SN74LS74A Dual D-Type Positive Edge-Triggered Flip-Flop The SN74LS74A dual edge-triggered flip-flop utilizes Schottky TTL circuitry to produce high speed D-type flip-flops. Each flip-flop has individual clear and set inputs, and also complementary Q and Q outputs. Information at input D is transferred to the Q output on the positive-going edge of the clock pulse. Clock triggering occurs at a voltage level of the clock pulse and is not directly related to the transition time of the positive-going pulse. When the clock input is at either the HIGH or the LOW level, the D input signal has no effect. http://onsemi.com LOW POWER SCHOTTKY MODE SELECT - TRUTH TABLE INPUTS OUTPUTS OPERATING MODE Set Reset (Clear) *Undetermined Load "1" (Set) Load "0" (Reset) * SD SD D Q Q L H L H H H L L H H X X X h l H L H H L L H H L H 14 1 PLASTIC N SUFFIX CASE 646 Both outputs will be HIGH while both SD and CD are LOW, but the output states are unpredictable if SD and CD go HIGH simultaneously. If the levels at the set and clear are near VIL maximum then we cannot guarantee to meet the minimum level for VOH. H, h = HIGH Voltage Level 14 L, I = LOW Voltage Level 1 X = Don't Care l, h (q) = Lower case letters indicate the state of the referenced input SOIC D SUFFIX CASE 751A i, h (q) = (or output) one set-up time prior to the HIGH to LOW clock transition. ORDERING INFORMATION GUARANTEED OPERATING RANGES Symbol VCC Parameter Supply Voltage Min Typ Max Unit Device Package Shipping 4.75 5.0 5.25 V SN74LS74AN 14 Pin DIP 2000 Units/Box 0 25 70 C SN74LS74AD 14 Pin 2500/Tape & Reel TA Operating Ambient Temperature Range IOH Output Current - High - 0.4 mA IOL Output Current - Low 8.0 mA Semiconductor Components Industries, LLC, 1999 December, 1999 - Rev. 6 1 Publication Order Number: SN74LS74A/D SN74LS74A LOGIC DIAGRAM (Each Flip-Flop) SET (SD) 4 (10) Q 5 (9) CLEAR (CD) 1 (13) CLOCK 3 (11) Q 6 (8) D 2 (12) LOGIC SYMBOL 4 10 2 D SD Q 3 CP CD Q 5 12 D SD Q 11 CP 6 CD Q 1 13 VCC = PIN 14 GND = PIN 7 http://onsemi.com 2 9 8 SN74LS74A DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage VOH Output HIGH Voltage VOL O Output LOW Voltage IIH Min Typ Max Unit 2.0 0.8 - 0.65 2.7 - 1.5 3.5 Output Short Circuit Current (Note 1) ICC Power Supply Current V Guaranteed Input LOW Voltage for All Inputs V VCC = MIN, IIN = - 18 mA V VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table VCC = VCC MIN, VIN = VIL or VIH per Truth Table V IOL = 4.0 mA 0.35 0.5 V IOL = 8.0 mA 20 40 A VCC = MAX, VIN = 2.7 V mA VCC = MAX, VIN = 7.0 V - 0.4 - 0.8 mA VCC = MAX, VIN = 0.4 V -100 mA VCC = MAX 8.0 mA VCC = MAX 0.1 0.2 IOS Guaranteed Input HIGH Voltage for All Inputs 0.4 Data, Clock Set, Clear Input LOW Current Data, Clock Set, Clear V 0.25 Input High Current Data, Clock Set, Clear IIL Test Conditions - 20 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V) Limits Symbol Parameter fMAX Maximum Clock Frequency tPLH tPHL Clock Clear Clock, Clear, Set to Output Min Typ 25 33 Max Unit MHz 13 25 ns 25 40 ns Max Unit Test Conditions Figure 1 Figure 1 VCC = 5.0 50V CL = 15 pF F AC SETUP REQUIREMENTS (TA = 25C) Limits Symbol Parameter Min Typ Test Conditions tW (H) Clock 25 ns Figure 1 tW (L) Clear, Set 25 ns Figure 2 Data Setup Time -- HIGH Data Setup Time -- LOW 20 ns ts 20 ns th Hold Time 5.0 ns Figure 1 http://onsemi.com 3 Figure 1 VCC = 5.0 V SN74LS74A AC WAVEFORMS 1.3 V D* 1.3 V th(H) th(L) ts(L) ts(H) tW(H) tW(L) 1.3 V 1.3 V CP tPHL Q 1 fMAX tPLH 1.3 V 1.3 V tPHL tPLH 1.3 V 1.3 V Q *The shaded areas indicate when the input is permitted to change for predictable output performance. Figure 1. Clock to Output Delays, Data Set-Up and Hold Times, Clock Pulse Width tW SET 1.3 V 1.3 V tW CLEAR Q 1.3 V tPLH tPHL 1.3 V 1.3 V tPHL Q 1.3 V tPLH 1.3 V 1.3 V Figure 2. Set and Clear to Output Delays, Set and Clear Pulse Widths http://onsemi.com 4 SN74LS74A PACKAGE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE M 14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B A F L N C -T- SEATING PLANE J K H G D 14 PL 0.13 (0.005) M M http://onsemi.com 5 DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10_ 0.38 1.01 SN74LS74A PACKAGE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 8 -B- 1 P 7 PL 0.25 (0.010) 7 G M B M R X 45 _ C F -T- SEATING PLANE D 14 PL 0.25 (0.010) M T B J M K S A S http://onsemi.com 6 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 SN74LS74A Notes http://onsemi.com 7 SN74LS74A ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800-4422-3781 Email: ONlit-asia@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 2:30pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 2:30pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 1:30pm to 5:00pm UK Time) Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5487-8345 Email: r14153@onsemi.com Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 SN74LS74A/D