82540EP Gigabit Ethernet Controller Networking Silicon Datasheet Product Features PCI Bus -- PCI Revision 2.3 support for 32-bit wide interface at 33 MHz and 66 MHz -- Algorithms that optimally use advanced PCI, MWI, MRM, and MRL commands -- CardBus Information Services (CIS) Pointer -- CLK_RUN# Signal MAC Specific -- Low-latency transmit and receive queues -- IEEE 802.3x-compliant flow-control support with software-controllable thresholds -- Caches up to 64 packet descriptors in a single burst -- Programmable host memory receive buffers (256 B to 16 KB) and cache line size (16 B to 256 B) -- Wide, optimized internal data path architecture -- 64 KB configurable Transmit and Receive FIFO buffers PHY Specific -- Integrated for 10/100/1000 Mb/s operation -- IEEE 802.3ab Auto-Negotiation support -- IEEE 802.3ab PHY compliance and compatibility. State-of-the-art DSP architecture implements digital adaptive equalization, echo cancellation, and crosstalk cancellation -- Automatic detection of cable lengths and MDI vs. MDI-X cable at all speeds Host Off-Loading -- Transmit and receive IP, TCP, and UDP checksum off-loading capabilities -- Transmit TCP segmentation -- Advanced packed filtering -- Jumbo frame support up to 16 KB -- IEEE 802.1q VLAN support with VLAN tag insertion, stripping and packet filtering for up to 4096 VLAN tags -- Descriptor ring management hardware for transmit and receive -- Interrupt coalescing (multiple packets per interrupt) Manageability -- Manageability features: Onboard SMB port, ASF 1.0, ACPI, Wake on LAN, and PXE -- Compliance with PCI Power Management 1.1 and ACPI 2.0 register set compliant -- SNMP and RMON statistic counters -- SDG 3.0, WfM 2.0, and PC2001 compliance Additional Device -- Four activity and link indication outputs that directly drive LEDs -- JTAG (IEEE 1149.1) Test Access Port built in silicon -- Internal PLL for clock generation can use a 25 MHz crystal -- Programmable LED functionality -- Industrial temperature support (-40 to +85 C) 317887-001 Revision 1.9 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The Intel products referenced in this document may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from: Intel Corporation P.O. Box 5937 Denver, CO 80217-9808 or call in North America 1-800-548-4725, Europe 44-0-1793-431-155, France 44-0-1793-421-777, Germany 44-0-1793-421-333, other Countries 708296-9333 Intel(R) is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) Intel Corporation, 2002-2007 ii Networking Silicon -- 82540EP Revision History Date Revision Notes Apr 2002 0.25 Initial Release Nov 2002 1.0 Changed document status to Intel Confidential. Jan 2003 1.1 Section 1.0. Replaced Block Diagram Section 2.6. Added Table footnote Section 4.1, 4.2, 4.3. Replaced tables Section 5.1. Added Visual Pin Reference Section 4.4 Removed Power Supply Characteristics; added note to I/O Characteristics Section 5.0 Replaced Pinout Diagram Apr 2003 1.2 Removed confidential status. Section 1.0. Added product ordering code. Oct 2003 1.3 Updated Table 8 to reflect correct values for internal pull-up impedance. Nov 2004 1.4 Added product features to cover. Updated signal names to match design guide and reference schematics. Nov 2004 1.5 Added information about migrating from a 2-layer 0.36 mm wide-trace substrate to a 2-layer 0.32 mm wide-trace substrate. Refer to the section on Package and Pinout Information. Added statement that no changes to existing soldering processes are needed for the 2-layer 0.32 mm wide-trace substrate change in the section describing "Package Information". Corrected pinout discrepancies between Tables 35 and 36. July 2006 1.6 Added LAN-disable description to the FLSH_SO signal description in Section 3. Sept 2006 1.7 Added industrial temperature values to "Product Features" and Table 2. Added a note to Figure 12 clarifying the device pin 1 location. Feb 2007 1.8 Updated Section 5.3 "Thermal Specifications". Sept 2007 1.9 Updated ball G13 description to 1.5V. Updated Figure 12 (changed G13 description to 1.5V). iii 82540EP -- Networking Silicon Note: iv This page intentionally left blank. Networking Silicon -- 82540EP Contents 1.0 Introduction.................................................................................... 1 1.1 1.2 1.3 Document Scope .................................................................................................. 1 Reference Documents .......................................................................................... 2 Block Diagram ...................................................................................................... 3 2.0 Product Code ................................................................................. 5 3.0 Signal Descriptions ....................................................................... 7 3.1 3.2 Signal Type Definitions ......................................................................................... 7 PCI Bus Interface.................................................................................................. 7 3.2.1 PCI Address, Data and Control Signals................................................... 7 3.2.2 Arbitration Signals.................................................................................... 9 3.2.3 Interrupt Signal ........................................................................................ 9 3.2.4 System Signals ........................................................................................ 9 3.2.5 Error Reporting Signals ........................................................................... 9 3.2.6 Power Management Signals.................................................................. 10 3.2.7 Impedance Compensation Signals ........................................................ 10 3.2.8 SMB Signals .......................................................................................... 10 EEPROM and Serial FLASH Interface Signals................................................... 10 Miscellaneous Signals ........................................................................................ 11 3.4.1 LED Signals ........................................................................................... 11 3.4.2 Other Signals ......................................................................................... 11 PHY Signals........................................................................................................ 12 3.5.1 Crystal Signals....................................................................................... 12 3.5.2 Analog Signals....................................................................................... 12 Test Interface Signals ......................................................................................... 13 Power Supply Connections................................................................................. 13 3.7.1 Digital Supplies ...................................................................................... 13 3.7.2 Analog Supplies..................................................................................... 13 3.7.3 Ground and No Connects ...................................................................... 14 3.7.4 Control Signals ...................................................................................... 14 3.3 3.4 3.5 3.6 3.7 4.0 Voltage, Temperature, and Timing Specifications ................... 15 4.1 4.2 4.3 4.4 4.5 Absolute Maximum Ratings ................................................................................ 15 Recommended Operating Conditions................................................................. 15 DC Specifications ............................................................................................... 16 AC Characteristics .............................................................................................. 19 Timing Specifications.......................................................................................... 20 4.5.1 PCI Bus Interface................................................................................... 20 4.5.2 Link Interface Timing ............................................................................. 24 4.5.3 EEPROM Interface ................................................................................ 25 v 82540EP -- Networking Silicon 5.0 Package and Pinout Information ................................................27 5.1 5.2 5.3 5.4 5.5 Device Identification ...........................................................................................27 Package Information............................................................................................28 Thermal Specifications ........................................................................................29 Pinout Information ...............................................................................................30 Visual Pin Reference ...........................................................................................39 vi Networking Silicon -- 82540EP 1.0 Introduction The Intel(R) 82540EP Gigabit Ethernet Controller is a single, compact component with an integrated Gigabit Ethernet Media Access Control (MAC) and physical layer (PHY) functions. For desktop, workstation and mobile PC Network designs with critical space constraints, the Intel(R) 82540EP allows for a Gigabit Ethernet implementation in a very small area that is footprint compatible with current generation 10/100 Mbps Fast Ethernet designs The Intel(R) 82540EP integrates Intel's fourth generation gigabit MAC design with fully integrated, physical layer circuitry to provide a standard IEEE 802.3 Ethernet interface for 1000BASE-T, 100BASE-TX, and 10BASE-T applications (802.3, 802.3u, and 802.3ab). The controller is capable of transmitting and receiving data at rates of 1000 Mbps, 100 Mbps, or 10 Mbps. In addition to managing MAC and PHY layer functions, the controller provides a 32-bit wide direct Peripheral Component Interconnect (PCI) 2.2 compliant interface capable of operating at 33 or 66 MHz. The 82540EP also incorporates the CLK_RUN# protocol and hardware supported downshift capability to two or three-pair 100 Mb/s operation. These features optimize mobile applications. The Intel(R) 82540EP's on-board System Management Bus (SMB) port enables network manageability implementations required by information technology personnel for remote control and alerting via the LAN. With SMB, management packets can be routed to or from a management processor. The SMB port enables industry standards, such as Intelligent Platform Management Interface (IPMI) and Alert Standard Forum (ASF), to be implemented using the 82540EP. In addition, on chip ASF 1.0 circuitry provides alerting and remote control capabilities with standardized interfaces. The 82540EP Gigabit Ethernet Controller architecture is designed to deliver high performance and PCI bus efficiency. Wide internal data paths eliminate performance bottlenecks by efficiently handling large address and data words. The 82540EP controller includes advanced interrupt handling features to limit PCI bus traffic and a PCI interface that maximizes the use of bursts for efficient bus usage. The 82540EP caches up to 64 packet descriptors in a single burst for efficient PCI bandwidth use. A large 64 KByte on-chip packet buffer maintains superior performance as available PCI bandwidth changes. In addition, using hardware acceleration, the controller offloads tasks from the host controller, such as TCP/UDP/IP checksum calculations and TCP segmentation. The 82540EP is packaged in a 15 mm2 196-ball grid array and is pin compatible with both the 82551QM 10/100 Mbps Fast Ethernet Multifunction PCI/CardBus Controller and the 82540EM Gigabit Ethernet Controller (which does not have added power saving features like CLK_RUN#). 1.1 Document Scope This document contains datasheet specifications for the 82540EP Gigabit Ethernet Controller, including signal descriptions, DC and AC parameters, packaging data, and pinout information. 1 82540EP -- Networking Silicon 1.2 Reference Documents This application assumes that the designer is acquainted with high-speed design and board layout techniques. The following documents provide additional information: * 82544EI/82544GC Gigabit Ethernet Controller Software Developer's Manual, Revision 0.25, Intel Corporation. * * * * * * * PCI Local Bus Specification, Revision 2.3, PCI Special Interest Group. PCI Bus Power Management Interface Specification, Rev. 1.1, PCI Special Interest Group. IEEE Standard 802.3, 1996 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3u, 1995 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3x, 1997 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3z, 1998 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3ab, 1999 Edition, Institute of Electrical and Electronics Engineers (IEEE). * Intel Ethernet Controllers Timing Device Selection Guide, AP-419, Intel Corporation. * PCI Mobile Design Guide, Rev. 1.1, PCI Special Interest Group * 82540EP/82541(PI/GI/EI) & 82562EZ(EX) Dual Footprint Design Guide, AP-444. Intel Corporation. 2 Networking Silicon -- 82540EP Block Diagram 1.3 PCI i/f PCI I/F ACPI Target Control LED ASF PHY GMII MAC Core TX MAC TX Link RX Data Statistics Filter RX MAC CSR Register Access RX Data Mgmt FIFOs SMBus Interface Manageability MDIO Tx Arb 82540EP Architecture Flash Interface Flash TX Out Flow Ctrl RX In CSR Register Access Control, Status & Interrupt Registers Target Logic DMA TX descriptor TX engine FIFOs RX descriptor RX engine FIFOs 64K bytes Packet Buffer Interface Packet Buffer TX Data PCI Core Master write FIFO Master read FIFO (Many blocks) Clock / Reset HW Default Configs 4-wire EEPROM Interface EEPROM Data Alignment MDI (Copper) Interface Figure 1. Gigabit Ethernet Controller Block Diagram 3 82540EP -- Networking Silicon Note: 4 This page is intentionally left blank. Networking Silicon -- 82540EP 2.0 Product Code The product ordering code for the 82540EP is: RC82540EP. 5 82540EP -- Networking Silicon Note: 6 This page intentionally left blank. Networking Silicon -- 82540EP 3.0 Signal Descriptions Note: 3.1 The targeted signal names are subject to change without notice. Verify with your local Intel sales office that you have the latest information before finalizing a design. Signal Type Definitions The signals of the 82540EP controller are electrically defined as follows: Name Definition I Input. Standard input only digital signal. O Output. Standard output only digital signal. TS Tri-state. Bi-directional three-state digital input/output signal. Sustained Tri-state. Sustained digital three-state signal driven by one agent at a time. STS An agent driving the STS pin low must actively drive it high for at least one clock before letting it float. The next agent of the signal cannot drive the pin earlier than one clock after it has been released by the previous agent. Open Drain. Wired-OR with other agents. 3.2 OD The signaling agent asserts the OD signal, but the signal is returned to the inactive state by a weak pull-up resistor. The pull-up resistor may require two or three clock periods to fully restore the signal to the de-asserted state. A Analog. PHY analog data signal. P Power. Power connection, voltage reference, or other reference connection. PCI Bus Interface When the Reset signal (RST#) is asserted, the 82540EP will not drive any PCI output or bidirectional pins except the Power Management Event signal (PME#). 3.2.1 PCI Address, Data and Control Signals Symbol AD[31:0] Type TS Name and Function Address and Data. Address and data signals are multiplexed on the same PCI pins. A bus transaction includes an address phase followed by one or more data phases. The address phase is the clock cycle when the Frame signal (FRAME#) is asserted low. During the address phase AD[31:0] contain a physical address (32 bits). For I/O, this is a byte address, and for configuration and memory, a DWORD address. The 82540EP device uses little endian byte ordering. During data phases, AD[7:0] contain the least significant byte (LSB) and AD[31:24] contain the most significant byte (MSB). 7 82540EP -- Networking Silicon Symbol C/BE#[3:0] Type TS Name and Function Bus Command and Byte Enables. Bus command and byte enable signals are multiplexed on the same PCI pins. During the address phase of a transaction, C/ BE#[3:0] define the bus command. In the data phase, C/BE#[3:0] are used as byte enables. The byte enables are valid for the entire data phase and determine which byte lanes contain meaningful data. C/BE#[0] applies to byte 0 (LSB) and C/BE#[3] applies to byte 3 (MSB). PAR TS Parity. The Parity signal is issued to implement even parity across AD[31:0] and C/ BE#[3:0]. PAR is stable and valid one clock after the address phase. During data phases, PAR is stable and valid one clock after either IRDY# is asserted on a write transaction or TRDY# is asserted after a read transaction. Once PAR is valid, it remains valid until one clock after the completion of the current data phase. When the 82540EP controller is a bus master, it drives PAR for address and write data phases, and as a slave device, drives PAR for read data phases. FRAME# IRDY# 8 STS STS Cycle Frame. The Frame signal is driven by the 82540EP device to indicate the beginning and length of an access and indicate the beginning of a bus transaction. While FRAME# is asserted, data transfers continue. FRAME# is de-asserted when the transaction is in the final data phase. Initiator Ready. Initiator Ready indicates the ability of the 82540EP controller (as bus master device) to complete the current data phase of the transaction. IRDY# is used in conjunction with the Target Ready signal (TRDY#). The data phase is completed on any clock when both IRDY# and TRDY# are asserted. During the write cycle, IRDY# indicates that valid data is present on AD[31:0]. For a read cycle, it indicates the master is ready to accept data. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. The 82540EP controller drives IRDY# when acting as a master and samples it when acting as a slave. Target Ready. The Target Ready signal indicates the ability of the 82540EP controller (as a selected device) to complete the current data phase of the transaction. TRDY# is used in conjunction with the Initiator Ready signal (IRDY#). A data phase is completed on any clock when both TRDY# and IRDY# are sampled asserted. TRDY# STS STOP# STS Stop. The Stop signal indicates the current target is requesting the master to stop the current transaction. As a slave, the 82540EP controller drives STOP# to request the bus master to stop the transaction. As a master, the 82540EP controller receives STOP# from the slave to stop the current transaction. IDSEL# I Initialization Device Select. The Initialization Device Select signal is used by the 82540EP as a chip select signal during configuration read and write transactions. DEVSEL# STS Device Select. When the Device Select signal is actively driven by the 82540EP, it signals notifies the bus master that it has decoded its address as the target of the current access. As an input, DEVSEL# indicates whether any device on the bus has been selected. VIO P During a read cycle, TRDY# indicates that valid data is present on AD[31:0]. For a write cycle, it indicates the target is ready to accept data. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. The 82540EP device drives TRDY# when acting as a slave and samples it when acting as a master. VIO. The VIO signal is a voltage reference for the PCI interface (3.3 V or 5 V PCI signaling environment). It is used as the clamping voltage. Note: An external resistor is required between the voltage reference and the VIO pin. The target resistor value is 100 K Networking Silicon -- 82540EP 3.2.2 Arbitration Signals Symbol 3.2.3 Name and Function REQ# TS Request Bus. The Request Bus signal is used to request control of the bus from the arbiter. This signal is point-to-point. GNT# I Grant Bus. The Grant Bus signal notifies the 82540EP that bus access has been granted. This is a point-to-point signal. LOCK# I Lock Bus. The Lock Bus signal is asserted by an initiator to require sole access to a target memory device during two or more separate transfers. The 82540EP device does not implement bus locking. Interrupt Signal Symbol INTA# 3.2.4 Type Type TS Name and Function Interrupt A. Interrupt A is used to request an interrupt by port 1 of the 82540EP. It is an active low, level-triggered interrupt signal. System Signals Symbol Type Name and Function CLK I PCI Clock. The PCI Clock signal provides timing for all transactions on the PCI bus and is an input to the 82540EP device. All other PCI signals, except the Interrupt A (INTA#) and PCI Reset signal (RST#), are sampled on the rising edge of CLK. All other timing parameters are defined with respect to this edge. M66EN I 66 MHz Enable. M66EN indicates whether the system bus is enabled for 66 MHz. I PCI Reset. When the PCI Reset signal is asserted, all PCI output signals, except the Power Management Event signal (PME#), are floated and all input signals are ignored. The PME# context is preserved, depending on power management settings. RST# Most of the internal state of the 82540EP is reset on the de-assertion (rising edge) of RST#. CLK_RUN# 3.2.5 I/O OD Clock Run. This signal is used by the system to pause the PCI clock signal. It is used by the 82540EP controller to request the PCI clock. When the CLK_RUN# feature is disabled, leave this pin unconnected. Error Reporting Signals Symbol SERR# PERR# Type Name and Function OD System Error. The System Error signal is used by the 82540EP controller to report address parity errors. SERR# is open drain and is actively driven for a single PCI clock when reporting the error. STS Parity Error. The Parity Error signal is used by the 82540EP controller to report data parity errors during all PCI transactions except by a Special Cycle. PERR# is sustained tri-state and must be driven active by the 82540EP controller two data clocks after a data parity error is detected. The minimum duration of PERR# is one clock for each data phase a data parity error is present. 9 82540EP -- Networking Silicon 3.2.6 Power Management Signals Symbol LAN_ PWR_ GOOD 3.2.7 Power Good (Power-on Reset). The Power Good signal is used to indicate that stable power is available for the 82540EP. When the signal is low, the 82540EP holds itself in reset state and floats all PCI signals. PME# OD Power Management Event. The 82540EP device drives this signal low when it receives a wake-up event and either the PME Enable bit in the Power Management Control/Status Register or the Advanced Power Management Enable (APME) bit of the Wake-up Control Register (WUC) is 1b. AUX_PWR I Auxiliary Power. If the Auxiliary Power signal is high, then auxiliary power is available and the 82540EP device should support the D3cold power state. Impedance Compensation Signals Name and Function I/O N Device Impedance Compensation. This signal should be connected to an external precision resistor (to VDD) that is indicative of the PCI trace load. This cell is used to dynamically determine the drive strength required on the N-channel transistors in the PCI I/O cells. ZP_COMP I/O P Device Impedance Compensation. This signal should be connected to an external precision resistor (to VSS) that is indicative of the PCI trace load. This cell is used to dynamically determine the drive strength required on the P-channel transistors in the PCI I/O cells. SMB Signals Type Name and Function SMBCLK I/O SMB Clock. The SMB Clock signal is an open drain signal for serial SMB interface. SMBDATA I/O SMB Data. The SMB Data signal is an open drain signal for serial SMB interface. SMB_ ALERT# O SMB Alert. The SMB Alert signal is open drain for serial SMB interface. EEPROM and Serial FLASH Interface Signals Symbol 10 Type ZN_COMP Symbol 3.3 Name and Function I Symbol 3.2.8 Type Type Name and Function EEDI O EEPROM Data Input. The EEPROM Data Input pin is used for output to the memory device. EEDO I EEPROM Data Output. The EEPROM Data Output pin is used for input from the memory device. The EE_DO includes an internal pull-up resistor. EECS O EEPROM Chip Select. The EEPROM Chip Select signal is used to enable the device. EESK O EEPROM Serial Clock. The EEPROM Shift Clock provides the clock rate for the EEPROM interface, which is approximately 1 MHz. Networking Silicon -- 82540EP Symbol Type Name and Function FL_CE# O FLASH Chip Enable Output. Used to enable FLASH device. FL_SCK O FLASH Serial Clock Output. The clock rate of the serial FLASH interface is approximately 1 MHz. FL_SI O FLASH Serial Data Input. This pin is an output to the memory device. FLASH Serial Data Output. This pin is an input from the FLASH memory. FLSH_SO Note: I Note: The 82540EP LAN-disable mechanism is implemented using this pin. It is generally used when no Flash device is present (Flash disabled). If this pin is 1b (Vcc) then the 82540EP is enabled. If the pin is 0b (Vss) then the 82540EP is disabled. This signal should be sampled within 1s of the rising edge of LAN_PWR_GOOD and PCI_RST_N. Note that this pin also has an internal pull-up that is sufficient enough to enable the 82540EP if no Flash device is present. If the LAN-disable feature is used when a Flash device is present, then care must be taken by system designers not to drive the FLSH_SO pin while the Flash device is driving it. 3.4 Miscellaneous Signals 3.4.1 LED Signals Symbol 3.4.2 Type Name and Function LINK_UP# O LED0 / LINK Up. Programmable LED indication. Defaults to indicate link connectivity. ACTIVITY# O LED1 / Activity. Programmable LED indication. Defaults to flash to indicate transmit or receive activity. LINK100# O LED2 / LINK 100. Programmable LED indication. Defaults to indicate link at 100 Mbps. LINK1000# O LED3 / LINK 1000. Programmable LED indication. Defaults to indicate link at 1000 Mbps. Other Signals Symbol SDP[7:6] SDP[1:0] Type TS Name and Function Software Defined Pins. The Software Defined Pins are reserved and programmable with respect to input and output capability. These default to input signals upon power-up but may be configured differently by the EEPROM. The upper four bits may be mapped to the General Purpose Interrupt bits if they are configured as input signals. Note: SDP5 is not included in the group of Software Defined Pins. 11 82540EP -- Networking Silicon 3.5 PHY Signals 3.5.1 Crystal Signals Symbol 3.5.2 Type Name and Function XTAL1 I Crystal One. The Crystal One pin is a 25 MHz +/- 30 ppm input signal. It can be connected to either an oscillator or crystal. If a crystal is used, Crystal Two (XTAL2) must also be connected. XTAL2 O Crystal Two. Crystal Two is the output of an internal oscillator circuit used to drive a crystal into oscillation. If an external oscillator is used in the design, XTAL2 must be disconnected. Analog Signals Symbol REF Type P Name and Function Reference. This Reference signal should be connected to VSS through an external 2.49 K resistor. Media Dependent Interface [0]. 1000BASE-T: In MDI configuration, MDI[0]+/- corresponds to BI_DA+/-, and in MDI-X configuration, MDI[0]+/- corresponds to BI_DB+/-. MDI[0]+/- A 100BASE-TX: In MDI configuration, MDI[0]+/- is used for the transmit pair, and in MDI-X configuration, MDI[0]+/- is used for the receive pair. 10BASE-T: In MDI configuration, MDI[0]+/- is used for the transmit pair, and in MDI-X configuration, MDI[0]+/- is used for the receive pair. Media Dependent Interface [1]. 1000BASE-T: In MDI configuration, MDI[1]+/- corresponds to BI_DB+/-, and in MDI-X configuration, MDI[1]+/- corresponds to BI_DA+/-. MDI[1]+/- A 100BASE-TX: In MDI configuration, MDI[1]+/- is used for the receive pair, and in MDI-X configuration, MDI[1]+/- is used for the transit pair. 10BASE-T: In MDI configuration, MDI[1]+/- is used for the receive pair, and in MDI-X configuration, MDI[1]+/- is used for the transit pair. Media Dependent Interface [2]. 1000BASE-T: In MDI configuration, MDI[2]+/- corresponds to BI_DC+/-, and in MDI-X MDI[2]+/- A configuration, MDI[2]+/- corresponds to BI_DD+/-. 100BASE-TX: Unused. 10BASE-T: Unused. Media Dependent Interface [3]. 1000BASE-T: In MDI configuration, MDI[3]+/- corresponds to BI_DD+/-, and in MDI-X MDI[3]+/- A configuration, MDI[3]+/- corresponds to BI_DC+/-. 100BASE-TX: Unused. 10BASE-T: Unused. 12 Networking Silicon -- 82540EP 3.6 Test Interface Signals Symbol Type Name and Function JTAG_TCK I JTAG Clock. JTAG_TDI I JTAG TDI. JTAG_TDO O JTAG TDO. JTAG_TMS I JTAG TMS. JTAG_ TRST# I JTAG Reset. This is an active low reset signal for JTAG. This signal should be terminated using a pull-down resistor to ground. It must not be left unconnected. TEST I Factory Test Pin. CLK_VIEW O Clock View. Output for GTX_CLK and RX_CLK during IEEE PHY conformance testing. The clock is selected by register programming. ALTCLK_125 I CLK_BYP# I HSDACP I HSDACN I PHY_TSTPT I Alternate CLK125 Input. Factory use only. For normal component operation, connect to VSS. Clock Bypass Enable. Factory use only. For normal component operation, no connect. PHY High Speed Test Interface. Factory use only. For normal component operation, no connect. PHY High Speed Test Interface. Factory use only. For normal component operation, no connect. PHY Test Point. Factory use only. For normal component operation, no connect. 3.7 Power Supply Connections 3.7.1 Digital Supplies Symbol 3.7.2 Type Name and Function VDDO P 3.3 V I/O Power Supply. DVDD P 1.5 V Digital Core Power Supply. Analog Supplies Symbol Type Name and Function AVDDH P 3.3 V Analog Power Supply. AVDDL P 2.5 V Analog Power Supply. 13 82540EP -- Networking Silicon 3.7.3 Ground and No Connects Symbol 3.7.4 Name and Function GND P Ground. NC P No Connect. Do not connect any circuitry to these pins. Pull-up or pull-down resistors should not be connected to these pins. Control Signals Symbol CTRL15 CTRL25 14 Type Type Name and Function A 1.5V Control. LDO voltage regulator output to drive external pass transistor. If 1.5 V is already present in the system, leave output unconnected. To achieve optimal D3 power consumption (<50 mw), leave the output unconnected and use a high-efficiency external switching regulator. A 2.5V Control. LDO voltage regulator output to drive external pass transistor. If 2.5 V is already present in the system, leave output unconnected. To achieve optimal D3 power consumption (<50 mw), leave the output unconnected and use a high-efficiency external switching regulator. Networking Silicon -- 82540EP 4.0 Voltage, Temperature, and Timing Specifications Note: 4.1 Table 1. The specification values listed in this section are subject to change without notice. Verify with your local Intel sales office that you have the latest information before finalizing a design. Absolute Maximum Ratings Absolute Maximum Ratingsa Symbol Parameter Min Max Unit VDD DC supply voltage -0.3 7 V VIN Input voltage -1 VDD + 0.3 V IIN DC input pin current -10 10 mA TSTG Storage temperature -40 125 C a. Maximum ratings are referenced to ground (VSS). Permanent device damage is likely to occur if the ratings in this table are exceeded. These values should not be used as the limits for normal device operations. 4.2 Table 2. Recommended Operating Conditions Recommended Operating Conditionsa (Sheet 1 of 2) Symbol Parameter TOP Operating Temperature VIO VIO Voltage Range VDD Periphery Voltage Range Condition 3.3 V 10% Min Max Unit -40 85 C 3 5.25 V 3.6 V 3 Typ 3.3 15 82540EP -- Networking Silicon Table 2. Recommended Operating Conditionsa (Sheet 2 of 2) Symbol Parameter Condition Min Typ Max Unit VAH Analog High VDD Range 3.3 V 10% 3 3.3 3.6 V VD Core Digital Voltage Range 1.5 V 5% 1.425 1.5 1.575 V VAL Analog Low VDD Range 2.5 V 5% 2.375 2.5 2.625 V a. Sustained operation of the device at conditions exceeding these values, even if they are within the absolute maximum rating limits, might result in permanent damage. 4.3 Table 3. DC Specifications DC Characteristics Symbol Table 4. Parameter Min Typ Max Units VDD (3.3) DC supply voltage on VDDO or AVDDH 3.00 3.3 3.60 V VDD (2.5) DC supply voltage on AVDDL 2.38 2.5 2.62 V VDD (1.5) DC supply voltage on DVDD 1.43 1.5 1.57 V Power Specifications - D0a D0a unplugged/no link 16 @10 Mbps @100Mbps @1000Mbps Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 40 40 55 65 65 80 125 125 2.5 V 20 20 30 35 55 60 145 150 1.5 V 100 120 95 100 115 125 400 425 Total Device Power 325 mW 1.38 W 1.5 W 400 mW 525 mW Networking Silicon -- 82540EP Table 5. Power Specifications - D3cold D3cold - wake disabled - max power savings mode disabled D3cold - wake-up enabled unplugged/no link @10 Mbps @100Mbps D3cold - wake disabled - max power savings mode enableda Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 40 40 55 55 50 50 40 40 6 8 2.5 V 20 20 30 30 55 55 20 20 0.1 0.1 1.5 V 40 40 30 35 55 60 10 10 1 1 Total Device Power 240 mW 300 mW 385 mW 195 mW 20 mW a. Special Note: To obtain the benefit of max power savings mode, do not use the internal voltage regulator control circuit and external pass transistors. Use external switching regulators for highest efficiency. Table 6. Power Specifications D(r) Uninitialized D(r) Uninitialized (LAN_PWR_GOOD=0) Table 7. Typ Icc (mA) Max Icc (mA) 3.3 V 40 45 2.5 V 40 45 1.5 V 190 200 Total Device Power 520 mW Power Specifications - Complete Subsystem Complete Subsystem (Reference Design) Including Magnetics, LED, Regulator Circuits D3cold - wake disabled - max power savings mode disabled 3.3 V D3cold wakeenabled @10Mbps D3cold wakeenabled @100Mbps D0 @1000Mbps active D3cold - wake disabled - max power savings mode enabled Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 40 40 60 60 60 60 130 130 6 8 17 82540EP -- Networking Silicon Table 7. Power Specifications - Complete Subsystem 2.5 V 20 20 40 40 80 80 240 245 0.1 0.1 1.5 V 10 10 30 35 55 60 400 425 1 1 Subsystem 3.3 V current Table 8. 70 mA 135 mA 200 mA 800 mA 10 mA I/O Characteristics Symbol Parameter Condition Min Typ Max Unit 0.8 V VIL Voltage input LOW -0.5 VIH Voltage input HIGH 2 VOL Voltage output LOW VOH Voltage output HIGH 2.4 V VSH Schmitt Trigger Hysterysis 0.1 V VDD +0.3 0.4 V V Output current LOW IOLa 3mA drivers (TTL3) VOL 3 mA 6mA drivers (TTL6) VOL 6 mA 12mA drivers (TTL12) VOL 12 mA 3mA drivers (TTL3) VOH -3 mA 6mA drivers (TTL6) VOH -6 mA 12mA drivers (TTL12) VOH -12 mA VIN = VDD or VSS -10 Output current HIGH IOHa Input Current IIN TTL inputs Inputs with pull-down resistors VIN = VDD 150 TTL inputs with pull-up resistors VIN = VSS -150 -10 1 10 A 480 A -480 A 10 A IOZ 3-state output leakage current VOH = VDD or VSS CIN Input capacitance Any input and bi-directional buffer 2.5 pF Any output buffer 2 pF COUT Output capacitance CPUD Pull-up/down Resistor value 15 1 20 30 k a. TTL3 signals include: EE_DI, EE_SK, EE_CS, and JTAG_TDO. TTL6 signals include: CLKRUN#, FL_CE#, FL_SCK, FL_SI, and CLK_VIEW. TTL12 signals include: LED0 / LINK #, LED1 / ACT #, LED2 / LINK100 #, LED3 / LINK1000 #, SDP0, SDP1, SDP6, and SDP7. 18 Networking Silicon -- 82540EP 4.4 Table 9. AC Characteristics AC Characteristics: 3.3 V Interfacing Symbol CLK Parameter Min Typ Clock frequency in PCI mode Max Unit 66 MHz Table 10. 25 MHz Clock Input Requirements Parametera Symbol fi_TX_CLK TX_CLK_IN frequency Min Typ Max Unit 25 - 50 ppm 25 25 + 50 ppm MHz a. This parameter applies to an oscillator connected to the Crystal One (XTAL1) input. Alternatively, a crystal may be connected to XTAL1 and XTAL2 as the frequency source for the internal oscillator. Table 11. Link Interface Clock Requirements Symbol a fGTX Parameter Min GTX_CLK frequency Typ Max 125 Unit MHz a. GTX_CLK is used externally for test purposes only. Table 12. EEPROM Interface Clock Requirements Symbol Parameter Min Typ fSK Max Unit 1 MHz Table 13. AC Test Loads for General Output Pins Symbol Signal Name Value Units CL TDO 10 pF CL PME#, SDP[7:0] 16 pF CL EEDI, EESK 18 pF CL RX_ACTIVITY, TX_ACTIVITY, LINK_UP 20 pF 19 82540EP -- Networking Silicon Figure 1. AC Test Loads for General Output Pins CL 4.5 Timing Specifications Note: Timing specifications are subject to change. Verify with your local Intel sales office that you have the latest information before finalizing a design. 4.5.1 PCI Bus Interface 4.5.1.1 PCI Bus Interface Clock Table 14. PCI Bus Interface Clock Parameters PCI 66 MHz Symbol PCI 33 MHz Parametera Units Min Max Min 30 Max TCYC CLK cycle time 15 30 ns TH CLK high time 6 11 ns TL CLK low time 6 11 ns CLK slew rate 1.5 b RST# slew rate 50 4 1 50 4 V/ns mV/ns a. Rise and fall times are specified in terms of the edge rate measured in V/ns. This slew rate must be met across the minimum peak-to-peak portion of the clock waveform as shown. b. The minimum RST# slew rate applies only to the rising (de-assertion) edge of the reset signal and ensures that system noise cannot render a monotonic signal to appear bouncing in the switching range. 20 Networking Silicon -- 82540EP Figure 2. PCI Clock Timing Tcyc Th 0.6 Vcc 3.3 V Clock 0.5 Vcc 0.4 Vcc p-to-p (minimum) 0.4 Vcc 0.3 Vcc 0.2 Vcc Tl PCI Clock Timing.vsd 4.5.1.2 PCI Bus Interface Timing Table 15. PCI Bus Interface Timing Parameters PCI 66MHz Symbol PCI 33 MHz Parameter Units Min Max Min Max TVAL CLK to signal valid delay: bussed signals 2 6 2 11 ns TVAL(ptp) CLK to signal valid delay: pointto-point signals 2 6 2 12 ns TON Float to active delay 2 TOFF Active to float delay 28 ns TSU Input setup time to CLK: bussed signals 3 7 ns TSU(ptp) Input setup time to CLK: point-topoint signals 5 10, 12 ns TH Input hold time from CLK 0 0 ns TRRSU REQ64# to RST# setup time 10*TCYC 10*TCYC ns TRRH RST# to REQ64# hold time 0 0 ns 2 14 ns NOTES: 1. Output timing measurements are as shown. 2. REQ# and GNT# signals are point-to-point and have different output valid delay and input setup times than bussed signals. GNT# has a setup of 10 ns; REQ# has a setup of 12 ns. All other signals are bussed. 3. Input timing measurements are as shown. 21 82540EP -- Networking Silicon Figure 3. PCI Bus Interface Output Timing Measurement VTH PCI_CLK VTEST VTL Output Delay VTEST VSTEP (3.3V Signalling) output current leakage current Tri-State Output TON TOFF Figure 4. PCI Bus Interface Input Timing Measurement Conditions VTH PCI_CLK VTEST VTL TSU TH VTH Input VTEST Input Valid VTEST VMAX VTL Table 16. PCI Bus Interface Timing Measurement Conditions Symbol Parameter Unit VTH Input measurement test voltage (high) 0.6*VCC V VTL Input measurement test voltage (low) 0.2*VCC V VTEST Output measurement test voltage 0.4*VCC V 1.5 V/ns Input signal slew rate 22 PCI 66 MHz 3.3 v Networking Silicon -- 82540EP Figure 5. TVAL (max) Rising Edge Test Load Pin Test Point 1/2 inch max. 25 10 pF Figure 6. TVAL (max) Falling Edge Test Load Pin Test Point 1/2 inch max. 25 10 pF VCC Figure 7. TVAL (min) Test Load Pin Test Point 1/2 inch max. 1k 10 pF 1k VCC 23 82540EP -- Networking Silicon Figure 8. TVAL Test Load (PCI 5 V Signaling Environment) Pin Test Point 1/2 inch max. 50 pF NOTE: Note: 50 pF load used for maximum times. Minimum times are specified with 0 pF load. 4.5.2 Link Interface Timing Table 17. Rise and Fall Times Symbol Parameter Condition Min Unit TR Clock rise time 0.8 V to 2.0 V 0.7 ns TF Clock fall time 2.0 V to 0.8 V 0.7 ns TR Data rise time 0.8 to 2.0 V 0.7 ns TF Data fall time 2.0 V to 0.8 V 0.7 ns Figure 9. Link Interface Rise/Fall Timing 2.0 V 0.8 V TR 24 Max TF Networking Silicon -- 82540EP 4.5.3 EEPROM Interface Table 18. Link Interface Clock Requirements Symbol TPW Parameter Min Typ Max TPERIOD*128 EESK pulse width Unit ns a. The EEPROM clock is derived from a 125 MHz internal clock. Table 19. Link Interface Clock Requirements Symbol Parametera Min Typ Max Unit TDOS EEDO setup time TCYC*2 ns TDOH EEDO hold time 0 ns a. The EEDO setup and hold time is a function of the PCI bus CLK cycle time but is referenced to EESK. 25 82540EP -- Networking Silicon Note: 26 This page intentionally left blank. Networking Silicon -- 82540EP 5.0 Package and Pinout Information This section describes the 82540EP device, manufactured in a 196-lead ball grid array measuring 15mm x 15mm. External product identification is shown in Figure 10. The nominal ball pitch is 1mm. The pin number-to-signal mapping is indicated beginning with Table 19. 5.1 Device Identification Figure 10. 82540EP Device Identification Markings RC82540EP YYWW (c) 'ZZ Tnnnnnnnn Country 82540EP Product Name YYWW Date Code Tnnnnnnnn Lot Trace Code (c)'ZZ Copyright Information Country Country of Origin Assembly NOTE: "*"indicates the location of pin 1. It is not an actual mark on the device 27 82540EP -- Networking Silicon 5.2 Package Information The 82540EP device is a 196-lead ball grid array (TFBGA) measuring 15 mm2. The package dimensions are detailed in Figure 11. The nominal ball pitch is 1 mm. . Figure 11. Dimension Diagram for the 196-pin BGA 1.56 +/-0.19 0.85 0.40 +/-0.10 30 o Seating Plate 0.32 +/-0.04 Note: All dimensions are in millimeters. Substrate change from 0.36 mm to 0.32 mm Note: 28 No changes to existing soldering processes are needed for the 0.32 mm substrate change. Networking Silicon -- 82540EP 5.3 Thermal Specifications The 82540EP device is specified for operation when the ambient temperature (TA) is within the range of -40 C to 85 C. TC (case temperature) is calculated using the equation: TC = TA + P (JA - q JC) TJ (junction temperature) is calculated using the equation: TJ = TA + P JA P (power consumption) is calculated by using the typical ICC, as indicated in Table 4 of Section 4.0, and nominal VCC. The thermal resistances are shown in Table 18. Table 18. Thermal Characteristics Value at specified airflow (m/s) Symbol Parameter Units 0 1 2 3 JA Thermal resistance, junction-to-ambient 28.1 25.0 23.7 22.8 C/ Watt JC Thermal resistance, junction-to-case 6.1 6.1 6.1 6.1 C/ Watt Thermal resistances are determined empirically with test devices mounted on standard thermal test boards. Real system designs may have different characteristics due to board thickness, arrangement of ground planes, and proximity of other components. The case temperature measurements should be used to assure that the 82540EP device is operating under recommended conditions. 29 82540EP -- Networking Silicon 5.4 Pinout Information Table 19. PCI Address, Data, and Control Signals Signal Pin Signal Pin K1 Signal C/BE#[0] Pin AD[0] N7 AD[16] M4 AD[1] M7 AD[17] E3 C/BE#[1] L3 AD[2] P6 AD[18] D1 C/BE#[2] F3 AD[3] P5 AD[19] D2 C/BE#[3] C4 AD[4] N5 AD[20] D3 PAR J1 AD[5] M5 AD[21] C1 FRAME# F2 AD[6] P4 AD[22] B1 IRDY# F1 AD[7] N4 AD[23] B2 TRDY# G3 AD[8] P3 AD[24] B4 STOP# H1 AD[9] N3 AD[25] A5 DEVSEL# H3 AD[10] N2 AD[26] B5 VIO G2 AD[11] M1 AD[27] B6 IDSEL A4 AD[12] M2 AD[28] C6 AD[13] M3 AD[29] C7 AD[14] L1 AD[30] A8 AD[15] L2 AD[31] B8 Table 20. PCI Arbitration Signals Signal Pin REQ# C3 GNT# J3 Table 21. Interrupt Signals Signal INTA# Pin H2 Table 22. System Signals Signal CLK Pin G1 Signal M66EN Pin C2 Table 23. Error Reporting Signals Signal SERR# 30 Pin A2 Signal PERR# Pin J2 Signal RST# Pin B9 Networking Silicon -- 82540EP Table 24. Power Management Signals Signal Pin Signal Pin LAN_PWR_ GOOD A9 AUX_PWR J12 PME# A6 CLK_RUN# C8 Table 25. Impedance Compensation Signals Signal ZN_COMP Pin H4 Signal ZP_COMP Pin G4 Table 26. SMB Signals Signal SMBCLK Pin A10 Signal SMBDATA Pin C9 Signal SMB_ALERT# Pin B10 Table 27. EEPROM and Serial FLASH Interface Signals Signal Pin Signal Pin Signal Pin EESK M10 EEDI P10 FL_SCK N9 EEDO N10 FL_CE# M9 FLSH_SO P9 EECS P7 FL_SI M11 Table 28. LED Signals Signal Pin Signal Pin LINK_UP# A12 LINK100# B11 ACTIVITY# C11 LINK1000# B12 Table 29. Other Signals Signal Pin Signal Pin Signal Pin SDP[0] N14 SDP[6] N13 CTRL15 P11 SDP[1] P13 SDP[7] M12 CTRL25 B13 Table 30. IEEE Test Signals Signal CLK_VIEW Pin M8 31 82540EP -- Networking Silicon Table 31. PHY Signals Signal Pin Signal Pin Signal Pin XTAL1 K14 MDI[0]+ C13 MDI[2]+ F13 XTAL2 J14 MDI[1]- E14 MDI[3]- H14 REF B14 MDI[1]+ E13 MDI[3]+ H13 MDI[0]- C14 MDI[2]- F14 Table 32. Test Interface Signals Signal Pin Signal Pin Signal Pin JTAG_TCK L14 JTAG_TDO M14 JTAG_RST# L13 JTAG_TDI M13 JTAG_TMS L12 TEST A13 Table 33. Digital Power Signals Signal Pin Signal Pin Signal Pin DVDD (1.5V) E11 DVDD (1.5V) J8 DVDD (1.5V) L9 DVDD (1.5V) E12 DVDD (1.5V) J9 DVDD (1.5V) L10 DVDD (1.5V) G5 DVDD (1.5V) J10 VDDO (3.3V) A3 DVDD (1.5V) G6 DVDD (1.5V) J11 VDDO (3.3V) A7 DVDD (1.5V) G13 DVDD (1.5V) K5 VDDO (3.3V) A11 DVDD (1.5V) H5 DVDD (1.5V) K6 VDDO (3.3V) E1 DVDD (1.5V) H6 DVDD (1.5V) K7 VDDO (3.3V) K3 DVDD (1.5V) H7 DVDD (1.5V) K8 VDDO (3.3V) K4 DVDD (1.5V) H8 DVDD (1.5V) K9 VDDO (3.3V) K13 DVDD (1.5V) H11 DVDD (1.5V) K10 VDDO (3.3V) N6 DVDD (1.5V) J5 DVDD (1.5V) K11 VDDO (3.3V) N8 DVDD (1.5V) J6 DVDD (1.5V) L4 VDDO (3.3V) P2 DVDD (1.5V) J7 DVDD (1.5V) L5 VDDO (3.3V) P12 Table 34. Analog Power Signals Signal 32 Pin AVDDL (2.5 V) D9 AVDDL (2.5 V) D11 Signal AVDDL (2.5 V) Pin G12 Signal AVDDL (2.5 V) Pin L8 Networking Silicon -- 82540EP Table 35. Grounds and No Connect Signals Signal Pin Signal Pin Signal Pin Signal Pin VSS B3 VSS E7 VSS G9 NC A1 VSS B7 VSS E8 VSS G10 NC A14 VSS C10 VSS E9 VSS G11 NC C5 VSS C12 VSS E10 VSS G14 NC D10 VSS D4 VSS F4 VSS H9 NC D12 VSS D5 VSS F5 VSS H10 NC D14 VSS D6 VSS F6 VSS K2 NC F12 VSS D7 VSS F7 VSS K12 NC H12 VSS D8 VSS F8 VSS L6 NC J4 VSS D13 VSS F9 VSS L11 NC J13 VSS E2 VSS F10 VSS M6 NC L7 VSS E4 VSS F11 VSS N1 NC N11 VSS E5 VSS G7 VSS N12 NC P1 VSS E6 VSS G8 VSS P8 NC P14 Table 36. Signal Names in Pin Order (Sheet 1 of 6) Signal Name Pin NC A1 SERR# A2 3.3V A3 IDSEL A4 AD[25] A5 PME# A6 3.3V A7 AD[30] A8 LAN_PWR_GOOD A9 SMBCLK A10 3.3V A11 LINK_UP# A12 TEST A13 NC A14 AD[22] B1 AD[23] B2 VSS B3 AD[24] B4 33 82540EP -- Networking Silicon Table 36. Signal Names in Pin Order (Sheet 2 of 6) (Continued) Signal Name 34 Pin AD[26] B5 AD[27] B6 VSS B7 AD[31] B8 RST# B9 SMB_ALERT# B10 LINK100# B11 LINK1000# B12 CTRL25 B13 PHY REF B14 AD[21] C1 M66EN C2 REQ# C3 C/BE#[3] C4 NC C5 AD[28] C6 AD[29] C7 CLK_RUN# C8 SMBDATA C9 VSS C10 ACTIVITY# C11 VSS C12 MDI[0]+ C13 MDI[0]- C14 AD[18] D1 AD[19] D2 AD[20] D3 ALT_CLK125 (connect to VSS) D4 VSS D5 VSS D6 VSS D7 VSS D8 2.5 V D9 NC D10 2.5 V D11 NC D12 VSS D13 NC D14 Networking Silicon -- 82540EP Table 36. Signal Names in Pin Order (Sheet 3 of 6) (Continued) Signal Name Pin 3.3V E1 VSS E2 AD[17] E3 VSS E4 VSS E5 VSS E6 VSS E7 VSS E8 VSS E9 VSS E10 1.5V E11 1.5V E12 MDI[1]+ E13 MDI[1]- E14 IRDY# F1 FRAME# F2 C/BE#[2] F3 VSS F4 VSS F5 VSS F6 VSS F7 VSS F8 VSS F9 VSS F10 VSS F11 PHY_TSTPT (do not connect) F12 MDI[2]+ F13 MDI[2]- F14 CLK G1 VIO G2 TRDY# G3 ZP_COMP G4 1.5V G5 1.5V G6 VSS G7 VSS G8 VSS G9 VSS G10 35 82540EP -- Networking Silicon Table 36. Signal Names in Pin Order (Sheet 4 of 6) (Continued) Signal Name 36 Pin VSS G11 2.5 V G12 1.5V G13 VSS G14 STOP# H1 INTA# H2 DEVSEL# H3 ZN_COMP H4 1.5V H5 1.5V H6 1.5V H7 1.5V H8 VSS H9 VSS H10 1.5V H11 HSDACN (do not connect) H12 MDI3]+ H13 MDI[3]- H14 PAR J1 PERR# J2 GNT# J3 NC J4 1.5V J5 1.5V J6 1.5V J7 1.5V J8 1.5V J9 1.5V J10 1.5V J11 AUX_PWR J12 HSDACP (do not connect) J13 XTAL2 J14 AD[16] K1 VSS K2 3.3V K3 3.3V K4 1.5V K5 1.5V K6 Networking Silicon -- 82540EP Table 36. Signal Names in Pin Order (Sheet 5 of 6) (Continued) Signal Name Pin 1.5V K7 1.5V K8 1.5V K9 1.5V K10 1.5V K11 AVSS K12 3.3V K13 XTAL1 K14 AD[14] L1 AD[15] L2 C/BE#[1] L3 1.5V L4 1.5V L5 VSS L6 CLK_BYP# (do not connect) L7 2.5 V L8 1.5V L9 1.5V L10 VSS L11 JTAG_TMS L12 JTAG_RST# L13 JTAG_TCK L14 AD[11] M1 AD[12] M2 AD[13] M3 C/BE#[0] M4 AD[5] M5 VSS M6 AD[1] M7 CLK_VIEW M8 FL_CE# M9 EESK M10 FL_SI M11 SDP[7] M12 JTAG_TDI M13 JTAG_TDO M14 VSS N1 AD[10] N2 37 82540EP -- Networking Silicon Table 36. Signal Names in Pin Order (Sheet 6 of 6) (Continued) Signal Name 38 Pin AD[9] N3 AD[7] N4 AD[4] N5 3.3V N6 AD[0] N7 3.3V N8 FL_SCK N9 EEDO N10 NC N11 VSS N12 SDP[6] N13 SDP[0] N14 NC P1 3.3V P2 AD[8] P3 AD[6] P4 AD[3] P5 AD[2] P6 EECS P7 GND P8 FLSH_SO P9 EEDI P10 CTRL15 P11 3.3V P12 SDP[1] P13 NC P14 Networking Silicon -- 82540EP 5.5 Visual Pin Reference A B 1 NC AD[22] 2 SERR# AD[23] 3 3.3V VSS 4 IDSEL 5 C D E AD[21] AD[18] 3.3V M66EN AD[19] REQ# AD[24] C/BE#[3] AD[25] AD[26] NC 6 PME# AD[27] 7 3.3V 8 AD[30] P J IRDY# CLK STOP# PAR VSS FRAME# VIO INTA# PERR# AD[20] AD[17] C/BE#[2] TRDY# DVSEL# GNT# ALT_ CLK125 VSS VSS ZP_COMP ZN_COMP NC VSS VSS VSS 1.5V AD[28] VSS VSS VSS 1.5V 1.5V 1.5V VSS AD[29] VSS VSS VSS VSS 1.5V 1.5V 1.5V CLK_BYP# AD[31] CLK_ RUN# VSS VSS VSS VSS 1.5V 1.5V 1.5V 2.5V RST# SMBDATA 2.5V VSS VSS VSS VSS 1.5V 1.5V 1.5V FLSH_CE# SMB_ ALERT# VSS NC VSS VSS VSS VSS 1.5V 1.5V 1.5V EESK EEDO VSS VSS 1.5V 1.5V VSS FLSH_SI NC LAN_PWR_ GOOD 10 SMBCLK 11 3.3V LINK100# ACTIVITY# 2.5V 1.5V 12 LINK_UP# LINK1000# VSS NC 1.5V 13 TEST CTRL25 14 NC PHY REF MDI[0]+ MDI[0]- 1.5V 1.5V L N H 1.5V K M G 9 F AD[16] AD[14] AD[11] VSS NC VSS AD[15] AD[12] AD[10] 3.3V 3.3V C/B3#[1] AD[13] AD[9] AD[8] 3.3V 1.5V C/BE#[0] AD[7] AD[6] 1.5V AD[5] AD[4] AD[3] VSS VSS 3.3V AD[2] AD[1] AD[0] EECS 3.3V VSS 1.5V 1.5V VSS CLK_VIEW SDP[7] PHY_TSTPT 2.5V HSDACN 1.5V MDI[3]+ HSDACP 3.3V JTAG_TRST# JTAG_TDI MDI[3]+ XTAL2 XTAL1 JTAG_TCK JTAG_TDO VSS MDI[1]+ MDI[2]+ NC MDI[1]+ MDI[2]+ VSS AUX_PWR JTAG_TMS FLSH_SCK VSS SDP[6] SDP[0] FLSH_SO EEDI CTRL15 3.3V SDP[1] NC Figure 12. Ball Grid Array / Pin Reference for 196-TFBGA (Bottom/Pin View) Note: Figure 12 is rotated 90 degrees counter-clockwise from the pin 1 position (corner) in Figure 11. 39 82540EP -- Networking Silicon Note: 40 This page is intentionally left blank.