LM339DTBR2G - ON Semiconductor

November, 2010 − Rev. 19

Publication Order Number:

LM339/D

LM339, LM239, LM2901,

LM2901V, NCV2901,

MC3302

Single Supply Quad

Comparators

These comparators are designed for use in level detection, low−level

sensing and memory applications in consumer, automotive, and

industrial electronic applications.

Features

•Single or Split Supply Operation

•Low Input Bias Current: 25 nA (Typ)

•Low Input Offset Current: ±5.0 nA (Typ)

•Low Input Offset Voltage

•Input Common Mode Voltage Range to GND

•Low Output Saturation Voltage: 130 mV (Typ) @ 4.0 mA

•TTL and CMOS Compatible

•ESD Clamps on the Inputs Increase Reliability without Affecting

Device Operation

•NCV Prefix for Automotive and Other Applications Requiring Site

and Control Changes

•These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS

Compliant

PDIP−14

N, P SUFFIX

CASE 646

SOIC−14

D SUFFIX

CASE 751A

PIN CONNECTIONS

)

Output 2

- Input 1

Output 1

Output 3

Output 4

+ Input 1

- Input 2

+ Input 2

+ Input 4

- Input 4

+ Input 3

- Input 3

VCC GND

)

(Top View)

See detailed ordering and shipping information in the package

dimensions section on page 7 of this data sheet.

ORDERING INFORMATION

See general marking information in the device marking

section on page 8 of this data sheet.

DEVICE MARKING INFORMATION

http://onsemi.com

TSSOP−14

DTB SUFFIX

CASE 948G

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

MAXIMUM RATINGS

Rating Symbol Value Unit

Power Supply Voltage

LM239/LM339/LM2901, V

MC3302

VCC

+36 or ±18

+30 or ±15

Vdc

Input Differential Voltage Range

LM239/LM339/LM2901, V

MC3302

VIDR

Vdc

Input Common Mode Voltage Range VICMR −0.3 to VCC Vdc

Output Short Circuit to Ground (Note 1) ISC Continuous

Power Dissipation @ TA = 25°C

Plastic Package

Derate above 25°C

1/RqJA

1.0

8.0

mW/°C

Junction Temperature TJ150 °C

Operating Ambient Temperature Range

LM239

MC3302

LM2901

LM2901V, NCV2901

LM339

−25 to +85

−40 to +85

−40 to +105

−40 to +125

0 to +70

°C

Storage Temperature Range Tstg −65 to +150 °C

ESD Protection at any Pin (Note 2)

Human Body Model

Machine Model

VESD

1500

200

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC. Output short circuits to VCC can cause excessive

heating and eventual destruction.

2. VESD rating for NCV/SC devices is: Human Body Model − 2000 V; Machine Model − 200 V.

Figure 1. Circuit Schematic

VCC + Input - Input Output

GND

NOTE: Diagram shown is for 1 comparator.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

ELECTRICAL CHARACTERISTICS (VCC = +5.0 Vdc, TA = +25°C, unless otherwise noted)

Characteristic Symbol

LM239/339

LM2901/2901V/

NCV2901 MC3302

Unit

Min Typ Max Min Typ Max Min Typ Max

Input Offset Voltage (Note 4) VIO −±2.0 ±5.0 −±2.0 ±7.0 −±3.0 ±20 mVdc

Input Bias Current (Notes 4, 5) IIB −25 250 −25 250 −25 500 nA

(Output in Analog Range)

Input Offset Current (Note 4) IIO −±5.0 ±50 −±5.0 ±50 −±3.0 ±100 nA

Input Common Mode Voltage Range VICMR 0−VCC

−1.5

0−VCC

−1.5

0−VCC

−1.5

Supply Current ICC mA

RL = ∞ (For All Comparators) −0.8 2.0 −0.8 2.0 −0.8 2.0

RL = ∞, VCC = 30 Vdc −1.0 2.5 −1.0 2.5 −1.0 2.5

Voltage Gain AVOL 50 200 −25 100 −25 100 −V/mV

RL ≥ 15 kW, VCC = 15 Vdc

Large Signal Response Time − − 300 − − 300 − − 300 −ns

VI = TTL Logic Swing,

Vref = 1.4 Vdc, VRL = 5.0 Vdc,

RL = 5.1 kW

Response Time (Note 6) − − 1.3 − − 1.3 − − 1.3 −ms

VRL = 5.0 Vdc, RL = 5.1 kW

Output Sink Current ISink 6.0 16 −6.0 16 −6.0 16 −mA

VI (−) ≥ +1.0 Vdc, VI(+) = 0,

VO ≤ 1.5 Vdc

Saturation Voltage Vsat −130 400 −130 400 −130 500 mV

VI(−) ≥ +1.0 Vdc, VI(+) = 0,

Isink ≤ 4.0 mA

Output Leakage Current IOL −0.1 − − 0.1 − − 0.1 −nA

VI(+) ≥ +1.0 Vdc, VI(−) = 0,

VO = +5.0 Vdc

3. (LM239) Tlow = −25°C, Thigh = +85°

(LM339) Tlow = 0°C, Thigh = +70°C

(MC3302) Tlow = −40°C, Thigh = +85°C

(LM2901) Tlow = −40°C, Thigh = +105°

(LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C

NCV2901 is qualified for automotive use.

4. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 W 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range

(0 Vdc to VCC −1.5 Vdc).

5. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state.

6. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

PERFORMANCE CHARACTERISTICS (VCC = +5.0 Vdc, TA = Tlow to Thigh [Note 7])

Characteristic Symbol

LM239/339

LM2901/2901V/

NCV2901 MC3302

Unit

Min Typ Max Min Typ Max Min Typ Max

Input Offset Voltage (Note 8) VIO − − ±9.0 − − ±15 − − ±40 mVdc

Input Bias Current (Notes 8, 9) IIB − − 400 − − 500 − − 1000 nA

(Output in Analog Range)

Input Offset Current (Note 8) IIO − − ±150 − − ±200 − − ±300 nA

Input Common Mode Voltage Range VICMR 0−VCC

−2.0

0−VCC

−2.0

0−VCC

−2.0

Saturation Voltage Vsat − − 700 − − 700 − − 700 mV

VI(−) ≥ +1.0 Vdc, VI(+) = 0,

Isink ≤ 4.0 mA

Output Leakage Current IOL − − 1.0 − − 1.0 − − 1.0 mA

VI(+) ≥ +1.0 Vdc, VI(−) = 0,

VO = 30 Vdc

Differential Input Voltage VID − − VCC − − VCC − − VCC Vdc

All VI ≥ 0 Vdc

7. (LM239) Tlow = −25°C, Thigh = +85°

(LM339) Tlow = 0°C, Thigh = +70°C

(MC3302) Tlow = −40°C, Thigh = +85°C

(LM2901) Tlow = −40°C, Thigh = +105°

(LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C

NCV2901 is qualified for automotive use.

8. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 W 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range

(0 Vdc to VCC −1.5 Vdc).

9. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state.

10.The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.

Figure 2. Inverting Comparator

with Hysteresis

Figure 3. Noninverting Comparator

with Hysteresis

Vref = VCC R1

Rref + R1

R2 [ R1 / / Rref

Amount of Hysteresis VH

VH = R2

R2 + R3 [(VO(max) - VO(min)]

Vref [VCC R1

Rref + R1

R3 ] R1 / / Rref / / R2

VH = R1 / / Rref

R1/ / Rref + R2 [VO(max) - VO(min)]

R2 ơ Rref / / R1

+ VCC

Vin

Vref

+ VCC

Vin Vref

Rref

+VO

10k R1

10 k

1.0 M

10 k

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

Figure 4. Normalized Input Offset Voltage Figure 5. Input Bias Current

Figure 6. Output Sink Current versus

Output Saturation Voltage

Typical

haracteristics

(VCC = 15 Vdc, TA = +25°C (each comparator) unless otherwise noted.)

TA, AMBIENT TEMPERATURE (°C) VCC, POWER SUPPLY VOLTAGE (Vdc)

NORMALIZED OFFSET VOLTAGE

Vsat, OUTPUT SATURATION VOLTAGE (mV)

I , OUTPUT CURRENT (mA)

1.40

1.20

1.00

0.80

0.60 -50 -25 0 25 50 75 100 125

6.0

0 4.0 8.0 12 16 20 24 28 32

TA = -55° C

TA = +25° C

TA = +125°C

I INPUT BIAS CURRENT (nA)

IB,

8.0

7.0

6.0

5.0

4.0

3.0

2.0

1.0

100 200 300 400 500

TA = +25° C

TA = -55°C

TA = +125°C

Figure 7. Driving Logic Figure 8. Squarewave Oscillator

Logic Device

VCC

(V)

CMOS

TTL

1/4 MC14001

1/4 MC7400

+15

+5.0

100

RS = Source Resistance

R1 ] RS

T1 = T2 = 0.69 RC

f [7.2

C(mF)

R2 = R3 = R4

R1 [ R2 // R3 // R4

VCC

Vin

Vref

VCC ≥ 4.0 V

VCC

330 k

R4 330 k

100 k 10 k

T1 T2

VCC

RSRL

330 k

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

APPLICATIONS INFORMATION

These quad comparators feature high gain, wide

bandwidth characteristics. This gives the device oscillation

tendencies if the outputs are capacitively coupled to the

inputs via stray capacitance. This oscillation manifests itself

during output transitions (VOL to VOH). To alleviate this

situation input resistors < 10 kW should be used. The

addition of positive feedback (< 10 mV) is also

recommended. It is good design practice to ground all

unused input pins.

Differential input voltages may be larger than supply

voltages without damaging the comparator’s inputs.

Voltages more negative than −300 mV should not be used.

Figure 9. Zero Crossing Detector

(Single Supply)

Figure 10. Zero Crossing Detector

(Split Supplies)

Vin(min) ≈0.4 V peak for 1% phase distortion (Dq).

D1 prevents input from going negative by more than 0.6 V.

R1 + R2 = R3

R3 ≤R5 for small error in zero crossing

Vin

10 k

8.2 k

6.8 k

15 k

+15 V

VCC

10 k

Vin

VEE

Vin Vin(min)

VCC

VEE Dq

)

10 M

220 k

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

ORDERING INFORMATION

Device Package Shipping†

LM239DG SOIC−14 55 Units/Tube

LM239DR2G SOIC−14 2500 / Tape & Reel

LM239DTBR2G TSSOP−14

LM239NG PDIP−14 25 Units/Rail

LM339DG SOIC−14 55 Units/Tube

LM339DR2G SOIC−14 2500 / Tape & Reel

LM339DTBR2G TSSOP−14

LM339NG PDIP−14 25 Units/Rail

LM2901DG SOIC−14 55 Units/Rail

LM2901DR2G SOIC−14 2500 / Tape & Reel

LM2901DTBR2G TSSOP−14

LM2901NG PDIP−14 25 Units/Rail

LM2901VDG SOIC−14 55 Units/Tube

LM2901VDR2G SOIC−14 2500 / Tape & Reel

LM2901VDTBR2G TSSOP−14

LM2901VNG PDIP−14 25 Units/Rail

NCV2901DR2G SOIC−14 2500 / Tape & Reel

NCV2901DTBR2G TSSOP−14

NCV2901CTR Bare Die 6000 / Tape & Reel

MC3302DG SOIC−14 55 Units/Tube

MC3302DR2G SOIC−14 2500 / Tape & Reel

MC3302DTBR2G TSSOP−14

MC3302PG PDIP−14 25 Units/Rail

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

SOIC−14

D SUFFIX

CASE 751A

PDIP−14

N, P SUFFIX

CASE 646

MARKING DIAGRAMS

*This marking diagram also applies to NCV2901.

239

ALYW G

TSSOP−14

DTB SUFFIX

CASE 948G

339

ALYW G

2901

ALYW G

2901

ALYW G

3302

ALYW G

LM339DG

AWLYWW

LM239DG

AWLYWW

LM2901DG

AWLYWW

LM2901VDG

AWLYWW

MC3302DG

AWLYWW

A = Assembly Location

WL, L = Wafer Lot

YY, Y = Year

WW, W = Work Week

G or G= Pb−Free Package

LM339N

AWLYYWWG

LM239N

AWLYYWWG

LM2901N

AWLYYWWG

LM2901VN

AWLYYWWG

MC3302P

AWLYYWWG

141414

111

(Note: Microdot may be in either location)

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

PACKAGE DIMENSIONS

PDIP−14

CASE 646−06

ISSUE P

14 8

ADIM MIN MAX MIN MAX

MILLIMETERSINCHES

A0.715 0.770 18.16 19.56

B0.240 0.260 6.10 6.60

C0.145 0.185 3.69 4.69

D0.015 0.021 0.38 0.53

F0.040 0.070 1.02 1.78

G0.100 BSC 2.54 BSC

H0.052 0.095 1.32 2.41

J0.008 0.015 0.20 0.38

K0.115 0.135 2.92 3.43

M−−− 10 −−− 10

N0.015 0.039 0.38 1.01

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN

FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

HG D

SEATING

PLANE

−T−

14 PL

0.13 (0.005)

0.290 0.310 7.37 7.87

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

PACKAGE DIMENSIONS

SOIC−14

CASE 751A−03

ISSUE H

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE

DAMBAR PROTRUSION. ALLOWABLE

DAMBAR PROTRUSION SHALL BE 0.127

(0.005) TOTAL IN EXCESS OF THE D

DIMENSION AT MAXIMUM MATERIAL

CONDITION.

−A−

−B−

P7 PL

14 8

0.25 (0.010) B M

0.25 (0.010) A S

−T−

RX 45

SEATING

PLANE D14 PL K

_DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A8.55 8.75 0.337 0.344

B3.80 4.00 0.150 0.157

C1.35 1.75 0.054 0.068

D0.35 0.49 0.014 0.019

F0.40 1.25 0.016 0.049

G1.27 BSC 0.050 BSC

J0.19 0.25 0.008 0.009

K0.10 0.25 0.004 0.009

M0 7 0 7

P5.80 6.20 0.228 0.244

R0.25 0.50 0.010 0.019

__ __

7.04

14X

0.58

14X

1.52

1.27

DIMENSIONS: MILLIMETERS

PITCH

SOLDERING FOOTPRINT*

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

PACKAGE DIMENSIONS

TSSOP−14

CASE 948G−01

ISSUE B

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A4.90 5.10 0.193 0.200

B4.30 4.50 0.169 0.177

C−−− 1.20 −−− 0.047

D0.05 0.15 0.002 0.006

F0.50 0.75 0.020 0.030

G0.65 BSC 0.026 BSC

H0.50 0.60 0.020 0.024

J0.09 0.20 0.004 0.008

J1 0.09 0.16 0.004 0.006

K0.19 0.30 0.007 0.012

K1 0.19 0.25 0.007 0.010

L6.40 BSC 0.252 BSC

M0 8 0 8

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSION A DOES NOT INCLUDE MOLD

FLASH, PROTRUSIONS OR GATE BURRS.

MOLD FLASH OR GATE BURRS SHALL NOT

EXCEED 0.15 (0.006) PER SIDE.

4. DIMENSION B DOES NOT INCLUDE

INTERLEAD FLASH OR PROTRUSION.

INTERLEAD FLASH OR PROTRUSION SHALL

NOT EXCEED 0.25 (0.010) PER SIDE.

5. DIMENSION K DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.08 (0.003) TOTAL

IN EXCESS OF THE K DIMENSION AT

MAXIMUM MATERIAL CONDITION.

6. TERMINAL NUMBERS ARE SHOWN FOR

REFERENCE ONLY.

7. DIMENSION A AND B ARE TO BE

DETERMINED AT DATUM PLANE −W−.

____

U0.15 (0.006) T

2X L/2

0.10 (0.004) V S

L−U−

SEATING

PLANE

0.10 (0.004)

−T−

ÇÇÇ

SECTION N−N

DETAIL E

JJ1

ÉÉÉ

DETAIL E

−W−

0.25 (0.010)

PIN 1

IDENT.

U0.15 (0.006) T

−V−

14X REFK

7.06

14X

0.36 14X

1.26

0.65

DIMENSIONS: MILLIMETERS

PITCH

SOLDERING FOOTPRINT*

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

LM339, LM239, LM2901, LM2901V, NCV2901, MC3302

http://onsemi.com

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5773−3850

LM339/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative