SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D2-kV ESD Protection for:
− LM224K, LM224KA
− LM324K, LM324KA
− LM2902K, LM2902KV, LM2902KAV
DWide Supply Ranges
− Single Supply ...3 V to 32 V
(26 V for LM2902)
− Dual Supplies . . . +1.5 V to +16 V
(+13 V for LM2902)
DLow Supply-Current Drain Independent of
Supply Voltage . . . 0.8 mA Typ
DCommon-Mode Input Voltage Range
Includes Ground, Allowing Direct Sensing
Near Ground
DLow Input Bias and Offset Parameters
− Input Offset Voltage ...3 mV Typ
A Versions ...2 mV Typ
− Input Offset Current ...2 nA Typ
− Input Bias Current...20 nA Typ
A Versions . . . 15 nA Typ
DDifferential Input Voltage Range Equal to
Maximum-Rated Supply Voltage ...32 V
(26 V for LM2902)
DOpen-Loop Differential Voltage
Amplification . . . 100 V/mV Typ
DInternal Frequency Compensation
description/ordering information
These devices consist of four independent
high-gain frequency-compensated operational
amplifiers that are designed specifically to operate
from a single supply over a wide range of voltages.
Operation from split supplies also is possible if the
difference between the two supplies is 3 V to 3 2 V
(3 V to 26 V for the LM2902), and VCC is at least
1.5 V more positive than the input common-mode
voltage. The low supply-current drain is
independent of the magnitude of the supply
voltage.
Applications include transducer amplifiers, dc amplification blocks, and all the conventional
operational-amplifier circuits that now can be more easily implemented in single-supply-voltage systems. For
example, the LM124 can be operated directly from the standard 5-V supply that is used in digital systems and
provides the required interface electronics, without requiring additional ±15-V supplies.
Copyright 2004, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!!&"&#+
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN−
1IN+
VCC
2IN+
2IN−
2OUT
4OUT
4IN−
4IN+
GND
3IN+
3IN−
3OUT
LM124 . . . D, J, OR W PACKAGE
LM124A ...J PACKAGE
LM224, LM224A, LM224K, LM224KA ...D OR N PACKAGE
LM324, LM324K . . . D, N, NS, OR PW PACKAGE
LM324A . . . D, DB, N, NS, OR PW PACKAGE
LM324KA . . . D, N, NS, OR PW PACKAGE
LM2902 . . . D, N, NS, OR PW PACKAGE
LM2902K . . . D, DB, N, NS, OR PW PACKAGE
LM2902KV, LM2902KAV ...D OR PW PACKAGE
(TOP VIEW)
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
4IN+
NC
GND
NC
3IN+
1IN+
NC
VCC
NC
2IN+
LM124, LM124A . . . FK PACKAGE
(TOP VIEW)
1IN−
1OUT
NC
3IN− 4IN−
2IN−
2OUT
NC
NC − No internal connection
3OUT 4OUT
'*%$"# $')!" " 11233 !)) '!!&"&# !& "&#"&*
%)&## ",&.#& "&*+ !)) ",& '*%$"# '*%$"
'$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+
SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
description/ordering information (continued)
ORDERING INFORMATION
TAVIOmax
AT 25°C
MAX
TESTED
VCC PACKAGE†ORDERABLE
PART NUMBER TOP-SIDE
MARKING
PDIP (N)
Tube of 25
LM324N LM324N
PDIP (N) Tube of 25 LM324KN LM324KN
Tube of 50 LM324D
LM324
SOIC (D)
Reel of 2500 LM324DR LM324
SOIC (D) Tube of 50 LM324KD
LM324K
Reel of 2500 LM324KDR LM324K
7 mV 30 V Reel of 2000 LM324NSR LM324
7 mV
30 V
SOP (NS) Tube of 50 LM324KNS
LM324K
SOP (NS)
Reel of 2000 LM324KNSR LM324K
Tube of 90 LM324PW
L324
TSSOP (PW)
Reel of 2000 LM324PWR L324
TSSOP (PW) Tube of 90 LM324KPW
L324K
Reel of 2000 LM324KPWR L324K
0°C to 70°C
PDIP (N)
Tube of 25 LM324AN LM324AN
0C to 70 C
PDIP (N) Tube of 25 LM324KAN LM324KAN
Tube of 50 LM324AD
LM324A
SOIC (D)
Reel of 2500 LM324ADR LM324A
SOIC (D) Tube of 50 LM324KAD
LM324KA
Reel of 2500 LM324KADR LM324KA
3 mV
30 V
Reel of 2000 LM324ANSR LM324A
3 mV 30 V SOP (NS) Tube of 50 LM324KANS
LM324KA
SOP (NS)
Reel of 2000 LM324KANSR LM324KA
SSOP (DB) Reel of 2000 LM324ADBR LM324A
Tube of 90 LM324APW
L324A
TSSOP (PW)
Reel of 2000 LM324APWR L324A
TSSOP (PW) Tube of 90 LM324KAPW
L324KA
Reel of 2000 LM324KAPWR L324KA
PDIP (N)
Tube of 25
LM224N LM224N
PDIP (N) Tube of 25 LM224KN LM224KN
5 mV
30 V
Tube of 50 LM224D
LM224
5 mV 30 V
SOIC (D)
Reel of 2500 LM224DR LM224
SOIC (D) Tube of 50 LM224KD
LM224K
−25°C to 85°C
Reel of 2500 LM224KDR LM224K
−25°C to 85°C
PDIP (N)
Tube of 25 LM224AN LM224AN
PDIP (N) Tube of 25 LM224KAN LM224KAN
3 mV
30 V
Tube of 50 LM224AD
LM224A
3 mV 30 V
SOIC (D)
Reel of 2500 LM224ADR LM224A
SOIC (D) Tube of 50 LM224KAD
LM224KA
Reel of 2500 LM224KADR LM224KA
†Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ORDERING INFORMATION (CONTINUED)
TAVIOmax
AT 25°C
MAX
TESTED
VCC PACKAGE†ORDERABLE
PART NUMBER TOP-SIDE
MARKING
PDIP (N)
Tube of 25 LM2902N LM2902N
PDIP (N) Tube of 25 LM2902KN LM2902KN
Tube of 50 LM2902D
LM2902
SOIC (D)
Reel of 2500 LM2902DR LM2902
SOIC (D) Tube of 50 LM2902KD
LM2902K
Reel of 2500 LM2902KDR LM2902K
Reel of 2000 LM2902NSR LM2902
26 V SOP (NS) Tube of 50 LM2902KNS
LM2902K
7 mV
26 V
SOP (NS)
Reel of 2000 LM2902KNSR LM2902K
−40°C to 125°C
7 mV
SSOP (DB)
Tube of 80 LM2902KDB
L2902K
−40 C to 125 C
SSOP (DB) Reel of 2000 LM2902KDBR L2902K
Tube of 90 LM2902PW
L2902
TSSOP (PW)
Reel of 2000 LM2902PWR L2902
TSSOP (PW) Tube of 90 LM2902KPW
L2902K
Reel of 2000 LM2902KPWR L2902K
32 V
SOIC (D) Reel of 2500 LM2902KVQDR L2902KV
32 V
TSSOP (PW) Reel of 2000 LM2902KVQPWR L2902KV
2 mV
32 V
SOIC (D) Reel of 2500 LM2902KAVQDR L2902KA
2 mV
32 V
TSSOP (PW) Reel of 2000 LM2902KAVQPWR L2902KA
CDIP (J) Tube of 25 LM124J LM124J
CFP (W) Tube of 25 LM124W LM124W
5 mV 30 V LCCC (FK) Tube of 55 LM124FK LM124FK
−55°C to 125°C
5 mV
30 V
SOIC (D)
Tube of 50 LM124D
LM124
−55 C to 125 C
SOIC (D) Reel of 2500 LM124DR LM124
2 mV
30 V
CDIP (J) Tube of 25 LM124AJ LM124AJ
2 mV
30 V
LCCC (FK) Tube of 55 LM124AFK LM124AFK
†Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
symbol (each amplifier)
−
+
IN−
IN+
OUT
SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
schematic (each amplifier)
To Other
Amplifiers
≈6-µA
Current
Regulator
VCC
OUT
GND
IN−
IN+
≈100-µA
Current
Regulator
≈50-µA
Current
Regulator
COMPONENT COUNT
(total device)
Epi-FET
Transistors
Diodes
Resistors
Capacitors
1
95
4
11
4
≈6-µA
Current
Regulator
†ESD protection cells - available on LM324K and LM324KA only
†
†
SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
LM2902 ALL OTHER
DEVICES UNIT
Supply voltage, VCC (see Note 1) ±13 or 26 ±16 or 32 V
Differential input voltage, VID (see Note 2) ±26 ±32 V
Input voltage, VI (either input) −0.3 to 26 −0.3 to 32 V
Duration of output short circuit (one amplifier) to ground at (or below) TA = 25°C,
VCC ≤ 15 V (see Note 3) Unlimited Unlimited
D package 86 86
DB package 96 96
Package thermal impedance, θ
JA
(see Notes 4 and 5) N package 80 80 °C/W
Package thermal impedance, θJA (see Notes 4 and 5)
NS package 76 76
C/W
PW package 113 113
FK package 5.61
Package thermal impedance, q
JC
(see Notes 6 and 7) J package 15.05 °C/W
Package thermal impedance, qJC (see Notes 6 and 7)
W package 14.65
C/W
Operating virtual junction temperature, TJ150 150 °C
Case temperature for 60 seconds FK package 260 °C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds J or W package 300 300 °C
Storage temperature range, Tstg −65 to 150 −65 to 150 °C
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values (except dif ferential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
2. Differential voltages are at IN+, with respect to IN−.
3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
4. Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/qJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
6. Maximum power dissipation is a function of TJ(max), qJC, and TC. The maximum allowable power dissipation at any allowable case
temperature is PD = (TJ(max) − TC)/qJC. Operating at the absolute maximum TJ of 150°C can affect reliability.
7. The package thermal impedance is calculated in accordance with MIL-STD-883.
ESD protection
TEST CONDITIONS TYP UNIT
Human-Body Model LM224K, LM224KA, LM324K, LM324KA, LM2902K, LM2902KV, LM2902KAV ±2 kV
SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
†
TA
‡LM124
LM224 LM324
LM324K
UNIT
PARAMETER
TEST CONDITIONS†
TA‡
MIN TYP§MAX MIN TYP§MAX
UNIT
VIO
Input offset voltage
VCC = 5 V to MAX,
25°C 3 5 3 7
mV
VIO Input offset voltage
VCC = 5 V to MAX,
VIC = VICRmin, VO = 1.4 V Full range 7 9 mV
IIO
Input offset current
VO = 1.4 V
25°C 2 30 2 50
nA
IIO Input offset current VO = 1.4 V Full range 100 150 nA
IIB
Input bias current
VO = 1.4 V
25°C −20 −150 −20 −250
nA
IIB Input bias current VO = 1.4 V Full range −300 −500 nA
25°C
0 to
0 to
VICR
Common-mode
VCC = 5 V to MAX
25°C
0 to
V
CC
− 1.5
0 to
V
CC
− 1.5
V
VICR
Common-mode
input voltage range VCC = 5 V to MAX
Full range
0 to
0 to
V
input voltage range
Full range
0 to
V
CC
− 2
0 to
V
CC
− 2
RL = 2 kΩ25°C VCC − 1.5 VCC − 1.5
VOH
High-level
RL = 10 kΩ25°C
V
VOH
High-level
output voltage
VCC = MAX
RL = 2 kΩFull range 26 26 V
output voltage
VCC = MAX RL ≥ 10 kΩFull range 27 28 27 28
VOL Low-level
output voltage RL ≤ 10 kΩFull range 5 20 5 20 mV
AVD
Large-signal
differential voltage
VCC = 15 V, VO = 1 V to 11 V,
25°C 50 100 25 100
V/mV
AVD differential voltage
amplification
VCC = 15 V, VO = 1 V to 11 V,
RL ≥ 2 kΩFull range 25 15 V/mV
CMRR Common-mode
rejection ratio VIC = VICRmin 25°C 70 80 65 80 dB
kSVR
Supply-voltage
rejection ratio
25°C
65
100
65
100
dB
kSVR rejection ratio
(∆V
CC
/∆V
IO
)25°C 65 100 65 100 dB
VO1/VO2 Crosstalk
attenuation f = 1 kHz to 20 kHz 25°C 120 120 dB
VCC = 15 V,
VID = 1 V,
Source
25°C −20 −30 −60 −20 −30 −60
VCC = 15 V,
VID = 1 V,
V
O
= 0 Source Full range −10 −10
mA
IOOutput current VCC = 15 V,
VID = −1 V,
Sink
25°C 10 20 10 20 mA
IO
Output current
VCC = 15 V,
VID = −1 V,
V
O
= 15 V Sink Full range 5 5
VID = −1 V, VO = 200 mV 25°C 12 30 12 30 µA
IOS Short-circuit
output current VCC at 5 V,
GND at −5 V VO = 0, 25°C±40 ±60 ±40 ±60 mA
Supply current
VO = 2.5 V, No load Full range 0.7 1.2 0.7 1.2
ICC Supply current
(four amplifiers) VCC = MAX,
VO = 0.5 VCC, No load Full range 1.4 3 1.4 3 mA
†All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for LM2902 and 30 V for the others.
‡Full range is −55°C to 125°C for LM124, −25°C to 85°C for LM224, and 0°C to 70°C for LM324.
§All typical values are at TA = 25°C.
SLOS066R − SEPTEMBER 1975 − REVISED JANUAR Y 2005
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS†
TA‡
LM2902 LM2902V
UNIT
PARAMETER
TEST CONDITIONS
†
TA
‡
MIN TYP§MAX MIN TYP§MAX UNIT
VCC = 5 V to
Non-A-suffix
25°C 3 7 3 7
VIO
Input offset voltage
VCC = 5 V to
MAX,
Non-A-suffix
devices Full range 10 10
mV
VIO Input offset voltage
MAX,
VIC = VICRmin
,
VO = 1.4 V
A-suffix
25°C 1 2 mV
VIC = VICRmin,
VO = 1.4 V
A-suffix
devices Full range 4
∆VIO/∆TInput offset voltage
temperature drift RS = 0 ΩFull range 7µV/°C
IIO
Input offset current
VO = 1.4 V
25°C 2 50 2 50
nA
IIO Input offset current VO = 1.4 V Full range 300 150 nA
∆IIO/∆TInput offset current
temperature drift Full range 10 pA/°C
IIB
Input bias current
VO = 1.4 V
25°C −20 −250 −20 −250
nA
IIB Input bias current VO = 1.4 V Full range −500 −500 nA
25°C
0 to
0 to
VICR
Common-mode
VCC = 5 V to MAX
25°C
0 to
V
CC
− 1.5
0 to
V
CC
− 1.5
V
VICR
Common-mode
input voltage range VCC = 5 V to MAX
Full range
0 to
0 to
V
input voltage range
Full range
0 to
V
CC
− 2
0 to
V
CC
− 2
RL = 2 kΩ25°C
VOH
High-level
RL = 10 kΩ25°C VCC − 1.5 VCC − 1.5
V
VOH
High-level
output voltage
VCC = MAX
RL = 2 kΩFull range 22 26 V
output voltage
VCC = MAX RL ≥ 10 kΩFull range 23 24 27
VOL Low-level
output voltage RL ≤ 10 kΩFull range 5 20 5 20 mV
AVD
Large-signal
differential voltage
VCC = 15 V, VO = 1 V to 11 V,
25°C 25 100 25 100
V/mV
AVD differential voltage
amplification
VCC = 15 V, VO = 1 V to 11 V,
RL ≥ 2 kΩFull range 15 15 V/mV
CMRR Common-mode
rejection ratio VIC = VICRmin 25°C 50 80 60 80 dB
kSVR
Supply-voltage
rejection ratio
25°C
50
100
60
100
dB
kSVR rejection ratio
(∆V
CC
/∆V
IO
)25°C 50 100 60 100 dB
VO1/VO2 Crosstalk
attenuation f = 1 kHz to 20 kHz 25°C 120 120 dB
VCC = 15 V,
VID = 1 V,
Source
25°C −20 −30 −60 −20 −30 −60
VCC = 15 V,
VID = 1 V,
VO = 0 Source Full range −10 −10
mA
IOOutput current VCC = 15 V,
VID = −1 V,
Sink
25°C 10 20 10 20 mA
O
VCC = 15 V,
VID = −1 V,
V
O
= 15 V Sink Full range 5 5
VID = −1 V, VO = 200 mV 25°C 30 12 40 µA
IOS Short-circuit
output current VCC at 5 V,
GND at −5 V VO = 0, 25°C±40 ±60 ±40 ±60 mA
Supply current
VO = 2.5 V, No load Full range 0.7 1.2 0.7 1.2
ICC Supply current
(four amplifiers) VCC = MAX,
VO = 0.5 VCC, No load Full range 1.4 3 1.4 3 mA
†All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for LM2902 and 32 V for LM2902V.
‡Full range is −40°C to 125°C for LM2902.
§All typical values are at TA = 25°C.
4444444
444444
44
SLOS066R − SEPTEMBER 1975 − REVISED JANUARY 2005
8POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
†
TA
‡LM124A LM224A LM324A,
LM324KA
UNIT
PARAMETER
TEST CONDITIONS†
TA‡
MIN TYP§MAX MIN TYP§MAX MIN TYP §MAX
UNIT
VIO
Input offset voltage
VCC = 5 V to 30 V,
25°C 2 2 3 2 3
mV
VIO Input offset voltage
VCC = 5 V to 30 V,
VIC = VICRmin, VO = 1.4 V Full range 445mV
IIO
Input offset current
VO = 1.4 V
25°C 10 2 15 2 30
nA
IIO Input offset current VO = 1.4 V Full range 30 30 75 nA
IIB
Input bias current
VO = 1.4 V
25°C −50 −15 −80 −15 −100
nA
IIB Input bias current VO = 1.4 V Full range −100 −100 −200 nA
VICR
Common-mode input
VCC = 30 V
25°C0 to
VCC − 1.5 0 to
VCC − 1.5 0 to
VCC − 1.5
V
VICR
Common-mode input
voltage range VCC = 30 V Full range 0 to
VCC − 2 0 to
VCC − 2 0 to
VCC − 2
V
RL = 2 kΩ25°C VCC − 1.5 VCC − 1.5 VCC − 1.5
V
OH
High-level output voltage
VCC = 30 V
RL = 2 kΩFull range 26 26 26 V
VOH
High-level output voltage
VCC = 30 V RL ≥ 10 kΩFull range 27 27 28 27 28
V
VOL Low-level output voltage RL ≤ 10 kΩFull range 20 5 20 5 20 mV
AVD
Large-signal differential
VCC = 15 V, VO = 1 V to 11 V,
25°C 50 100 50 100 25 100
V/mV
AVD
Large-signal differential
voltage amplification
VCC = 15 V, VO = 1 V to 11 V,
RL ≥2 kΩFull range 25 25 15 V/mV
CMRR Common-mode rejection ratio VIC = VICRmin 25°C 70 70 80 65 80 dB
kSVR Supply-voltage rejection ratio
(∆VCC/∆VIO)25°C 65 65 100 65 100 dB
VO1/VO2 Crosstalk attenuation f = 1 kHz to 20 kHz 25°C 120 120 120 dB
VCC = 15 V,
VID = 1 V,
Source
25°C −20 −20 −30 −60 −20 −30 −60
CC
VID = 1 V,
V
O
= 0
Source
Full range −10 −10 −10
mA
IOOutput current VCC = 15 V,
VID = −1 V,
Sink
25°C 10 10 20 10 20 mA
O
CC
VID = −1 V,
V
O
= 15 V Sink Full range 5 5 5
VID = −1 V, VO = 200 mV 25°C 12 12 30 12 30 µA
IOS Short-circuit output current VCC at 5 V, GND at −5 V,
VO = 0 25°C±40 ±60 ±40 ±60 ±40 ±60 mA
Supply current
VO = 2.5 V, No load Full range 0.7 1.2 0.7 1.2 0.7 1.2
ICC Supply current
(four amplifiers) VCC = 30 V, VO = 15 V,
No load Full range 1.4 3 1.4 3 1.4 3 mA
†All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified.
‡Full range is −55°C to 125°C for LM124A, −25°C to 85°C for LM224A, and 0°C to 70°C for LM324A.
§All typical values are at TA = 25°C.
SLOS066R − SEPTEMBER 1975 − REVISED JANUARY 2005
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating conditions, VCC = ±15 V, TA = 25°C
PARAMETER TEST CONDITIONS TYP UNIT
SR Slew rate at unity gain RL = 1 MΩ, CL = 30 pF, VI = ±10 V (see Figure 1) 0.5 V/µs
B1Unity-gain bandwidth RL = 1 MΩ, CL = 20 pF (see Figure 1) 1.2 MHz
VnEquivalent input noise voltage RS = 100 Ω, VI = 0 V, f = 1 kHz (see Figure 2) 35 nV/√Hz
VO
−
+
RL
CL
VI
VCC+
VCC−
Figure 1. Unity-Gain Amplifier
VO
−
+
100 ΩVCC+
VCC−
RS
900
Ω
VI = 0 V
Figure 2. Noise-Test Circuit
MECHANICAL DATA
MCFP002A – JANUARY 1995 – REVISED FEBRUAR Y 2002
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
W (R-GDFP-F14) CERAMIC DUAL FLATPACK
0.360 (9,14)
0.250 (6,35)
87
141
0.235 (5,97)
0.004 (0,10)
0.026 (0,66)
4 Places
0.015 (0,38)
0.045 (1,14)
0.335 (8,51)
0.008 (0,20)
0.045 (1,14)
Base and Seating Plane
0.005 (0,13) MIN
0.019 (0,48)
0.390 (9,91)
0.260 (6,60)
0.080 (2,03)
4040180-2/C 02/02
0.360 (9,14)
0.250 (6,35)
0.280 (7,11) MAX
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only.
E. Falls within MIL STD 1835 GDFP1-F14 and JEDEC MO-092AB
MECHANICAL DATA
MLCC006B – OCTOBER 1996
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER
4040140/D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MINMAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
12
1314151618 17
11
10
8
9
7
5
432
0.020 (0,51)
0.010 (0,25)
6
12826 27
19
21
B SQ
A SQ 22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°–ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
2016
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
80,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM PINS **
0,05
4,90
5,10
Seating Plane
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’ s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of T I products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
