Product Folder Order Now Support & Community Tools & Software Technical Documents Reference Design LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 LMZ10500 650-mA Nano Module With 5.5-V Maximum Input Voltage 1 Features 2 Applications * * * * * * * * * * * * * * * 1 * * * * * * Output Current Up to 650 mA Input Voltage Range 2.7 V to 5.5 V Output Voltage Range 0.6 V to 3.6 V Efficiency up to 95% Integrated Inductor 8-Pin microSiP Footprint -40C to 125C Junction Temperature Range Adjustable Output Voltage 2-MHz Fixed PWM Switching Frequency Integrated Compensation Soft-Start Function Current Limit Protection Thermal Shutdown Protection Input Voltage UVLO for Power-Up, Power-Down, and Brownout Conditions Only 5 External Components -- Resistor Divider and 3 Ceramic Capacitors Small Solution Size Low Output Voltage Ripple Easy Component Selection and Simple PCB Layout High Efficiency Reduces System Heat Generation Create a Custom Design Using the LMZ10500 With the WEBENCH(R) Power Designer Typical Efficiency at VIN = 3.6 V 3 Description The LMZ10500 nano module is an easy-to-use stepdown DC/DC solution capable of driving up to 650 mA load in space-constrained applications. Only an input capacitor, an output capacitor, a small VCON filter capacitor, and two resistors are required for basic operation. The nano module comes in an 8-pin SiP footprint package with an integrated inductor. Internal current limit based soft-start function, current overload protection, and thermal shutdown are also provided. Device Information(1) PART NUMBER LMZ10500 PACKAGE BODY SIZE (NOM) SiP (8) 3.00 mm x 2.60 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. space space space space space Radiated EMI (CISPR22) VIN = 5 V, VOUT = 1.8 V, IOUT = 650 mA 100 90 80 80 70 EN 55022 Class B Limit 60 EN 55022 Class A Limit Radiated Emissions (dBV/m) EFFICIENCY (%) * * Point of Load Conversions From 3.3-V and 5-V Rails Space Constrained Applications Low Output Noise Applications 70 60 50 VOUT=1.2V VOUT=1.8V VOUT=2.5V VOUT=3.3V 40 30 20 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) C009 Evaluation Board 50 40 30 20 10 0 0 200 400 600 Frequency (MHz) 800 1000 C001 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 6.7 4 4 4 4 5 6 7 Detailed Description .............................................. 9 7.1 7.2 7.3 7.4 8 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... System Characteristics ............................................. Typical Characteristics .............................................. Overview ................................................................... 9 Functional Block Diagram ......................................... 9 Feature Description................................................... 9 Device Functional Modes........................................ 11 Application and Implementation ........................ 13 8.1 Application Information............................................ 13 8.2 Typical Application ................................................. 13 9 Power Supply Recommendations...................... 20 9.1 Voltage Range ........................................................ 20 9.2 Current Capability ................................................... 20 9.3 Input Connection .................................................... 20 10 Layout................................................................... 21 10.1 Layout Guidelines ................................................. 21 10.2 Layout Example .................................................... 21 10.3 Package Considerations ....................................... 22 11 Device and Documentation Support ................. 23 11.1 11.2 11.3 11.4 11.5 11.6 11.7 Device Support .................................................... Documentation Support ........................................ Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 23 23 23 23 23 23 23 12 Mechanical, Packaging, and Orderable Information ........................................................... 24 12.1 Tape and Reel Information ................................... 24 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision F (February 2015) to Revision G Page * editorial rebranding for SEO ................................................................................................................................................... 1 * Added links for Webench ....................................................................................................................................................... 1 * Move storage temperature spec to Abs Max table ................................................................................................................ 4 * Changed "Handling" to "ESD" Ratings .................................................................................................................................. 4 * Added Device Support ......................................................................................................................................................... 23 * Changed SIL package drawing to SIL0008G ...................................................................................................................... 24 Changes from Revision E (September 2014) to Revision F * Switched Figure 16 and Figure 17 ....................................................................................................................................... 15 Changes from Revision D (January 2014) to Revision E * 2 Page Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................................................................................................... 1 Changes from Revision C (March 2013) to Revision D * Page Page Added new package SIL0008A .............................................................................................................................................. 3 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 5 Pin Configuration and Functions SIL Package 8-Pin SIP SIDE VIEW TOP VIEW BOTTOM VIEW 1 8 8 VREF 2 7 7 VIN EN 1 VCON 2 FB 3 SGND 4 PAD 3 6 6 PGND 4 5 5 VOUT (SGND) Pin Functions PIN NO. NAME I/O DESCRIPTION 1 EN I Enable input. Set this digital input higher than 1.2 V for normal operation. For shutdown, set low. Pin is internally pulled up to VIN and can be left floating for always-on operation. 2 VCON I Output voltage control pin. Connect to analog voltage from resisitve divider or DAC/controller to set the VOUT voltage. VOUT = 2.5 x VCON. Connect a small (470 pF) capacitor from this pin to SGND to provide noise filtering. 3 FB I Feedback of the error amplifier. Connect directly to output capacitor to sense VOUT. 4 SGND I Ground for analog and control circuitry. Connect to PGND at a single point. 5 VOUT O Output Voltage. Connected to one pin of the integrated inductor. Connect output filter capacitor between VOUT and PGND. 6 PGND I Power ground for the power MOSFETs and gate-drive circuitry. 7 VIN I Voltage supply input. Connect ceramic capacitor between VIN and PGND as close as possible to these two pins. Typical capacitor values are between 4.7 F and 22 F. 8 VREF O 2.35 V voltage reference output. Typically connected to VCON pin through a resistive divider to set the output voltage. -- PAD I The center pad underneath the SIL0008A package is internally tied to SGND. Connect this pad to the ground plane for improved thermal performance. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 3 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) MIN MAX UNIT -0.2 6 V PGND to SGND -0.2 0.2 V EN, FB, VCON (SGND - 0.2) to (VIN + 0.2) 6 V VOUT (PGND - 0.2) to (VIN + 0.2) 6 V -40 125 C 260 C 150 C VIN, VREF to SGND Junction temperature (TJ-MAX) Maximum lead temperature Storage temperature, Tstg (1) (2) -65 Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are conditions under which operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/ Distributors for availability and specifications. 6.2 ESD Ratings VALUE Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 V(ESD) (1) (2) Electrostatic discharge (1) UNIT 1000 Charged-device model (CDM), per JEDEC specification JESD22C101 (2) V 250 JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN Input voltage Recommended load current Junction temperature (TJ) MAX UNIT 2.7 5.5 V 0 650 mA -40 125 C 6.4 Thermal Information LMZ10500 THERMAL METRIC (1) SIL (SIP) UNIT 8 PINS RJA Junction-to-ambient thermal resistance 45.8 C/W RJC(top) Junction-to-case (top) thermal resistance 25 C/W RJB Junction-to-board thermal resistance 9.2 C/W JT Junction-to-top characterization parameter 1.5 C/W JB Junction-to-board characterization parameter 9.1 C/W RJC(bot) Junction-to-case (bottom) thermal resistance 25 C/W (1) 4 SIL0008G Package For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 6.5 Electrical Characteristics Minimum and maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 3.6 V, VEN = 1.2 V, TJ = 25C (1) PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT 5.875 5.9925 V V/V SYSTEM PARAMETERS VREF x GAIN Reference voltage x VCON to FB Gain VIN = VEN = 5.5 V, VCON = 1.44 V 5.7575 GAIN VCON to FB Gain VIN = 5.5 V, VCON = 1.44 V 2.4375 2.5 2.575 VINUVLO VIN rising threshold 2.24 2.41 2.64 V VINUVLO VIN UVLO Hysteresis 120 165 200 mV HYST ISHDN Shutdown supply current VIN = 3.6 V, VEN = 0.5 V (3) 11 18 A Iq DC bias current into VIN VIN = 5.5 V, VCON = 1.6 V, IOUT = 0 A 6.5 9.5 mA RDROPOUT VIN to VOUTresistance IOUT = 200 mA 305 575 m 2.25 MHz I LIM DC Output Current Limit 800 1000 FOSC Internal oscillator frequency 1.75 2 VIH,ENABLE Enable logic HIGH voltage 1.2 VIL,ENABLE Enable logic LOW voltage TSD Thermal shutdown TSD-HYST Thermal shutdown hysteresis DMAX Maximum duty cycle TON-MIN Minimum on-time Package Thermal Resistance JA (1) (2) (3) (4) VCON = 1.72 V (4) mA V 0.5 Rising Threshold V 150 C 20 C 100% 50 20-mm x 20-mm board 2 layers, 2 oz copper, 0.5W, no airlow 77 15 mm x 15 mm board 2 layers, 2 oz copper, 0.5W, no airlow 88 10 mm x 10 mm board 2 layers, 2 oz copper, 0.5W, no airlow 107 ns C/W Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate the Average Outgoing Quality Level (AOQL). Typical numbers are at 25C and represent the most likely parametric norm. Shutdown current includes leakage current of the high side PFET. Current limit is built-in, fixed, and not adjustable. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 5 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 6.6 System Characteristics The following specifications are ensured by design providing the component values in Figure 13 are used (CIN = COUT = 10 F, 6.3 V, 0603, TDK C1608X5R0J106K). These parameters are not ensured by production testing. Unless otherwise stated the following conditions apply: TA = 25C. PARAMETER VOUT/VOUT VOUT/VOUT VOUT/VOUT VREF TRISE TEST CONDITIONS MIN TYP Output Voltage Regulation Over Line Voltage and Load Current VOUT = 0.6 V VIN =2.7 V to 4.2 V IOUT = 0 A to 650 mA 1.23% Output Voltage Regulation Over Line Voltage and Load Current VOUT = 1.5 V VIN = 2.7 V to 5.5 V IOUT = 0 A to 650 mA 0.56% Output Voltage Regulation Over Line Voltage and Load Current VOUT = 3.6 V VIN = 4.0 V to 5.5 V IOUT = 0 A to 650 mA 0.24% Rise time of reference voltage EN = Low to High, VIN = 4.2 V VOUT = 2.7 V, IOUT = 650 mA 10 MAX UNIT s VIN = 5.0 V, VOUT = 3.3 V IOUT = 200 mA 95% Full Load Efficiency VIN = 5.0 V, VOUT = 3.6 V IOUT = 650 mA 93% VOUT Ripple Output voltage ripple VIN = 5.0 V, VOUT = 1.8 V IOUT = 650 mA (1) 8 mV pkpk Line Transient Line transient response VIN = 2.7 V to 5.5 V, TR = TF= 10 s, VOUT = 1.8 V, IOUT = 650 mA 25 mV pkpk Load transient response VIN = 5.0 V TR = TF = 40 s, VOUT = 1.8 V IOUT = 65 mA to 650 mA 25 mV pkpk Peak Efficiency Load Transient (1) 6 Ripple voltage should be measured across COUT on a well-designed PC board using the suggested capacitors. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 6.7 Typical Characteristics Unless otherwise specified the following conditions apply: VIN = 3.6 V, TA = 25C 0.30 DROPOUT VOLTAGE (V) VOUT RIPPLE COUT = 10 F 10V 0805 X5R 10mV/Div 0.25 0.20 0.15 0.10 VIN=2.7V VIN=3V VIN=3.3V VIN=3.6V 0.05 0.00 250MHz BW 0 1s/Div 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) 0.7 0.7 0.6 0.6 0.5 0.4 0.3 0.2 VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 0.1 0.0 60 70 0.5 0.4 0.3 0.2 VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 0.1 0.0 80 90 100 110 120 AMBIENT TEMPREATURE (C) 130 60 70 0.6 OUTPUT CURRENT (A) OUTPUT CURRENT (A) 0.7 0.5 0.4 0.3 0.2 VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 70 100 110 AMBIENT TEMPERATURE (C) 120 130 C002 0.4 0.3 0.2 VIN=4V VIN=4.5V VIN=5V VIN=5.5V 0.0 90 110 0.5 0.1 80 100 Figure 4. Thermal Derating VOUT = 1.8 V, JA = 77C/W 0.6 60 90 AMBIENT TEMPERATURE (C) 0.7 0.0 80 C001 Figure 3. Thermal Derating VOUT = 1.2 V, JA = 77C/W 0.1 C010 Figure 2. Dropout Voltage vs Load Current and Input Voltage OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 1. Output Voltage Ripple VIN = 5 V, VOUT = 1.8 V, IOUT = 650 mA 120 130 60 C003 Figure 5. Thermal Derating VOUT = 2.5 V, JA = 77C/W 70 80 90 100 110 120 AMBIENT TEMPERATURE (C) 130 C004 Figure 6. Thermal Derating VOUT = 3.3 V, RJA = 77C/W Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 7 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com Typical Characteristics (continued) Unless otherwise specified the following conditions apply: VIN = 3.6 V, TA = 25C 100 Evaluation Board 70 EN 55022 Class B Limit 60 EN 55022 Class A Limit Peak Emissions Quasi Peak Limit Average Limit 90 Radiated Emissions (dBV/m) Radiated Emissions (dBV/m) 80 50 40 30 20 10 80 70 60 50 40 30 20 10 0 0 0 200 400 600 800 Frequency (MHz) VIN = 5 V 1000 0.1 1 VOUT = 1.8 V IOUT = 650 mA Figure 7. Radiated EMI (CISPR22) Default Evaluation Board BOM 10 Frequency (MHz) C001 VIN = 5 V VOUT = 1.8 V 100 C001 IOUT = 650 mA Figure 8. Conducted EMI Default Evaluation Board BOM With Additional 2.2h 1f LC Input Filter VCON 500 mV/Div 200 mA/Div IL 200 mA/Div IOUT VOUT 500 mV/Div 10 s/Div Figure 9. Startup 8 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 7 Detailed Description 7.1 Overview The LMZ10500 nano module is an easy-to-use step-down DC/DC solution capable of driving up to 650 mA load in space-constrained applications. Only an input capacitor, an output capacitor, a small VCON filter capacitor, and two resistors are required for basic operation. The nano module comes in 8-pin LLP footprint package with an integrated inductor. The LMZ10500 operates in fixed 2-MHz PWM (Pulse Width Modulation) mode, and is designed to deliver power at maximum efficiency. The output voltage is typically set by using a resistive divider between the built-in reference voltage VREF and the control pin VCON. The VCON pin is the positive input to the error amplifier. The output voltage of the LMZ10500 can also be dynamically adjusted between 0.6 V and 3.6 V by driving the VCON pin externally. Internal current limit based soft-start function, current overload protection, and thermal shutdown are also provided. 7.2 Functional Block Diagram VREF VIN UVLO REFERENCE VOLTAGE VCON ERROR AMPLIFIER FB COMP CURRENT COMP CURRENT SENSE L VOUT MOSFET CONTROL LOGIC Integrated Inductor VIN UVLO EN MAIN CONTROL TSD OSCILLATOR SGND PGND 7.3 Feature Description 7.3.1 Current Limit The LMZ10500 current limit feature protects the module during an overload condition. The circuit employs positive peak current limit in the PFET and negative peak current limit in the NFET switch. The positive peak current through the PFET is limited to 1.2 A (typical). When the current reaches this limit threshold the PFET switch is immediately turned off until the next switching cycle. This behavior continues on a cycle-by-cycle basis until the overload condition is removed from the output. The typical negative peak current limit through the NFET switch is -0.6A (typical). The ripple of the inductor current depends on the input and output voltages. This means that the DC level of the output current when the peak current limiting occurs will also vary over the line voltage and the output voltage level. Refer to the DC Output Current Limit plots in the Typical Characteristics section for more information. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 9 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com Feature Description (continued) 7.3.2 Start-up Behavior and Soft Start The LMZ10500 features a current limit based soft-start circuit in order to prevent large in-rush current and output overshoot as VOUT is ramping up. This is achieved by gradually increasing the PFET current limit threshold to the final operating value as the output voltage ramps during startup. The maximum allowed current in the inductor is stepped up in a staircase profile for a fixed number of switching periods in each step. Additionally, the switching frequency in the first step is set at 450 kHz and is then increased for each of the following steps until it reaches 2MHz at the final step of current limiting. This current limiting behavior is illustrated in Figure 10 and allows for a smooth VOUT ramp up. VCON 500 mV/Div 200 mA/Div IL 200 mA/Div 500 mV/Div IOUT VOUT 10 s/Div Figure 10. Startup Behavior of Current Limit Based softstart The soft start rate is also limited by the VCON ramp up rate. The VCON pin is discharged internally through a pull down device before startup occurs. This is done to deplete any residual charge on the VCON filter capacitor and allow the VCON voltage to ramp up from 0V when the part is started. The events that cause VCON discharge are thermal shutdown, UVLO, EN low, or output short circuit detection. The minimum recommended capacitance on VCON is 220 pF and the maximum is 1 nF. The duration of startup current limiting sequence takes approximately 75 s. After the sequence is completed, the feedback voltage is monitored for output short circuit events. 7.3.3 Output Short Circuit Protection In addition to cycle by cycle current limit, the LMZ10500 features a second level of short circuit protection. If the load pulls the output voltage down and the feedback voltage falls to 0.375 V, the output short circuit protection will engage. In this mode the internal PFET switch is turned OFF after the current limit comparator trips and the beginning of the next cycle is inhibited for approximately 230 s. This forces the inductor current to ramp down and limits excessive current draw from the input supply when the output of the regulator is shorted. The synchronous rectifier is always OFF in this mode. After 230 s of non-switching a new startup sequence is initiated. During this new startup sequence the current limit is gradually stepped up to the nominal value as illustrated in the Start-up Behavior and Soft Start section. After the startup sequence is completed again, the feedback voltage is monitored for output short circuit. If the short circuit is still persistent after the new startup sequence, switching will be stopped again and there will be another 230 s off period. A persistent output short condition results in a hiccup behavior where the LMZ10500 goes through the normal startup sequence, then detects the output short at the end of startup, terminates switching for 230 s, and repeats this cycle until the output short is released. This behavior is illustrated in Figure 11. VOUT IIN IL VCON 1V/Div 100 s/Div 50 mA/Div 0.3A/Div 1V/Div Figure 11. Hiccup Behavior With Persistent Output Short Circuit 10 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 Feature Description (continued) Because the output current is limited during normal startup by the softstart function, the current charging the output capacitor is also limited. This results in a smooth VOUT ramp up to nominal voltage. However, using excessively large output capacitance or VCON capacitance under normal conditions can prevent the output voltage from reaching 0.375 V at the end of the startup sequence. In such cases the module will maintain the described above hiccup mode and the output voltage will not ramp up to final value. To cause this condition, one would have to use unnecessarily large output capacitance for 650mA load applications. See the Input and Output Capacitor Selection section for guidance on maximum capacitances for different output voltage settings. 7.3.4 Thermal Overload Protection The junction temperature of the LMZ10500 should not be allowed to exceed its maximum operating rating of 125C. Thermal protection is implemented by an internal thermal shutdown circuit which activates at 150C (typ). When this temperature is reached, the device enters a low power standby state. In this state switching remains off causing the output voltage to fall. Also, the VCON capacitor is discharged to SGND. When the junction temperature falls back below 130C (typ) normal startup occurs and VOUT rises smoothly from 0 V. Applications requiring maximum output current may require derating at elevated ambient temperature. See Typical Characteristics for thermal derating plots for various output voltages. 7.4 Device Functional Modes 7.4.1 Circuit Operation The LMZ10500 is a synchronous Buck power module using a PFET for the high side switch and an NFET for the synchronous rectifier switch. The output voltage is regulated by modulating the PFET switch on-time. The circuit generates a duty-cycle modulated rectangular signal. The rectangular signal is averaged using a low pass filter formed by the integrated inductor and an output capacitor. The output voltage is equal to the average of the dutycycle modulated rectangular signal. In PWM mode, the switching frequency is constant. The energy per cycle to the load is controlled by modulating the PFET on-time, which controls the peak inductor current. In current mode control architecture, the inductor current is compared with the slope compensated output of the error amplifier. At the rising edge of the clock, the PFET is turned ON, ramping up the inductor current with a slope of (VIN - VOUT) / L. The PFET is ON until the current signal equals the error signal. Then the PFET is turned OFF and NFET is turned ON, ramping down the inductor current with a slope of VOUT / L. At the next rising edge of the clock, the cycle repeats. An increase of load pulls the output voltage down, resulting in an increase of the error signal. As the error signal goes up, the peak inductor current is increased, elevating the average inductor current and responding to the heavier load. To ensure stability, a slope compensation ramp is subtracted from the error signal and internal loop compensation is provided. 7.4.2 Input Undervoltage Detection The LMZ10500 implements an under voltage lock out (UVLO) circuit to ensure proper operation during startup, shutdown and input supply brownout conditions. The circuit monitors the voltage at the VIN pin to ensure that sufficient voltage is present to bias the regulator. If the under voltage threshold is not met, all functions of the controller are disabled and the controller remains in a low power standby state. 7.4.3 Shutdown Mode To shutdown the LMZ10500, pull the EN pin low (< 0.5 V). In the shutdown mode all internal circuits are turned OFF. 7.4.4 EN Pin Operation The EN pin is internally pulled up to VIN through a 790 k (typical) resistor. This allows the nano module to be enabled by default when the EN pin is left floating. In such cases VIN will set EN high when VIN reaches 1.2 V. As the input voltage continues to rise, operation will start once VIN exceeds the under-voltage lockout (UVLO) threshold. To set EN high externally, pull it up to 1.2 V or higher. Note that the voltage on EN must remain at less than VIN + 0.2 V due to absolute maximum ratings of the device. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 11 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com Device Functional Modes (continued) 7.4.5 Internal Synchronous Rectification The LMZ10500 uses an internal NFET as a synchronous rectifier to minimize the switch voltage drop and increase efficiency. The NFET is designed to conduct through its intrinsic body diode during the built-in dead time between the PFET on-time and the NFET on-time. This eliminates the need for an external diode. The dead time between the PFET and NFET connection prevents shoot through current from VIN to PGND during the switching transitions. 7.4.6 High Duty Cycle Operation The LMZ10500 features a transition mode designed to extend the output regulation range to the minimum possible input voltage. As the input voltage decreases closer and closer to VOUT, the off-time of the PFET gets smaller and smaller and the duty cycle eventually needs to reach 100% to support the output voltage. The input voltage at which the duty cycle reaches 100% is the edge of regulation. When the LMZ10500 input voltage is lowered, such that the off-time of the PFET reduces to less than 35ns, the LMZ10500 doubles the switching period to extend the off-time for that VIN and maintain regulation. If VIN is lowered even more, the off-time of the PFET will reach the 35ns mark again. The LMZ10500 will then reduce the frequency again, achieving less than 100% duty cycle operation and maintaining regulation. As VIN is lowered even more, the LMZ10500 will continue to scale down the frequency, aiming to maintain at least 35ns off time. Eventually, as the input voltage decreases further, 100% duty cycle is reached. This behavior of extending the VIN regulation range is illustrated in Figure 12. 1V/Div INPUT VOLTAGE 1V/Div SWITCH NODE 20 MHz BW 5 s/Div Figure 12. High Duty Cycle Operation and Switching Frequency Reduction 12 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information This section describes a simple design procedure. Alternatively, WEBENCH(R) can be used to create and simulate a design using the LMZ10501. The WEBENCH(R) tool can be accessed from the LMZ10500 product folder at http://www.ti.com/product/lmz10500. For designs with typical output voltages (1.2 V, 1.8 V, 2.5 V, 3.3 V), jump to the Application Curves section for quick reference designs. 8.2 Typical Application EN VREF RT VCON RB CVC FB VIN CIN 10PF PGND SGND VOUT COUT 10PF Figure 13. Typical Application Circuit 8.2.1 Design Requirements The detailed design procedure is based on the required input and output voltage specifications for the design. The input voltage range of the LMZ10500 is 2.7 V to 5.5 V. The output voltage range is 0.6 V to 3.6 V. The output current capability is 650 mA. 8.2.2 Detailed Design Procedure 8.2.2.1 Custom Design With WEBENCH(R) Tools Click here to create a custom design using the LMZ10500 device with the WEBENCH(R) Power Designer. 1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements. 2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial. 3. Compare the generated design with other possible solutions from Texas Instruments. The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time pricing and component availability. In most cases, these actions are available: * Run electrical simulations to see important waveforms and circuit performance * Run thermal simulations to understand board thermal performance * Export customized schematic and layout into popular CAD formats * Print PDF reports for the design, and share the design with colleagues Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 13 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com Typical Application (continued) 8.2.2.2 Setting the Output Voltage The LMZ10500 provides a fixed 2.35-V VREF voltage output. As shown in Figure 13 above, a resistive divider formed by RT and RB sets the VCON pin voltage level. The VOUT voltage tracks VCON and is governed by the following relationship: VOUT = GAIN x VCON where * GAIN is 2.5 V/V from VCON to VFB. (1) This equation is valid for output voltages between 0.6 V and 3.6 V and corresponds to VCON voltage between 0.24 V and 1.44 V, respectively. 8.2.2.2.1 RT and RB Selection for Fixed VOUT The parameters affecting the output voltage setting are the RT, RB, and the product of the VREF voltage x GAIN. The VREF voltage is typically 2.35 V. Since VCON is derived from VREF via RT and RB, VCON = VREF x RB/ (RB + RT) (2) After substitution, VOUT = VREF x GAIN x RB/ (RB + RT) RT = ( GAIN x VREF / VOUT - 1 ) x RB (3) (4) The ideal product of GAIN x VREF = 5.875 V. Choose RT to be between 80 k and 300 k. Then, RB can be calculated using Equation 5. RB = ( VOUT / (5.875V - VOUT) ) x RT (5) Note that the resistance of RT should be 80 k. This ensures that the VREF output current loading is not exceeded and the reference voltage is maintained. The current loading on VREF should not be greater than 30 A. 8.2.2.2.2 Output Voltage Accuracy Optimization Each nano module is optimized to achieve high VOUT accuracy. Equation 1 shows that, by design, the output voltage is a function of the VCON voltage and the gain from VCON to VFB. The voltage at VCON is derived from VREF. Therefore, as shown in Equation 3, the accuracy of the output voltage is a function of the VREF x GAIN product as well as the tolerance of the RT and RB resistors. The typical VREF x GAIN product by design is 5.875V. Each nano module's VREF voltage is trimmed so that this product is as close to the ideal 5.875V value as possible, achieving high VOUT accuracy. See Electrical Characteristics for the VREF x GAIN product tolerance limits. 8.2.2.3 Dynamic Output Voltage Scaling The VCON pin on the LMZ10500 can be driven externally by a DAC to scale the output voltage dynamically. The output voltage VOUT = 2.5 V/V x VCON. When driving VCON with a source different than VREF place a 1.5 k resistor in series with the VCON pin. Current limiting the external VCON helps to protect this pin and allows the VCON capacitor to be fully discharged to 0 V after fault conditions. 8.2.2.4 Integrated Inductor The LMZ10500 includes an inductor with over 1.2A DC current rating and soft saturation profile for up to 2 A. This inductor allows for low package height and provides an easy to use, compact solution with reduced EMI. 8.2.2.5 Input and Output Capacitor Selection The LMZ10500 is designed for use with low ESR multi-layer ceramic capacitors (MLCC) for its input and output filters. Using a 10-F 0603 or 0805 with 6.3-V or 10-V rating ceramic input capacitor typically provides sufficient VIN bypass. Use of multiple 4.7-F or 2.2-F capacitors can also be considered. Ceramic capacitors with X5R and X7R temperature characteristics are recommended for both input and output filters. These provide an optimal balance between small size, cost, reliability, and performance for space sensitive applications. 14 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 Typical Application (continued) The DC voltage bias characteristics of the capacitors must be considered when selecting the DC voltage rating and case size of these components. The effective capacitance of an MLCC is typically reduced by the DC voltage bias applied across its terminals. For example, a typical 0805 case size X5R 6.3-V 10-F ceramic capacitor may only have 4.8 F left in it when a 5.0-V DC bias is applied. Similarly, a typical 0603 case size X5R 6.3-V 10-F ceramic capacitor may only have 2.4 F at the same 5.0-V DC. Smaller case size capacitors may have even larger percentage drop in value with DC bias. The optimum output capacitance value is application dependent. Too small output capacitance can lead to instability due to lower loop phase margin. On the other hand, if the output capacitor is too large, it may prevent the output voltage from reaching the 0.375V required voltage level at the end of the startup sequence. In such cases, the output short circuit protection can be engaged and the nano module will enter a hiccup mode as described in the Output Short Circuit Protection section. Table 1 sets the minimum output capacitance for stability and maximum output capacitance for proper startup for various output voltage settings. Note that the maximum COUT value in Table 1 assumes that the filter capacitance on VCON is the maximum recommended value of 1nF and the RT resistor value is less than 300k. Lower VCON capacitance can extend the maximum COUT range. There is no great performance benefit in using excessive COUT values. Table 1. Output Capacitance Range OUTPUT VOLTAGE MINIMUM COUT SUGGESTED COUT MAXIMUM COUT 0.6 V 4.7 F 10 F 33 F 1V 3.3 F 10 F 33 F 1.2V 3.3 F 10 F 33 F 1.8 V 3.3 F 10 F 47 F 2.5 V 3.3 F 10 F 68 F 3.3V 3.3 F 10 F 68 F Use of multiple 4.7-F or 2.2-F output capacitors can be considered for reduced effective ESR and smaller output voltage ripple. In addition to the main output capacitor, small 0.1-F - 0.01-F parallel capacitors can be used to reduce high frequency noise. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 15 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 8.2.3 Application Curves 8.2.3.1 VOUT = 1.2 V VIN VIN EN 100 1.2V VOUT CIN 90 VOUT 80 EFFICIENCY (%) VREF FB RT VCON PGND RB COUT SGND CVC 70 60 50 VIN=2.7V VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 40 CIN COUT CVC RT RB 10 P) 8 6.3V 10 PF 8 6.3V 470 pF 8 6.3V 243 k: 1% 63.4 k: 1% 0805 X7R or X5R 0805 X7R or X5R 0603 X7R or X5R 0603 0603 30 20 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) C001 Figure 15. Efficiency VOUT = 1.2 V Figure 14. Schematic VOUT = 1.2 V COUT = 10 F 10V 0805 X5R 50mV/Div VOUT RIPPLE COUT = 10 F 10V 0805 X5R OUTPUT VOLTAGE 10mV/Div LOAD CURRENT 500mA/Div 250MHz BW 1s/Div 20 MHz BW Figure 17. Load Transient VOUT = 1.2 V Figure 16. Output Ripple VOUT = 1.2 V 1.8 VIN=2.7V VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 1.23 Typical DC Current Limit (A) OUTPUT VOLTAGE (V) 1.24 1.22 1.21 1.6 1.4 1.2 1.0 0.8 0.6 1.20 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) C002 Figure 18. Line and Load Regulation VOUT = 1.2 V 16 500 s/Div Submit Documentation Feedback 2.5 3.0 3.5 4.0 4.5 Input Voltage (V) 5.0 5.5 C001 Figure 19. DC Current Limit VOUT = 1.2 V Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 8.2.3.2 VOUT = 1.8 V VIN VIN EN 100 1.8V VOUT CIN 90 VOUT 80 EFFICIENCY (%) VREF FB RT VCON PGND RB COUT SGND CVC 70 60 50 VIN=2.7V VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 40 CIN COUT CVC RT RB 10 P) 8 6.3V 10 PF 8 6.3V 470 pF 8 6.3V 187 k: 1% 82.5 k: 1% 0805 X7R or X5R 0805 X7R or X5R 0603 X7R or X5R 0603 0603 30 20 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) C003 Figure 21. Efficiency VOUT = 1.8 V Figure 20. Schematic VOUT = 1.8 V COUT = 10 F 10V 0805 X5R 50mV/Div VOUT RIPPLE COUT = 10 F 10V 0805 X5R OUTPUT VOLTAGE 10mV/Div LOAD CURRENT 500mA/Div 250MHz BW 1s/Div 20 MHz BW 500 s/Div Figure 22. Output Ripple VOUT = 1.8 V 1.8 VIN=2.7V VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 1.80 Typical DC Current Limit (A) OUTPUT VOLTAGE (V) 1.81 Figure 23. Load Transient VOUT = 1.8 V 1.79 1.78 1.77 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) 1.6 1.4 1.2 1.0 0.8 0.6 2.5 C004 Figure 24. Line and Load Regulation VOUT = 1.8 V 3.0 3.5 4.0 4.5 5.0 Input Voltage (V) 5.5 C001 Figure 25. DC Current Limit VOUT = 1.8 V Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 17 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 8.2.3.3 VOUT = 2.5 V VIN VIN EN 100 2.5V VOUT CIN 90 VOUT 80 EFFICIENCY (%) VREF FB RT VCON PGND RB COUT SGND CVC 70 60 50 40 CIN COUT CVC RT RB 10 P) 8 6.3V 10 PF 8 6.3V 470 pF 8 6.3V 150 k: 1% 118 k: 1% 0805 X7R or X5R 0805 X7R or X5R 0603 X7R or X5R 0603 0603 VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 30 20 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) C005 Figure 27. Efficiency VOUT = 2.5 V Figure 26. Schematic VOUT = 2.5 V COUT = 10 F 10V 0805 X5R 50mV/Div VOUT RIPPLE COUT = 10 F 10V 0805 X5R OUTPUT VOLTAGE 10mV/Div LOAD CURRENT 500mA/Div 250MHz BW 1s/Div 20 MHz BW Figure 28. Output Ripple VOUT = 2.5 V Figure 29. Load Transient VOUT = 2.5 V 1.8 Typical DC Current Limit (A) OUTPUT VOLTAGE (V) 2.65 2.60 2.55 2.50 VIN=3.3V VIN=3.6V VIN=5V VIN=5.5V 2.45 0 1.6 1.4 1.2 1.0 0.8 0.6 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) 2.5 C006 Figure 30. Line and Load Regulation VOUT = 2.5 V 18 500 s/Div Submit Documentation Feedback 3.0 3.5 4.0 4.5 5.0 Input Voltage (V) 5.5 C001 Figure 31. DC Current Limit VOUT = 2.5 V Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 8.2.3.4 VOUT = 3.3 V VIN VIN EN 100 3.3V VOUT CIN 90 VOUT 80 EFFICIENCY (%) VREF FB RT VCON PGND RB COUT SGND CVC 70 60 50 40 CIN COUT CVC RT RB 10 P) 8 6.3V 10 PF 8 6.3V 470 pF 8 6.3V 118 k: 1% 150 k: 1% 0805 X7R or X5R 0805 X7R or X5R 0603 X7R or X5R 0603 0603 VIN=4V VIN=4.5V VIN=5V VIN=5.5V 30 20 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) C007 Figure 33. Efficiency VOUT = 3.3 V Figure 32. Schematic VOUT = 3.3 V COUT = 10 F 10V 0805 X5R VOUT RIPPLE COUT = 10 F 10V 0805 X5R 50mV/Div OUTPUT VOLTAGE 10mV/Div LOAD CURRENT 500mA/Div 250MHz BW 1s/Div 20 MHz BW Figure 34. Output Ripple VOUT = 3.3 V Figure 35. Load Transient VOUT = 3.3 V 3.30 1.8 Typical DC Current Limit (A) 3.29 OUTPUT VOLTAGE (V) 500 s/Div 3.28 3.27 3.26 3.25 3.24 VIN=4V VIN=4.5V VIN=5V VIN=5.5V 3.23 3.22 0 1.4 1.2 1.0 0.8 0.6 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 LOAD CURRENT (A) 1.6 2.5 C008 Figure 36. Line and Load Regulation VOUT = 3.3 V 3.0 3.5 4.0 4.5 5.0 Input Voltage (V) 5.5 C001 Figure 37. DC Current Limit VOUT = 3.3 V Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 19 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 9 Power Supply Recommendations 9.1 Voltage Range The voltage of the input supply must not exceed the Absolute Maximum Ratings and the Recommended Operating Conditions of the LMZ10500. 9.2 Current Capability The input supply must be able to supply the required input current to the LMZ10500 converter. The required input current depends on the application's minimum required input voltage (VIN-MIN), the required output power (VOUT x IOUT-MAX), and the converter efficiency (). IIN = VOUT x IOUT-MAX / (VIN-MIN x ) For example, for a design with 5-V minimum input voltage,1.8-V output, and 0.5-A maximum load, considering 90% conversion efficiency, the required input current at steady state is 0.2 A. 9.3 Input Connection Long input connection cables can cause issues with the normal operation of any buck converter. 9.3.1 Voltage Drops Using long input wires to connect the supply to the input of any converter adds impedance in series with the input supply. This impedance can cause a voltage drop at the VIN pin of the converter when the output of the converter is loaded. If the input voltage is near the minimum operating voltage, this added voltage drop can cause the converter to drop out or reset. If long wires are used during testing, it is recommended to add some bulk (i.e. electrolytic) capacitance at the input of the converter. 9.3.2 Stability The added inductance of long input cables together with the ceramic (and low ESR) input capacitor can result in an under damped RLC network at the input of the Buck converter. This can cause oscillations on the input and instability. If long wires are used, it is recommended to add some electrolytic capacitance in parallel with the ceramic input capacitor. The electrolytic capacitor's ESR will improve the damping. Use an electrolytic capacitor with CELECTROLYTIC 4 x CCERAMIC and ESRELECTROLYTIC (LCABLE / CCERAMIC) For example, two cables (one for VIN and one for GND), each 1 meter (~3 ft) long with ~1 mm diameter (18AWG), placed 1 cm (~0.4 in) apart will form a rectangular loop resulting in about 1.2 H of inductance. The inductance in this example can be decreased to almost half if the input wires are twisted. Based on a 10-F ceramic input capacitor, the recommended parallel CELECTROLYTIC is 40 F. Using a 47-F capacitor will be sufficient. The recommended ESRELECTROLYTIC 0.35 or larger, based on about 1.2 H of inductance and 10 F of ceramic input capacitance. See application note SNVA489 for more details on input filter design. 20 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 10 Layout 10.1 Layout Guidelines The board layout of any DC/DC switching converter is critical for the optimal performance of the design. Bad PCB layout design can disrupt the operation of an otherwise good schematic design. Even if the regulator still converts the voltage properly, the board layout can mean the difference between passing or failing EMI regulations. In a Buck converter, the most critical board layout path is between the input capacitor ground terminal and the synchronous rectifier ground. The loop formed by the input capacitor and the power FETs is a path for the high di/dt switching current during each switching period. This loop should always be kept as short as possible when laying out a board for any Buck converter. The LMZ10500 integrates the inductor and simplifies the DC/DC converter board layout. Refer to the example layout in Figure 38. There are a few basic requirements to achieve a good LMZ10500 layout. 1. Place the input capacitor CIN as close as possible to the VIN and PGND pins. VIN (pin 7) and PGND (pin 6) on the LMZ10500 are next to each other which makes the input capacitor placement simple. 2. Place the VCON filter capacitor CVC and the RB RT resistive divider as close as possible to the VCON and SGND terminals.The CVC capacitor (not RB) should be the component closer to the VCON pin, as shown in Figure 38. This allows for better bypass of the control voltage set at VCON. 3. Run the feedback trace (from VOUT to FB) away from noise sources. 4. Connect SGND to a quiet GND plane. 5. Provide enough PCB area for proper heatsinking. Refer to the Electrical Characteristics table for example JA values for different board areas. Also, refer to AN-2020 for additional thermal design hints. Refer to the evaluation board user guide SNVU313 for a complete board layout example. 10.2 Layout Example RB RESISTOR RT RESISTOR HIGH di/dt LOOP KEEP IT SMALL EN VREF VCON VIN FB PGND SGND VOUT VIN INPUT CAPACITOR PGND VOUT FEEDBACK TRACE SGND CONNECTION TO QUIET PGND PLANE OUTPUT CAPACITOR VCON CAPACITOR Figure 38. Example Top Layer Board Layout Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 21 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 10.3 Package Considerations Use the following recommendations when utilizing machine placement : * Use 1.06 mm (42 mil) or smaller nozzle size. The pickup area is the top of the inductor, which is 1.6 mm x 2 mm. * Soft tip pick and place nozzle is recommended. * Add 0.05 mm to the component thickness so that the device will be released 0.05 mm (2 mil) into the solder paste without putting pressure or splashing the solder paste. * Slow the pick arm when picking the part from the tape and reel carrier and when depositing the IC on the board. * If the machine releases the component by force, use minimum force or no more than 3 Newtons. For manual placement: * Use a vacuum pick up hand tool with soft tip head. * If vacuum pick up tool is not available, use non-metal tweezers and hold the part by sides. * Use minimal force when picking and placing the module on the board. * Using hot air station provides better temperature control and better controlled air flow than a heat gun. * Go to the video section at www.ti.com/product/lmz10500 for a quick video on how to solder rework the LMZ10500. 22 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 11 Device and Documentation Support 11.1 Device Support 11.1.1 Custom Design With WEBENCH(R) Tools Click here to create a custom design using the LMZ10500 device with the WEBENCH(R) Power Designer. 1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements. 2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial. 3. Compare the generated design with other possible solutions from Texas Instruments. The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time pricing and component availability. In most cases, these actions are available: * Run electrical simulations to see important waveforms and circuit performance * Run thermal simulations to understand board thermal performance * Export customized schematic and layout into popular CAD formats * Print PDF reports for the design, and share the design with colleagues Get more information about WEBENCH tools at www.ti.com/WEBENCH. 11.2 Documentation Support * * AN-2162 Simple Success With Conducted EMI From DC- DC Converters LMZ10501SIL and LMZ10500SIL SIMPLE SWITCHER (R) Nano Module Evaluation Board 11.3 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.4 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.5 Trademarks E2E is a trademark of Texas Instruments. WEBENCH is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.6 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.7 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 23 LMZ10500 SNVS723G - OCTOBER 2011 - REVISED JULY 2018 www.ti.com 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 12.1 Tape and Reel Information REEL DIMENSIONS TAPE DIMENSIONS K0 P1 B0 W Reel Diameter Cavity A0 B0 K0 W P1 A0 Dimension designed to accommodate the component width Dimension designed to accommodate the component length Dimension designed to accommodate the component thickness Overall width of the carrier tape Pitch between successive cavity centers Reel Width (W1) QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Sprocket Holes Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 User Direction of Feed Pocket Quadrants 24 Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W (mm) Pin1 Quadrant LMZ10500SILR uSiP SIL 8 3000 330.0 12.4 2.85 3.25 1.7 4.0 12.0 Q1 LMZ10500SILT uSiP SIL 8 250 178.0 13.2 2.85 3.25 1.7 4.0 12.0 Q1 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 LMZ10500 www.ti.com SNVS723G - OCTOBER 2011 - REVISED JULY 2018 TAPE AND REEL BOX DIMENSIONS Width (mm) W L H Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMZ10500SILR uSiP SIL 8 3000 383.0 353.0 58.0 LMZ10500SILT uSiP SIL 8 250 223.0 194.0 35.0 Submit Documentation Feedback Copyright (c) 2011-2018, Texas Instruments Incorporated Product Folder Links: LMZ10500 25 PACKAGE OUTLINE SIL0008G uSiP - 1.5mm max height SCALE 5. 000 MICRO SYSTEM IN PACKAGE 2.7 2.5 B (2) 3.1 2.9 (1.6) A INDUCTOR SUBSTRATE 1.5 MAX C 0.08 C 0.45 0.37 8X 0.1 (0.7) 0.7 0.5 4X (0.15) 0.4 8X 0.2 C A B 8X (0.7) 8X (0.4) 5 4 (2.35) 2X 3X (0.65) 4X (0.15) 2.25 0.1 1.95 1 (45 X0.15) PIN 1 ID 8 6X 0.65 (0.05) ALL AROUND 0.6 0.1 4224244/A 04/2018 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Pick and place nozzle 1.3 mm or smaller recommended. www.ti.com EXAMPLE BOARD LAYOUT SIL0008G uSiP - 1.5mm max height MICRO SYSTEM IN PACKAGE (1.9) 2X ( 0.2) VIA (0.6) 8 1 6X (0.65) SYMM (1.95) (2.25) (0.41) 4 5 SYMM 8X (0.3) SEE DETAILS 8X (0.6) LAND PATTERN EXAMPLE 1:1 RATIO WITH PACKAGE SOLDER PADS SCALE: 20X 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND SOLDERMASK OPENING METAL EDGE EXPOSED METAL SOLDER MASK OPENING EXPOSED METAL NON SOLDER MASK DEFINED METAL SOLDER MASK DEFINED SOLDER MASK DETAILS NOT TO SCALE 4224244/A 04/2018 NOTES: (continued) 4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271). www.ti.com EXAMPLE STENCIL DESIGN SIL0008G uSiP - 1.5mm max height MICRO SYSTEM IN PACKAGE (1.9) (0.6) 3X (0.62) 6X (0.65) 8 1 (0.816) SYMM (1.95) 4 8X (0.3) 5 SYMM 2X METAL 8X (0.6) SOLDER PASTE EXAMPLE BASED ON 0.125 MM THICK STENCIL 82% PRINTED SOLDER COVERAGE BY AREA SCALE: 20X 4224244/A 04/2018 NOTES: (continued) 5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. www.ti.com PACKAGE OPTION ADDENDUM www.ti.com 31-Aug-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMZ10500SILR ACTIVE uSiP SIL 8 3000 Green (RoHS & no Sb/Br) NiAu Level-3-260C-168 HR -40 to 125 TXN5000EC (500, DH) 9821 0500 0500 9821 DH LMZ10500SILT ACTIVE uSiP SIL 8 250 Green (RoHS & no Sb/Br) NiAu Level-3-260C-168 HR -40 to 125 TXN5000EC (500, DH) 9821 0500 0500 9821 DH (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 31-Aug-2018 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LMZ10500EVAL/NOPB LMZ10500SH/NOPB LMZ10500SHX/NOPB LMZ10500SHE/NOPB LMZ10500SILR LMZ10500SILT