S(C7) Characteristics
GN M 1M 2 5C 1H 100 K D01 D
Packaging Code in Part Number shows STD 180mm Reel Taping.
qProduct ID wSeries eDimensions (LxW) rNumber of Elements
tTemperature Characteristics yRated Voltage uCapacitance
iCapacitance Tolerance oIndividual Specification Code !0Packaging
(Part Number)
wq e r t y u i o !0
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
68
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
* Please refer to GNM series Specifications and Test Method (2).
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
LxW [mm]
Rated Volt. [Vdc]
Number of Elements
Capacitance Tolerance Part Number
16(1C) 10(1A) 6.3(0J)4(0G)
GNM0M2R61C103ME18D*
GNM0M2R61C223ME18D*
GNM0M2R61C473ME18D*
GNM0M2R61C104ME18D*
GNM0M2R61A103ME17D*
GNM0M2R61A223ME17D*
GNM0M2R61A473ME17D*
GNM0M2R61A104ME17D*
GNM0M2R60J103ME17D*
GNM0M2R60J223ME17D*
GNM0M2R60J473ME17D*
GNM0M2R60J104ME17D*
GNM0M2R60G105ME17D*
2(2)
0.9x0.6(0M)<0302>
10000pF(103)
22000pF(223)
47000pF(473)
0.10µF(104)
1.0µF(105)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
LxW [mm]
Rated Volt. [Vdc]
Number of Elements
Capacitance Tolerance Part Number
10(1A) 6.3(0J)
GNM1M2R61A223MA01D
GNM1M2R61A473MA01D
GNM1M2R61A104MA01D
GNM1M2R61A105ME17D*
GNM1M2R61A225ME18D*
GNM1M2R60J105ME12D*
GNM1M2R60J225ME18D*
1.37x1.0(1M)<0504>
2(2)
22000pF(223)
47000pF(473)
0.10µF(104)
1.0µF(105)
2.2µF(225)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
LxW [mm]
Rated Volt. [Vdc]
Number of Elements
Capacitance Tolerance Part Number
16(1C) 10(1A) 6.3(0J)
GNM212R61C474MA16D
GNM212R61C105MA16D GNM212R61A105MA13D
GNM212R61A225ME16D* GNM212R60J225ME16D*
2.0x1.25(21)<0805>
2(2)
0.47µF(474)
1.0µF(105)
2.2µF(225)
±20%(M)
±20%(M)
±20%(M)
LxW [mm]
Rated Volt. [Vdc]
Number of Elements
Capacitance Tolerance Part Number
50(1H) 25(1E) 16(1C)
GNM1M2R61H102MA01D
GNM1M2R61E222MA01D
GNM1M2R61E472MA01D
GNM1M2R61E103MA01D
GNM1M2R61C223MA01D
GNM1M2R61C473MA01D
GNM1M2R61C224ME18D*
GNM1M2R61C105ME18D*
1.37x1.0(1M)<0504>
2(2)
1000pF(102)
2200pF(222)
4700pF(472)
10000pF(103)
22000pF(223)
47000pF(473)
0.22µF(224)
1.0µF(105)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
±20%(M)
High Dielectric Constant Type X5R(R6) Characteristics
LxW [mm]
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
16(1C) 16(1C)
GNM1M2R71C104MAA1D GNM214R71C104MAA1D
1.37x1.0(1M)<0504>
Number of Elements 2(2)2.0x1.25(21)<0805>
4(4)
0.10µF(104)±20%(M)
High Dielectric Constant Type X7R(R7) Characteristics-Low Profile
GN M 1M 2 R7 1C 104 M AA1 D
Packaging Code in Part Number shows STD 180mm Reel Taping.
qProduct ID wSeries eDimensions (LxW) rNumber of Elements
tTemperature Characteristics yRated Voltage uCapacitance
iCapacitance Tolerance oIndividual Specification Code !0Packaging
(Part Number)
wq e r t y u i o !0
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
69
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
* Please refer to GNM series Specifications and Test Method (2).
LxW [mm]
Number of Elements
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
10(1A) 6.3(0J)
2.0x1.25(21)<0805>
4(4)
1.0µF(105)
2.2µF(225)
±20%(M)
±20%(M)
LxW [mm]
Number of Elements
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
16(1C) 10(1A)
GNM314R61C105MA15D
GNM214R61A105ME17D* GNM214R60J105ME17D*
GNM214R60J225ME18D*
GNM314R61A105MA13D
3.2x1.6(31)<1206>
4(4)
1.0µF(105)±20%(M)
High Dielectric Constant Type X5R(R6) Characteristics
LxW [mm]
Rated Volt. [Vdc]
Capacitance Tolerance Part Number
16(1C) 10(1A)
GNM1M2R61C105MEA2D* GNM1M2R61A105MEA4D*
1.37x1.0(1M)<0504>
Number of Elements 2(2)10(1A)
GNM214R61A105MEA2D*
2.0x1.25(21)<0805>
4(4)
1.0µF(105)±20%(M)
The part number code is shown in ( ) and Unit is shown in [ ]. < >: EIA [inch] Code
* Please refer to GNM series Specifications and Test Method (2).
High Dielectric Constant Type X5R(R6) Characteristics-Low Profile
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Continued on the following page.
GNM Series Specifications and Test Methods (1)
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig.1 using a eutectic solder. Then apply 5N force in parallel with
the test jig for 10±1 sec.
The soldering should be done either with an iron or using the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
(in mm)
Fig. 1
10 Adhesive Strength
of Termination
No removal of the terminations or other defect should occur.
GNMpp4 GNMpp2
The capacitance change should be measured after 5 min. at
each specified temperature stage.
(1) Temperature Compensating Type
The temperature coefficient is determined using the capaci-
tance measured in step 3 as a reference. When cycling the
temperature sequentially from steps 1 through 5, the
capacitance should be within the specified tolerance for the
temperature coefficient and capacitance change as in Table A.
The capacitance drift is calculated by dividing the differences
between the maximum and minimum measured values in the
steps 1, 3 and 5 by the cap. value in step 3.
(2) High Dielectric Constant Type
The ranges of capacitance change compared with the above
25°C value over the temperature ranges shown in the table
should be within the specified ranges.
9
Capacitance
Temperature
Characteristics
Capacitance
Change
Within the
specified tolerance
(Table A)
Temperature
Coefficient
Within the
specified tolerance
(Table A)
Capacitance
Drift
Within ±0.2%
or ±0.05pF
(whichever is
larger.)
8Q/
Dissipation Factor
(D.F.)
30pF min.: QU1000
30pF max.:
QU400+20C
C: Nominal
Capacitance (pF)
The capacitance/Q/D.F. should be measured at 25°C at the
frequency and voltage shown in the table.
7 Capacitance Within the specified tolerance
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at 25°C and 75%RH
max. and within 2 minutes of charging.
6Insulation
Resistance More than 10,000MΩ or 500Ω · F
(whichever is smaller)
No failure should be observed when 300% of the rated voltage
(5C) or 250% of the rated voltage (R7) is applied between the
terminations for 1 to 5 seconds, provided the charge/discharge
current is less than 50mA.
5 Dielectric Strength No defects or abnormalities
Using calipers4 Dimensions Within the specified dimensions
Visual inspection3 Appearance No defects or abnormalities
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, VP-P or VO-P,
whichever is larger, should be maintained within the rated
voltage range.
2 Rated Voltage See the previous pages.
1Operating
Temperature
Range 5C: –55 to +125°CR7, C7: –55 to +125°C
R6: –55 to +85°C
No. Test Method
Specifications
Temperature
Compensating Type
High Dielectric Type
Item
Step Temperature (°C)
25±2
–55±3 (for 5C/R7/C7), –30±3 (for F5)
25±2
125±3 (for 5C/R7/C7), 85±3 (for F5)
25±2
1
2
3
4
5
Char.
Item 5C
1±0.1MHz
0.5 to 5Vrms
R7
1±0.1kHz
1.0±0.2Vrms
Frequency
Voltage
Char.
25V min.
0.025
max.
16V
0.035
max.
10V
0.035
max.
6.3V
0.05
max.
R7, R6,
C7
Char. Temp.
Range
–55°C
to +125°C
Reference
Temp.
25°C
Cap.
Change
Within
±15%
R7
–55°C
to +85°CWithin
±22%
R6
–55°C
to +125°C
C7
Type a
0.5
0.6
0.6
0.8
b
1.6
1.8
2.0
2.5
c
0.32
0.5
0.25
0.4
d
0.32
0.5
0.25
0.4
GNM1M2
GNM212
GNM214
GNM314
Solder resist
Copper foil
c
d
b b
aa
c
d
Solder resist
Copper foil
• Initial measurement for high dielectric constant type.
Perform a heat treatment at 150+0/-10°C for one hour and
then set for 24±2 hours at room temperature.
Perform the initial measurement.
!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
0. Please check with our sales representatives or product engineers before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0. specifications before ordering.
GNM Series Specifications and Test Methods (1)
70
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Continued from the preceding page.
Continued on the following page.
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270±5°C for 10±0.5 seconds. Let sit at room
temperature for 24±2 hours, then measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
14
Resistance to
Soldering Heat The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No marking defects
Capacitance
Change
Within ±2.5%
or ±0.25pF
(whichever is
larger)
R7, R6, C7: Within ±7.5%
Q/D.F.
30pF min.: QU1000
30pF max.:
QU400+20C
C: Nominal
Capacitance (pF)
I.R. More than 10,000MΩ or 500Ω · F (whichever is smaller)
Dielectric
Strength
No failure
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2±0.5 seconds at 230±5°C or
Sn-3.0Ag-0.5Cu solder solution for 2±0.5 seconds at 245±5°C.
13 Solderability of
Termination 75% of the terminations are to be soldered evenly and
continuously.
GNM Series Specifications and Test Methods (1)
Char.
25V min.
0.025
max.
16V
0.035
max.
10V
0.035
max.
6.3V
0.05
max.
R7, R6,
C7
Char.
25V min.
0.025
max.
16V
0.035
max.
10V
0.035
max.
6.3V
0.05
max.
R7, R6,
C7
Type a
2.0±0.05
2.0±0.05
2.0±0.05
2.5±0.05
b
0.5±0.05
0.6±0.05
0.7±0.05
0.8±0.05
c
0.32±0.05
0.5±0.05
0.3±0.05
0.4±0.05
d
0.32±0.05
0.5±0.05
0.2±0.05
0.4±0.05
GNM1M2
GNM212
GNM214
GNM314
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2 using a eutectic solder.
Then apply a force in the direction shown in Fig. 3 for 5±1 sec.
The soldering should be done by the reflow method and should
be conducted with care so that the soldering is uniform and free
of defects such as heat shock.
Fig. 3
12 Deflection
Appearance
No marking defects
Capacitance
Change
Within ±5% or ±0.5pF
(whichever is larger) Within ±10%
(in mm)
Fig. 2
•GNMpp4 •GNMpp2
Solder the capacitor to the test jig (glass epoxy board) in the
same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually perpendic-
ular directions (total of 6 hours).
11
Vibration
Resistance
Appearance
No defects or abnormalities
Capacitance
Within the specified tolerance
Q/D.F.
30pF min.: QU1000
30pF max.:
QU400+20C
C: Nominal
Capacitance (pF)
No. Test Method
Specifications
Temperature
Compensating Type
High Dielectric Type
Item
100
1.0
5.0
b
a
\`±
40
c
d
100
1.0
t=0.8mm
5.0
b
a
\_`°±
40
c
d
Capacitance meter
Flexure : V1
20 50
R230
Pressurizing
speed: 1.0mm/sec.
Pressurize
45 45
!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
0. Please check with our sales representatives or product engineers before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0. specifications before ordering.
GNM Series Specifications and Test Methods (1)
71
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Continued from the preceding page.
Continued on the following page.
Apply the rated voltage at 40±2°C and 90 to 95% humidity for
500±12 hours.
Remove and let sit for 24±2 hours at room temperature, then
measure.
The charge/discharge current is less than 50mA.
17
Humidity Load The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No marking defects
Capacitance
Change
Within ±7.5%
or ±0.75pF
(whichever is
larger)
R7, R6, C7: Within ±12.5%
Q/D.F.
30pF and over:
QU200
30pF and below:
QU100+10C/3
C: Nominal
Capacitance (pF)
I.R. More than 500MΩ or 25Ω · F (whichever is smaller)
Set the capacitor at 40±2°C and 90 to 95% humidity for 500±12
hours.
Remove and let sit for 24±2 hours at room temperature, then
measure.
16
Humidity Steady
State The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No marking defects
Capacitance
Change
Within ±5%
or ±0.5pF
(whichever is
larger)
R7, R6, C7: Within ±12.5%
Q/D.F.
30pF and over:
QU350
10pF and over,
30pF and below:
QU275+5C/2
10pF and below:
QU200+10C
C: Nominal
Capacitance (pF)
I.R. More than 1,000MΩ or 50Ω · F (whichever is smaller)
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10). Perform the five cycles
according to the four heat treatments listed in the following
table. Let sit for 24±2 hours (temperature compensating type)
or 48±4 hours (high dielectric constant type) at room
temperature, then measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
15
Temperature
Cycle The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No marking defects
Capacitance
Change
Within ±2.5%
or ±0.25pF
(whichever is
larger)
R7, R6, C7: Within ±7.5%
Q/D.F.
30pF min.: QU1000
30pF max.:
QU400+20C
C:Nominal
Capacitance (pF)
I.R. More than 10,000MΩ or 500Ω · F (whichever is smaller)
Dielectric
Strength
No failure
GNM Series Specifications and Test Methods (1)
Step
Temp. (°C)
Time (min.)
1
Min.
Operating
Temp.+0/–3
30±3
2
Room
Temp.
2 to 3
3
Max.
Operating
Temp. +3/–0
30±3
4
Room
Temp.
2 to 3
Char.
25V min.
0.025
max.
16V
0.035
max.
10V
0.035
max.
6.3V
0.05
max.
R7, R6,
C7
Char. 25V min.
0.05
max.
16V
0.05
max.
10V/6.3V
0.05
max.
R7, R6,
C7
Char. 25V min.
0.05
max.
16V
0.05
max.
10V/6.3V
0.05
max.
R7, R6,
C7
No. Test Method
Specifications
Temperature
Compensating Type
High Dielectric Type
Item
!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
0. Please check with our sales representatives or product engineers before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0. specifications before ordering.
GNM Series Specifications and Test Methods (1)
72
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Continued from the preceding page.
Apply 200% of the rated voltage for 1000±12 hours at the
maximum operating temperature ±3°C. Let sit for 24±2 hours
at room temperature, then measure.
The charge/discharge current is less than 50mA.
• Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage for one hour at the
maximum operating temperature ±3°C. Remove and let sit for
24±2 hours at room temperature. Perform initial
measurement.
18
High Temperature
Load The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No marking defects
Capacitance
Change
Within ±3%
or ±0.3pF
(whichever is
larger)
R7, R6, C7: Within ±12.5%
Q/D.F.
30pF and over:
QU350
10pF and over,
30pF and below:
QU275+5C/2
10pF and below:
QU200+10C
C: Nominal
Capacitance (pF)
I.R. More than 1,000MΩ or 50Ω · F (whichever is smaller)
No. Test Method
Specifications
Temperature
Compensating Type
High Dielectric Type
Item
Char. Nominal Values
(ppm/°C) *1
0±305C Max.
0.58 Min.
–0.24 Max.
0.40 Min.
–0.17 Max.
–55°CCapacitance Change from 25°C (%)
–30°C –10°C
0.25 Min.
–0.11
*1: Nominal values denote the temperature coefficient within a range of 25 to 125°C.
Table A
GNM Series Specifications and Test Methods (1)
Char. 25V min.
0.04
max.
16V
0.05
max.
10V/6.3V
0.05
max.
R7, R6,
C7
!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
0. Please check with our sales representatives or product engineers before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0. specifications before ordering.
GNM Series Specifications and Test Methods (1)
73
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Solder the capacitor to the test jig (glass epoxy board) in
the same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz.
The frequency range, from 10 to 55Hz and return to 10Hz,
should be traversed in approximately 1 minute. This motion
should be applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
11
Vibration
Appearance
No defects or abnormalities
Capacitance
Within the specified tolerance
D.F. 0.1 max.*3
*3 However 0.125 max. for Table 3 items.
Continued on the following page.
Temperature (°C)Step 25±2
–55±3
25±2
85±3
25±2
1
2
3
4
5
Temp. RangeChar.
–55 to +85°C
Reference
Temp.
25°C
Cap. Change
Within ±15%R6
aType 0.2
0.5
0.6
0.6
0.8
b
0.96
1.6
1.8
2.0
2.5
c
0.25
0.32
0.5
0.25
0.4
d
0.2
0.32
0.5
0.25
0.4
GNM0M2
GNM1M2
GNM212
GNM214
GNM314
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 1 using a eutectic solder.
Then apply 5N (GNM0M2: 2N) force in parallel with the test jig for
10±1 sec. The soldering should be done either with an iron or
using the reflow method and should be conducted with care so that
the soldering is uniform and free of defects such as heat shock.
(in mm)
10 Adhesive Strength
of Termination
No removal of the terminations or other defects should occur.
The capacitance change should be measured after 5 min.at
each specified temperature stage.
The ranges of capacitance change compared with the 25°C
value over the temperature ranges shown in the table should be
within the specified ranges.
• Initial measurement for high dielectric constant type.
Perform a heat treatment at 150+0/-10°C for one hour and
then set for 24±2 hours at room temperature.
Perform the initial measurement.
9Capacitance
Temperature
Characteristics
8Dissipation Factor
(D.F.)
0.1 max.*3
Table 3
*3 However 0.125 max. for Table 3 items.
The capacitance/D.F. should be measured at 25°C at the
frequency and voltage shown in the table.
Table 1
Table 2
7 Capacitance Within the specified tolerance
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at 25°C and 75%RH
max. and within 1 minute of charging.
6
Insulation Resistance
50Ω · F min.
No failure should be observed when 250% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
5 Dielectric Strength No defects or abnormalities
Using calipers4 Dimensions Within the specified dimension
Visual inspection3 Appearance No defects or abnormalities
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, VP-P or VO-P,
whichever is larger, should be maintained within the rated
voltage range.
2 Rated Voltage See the previous pages.
1
Operating
Temperature Range
R6: –55°C to +85°C
Measuring Frequency
Nominal Capacitance 1±0.1kHz
1±0.1kHz
1±0.1kHz
1±0.1kHz
Measuring Voltage
1.0±0.2Vrms
0.5±0.1Vrms
0.5±0.1Vrms
1.0±0.1Vrms
CV10µF *1 (10V min.)
CV10µF *2 (6.3V max.)
*1For items in Table1
*2For items in Table2
GNM Series Specifications and Test Methods (2)
a
Solder resist
Copper foil
c
d
b b
a
c
d
Solder resist
Copper foil
No. Test MethodSpecificationsItem
Fig. 1
GNMpp4 GNMpp2
GNM0M2 R6 1A 104
GNM0M2 R6 1C 104
GNM1M2 R6 1A 105/225
GNM1M2 R6 1C 224/105
GNM0M2 R6 0J 103/223/473
GNM212 R6 0J 225
GNM214 R6 0J 105
GNM0M2 R6 103/223/473/104
GNM1M2 R6 0J 105/225
GNM1M2 R6 1A 105MEA4
GNM1M2 R6 1A 225
GNM212 R6 0J 225
GNM212 R6 1A 225
GNM214 R6 0J 225
!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
0. Please check with our sales representatives or product engineers before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0. specifications before ordering.
GNM Series Specifications and Test Methods (2)
74
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
Continued from the preceding page.
GNM Series Specifications and Test Methods (2)
100
1.0
5.0
b
a
40
c
d
100
1.0
5.0
b
a
40
c
d
Capacitance meter
Flexure : V1
20 50
R230
Pressurizing
speed: 1.0mm/sec.
Pressurize
45 45
Apply 150% (GNM1M2R61A225/1C105: 125% of the rated
voltage) of the rated voltage for 1000±12 hours at the
maximum operating temperature ±3°C. Let sit for 24±2 hours
at room temperature, then measure.
The charge/discharge current is less than 50mA.
• Initial measurement
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
• Measurement after test
Perform a heat treatment at 150 +0/-10°C for one hour and
then let sit for 24±2 hours at room temperature, then measure.
17
Durability
Appearance
No marking defects
Capacitance
Change
R6: Within ±12.5%
D.F. 0.2 max.
I.R. 25Ω · F min.
Apply the rated voltage at 40±2°C and 90 to 95% humidity for
500±12 hours. The charge/discharge current is less than 50mA.
• Initial measurement
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
• Measurement after test
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24±2 hours at room temperature, then
measure.
16
High
Temperature
High
Humidity
(Steady)
Appearance
No marking defects
Capacitance
Change
R6: Within ±12.5%
D.F. 0.2 max.
I.R. 12.5Ω · F min.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table.
Let sit for 24±2 hours at room temperature, then measure.
• Initial measurement
Perform a heat treatment at 150 +0/-10 °C for one hour and
then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
15
Temperature
Cycle
Appearance
No marking defects
Capacitance
Change
R6*5: Within ±12.5%
*5 GNM0M2R60G105, GNM0M2R60J103/223/473/104,
GNM0M2R61A103/223/473/104,
GNM0M2R61C103/223/473/104, GNM1M2R61A105:
Within ±15%
D.F. 0.1 max. *3
*3 However 0.125 max. for Table 3 items.
I.R. 50Ω · F min.
Dielectric
Strength
No failure
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270±5°C for 10±0.5 seconds.
Let sit at room temperature for 24±2 hours, then measure.
• Initial measurement
Perform a heat treatment at 150 +0/-10°C for one hour and
then let sit for 24±2 hours at room temperature. Perform
the initial measurement.
14
Resistance
to Soldering
Heat
Appearance
No marking defects
Capacitance
Change
R6*4: Within ±7.5%
*4 GNM0M2R60G105: Within +15/-7.5%
D.F. 0.1 max. *3
*3 However 0.125 max. for Table 3 items.
I.R. 50Ω · F min.
Dielectric
Strength
No failure
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2±0.5 seconds at 230±5°C or
Sn-3.0Ag-0.5Cu solder solution for 2±0.5 seconds at 245±5°C.
13 Solderability of
Termination 75% of the terminations are to be soldered evenly
and continuously.
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 2 using a eutectic solder. Then apply a force in the
direction shown in Fig. 3. The soldering should be done by the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
12 Deflection
Appearance
No marking defects
Capacitance
Change
Within ±10%
No. Test MethodSpecificationsItem
Fig. 3
Fig. 2
Thickness: 0.8mm
#GNMpp4#GNMpp2
1Step
Min. Operating
Temp.
30±3
2
Room
Temp.
2 to 3
3
Min. Operating
Temp.
30±3
4
Room
Temp.
2 to 3
Temp. (°C)
Time (min.)
aType 2.0±0.05
2.0±0.05
2.0±0.05
2.0±0.05
2.5±0.05
b
0.2±0.05
0.5±0.05
0.6±0.05
0.7±0.05
0.8±0.05
c
0.2±0.05
0.32±0.05
0.5±0.05
0.3±0.05
0.4±0.05
d
0.25±0.05
0.32±0.05
0.5±0.05
0.2±0.05
0.4±0.05
GNM0M2
GNM1M2
GNM212
GNM214
GNM314 (in mm)
!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
0. Please check with our sales representatives or product engineers before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0. specifications before ordering.
GNM Series Specifications and Test Methods (2)
75
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
For General
GRM Series
Array
GNM Series
Low ESL
LLp Series
High-Q
GJM Series
High Frequency
GQM Series
Monolithic Microchip
GMA Series
For Bonding
GMD Series
Product Information
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
10.12.20
