Data Sheet 26182.126A 6812 DABiC-IV, 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6812xA 28 LOGIC SUPPLY 2 27 SERIAL DATA IN OUT 20 3 26 OUT 1 OUT 19 4 25 OUT 2 OUT 18 5 24 OUT 3 OUT 17 6 23 OUT 4 OUT 16 7 22 OUT 5 OUT 15 8 21 OUT 6 OUT 14 9 20 OUT 7 OUT 13 10 19 OUT 8 OUT 12 11 18 OUT 9 OUT 11 12 17 OUT 10 BLANKING 13 ST 28 16 STROBE GROUND 14 CLK 27 15 CLOCK BLNK LATCHES VDD REGISTER SERIAL DATA OUT VBB LATCHES 1 REGISTER LOAD SUPPLY Dwg. PP-029-7 ABSOLUTE MAXIMUM RATINGS at TA = 25C Logic Supply Voltage, VDD ................... 7.0 V Driver Supply Voltage, VBB ................... 60 V Continuous Output Current Range, IOUT ......................... -40 mA to +15 mA Input Voltage Range, VIN ....................... -0.3 V to VDD + 0.3 V Package Power Dissipation, PD ........................................ See Graph Operating Temperature Range, TA (Suffix `E-') .................. -40C to +85C (Suffix `S-') .................. -20C to +85C Storage Temperature Range, TS ............................... -55C to +125C Caution: These CMOS devices have input static protection (Class 2) but are still susceptible to damage if exposed to extremely high static electrical charges. The A6812- devices combine a 20-bit CMOS shift register, accompanying data latches and control circuitry with bipolar sourcing outputs and pnp active pull downs. Designed primarily to drive vacuum-fluorescent displays, the 60 V and -40 mA output ratings also allow these devices to be used in many other peripheral power driver applications. The A6812- features an increased data input rate (compared with the older UCN/UCQ5812-F) and a controlled output slew rate. The CMOS shift register and latches allow direct interfacing with microprocessor-based systems. With a 3.3 V or 5 V logic supply, they will operate to at least 10 MHz. A CMOS serial data output permits cascade connections in applications requiring additional drive lines. Similar devices are available as the A6809- and A6810- (10 bits), A6811- (12 bits), and A6818- (32 bits). The A6812- output source drivers are npn Darlingtons, capable of sourcing up to 40 mA. The controlled output slew rate reduces electromagnetic noise, which is an important consideration in systems that include telecommunications and/or microprocessors and to meet government emissions regulations. For inter-digit blanking, all output drivers can be disabled and all sink drivers turned on with a BLANKING input high. The pnp active pull-downs will sink at least 2.5 mA. Two temperature ranges are available for optimum performance in commercial (suffix S-) or industrial (suffix E-) applications. Package styles are provided for through-hole DIP (suffix -A), surface-mount SOIC (suffix -LW), or minimum-area surface-mount PLCC (suffix -EP). Copper lead frames, low logic-power dissipation, and low output-saturation voltages allow these drivers to source 25 mA from all outputs continuously to more than +43C (suffix -LW), +61C (suffix -EP), or +77C (suffix -A). FEATURES Controlled Output Slew Rate Low Output-Saturation Voltages High-Speed Data Storage Low-Power CMOS Logic 60 V Minimum and Latches Output Breakdown Improved Replacements High Data Input Rate for TL5812-, UCN5812-, PNP Active Pull-Downs and UCQ5812- Complete part number includes a suffix to identify operating temperature range (E- or S-) and package type (-A, -EP, or -LW). Always order by complete part number, e.g., A6812SLW . 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER OUT20 SERIAL DATA OUT LOAD SUPPLY LOGIC SUPPLY SERIAL DATA IN OUT 1 3 2 1 V DD 28 27 26 VBB OUT19 LOGIC SUPPLY 2 27 SERIAL DATA IN OUT 20 3 26 OUT 1 OUT 19 4 25 OUT 2 1 SERIAL DATA OUT VBB VDD OUT 3 7 23 OUT 17 6 23 OUT 4 22 OUT 16 7 22 OUT 5 9 21 OUT 15 8 21 OUT 6 10 20 OUT 14 9 20 OUT 7 11 19 OUT 13 10 19 OUT 8 OUT 12 11 18 OUT 9 OUT 11 12 17 OUT 10 BLANKING 13 ST 28 16 STROBE GROUND 14 CLK 27 15 CLOCK REGISTER 18 OUT9 17 OUT10 REGISTER ST 16 STROBE CLK 15 CLOCK 14 GROUND 13 12 OUT11 OUT 8 LATCHES 24 LATCHES 5 OUT 2 REGISTER OUT 18 LATCHES 24 REGISTER 6 LATCHES 25 8 BLNK Dwg. PP-059-1 TYPICAL INPUT CIRCUIT Dwg. PP-029-8 VDD J A 55 C /W 'LW ', R J 1.0 /W C 45 SU FF IX 1.5 = = OUTN 'E P' ,R A V BB 2.0 J TYPICAL OUTPUT DRIVER SU FF IX ', R 'A Dwg. EP-010-5 2.5 IX FF SU IN ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS OUT12 28 LOAD SUPPLY 5 BLANKING OUT18 A6812xLW 4 A6812xEP A = 66 C /W 0.5 0 25 50 75 100 125 AMBIENT TEMPERATURE IN C 150 Dwg. GP-024-2 Dwg. EP-021-19 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 2000, Allegro MicroSystems, Inc. 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER FUNCTIONAL BLOCK DIAGRAM LOGIC SUPPLY V DD CLOCK SERIAL DATA IN SERIAL-PARALLEL SHIFT REGISTER STROBE LATCHES SERIAL DATA OUT BLANKING MOS BIPOLAR LOAD SUPPLY VBB GROUND OUT 1 OUT 2 OUT 3 OUT N Dwg. FP-013-1 TRUTH TABLE Serial Shift Register Contents Data Clock Input Input I1 I2 I3 ... IN-1 IN Serial Data Strobe Output Input Latch Contents I1 I2 I3 ... IN-1 Output Contents IN Blanklng I1 I2 I3 ... IN-1 IN H H R1 R2 ... RN-2 RN-1 RN-1 L L R1 R2 ... RN-2 RN-1 RN-1 X R1 R2 R3 ... RN-1 RN RN X X X L R1 R2 R3 ... RN-1 RN PN H P1 P2 P3 ... PN-1 PN L P1 P2 P3 ... PN-1 PN X X H L X X ... P1 P2 P3 ... L = Low Logic Level X PN-1 PN H = High Logic Level www.allegromicro.com X = Irrelevant X P = Present State X ... X R = Previous State L L ... L L 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER ELECTRICAL CHARACTERISTICS at TA = +25C (A6812S-) or over operating temperature range (A6812E-), VBB = 60 V unless otherwise noted. Limits @ VDD = 3.3 V Characteristic Output Leakage Current Symbol ICEX Test Conditions VOUT = 0 V Limits @ VDD = 5 V Mln. Typ. Max. Min. Typ. Max. Units -- <-0.1 -15 -- <-0.1 -15 A 57.5 58.3 -- 57.5 58.3 -- V VOUT(1) IOUT = -25 mA VOUT(0) IOUT = 1 mA -- 1.0 1.5 -- 1.0 1.5 V Output Pull-Down Current IOUT(0) VOUT = 5 V to VBB 2.5 5.0 -- 2.5 5.0 -- mA Input Voltage VIN(1) 2.2 -- -- 3.3 -- -- V VIN(0) -- -- 1.1 -- -- 1.7 V Output Voltage Input Current Input Clamp Voltage Serial Data Output Voltage Maximum Clock Frequency Logic Supply Current IIN(1) VIN = VDD -- <0.01 1.0 -- <0.01 1.0 A IIN(0) VIN = 0 V -- <-0.01 -1.0 -- <-0.01 -1.0 A IIN = -200 A -- -0.8 -1.5 -- -0.8 -1.5 V VOUT(1) IOUT = -200 A 2.8 3.05 -- 4.5 4.75 -- V VOUT(0) IOUT = 200 A -- 0.15 0.3 -- 0.15 0.3 V 10* -- -- 10* -- -- MHz VIK fc IDD(1) All Outputs High -- 0.25 0.75 -- 0.3 1.0 mA IDD(0) All Outputs Low -- 0.25 0.75 -- 0.3 1.0 mA IBB(1) All Outputs High, No Load -- 3.0 6.0 -- 3.0 6.0 mA IBB(0) All Outputs Low -- 0.2 20 -- 0.2 20 A tdis(BQ) CL = 30 pF, 50% to 50% -- 0.7 2.0 -- 0.7 2.0 s ten(BQ) CL = 30 pF, 50% to 50% -- 1.8 3.0 -- 1.8 3.0 s tp(STH-QL) RL = 2.3 k, CL 30 pF -- 0.7 2.0 -- 0.7 2.0 s tp(STH-QH) RL = 2.3 k, CL 30 pF -- 1.8 3.0 -- 1.8 3.0 s Output Fall Time tf RL = 2.3 k, CL 30 pF 2.4 -- 12 2.4 -- 12 s Output Rise Time tr RL = 2.3 k, CL 30 pF 2.4 -- 12 2.4 -- 12 s Output Slew Rate dV/dt RL = 2.3 k, CL 30 pF 4.0 -- 20 4.0 -- 20 V/s IOUT = 200 A -- 50 -- -- 50 -- ns Load Supply Current Blanking-to-Output Delay Strobe-to-Output Delay Clock-to-Serial Data Out Delay tp(CH-SQX) Negative current is defined as coming out of (sourcing) the specified device terminal. Typical data is is for design information only and is at TA = +25C. * Operation at a clock frequency greater than the specified minimum is possible but not warranteed. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER TIMING REQUIREMENTS and SPECIFICATIONS (Logic Levels are VDD and Ground) C 50% CLOCK A SERIAL DATA IN B DATA 50% t p(CH-SQX) SERIAL DATA OUT DATA 50% D E 50% STROBE BLANKING LOW = ALL OUTPUTS ENABLED t p(STH-QH) t p(STH-QL) 90% DATA OUT N 10% Dwg. WP-029 HIGH = ALL OUTPUTS BLANKED (DISABLED) BLANKING 50% t dis(BQ) t en(BQ) tr tf 90% OUT N 10% DATA Dwg. WP-030 A. Data Active Time Before Clock Pulse (Data Set-Up Time), tsu(D) ...................................... 25 ns B. Data Active Time After Clock Pulse (Data Hold Time), th(D) ............................................ 25 ns C. Clock Pulse Width, tw(CH) ............................................ 50 ns D. Time Between Clock Activation and Strobe, tsu(C) .... 100 ns E. Strobe Pulse Width, tw(STH) .......................................... 50 ns NOTE - Timing is representative of a 10 MHz clock. Higher speeds may be attainable with increased supply voltage; operation at high temperatures will reduce the specified maximum clock frequency. Serial Data present at the input is transferred to the shift register on the logic "0" to logic "1" transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift www.allegromicro.com data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. Information present at any register is transferred to the respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. When the BLANKING input is high, the output source drivers are disabled (OFF); the pnp active pull-down sink drivers are ON. The information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches. 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6812EA & A6812SA Dimensions in Inches (controlling dimensions) 28 0.015 0.008 15 0.700 MAX 0.580 0.485 0.600 BSC 1 2 0.070 0.030 3 14 0.100 4 1.565 1.380 0.005 MIN BSC 0.250 MAX 0.200 0.115 0.015 MIN 0.022 0.014 Dwg. MA-003-28 in Dimensions in Millimeters (for reference only) 28 0.381 0.204 15 17.78 MAX 14.73 12.32 15.24 BSC 1 2 1.77 0.77 3 14 2.54 4 39.7 35.1 BSC 0.13 MIN 6.35 MAX 0.39 5.08 2.93 MIN 0.558 0.356 NOTES: 1. 2. 3. 4. Dwg. MA-003-28 mm Exact body and lead configuration at vendor's option within limits shown. Lead spacing tolerance is non-cumulative. Lead thickness is measured at seating plane or below. Supplied in standard sticks/tubes of 12 devices. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6812EEP & A6812SEP (add "TR" to part number for tape and reel) Dimensions in Inches (controlling dimensions) 18 0.013 0.021 12 19 0.219 0.191 11 0.026 0.032 0.456 0.450 INDEX AREA 0.495 0.485 0.050 BSC 0.219 0.191 25 5 26 0.020 28 1 4 0.456 0.450 0.495 0.485 MIN 0.165 0.180 Dwg. MA-005-28A in Dimensions in Millimeters (for reference only)) 18 0.331 0.533 12 19 5.56 4.85 11 0.812 0.661 11.58 11.43 12.57 12.32 1.27 INDEX AREA BSC 5.56 4.85 25 5 26 0.51 MIN 4.57 4.20 28 1 4 11.582 11.430 12.57 12.32 Dwg. MA-005-28A mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 38 devices or add "TR" to part number for tape and reel. www.allegromicro.com 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6812ELW & A6812SLW (add "TR" to part number for tape and reel) Dimensions in Inches (for reference only) 28 15 0.0125 0.0091 0.419 0.394 0.2992 0.2914 0.050 0.016 0.020 0.013 1 2 0.050 3 0.7125 0.6969 0 TO 8 BSC 0.0926 0.1043 0.0040 MIN. Dwg. MA-008-28A in Dimensions in Millimeters (controlling dimensions) 28 15 0.32 0.23 10.65 10.00 7.60 7.40 1.27 0.40 0.51 0.33 1 2 1.27 3 18.10 17.70 BSC 0 TO 8 2.65 2.35 0.10 MIN. Dwg. MA-008-28A mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 27 devices or add "TR" to part number for tape and reel. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. www.allegromicro.com 6812 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER POWER INTERFACE DRIVERS Function Output Ratings* Part Number SERIAL-INPUT LATCHED DRIVERS 8-Bit (saturated drivers) 8-Bit 8-Bit 8-Bit 8-Bit 8-Bit (constant-current LED driver) 8-Bit (DMOS drivers) 8-Bit (DMOS drivers) 8-Bit (DMOS drivers) -120 mA 350 mA 350 mA 350 mA 350 mA 75 mA 250 mA 350 mA 100 mA 50 V 50 V 80 V 50 V 80 V 17 V 50 V 50 V 50 V 5895 5821 5822 5841 5842 6275 6595 6A595 6B595 10-Bit (active pull-downs) -25 mA 60 V 5810-F and 6809/10 12-Bit (active pull-downs) -25 mA 60 V 5811 and 6811 75 mA 17 V 6276 20-Bit (active pull-downs) -25 mA 60 V 5812-F and 6812 32-Bit (active pull-downs) 32-Bit 32-Bit (saturated drivers) -25 mA 100 mA 100 mA 60 V 30 V 40 V 5818-F and 6818 5833 5832 16-Bit (constant-current LED driver) PARALLEL-INPUT LATCHED DRIVERS 4-Bit 350 mA 50 V 5800 8-Bit 8-Bit 8-Bit (DMOS drivers) 8-Bit (DMOS drivers) -25 mA 350 mA 100 mA 250 mA 60 V 50 V 50 V 50 V 5815 5801 6B273 6273 SPECIAL-PURPOSE DEVICES Unipolar Stepper Motor Translator/Driver Addressable 8-Bit Decoder/DMOS Driver Addressable 8-Bit Decoder/DMOS Driver Addressable 8-Bit Decoder/DMOS Driver Addressable 28-Line Decoder/Driver 1.25 A 250 mA 350 mA 100 mA 450 mA 50 V 50 V 50 V 50 V 30 V 5804 6259 6A259 6B259 6817 * Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits. Negative current is defined as coming out of (sourcing) the output. Complete part number includes additional characters to indicate operating temperature range and package style. Internal transient-suppression diodes included for inductive-load protection. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000