ATF1504AS-10AU44 - Atmel Corporation

Features

•High-density, High-performance, Electrically-erasable Complex Programmable

Logic Device

– 64 Macrocells

– 5 Product Terms per Macrocell, Expandable up to 40 per Macrocell

– 44, 68, 84, 100 Pins

– 7.5 ns Maximum Pin-to-pin Delay

– Registered Operation up to 125 MHz

– Enhanced Routing Resources

•In-System Programmability (ISP) via JTAG

•Flexible Logic Macrocell

– D/T/Latch Configurable Flip-flops

– Global and Individual Register Control Signals

– Global and Individual Output Enable

– Programmable Output Slew Rate

– Programmable Output Open Collector Option

– Maximum Logic Utilization by Burying a Register with a COM Output

•Advanced Power Management Features

– Automatic µA Standby for “L” Version

– Pin-controlled 1 mA Standby Mode

– Programmable Pin-keeper Circuits on Inputs and I/Os

– Reduced-power Feature per Macrocell

•Available in Commercial and Industrial Temperature Ranges

•Available in 44-, 68-, and 84-lead PLCC; 44- and 100-lead TQFP; and 100-lead PQFP

•Advanced EE Technology

– 100% Tested

– Completely Reprogrammable

– 10,000 Program/Erase Cycles

– 20-year Data Retention

– 2000V ESD Protection

– 200 mA Latch-up Immunity

•JTAG Boundary-scan Testing to IEEE Std. 1149.1-1990 and 1149.1a-1993 Supported

•PCI-compliant

•3.3V or 5.0V I/O Pins

•Security Fuse Feature

•Green (Pb/Halide-fee/RoHS Compliant) Package Options

Enhanced Features

•Improved Connectivity (Additional Feedback Routing, Alternate Input Routing)

•Output Enable Product Terms

•Transparent – Latch Mode

•Combinatorial Output with Registered Feedback within Any Macrocell

•Three Global Clock Pins

•ITD (Input Transition Detection) Circuits on Global Clocks, Inputs and I/O

•Fast Registered Input from Product Term

•Programmable “Pin-keeper” Option

•VCC Power-up Reset Option

•Pull-up Option on JTAG Pins TMS and TDI

•Advanced Power Management Features

– Edge-controlled Power-down “L”

– Individual Macrocell Power Option

– Disable ITD on Global Clocks, Inputs and I/O

High-

performance

Complex

Programmable

Logic Device

ATF1504AS

ATF1504ASL

Rev. 0950O–PLD–7/05

2ATF1504AS(L)

0950O–PLD–7/05

44-lead TQFP

Top View

I/O/TDI

I/O

GND

PD1/I/O

I/O

TMS/I/O

I/O

VCC

I/O

I/O/TDO

I/O

VCC

I/O

I/O/TCK

I/O

GND

I/O

GND

VCC

I/O

PD2/I/O

I/O

VCC

GCLK2/OE2/I

GCLR/I

I/OE1

GCLK1/I

GND

GCLK3/I/O

I/O

44-lead PLCC

Top View

TDI/I/O

I/O

GND

PD1/I/O

I/O

I/O/TMS

I/O

VCC

I/O

I/O/TDO

I/O

VCC

I/O

I/O/TCK

I/O

GND

I/O

GND

VCC

I/O

PD2/I/O

I/O

VCC

GCLK2/OE2/I

GCLR/I

OE1/I

GCLK1/I

GND

GCLK3/I/O

I/O

68-lead PLCC

Top View

I/O

VCCIO

I/O/TD1

I/O

GND

I/O/PD1

I/O

I/O/TMS

I/O

VCCIO

I/O

GND

I/O

GND

I/O/TDO

I/O

VCCIO

I/O

I/O/TCK

I/O

GND

I/O

VCCIO

I/O

GND

VCCINT

I/O

I/O/PD2

GND

I/O

VCCIO

I/O

GND

I/O

VCCINT

GCLK2/OE2/I

GCLR/I

OE1/I

GCLK1/I

GND

GCLK3/I/O

I/O

VCCIO

I/O

84-lead PLCC

Top View

I/O

VCCIO

I/O/TDI

I/O

GND

I/O/PD1

I/O

I/O/TMS

I/O

VCCIO

I/O

GND

I/O

GND

I/O/TDO

I/O

VCCIO

I/O

I/O/TCK

I/O

GND

I/O

VCCIO

I/O

GND

VCCINT

I/O

I/O/PD2

GND

I/O

VCCIO

I/O

GND

I/O

VCCINT

GCLK2/OE2/I

I/GCLR

I/OE1

GCLK1/I

GND

GCLK3/I/O

I/O

VCCIO

1/O

I/O

ATF1504AS(L)

0950O–PLD–7/05

100-lead PQFP

Top View

I/O

VCCIO

I/O/TDI

I/O

GND

I/O/PD1

I/O

I/O/TMS

I/O

VCCIO

I/O

GND

I/O

GND

I/O/TDO

I/O

VCCIO

I/O

I/O/TCK

I/O

GND

I/O

VCCIO

100

I/O

VCCIO

I/O

GND

VCCINT

I/O

I/O/PD2

GND

I/O

GND

I/O

VCCINT

INPUT/OE2/GCLK2

INPUT/GCLR

INPUT/OE1

INPUT/GCLK1

GND

I/O/GCLK3

I/O

VCCIO

I/O

100-lead TQFP

Top View

VCCIO

I/O/TDI

I/O

GND

I/O/PD1

I/O

I/O/TMS

I/O

VCCIO

I/O

GND

I/O/TDO

I/O

VCCIO

I/O

I/O/TCK

I/O

GND

I/O

VCCIO

GND

I/O

VCCIO

I/O

GND

VCCINT

I/O

I/O/PD2

GND

I/O

GND

I/O

VCCINT

INPUT/OE2/GCLK2

INPUT/GCLR

INPUT/OE1

INPUT/GCLK1

GND

I/O/GCLK3

I/O

VCCIO

I/O

100

4ATF1504AS(L)

0950O–PLD–7/05

Description The ATF1504AS is a high-performance, high-density complex programmable logic

device (CPLD) that utilizes Atmel’s proven electrically-erasable memory technology.

With 64 logic macrocells and up to 68 inputs, it easily integrates logic from several TTL,

SSI, MSI, LSI and classic PLDs. The ATF1504AS’s enhanced routing switch matrices

increase usable gate count and the odds of successful pin-locked design modifications.

The ATF1504AS has up to 68 bi-directional I/O pins and four dedicated input pins,

depending on the type of device package selected. Each dedicated pin can also serve

as a global control signal, register clock, register reset or output enable. Each of these

control signals can be selected for use individually within each macrocell.

Each of the 64 macrocells generates a buried feedback that goes to the global bus.

Each input and I/O pin also feeds into the global bus. The switch matrix in each logic

block then selects 40 individual signals from the global bus. Each macrocell also gener-

ates a foldback logic term that goes to a regional bus. Cascade logic between

macrocells in the ATF1504AS allows fast, efficient generation of complex logic func-

tions. The ATF1504AS contains four such logic chains, each capable of creating sum

term logic with a fan-in of up to 40 product terms.

The ATF1504AS macrocell, shown in Figure 1, is flexible enough to support highly-com-

plex logic functions operating at high speed. The macrocell consists of five sections:

product terms and product term select multiplexer, OR/XOR/CASCADE logic, a flip-flop,

output select and enable, and logic array inputs.

ATF1504AS(L)

0950O–PLD–7/05

Block Diagram

Unused product terms are automatically disabled by the compiler to decrease power

consumption. A security fuse, when programmed, protects the contents of the

ATF1504AS. Two bytes (16 bits) of User Signature are accessible to the user for pur-

poses such as storing project name, part number, revision or date. The User Signature

is accessible regardless of the state of the security fuse.

The ATF1504AS device is an in-system programmable (ISP) device. It uses the indus-

try-standard 4-pin JTAG interface (IEEE Std. 1149.1), and is fully-compliant with JTAG’s

Boundary-scan Description Language (BSDL). ISP allows the device to be programmed

without removing it from the printed circuit board. In addition to simplifying the manufac-

turing flow, ISP also allows design modifications to be made in the field via software.

I/O (MC64)/GCLK3

6ATF1504AS(L)

0950O–PLD–7/05

Product Terms and Select

Mux

Each ATF1504AS macrocell has five product terms. Each product term receives as its

possible inputs all signals from both the global bus and regional bus.

The product term select multiplexer (PTMUX) allocates the five product terms as

needed to the macrocell logic gates and control signals. The PTMUX programming is

determined by the design compiler, which selects the optimum macrocell configuration.

OR/XOR/CASCADE Logic The ATF1504AS’s logic structure is designed to efficiently support all types of logic.

Within a single macrocell, all the product terms can be routed to the OR gate, creating a

5-input AND/OR sum term. With the addition of the CASIN from neighboring macrocells,

this can be expanded to as many as 40 product terms with a little small additional delay.

The macrocell’s XOR gate allows efficient implementation of compare and arithmetic

functions. One input to the XOR comes from the OR sum term. The other XOR input can

be a product term or a fixed high- or low-level. For combinatorial outputs, the fixed level

input allows polarity selection. For registered functions, the fixed levels allow DeMorgan

minimization of product terms. The XOR gate is also used to emulate T- and JK-type

flip-flops.

Flip-flop The ATF1504AS’s flip-flop has very flexible data and control functions. The data input

can come from either the XOR gate, from a separate product term or directly from the

I/O pin. Selecting the separate product term allows creation of a buried registered feed-

back within a combinatorial output macrocell. (This feature is automatically implemented

by the fitter software). In addition to D, T, JK and SR operation, the flip-flop can also be

configured as a flow-through latch. In this mode, data passes through when the clock is

high and is latched when the clock is low.

The clock itself can be either one of the Global CLK Signals (GCK[0 : 2]) or an individual

product term. The flip-flop changes state on the clock’s rising edge. When the GCK sig-

nal is used as the clock, one of the macrocell product terms can be selected as a clock

enable. When the clock enable function is active and the enable signal (product term) is

low, all clock edges are ignored. The flip-flop’s asynchronous reset signal (AR) can be

either the Global Clear (GCLEAR), a product term, or always off. AR can also be a logic

OR of GCLEAR with a product term. The asynchronous preset (AP) can be a product

term or always off.

Output Select and Enable The ATF1504AS macrocell output can be selected as registered or combinatorial. The

buried feedback signal can be either combinatorial or registered signal regardless of

whether the output is combinatorial or registered.

The output enable multiplexer (MOE) controls the output enable signals. Any buffer can

be permanently enabled for simple output operation. Buffers can also be permanently

disabled to allow use of the pin as an input. In this configuration all the macrocell

resources are still available, including the buried feedback, expander and CASCADE

logic. The output enable for each macrocell can be selected as either of the two dedi-

cated OE input pins as an I/O pin configured as an input, or as an individual product

term.

Global Bus/Switch Matrix The global bus contains all input and I/O pin signals as well as the buried feedback sig-

nal from all 64 macrocells. The switch matrix in each logic block receives as its possible

inputs all signals from the global bus. Under software control, up to 40 of these signals

can be selected as inputs to the logic block.

ATF1504AS(L)

0950O–PLD–7/05

Foldback Bus Each macrocell also generates a foldback product term. This signal goes to the regional

bus and is available to four macrocells. The foldback is an inverse polarity of one of the

macrocell’s product terms. The sixteen foldback terms in each region allow generation

of high fan-in sum terms (up to sixteen product terms) with a nominal additional delay.

Figure 1. ATF1504AS Macrocell

8ATF1504AS(L)

0950O–PLD–7/05

Programmable Pin-

keeper Option for

Inputs and I/Os

The ATF1504AS offers the option of programming all input and I/O pins so that pin-

keeper circuits can be utilized. When any pin is driven high or low and then subse-

quently left floating, it will stay at that previous high- or low-level. This circuitry prevents

unused input and I/O lines from floating to intermediate voltage levels, which causes

unnecessary power consumption and system noise. The keeper circuits eliminate the

need for external pull-up resistors and eliminate their DC power consumption.

Input Diagram

Speed/Power

Management

The ATF1504AS has several built-in speed and power management features. The

ATF1504AS contains circuitry that automatically puts the device into a low-power

standby mode when no logic transitions are occurring. This not only reduces power con-

sumption during inactive periods, but also provides proportional power savings for most

applications running at system speeds below 5 MHz. This feature may be selected as a

device option.

I/O Diagram

To further reduce power, each ATF1504AS macrocell has a Reduced Power bit feature.

This feature allows individual macrocells to be configured for maximum power savings.

This feature may be selected as a design option.

All ATF1504AS also have an optional power-down mode. In this mode, current drops to

below 10 mA. When the power-down option is selected, either PD1 or PD2 pins (or

both) can be used to power-down the part. The power-down option is selected in the

design source file. When enabled, the device goes into power-down when either PD1 or

PD2 is high. In the power-down mode, all internal logic signals are latched and held, as

are any enabled outputs.

ATF1504AS(L)

0950O–PLD–7/05

All pin transitions are ignored until the PD pin is brought low. When the power-down fea-

ture is enabled, the PD1 or PD2 pin cannot be used as a logic input or output. However,

the pin’s macrocell may still be used to generate buried foldback and cascade logic

signals.

All power-down AC characteristic parameters are computed from external input or I/O

pins, with Reduced Power Bit turned on. For macrocells in reduced-power mode

(reduced-power bit turned on), the reduced-power adder, tRPA, must be added to the

AC parameters, which include the data paths tLAD, tLAC, tIC, tACL, tACH and tSEXP.

The ATF1504AS macrocell also has an option whereby the power can be reduced on a

per macrocell basis. By enabling this power-down option, macrocells that are not used

in an application can be turned-down, thereby reducing the overall power consumption

of the device.

Each output also has individual slew rate control. This may be used to reduce system

noise by slowing down outputs that do not need to operate at maximum speed. Outputs

default to slow switching, and may be specified as fast switching in the design file.

Design Software

Support

ATF1504AS designs are supported by several industry-standard third-party tools. Auto-

mated fitters allow logic synthesis using a variety of high level description languages

and formats.

Power-up Reset The ATF1504AS is designed with a power-up reset, a feature critical for state machine

initialization. At a point delayed slightly from VCC crossing VRST, all registers will be ini-

tialized, and the state of each output will depend on the polarity of its buffer. However,

due to the asynchronous nature of reset and uncertainty of how VCC actually rises in the

system, the following conditions are required:

1. The VCC rise must be monotonic,

2. After reset occurs, all input and feedback setup times must be met before driving

the clock pin high, and,

3. The clock must remain stable during TD.

The ATF1504AS has two options for the hysteresis about the reset level, VRST, Small

and Large. During the fitting process users may configure the device with the Power-up

Reset hysteresis set to Large or Small. Atmel POF2JED users may select the Large

option by including the flag “-power_reset” on the command line after “filename.POF”.

To allow the registers to be properly reinitialized with the Large hysteresis option

selected, the following condition is added:

4. If VCC falls below 2.0V, it must shut off completely before the device is turned on

again.

When the Large hysteresis option is active, ICC is reduced by several hundred micro-

amps as well.

Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF1504AS fuse pat-

terns. Once programmed, fuse verify is inhibited. However, the 16-bit User Signature

remains accessible.

10 ATF1504AS(L)

0950O–PLD–7/05

Programming ATF1504AS devices are in-system programmable (ISP) devices utilizing the 4-pin JTAG

protocol. This capability eliminates package handling normally required for programming

and facilitates rapid design iterations and field changes.

Atmel provides ISP hardware and software to allow programming of the ATF1504AS via

the PC. ISP is performed by using either a download cable or a comparable board tester

or a simple microprocessor interface.

To facilitate ISP programming by the Automated Test Equipment (ATE) vendors. Serial

Vector Format (SVF) files can be created by Atmel provided software utilities.

ATF1504AS devices can also be programmed using standard third-party programmers.

With third-party programmer, the JTAG ISP port can be disabled thereby allowing

four additional I/O pins to be used for logic.

Contact your local Atmel representatives or Atmel PLD applications for details.

ISP Programming

Protection

The ATF1504AS has a special feature that locks the device and prevents the inputs and

I/O from driving if the programming process is interrupted for any reason. The inputs

and I/O default to high-Z state during such a condition. In addition the pin-keeper option

preserves the former state during device programming, if this circuit were previously

programmed on the device. This prevents disturbing the operation of other circuits in the

system while the ATF1504AS is being programmed via ISP.

All ATF1504AS devices are initially shipped in the erased state thereby making them

ready to use for ISP.

Note: For more information refer to the “Designing for In-System Programmability with Atmel

CPLDs” application note.

ATF1504AS(L)

0950O–PLD–7/05

Notes: 1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec.

2. When macrocell reduced-power feature is enabled.

Note: Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.

The OGI pin (high-voltage pin during programming) has a maximum capacitance of 12 pF.

DC and AC Operating Conditions

Commercial Industrial

Operating Temperature (Ambient) 0°C - 70°C-40°C - 85°C

VCCINT or VCCIO (5V) Power Supply 5V ± 5% 5V ± 10%

VCCIO (3.3V) Power Supply 3.0V - 3.6V 3.0V - 3.6V

DC Characteristics

Symbol Parameter Condition Min Typ Max Units

IIL Input or I/O Low

Leakage Current VIN = VCC -2 -10 µA

IIH Input or I/O High

Leakage Current 210

IOZ Tri-state Output

Off-state Current VO = VCC or GND -40 40 µA

ICC1 Power Supply Current,

Standby

VCC = Max

VIN = 0, VCC

Std Mode Com. 105 mA

Ind. 130 mA

“L” Mode Com. 10 µA

Ind. 10 µA

ICC2 Power Supply Current,

Power-down Mode

VCC = Max

VIN = 0, VCC “PD” Mode 1 10 mA

ICC3(2) Current in Reduced-power

Mode

VCC = Max

VIN = 0, VCC Std Power Com 85 ma

Ind 105

VCCIO Supply Voltage 5.0V Device Output Com. 4.75 5.25 V

Ind. 4.5 5.5 V

VCCIO Supply Voltage 3.3V Device Output 3.0 3.6 V

VIL Input Low Voltage -0.3 0.8 V

VIH Input High Voltage 2.0 VCCIO + 0.3 V

VOL

Output Low Voltage (TTL) VIN = VIH or VIL

VCCIO = MIN, IOL = 12 mA

Com. 0.45 V

Ind.

Output Low Voltage (CMOS) VIN = VIH or VIL

VCC = MIN, IOL = 0.1 mA

Com. .2 V

Ind. .2 V

VOH Output High Voltage (TTL) VIN = VIH or VIL

VCCIO = MIN, IOH = -4.0 mA 2.4 V

Pin Capacitance

Typ Max Units Conditions

CIN 810 pF V

IN = 0V; f = 1.0 MHz

CI/O 810 pF V

OUT = 0V; f = 1.0 MHz

12 ATF1504AS(L)

0950O–PLD–7/05

Absolute Maximum Ratings*

Temperature Under Bias.................................. -40°C to +85°C *NOTICE: Stresses beyond those listed under “Absolute

Maximum Ratings” may cause permanent dam-

age to the device. This is a stress rating only and

functional operation of the device at these or any

other conditions beyond those indicated in the

operational sections of this specification is not

implied. Exposure to absolute maximum rating

conditions for extended periods may affect device

reliability.

Note: 1. Minimum voltage is -0.6V DC, which may under-

shoot to -2.0V for pulses of less than 20 ns. Max-

imum output pin voltage is VCC + 0.75V DC,

which may overshoot to 7.0V for pulses of less

than 20 ns.

Storage Temperature..................................... -65°C to +150°C

Voltage on Any Pin with

Respect to Ground .........................................-2.0V to +7.0V(1)

Voltage on Input Pins

with Respect to Ground

During Programming.....................................-2.0V to +14.0V(1)

Programming Voltage with

Respect to Ground .......................................-2.0V to +14.0V(1)

AC Characteristics

Symbol Parameter

-7 -10 -15 -20 -25

UnitsMin Max Min Max Min Max Min Max Min Max

tPD1 Input or Feedback to

Non-registered Output 7.5 10 3 15 20 25 ns

tPD2 I/O Input or Feedback to

Non-registered Feedback 793121625ns

tSU Global Clock Setup Time 6 7 11 16 20 ns

tHGlobal Clock Hold Time 0 0 0 0 0 ns

tFSU Global Clock Setup Time of

Fast Input 33335ns

tFH Global Clock Hold Time of

Fast Input 0.5 0.5 1.0 1.5 2 ns

tCOP Global Clock to Output Delay 4.5 5 8 10 13 ns

tCH Global Clock High Time 3 4 5 6 7 ns

tCL Global Clock Low Time 3 4 5 6 7 ns

tASU Array Clock Setup Time 3 3 4 4 5 ns

tAH Array Clock Hold Time 2 3 4 5 6 ns

tACOP Array Clock Output Delay 7.5 10 15 20 25 ns

tACH Array Clock High Time 3 4 6 8 10 ns

tACL Array Clock Low Time 3 4 6 8 10 ns

tCNT Minimum Clock Global Period 8 10 13 17 22 ns

fCNT Maximum Internal Global

Clock Frequency 125 100 76.9 66 50 MHz

tACNT Minimum Array Clock Period 8 10 13 17 22 ns

fACNT Maximum Internal Array

Clock Frequency 125 100 76.9 66 50 MHz

ATF1504AS(L)

0950O–PLD–7/05

Note: See ordering information for valid part numbers.

Timing Model

AC Characteristics (Continued)

Symbol Parameter

-7 -10 -15 -20 -25

UnitsMin Max Min Max Min Max Min Max Min Max

fMAX Maximum Clock Frequency 166.7 125 100 83.3 60 MHz

tIN Input Pad and Buffer Delay 0.5 0.5 2 2 2 ns

tIO I/O Input Pad and Buffer Delay 0.5 0.5 2 2 2 ns

tFIN Fast Input Delay 112 22ns

tSEXP Foldback Term Delay 4 5 8 10 12 ns

tPEXP Cascade Logic Delay 0.8 0.8 1 1 1.2 ns

tLAD Logic Array Delay 356 78ns

tLAC Logic Control Delay 356 78ns

tIOE Internal Output Enable Delay 2 2 3 3 4 ns

tOD1

Output Buffer and Pad Delay

(Slow slew rate = OFF;

VCCIO = 5V; CL = 35 pF)

21.54 5 6ns

tOD2

Output Buffer and Pad Delay

(Slow slew rate = OFF;

VCCIO = 3.3V; CL = 35 pF)

2.5 2.0 5 6 7 ns

tOD3

Output Buffer and Pad Delay

(Slow slew rate = ON;

VCCIO = 5V or 3.3V; CL = 35 pF)

55.58 1010ns

14 ATF1504AS(L)

0950O–PLD–7/05

Notes: 1. See ordering information for valid part numbers.

2. The tRPA parameter must be added to the tLAD, tLAC,tTIC, tACL, and tSEXP parameters for macrocells running in the reduced-

power mode.

Input Test Waveforms and Measurement Levels

tR, tF = 1.5 ns typical

AC Characteristics (Continued)

Symbol Parameter

-7 -10 -15 -20 -25

UnitsMin Max Min Max Min Max Min Max Min Max

tZX1

Output Buffer Enable Delay

(Slow slew rate = OFF;

VCCIO = 5.0V; CL = 35 pF)

4.0 5.0 7 9 10 ns

tZX2

Output Buffer Enable Delay

(Slow slew rate = OFF;

VCCIO = 3.3V; CL = 35 pF)

4.5 5.5 7 9 10 ns

tZX3

Output Buffer Enable Delay

(Slow slew rate = ON;

VCCIO = 5.0V/3.3V; CL = 35 pF)

9 9 10 11 12 ns

tXZ Output Buffer Disable Delay

(CL = 5 pF) 45678ns

tSU Register Setup Time 3 3 4 5 6 ns

tHRegister Hold Time 2 3 4 5 6 ns

tFSU Register Setup Time of Fast Input 3 3 2 2 3 ns

tFH Register Hold Time of Fast Input 0.5 0.5 2 2 2.5 ns

tRD Register Delay 1 2 1 2 2 ns

tCOMB Combinatorial Delay 1 2 1 2 2 ns

tIC Array Clock Delay 3 5 6 7 8 ns

tEN Register Enable Time 3 5 6 7 8 ns

tGLOB Global Control Delay 1 1 1 1 1 ns

tPRE Register Preset Time 2 3 4 5 6 ns

tCLR Register Clear Time 2 3 4 5 6 ns

tUIM Switch Matrix Delay 1 1 2 2 2 ns

tRPA Reduced-power Adder(2) 10 11 13 14 15 ns

ATF1504AS(L)

0950O–PLD–7/05

Output AC Test Loads

Note: *Numbers in parenthesis refer to 3.0V operating conditions (preliminary).

Power-down Mode The ATF1504AS includes an optional pin-controlled power-down feature. When this

mode is enabled, the PD pin acts as the power-down pin. When the PD pin is high, the

device supply current is reduced to less than 10 mA. During power-down, all output data

and internal logic states are latched internally and held. Therefore, all registered and

combinatorial output data remain valid. Any outputs that were in a high-Z state at the

onset will remain at high-Z. During power-down, all input signals except the power-down

pin are blocked. Input and I/O hold latches remain active to ensure that pins do not float

to indeterminate levels, further reducing system power. The power-down mode feature

is enabled in the logic design file or as a fitted or translated s/w option. Designs using

the power-down pin may not use the PD pin as a logic array input. However, all other PD

pin macrocell resources may still be used, including the buried feedback and foldback

product term array inputs.

Notes: 1. For slow slew outputs, add tSSO.

2. Pin or product term.

3. Includes tRPA due to reduced power bit enabled.

Power Down AC Characteristics(1)(2)

Symbol Parameter

-7 -10 -15 -20 -25

UnitsMin Max Min Max Min Max Min Max Min Max

tIVDH Valid I, I/O before PD High 7 10 15 20 25 ns

tGVDH Valid OE(2) before PD High 7 10 15 20 25 ns

tCVDH Valid Clock(2) before PD High 7 10 15 20 25 ns

tDHIX I, I/O Don’t Care after PD High 12 15 25 30 35 ns

tDHGX OE(2) Don’t Care after PD High 12 15 25 30 35 ns

tDHCX Clock(2) Don’t Care after PD High 12 15 25 30 35 ns

tDLIV PD Low to Valid I, I/O 11111µs

tDLGV PD Low to Valid OE (Pin or Term) 11111µs

tDLCV PD Low to Valid Clock (Pin or Term)11111µs

tDLOV PD Low to Valid Output 11111µs

16 ATF1504AS(L)

0950O–PLD–7/05

JTAG-BST/ISP

Overview

The JTAG boundary-scan testing is controlled by the Test Access Port (TAP) controller

in the ATF1504AS. The boundary-scan technique involves the inclusion of a shift-regis-

ter stage (contained in a boundary-scan cell) adjacent to each component so that

signals at component boundaries can be controlled and observed using scan testing

principles. Each input pin and I/O pin has its own boundary-scan cell (BSC) in order to

support boundary scan testing. The ATF1504AS does not currently include a Test Reset

(TRST) input pin because the TAP controller is automatically reset at power-up. The five

JTAG modes supported include: SAMPLE/PRELOAD, EXTEST, BYPASS, IDCODE

and HIGHZ. The ATF1504AS’s ISP can be fully described using JTAG’s BSDL as

described in IEEE Standard 1149.1b. This allows ATF1504AS programming to be

described and implemented using any one of the third-party development tools support-

ing this standard.

The ATF1504AS has the option of using four JTAG-standard I/O pins for boundary-scan

testing (BST) and in-system programming (ISP) purposes. The ATF1504AS is program-

mable through the four JTAG pins using the IEEE standard JTAG programming protocol

established by IEEE Standard 1149.1 using 5V TTL-level programming signals from the

ISP interface for in-system programming. The JTAG feature is a programmable option.

If JTAG (BST or ISP) is not needed, then the four JTAG control pins are available as I/O

pins.

JTAG Boundary-scan

Cell (BSC) Testing

The ATF1504AS contains up to 68 I/O pins and four input pins, depending on the device

type and package type selected. Each input pin and I/O pin has its own boundary-scan

cell (BSC) in order to support boundary-scan testing as described in detail by IEEE

Standard 1149.1. A typical BSC consists of three capture registers or scan registers and

up to two update registers. There are two types of BSCs, one for input or I/O pin, and

one for the macrocells. The BSCs in the device are chained together through the cap-

ture registers. Input to the capture register chain is fed in from the TDI pin while the

output is directed to the TDO pin. Capture registers are used to capture active device

data signals, to shift data in and out of the device and to load data into the update regis-

ters. Control signals are generated internally by the JTAG TAP controller. The BSC

configuration for the input and I/O pins and macrocells are shown below.

BSC Configuration for Input and I/O Pins (Except JTAG TAP Pins)

Note: The ATF1504AS has pull-up option on TMS and TDI pins. This feature is selected as a design option.

ATF1504AS(L)

0950O–PLD–7/05

BSC Configuration for Macrocell

1DQ

DQ DQ

Capture

Update

DQ DQ

TDI

OUTJ

OEJ

Shift

Clock

Mode

TDO

Pin BSC

Macrocell BSC

18 ATF1504AS(L)

0950O–PLD–7/05

PCI Compliance The ATF1504AS also supports the growing need in the industry to support the new

Peripheral Component Interconnect (PCI) interface standard in PCI-based designs and

specifications. The PCI interface calls for high current drivers, which are much larger

than the traditional TTL drivers. In general, PLDs and FPGAs parallel outputs to support

the high current load required by the PCI interface. The ATF1504AS allows this without

contributing to system noise while delivering low output-to-output skew. Having a pro-

grammable high drive option is also possible without increasing output delay or pin

capacitance. The PCI electrical characteristics appear on the next page.

PCI Voltage-to-current Curves for +5V Signaling in Pull-up Mode

PCI Voltage-to-current Curves for +5V Signaling in Pull-down Mode

2.4

VCC

1.4

-2 -44 -178

Current (mA)

AC drive

point

drive point

Voltage

Pull Up

Test Point

2.2

VCC

0.55

3,6 95 380

Current (mA)

AC drive

point

drive point

Voltage

Pull Down

Test Point

ATF1504AS(L)

0950O–PLD–7/05

Note: Leakage current is with pin-keeper off.

Notes: 1. Equation A: IOH = 11.9 (VOUT - 5.25) * (VOUT + 2.45) for VCC > VOUT > 3.1V.

2. Equation B: IOL = 78.5 * VOUT * (4.4 - VOUT) for 0V < VOUT < 0.71V.

PCI DC Characteristics

Symbol Parameter Conditions Min Max Units

VCC Supply Voltage 4.75 5.25 V

VIH Input High Voltage 2.0 VCC + 0.5 V

VIL Input Low Voltage -0.5 0.8 V

IIH Input High Leakage Current VIN = 2.7V 70 µA

IIL Input Low Leakage Current VIN = 0.5V -70 µA

VOH Output High Voltage IOUT = -2 mA 2.4 V

VOL Output Low Voltage IOUT = 3 mA, 6 mA 0.55 V

CIN Input Pin Capacitance 10 pF

CCLK CLK Pin Capacitance 12 pF

CIDSEL IDSEL Pin Capacitance 8pF

LPIN Pin Inductance 20 nH

PCI AC Characteristics

Symbol Parameter Conditions Min Max Units

IOH(AC)

Switching

Current High

(Test High)

0 < VOUT ≤ 1.4 -44 mA

1.4 < VOUT < 2.4 -44+(VOUT - 1.4)/0.024 mA

3.1 < VOUT < VCC Equation A mA

VOUT = 3.1V -142 µA

IOL(AC)

Switching

Current Low

(Test Point)

VOUT > 2.2V 95 mA

2.2 > VOUT > 0 VOUT/0.023 mA

0.1 > VOUT > 0 Equation B mA

VOUT = 0.71 206 mA

ICL Low Clamp Current -5 < VIN ≤-1 -25+(VIN + 1)/0.015 mA

SLEWROutput Rise Slew Rate 0.4V to 2.4V load 0.5 3 V/ns

SLEWFOutput Fall Slew Rate 2.4V to 0.4V load 0.5 3 V/ns

20 ATF1504AS(L)

0950O–PLD–7/05

OE (1, 2) Global OE Pins

GCLR Global Clear Pin

GCLK (1, 2, 3) Global Clock Pins

PD (1, 2) Power down pins

TDI, TMS, TCK, TDO JTAG pins used for boundary-scan testing or in-system programming

GND Ground Pins

VCCINT VCC pins for the device (+5V - Internal)

VCCIO VCC pins for output drivers (for I/O pins) (+5V or 3.3V - I/Os)

ATF1504AS Dedicated Pinouts

Dedicated Pin

44-lead

TQFP

44-lead

J-lead

68-lead

J-lead

84-lead

J-lead

100-lead

PQFP

100-lead

TQFP

INPUT/OE2/GCLK2 40 2 2 2 92 90

INPUT/GCLR 39 1 1 1 91 89

INPUT/OE1 384468849088

INPUT/GCLK1374367838987

I/O /GCLK3 354165818785

I/O/PD (1,2) 5, 19 11, 25 17, 37 20, 46 14, 44 12, 42

I/O/TDI (JTAG) 1 7 12 14 6 4

I/O/TMS (JTAG) 7 13 19 23 17 15

I/O/TCK (JTAG) 26 32 50 62 64 62

I/O/TDO (JTAG) 32 38 57 71 75 73

GND 4, 16, 24, 36 10, 22, 30, 42 6, 16, 26, 34,

38, 48, 58, 66

7, 19, 32, 42,

47, 59, 72, 82

13, 28, 40, 45,

61, 76, 88, 97

11, 26, 38, 43,

59, 74, 86, 95

VCCINT 9, 17, 29, 41 3, 15, 23, 35 3, 35 3, 43 41, 93 39, 91

VCCIO ––

11, 21, 31, 43,

53, 63

13, 26, 38, 53,

66, 78

5, 20, 36, 53,

68, 84

3, 18, 34, 51,

66, 82

N/C – – – –

1, 2, 7, 9,

24, 26, 29, 30,

51, 52, 55, 57,

72, 74, 79, 80

1, 2, 5, 7, 22,

24, 27, 28, 49,

50, 53, 55, 70,

72, 77, 78

# of Signal Pins 36 36 52 68 68 68

# User I/O Pins 32 32 48 64 64 64

ATF1504AS(L)

0950O–PLD–7/05

ATF1504AS I/O Pinouts

MC PLC

44-

lead

PLCC

44-

lead

TQFP

68-

lead

PLCC

84-

lead

PLCC

100-

lead

PQFP

100-

lead

TQFP MC PLC

44-

lead

PLCC

44-

lead

TQFP

68-

lead

PLCC

84-

lead

PLCC

100-

lead

PQFP

100-

lead

TQFP

1 A 12 6 18 22 16 14 33 C 24 18 36 44 42 40

2 A – – – 21 15 13 34 C – – – 45 43 41

3A/

PD1 11 5 17 20 14 12 35 C/

PD2 25 19 37 46 44 42

4 A 9 3 15 18 12 10 36 C 26 20 39 48 46 44

5 A 8 2 14 17 11 9 37 C 27 21 40 49 47 45

6 A – – 13 16 10 8 38 C – – 41 50 48 46

7 A – – – 15 8 6 39 C – – – 51 49 47

TDI A 7 1 12 14 6 4 40 C 28 22 42 52 50 48

9 A – – 10 12 4 100 41 C 29 23 44 54 54 52

10 A – – – 11 3 99 42 C – – – 55 56 54

11 A 6 44 9 10 100 98 43 C – – 45 56 58 56

12 A – – 8 9 99 97 44 C – – 46 57 59 57

13 A – – 7 8 98 96 45 C – – 47 58 60 58

14 A 5 43 5 6 96 94 46 C 31 25 49 60 62 60

15A–––5959347C –––616361

16 A 4 42 4 4 94 92 48/

TCK C 32265062 64 62

17 B 21 15 33 41 39 37 49 D 33 27 51 63 65 63

18 B – – – 40 38 36 50 D – – – 64 66 64

19 B 20 14 32 39 37 35 51 D 34 28 52 65 67 65

20 B 19 13 30 37 35 33 52 D 36 30 54 67 69 67

21 B 18 12 29 36 34 32 53 D 37 31 55 68 70 68

22 B – – 28 35 33 31 54 D – – 56 69 71 69

23 B – – – 34 32 30 55 D – – – 70 73 71

24B17112733 31 2956/

TDO D 38325771 75 73

25 B 16 10 25 31 27 25 57 D 39 33 59 73 77 75

26 B – – – 30 25 23 58 D – – – 74 78 76

27 B – – 24 29 23 21 59 D – – 60 75 81 79

28 B – – 23 28 22 20 60 D – – 61 76 82 80

29 B – – 22 27 21 19 61 D – – 62 77 83 81

30 B 14 8 20 25 19 17 62 D 40 34 64 79 85 83

31 B – – – 24 18 16 63 D – – – 80 86 84

32/

TMS B 13 7 19 23 17 15 64 D/

GCLK3 41 35 65 81 87 85

22 ATF1504AS(L)

0950O–PLD–7/05

SUPPLY CURRENT VS. SUPPLY VOLTAGE

(TA = 25°C, F = 0)

100

125

4.50 4.75 5.00 5.25 5.50

VCC (V)

ICC (mA)

STANDARD

REDUCED POWER MODE

SUPPLY CURRENT VS. SUPPLY VOLTAGE

LOW-POWER ("L") VERSION

(TA = 25°C, F = 0)

4.50 4.75 5.00 5.25 5.50

VCC (V)

ICC (µA)

SUPPLY CURRENT VS. FREQUENCY

STANDARD POWER (TA = 25°C)

0.0

50.0

100.0

150.0

200.0

0.00 20.00 40.00 60.00 80.00 100.00

FREQUENCY (MHz)

ICC (mA)

STANDARD POWER

REDUCED POWER MODE

OUTPUT SOURCE CURRENT VS. SUPPLY VOLTAGE

(VOH = 2.4V, TA= 25°C)

-60.0

-50.0

-40.0

-30.0

-20.0

-10.0

0.0

4.50 4.75 5.00 5.25 5.50

SUPPLY VOLTAGE (V)

IOH (mA)

SUPPLY CURRENT VS. SUPPLY VOLTAGE

PIN-CONTROLLED POWER-DOWN MODE

(TA = 25°C, F = 0)

700

800

900

1000

1100

4.50 4.75 5.00 5.25 5.50

VCC (V)

ICC (µA)

STANDARD POWER

REDUCED POWER MODE

SUPPLY CURRENT VS. FREQUENCY

LOW-POWER ("L") VERSION

LOW POWER (TA = 25°C)

0.0

25.0

50.0

75.0

100.0

125.0

0.00 5.00 10.00 15.00 20.00 25.00

FREQUENCY (MHz)

ICC (mA)

STANDARD POWER

REDUCED POWER MODE

OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE

(VCC = 5V, TA = 25°C)

-100.0

-90.0

-80.0

-70.0

-60.0

-50.0

-40.0

-30.0

-20.0

-10.0

0.0

0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00

OUTPUT VOLTAGE (V)

IOH (mA)

INPUT CLAMP CURRENT VS. INPUT VOLTAGE

(VCC = 5V, TA = 25°C)

-60

-50

-40

-30

-20

-10

-1.00 -0.80 -0.60 -0.40 -0.20 0.00

INPUT VOLTAGE (V)

INPUT CURRENT (mA)

ATF1504AS(L)

0950O–PLD–7/05

OUTPUT SINK CURRENT VS. SUPPLY VOLTAGE

(VOL = 0.5V, TA = 25°C)

4.50 4.75 5.00 5.25 5.50

SUPPLY VOLTAGE (V)

IOL (mA)

NORMALIZED TPD

VS. SUPPLY VOLTAGE (TA = 25°C)

0.80

0.90

1.00

1.10

1.20

4.5 4.8 5.0 5.3 5.5

SUPPLY VOLTAGE (V)

NORMALIZED TPD

INPUT CURRENT VS. INPUT VOLTAGE

(VCC = 5V, TA = 25°C)

-30

-20

-10

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

INPUT VOLTAGE (V)

INPUT CURRENT ( A)

OUTPUT SINK CURRENT VS. OUTPUT VOLTAGE

(VCC = 5V, TA = 25°C)

0.0

20.0

40.0

60.0

80.0

100.0

120.0

140.0

0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00

OUTPUT VOLTAGE (V)

IOL (mA)

NORMALIZED TPD

VS. TEMPERATURE (VCC = 5.0V)

0.8

0.9

1.0

1.1

1.2

-40.0 0.0 25.0 75.0

TEMPERATURE (C)

NORMALIZED TPD

NORMALIZED TCO

VS. SUPPLY VOLTAGE (TA = 25°C)

0.8

0.9

1.0

1.1

1.2

4.5 4.8 5.0 5.3 5.5

SUPPLY VOLTAGE (V)

NORMALIZED TPD

NORMALIZED TSU

VS. SUPPLY VOLTAGE (TA = 25°C)

0.8

0.9

1.0

1.1

1.2

4.5 4.8 5.0 5.3 5.5

SUPPLY VOLTAGE (V)

NORMALIZED TSU

24 ATF1504AS(L)

0950O–PLD–7/05

NORMALIZED TCO

VS.TEMPERATURE (VCC = 5.0V)

0.8

0.9

1.0

1.1

1.2

-40.0 0.0 25.0 75.0

TEMPERATURE (C)

NORMALIZED TCO

NORMALIZED TSU

VS. TEMPERATURE (VCC = 5.0V)

0.8

0.9

1.0

1.1

1.2

-40.0 0.0 25.0 75.0

TEMPERATURE (C)

NORMALIZED TSU

ATF1504AS(L)

0950O–PLD–7/05

Ordering Information

Notes: 1. The last time buy date is Sept. 30, 2005 for shaded parts.

2. For the QC100 package, customers may migrate to the ATF1508AS-10QU100 or AU100.

Using “C” Product for Industrial

To use commercial product for Industrial temperature ranges, down-grade one speed grade from the “I” to the “C” device

(7 ns “C” = 10 ns “I”) and de-rate power by 30%.

ATF1504AS Standard Package Options

tPD

(ns)

tCO1

(ns)

fMAX

(MHz) Ordering Code Package Operation Range

7.5 4.5 166.7

ATF1504AS-7 AC44

ATF1504AS-7 JC44

ATF1504AS-7 JC68

ATF1504AS-7 JC84

ATF1504AS-7 QC100

ATF1504AS-7 AC100

44A

44J

68J

84J

100Q1

100A

Commercial

(0°C to 70°C)

10 5 125

ATF1504AS-10 AC44 44A

Commercial

(0°C to 70°C)

ATF1504AS-10 JC44 44J

ATF1504AS-10 JC68 68J

ATF1504AS-10 JC84 84J

ATF1504AS-10 QC100 100Q1

ATF1504AS-10 AC100 100A

10 5 125

ATF1504AS-10 AI44

ATF1504AS-10 JI44

ATF1504AS-10 JI68

ATF1504AS-10 JI84

ATF1504AS-10 QI100

ATF1504AS-10 AI100

44A

44J

68J

84J

100Q1

100A

Industrial

(-40°C to +85°C)

15 8 100

ATF1504AS-15 AC44

ATF1504AS-15 JC44

44A

44J

Commercial

(0°C to 70°C)

ATF1504AS-15 JC68 68J

ATF1504AS-15 JC84 84J

ATF1504AS-15 QC100 100Q1

ATF1500AS-15 AC100 100A

15 8 100

ATF1504AS-15 AI44

ATF1504AS-15 JI44

ATF1504AS-15 JI68

ATF1504AS-15 JI84

ATF1504AS-15 QI100

ATF1504AS-15 AI100

44A

44J

68J

84J

100Q1

100A

Industrial

(-40°C to +85°C)

26 ATF1504AS(L)

0950O–PLD–7/05

ATF1504AS Green Package Options (Pb/Halide-free/RoHS Compliant)

tPD

(ns)

tCO1

(ns)

fMAX

(MHz) Ordering Code Package Operation Range

7.5 4.5 166.7 ATF1504AS-7 AX44

ATF1504AS-7 JX44

44A

44J

Commercial

(0°C to 70°C)

10 5 125

ATF1504AS-10 AU44 44A Industrial

(-40°C to +85°C)

ATF1504AS-10 JU44 44J

ATF1504AS-10AU100 100A

ATF1504AS-10 JU84 84J

Package Type

44A 44-lead, Thin Plastic Gull Wing Quad Flatpack (TQFP)

44J 44-lead, Plastic J-leaded Chip Carrier (PLCC)

68J 68-lead, Plastic J-leaded Chip Carrier (PLCC)

84J 84-lead, Plastic J-leaded Chip Carrier (PLCC)

100Q1 100-lead, 14 x 20 mm Body, Plastic Quad Flat Package (PQFP)

100A 100-lead, 14 x 14 mm Body, Thin Profile Plastic Quad Flat Package (TQFP)

ATF1504AS(L)

0950O–PLD–7/05

Note: 1. The last time buy date is Sept. 30, 2005 for shaded parts.

Using “C” Product for Industrial

To use commercial product for Industrial temperature ranges, down-grade one speed grade from the “I” to the “C” device

(7 ns “C” = 10 ns “I”) and de-rate power by 30%.

ATF1504ASL Standard Package Options

tPD

(ns)

tCO1

(ns)

fMAX

(MHz) Ordering Code Package Operation Range

20 12 83.3

ATF1504ASL-20 AC44 44A

44J

68J

84J

100Q1

100A

Commercial

(0°C to 70°C)

ATF1504ASL-20 JC44

ATF1504ASL-20 JC68

ATF1504ASL-20 JC84

ATF1504ASL-20 QC100

ATF1504ASL-20 AC100

25 15 70

ATF1504ASL-25 AI44 44A

44J

68J

84J

100Q1

100A

Industrial

(-40°C to +85°C)

ATF1504ASL-25 JI84

ATF1504ASL-25 JI68

ATF1504ASL-25 JI84

ATF1504ASL-25 QI100

ATF1504ASL-25 AI100

ATF1504ASL Green Package Options (Pb/Halide-free/RoHS Compliant)

tPD

(ns)

tCO1

(ns)

fMAX

(MHz) Ordering Code Package Operation Range

25 15 70

ATF1504ASL-25 AU44

ATF1504ASL-25 JU44

ATF1504ASL-25 AU100

44A

44J

100A

Industrial

(-40°C to +85°C)

Package Type

44A 44-lead, Thin Plastic Gull Wing Quad Flatpack (TQFP)

44J 44-lead, Plastic J-leaded Chip Carrier (PLCC)

68J 68-lead, Plastic J-leaded Chip Carrier (PLCC)

84J 84-lead, Plastic J-leaded Chip Carrier (PLCC)

100Q1 100-lead, 14 x 20 mm Body, Plastic Quad Flat Package (PQFP)

100A 100-lead, 14 x 14 mm Body, Thin Profile Plastic Quad Flat Package (TQFP)

28 ATF1504AS(L)

0950O–PLD–7/05

Packaging Information

44A – TQFP

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness,

0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B

44A

10/5/2001

PIN 1 IDENTIFIER

0˚~7˚

PIN 1

A1 A2 A

eE1 E

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB.

2. Dimensions D1 and E1 do not include mold protrusion. Allowable

protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum

plastic body size dimensions including mold mismatch.

3. Lead coplanarity is 0.10 mm maximum.

A – – 1.20

A1 0.05 – 0.15

A2 0.95 1.00 1.05

D 11.75 12.00 12.25

D1 9.90 10.00 10.10 Note 2

E 11.75 12.00 12.25

E1 9.90 10.00 10.10 Note 2

B 0.30 – 0.45

C 0.09 – 0.20

L 0.45 – 0.75

e 0.80 TYP

ATF1504AS(L)

0950O–PLD–7/05

44J – PLCC

Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC.

2. Dimensions D1 and E1 do not include mold protrusion.

Allowable protrusion is .010"(0.254 mm) per side. Dimension D1

and E1 include mold mismatch and are measured at the extreme

material condition at the upper or lower parting line.

3. Lead coplanarity is 0.004" (0.102 mm) maximum.

A 4.191 – 4.572

A1 2.286 – 3.048

A2 0.508 – –

D 17.399 – 17.653

D1 16.510 – 16.662 Note 2

E 17.399 – 17.653

E1 16.510 – 16.662 Note 2

D2/E2 14.986 – 16.002

B 0.660 – 0.813

B1 0.330 – 0.533

e 1.270 TYP

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

1.14(0.045) X 45˚ PIN NO. 1

IDENTIFIER

1.14(0.045) X 45˚

0.51(0.020)MAX

0.318(0.0125)

0.191(0.0075)

45˚ MAX (3X)

B1 D2/E2

E1 E

44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) B

44J

10/04/01

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

30 ATF1504AS(L)

0950O–PLD–7/05

68J – PLCC

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

68J, 68-lead, Plastic J-leaded Chip Carrier (PLCC) B

68J

10/04/01

1.14(0.045) X 45˚ PIN NO. 1

IDENTIFIER

1.14(0.045) X 45˚

0.51(0.020)MAX

0.318(0.0125)

0.191(0.0075)

45˚ MAX (3X)

B1 D2/E2

E1 E

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

Notes: 1. This package conforms to JEDEC reference MS-018, Variation AE.

2. Dimensions D1 and E1 do not include mold protrusion.

Allowable protrusion is .010"(0.254 mm) per side. Dimension D1

and E1 include mold mismatch and are measured at the extreme

material condition at the upper or lower parting line.

3. Lead coplanarity is 0.004" (0.102 mm) maximum.

A 4.191 – 4.572

A1 2.286 – 3.048

A2 0.508 – –

D 25.019 – 25.273

D1 24.130 – 24.333 Note 2

E 25.019 – 25.273

E1 24.130 – 24.333 Note 2

D2/E2 22.606 – 23.622

B 0.660 – 0.813

B1 0.330 – 0.533

e 1.270 TYP

ATF1504AS(L)

0950O–PLD–7/05

84J – PLCC

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

84J, 84-lead, Plastic J-leaded Chip Carrier (PLCC) B

84J

10/04/01

1.14(0.045) X 45˚ PIN NO. 1

IDENTIFIER

1.14(0.045) X 45˚

0.51(0.020)MAX

0.318(0.0125)

0.191(0.0075)

45˚ MAX (3X)

B1 D2/E2

E1 E

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

Notes: 1. This package conforms to JEDEC reference MS-018, Variation AF.

2. Dimensions D1 and E1 do not include mold protrusion.

Allowable protrusion is .010"(0.254 mm) per side. Dimension D1

and E1 include mold mismatch and are measured at the extreme

material condition at the upper or lower parting line.

3. Lead coplanarity is 0.004" (0.102 mm) maximum.

A 4.191 – 4.572

A1 2.286 – 3.048

A2 0.508 – –

D 30.099 – 30.353

D1 29.210 – 29.413 Note 2

E 30.099 – 30.353

E1 29.210 – 29.413 Note 2

D2/E2 27.686 – 28.702

B 0.660 – 0.813

B1 0.330 – 0.533

e 1.270 TYP

32 ATF1504AS(L)

0950O–PLD–7/05

100Q1 – PQFP

PIN 1 ID

0º~7º

JEDEC STANDARD MS-022, GC-1

PIN 1

07/6/2005

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

100Q1, 100-lead, 14 x 20 mm Body, 3.2 mm Footprint, 0.65 mm Pitch,

Plastic Quad Flat Package (PQFP) C

100Q1

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

A – 3.04 3.4

A1 0.25 0.33 0.5

D 23.20 BSC

E 17.20 BSC

E1 14.00 BSC

B 0.22 – 0.40

C 0.11 – 0.23

D1 20 BSC

L 0.73 – 1.03

e 0.65 BSC

ATF1504AS(L)

0950O–PLD–7/05

100A – TQFP

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

100A, 100-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness,

0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) C

100A

10/5/2001

PIN 1 IDENTIFIER

0˚~7˚

PIN 1

A1 A2 A

eE1 E

A – – 1.20

A1 0.05 – 0.15

A2 0.95 1.00 1.05

D 15.75 16.00 16.25

D1 13.90 14.00 14.10 Note 2

E 15.75 16.00 16.25

E1 13.90 14.00 14.10 Note 2

B 0.17 – 0.27

C 0.09 – 0.20

L 0.45 – 0.75

e 0.50 TYP

Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED.

2. Dimensions D1 and E1 do not include mold protrusion. Allowable

protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum

plastic body size dimensions including mold mismatch.

3. Lead coplanarity is 0.08 mm maximum.

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

34 ATF1504AS(L)

0950O–PLD–7/05

Revision History

Revision Comments

0950O Green package options added.

Printed on recycled paper.

0950O–PLD–7/05 xM

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any

intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-

TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY

WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-

TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT

OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no

representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications

and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided

otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use

as components in applications intended to support or sustain life.

Atmel Corporation Atmel Operations

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 487-2600

Regional Headquarters

Europe

Atmel Sarl

Route des Arsenaux 41

Case Postale 80

CH-1705 Fribourg

Switzerland

Tel: (41) 26-426-5555

Fax: (41) 26-426-5500

Asia

Room 1219

Chinachem Golden Plaza

77 Mody Road Tsimshatsui

East Kowloon

Hong Kong

Tel: (852) 2721-9778

Fax: (852) 2722-1369

Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

Japan

Tel: (81) 3-3523-3551

Fax: (81) 3-3523-7581

Memory

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 436-4314

Microcontrollers

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 436-4314

La Chantrerie

BP 70602

44306 Nantes Cedex 3, France

Tel: (33) 2-40-18-18-18

Fax: (33) 2-40-18-19-60

ASIC/ASSP/Smart Cards

Zone Industrielle

13106 Rousset Cedex, France

Tel: (33) 4-42-53-60-00

Fax: (33) 4-42-53-60-01

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906, USA

Tel: 1(719) 576-3300

Fax: 1(719) 540-1759

Scottish Enterprise Technology Park

Maxwell Building

East Kilbride G75 0QR, Scotland

Tel: (44) 1355-803-000

Fax: (44) 1355-242-743

RF/Automotive

Theresienstrasse 2

Postfach 3535

74025 Heilbronn, Germany

Tel: (49) 71-31-67-0

Fax: (49) 71-31-67-2340

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906, USA

Tel: 1(719) 576-3300

Fax: 1(719) 540-1759

Biometrics/Imaging/Hi-Rel MPU/

High Speed Converters/RF Datacom

Avenue de Rochepleine

BP 123

38521 Saint-Egreve Cedex, France

Tel: (33) 4-76-58-30-00

Fax: (33) 4-76-58-34-80

Literature Requests

www.atmel.com/literature

marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.