Data Sheet 18-Bit, 2.5 LSB INL, 800 kSPS, SAR ADC AD7674 FEATURES FUNCTIONAL BLOCK DIAGRAM 18-bit resolution with no missing codes No pipeline delay (SAR architecture) Differential input range: VREF (VREF up to 5 V) Throughput 800 kSPS (warp mode) 666 kSPS (normal mode) 570 kSPS (impulse mode) INL: 2.5 LSB max (9.5 ppm of full scale) Dynamic range : 103 dB typ (VREF = 5 V) SINAD: 100 dB typ at 2 kHz (VREF = 5 V) Parallel (18-, 16-, or 8-bit bus) and serial 5 V/3 V interface SPI/QSPITM/MICROWIRE/DSP compatible On-board reference buffer Single 5 V supply operation Power dissipation 98 mW typ at 800 kSPS 78 mW typ at 500 kSPS (impulse mode) 160 W at 1 kSPS (impulse mode) 48-lead LQFP or 48-lead LFCSP Pin-to-pin compatible upgrade of AD7676, AD7678, and AD7679 APPLICATIONS CT scanners High dynamic data acquisition Geophone and hydrophone sensors - replacement (low power, multichannel) Instrumentation Spectrum analysis Medical instruments PDBUF REF REFGND AGND AVDD DVDD DGND OVDD AD7674 SERIAL PORT REFBUFIN IN+ 18 SWITCHED CAP DAC IN- OGND D[17:0] BUSY PARALLEL INTERFACE CLOCK PD RESET CONTROL LOGIC AND CALIBRATION CIRCUITRY WARP IMPULSE CNVST RD CS MODE0 MODE1 03083-0-001 Figure 1. Table 1. PulSARTM Selection Type PseudoDifferential True Bipolar True Differential 18-Bit Multichannel/ Simultaneous 100 kSPS to 250 kSPS AD7651, AD7660/ AD7661 AD7663 AD7675 AD7678 500 kSPS to 570 kSPS AD7650/AD7652, AD7664/AD7666 800 kSPS to 1000 kSPS AD7653, AD7667 AD7665 AD7676 AD7679 AD7654, AD7655 AD7671 AD7677 AD7674 PRODUCT HIGHLIGHTS GENERAL DESCRIPTION The AD7674 is an 18-bit, 800 kSPS, charge redistribution, successive approximation register (SAR) fully differential analog-to-digital converter (ADC) that operates on a single 5 V power supply. The device contains a high speed, 18-bit sampling ADC, an internal conversion clock, an internal reference buffer, error correction circuits, and both serial and parallel system interface ports. 1. High Resolution, Fast Throughput. The AD7674 is an 800 kSPS, charge redistribution, 18-bit, SAR ADC (no latency). 2. Excellent Accuracy. The AD7674 has a maximum integral nonlinearity of 2.5 LSB with no missing 18-bit codes. 3. Serial or Parallel Interface. Versatile parallel (18-, 16- or 8-bit bus) or 3-wire serial interface arrangement compatible with both 3 V and 5 V logic. The device is available in a 48-lead LQFP or a 48-lead LFCSP with operation specified from -40C to +85C. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2003-2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD7674 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Converter Operation.................................................................. 16 Applications ....................................................................................... 1 Typical Connection Diagram ................................................... 17 General Description ......................................................................... 1 Power Dissipation versus Throughput .................................... 20 Functional Block Diagram .............................................................. 1 Conversion Control ................................................................... 20 Product Highlights ........................................................................... 1 Digital Interface .......................................................................... 20 Table of Contents .............................................................................. 2 Parallel Interface ......................................................................... 21 Revision History ............................................................................... 2 Serial Interface ............................................................................ 21 Specifications..................................................................................... 3 Master Serial Interface ............................................................... 21 Timing Specifications .................................................................. 5 Slave Serial Interface .................................................................. 23 Absolute Maximum Ratings............................................................ 7 Microprocessor Interfacing ....................................................... 24 ESD Caution .................................................................................. 7 Applications Information .............................................................. 25 Pin Configuration and Function Descriptions ............................. 8 Layout .......................................................................................... 25 Terminology .................................................................................... 11 Evaluating AD7674 Performance............................................. 25 Typical Performance Characteristics ........................................... 12 Outline Dimensions ....................................................................... 26 Circuit Information ........................................................................ 16 Ordering Guide .......................................................................... 26 REVISION HISTORY 6/2016--Rev. A to Rev. B Changed CP-48-1 to CP-48-4 and ADSP-219x to ADSP-2191M ................................................................. Throughout Changes to Figure 4 and Table 6 ..................................................... 8 Added Figure 5; Renumbered Sequentially .................................. 8 Changes to Serial Peripheral Interface (SPI) Section................. 24 Updated Outline Dimensions ....................................................... 26 Changes to Ordering Guide .......................................................... 26 6/2009--Rev. 0 to Rev. A Changes to Zero Error, TMIN to TMAX Parameter ........................... 3 Changes to Gain Error, TMIN to TMAX Parameter........................... 3 Changes to Endnote 3 ...................................................................... 4 Changes to Pin Configuration Section .......................................... 8 Changes to Evaluating the AD7674's Performance Section...... 25 Changes to Ordering Guide .......................................................... 26 7/2003--Revision 0: Initial Version Rev. B | Page 2 of 28 Data Sheet AD7674 SPECIFICATIONS -40C to +85C, VREF = 4.096 V, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted. Table 2. Parameter RESOLUTION ANALOG INPUT Voltage Range Operating Input Voltage Analog Input CMRR Input Current Input Impedance 1 THROUGHPUT SPEED Complete Cycle Throughput Rate Time Between Conversions Complete Cycle Throughput Rate Complete Cycle Throughput Rate DC ACCURACY Integral Linearity Error Differential Linearity Error No Missing Codes Transition Noise Zero Error, TMIN to TMAX Zero Error, TMIN to TMAX Zero Error Temperature Drift Gain Error, TMIN to TMAX 3 Gain Error, TMIN to TMAX3 Gain Error Temperature Drift Power Supply Sensitivity AC ACCURACY Signal-to-Noise Dynamic Range Spurious-Free Dynamic Range Total Harmonic Distortion Signal-to-Noise-and-Distortion Ratio -3 dB Input Bandwidth SAMPLING DYNAMICS Aperture Delay Aperture Jitter Transient Response Overvoltage Recovery Test Conditions/Comments Min 18 VIN+ - VIN- VIN+, VIN- to AGND fIN = 100 kHz 800 kSPS throughput -VREF -0.1 In warp mode In warp mode In warp mode In normal mode In normal mode In impulse mode In impulse mode Typ Max Unit Bits +VREF AVDD V V dB A 1.25 800 1 1.5 666 1.75 570 s kSPS ms s kSPS s kSPS +2.5 +1.75 1.6 4 LSB 2 LSB Bits LSB LSB LSB ppm/C % of FSR % of FSR ppm/C LSB 101 99 98 97 103 120 118 105 -115 -113 -98 98 40 26 dB 4 dB dB dB dB dB dB dB dB dB dB dB dB MHz 2 5 ns ps rms ns ns 65 100 1 0 0 -2.5 -1 18 VREF = 5 V In warp mode In normal mode or impulse mode All modes In warp mode In normal mode or impulse mode All modes AVDD = 5 V 5% fIN = 2 kHz, VREF = 5 V VREF = 4.096 V fIN = 10 kHz, VREF = 4.096 V fIN = 100 kHz, VREF = 4.096 V VIN+ = VIN- = VREF/2 = 2.5 V fIN = 2 kHz fIN = 10 kHz fIN = 100 kHz fIN = 2 kHz fIN = 10 kHz fIN = 100 kHz fIN = 2 kHz, VREF = 4.096 V fIN = 2 kHz, -60 dB input Full-scale step 0.7 -25 -85 +25 +85 0.5 -0.034 -0.048 97.5 +0.034 +0.048 250 250 Rev. B | Page 3 of 28 AD7674 Parameter REFERENCE External Reference Voltage Range REF Voltage with Reference Buffer Reference Buffer Input Voltage Range REFBUFIN Input Current REF Current Drain DIGITAL INPUTS Logic Levels VIL VIH IIL IIH DIGITAL OUTPUTS Data Format 5 Pipeline Delay 6 VOL VOH POWER SUPPLIES Specified Performance AVDD DVDD OVDD Operating Current 8 AVDD DVDD 9 OVDD9 POWER DISSIPATION9 TEMPERATURE RANGE 11 Specified Performance Data Sheet Test Conditions/Comments Min Typ Max Unit REF REFBUFIN = 2.5 V REFBUFIN 3 4.05 1.8 -1 4.096 4.096 2.5 AVDD + 0.1 4.15 2.6 +1 V V V A A +0.8 DVDD + 0.3 +1 +1 V V A A 0.4 V V 5.25 5.25 DVDD + 0.3 7 V V V 90 126 138 mA mA A mW W mW mW +85 C 800 kSPS throughput 330 -0.3 +2.0 -1 -1 ISINK = 1.6 mA ISOURCE = -500 A OVDD - 0.6 4.75 4.75 2.7 5 5 800 kSPS throughput 16 6.5 50 78 160 114 126 PDBUF high at 500 kSPS 10 PDBUF high at 1 kSPS10 PDBUF high at 800 kSPS8 PDBUF low at 800 kSPS8 TMIN to TMAX -40 See the Analog Inputs section. LSB means least significant bit. With the 4.096 V input range, 1 LSB is 31.25 V. See the Terminology section. The nominal gain error is not centered at zero and is -0.029% of FSR. This specification is the deviation from this nominal value. These specifications do not include the error contribution from the external reference, but do include the error contribution from the reference buffer if used. 4 All specifications in dB are referred to a full-scale input, FS. Tested with an input signal at 0.5 dB below full scale unless otherwise specified. 5 Data format parallel or serial 18-bit. 6 Conversion results are available immediately after completed conversion. 7 The max should be the minimum of 5.25 V and DVDD + 0.3 V. 8 In warp mode. 9 Tested in parallel reading mode. 10 In impulse mode. 11 Contact factory for extended temperature range. 1 2 3 Rev. B | Page 4 of 28 Data Sheet AD7674 TIMING SPECIFICATIONS -40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted. Table 3. Parameter Refer to Figure 35 and Figure 36 Convert Pulse Width Time Between Conversions (Warp Mode/Normal Mode/Impulse Mode) 1 CNVST Low to BUSY High Delay BUSY High All Modes Except Master Serial Read After Convert (Warp Mode/ Normal Mode/Impulse Mode) Aperture Delay End of Conversion to BUSY Low Delay Conversion Time (Warp Mode/Normal Mode/Impulse Mode) Acquisition Time RESET Pulse Width Refer to Figure 37, Figure 38, and Figure 39 (Parallel Interface Modes) CNVST Low to Data Valid Delay (Warp Mode/Normal Mode/Impulse Mode) Data Valid to BUSY Low Delay Bus Access Request to Data Valid Bus Relinquish Time Refer to Figure 41 and Figure 42 (Master Serial Interface Modes) 2 CS Low to SYNC Valid Delay CS Low to Internal SCLK Valid Delay CS Low to SDOUT Delay CNVST Low to SYNC Delay (Warp Mode/Normal Mode/Impulse Mode) SYNC Asserted to SCLK First Edge Delay 3 Internal SCLK Period3 Internal SCLK High3 Internal SCLK Low3 SDOUT Valid Setup Time3 SDOUT Valid Hold Time3 SCLK Last Edge to SYNC Delay3 CS High to SYNC High-Z CS High to Internal SCLK High-Z CS High to SDOUT High-Z BUSY High in Master Serial Read After Convert3 CNVST Low to SYNC Asserted Delay (Warp Mode/Normal Mode/ Impulse Mode) SYNC Deasserted to BUSY Low Delay Refer to Figure 43 and Figure 44 (Slave Serial Interface Modes) External SCLK Setup Time External SCLK Active Edge to SDOUT Delay SDIN Setup Time SDIN Hold Time External SCLK Period External SCLK High External SCLK Low Symbol Min t1 t2 t3 10 1.25/1.5/1.75 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 t17 t18 t19 t20 t21 t22 t23 t24 t25 t26 t27 t28 Max Unit 35 ns s ns 1/1.25/1.5 2 10 1/1.25/1.5 250 10 1/1.25/1.5 20 45 15 5 10 10 10 25/275/525 3 25 12 7 4 2 3 40 10 10 10 1/1.25/1.5 25 2 Rev. B | Page 5 of 28 s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 5 3 5 5 25 10 10 s ns 18 In warp mode only, the maximum time between conversions is 1 ms; otherwise, there is no required maximum time. In serial interface modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load CL of 10 pF; otherwise, the load is 60 pF maximum. 3 In serial master read during convert mode. See Table 4 for serial master read after convert mode. 1 s ns ns s ns ns Table 4 t29 t30 t31 t32 t33 t34 t35 t36 t37 Typ ns ns ns ns ns ns ns AD7674 Data Sheet Table 4. Serial Clock Timings in Master Read After Convert DIVSCLK[1] DIVSCLK[0] SYNC to SCLK First Edge Delay Minimum Internal SCLK Period Minimum Internal SCLK Period Maximum Internal SCLK High Minimum Internal SCLK Low Minimum SDOUT Valid Setup Time Minimum SDOUT Valid Hold Time Minimum SCLK Last Edge to SYNC Delay Minimum BUSY High Width Maximum (Warp Mode) BUSY High Width Maximum (Normal Mode) BUSY High Width Maximum (Impulse Mode) Symbol t18 t19 t19 t20 t21 t22 t23 t24 t28 t28 t28 0 0 3 25 40 12 7 4 2 3 1.75 2 2.25 Rev. B | Page 6 of 28 0 1 17 60 80 22 21 18 4 60 2.5 2.75 3 1 0 17 120 160 50 49 18 30 140 4 4.25 4.5 1 1 17 240 320 100 99 18 89 300 7 7.25 7.5 Unit ns ns ns ns ns ns ns ns s s s Data Sheet AD7674 ABSOLUTE MAXIMUM RATINGS Table 5. AD7674 Absolute Maximum Ratings Parameter Analog Inputs IN+ 1, IN-1, REF, REFBUFIN, REFGND to AGND Ground Voltage Differences AGND, DGND, OGND Supply Voltages AVDD, DVDD, OVDD AVDD to DVDD, AVDD to OVDD DVDD to OVDD Digital Inputs Internal Power Dissipation 2 Internal Power Dissipation 3 Junction Temperature Storage Temperature Range Lead Temperature Range (Soldering 10 sec) 1.6mA IOL Rating TO OUTPUT PIN AGND - 0.3 V to AVDD + 0.3 V 1.4V CL 60pF1 500A 0.3 V -0.3 V to +7 V 7 V -0.3 V to +7 V -0.3 V to DVDD + 0.3 V 700 mW 2.5 W 150C -65C to +150C 300C IOH NOTE 1 IN SERIAL INTERFACE MODES,THE SYNC, SCLK, AND SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD CL OF 10pF; OTHERWISE,THE LOAD IS 60pF MAXIMUM. 03083-0-002 Figure 2. Load Circuit for Digital Interface Timing, SDOUT, SYNC, SCLK Outputs, CL = 10 pF 2V 0.8V tDELAY tDELAY 2V 0.8V 2V 0.8V 03083-0-003 See the Analog Inputs section. Specification is for device in free air: 48-Lead LQFP: JA = 91C/W, JC = 30C/W. 3 Specification is for device in free air: 48-Lead LFCSP: JA = 26C/W. 1 Figure 3. Voltage Reference Levels for Timing 2 ESD CAUTION Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. B | Page 7 of 28 AD7674 Data Sheet PDBUF AVDD REFBUFIN DNC AGND IN+ NIC NIC NIC IN- REFGND REF 48 47 46 45 44 43 42 41 40 39 38 37 REF 48 47 46 45 44 43 42 41 40 39 38 37 AGND 1 36 AGND AVDD 2 35 CNVST 34 PD MODE0 3 MODE1 4 33 RESET 32 CS AD7674 TOP VIEW (Not to Scale) 31 RD 30 DGND D1/A0 8 29 BUSY D2/A1 28 D17 9 D3 10 27 D16 D4/DIVSCLK[0] 11 26 D15 D5/DIVSCLK[1] 12 25 D14 003083-0-004 D13/RDERROR D12/SYNC D11/SCLK D10/SDOUT DGND DVDD OVDD OGND D9/RDC/SDIN D8/INVSCLK D6/EXT/INT D7/INVSYNC 13 14 15 16 17 18 19 20 21 22 23 24 NOTES 1. NIC = NO INTERNAL CONNECTION. 2. DNC = DO NOT CONNECT. AGND CNVST PD RESET CS RD DGND BUSY D17 D16 D15 D14 13 14 15 16 17 18 19 20 21 22 23 24 WARP 6 IMPULSE 7 AD7674 TOP VIEW (Not to Scale) 36 35 34 33 32 31 30 29 28 27 26 25 D6/EXT/INT D7/INVSYNC D8/INVSCLK D9/RDC/SDIN OGND OVDD DVDD DGND D10/SDOUT D11/SCLK D12/SYNC D13/RDERROR D0/OB/2C 5 AGND 1 AVDD 2 MODE0 3 MODE1 4 D0/OB/2C 5 WARP 6 IMPULSE 7 D1/A0 8 D2/A1 9 D3 10 D4/DIVSCLK[0] 11 D5/DIVSCLK[1] 12 NOTES 1. NIC = NO INTERNAL CONNECTION. 2. DNC = DO NOT CONNECT. 3. THE EXPOSED PAD IS INTERNALLY CONNECTED TO AGND. THIS CONNECTION IS NOT REQUIRED TO MEET THE ELECTRICAL PERFORMANCES. HOWEVER, FOR INCREASED RELIABILITY OF THE SOLDER JOINTS, IT IS RECOMMENDED THAT THE PAD BE SOLDERED TO THE ANALOG GROUND OF THE SYSTEM. Figure 4. 48-Lead LQFP Pin Configuration Figure 5. 48-Lead LFCSP Pin Configuration Table 6. Pin Function Descriptions Pin No. 1, 44 2, 47 3 4 Mnemonic AGND AVDD MODE0 MODE1 Type1 P P DI DI 5 D0/OB/2C DI/O 6 WARP DI 7 IMPULSE DI 8 D1/A0 DI/O 9 D2/A1 DI/O 10 D3 DO Description Analog Power Ground Pin. Input Analog Power Pins. Nominally 5 V. Data Output Interface Mode Selection. Data Output Interface Mode Selection: Interface Mode No. MODE1 MODE0 Description 0 0 0 18-bit interface 1 0 1 16-bit interface 2 1 0 Byte interface 3 1 1 Serial interface In Mode 0, 18-bit interface mode, this pin is Bit 0 of the parallel port data output bus and the data coding is straight binary. In all other modes, this pin allows a choice of straight binary/binary twos complement. When OB/2C is high, the digital output is straight binary; when low, the MSB is inverted, resulting in a twos complement output from its internal shift register. Conversion Mode Selection. When this input is high and the IMPULSE pin is low, WARP selects the fastest mode, the maximum throughput is achievable, and a minimum conversion rate must be applied to guarantee full specified accuracy. When low, full accuracy is maintained independent of the minimum conversion rate. Conversion Mode Selection. When this input is high and the WARP pin is low, IMPULSE selects a reduced power mode. In this mode, the power dissipation is approximately proportional to the sampling rate. When the WARP pin and the IMPULSE pin are low, the normal mode is selected. In Mode 0, 18-bit interface mode, this pin is Bit 1 of the parallel port data output bus. In all other modes, this input pin controls the form in which data is output, as shown in Table 7. In Mode 0, 18-bit interface mode, or Mode 1, 16-bit interface mode, this pin is Bit 2 of the parallel port data output bus. In all other modes, this input pin controls the form in which data is output, as shown in Table 7. In all modes except Mode 3, this output is used as Bit 3 of the parallel port data output bus. This pin is always an output, regardless of the interface mode. Rev. B | Page 8 of 28 003083-0-104 REFGND IN- NIC NIC NIC IN+ AGND DNC REFBUFIN AVDD PDBUF PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Data Sheet AD7674 Pin No. 11, 12 Mnemonic D4/DIVSCLK[0], D5/DIVSCLK[1] Type1 DI/O Description In all modes except Mode 3, these pins are Bit 4 and Bit 5 of the parallel port data output bus. In Mode 3, serial interface mode, when EXT/INT is low and RDC/SDIN is low (serial master read after convert), these inputs, part of the serial port, are used to slow down, if desired, the internal serial clock that clocks the data output. In other serial modes, these pins are not used. 13 D6/EXT/INT DI/O In all modes except Mode 3, this output is used as Bit 6 of the parallel port data output bus. In Mode 3, serial interface mode, this input, part of the serial port, is used as a digital select input for choosing the internal data clock or an external data clock. With EXT/INT tied low, the internal clock is selected on the SCLK output. With EXT/INT set to a logic high, the output data is synchronized to an external clock signal connected to the SCLK input. 14 D7/INVSYNC DI/O In all modes except Mode 3, this output is used as Bit 7 of the parallel port data output bus. In Mode 3, serial interface mode, this input, part of the serial port, is used to select the active state of the SYNC signal. When low, SYNC is active high. When high, SYNC is active low. 15 D8/INVSCLK DI/O In all modes except Mode 3, this output is used as Bit 8 of the parallel port data output bus. In Mode 3, serial interface mode, this input, part of the serial port, is used to invert the SCLK signal. It is active in both master and slave mode. 16 D9/RDC/SDIN DI/O In all modes except Mode 3, this output is used as Bit 9 of the parallel port data output bus. In Mode 3, serial interface mode, this input, part of the serial port, is used as either an external data input or a read mode selection input depending on the state of EXT/INT. When EXT/INT is high, RDC/SDIN can be used as a data input to daisy-chain the conversion results from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is output on SDOUT with a delay of 18 SCLK periods after the initiation of the read sequence. When EXT/INT is low, RDC/SDIN is used to select the read mode. When RDC/SDIN is high, the data is output on SDOUT during conversion. When RDC/SDIN is low, the data can be output on SDOUT only when the conversion is complete. 17 18 OGND OVDD P P 19 20 21 DVDD DGND D10/SDOUT P P DO 22 D11/SCLK DI/O 23 D12/SYNC DO 24 D13/RDERROR DO Input/Output Interface Digital Power Ground. Output Interface Digital Power. Nominally at the same supply as the host interface (5 V or 3 V). Should not exceed DVDD by more than 0.3 V. Digital Power. Nominally at 5 V. Digital Power Ground. In all modes except Mode 3, this output is used as Bit 10 of the parallel port data output bus. In Mode 3, serial interface mode, this output, part of the serial port, is used as a serial data output synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7674 provides the conversion result, MSB first, from its internal shift register. The data format is determined by the logic level of OB/2C. In serial mode when EXT/INT is low, SDOUT is valid on both edges of SCLK. In serial mode when EXT/INT is high and INVSCLK is low, SDOUT is updated on the SCLK rising edge and is valid on the next falling edge; if INVSCLK is high, SDOUT is updated on the SCLK falling edge and is valid on the next rising edge. In all modes except Mode 3, this output is used as Bit 11 of the parallel port data output bus. In Mode 3, serial interface mode, this pin, part of the serial port, is used as a serial data clock input or output, dependent upon the logic state of the EXT/INT pin. The active edge where the data SDOUT is updated depends upon the logic state of the INVSCLK pin. In all modes except Mode 3, this output is used as Bit 12 of the parallel port data output bus. In Mode 3, serial interface mode, this output, part of the serial port, is used as a digital output frame synchronization for use with the internal data clock (EXT/INT = logic low). When a read sequence is initiated and INVSYNC is low, SYNC is driven high and remains high while the SDOUT output is valid. When a read sequence is initiated and INVSYNC is high, SYNC is driven low and remains low while SDOUT output is valid. In all modes except Mode 3, this output is used as Bit 13 of the parallel port data output bus. In Mode 3, serial interface mode, and when EXT/INT is high, this output, part of the serial port, is used as an incomplete read error flag. In slave mode, when a data read is started and not complete when the following conversion is complete, the current data is lost and RDERROR is pulsed high. 25 to 28 29 D14 to D17 DO BUSY DO 30 31 DGND RD P DI Bit 14 to Bit 17 of the Parallel Port Data Output Bus. These pins are always outputs regardless of the interface mode. Busy Output. Transitions high when a conversion is started. Remains high until the conversion is complete and the data is latched into the on-chip shift register. The falling edge of BUSY can be used as a data ready clock signal. Must Be Tied to Digital Ground. Read Data. When CS and RD are both low, the interface parallel or serial output bus is enabled. Rev. B | Page 9 of 28 AD7674 Data Sheet Pin No. 32 Mnemonic CS Type1 DI 33 RESET DI 34 PD DI 35 CNVST DI 36 37 AGND REF P AI 38 39 40 to 42 43 45 46 REFGND IN- NIC AI AI IN+ DNC REFBUFIN AI 48 0 PDBUF EPAD Description Chip Select. When CS and RD are both low, the interface parallel or serial output bus is enabled. CS is also used to gate the external clock. Reset Input. When set to a logic high, reset the AD7674. Current conversion, if any, is aborted. If not used, this pin can be tied to DGND. Power-Down Input. When set to a logic high, power consumption is reduced and conversions are inhibited after the current one is completed. Start Conversion. A falling edge on CNVST puts the internal sample/hold into the hold state and initiates a conversion. In impulse mode (IMPULSE high, WARP low), if CNVST is held low when the acquisition phase (t8) is complete, the internal sample/hold is put into hold and a conversion is immediately started. Must Be Tied to Analog Ground. Reference Input Voltage and Internal Reference Buffer Output. Apply an external reference on REF if the internal reference buffer is not used. Should be decoupled effectively with or without the internal buffer. Reference Input Analog Ground. Differential Negative Analog Input. No Internal Connection. Differential Positive Analog Input. Do Not Connect. Do not connect to this pin. Reference Buffer Input Voltage. The internal reference buffer has a fixed gain. It outputs 4.096 V typically when 2.5 V is applied on this pin. Allows Choice of Buffering Reference. When low, buffer is selected. When high, buffer is switched off. Exposed Pad. The exposed pad is internally connected to AGND. This connection is not required to meet the electrical performances. However, for increased reliability of the solder joints, it is recommended that the pad be soldered to the analog ground of the system. AI DI 1 AI = Analog Input; DI = Digital Input; DI/O = Bidirectional Digital; DO = Digital Output; P = Power. Table 7. Data Bus Interface Definitions1 Mode MODE1 MODE0 D0/OB/2C D1/A0 D2/A1 D[3] D[4:9] D[10:11] D[12:15] D[16:17] Description 0 1 0 0 0 1 R[0] OB/2C R[1] A0:0 R[2] R[2] R[3] R[3] R[4:9] R[4:9] R[10:11] R[10:11] R[12:15] R[12:15] R[16:17] R[16:17] 18-bit parallel 16-bit high word 1 0 1 OB/2C A0:1 R[0] R[1] 2 1 0 OB/2C A0:0 A1:0 All high-Z R[10:11] R[12:15] R[16:17] 8-bit high byte 2 1 0 OB/2C A0:0 A1:1 All high-Z R[2:3] R[4:7] R[8:9] 8-bit mid byte 2 1 0 OB/2C A0:1 A1:0 All high-Z R[0:1] 2 1 0 OB/2C A0:1 A1:1 All high-Z 3 1 1 OB/2C 1 All high-Z R[0:17] is the 18-bit ADC value stored in its output register. Rev. B | Page 10 of 28 All zeros 16-bit low word All zeros All zeros Serial interface R[0:1] 8-bit low byte 8-bit low byte Serial interface Data Sheet AD7674 TERMINOLOGY Integral Nonlinearity Error (INL) Linearity error refers to the deviation of each individual code from a line drawn from negative full scale through positive full scale. The point used as negative full scale occurs 1/2 LSB before the first code transition. Positive full scale is defined as a level 11/2 LSB beyond the last code transition. The deviation is measured from the middle of each code to the true straight line. Differential Nonlinearity Error (DNL) In an ideal ADC, code transitions are 1 LSB apart. Differential nonlinearity is the maximum deviation from this ideal value. It is often specified in terms of resolution for which no missing codes are guaranteed. Gain Error The first transition (from 000...00 to 000...01) should occur for an analog voltage 1/2 LSB above the nominal negative full scale (-4.095991 V for the 4.096 V range). The last transition (from 111...10 to 111...11) should occur for an analog voltage 11/2 LSB below the nominal full scale (4.095977 V for the 4.096 V range). The gain error is the deviation of the difference between the actual level of the last transition and the actual level of the first transition from the difference between the ideal levels. Zero Error The zero error is the difference between the ideal midscale input voltage (0 V) from the actual voltage producing the midscale output code. Spurious-Free Dynamic Range (SFDR) SFDR is the difference, in decibels (dB), between the rms amplitude of the input signal and the peak spurious signal. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal, and is expressed in decibels. Dynamic Range Dynamic range is the ratio of the rms value of the full scale to the rms noise measured with the inputs shorted together. The value for dynamic range is expressed in decibels. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, excluding harmonics and dc. The value for SNR is expressed in decibels. Signal-to-Noise-and-Distortion Ratio (SINAD) SINAD is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, including harmonics but excluding dc. The value for SINAD is expressed in decibels. Aperture Delay Aperture delay is a measure of the acquisition performance and is measured from the falling edge of the CNVST input to when the input signal is held for a conversion. Transient Response Transient response is the time required for the AD7674 to achieve its rated accuracy after a full-scale step function is applied to its input. Effective Number of Bits (ENOB) ENOB is a measurement of the resolution with a sine wave input, and is expressed in bits. It is related to SINAD by the following formula: ENOB = (SINADdB - 1.76)/6.02 Rev. B | Page 11 of 28 AD7674 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 2.5 2.0 2.0 1.5 1.0 DNL-LSB (18-Bit) INL-LSB (18-Bit) 1.5 1.0 0.5 0 0.5 0 -0.5 -0.5 -1.0 -1.5 0 65536 131072 CODE 196608 262144 -1.0 0 65536 03083-0-005 Figure 6. Integral Nonlinearity vs. Code 131072 CODE 196608 262144 03083-0-008 Figure 9. Differential Nonlinearity vs. Code 70000 90000 VREF = 5V VREF = 5V 59121 60000 80000 58556 28939 70000 50000 COUNTS COUNTS 60000 40000 30000 50000 40000 26939 30000 25964 20000 20000 7165 10000 10000 5073 0 0 0 87 47 0 0 0 2004C 2004D 2004E 2004F 20050 20051 20052 20053 20054 20055 CODE IN HEX 0 1 793 627 8 0 2004D 2004E 2004F 20050 20051 20052 20053 20054 20055 CODE IN HEX 03083-0-009 03083-0-006 Figure 7. Histogram of 131,072 Conversions of a DC Input at the Code Transition Figure 10. Histogram of 131,072 Conversions of a DC Input at the Code Center 100 120 90 80 NUMBER OF UNITS NUMBER OF UNITS 100 80 60 40 70 60 50 40 30 20 20 10 0 -2.5 0 0 0.5 1.0 1.5 POSITIVE INL (LSB) 2.0 2.5 03083-0-007 -2.0 -1.5 1.0 NEGATIVE INL (LSB) -0.5 0 03083-0-010 Figure 11. Typical Negative INL Distribution (424 Units) Figure 8. Typical Positive INL Distribution (424 Units) Rev. B | Page 12 of 28 Data Sheet AD7674 120 250 200 NUMBER OF UNITS 80 60 40 150 100 50 20 0 0 0.5 1.0 1.5 POSITIVE DNL (LSB) 0 -2.0 2.0 03083-0-011 Figure 12. Typical Positive DNL Distribution (424 Units) -1.0 -0.5 NEGATIVE DNL (LSB) 0 03083-0-014 Figure 15. Typical Negative DNL Distribution (424 Units) 16.5 102 0 fS = 800kSPS fIN = 10kHz VREF = 4.096V SNR = 98.4dB THD = 119.1dB SFDR = 120.4dB SINAD = 98.4dB -40 -60 99 16.0 96 SNR SNR AND SINAD (dB) -20 AMPLITUDE (dB of Full Scale) -1.5 -80 -100 -120 15.5 93 90 15.0 SINAD 87 ENOB (Bits) NUMBER OF UNITS 100 14.5 84 ENOB -140 81 -160 78 14.0 50 100 150 200 250 FREQUENCY (kHz) 300 350 1 400 03083-0-012 10 100 FREQUENCY (kHz) 03083-0-015 Figure 16. SNR, SINAD, and ENOB vs. Frequency Figure 13. FFT (10 kHz Tone) 140 -60 0 fS = 800kSPS fIN = 100kHz VREF = 4.096V SNR = 98.8dB THD = 104.3dB SFDR = 104.9dB SINAD = 97.8dB -40 -60 120 -70 SFDR THD, HARMONICS (dB) -20 AMPLITUDE (dB of Full Scale) 13.5 1000 75 0 -80 -100 -120 100 -80 80 -90 THIRD HARMONIC 60 -100 THD 40 -110 SECOND HARMONIC -140 20 -120 -160 -180 0 1000 -130 0 50 100 150 200 250 FREQUENCY (kHz) 300 350 1 400 03083-0-013 10 100 FREQUENCY (kHz) 03083-0-016 Figure 17. THD, SFDR, and Harmonics vs. Frequency Figure 14. FFT (100 kHz Tone) Rev. B | Page 13 of 28 SFDR (dB) -180 AD7674 Data Sheet 100000 AVDD, WARP/NORMAL VREF = 4.096V 104 10000 103 102 101 100 SNR SINAD 99 DVDD, WARP/NORMAL OPERATING CURRENTS (A) SNR REFERRED TO FULL SCALE (dB) 105 98 97 1000 100 AVDD, IMPULSE 10 DVDD, IMPULSE 1 PDBUF HIGH 0.1 OVDD, ALL MODES 0.01 96 95 -60 -50 -40 -30 -20 -10 INPUT LEVEL (dB) 0.001 0 1 Figure 18. SNR and SINAD vs. Input Level 16.5 16.0 ENOB 15.5 98 ENOB (Bits) SINAD 15.0 97 5 25 45 65 85 03083-0-020 700 600 DVDD 500 400 AVDD 300 OVDD 100 14.5 125 105 TEMPERATURE (C) 0 -55 -35 -15 5 03083-0-018 Figure 19. SNR, SINAD, and ENOB vs. Temperature 25 45 65 TEMPERATURE (C) 85 105 125 03083-0-021 Figure 22. Power-Down Operating Currents vs. Temperature -100 25 -110 THD -120 -130 ZERO ERROR,POSITIVE AND NEGATIVE FULL SCALE (LSB) 20 THD, HARMONICS (dB) SNR, SINAD (dB) 99 POWER-DOWN OPERATING CURRENTS (nA) SNR -15 1M 100k 800 VREF = 4.096V -35 100 1k 10k SAMPLING RATE (SPS) Figure 21. Operating Current vs. Sampling Rate 100 96 -55 10 03083-0-017 THIRD HARMONIC SECOND HARMONIC 15 10 NEGATIVE FULL SCALE 5 ZERO ERROR 0 -5 -10 POSITIVE FULL SCALE -15 -20 -140 -55 -35 -15 5 25 45 65 85 105 TEMPERATURE (C) -25 -55 125 -35 -15 5 25 45 65 TEMPERATURE (C) 03083-0-019 Figure 20. THD and Harmonics vs. Temperature 85 105 125 03083-0-022 Figure 23. Zero Error, Positive Full Scale, and Negative Full Scale vs. Temperature Rev. B | Page 14 of 28 Data Sheet AD7674 50 30 OVDD = 2.7V @ 85C 10 0 40 POSITIVE FULL SCALE t12 DELAY (ns) ZERO ERROR,POSITIVE AND NEGATIVE FULL SCALE (LSB) 20 ZERO ERROR 30 20 OVDD = 2.7V @ 25C OVDD = 5V @ 85C 10 OVDD = 5V @ 25C 10 20 NEGATIVE FULL SCALE -30 4.50 4.75 5.00 AVDD (V) 5.25 0 5.50 0 50 100 CL (pF) 03083-0-023 Figure 24. Zero Error, Positive Full Scale, and Negative Full Scale vs. Supply Rev. B | Page 15 of 28 150 200 03083-0-024 Figure 25. Typical Delay vs. Load Capacitance (CL) AD7674 Data Sheet CIRCUIT INFORMATION IN+ MSB 262,144C 131,072C LSB 4C 2C C SW+ SWITCHES CONTROL C BUSY REF COMP CONTROL LOGIC OUTPUT CODE REFGND 4C 262,144C 131,072C 2C C C LSB MSB SW- IN- CNVST 03083-0-025 Figure 26. ADC Simplified Schematic The AD7674 is a very fast, low power, single-supply, precise 18-bit analog-to-digital converter (ADC) using successive approximation architecture. The linearity and dynamic range of the AD7674 are similar to or better than many - ADCs. With the advantages of its successive architecture, which ease multiplexing and reduce power with throughput, it can be advantageous in applications that normally use - ADCs. The AD7674 features different modes to optimize performance according to the applications. In warp mode, the AD7674 is capable of converting 800,000 samples per second (800 kSPS). The AD7674 provides the user with an on-chip track/hold, successive approximation ADC that does not exhibit any pipeline or latency, making it ideal for multiple multiplexed channel applications. The AD7674 can be operated from a single 5 V supply and can be interfaced to either 5 V or 3 V digital logic. It is housed in a 48-lead LQFP, or a tiny 48-lead LFCSP that offers space savings and allows for flexible configurations as either a serial or parallel interface. The AD7674 is a pin-to-pin compatible upgrade of the AD7676, AD7678, and AD7679. CONVERTER OPERATION The AD7674 is a successive approximation ADC based on a charge redistribution DAC. Figure 26 shows the simplified schematic of the ADC. The capacitive DAC consists of two identical arrays of 18 binary weighted capacitors that are connected to the two comparator inputs. During the acquisition phase, terminals of the array tied to the input of the comparator are connected to AGND via SW+ and SW-. All independent switches are connected to the analog inputs. Thus, the capacitor arrays are used as sampling capacitors and acquire the analog signal on the IN+ and IN- inputs. When the acquisition phase is complete and the CNVST input goes low, a conversion phase is initiated. When the conversion phase begins, SW+ and SW- are opened first. The two capacitor arrays are then disconnected from the inputs and connected to the REFGND input. Therefore, the differential voltage between the IN+ and IN- inputs captured at the end of the acquisition phase is applied to the comparator inputs, causing the comparator to become unbalanced. By switching each element of the capacitor array between REFGND and REF, the comparator input varies by binary weighted voltage steps (VREF/2, VREF/4, ... VREF/262144). The control logic toggles these switches, starting with the MSB first, to bring the comparator back into a balanced condition. After completing this process, the control logic generates the ADC output code and brings the BUSY output low. Modes of Operation The AD7674 features three modes of operation: warp, normal, and impulse. Each mode is more suited for specific applications. Warp mode allows conversion rates up to 800 kSPS. However, in this mode and this mode only, the full specified accuracy is guaranteed only when the time between conversions does not exceed 1 ms. If the time between two consecutive conversions is longer than 1 ms (for example, after power-up), the first conversion result should be ignored. This mode makes the AD7674 ideal for applications where a fast sample rate is required. Normal mode is the fastest mode (666 kSPS) without any limitation on the time between conversions. This mode makes the AD7674 ideal for asynchronous applications such as data acquisition systems, where both high accuracy and fast sample rate are required. Impulse mode, the lowest power dissipation mode, allows power saving between conversions. The maximum throughput in this mode is 570 kSPS. When operating at 1 kSPS, for example, it typically consumes only 136 W. This feature makes the AD7674 ideal for battery-powered applications. Rev. B | Page 16 of 28 Data Sheet AD7674 Transfer Functions Table 8. Output Codes and Ideal Input Voltages ADC CODE (Straight Binary) Except in 18-bit interface mode, the AD7674 offers straight binary and twos complement output coding when using OB/2C. See Figure 27 and Table 8 for the ideal transfer characteristic. Description FSR - 1 LSB FSR - 2 LSB Midscale + 1 LSB Midscale Midscale - 1 LSB -FSR + 1 LSB -FSR 111...111 111...110 111...101 Straight Binary (Hex) 3FFFF1 3FFFE 20001 20000 1FFFF 00001 000002 Analog Input VREF = 4.096 V 4.095962 V 4.095924 V 31.25 V 0V -31.25 V -4.095962 V -4.096 V Twos Complement (Hex) 1FFFF1 1FFFE 00001 00000 3FFFF 20001 200002 1 This is also the code for overrange analog input (VIN+ - VIN- above VREF - VREFGND). 2 This is also the code for underrange analog input (VIN+ - VIN- below -VREF + VREFGND). 000...010 000...001 TYPICAL CONNECTION DIAGRAM 000...000 -FS -FS + 1 LSB +FS - 1 LSB -FS + 0.5 LSB Figure 28 shows a typical connection diagram for the AD7674. Different circuitry shown on this diagram is optional and is discussed later in this data sheet. +FS - 1.5 LSB ANALOG INPUT 03083-0-026 Figure 27. ADC Ideal Transfer Function DVDD ANALOG SUPPLY (5V) 20 DIGITAL SUPPLY (3.3V OR 5V) NOTE 5 + 10F + 100nF ADR421 AVDD AGND 10 F 100nF DGND DVDD REFBUFIN 2.5V REF 1M NOTE 1 50k 100nF OVDD + 10 F OGND SERIAL PORT SCLK 100nF 100nF SDOUT NOTE 2 CREF REF BUSY 47F NOTE 1 REFGND CNVST 50 NOTE 3 ANALOG INPUT+ - U1 + AD8021 D NOTE 6 15 CC IN+ AD7674 2.7nF MODE1 MODE0 OB/2C DVDD NOTE 4 PDBUF 50 NOTE 3 ANALOG INPUT- CLOCK CS - U2 + AD8021 C/P/DSP 50 RD 15 IN- RESET PD CC 2.7nF NOTE 4 NOTES 1. SEE VOLTAGE REFERENCE INPUT SECTION. 2. OPTIONAL CIRCUITRY FOR HARDWARE GAIN CALIBRATION. 3.THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION. 4. SEE ANALOG INPUTS SECTION. 5. OPTION, SEE POWER SUPPLY SECTION. 6. OPTIONAL LOW JITTER CNVST, SEE CONVERSION CONTROL SECTION. 03083-0-027 Figure 28. Typical Connection Diagram (Internal Reference Buffer, Serial Interface) Rev. B | Page 17 of 28 AD7674 Data Sheet Analog Inputs Figure 29 shows a simplified analog input section of the AD7674. The diodes shown in Figure 29 provide ESD protection for the inputs. Care must be taken to ensure that the analog input signal never exceeds the absolute ratings on these inputs. This causes these diodes to become forward biased and start conducting current. These diodes can handle a forward-biased current of 120 mA max. This condition can eventually occur when the U1 or U2 supplies of the input buffer are different from AVDD. In such a case, an input buffer with a short-circuit current limitation can be used to protect the device. filter between the amplifier output and the ADC analog inputs, as shown in Figure 28, to improve the noise filtering done by the AD7674 analog input circuit. However, the source impedance has to be kept low because it affects the ac performance, especially the total harmonic distortion (THD). The maximum source impedance depends on the amount of THD that can be tolerated. The THD degrades as a function of source impedance and the maximum input frequency, as shown in Figure 31. -95 20kHz -100 AVDD THD (dB) -105 R+ = 102 IN+ CS 10kHz -110 CS IN- 2kHz -115 R- = 102 -120 15 AGND 03083-0-028 Figure 29. Simplified Analog Input 66 Driver Amplifier Choice Although the AD7674 is easy to drive, the driver amplifier needs to meet the following requirements: * 64 CMRR (dB) 62 60 58 56 * 54 52 10 100 FREQUECY (kHz) 1000 105 03083-0-030 Figure 31. THD vs. Analog Input Frequency and Source Resistance This analog input structure is a true differential structure. By using these differential inputs, signals common to both inputs are rejected as shown in Figure 30, which represents typical CMRR over frequency. 50 1 45 75 INPUT RESISTANCE () 10000 03083-0-029 Figure 30. Analog Input CMRR vs. Frequency During the acquisition phase for ac signals, the AD7674 behaves like a 1-pole RC filter consisting of the equivalent resistance R+, R-, and CS. The R+ and R- resistors are typically 102 and are lumped components made up of a serial resistor and the on resistance of the switches. CS is typically 60 pF and mainly consists of the ADC sampling capacitor. This 1-pole filter with a -3 dB cutoff frequency of 26 MHz typ reduces any undesirable aliasing effect and limits the noise coming from the inputs. Because the input impedance of the AD7674 is very high, the device can be driven directly by a low impedance source without gain error. This allows the user to put an external 1-pole RC Rev. B | Page 18 of 28 The driver amplifier and the AD7674 analog input circuit have to be able to settle for a full-scale step of the capacitor array at an 18-bit level (0.0004%). In the amplifier data sheet, settling at 0.1% or 0.01% is more commonly specified. This can differ significantly from the settling time at an 18-bit level and, therefore, should be verified prior to driver selection. The tiny op amp AD8021, which combines ultralow noise and high gain-bandwidth, meets this settling time requirement. The noise generated by the driver amplifier needs to be kept as low as possible to preserve the SNR and transition noise performance of the AD7674. The noise coming from the driver is filtered by the AD7674 analog input circuit 1pole low-pass filter made by R+, R-, and CS. The SNR degradation due to the amplifier is SNRLOSS = 20 log 25 625 + f -3dB (Ne N )2 where: f-3dB is the -3 dB input bandwidth in MHz of the AD7674 (26 MHz) or the cutoff frequency of the input filter, if used. N is the noise factor of the amplifiers (1 if in buffer configuration). eN is the equivalent input noise voltage of each op amp in nV/Hz. Data Sheet * AD7674 For instance, for a driver with an equivalent input noise of 2 nV/Hz (for example, the AD8021) configured as a buffer, thus with a noise gain of +1, the SNR degrades by only 0.34 dB with the filter in Figure 28, and by 1.8 dB without it. The driver needs to have a THD performance suitable to that of the AD7674. The AD8021 meets these requirements and is usually appropriate for almost all applications. The AD8021 needs a 10 pF external compensation capacitor, which should have good linearity as an NPO ceramic or mica type. The AD8022 can be used if a dual version is needed and gain of 1 is present. The AD829 is an alternative in applications where high frequency (above 100 kHz) performance is not required. In gain of 1 applications, it requires an 82 pF compensation capacitor. The AD8610 is another option when low bias current is needed in low frequency applications. Single-to-Differential Driver For applications using unipolar analog signals, a single-endedto-differential driver allows for a differential input into the device. The schematic is shown in Figure 32. When provided an input signal of 0 to VREF, this configuration produces a differential VREF with midscale at VREF/2. If the application can tolerate more noise, the AD8138 differential driver can be used. ANALOG INPUT (UNIPOLAR 0V TO 4.096V) AD8021 10pF 1.82k 2.7nF AD8021 8.25k 100nF AD7674 15 U2 10pF Using the internal reference buffer is recommended when sharing a common reference voltage between multiple ADCs is desired. However, the advantages of using the external reference voltage directly are: * * The SNR and dynamic range improvement (about 1.7 dB) resulting from the use of a reference voltage very close to the supply (5 V) instead of a typical 4.096 V reference when the internal buffer is used. The power saving when the internal reference buffer is powered down (PDBUF High) To use the internal reference buffer, PDBUF should be LOW. A 2.5 V reference voltage applied on the REFBUFIN input results in a 4.096 V reference on the REF pin. In both cases, the voltage reference input REF has a dynamic input impedance and therefore requires an efficient decoupling between REF and REFGND inputs, The decoupling consists of a low ESR 47 F tantalum capacitor connected to the REF and REFGND inputs with minimum parasitic inductance. Power Supply 15 IN+ 590 The AD7674 allows the use of an external voltage reference either with or without the internal reference buffer. Care should also be taken with the reference temperature coefficient of the voltage reference, which directly affects the full-scale accuracy if this parameter matters. For instance, a 4 ppm/C temperature coefficient of the reference changes the full scale by 1 LSB/C. U1 590 Voltage Reference IN- REF 2.7nF REFBUFIN 10F 2.5V 03083-0-031 Figure 32. Single-Ended-to-Differential Driver Circuit (Internal Reference Buffer Used) The AD7674 uses three sets of power supply pins: an analog 5 V supply (AVDD), a digital 5 V core supply (DVDD), and a digital output interface supply (OVDD). The OVDD supply defines the output logic level and allows direct interface with any logic working between 2.7 V and DVDD + 0.3 V. To reduce the number of supplies needed, the digital core (DVDD) can be supplied through a simple RC filter from the analog supply, as shown in Figure 28. The AD7674 is independent of power supply sequencing once OVDD does not exceed DVDD by more than 0.3 V, and is therefore free from supply voltage induced latch-up. Additionally, it is very insensitive to power supply variations over a wide frequency range, as shown in Figure 33. Rev. B | Page 19 of 28 AD7674 Data Sheet 70 t2 t1 CNVST 65 PSRR (dB) 60 BUSY t4 t3 55 t6 t5 MODE 50 ACQUIRE CONVERT ACQUIRE t7 t8 CONVERT 03083-0-034 45 Figure 35. Basic Conversion Timing 40 1 10 100 FREQUECY (kHz) 1000 Although CNVST is a digital signal, it should be designed with special care with fast, clean edges and levels with minimum overshoot and undershoot or ringing. 10000 03083-0-032 Figure 33. PSRR vs. Frequency POWER DISSIPATION VERSUS THROUGHPUT In Impulse mode, the AD7674 automatically reduces its power consumption at the end of each conversion phase. During the acquisition phase, the operating currents are very low, which allows for a significant power savings when the conversion rate is reduced, as shown in Figure 34. This feature makes the AD7674 ideal for very low power battery applications. It should be noted that the digital interface remains active even during the acquisition phase. To reduce the operating digital supply currents even further, the digital inputs need to be driven close to the power rails (DVDD and DGND), and OVDD should not exceed DVDD by more than 0.3 V. 1000000 WARP/NORMAL POWER DISSAPATION (W) 100000 For applications where SNR is critical, the CNVST signal should have very low jitter. This may be achieved by using a dedicated oscillator for CNVST generation, or to clock it with a high frequency low jitter clock, as shown in Figure 28. In Impulse mode, conversions can be initiated automatically. If CNVST is held low when BUSY goes low, the AD7674 controls the acquisition phase and automatically initiates a new conversion. By keeping CNVST low, the AD7674 keeps the conversion process running by itself. Note that the analog input has to be settled when BUSY goes low. Also, at power-up, CNVST should be brought low once to initiate the conversion process. In this mode, the AD7674 can sometimes run slightly faster than the guaranteed limits of 570 kSPS in Impulse mode. This feature does not exist in Warp or Normal modes. DIGITAL INTERFACE 10000 The AD7674 has a versatile digital interface; it can be interfaced with the host system by using either a serial or parallel interface. The serial interface is multiplexed on the parallel data bus. The AD7674 digital interface also accommodates both 3 V and 5 V logic by simply connecting the OVDD supply pin of the AD7674 to the host system interface digital supply. Finally, by using the OB/2C input pin in any mode but 18-bit interface mode, both twos complement and straight binary coding can be used. 1000 100 IMPULSE 10 PDBUF HIGH 1 0.1 1 10 100 1k 10k SAMPLING RATE (SPS) 100k 1M 03083-0-033 Figure 34. Power Dissipation vs. Sample Rate CONVERSION CONTROL Figure 35 shows the detailed timing diagrams of the conversion process. The AD7674 is controlled by the CNVST signal, which initiates conversion. Once initiated, it cannot be restarted or aborted, even by PD, until the conversion is complete. The CNVST signal operates independently of CS and RD signals. The two signals, CS and RD, control the interface. When at least one of these signals is high, the interface outputs are in high impedance. Usually, CS allows the selection of each AD7674 in multicircuit applications, and is held low in a single AD7674 design. RD is generally used to enable the conversion result on the data bus. Rev. B | Page 20 of 28 Data Sheet AD7674 CS = 0 t9 RESET t1 CNVST, RD BUSY t4 BUSY t3 PREVIOUS CONVERSION DATA BUS DATA BUS t12 t13 03083-0-038 t8 Figure 39. Slave Parallel Data Timing for Reading (Read During Convert) CNVST CS 03083-0-035 Figure 36. RESET Timing RD CS = RD = 0 t1 A0, A1 CNVST t10 PINS D[15:8] t4 BUSY HIGH BYTE t12 t3 DATA BUS HI-Z t11 PREVIOUS CONVERSION DATA PINS D[7:0] HI-Z LOW BYTE LOW BYTE t12 HIGH BYTE Figure 40. 8-Bit and 16-Bit Parallel Interface 03083-0-036 PARALLEL INTERFACE The AD7674 is configured to use the parallel interface with an 18-bit, a 16-bit, or an 8-bit bus width, according to Table 7. The data can be read either after each conversion, which is during the next acquisition phase, or during the following conversion, as shown in Figure 38 and Figure 39, respectively. When the data is read during the conversion, however, it is recommended that it is read only during the first half of the conversion phase. This avoids any potential feedthrough between voltage transients on the digital interface and the most critical analog conversion circuitry. Refer to Table 7 for a detailed description of the different options available. CS RD t13 HI-Z 03083-0-039 NEW DATA Figure 37. Master Parallel Data Timing for Reading (Continuous Read) HI-Z SERIAL INTERFACE The AD7674 is configured to use the serial interface when MODE0 and MODE1 are held high. The AD7674 outputs 18 bits of data, MSB first, on the SDOUT pin. This data is synchronized with the 18 clock pulses provided on the SCLK pin. The output data is valid on both the rising and falling edge of the data clock. MASTER SERIAL INTERFACE Internal Clock The AD7674 is configured to generate and provide the serial data clock SCLK when the EXT/INT pin is held low. The AD7674 also generates a SYNC signal to indicate to the host when the serial data is valid. The serial clock SCLK and the SYNC signal can be inverted if desired. Depending on the RDC/SDIN input, the data can be read after each conversion or during the following conversion. Figure 41 and Figure 42 show the detailed timing diagrams of these two modes. Usually, because the AD7674 is used with a fast throughput, the master read during conversion mode is the most recommended serial mode. BUSY DATA BUS CURRENT CONVERSION t12 t13 03083-0-037 Figure 38. Slave Parallel Data Timing for Reading (Read After Convert) In read during conversion mode, the serial clock and data toggle at appropriate instants, minimizing potential feedthrough between digital activity and critical conversion decisions. In read after conversion mode, note that unlike in other modes, the BUSY signal returns low after the 18 data bits are pulsed out and not at the end of the conversion phase, which results in a longer BUSY width. To accommodate slow digital hosts, the serial clock can be slowed down by using DIVSCLK. Rev. B | Page 21 of 28 AD7674 Data Sheet RDC/SDIN = 0 EXT/INT = 0 CS, RD INVSCLK = INVSYNC = 0 t3 CNVST t28 BUSY t30 t29 t25 SYNC t18 t19 t14 t20 t24 t21 t26 1 2 D17 D16 SCLK 3 16 17 D2 D1 18 t15 t27 X SDOUT t16 D0 t23 t22 03083-0-040 Figure 41. Master Serial Data Timing for Reading (Read After Convert) RDC/SDIN = 1 EXT/INT = 0 CS, RD INVSCLK = INVSYNC = 0 t1 CNVST t3 BUSY t17 t25 SYNC t14 t19 t20 t21 t15 SCLK 1 t24 2 3 16 17 t18 X SDOUT t16 t27 D17 t22 t26 18 D16 D2 D1 D0 t23 03083-0-046 Figure 42. Master Serial Data Timing for Reading (Read Previous Conversion During Convert) Rev. B | Page 22 of 28 Data Sheet AD7674 External Discontinuous Clock Data Read after Conversion SLAVE SERIAL INTERFACE External Clock Though maximum throughput cannot be achieved using this mode, it is the most recommended of the serial slave modes. Figure 43 shows the detailed timing diagrams of this method. After a conversion is complete, indicated by BUSY returning low, the result of this conversion can be read while both CS and RD are low. Data is shifted out MSB first with 18 clock pulses, and is valid on the rising and falling edge of the clock. The AD7674 is configured to accept an externally supplied serial data clock on the SCLK pin when the EXT/INT pin is held high. In this mode, several methods can be used to read the data. The external serial clock is gated by CS. When CS and RD are both low, the data can be read after each conversion or during the following conversion. The external clock can be either a continuous or a discontinuous clock. A discontinuous clock can be either normally high or normally low when inactive. Figure 43 and Figure 44 show the detailed timing diagrams of these methods. While the AD7674 is performing a bit decision, it is important that voltage transients not occur on digital input/output pins or degradation of the conversion result can occur. This is particularly important during the second half of the conversion phase because the AD7674 provides error correction circuitry that can correct for an improper bit decision made during the first half of the conversion phase. For this reason, it is recommended that when an external clock is being provided, it is a discontinuous clock that only toggles when BUSY is low or, more importantly, that it does not transition during the latter half of BUSY high. Among the advantages of this method, the conversion performance is not degraded because there are no voltage transients on the digital interface during the conversion process. Also, data can be read at speeds up to 40 MHz, accommodating both slow digital host interface and the fastest serial reading. Finally, in this mode only, the AD7674 provides a daisy-chain feature using the RDC/SDIN input pin to cascade multiple converters together. This feature is useful for reducing component count and wiring connections when desired (for instance, in isolated multiconverter applications). An example of the concatenation of two devices is shown in Figure 45. Simultaneous sampling is possible by using a common CNVST signal. It should be noted that the RDC/SDIN input is latched on the edge of SCLK opposite the one used to shift out data on SDOUT. Thus, the MSB of the upstream converter follows the LSB of the downstream converter on the next SCLK cycle. INVSCLK = 0 EXT/INT = 1 RD = 0 CS BUSY t36 SCLK t35 t37 1 2 t31 3 16 17 18 19 20 t32 SDOUT X t16 D17 D16 D15 D1 D0 X17 X16 X16 X15 X1 X0 Y17 Y16 t34 SDIN X17 t33 03083-0-042 Figure 43. Slave Serial Data Timing for Reading (Read After Convert) Rev. B | Page 23 of 28 AD7674 Data Sheet EXT/INT = 1 INVSCLK = 0 RD = 0 CS CNVST BUSY t3 t35 t36 SCLK t37 1 2 t31 SDOUT 3 16 17 18 t32 X D17 D16 D1 D15 D0 t16 03083-0-043 Figure 44. Slave Serial Data Timing for Reading (Read Previous Conversion During Convert) input/output ports on a microcontroller. A variety of external buffers can be used with the AD7674 to prevent digital noise from coupling into the ADC. The Serial Peripheral Interface (SPI) section illustrates the use of the AD7674 with an SPI equipped DSP, the ADSP-2191M. BUSY OUT BUSY AD7674 #2 (UPSTREAM) #1 (DOWNSTREAM) RDC/SDIN SDOUT RDC/SDIN CNVST SDOUT DATA OUT Serial Peripheral Interface (SPI) CNVST CS CS SCLK SCLK SCLK IN CS IN CNVST IN 03083-0-044 Figure 45. Two AD7674 Devices in a Daisy-Chain Configuration External Clock Data Read during Conversion Figure 44 shows the detailed timing diagrams of this method. During a conversion, while both CS and RD are low, the result of the previous conversion can be read. The data is shifted out MSB first with 18 clock pulses, and is valid on both the rising and falling edge of the clock. The 18 bits have to be read before the current conversion is complete. If that is not done, RDERROR is pulsed high and can be used to interrupt the host interface to prevent incomplete data reading. There is no daisy-chain feature in this mode, and the RDC/SDIN input should always be tied either high or low. To reduce performance degradation due to digital activity, a fast discontinuous clock is recommended to ensure that all bits are read during the first half of the conversion phase. It is also possible to begin to read the data after conversion and continue to read the last bits even after a new conversion has been initiated. The AD7674 digital interface is compatible with SPI. As an example, Figure 46 shows an interface diagram between the AD7674 and the SPI equipped ADSP-2191M. To accommodate the slower speed of the DSP, the AD7674 acts as a slave device, and data must be read after conversion. This mode also allows the daisy-chain feature. The convert command can be initiated in response to an internal timer interrupt. The 18-bit output data are read with 3-byte SPI access. The reading process can be initiated in response to the end-of-conversion signal (BUSY going low) using an interrupt line of the DSP. The serial interface (SPI) on the ADSP-2191M is configured for master mode (MSTR) = 1, Clock Polarity Bit (CPOL) = 0, Clock Phase Bit (CPHA) = 1, and SPI interrupt enable (TIMOD) = 00, by writing to the SPI Control register (SPICLTx). It should be noted that to meet all timing requirements, the SPI clock should be limited to 17 Mbps, which allows it to read an ADC result in about 1.1 s. When a higher sampling rate is desired, use of one of the parallel interface modes is recommended. DVDD ADSP-2191M* AD7674* SER/PAR EXT/INT BUSY CS MICROPROCESSOR INTERFACING RD The AD7674 is ideally suited for traditional dc measurement applications supporting a microprocessor, and for ac signal processing applications interfacing to a digital signal processor. The AD7674 is designed to interface either with a parallel 8-bit or 16-bit wide interface, or with a general-purpose serial port or Rev. B | Page 24 of 28 INVSCLK SDOUT SCLK CNVST PFx SPIxSEL (PFx) MISOx SCKx PFx or TFSx *ADDITIONAL PINS OMITTED FOR CLARITY Figure 46. Interfacing the AD7674 to an SPI Interface 03083-0-045 BUSY AD7674 Data Sheet AD7674 APPLICATIONS INFORMATION RC filter (see Figure 28) and connect the system supply to the interface digital supply OVDD and the remaining digital circuitry. When DVDD is powered from the system supply, it is useful to insert a bead to further reduce high frequency spikes. LAYOUT The AD7674 has very good immunity to noise on the power supplies. However, care should still be taken with regard to grounding layout. The printed circuit board that houses the AD7674 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. This calls for the use of ground planes, which can be easily separated. Digital and analog ground planes should be joined in only one place, preferably underneath the AD7674, or at least as close to the AD7674 as possible. If the AD7674 is in a system where multiple devices require analog-to-digital ground connections, the connection should still be made at one point only, a star ground point that should be established as close to the AD7674 as possible. The user should avoid running digital lines under the device, as these couple noise onto the die. The analog ground plane should be allowed to run under the AD7674 to avoid noise coupling. Fast switching signals like CNVST or clocks should be shielded with digital ground to avoid radiating noise to other sections of the board, and should never run near analog signal paths. Crossover of digital and analog signals should be avoided. Traces on different but close layers of the board should run at right angles to each other. This reduces the effect of feedthrough through the board. The power supply lines to the AD7674 should use as large a trace as possible to provide low impedance paths and reduce the effect of glitches on the power supply lines. Good decoupling is also important to lower the impedance of the supply presented to the AD7674 and to reduce the magnitude of the supply spikes. Decoupling ceramic capacitors, typically 100 nF, should be placed close to and ideally right up against each power supply pin (AVDD, DVDD, and OVDD) and their corresponding ground pins. Additionally, low ESR 10 F capacitors should be located near the ADC to further reduce low frequency ripple. The DVDD supply of the AD7674 can be a separate supply or can come from the analog supply, AVDD, or the digital interface supply, OVDD. When the system digital supply is noisy or when fast switching digital signals are present, and if no separate supply is available, the user should connect the DVDD digital supply to the analog supply AVDD through an The AD7674 has four different ground pins: REFGND, AGND, DGND, and OGND. REFGND senses the reference voltage and should be a low impedance return to the reference because it carries pulsed currents. AGND is the ground to which most internal ADC analog signals are referenced. This ground must be connected with the least resistance to the analog ground plane. DGND must be tied to the analog or digital ground plane depending on the configuration. OGND is connected to the digital system ground. The layout of the decoupling of the reference voltage is important. The decoupling capacitor should be close to the ADC and should be connected with short and large traces to minimize parasitic inductances. EVALUATING AD7674 PERFORMANCE An evaluation board for the AD7674 allows a quick means to measure both DC (histograms and time domain) and AC (time and frequency domain) performances of the converter. The EVAL-AD7674CBZ is an evaluation board package that includes a fully assembled and tested evaluation board, documentation, and software. The accompanying software requires the use of a capture board which must be ordered separately from the evaluation board (see the Ordering Guide for information). The evaluation board can also be used in a standalone configuration and does not use the software when in this mode. Refer to the EVAL-AD76XXEDZ and EVALAD76XXCBZ for evaluation board details. Two types of data capture boards can be used with the EVALAD7674CBZ: * * USB based (EVAL-CED1Z recommended) Parallel port based (EVAL-CONTROL BRD3Z not recommended as many newer PCs do not include parallel ports any longer) The recommended board layout for the AD7674 is outlined in the evaluation board data sheet. Rev. B | Page 25 of 28 AD7674 Data Sheet OUTLINE DIMENSIONS 0.75 0.60 0.45 9.00 BSC SQ 1.60 MAX 37 48 36 1 1.45 1.40 1.35 0.15 0.05 PIN 1 SEATING PLANE 10 6 2 (PINS DOWN ) VIEW A 7 3.5 0 0.10 MAX COPLANARITY SEATING PLANE 7.00 BSC SQ TOP VIEW 0.20 0.09 25 12 24 13 0.27 0.22 0.17 0.50 BSC VIEW A ROTATED 90 CCW COMPLIANT TO JEDEC STANDARDS MS-026BBC Figure 47. 48-Lead Low Profile Quad Flat Package [LQFP] (ST-48) Dimensions shown in millimeters 0.30 0.23 0.18 PIN 1 INDICATOR 48 37 36 1 0.50 BSC TOP VIEW 0.80 0.75 0.70 0.45 0.40 0.35 5.20 5.10 SQ 5.00 EXPOSED PAD 12 25 24 13 BOTTOM VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE PIN 1 INDICATOR 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WKKD. 112408-B 7.00 BSC SQ Figure 48. 48-Lead Lead Frame Chip Scale Package [LFCSP] 7 mm x 7 mm Body and 0.75 mm Package Height (CP-48-4) Dimensions shown in millimeters ORDERING GUIDE Model 1, 2, 3 AD7674ASTZ AD7674ASTZL AD7674ACPZ AD7674ACPZRL EVAL-AD7674CBZ EVAL-CED1Z EVAL-CONTROL BRD2Z EVAL-CONTROL BRD3Z Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 48-Lead Low Profile Quad Flat Package [LQFP] 48-Lead Low Profile Quad Flat Package [LQFP] 48-Lead Lead Frame Chip Scale Package [LFCSP] 48-Lead Lead Frame Chip Scale Package [LFCSP] Evaluation Board USB Data Capture Board Parallel Port Capture Board, 32 k RAM Parallel Port Capture Board, 128 k RAM Package Option ST-48 ST-48 CP-48-4 CP-48-4 Z = RoHS Compliant Part. The EVAL-AD7674CBZ can be used as a standalone evaluation board or in conjunction with a capture board for evaluation/demonstration purposes. 3 The capture boards allow the PC to control and communicate with all Analog Devices evaluation boards ending in ED for EVAL-CED1Z and CB for EVAL-CONTROL BRD2Z/EVAL-CONTROL BRD3Z. 1 2 Rev. B | Page 26 of 28 Data Sheet AD7674 NOTES Rev. B | Page 27 of 28 AD7674 Data Sheet NOTES (c)2003-2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03083-0-6/16(B) Rev. B | Page 28 of 28