ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com HIGH SPEED QUAD DIGITAL ISOLATORS Check for Samples: ISO7240CF, ISO7240C, ISO7240M, ISO7241C, ISO7241M, ISO7242C, ISO7242M FEATURES 1 * * * * * * * Selectable Failsafe Output (ISO7240CF) 25 and 150-Mbps Signaling Rate Options - Low Channel-to-Channel Output Skew; 1 ns Max - Low Pulse-Width Distortion (PWD); 2 ns Max - Low Jitter Content; 1 ns Typ at 150 Mbps Typical 25-Year Life at Rated Working Voltage (see application note SLLA197 and Figure 17) 4000-Vpeak VIOTM, 560-Vpeak VIORM per IEC 60747-5-2 (VDE 0884, Rev 2) UL 1577 , IEC 61010-1, IEC 60950-1 and CSA Approved * * 4 kV ESD Protection Operates With 2.8-V (ISO7241C), 3.3-V or 5-V Supplies High Electromagnetic Immunity (see application report SLLA181) -40C to 125C Operating Range APPLICATIONS * * * * Industrial Fieldbus Computer Peripheral Interface Servo Control Interface Data Acquisition DESCRIPTION The ISO7240, ISO7241 and ISO7242 are quad-channel digital isolators with multiple channel configurations and output enable functions. These devices have logic input and output buffers separated by TI's silicon dioxide (SiO2) isolation barrier. Used in conjunction with isolated power supplies, these devices block high voltage, isolate grounds, and prevent noise currents from entering the local ground and interfering with or damaging sensitive circuitry. The ISO7240 has all four channels in the same direction while the ISO7241 has three channels the same direction and one channel in opposition. The ISO7242 has two channels in each direction. The C option devices have TTL input thresholds and a noise-filter at the input that prevents transient pulses from being passed to the output of the device. The M option devices have CMOS Vcc/2 input thresholds and do not have the input noise-filter or the additional propagation delay. The ISO7240CF has an input disable function on pin 7, and a selectable high or low failsafe-output function with the CTRL pin (pin 10). The failsafe-output is a logic high when a logic-high is placed on the CTRL pin or it is left unconnected. If a logic-low signal is applied to the CTRL pin, the failsafe-output becomes a logic-low output state. The ISO7240CF input disable function prevents data from being passed across the isolation barrier to the output. When the inputs are disabled, the outputs are set by the CTRL pin. These devices may be powered from 2.8-V (ISO7241C only), 3.3-V or 5-V supplies on either side in any combination. Note that the signal input pins are 5-V tolerant regardless of the voltage supply level being used. These devices are characterized for operation over the ambient temperature range of -40C to 125C. VCC1 GND1 INA INB INC IND DISABLE GND1 ISO7240CF 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 ISO7240 VCC2 VCC1 GND2 GND1 OUTA INA INB OUTB INC OUTC OUTD IND CTRL NC GND2 GND1 1 2 3 4 5 6 7 8 ISO7241 16 15 14 13 12 11 10 9 VCC2 GND2 OUTA OUTB OUTC OUTD EN GND2 VCC1 GND1 INA INB INC OUTD EN1 GND1 1 2 3 4 5 6 7 8 ISO7242 16 15 14 13 12 11 10 9 VCC2 GND2 OUTA OUTB OUTC IND EN2 GND2 VCC1 GND1 INA INB OUTC OUTD EN1 GND1 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC2 GND2 OUTA OUTB INC IND EN2 GND2 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Table 1. Device Function Table ISO724x INPUT VCC (1) OUTPUT VCC (1) INPUT (IN) OUTPUT ENABLE (EN) OUTPUT (OUT) H H or Open H L H or Open L X L Z PU PU Open H or Open H PD PU X H or Open H PD PU X L Z PU = Powered Up; PD = Powered Down ; X = Irrelevant; H = High Level; L = Low Level Table 2. ISO7240CF Function Table VCC1 VCC2 DATA INPUT (IN) DISABLE INPUT (DISABLE) FAILSAFE CONTROL INPUT (CTRL) DATA OUTPUT (OUT) PU PU H L or Open X H PU PU L L or Open X L X PU X H H or Open H X PU X H L L PD PU X X H or Open H PD PU X X L L AVAILABLE OPTIONS PRODUCT SIGNALING RATE INPUT THRESHOLD CHANNEL CONFIGURATION MARKED AS ISO7240C 25 Mbps ~1.5 V (TTL) (CMOS compatible) ISO7240CF 25 Mbps ~1.5 V (TTL) (CMOS compatible) ISO7240M 150 Mbps Vcc/2 (CMOS) ISO7240M ISO7241C 25 Mbps ~1.5 V (TTL) (CMOS compatible) ISO7241C ISO7241M 150 Mbps Vcc/2 (CMOS) ISO7241M ISO7242C 25 Mbps ~1.5 V (TTL) (CMOS compatible) ISO7242C ISO7240C 4/0 ISO7240CF 3/1 2/2 ISO7242M (1) 2 150 Mbps Vcc/2 (CMOS) ISO7242M ORDERING NUMBER (1) ISO7240CDW (rail) ISO7240CDWR (reel) ISO7240CFDW (rail) ISO7240CFDWR (reel) ISO7240MDW (rail) ISO7240MDWR (reel) ISO7241CDW (rail) ISO7241CDWR (reel) ISO7241MDW (rail) ISO7241MDWR (reel) ISO7242CDW (rail) ISO7242CDWR (reel) ISO7242MDW (rail) ISO7242MDWR (reel) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) VALUE UNIT VCC Supply voltage (2), VCC1, VCC2 -0.5 to 6 V VI Voltage at IN, OUT, EN, DISABLE, CTRL -0.5 to 6 V IO Output current 15 mA ESD Electrostatic discharge TJ Maximum junction temperature (1) (2) Human Body Model JEDEC Standard 22, Test Method A114-C.01 Field-Induced-Charged Device Model JEDEC Standard 22, Test Method C101 Machine Model ANSI/ESDS5.2-1996 4 kV 1 All pins 200 V 170 C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to network ground terminal and are peak voltage values. RECOMMENDED OPERATING CONDITIONS MIN ISO7240C/CF, ISO7242C, ISO724xM, Supply voltage (1), VCC1, VCC2 VCC ISO7241C IOH High-level output current IOL Low-level output current 3.15 5.5 2.8 5.5 ISO724xC 40 ISO724xM 6.67 5 ISO724xC 0 30 (2) 25 ISO724xM 0 200 (2) 150 1/tui Signaling rate VIH High-level input voltage (IN) VIL Low-level input voltage (IN) VIH High-level input voltage (IN, DISABLE, CTRL, EN) VIL Low-level input voltage (IN, DISABLE, CTRL, EN) TJ Junction temperature H External magnetic field-strength immunity per IEC 61000-4-8 and IEC 61000-4-9 certification ISO724xM ISO724xC UNIT V mA 4 Input pulse width (2) MAX -4 tui (1) TYP mA ns Mbps 0.7 VCC VCC V 0 0.3 VCC V 2 VCC V 0 0.8 V 150 C 1000 A/m For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For the 3.3-V operation, VCC1 or VCC2 is specified from 3.15 V to 3.6 V. For the 2.8-V operation (ISO7241C-only), VCC1 or VCC2 is specified at 2.8 V. Typical value at room temperature and well-regulated power supply. IEC 60747-5-2 INSULATION CHARACTERISTICS (1) over recommended operating conditions (unless otherwise noted) PARAMETER VIORM VPR TEST CONDITIONS Maximum working insulation voltage Input to output test voltage SPECIFICATIONS UNIT 560 V After Input/Output Safety Test Subgroup 2/3 VPR = VIORM x 1.2, t = 10 s, Partial discharge < 5 pC 672 V Method a, VPR = VIORM x 1.6, Type and sample test with t = 10 s, Partial discharge < 5 pC 896 V Method b1, VPR = VIORM x 1.875, 100 % Production test with t = 1 s, Partial discharge < 5 pC 1050 V VIOTM Transient overvoltage t = 60 s 4000 V RS Insulation resistance VIO = 500 V at TS >109 Pollution degree (1) 2 Climatic Classification 40/125/21 Copyright (c) 2007-2012, Texas Instruments Incorporated 3 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS: VCC1 and VCC2 at 5-V (1) OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT ISO7240C/M ICC1 ISO7241C/M ISO7242C/M ISO7240C/M ICC2 ISO7241C/M ISO7242C/M Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V- 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V- 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal 1 3 7 10.5 All channels, no load, EN1 at 3 V, EN2 at 3 V 6.5 11 12 18 All channels, no load, EN1 at 3 V, EN2 at 3 V 10 16 15 24 All channels, no load, EN at 3 V 15 22 17 25 All channels, no load, EN1 at 3 V, EN2 at 3 V 13 20 18 28 All channels, no load, EN1 at 3 V, EN2 at 3 V 10 16 15 24 All channels, no load, EN at 3 V mA mA mA mA mA mA ELECTRICAL CHARACTERISTICS IOFF Sleep mode output current VOH High-level output voltage VOL Low-level output voltage EN at 0 V, Single channel VCC-0.8 IOH = -20 A, See Figure 1 VCC-0.1 0.4 IOL = 20 A, See Figure 1 0.1 150 IIH High-level input current IIL Low-level input current CI Input capacitance to ground IN at VCC, VI = 0.4 sin (4E6t) CMTI Common-mode transient immunity VI = VCC or 0 V, See Figure 5 4 V IOL = 4 mA, See Figure 1 VI(HYS) Input voltage hysteresis (1) A 0 IOH = -4 mA, See Figure 1 IN from 0 V to VCC mV 10 -10 25 V A 2 pF 50 kV/s For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com SWITCHING CHARACTERISTICS: VCC1 and VCC2 at 5-V OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP Propagation delay PWD Pulse-width distortion (1) |tPHL - tPLH| tPLH, tPHL Propagation delay PWD Pulse-width distortion (1) |tPHL - tPLH| tsk(pp) Part-to-part skew tsk(o) Channel-to-channel output skew tr Output signal rise time tf Output signal fall time tPHZ Propagation delay, high-level-to-high-impedance output 15 20 tPZH Propagation delay, high-impedance-to-high-level output 15 20 tPLZ Propagation delay, low-level-to-high-impedance output 15 20 tPZL Propagation delay, high-impedance-to-low-level output 15 20 tfs Failsafe output delay time from input power loss See Figure 3 12 s twake Wake time from input disable See Figure 4 15 s Peak-to-peak eye-pattern jitter 150 Mbps NRZ data input, Same polarity input on all channels, See Figure 6 1 ns (1) (2) (3) ISO724xC See Figure 1 ISO724xM 42 UNIT tPLH, tPHL tjit(pp) 18 MAX 2.5 10 23 1 ISO724xC (2) 8 ISO724xM (3) 0 ISO724xC 3 2 ISO724xM 0 See Figure 1 ISO724xM 2 See Figure 2 1 2 ns ns ns ns ns 2 ns Also referred to as pulse skew. tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same supply voltages, at the same temperature, and have identical packages and test circuits. tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the same direction while driving identical specified loads. Copyright (c) 2007-2012, Texas Instruments Incorporated 5 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS: VCC1 at 5-V, VCC2 at 3.3-V (1) OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT ISO7240C/M ICC1 ISO7241C/M ISO7242C/M ISO7240C/M ICC2 ISO7241C/M ISO7242C/M Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal 1 3 7 10.5 All channels, no load, EN1 at 3 V, EN2 at 3 V 6.5 11 12 18 All channels, no load, EN1 at 3 V, EN2 at 3 V 10 16 15 24 9.5 15 10.5 17 8 13 11.5 18 6 10 9 14 All channels, no load, EN at 3 V All channels, no load, EN at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V mA mA mA mA mA mA ELECTRICAL CHARACTERISTICS IOFF Sleep mode output current VOH High-level output voltage EN at 0 V, Single channel IOH = -4 mA, See Figure 1 ISO7240 VCC-0.4 ISO724x (5-V side) VCC-0.8 IOH = -20 A, See Figure 1 0.4 IOL = 20 A, See Figure 1 0.1 Low-level output voltage VI(HYS) Input voltage hysteresis IIH High-level input current IIL Low-level input current CI Input capacitance to ground IN at VCC, VI = 0.4 sin (4E6t) CMTI Common-mode transient immunity VI = VCC or 0 V, See Figure 5 6 V VCC-0.1 IOL = 4 mA, See Figure 1 VOL (1) A 0 150 IN from 0 V to VCC mV 10 -10 25 V A 2 pF 50 kV/s For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For the 3.3-V operation, VCC1 or VCC2 is specified from 3.15 V to 3.6 V. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com SWITCHING CHARACTERISTICS: VCC1 at 5-V, VCC2 at 3.3-V OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS TYP Propagation delay Pulse-width distortion (1) |tPHL - tPLH| tPLH, tPHL Propagation delay PWD Pulse-width distortion(1) |tPHL - tPLH| tsk(pp) Part-to-part skew tsk(o) Channel-to-channel output skew tr Output signal rise time tf Output signal fall time tPHZ Propagation delay, high-level-to-high-impedance output 15 20 tPZH Propagation delay, high-impedance-to-high-level output 15 20 tPLZ Propagation delay, low-level-to-high-impedance output 15 20 tPZL Propagation delay, high-impedance-to-low-level output 15 20 tfs Failsafe output delay time from input power loss See Figure 3 18 s twake Wake time from input disable See Figure 4 15 s Peak-to-peak eye-pattern jitter 150 Mbps PRBS NRZ data input, Same polarity input on all channels, See Figure 6 1 ns (1) (2) (3) 50 UNIT PWD tjit(pp) 20 MAX tPLH, tPHL ISO724xC See Figure 1 MIN 3 ISO724xM 12 29 1 ISO724xC (2) 10 ISO724xM (3) 0 ISO724xC 5 3 ISO724xM 0 See Figure 1 ISO724xM 2 See Figure 2 1 2 ns ns ns ns ns 2 ns Also known as pulse skew tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same supply voltages, at the same temperature, and have identical packages and test circuits. tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the same direction while driving identical specified loads. Copyright (c) 2007-2012, Texas Instruments Incorporated 7 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS: VCC1 at 3.3-V, VCC2 at 5-V (1) OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 0.5 1 3 5 4 7 6.5 11 All channels, no load, EN1 at 3 V, EN2 at 3 V 6 10 9 14 All channels, no load, EN at 3 V 15 22 17 25 All channels, no load, EN1 at 3 V, EN2 at 3 V 13 20 18 28 All channels, no load, EN1 at 3 V, EN2 at 3 V 10 16 15 24 UNIT SUPPLY CURRENT ISO7240C/M ISO7241C/M ICC1 ISO724C/M ISO7240C/M ISO7241C/M ICC2 ISO7242C/M Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal All channels, no load, EN at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V mA mA mA mA mA mA ELECTRICAL CHARACTERISTICS IOFF Sleep mode output current VOH High-level output voltage EN at 0 V, Single channel IOH = -4 mA, See Figure 1 IOH = -20 A, See Figure 1 ISO724x (5-V side) VCC - 0.8 V VCC - 0.1 0.4 IOL = 20 A, See Figure 1 0.1 Low-level output voltage VI(HYS) Input voltage hysteresis IIH High-level input current IIL Low-level input current CI Input capacitance to ground IN at VCC, VI = 0.4 sin (4E6t) CMTI Common-mode transient immunity VI = VCC or 0 V, See Figure 5 8 VCC - 0.4 IOL = 4 mA, See Figure 1 VOL (1) A 0 ISO7240 150 IN from 0 V to VCC mV 10 -10 25 V A 2 pF 50 kV/s For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For the 3.3-V operation, VCC1 or VCC2 is specified from 3.15 V to 3.6 V. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com SWITCHING CHARACTERISTICS: VCC1 at 3.3-V and VCC2 at 5-V OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 22 51 UNIT tPLH, tPHL Propagation delay PWD Pulse-width distortion (1) |tPHL - tPLH| tPLH, tPHL Propagation delay PWD Pulse-width distortion(1) |tPHL - tPLH| tsk(pp) Part-to-part skew tsk(o) Channel-to-channel output skew tr Output signal rise time tf Output signal fall time tPHZ Propagation delay, high-level-to-high-impedance output 15 20 tPZH Propagation delay, high-impedance-to-high-level output 15 20 tPLZ Propagation delay, low-level-to-high-impedance output 15 20 tPZL Propagation delay, high-impedance-to-low-level output 15 20 tfs Failsafe output delay time from input power loss See Figure 3 12 s twake Wake time from input disable See Figure 4 15 s Peak-to-peak eye-pattern jitter 150 Mbps NRZ data input, Same polarity input on all channels, See Figure 6 1 ns tjit(pp) (1) (2) (3) ISO724xC See Figure 1 ISO724xM 3 12 30 1 ISO724xC (2) 10 ISO724xM (3) 0 ISO724xC 5 2.5 ISO724xM 0 See Figure 1 ISO724xM 2 See Figure 2 1 2 ns ns ns ns ns 2 ns Also known as pulse skew tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same supply voltages, at the same temperature, and have identical packages and test circuits. tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the same direction while driving identical specified loads. Copyright (c) 2007-2012, Texas Instruments Incorporated 9 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS: VCC1 and VCC2 at 3.3 V (1) OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT ISO7240C/M ISO7241C/M ICC1 ISO7242C/M ISO7240C/M ISO7241C/M ICC2 ISO7242C/M Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal All channels, no load, EN at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V All channels, no load, EN at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V All channels, no load, EN1 at 3 V, EN2 at 3 V 0.5 1 3 5 4 7 6.5 11 6 10 9 14 9.5 15 10.5 17 8 13 11.5 18 6 10 9 14 mA mA mA mA ELECTRICAL CHARACTERISTICS IOFF Sleep mode output current VOH High-level output voltage VOL Low-level output voltage EN at 0 V, single channel VCC-0.4 IOH = -20 A, See Figure 1 VCC-0.1 0.4 IOL = 20 A, See Figure 1 0.1 150 IIH High-level input current IIL Low-level input current CI Input capacitance to ground IN at VCC, VI = 0.4 sin (4E6t) CMTI Common-mode transient immunity VI = VCC or 0 V, See Figure 5 10 V IOL = 4 mA, See Figure 1 VI(HYS) Input voltage hysteresis (1) A 0 IOH = -4 mA, See Figure 1 IN from 0 V or VCC mV 10 -10 25 V A 2 pF 50 kV/s For the 3.3-V operation, VCC1 or VCC2 is specified from 3.15 V to 3.6 V. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com SWITCHING CHARACTERISTICS: VCC1 and VCC2 at 3.3-V OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 25 56 UNIT tPLH, tPHL Propagation delay PWD Pulse-width distortion |tPHL - tPLH| (1) tPLH, tPHL Propagation delay PWD Pulse-width distortion |tPHL - tPLH| (1) tsk(pp) Part-to-part skew tsk(o) Channel-to-channel output skew tr Output signal rise time tf Output signal fall time tPHZ Propagation delay, high-level-to-high-impedance output 15 20 tPZH Propagation delay, high-impedance-to-high-level output 15 20 tPLZ Propagation delay, low-level-to-high-impedance output 15 20 tPZL Propagation delay, high-impedance-to-low-level output 15 20 tfs Failsafe output delay time from input power loss See Figure 3 18 s twake Wake time from input disable See Figure 4 15 s Peak-to-peak eye-pattern jitter 150 Mbps PRBS NRZ data input, same polarity input on all channels, See Figure 6 1 ns tjit(pp) (1) (2) (3) ISO724xC See Figure 1 ISO724xM 4 12 34 1 ISO724xC (2) 10 ISO724xM (3) 0 ISO724xC 5 3.5 ISO724xM 0 See Figure 1 ISO724xM 2 See Figure 2 1 ns ns ns ns 2 ns 2 ns ns Also referred to as pulse skew. tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same supply voltages, at the same temperature, and have identical packages and test circuits. tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the same direction while driving identical specified loads. Copyright (c) 2007-2012, Texas Instruments Incorporated 11 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS: VCC1 and VCC2 at 2.8 V (ISO7241C only) (1) OPERATION over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT ICC1 ISO7241C ICC2 ISO7241C Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal Quiescent VI = VCC or 0 V 25 Mbps 12.5 MHz Input Clock Signal All channels, no load, EN1 at 3 V, EN2 at 3 V 3.9 6.8 6.2 10.5 All channels, no load, EN1 at 3 V, EN2 at 3 V 6.9 12 9.4 16 mA mA ELECTRICAL CHARACTERISTICS IOFF Sleep mode output current VOH High-level output voltage VOL Low-level output voltage EN1 at 0 V, single channel A 0 IOH = -4 mA, See Figure 1 VCC-0.6 IOH = -20 A, See Figure 1 VCC-0.1 V IOL = 4 mA, See Figure 1 0.6 IOL = 20 A, See Figure 1 0.1 VI(HYS) Input voltage hysteresis 150 IIH High-level input current IIL Low-level input current CI Input capacitance to ground IN at VCC, VI = 0.4 sin (4E6t) CMTI Common-mode transient immunity VI = VCC or 0 V, See Figure 5 IN from 0 V or VCC mV 10 -10 10 V A 2 pF 45 kV/s (1) For the 2.8-V operation, VCC1 or VCC2 is specified at 2.8-V. 2.8-V operation is only guaranteed for ISO7241C with production screening starting in January 2012. The first two digits of the Lot Trace Code (YMLLLLS) written on top of each device can be used to identify year and month of production respectively. 12 Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com SWITCHING CHARACTERISTICS: VCC1 and VCC2 at 2.8-V OPERATION (ISO7241C only) over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 25 70 UNIT tPLH, tPHL Propagation delay PWD Pulse-width distortion |tPHL - tPLH| (1) tsk(pp) Part-to-part skew tsk(o) Channel-to-channel output skew tr Output signal rise time tf Output signal fall time tPHZ Propagation delay, high-level-to-high-impedance output tPZH Propagation delay, high-impedance-to-high-level output tPLZ Propagation delay, low-level-to-high-impedance output tPZL Propagation delay, high-impedance-to-low-level output tfs Failsafe output delay time from input power loss See Figure 3 7 s twake Wake time from input disable See Figure 4 12 s (1) (2) (3) (2) (3) ISO7241C See Figure 1 5 ns ISO7241C 12 ns ISO7241C 5 ns See Figure 1 See Figure 2 2 ns 2 ns 15 25 15 25 15 25 15 25 ns Also referred to as pulse skew. tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same supply voltages, at the same temperature, and have identical packages and test circuits. tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the same direction while driving identical specified loads. Copyright (c) 2007-2012, Texas Instruments Incorporated 13 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com ISOLATION BARRIER PARAMETER MEASUREMENT INFORMATION IN Input Generator VI 50 W NOTE A VCC VI VCC/2 VCC/2 OUT 0V tPHL tPLH CL NOTE B VO VO VOH 90% 50% 50% 10% tr VOL tf A. The input pulse is supplied by a generator having the following characteristics: PRR 50 kHz, 50% duty cycle, tr 3 ns, tf 3 ns, ZO = 50. B. CL = 15 pF and includes instrumentation and fixture capacitance within 20%. Figure 1. Switching Characteristic Test Circuit and Voltage Waveforms Vcc VCC ISOLATION BARRIER 0V RL = 1 kW 1% IN Input Generator VI OUT EN VCC/2 VI t PZL VO VO CL VCC/2 0V t PLZ VCC 0.5 V 50% NOTE B 50 W VOL 3V ISOLATION BARRIER NOTE A IN Input Generator VI OUT VO VCC VCC/2 VI VCC/2 0V EN 50 W t PZH CL NOTE B RL = 1 kW 1% VO VOH 50% 0.5 V t PHZ 0V NOTE A A. The input pulse is supplied by a generator having the following characteristics: PRR 50 kHz, 50% duty cycle, tr 3 ns, tf 3 ns, ZO = 50. B. CL = 15 pF and includes instrumentation and fixture capacitance within 20%. Figure 2. Enable/Disable Propagation Delay Time Test Circuit and Waveform 14 Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) VI 0V or VCC1 A. IN VCC ISOLATION BARRIER VCC 2.7 V VI OUT 0V VO tfs VOH CL NOTE A VO 50% fs low VOL CL = 15 pF and includes instrumentation and fixture capacitance within 20%. 3V IN DISABLE ISOLATION BARRIER Figure 3. Failsafe Delay Time Test Circuit and Voltage Waveforms OUT VCC VO VI 0V CTRL t wake VCC CL Input VI Generator 0V 50 % ( Note B) 50 W VO IN 0V DISABLE ISOLATION BARRIER ( Note A) 0V VCC OUT VO VI VCC/2 0V t wake CTRL VCC2 CL Input Generator VCC/2 VI 3V 50 W (Note B ) VO ( Note A ) 50 % 0V NOTE: Which ever test yields the longest time is used in this data sheet A. The input pulse is supplied by a generator having the following characteristics: PRR 50 kHz, 50% duty cycle, tr 3 ns, tf 3 ns, ZO = 50. B. CL = 15 pF and includes instrumentation and fixture capacitance within 20%. Figure 4. Wake Time From Input Disable Test Circuit and Voltage Waveforms Copyright (c) 2007-2012, Texas Instruments Incorporated 15 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) VCC1 VCC2 IN S1 C = 0.1 mF 1% ISOLATION BARRIER C = 0.1 mF 1% OUT Pass-fail criteria: Output must remain stable VOH or VOL NOTE B GND1 GND2 VCM A. CL = 15 pF and includes instrumentation and fixture capacitance within 20%. B. The input pulse is supplied by a generator having the following characteristics: PRR 50 kHz, 50% duty cycle, tr 3 ns, tf 3 ns, ZO = 50. Figure 5. Common-Mode Transient Immunity Test Circuit and Voltage Waveform VCC DUT Tektronix HFS9009 IN OUT 0V Tektronix 784D PATTERN GENERATOR VCC/2 Jitter NOTE: PRBS bit pattern run length is 216 - 1. Transition time is 800 ps. NRZ data input has no more than five consecutive 1s or 0s. Figure 6. Peak-to-Peak Eye-Pattern Jitter Test Circuit and Voltage Waveform DEVICE INFORMATION PACKAGE CHARACTERISTICS PARAMETER L(I01) TEST CONDITIONS MIN TYP MAX UNIT Minimum air gap (Clearance) Shortest terminal-to-terminal distance through air 8.34 mm L(I02) Minimum external tracking (Creepage) Shortest terminal-to-terminal distance across the package surface 8.1 mm CTI Tracking resistance (comparative tracking index) DIN IEC 60112/VDE 0303 Part 1 400 V Minimum Internal Gap (Internal Clearance) Distance through the insulation 0.008 mm RIO Isolation resistance Input to output, VIO = 500 V, all pins on each side of the barrier tied together creating a two-terminal device CIO Barrier capacitance Input to output CI Input capacitance to ground >1012 VI = 0.4 sin (4E6t) 2 pF VI = 0.4 sin (4E6t) 2 pF IEC 60664-1 RATINGS TABLE PARAMETER Basic isolation group Installation classification 16 TEST CONDITIONS Material group SPECIFICATION II Rated mains voltage 150 VRMS I-IV Rated mains voltage 300 VRMS I-III Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com spacer REGULATORY INFORMATION VDE CSA UL Certified according to IEC 60747-5-2 Approved under CSA Component Acceptance Notice 5A Recognized under 1577 Component Recognition Program Basic Insulation Maximum Transient Overvoltage, 4000 VPK Maximum Surge Votlage, 4000 VPK Maximum Working Voltage, 560 VPK Basic insulation per CSA 60950-1-07 and IEC 60950-1 (2nd Ed), 395 VRMS maximum working voltage, 4000 VPK maximum isolation rating Single protection, 2500 VRMS (1) File Number: 40016131 File Number: 220991 File Number: E181974 (1) Production tested 3000 VRMS for 1 second in accordance with UL 1577. spacer DEVICE I/O SCHEMATICS Enable VCC Output Input VCC VCC VCC VCC VCC 1 MW 1 MW 500 W EN VCC IN 8W 500 W OUT 13 W ISO7240CF Input VCC VCC IN 500 W 1 MW Copyright (c) 2007-2012, Texas Instruments Incorporated 17 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com THERMAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS Low-K Thermal Resistance JA Junction-to-air JB Junction-to-Board Thermal Resistance JC Junction-to-Case Thermal Resistance PD (1) MIN TYP MAX (1) 168 High-K Thermal Resistance C/W 96.1 61 C/W 48 C/W VCC1 = VCC2 = 5.5 V, TJ = 150C, CL = 15 pF, Input a 50% duty cycle square wave Device Power Dissipation UNIT 220 mW Tested in accordance with the Low-K or High-K thermal metric definitions of EIA/JESD51-3 for leaded surface mount packages. spacer TYPICAL CHARACTERISTIC CURVES ISO7240C/M RMS SUPPLY CURRENT vs SIGNALING RATE ISO7241C/M RMS SUPPLY CURRENT vs SIGNALING RATE 45 45 TA = 25C, Load = 15 pF, All Channels 40 ICC - Supply Current - mA/RMS ICC - Supply Current - mA/RMS 40 35 5-V ICC2 30 3.3-V ICC2 25 20 5-V ICC1 15 10 5 35 5-V ICC2 30 20 3.3-V ICC2 15 50 75 100 Signaling Rate - Mbps 125 5 0 0 150 100 ISO7242C/M RMS SUPPLY CURRENT vs SIGNALING RATE PROPAGATION DELAY vs FREE-AIR TEMPERATURE 125 150 45 TA = 25C, Load = 15 pF, All Channels 40 C 3.3-V tpLH, tpHL 35 30 Propagation Delay - ns ICC - Supply Current - mA/RMS 75 Figure 8. 5-V ICC1,ICC2 25 20 15 3.3-V ICC1,ICC2 C 5-V tpLH, tpHL 30 25 M 3.3-V tpLH, tpHL 20 15 M 5-V tpLH, tpHL 10 10 5 5 TA = 25C, Load = 15 pF, All Channels 0 25 50 75 100 Signaling Rate - Mbps Figure 9. 18 50 Figure 7. 35 0 0 25 Signaling Rate - Mbps 45 40 3.3-V ICC1 10 0 25 5-V ICC1 25 3.3-V ICC1 0 TA = 25C, Load = 15 pF, All Channels 125 150 -40 -25 -10 5 80 65 35 20 50 TA - Free-Air Temperature - C 95 110 125 Figure 10. Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTIC CURVES (continued) INPUT VOLTAGE THRESHOLD vs FREE-AIR TEMPERATURE VCC UNDERVOLTAGE THRESHOLD vs FREE-AIR TEMPERATURE 1.4 3 5 V Vth+ 1.3 2.9 VCC - Undervoltage Threshold - V Input Voltage Threshold - V 1.35 3.3 V Vth+ 1.25 1.2 Air Flow at 7 cf/m, Low_K Board 1.15 5 V Vth1.1 1.05 1 -40 3.3 V Vth-25 -10 VCC Rising 2.7 2.6 2.5 VCC Falling 2.4 2.3 2.2 2.1 5 20 35 50 65 80 TA - Free-Air Temperature - C 95 110 2 -40 125 -25 -10 5 20 35 50 65 80 95 110 125 TA - Free-Air Temperature - C Figure 11. Figure 12. HIGH-LEVEL OUTPUT CURRENT vs HIGH-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT CURRENT vs LOW-LEVEL OUTPUT VOLTAGE 50 50 VCC = 5 V Load = 15 pF, TA = 25C Load = 15 pF, TA = 25C 45 40 IO - Output Current - mA 40 IO - Output Current - mA 2.8 VCC = 3.3 V 30 20 35 VCC = 3.3 V 30 25 VCC = 5 V 20 15 10 10 5 0 0 0 2 4 VO - Output Voltage - V Figure 13. Copyright (c) 2007-2012, Texas Instruments Incorporated 6 0 1 2 3 VO - Output Voltage - V 4 5 Figure 14. 19 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com APPLICATION INFORMATION 2 mm max. from VCC1 VCC1 2 mm max. from VCC2 VCC2 0.1 mF 0.1 mF 1 16 2 15 IN A 3 14 OUT A IN B 4 13 OUT B IN C 5 12 OUT C IN D 6 11 GND1 GND2 NC 7 10 8 9 OUT D EN GND2 GND1 ISO7240x Figure 15. Typical ISO7240x Application Circuit 2 mm max. from VCC1 VCC1 2 mm max. from VCC2 VCC2 0.1 mF 0.1 mF 1 16 2 15 IN A 3 14 OUT A IN B 4 13 OUT B IN C 5 12 OUT C 6 11 GND1 IN D GND2 DISABLE OUT D CTRL 7 10 8 9 GND2 GND1 ISO7240CF Figure 16. Typical ISO7240CF Failsafe-Low Application Circuit 20 Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 www.ti.com LIFE EXPECTANCY vs. WORKING VOLTAGE WORKING LIFE -- YEARS 100 VIORM at 560-V 28 Years 10 0 120 250 500 750 880 1000 WORKING VOLTAGE (VIORM) -- V Figure 17. Time-Dependant Dielectric Breakdown Testing Results REVISION HISTORY Changes from Original (September 2007) to Revision A Page * Deleted Product Preview note .............................................................................................................................................. 2 * Changed VCC Supply Voltage in the ROC Table From: 3.6 To: 3.45 ................................................................................... 3 * Changed VCC Supply Voltage in the ROC Table From: 3 To: 3.15 ...................................................................................... 3 * Changed TBDs to actual values. .......................................................................................................................................... 4 * Changed CI - typ value From: 1 To: 2 .................................................................................................................................. 4 * Changed Propagation delay max From: 22 To: 23 .............................................................................................................. 5 * Changed CI - typ value From: 1 To: 2 .................................................................................................................................. 6 * Changed Propagation delay max From: 46 To: 50 .............................................................................................................. 7 * Changed Propagation delay max From: 28 To: 29 .............................................................................................................. 7 * Changed ISO724xA/C max value From: 2.5 To: 3 ............................................................................................................... 7 * Changed CI - typ value From: 1 To: 2 .................................................................................................................................. 8 * Changed Propagation delay max From: 26 To: 30 .............................................................................................................. 9 * Changed typ value From: 1 To: 2 ....................................................................................................................................... 10 * Changed Propagation delay max From: 32 To: 34 ............................................................................................................ 11 * Changed ISO724xA/C max value From: 3 To: 3.5 ............................................................................................................. 11 * Changed CIO - typ value From: 1 To: 2 .............................................................................................................................. 16 * Changed CI - typ value From: 1 To: 2 ................................................................................................................................ 16 * Changed the REGULATORY INFORMATION Table ......................................................................................................... 17 * Changed Figure 7, Figure 8, and Figure 10. Added Figure 9. ........................................................................................... 18 Changes from Revision A (December 2007) to Revision B * Page Changed VCC Supply Voltage in the ROC Table From: 3.45 To: 3.6 ................................................................................... 3 Changes from Revision B (August 2008) to Revision C Page * Deleted Min = 4.5 V and max = 5.5 V for Supply Voltage of the ROC Table. ..................................................................... 3 * Changed VCC Supply Voltage in the ROC Table From: 3.6 To: 5.5 ..................................................................................... 3 Copyright (c) 2007-2012, Texas Instruments Incorporated 21 ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 Changes from Revision C (April 2008) to Revision D www.ti.com Page * Changed Feature Bullet 4000-Vpeak Isolation ........................................................................................................................ 1 * Added tsk(pp) Part-to-part skew .............................................................................................................................................. 5 * Added tsk(pp) Part-to-part skew .............................................................................................................................................. 7 * Added tsk(pp) Part-to-part skew .............................................................................................................................................. 9 * Added tsk(pp) Part-to-part skew ............................................................................................................................................ 11 * Changed Typical ISO724x Application Circuit Figure 15 .................................................................................................... 20 Changes from Revision D (April 2008) to Revision E Page * Added Table Note (1): For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. .............................................. 3 * Added Table Note (1): For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V ............................................... 6 * Added Table Note (1): For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V ............................................... 8 * Added Table Note (1): For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V ............................................. 10 Changes from Revision E (May 2008) to Revision F Page * Changed Title From: QUAD DIGITAL ISOLATORS To: HIGH SPEED QUAD DIGITAL ISOLATORS ............................... 1 * Deleted ISO724xA devices. See SLLS905 for the ISO7240A, ISO7241A, and ISO7242A. ................................................ 1 * Changed Feature Low Jitter Content - From: 1, 25, and 150-Mbps Signaling Rate Options To: 25, and 150-Mbps Signaling Rate Options ......................................................................................................................................................... 1 * Added tsk(pp) footnote. ............................................................................................................................................................ 5 * Added tsk(o) footnote. ............................................................................................................................................................. 5 * Added tsk(pp) footnote. .......................................................................................................................................................... 11 * Added tsk(o) footnote. ........................................................................................................................................................... 11 Changes from Revision F (May 2008) to Revision G * Page Changed the PACKAGE CHARACTERISTICS table, line , L(IO1) MIN value from7.7mm to 8.34mm ................................ 16 Changes from Revision G (July 2008) to Revision H Page * Added Device number ISO7240CF. ..................................................................................................................................... 1 * Added Features Bullet: Selectable Failsafe Output (ISO7240CF) ....................................................................................... 1 * Changed description paragraph 4 text. ................................................................................................................................. 1 * Added for device number ISO7240CF. ................................................................................................................................. 2 * Changed VI in the Abs Max Table From: Voltage at IN, OUT, EN To: Voltage at IN, OUT, EN, DISABLE, CTRL ............. 3 * Added twake, Wake time from input disable ........................................................................................................................... 5 * Added twake, Wake time from input disable ........................................................................................................................... 7 * Added twake, Wake time from input disable ........................................................................................................................... 9 * Added twake, Wake time from input disable ......................................................................................................................... 11 Changes from Revision H (October 2008) to Revision I * 22 Page Added information to the Features bullet to include CSA and IEC 60950-1 certification ..................................................... 1 Copyright (c) 2007-2012, Texas Instruments Incorporated ISO7240CF, ISO7240C, ISO7240M ISO7241C, ISO7241M ISO7242C, ISO7242M www.ti.com Changes from Revision I (December 2008) to Revision J SLLS868N - SEPTEMBER 2007 - REVISED JANUARY 2012 Page * Changed ICC1 for Quiescent and 1Mbps From: 10mA To: 11mA ......................................................................................... 4 * Changed ICC1 for Quiescent and 1Mbps From: 10mA To: 11mA ......................................................................................... 6 Changes from Revision J (April 2009) to Revision K * Page Changed the Input circuit in the DEVICE I/O SCHEMATICS illustration ............................................................................ 17 Changes from Revision K (Decemberl 2009) to Revision L Page * Added the IEC 60747-5-2 INSULATION CHARACTERISTIC table ..................................................................................... 3 * Added CTI - Tracking resistance (comparative tracking index to the PACKAGE CHARACTERISTICS table .................. 16 * Added the IEC 60664-1 RATINGS TABLE ......................................................................................................................... 16 Changes from Revision L (January 2010) to Revision M Page * Changed Figure 1, Figure 3, and Figure 4 ......................................................................................................................... 14 * Changed the CSA File Number From: 1698195 To: 220991 ............................................................................................. 17 Changes from Revision M (January 2011) to Revision N Page * Changed Feature From: 4000-Vpeak Isolation, 560-Vpeak VIORM To: 4000-Vpeak VIOTM, 560-Vpeak VIORM per IEC 60747-5-2 (VDE 0884, Rev 2) .............................................................................................................................................. 1 * Changed Feature From: Operates 3.3-V or 5-V Supplies To: Operates With 2.8-V (ISO7241C), 3.3-V or 5-V Supplies ................................................................................................................................................................................ 1 * Added device options to VCC in the RECOMMENDED OPERATING CONDITIONS table .................................................. 3 * Changed Table Note (1) ....................................................................................................................................................... 3 * Changed ICC1 and ICC2 test conditions in the VCC1 and VCC2 at 5-V table ............................................................................. 4 * Changed Table Note (1) ....................................................................................................................................................... 4 * Changed ICC1 and ICC2 test conditions in the VCC1 at 5-V, VCC2 at 3.3-V table ...................................................................... 6 * Changed Table Note (1) ....................................................................................................................................................... 6 * Changed ICC1 and ICC2 test conditions in the VCC1 at 3.3-V, VCC2 at 5-V table ...................................................................... 8 * Changed Table Note (1) ....................................................................................................................................................... 8 * Changed ICC1 and ICC2 test conditions in the VCC1 and VCC2 at 3.3 V table ........................................................................ 10 * Changed Table Note (1) ..................................................................................................................................................... 10 * Added ELECTRICAL and Switching CHARACTERISTICS tables forVCC1 and VCC2 at 2.8V (ISO722xC-only) ................. 12 * Changed the CTI MIN value From: 175 V To:400 V ...................................................................................................... 16 * Changed the REGULATORY INFORMATION Table ......................................................................................................... 17 * Changed Figure 12 From VCC1 Failsafe Threshold To: VCC Undervoltage Threshold ........................................................ 19 Copyright (c) 2007-2012, Texas Instruments Incorporated 23 PACKAGE OPTION ADDENDUM www.ti.com 23-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) ISO7240CDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CFDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CFDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CFDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240CFDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240MDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240MDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240MDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7240MDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241CDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241CDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241CDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241CDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241MDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 23-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) ISO7241MDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241MDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7241MDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242CDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242CDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242CDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242CDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242MDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242MDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242MDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR ISO7242MDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 23-Aug-2012 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF ISO7240CF, ISO7241C, ISO7242C : * Automotive: ISO7240CF-Q1, ISO7241C-Q1, ISO7242C-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 30-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant ISO7240CDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 ISO7240CFDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 ISO7241CDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 ISO7241MDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 ISO7242CDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 ISO7242MDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 30-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ISO7240CDWR SOIC DW 16 2000 533.4 186.0 36.0 ISO7240CFDWR SOIC DW 16 2000 533.4 186.0 36.0 ISO7241CDWR SOIC DW 16 2000 367.0 367.0 38.0 ISO7241MDWR SOIC DW 16 2000 533.4 186.0 36.0 ISO7242CDWR SOIC DW 16 2000 367.0 367.0 38.0 ISO7242MDWR SOIC DW 16 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated