R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 CONTENTS 1 Part Numbering 2 Selection Guide of Trimmer Potentiometers 3 1 2 3 4 5 6 7 SMD Open Type 2mm Size PVZ2/PVA2 Series 4 PVZ2/PVA2 Series Notice 8 SMD Open Type 3mm Size PVZ3 Series 10 PVZ3 Series Notice 14 SMD Sealed Type 3mm Size PVG3 Series 16 PVG3 Series Notice 19 SMD Sealed Type 4mm Size PVM4 Series 21 PVM4 Series Notice 23 SMD Sealed Type Multi-turn PVG5 Series 26 PVG5 Series Notice 29 Lead Sealed Type Single-turn PV32 Series 31 PV32 Series Notice 34 Lead Sealed Type Multi-turn PV12/PV37/PV36 Series 36 PV12/PV37/PV36 Series Notice 43 SMD Open Type (PVZ2/A2/Z3)/SMD Sealed Type (PVM4A_C01 Series) Specifications and Test Methods 45 SMD Sealed Type (PVG3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods 46 Packaging 49 Recommended Adjustment Tools/Qualified Standards 52 s 4HE 2O(3 COMPLIANCE MEANS THAT WE JUDGE FROM %5 $IRECTIVE %5 THE PRODUCTS DO NOT CONTAIN LEAD CADMIUM MERCURY HEXAVALENT CHROMIUM 0"" AND 0"$% EXCEPT EXEMPTIONS STATED IN %5 $IRECTIVE %5 ANNEX AND IMPURITIES EXISTING IN THE NATURAL WORLD s 4HIS STATEMENT DOES NOT INSURE THE COMPLIANCE OF ANY OF THE LISTED PARTS WITH ANY LAWS OR LEGAL IMPERATIVES DEVELOPED BY ANY %5 MEMBERS INDIVIDUALLY WITH REGARDS TO THE 2O(3 $IRECTIVE 2 3 4 5 6 7 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 o Part Numbering Trimmer Potentiometers (Part Number) PV Z3 A 103 q w e r C01 R00 t y rTotal Resistance qProduct ID Product ID PV Trimmer Potentiometers wSeries Expressed by three figures. The unit is ohm. The first and second figures are significant digits, and the third figure expresses the number of zeros that follow the two figures. Ex.) Code eAdjustment Direction /Lead Type Series Code Adjustment Direction/ Lead Type Z2 SMD Open 2mm Size Carbon Resistive Element A Top R Rear A2 SMD Open 2mm Size Code Z3 2 SMD Open 3mm Size Carbon Resistive Element Total Resistance 100 10 102 1000 104 100000 (=100k) tIndividual Specification A Top Series Code A Top PVA2 A01 Standard Type G Top H Top C04 Standard Type (High-heat Resistance Type/Ultra-thin Type) C01 Standard Type (High-heat Resistance Type/Top Adjustment) F01 High Characteristic Carbon Type (only PVZ3G) E01 High-heat Resistance Type (for Rear Adjustment) K Rear A Top, J-hook G3 SMD Sealed 3mm Size G Top, Gull-wing M4 SMD Sealed 4mm Size A Top G5 SMD Sealed 5mm Square 11 turns A Top H Side 32 Lead Sealed 6mm Round Single turn H Top, Triangle N Side, Triangle 12 Lead Sealed 7mm Round 4 turns P Top, Triangle T Side, Triangle 36 Lead Sealed 10mm Square 25 turns W 37 Lead Sealed 6mm Square 12 turns X Side, Triangle PVZ2 PVZ3 Individual Specification Code C01 Standard Type D01 High-reliability Type PV32/PV12 A01 Standard Type Top, Inline PVG3/ PV36/PV37 C01 Standard Type X Side, Inline PVG5 C03 Standard Type W Top, Triangle PVM4 yPackaging Code Packaging B00 Bulk R00 Reel R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Selection Guide of Trimmer Potentiometers Mounting Method Surface Mount PCB Insertion Sealed Construction Construction? Adjustment? Open Sealed Top Side Carbon Resistive Element Cermet Resistive Element Cermet Resistive Element Cermet Resistive Element 2mm size Single Turn 3mm size Single Turn 6mm size Single Turn 6mm size Single Turn PVZ2A_C04 PVG3A Low Profile (0.85mm max.) for Automatic Adjustment with Rotational Stop PVZ2R PVG3G Rear Adjustment Low Profile with Smaller Foot print (0.9mm max.) 3mm size Single Turn with Rotational Stop PV32H PV32N with Rotational Stop with Rotational Stop 7mm size 4 Turns 4mm size Single Turn PV12P PVZ3A for Automatic Adjustment Top Adjustment Low Profile (1.25mm max.) PVZ3H Top Adjustment PVZ3K PV12T PVM4 6mm size 12 Turns PVZ3G 7mm size 4 Turns 6mm size 12 Turns 5mm size 11 Turns PVG5 PV37W 10mm size 25 Turns PV36W PV37X 10mm size 25 Turns PV36X Rear Adjustment Cermet Resistive Element 2mm size Single Turn PVA2 for Automatic Adjustment (0.9mm max.) 3 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers 1 SMD Open Type 2mm Size PVZ2/PVA2 Series PVZ2 Series c Features 2.1 Part Number 6. DVC 7. Digital camera 8. Portable audio, etc. 9. RKE 10. E-Book 0.5 4 1 1.3 2.2 2.70.3 0.5 0.450.1 Soldering Part 0.4 #1 #3 0.55 0.7 0.55 #2 #1 CLOCKWISE PVZ2A #3 1 Driver Plate Rotation Area: Please do not place any components more than 0.5mm in height within this area. (Tolerance:in0.2 mm) +0.10 2.1 0.8 0.8 -0.15 0.450.10 (0.6) #2 4.8 1.3 2.2 2.4 Dia. 1 Soldering Part #1 #3 0.65 0.6 0.65 PVZ2R 1: Driver Plate Rotation Area #2 #1 CLOCKWISE #3 ( Tolerancein: 0.2 mm ) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVZ2p471C04 0.05(50C) 1(24010) Endless 470ohm30% 500 PVZ2p102C04 0.05(50C) 1(24010) Endless 1k ohm30% 500 PVZ2p222C04 0.05(50C) 1(24010) Endless 2.2k ohm30% 500 PVZ2p472C04 0.05(50C) 1(24010) Endless 4.7k ohm30% 500 PVZ2p103C04 0.05(50C) 1(24010) Endless 10k ohm30% 500 PVZ2p223C04 0.05(50C) 1(24010) Endless 22k ohm30% 500 PVZ2p473C04 0.05(50C) 1(24010) Endless 47k ohm30% 500 PVZ2p104C04 0.05(50C) 1(24010) Endless 100k ohm30% 500 PVZ2p224C04 0.05(50C) 1(24010) Endless 220k ohm30% 500 PVZ2p474C04 0.05(50C) 1(24010) Endless 470k ohm30% 500 PVZ2p105C04 0.05(50C) 1(24010) Endless 1M ohm30% 500 Operating Temperature Range: -25 to 85 C Soldering Method: Reflow/Soldering Iron 4 0.5 2.4 Dia. 1 #2 c Applications 1. Pick-up module 2. LCD 3. Cellular phone 4. PHS 5. Pager 0.80.05 0.8 (0.6) 1. Ultra-small and thin external dimensions of 2.1(W)x2.7(L)x0.85 max. (T)mm. (Top adjustment type: PVZ2A_C04 Series) 2. Ultra-small and thin external dimensions of 2.1(W)x4.8(L)x0.9 max. (T)mm. (Rear adjustment type: PVZ2R_C04 Series) Compact PCB design is possible by smaller adjustment hole (3.0mm dia.) due to short wing length (4.8mm). 3. Au plated termination achieves a high-density PCB mounting. 4. Cross-shaped driver slot allows for in-process automatic adjustment and it provides superior adjustability. 5. Two-piece parts construction achieves low cost and excellent quality. 6. Special resin substrate allows high peak temperature for reflow soldering (PVZ2_Cxx Series). 7. PVZ2 series complies with RoHS directive. R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Construction Jul.23,2012 c Standard Land Pattern PVZ2A 1 PVZ2A 0.85 0.6 0.7 1.55 1.55 0.85 0.9 0.6 (Tolerance in: 0.1 mm) c Construction c Standard Land Pattern PVZ2R PVZ2R 0.9 0.6 #2-Terminal 2.5 Driver Plate 3.0 Dia. #1-Terminal Resistive Element #3-Terminal Resin Substrate 0.6 2.5 Wiper 0.7 0.6 0.7 ( Tolerancein: 0.1 mm ) c Characteristics Humidity Exposure Res. Change: +10, -2% High Temperature Exposure Res. Change: R< =50kohm***+2, -10% 50kohm<R***+2, -15% Humidity Load Life Res. Change: 10% Load Life Res. Change: R< =50kohm***+2, -10% 50kohm<R***+2, -15% Temperature Cycle Res. Change: 5% Rotational Life Res. Change: 10% (10 cycles) 5 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVA2 Series 0.8 0.4 1.3 0.5 2.4 Dia Resin 0.75 1.3 1. Ultra-small and thin external dimensions of 2.2(W)x2.75(L)x0.90 max.(T)mm. 2. For the terminal attachment method of construction that uses neither solder nor adhesives, good solderability and terminal attachment intensity are realized. 3. Because of multi-contact wiper structure, PVA2 has a stable characteristics (low noise). 4. PVA2 series does not use a solder, flux or cleaning solvent, so they are environmentally friendly products. 5. Heat resistance performance enables high temperature peak reflow soldering. 6. PVA2 series complies with RoHS directive. 0.80.1 2.2 #2 0.450.1 c Features 2.75 1 #1 #3 0.6 0.5 0.9 0.6 #2 (Wiper Contact) #1 #3 CLOCKWISE CIRCUIT (Tolerance:in0.2 mm) c Applications 1. Thin-model optical pick-up module 2. LCD module 3. Optical communication module 4. Small sensor module 5. Digital camera 6. Small telecommunications equipment, etc. 7. E-Book Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVA2A101A01 0.1(70C) 1(26010) Endless 100ohm25% 250 PVA2A221A01 0.1(70C) 1(26010) Endless 220ohm25% 250 PVA2A471A01 0.1(70C) 1(26010) Endless 470ohm25% 250 PVA2A102A01 0.1(70C) 1(26010) Endless 1k ohm25% 250 PVA2A222A01 0.1(70C) 1(26010) Endless 2.2k ohm25% 250 PVA2A472A01 0.1(70C) 1(26010) Endless 4.7k ohm25% 250 PVA2A103A01 0.1(70C) 1(26010) Endless 10k ohm25% 250 PVA2A223A01 0.1(70C) 1(26010) Endless 22k ohm25% 250 PVA2A473A01 0.1(70C) 1(26010) Endless 47k ohm25% 250 PVA2A104A01 0.1(70C) 1(26010) Endless 100k ohm25% 250 PVA2A224A01 0.1(70C) 1(26010) Endless 220k ohm25% 250 PVA2A474A01 0.1(70C) 1(26010) Endless 470k ohm25% 250 PVA2A105A01 0.1(70C) 1(26010) Endless 1M ohm25% 250 PVA2A225A01 0.1(70C) 1(26010) Endless 2.2M ohm25% 250 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Reflow/Soldering Iron 6 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Construction Jul.23,2012 c Standard Land Pattern 1 Driver Plate 1.55 Wiper #2-Terminal 1.70 0.90 #1-Terminal 0.85 1.1 Resistive Element 0.70 #3-Terminal Ceramic Substrate 1.90 ( Tolerancein: 0.1 mm ) c Characteristics Humidity Exposure Res. Change: 3% High Temperature Exposure Res. Change: 3% Humidity Load Life Res. Change: 3% Load Life Res. Change: 3% Temperature Cycle Res. Change: 3% Rotational Life Res. Change: 10% (10 cycles) 7 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVZ2/PVA2 Series Notice 1 c Notice (Operating and Storage Conditions) 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. 3. If the trimmer potentiometer is used in DC and high humidity conditions, please connect wiper (#2) for plus and resistive element (#1 or #3) for minus. (PVZ Series only) c Notice (Soldering and Mounting) 1. Soldering (1) Reflow soldering method and soldering iron are available. This product cannot be soldered using the flow soldering method (dipping). If you use the flow soldering method, the trimmer potentiometer may not function. (2) Use our standard land dimension. Excessive land area causes displacement due to the effect of the surface tension of the solder. Insufficient land area leads to insufficient soldering strength of the chip. (3) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer potentiometer may deviate from the specified characteristics. (4) Apply the appropriate amount of solder paste. The thickness of solder paste should be printed from 100 micro m to 150 micro m and the dimension of land pattern used should be Murata's standard land pattern at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals. (5) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. 2. Mounting (1) Do not apply excessive force, preferably 4.9N max. (Ref. 500gf) when the trimmer potentiometer is mounted to the PCB. (2) Do not warp and/or bend the PC board to protect trimmer potentiometer from breakage. (3) In chip placers, the recommended size of the cylindrical pick-up nozzle should be outer dimension 1.5-1.8mm dia. and inner dimension 1.3mm dia. 3. Cleaning (1) In case there is flux on the resistive element, clean sufficiently with cleaning solvents and completely remove all residual flux. (2) Isopropyl alcohol and ethyl alcohol are applicable solvents for cleaning. If you use any other types of solvents, please evaluate performance with your product. Continued on the following page. 8 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVZ2/PVA2 Series Notice 1 Continued from the preceding page. c Soldering Profile Reflow Soldering Profile 1. Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu) Temperature (C) T5 T3 T2 T4 T1 t2 Limit Profile t3 Standard Profile Time (s) t1 Standard Profile Pre-heating Limit Profile Peak Cycle of Temperature Reflow Time (t2) (T3) Heating Series Temp. (T1) Time (t1) Temp. (T2) C sec. C sec. C Time Pre-heating Temp. (T1) Time (t1) C sec. Peak Cycle of Temperature Reflow Time (t3) (T5) Heating Temp. (T4) C sec. C Time PVZ2 150 to 180 60 to 120 220 30 to 60 2453 2 150 to 180 60 to 120 220 30 to 60 260 2 PVA2 150 to 180 60 to 120 220 30 to 60 2453 2 150 to 180 60 to 120 220 30 to 60 260 +5/-0 2 2. Soldering profile for Eutectic solder (63Sn/37Pb) Temperature (C) (Limit profile: refer to 1) Standard Profile T3 Pre-heating t2 T1 Standard Profile PVZ2 PVA2 t1 Peak Cycle of Temperature Reflow Time (t2) (T3) Heating Series T2 Temp. (T1) Time (t1) Temp. (T2) C sec. C sec. C Time 150 60 to 120 183 30 230 1 time (s) Soldering Iron Standard Condition Series Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 PVZ2 PVA2 c Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in the driver slot. We recommend the screwdriver below. * Recommended screwdriver for manual adjustment Murata P/N: KMDR190 2. The screwdriver should be set in the products vertically, do not apply more than 4.9N (Ref. 500gf) of twist and stress after mounting onto PCB to prevent contact intermittence. If excessive force is applied, the trimmer potentiometer may not function. 3. Please use within the effective rotational angle. The trimmer potentiometer does not have a mechanical stop for over rotation. In cases out of effective rotational angle, the trimmer potentiometer may not function. 4. When using a lock paint to fix the slot position or cover the rotor, please evaluate performance with your product. Lock paint may cause corrosion or electrical contact problems. c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. 9 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers SMD Open Type 3mm Size PVZ3 Series PVZ3 Series c Features 1.15 Dia. 1.0 2.2 Dia. #2 0.1 max. 3.2 2.40.1 3.6 0.50.1 #1 1.0 #3 0.75 0.7 #2 #1 #3 CLOCKWISE 0.7 PVZ3A (Tolerance:in0.3 mm) 1.55 0.40 0.25 0.55 0.6 Soldering Part 3.1 0.40 PVZ3H 3.1 0.5 #2 6. CD-ROMs 7. Car stereos 8. TFT-LCD TV sets 9. Headphone stereos .2 o2 0.55 #1 1.2 #3 0 o3. 3.6 o1 .1 5 0.8 2.4 mm (Tolerance in: 0.3 ) 0.55 1.150.10 0.4 5 .7 R0 3.1 0.8 #2 R1 1.2 #3 0.55 #2 (Wiper Contact) 0.6 0.55 #1 3.6 2.10.1 .5 3.1 c Applications 0.75 1.850.1 0.250.1 3.0 Dia. 0.50.1 1. Excellent solderability characteristics are achieved via special plating techniques on each termination. 2. Specially designed substrate prevents wicking of flux onto the top of the part body. 3. Funnel shaped adjustment slot allows for in-process automatic adjustment. (PVZ3A/PVZ3H/PVZ3K Series) 4. High-heat resistance type is available (PVZ3A_C01/PVZ3K_E01). 5. Enlarged bottom termination enhances soldering strength while reducing the necessary land area required, promoting high-density PCB mounting (PVZ3A/PVZ3H/PVZ3G Series). 6. The standard position of the driver plate is adjusted at the center normally, but another position is also available. 7. This product meets PB-free standards. 8. Complies with RoHS directive. 1. Optical pick up 2. Cordless telephones 3. CD players 4. E-Book 5. Motor 3.1 #1 #3 CLOCKWISE CIRCUIT 0.55 PVZ3G (Tolerance:in0.3 mm) 2.1 1.850.1 3.1 0.250.1 3.2 #2 #3 #1 Soldering Part 1.15 Dia. 2.2 Dia. 3.0 Dia. 2.40.1 1.1 PVZ3K 0.85 0.9 0.85 10 0.50.1 5.4 4.4 2 #2 (Wiper Contact) #1 #3 CLOCKWISE CIRCUIT (Tolerance:in0.3 mm) R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Top Adjustment (H 1.85) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVZ3A221C01 0.1(50C) 1(23010) Endless 220ohm30% 500 PVZ3A471C01 0.1(50C) 1(23010) Endless 470ohm30% 500 PVZ3A102C01 0.1(50C) 1(23010) Endless 1k ohm30% 500 PVZ3A222C01 0.1(50C) 1(23010) Endless 2.2k ohm30% 500 PVZ3A472C01 0.1(50C) 1(23010) Endless 4.7k ohm30% 500 PVZ3A103C01 0.1(50C) 1(23010) Endless 10k ohm30% 500 PVZ3A223C01 0.1(50C) 1(23010) Endless 22k ohm30% 500 PVZ3A473C01 0.1(50C) 1(23010) Endless 47k ohm30% 500 PVZ3A104C01 0.1(50C) 1(23010) Endless 100k ohm30% 500 PVZ3A224C01 0.1(50C) 1(23010) Endless 220k ohm30% 500 PVZ3A474C01 0.1(50C) 1(23010) Endless 470k ohm30% 500 PVZ3A105C01 0.1(50C) 1(23010) Endless 1M ohm30% 500 PVZ3A225C01 0.1(50C) 1(23010) Endless 2.2M ohm30% 500 Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVZ3H221C01 0.1(50C) 1(23010) Endless 220ohm30% 500 PVZ3H471C01 0.1(50C) 1(23010) Endless 470ohm30% 500 PVZ3H102C01 0.1(50C) 1(23010) Endless 1k ohm30% 500 PVZ3H222C01 0.1(50C) 1(23010) Endless 2.2k ohm30% 500 PVZ3H472C01 0.1(50C) 1(23010) Endless 4.7k ohm30% 500 PVZ3H103C01 0.1(50C) 1(23010) Endless 10k ohm30% 500 PVZ3H223C01 0.1(50C) 1(23010) Endless 22k ohm30% 500 PVZ3H473C01 0.1(50C) 1(23010) Endless 47k ohm30% 500 PVZ3H104C01 0.1(50C) 1(23010) Endless 100k ohm30% 500 PVZ3H224C01 0.1(50C) 1(23010) Endless 220k ohm30% 500 PVZ3H474C01 0.1(50C) 1(23010) Endless 470k ohm30% 500 PVZ3H105C01 0.1(50C) 1(23010) Endless 1M ohm30% 500 PVZ3H225C01 0.1(50C) 1(23010) Endless 2.2M ohm30% 500 Part Number 2 Operating Temperature Range: -25 to 85 C Soldering Method: Reflow/Soldering Iron Top Adjustment (H 1.55) Part Number Operating Temperature Range: -25 to 85 C Soldering Method: Reflow/Soldering Iron Top Adjustment and Thin Type (H 1.15) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVZ3G221C01 0.1(50C) 1(23010) Endless 220ohm30% 500 PVZ3G471C01 0.1(50C) 1(23010) Endless 470ohm30% 500 PVZ3G102C01 0.1(50C) 1(23010) Endless 1k ohm30% 500 PVZ3G222C01 0.1(50C) 1(23010) Endless 2.2k ohm30% 500 PVZ3G472C01 0.1(50C) 1(23010) Endless 4.7k ohm30% 500 PVZ3G103C01 0.1(50C) 1(23010) Endless 10k ohm30% 500 PVZ3G223C01 0.1(50C) 1(23010) Endless 22k ohm30% 500 PVZ3G473C01 0.1(50C) 1(23010) Endless 47k ohm30% 500 PVZ3G104C01 0.1(50C) 1(23010) Endless 100k ohm30% 500 PVZ3G224C01 0.1(50C) 1(23010) Endless 220k ohm30% 500 PVZ3G474C01 0.1(50C) 1(23010) Endless 470k ohm30% 500 PVZ3G105C01 0.1(50C) 1(23010) Endless 1M ohm30% 500 PVZ3G225C01 0.1(50C) 1(23010) Endless 2.2M ohm30% 500 Part Number Operating Temperature Range: -25 to 85 C Soldering Method: Reflow/Soldering Iron 11 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Rear Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVZ3K221E01 0.1(50C) 1(23010) Endless 220ohm30% 500 PVZ3K471E01 0.1(50C) 1(23010) Endless 470ohm30% 500 PVZ3K102E01 0.1(50C) 1(23010) Endless 1k ohm30% 500 PVZ3K222E01 0.1(50C) 1(23010) Endless 2.2k ohm30% 500 PVZ3K472E01 0.1(50C) 1(23010) Endless 4.7k ohm30% 500 PVZ3K103E01 0.1(50C) 1(23010) Endless 10k ohm30% 500 PVZ3K223E01 0.1(50C) 1(23010) Endless 22k ohm30% 500 PVZ3K473E01 0.1(50C) 1(23010) Endless 47k ohm30% 500 PVZ3K104E01 0.1(50C) 1(23010) Endless 100k ohm30% 500 PVZ3K224E01 0.1(50C) 1(23010) Endless 220k ohm30% 500 PVZ3K474E01 0.1(50C) 1(23010) Endless 470k ohm30% 500 PVZ3K105E01 0.1(50C) 1(23010) Endless 1M ohm30% 500 PVZ3K225E01 0.1(50C) 1(23010) Endless 2.2M ohm30% 500 Part Number Operating Temperature Range: -25 to 85 C Soldering Method: Reflow/Soldering Iron c Construction PVZ3A c Construction c Standard Land Pattern PVZ3G Driver Plate PVZ3A/PVZ3G/PVZ3H 1.1 Wiper 1.9 0.9 #2-Terminal 0.9 1.9 Resistive Element #1-Terminal #3-Terminal Resin Substrate 1.0 0.7 1.0 ( Tolerance in: 0.1 mm) c Construction PVZ3H Driver Plate Wiper 1 #1 Terminal #2 Terminal 4 2 Resistive Element #3 Terminal Resin Substrate Continued on the following page. 12 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Continued from the preceding page. c Construction c Standard Land Pattern PVZ3K PVZ3K Driver Plate 1.5 #2-Terminal 1.0 #1-Terminal a 3.0 Di 1.0 4.0 2 #3-Terminal Wiper Resistive Element (Carbon) Resin Substrate 0.5 3.0 ( Tolerance in: 0.1 mm) c Characteristics Humidity Exposure Res. Change: +10, -2% High Temperature Exposure Res. Change: R< =100kohm***+2, -10% 100kohm<R***+2, -15% Humidity Load Life Res. Change: 10% Load Life Res. Change: R< =100kohm***+2, -10% 100kohm<R***+2, -15% Temperature Cycle Res. Change: 5% Rotational Life Res. Change: 10% (10 cycles) 13 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVZ3 Series Notice c Notice (Operating and Storage Conditions) 2 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. 3. If the trimmer potentiometer is used in DC and high humidity conditions, please connect wiper (#2) for plus and resistive element (#1 or #3) for minus. c Notice (Soldering and Mounting) 1. Soldering (1) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer potentiometer may deviate from the specified characteristics. Do not use flow soldering method (dipping). If you use the flow soldering method, the trimmer potentiometer may not function. (2) Use our standard land dimension. Excessive land area causes displacement due to the effect of the surface tension of the solder. Insufficient land area leads to insufficient soldering strength of the chip. (3) Apply the appropriate amount of solder paste. The thickness of solder paste should be printed from 100 micro m to 150 micro m and the dimension of land pattern used should be Murata's standard land pattern at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals. (4) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. (PVZ Series only) 2. Mounting (1) Do not apply excessive force, preferably 4.9N max. (Ref. 500gf) when the trimmer potentiometer is mounted to the PCB. (2) Do not warp and/or bend the PC board to protect trimmer potentiometer from breakage. (3) In chip placers, the recommended size of the cylindrical pick-up nozzle should be outer dimension 2.5-2.8mm dia. and inner dimension 2mm dia. 3. Cleaning (1) In case there is flux on the resistive element, clean sufficiently with cleaning solvents and completely remove all residual flux. (2) Isopropyl alcohol and ethyl alcohol are applicable solvents for cleaning. If you use any other types of solvents, please evaluate performance with your product. Continued on the following page. 14 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVZ3 Series Notice Continued from the preceding page. c Soldering Profile Reflow Soldering Profile 1. Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu) Temperature (C) T5 T3 T2 2 T4 T1 t2 Limit Profile t3 Standard Profile Time (s) t1 Standard Profile Pre-heating Series PVZ3 Temp. (T1) Time (t1) C sec. 150 to 180 60 to 120 Limit Profile Peak Heating Pre-heating Cycle of Temperature Reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) (T3) C sec. C Time 220 30 to 60 2453 2 C sec. 150 to 180 60 to 120 Peak Cycle of Temperature Reflow Time (t3) (T5) Heating Temp. (T4) C sec. C Time 220 30 to 60 260 2 2. Soldering profile for Eutectic solder (63Sn/37Pb) Temperature (C) (Limit profile: refer to 1) Standard Profile T3 Pre-heating Temp. (T1) t2 T1 Heating Series T2 Standard Profile PVZ3 t1 Time (t1) Temp. (T2) Time (t2) Peak Cycle of Temperature Reflow (T3) C sec. C sec. C Time 150 60 to 120 183 30 230 max. 1 Time (s) Soldering Iron Standard Condition Series Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 PVZ3 c Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in the driver slot. We recommend the screwdrivers below. * Recommended screwdriver for manual adjustment >VESSEL MFG.: NO.9000+1.7x30 (Murata P/N: KMDR080) * Recommended screwdriver for automatic adjustment >TORAY MFG.: JB-2225 (Murata P/N: KMBT070) 2. Don't apply more than 4.9N (Ref.; 500gf) of twist and stress after mounting onto PCB to prevent contact intermittence. If excessive force is applied, the trimmer potentiometer may not function. 3. Please use within the effective rotational angle. Do not have a mechanical stop for over rotation. In cases out of effective rotational angle, the trimmer potentiometer may not function. 4. When using a lock paint to fix the slot position or cover the rotor, please evaluate performance with your product. Lock paint may cause corrosion or electrical contact problems. c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. 15 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers SMD Sealed Type 3mm Size PVG3 Series 3.6 2.2 Dia. #3 0.1 Min. #1 0.6 2.3 2.7 3.6 1.000.15 #2 #1 CLOCKWISE PVG3A #3 0.750.15 ( Tolerance in: 0.3 mm ) 3.6 2.3 0.1 Min. #1 1.000.15 2.7 #3 3.4 2.2 Dia. c Applications 5. Compact Power Supply 6. Wireless Radio module 7. Corner Sensor 8. E-Book 2.0 0.45 0.4 Depth #2 1. Small sensors 2. Optical Transceiver Module 3. Copier 4. Printer 2.0 0.45 0.4 Depth #2 4.5 3 1. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 2. Driver plate with cross-slot is suitable for automatic adjustment. 3. Rotor with large diameter and deep groove improves driver insertion. 4. 3mm and 4mm land pattern can be used without change. (Gull-wing is suitable for 4mm size land pattern.) 5. Heat resistance performance enables high temperature peak reflow soldering. 6. Complies with RoHS directive by new Cd free cermet resistive material. Pb free terminals with Sn plating. 3.4 c Features #2 #1 CLOCKWISE PVG3G #3 0.750.15 ( Tolerance in: 0.3 mm ) Top Adjustment (Standard Type) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVG3A100C01 0.25(70C) 1(21010) 250+/-10 deg. 10ohm20% 150 PVG3A200C01 0.25(70C) 1(21010) 250+/-10 deg. 20ohm20% 150 PVG3A500C01 0.25(70C) 1(21010) 250+/-10 deg. 50ohm20% 150 PVG3A101C01 0.25(70C) 1(21010) 250+/-10 deg. 100ohm20% 150 PVG3A201C01 0.25(70C) 1(21010) 250+/-10 deg. 200ohm20% 150 PVG3A501C01 0.25(70C) 1(21010) 250+/-10 deg. 500ohm20% 150 PVG3A102C01 0.25(70C) 1(21010) 250+/-10 deg. 1k ohm20% 150 PVG3A202C01 0.25(70C) 1(21010) 250+/-10 deg. 2k ohm20% 150 PVG3A502C01 0.25(70C) 1(21010) 250+/-10 deg. 5k ohm20% 150 PVG3A103C01 0.25(70C) 1(21010) 250+/-10 deg. 10k ohm20% 150 PVG3A203C01 0.25(70C) 1(21010) 250+/-10 deg. 20k ohm20% 150 PVG3A503C01 0.25(70C) 1(21010) 250+/-10 deg. 50k ohm20% 150 PVG3A104C01 0.25(70C) 1(21010) 250+/-10 deg. 100k ohm20% 150 PVG3A204C01 0.25(70C) 1(21010) 250+/-10 deg. 200k ohm20% 150 PVG3A504C01 0.25(70C) 1(21010) 250+/-10 deg. 500k ohm20% 150 PVG3A105C01 0.25(70C) 1(21010) 250+/-10 deg. 1M ohm20% 150 PVG3A205C01 0.25(70C) 1(21010) 250+/-10 deg. 2M ohm20% 150 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Reflow/Soldering Iron 16 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Top Adjustment (Gull-Wing Type) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVG3G100C01 0.25(70C) 1(21010) 250+/-10 deg. 10ohm20% 150 PVG3G200C01 0.25(70C) 1(21010) 250+/-10 deg. 20ohm20% 150 PVG3G500C01 0.25(70C) 1(21010) 250+/-10 deg. 50ohm20% 150 PVG3G101C01 0.25(70C) 1(21010) 250+/-10 deg. 100ohm20% 150 PVG3G201C01 0.25(70C) 1(21010) 250+/-10 deg. 200ohm20% 150 PVG3G501C01 0.25(70C) 1(21010) 250+/-10 deg. 500ohm20% 150 PVG3G102C01 0.25(70C) 1(21010) 250+/-10 deg. 1k ohm20% 150 PVG3G202C01 0.25(70C) 1(21010) 250+/-10 deg. 2k ohm20% 150 PVG3G502C01 0.25(70C) 1(21010) 250+/-10 deg. 5k ohm20% 150 PVG3G103C01 0.25(70C) 1(21010) 250+/-10 deg. 10k ohm20% 150 PVG3G203C01 0.25(70C) 1(21010) 250+/-10 deg. 20k ohm20% 150 PVG3G503C01 0.25(70C) 1(21010) 250+/-10 deg. 50k ohm20% 150 PVG3G104C01 0.25(70C) 1(21010) 250+/-10 deg. 100k ohm20% 150 PVG3G204C01 0.25(70C) 1(21010) 250+/-10 deg. 200k ohm20% 150 PVG3G504C01 0.25(70C) 1(21010) 250+/-10 deg. 500k ohm20% 150 PVG3G105C01 0.25(70C) 1(21010) 250+/-10 deg. 1M ohm20% 150 PVG3G205C01 0.25(70C) 1(21010) 250+/-10 deg. 2M ohm20% 150 Part Number 3 Operating Temperature Range: -55 to 125 C Soldering Method: Reflow/Soldering Iron c Construction PVG3A/PVG3G Rotor Cover 2 #2-Terminal Case M #3-Terminal Resistive Element Wiper Ceramic Substrate O-Ring #1-Terminal c Standard Land Pattern PVG3A PVG3G 1.4 1.1 1.2 1.3 0.9 2.5 2.1 2.1 2.5 0.9 1.3 1.4 1.1 ( Tolerance in: 0.1 mm) 1.1 1.2 1.1 ( Tolerance in: 0.1 mm) 17 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Characteristics 3 Temperature Cycle TR : 2% V.S.S.: 1% Humidity TR : 2% V.S.S.: 1% IR : 10M ohm min. Vibration (20G) TR : 1% V.S.S.: 1% Shock (100G) TR : 1% V.S.S.: 1% Temperature Load Life TR : 3% or 3 ohm max., whichever is greater V.S.S.: 1% Low Temperature Exposure TR : 2% V.S.S.: 2% High Temperature Exposure TR : 3% V.S.S.: 2% Rotational Life TR : RV100 kohm ... 3% or 2 ohm max., whichever is greater RG100 kohm ... +0/-10% (50 cycles) TR : Total Resistance Change V.S.S.: Voltage Setting Stability IR : Insulation Resistance R : Standard Total Resistance 18 R50E.pdf Jul.23,2012 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVG3 Series Notice c Notice (Operating and Storage Conditions) 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above 3 c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. c Notice (Soldering and Mounting) 1. Soldering (1) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer potentiometer may deviate from the specified characteristics. (2) This product cannot be soldered using the flow soldering method. If you use the flow soldering method, the trimmer potentiometer may not function. (3) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. (4) Apply the appropriate amount of solder paste. If the amount of solder paste applied to the land is insufficient, the required adhesive strength cannot be obtained. If an excessive amount of solder paste is applied, solder bridging or flux overflow to the resistive element surface can occur. 2. Mounting (1) Use our standard land dimension. Excessive land area causes displacement due to the effect of the surface tension of the solder. Insufficient land area leads to insufficient soldering strength of the chip. (2) Do not apply excessive force, preferably 4.9N max. (Ref. 500gf) when the trimmer potentiometer is mounted to the PCB. (3) Do not warp and/or bend the PC board to protect trimmer potentiometer from breakage. (4) In chip placers, the size of the cylindrical pick-up nozzle should be outer dimension 2.5-3.0mm dia. and inner dimension 2.0-2.5mm dia. 3. Cleaning Isopropyl alcohol and ethyl alcohol are applicable solvents for cleaning. If you use any other types of solvents, please consult with a Murata factory representative prior to using. Continued on the following page. 19 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVG3 Series Notice Continued from the preceding page. c Soldering Profile Reflow Soldering Profile 1. Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu) Temperature (C) T5 T3 T2 T4 T1 t2 Limit Profile t3 Standard Profile 3 Time (s) t1 Standard Profile Pre-heating Heating Series PVG3 Limit Profile Peak Pre-heating Cycle Temperature of Reflow Temp. (T1) Time (t1) (T3) Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. C Time 220 30 to 60 2453 1 150 to 180 60 to 120 C sec. 150 to 180 60 to 120 Heating Peak Cycle Temperature of Reflow (T5) Temp. (T4) Time (t3) C sec. C Time 230 30 to 50 260 +5/-0 2 2. Soldering profile for Eutectic solder (63Sn/37Pb) Temperature (C) (Limit profile: refer to 1) Standard Profile T3 Pre-heating t2 T1 Standard Profile PVG3 t1 Heating Series T2 Peak Cycle Temperature of Reflow (T3) Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. C Time 150 60 to 120 183 30 230 1 Time (s) Soldering Iron Standard Condition Series Temperature of Soldering Iron Tip PVG3 Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 c Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in the driver slot. * Recommended screwdriver for manual adjustment TORAY INDUSTRIES, INC.: SA-2225 (Murata P/N: KMDR070) * Recommended screwdriver bit for automatic adjustment TORAY INDUSTRIES, INC.: JB-2225 (Mutata P/N: KMBT070) We can supply the screwdrivers above. If you place an order, please specify the Murata P/N. 2. When adjusting with an adjustment tool, the applied force to the adjustment screw should not exceed 4.9N (Ref. 500gf). If excessive force is applied, the trimmer potentiometer may not function due to damage. 3. The rotational torque at the position of the adjustment range should not exceed the stop strength. 4. When using a lock paint to fix the slot position, please use adhesive resin without chlorine or sulfur (Three-bond "1401 series") and evaluate performance with your product. Lock paint may cause corrosion or electrical contact problems. c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 20 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers SMD Sealed Type 4mm Size PVM4 Series c Features 4.0 1.5 Dia. 3.8 Dia. #2 0.7 (2.4) 4.7 2.70.1 1. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 2. Available for flow and reflow soldering methods while maintaining unique sealed construction. 3. Simple construction of 3-piece parts achieves high reliability. 4. Large diameter slot of rotor improves driver insertion. 5. Available for cleaning after soldering. 6. High grade version is available (PVM4AxxxD01). 7. Complies with RoHS directive by new Cd free cermet resistive material. Pb free terminals with Sn plating. 2.00.2 #1 #3 0.550.1 0.350.1 Depth 0.75 (0.3) 2.4 1.5 0.8 1.7 0.6 0.85 1.8 0.85 #2 #1 CLOCKWISE #3 ( Tolerance in: 0.3 mm) 4 c Applications 1. Security 2. OA, FA equipment 3. Measuring equipment 4. Professional cameras 5. Encoders 6. Sensors 7. RKE Top Adjustment (Standard Type) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVM4A101C01 0.1(70C) 1(24010) Endless 100ohm25% 250 PVM4A201C01 0.1(70C) 1(24010) Endless 200ohm25% 250 PVM4A501C01 0.1(70C) 1(24010) Endless 500ohm25% 250 PVM4A102C01 0.1(70C) 1(24010) Endless 1k ohm25% 250 PVM4A202C01 0.1(70C) 1(24010) Endless 2k ohm25% 250 PVM4A502C01 0.1(70C) 1(24010) Endless 5k ohm25% 250 PVM4A103C01 0.1(70C) 1(24010) Endless 10k ohm25% 250 PVM4A203C01 0.1(70C) 1(24010) Endless 20k ohm25% 250 PVM4A503C01 0.1(70C) 1(24010) Endless 50k ohm25% 250 PVM4A104C01 0.1(70C) 1(24010) Endless 100k ohm25% 250 PVM4A204C01 0.1(70C) 1(24010) Endless 200k ohm25% 250 PVM4A504C01 0.1(70C) 1(24010) Endless 500k ohm25% 250 PVM4A105C01 0.1(70C) 1(24010) Endless 1M ohm25% 250 PVM4A205C01 0.1(70C) 1(24010) Endless 2M ohm25% 250 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Reflow/Soldering Iron 21 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Top Adjustment (High-Liability Type) Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PVM4A101D01 0.25(70C) 1(24010) Endless 100ohm20% 100 PVM4A201D01 0.25(70C) 1(24010) Endless 200ohm20% 100 PVM4A501D01 0.25(70C) 1(24010) Endless 500ohm20% 100 PVM4A102D01 0.25(70C) 1(24010) Endless 1k ohm20% 200 PVM4A202D01 0.25(70C) 1(24010) Endless 2k ohm20% 200 PVM4A502D01 0.25(70C) 1(24010) Endless 5k ohm20% 200 PVM4A103D01 0.25(70C) 1(24010) Endless 10k ohm20% 150 PVM4A203D01 0.25(70C) 1(24010) Endless 20k ohm20% 150 PVM4A503D01 0.25(70C) 1(24010) Endless 50k ohm20% 150 PVM4A104D01 0.25(70C) 1(24010) Endless 100k ohm20% 150 PVM4A204D01 0.25(70C) 1(24010) Endless 200k ohm20% 150 PVM4A504D01 0.25(70C) 1(24010) Endless 500k ohm20% 150 PVM4A105D01 0.25(70C) 1(24010) Endless 1M ohm20% 150 PVM4A205D01 0.25(70C) 1(24010) Endless 2M ohm20% 150 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Reflow/Soldering Iron 4 c Construction c Standard Land Pattern 1.7 Rotor 3.2 1.8 #2 Terminal Wiper Rubber 1.2 3.2 Ceramic Substrate #1 Terminal Resistive Element 1.1 #3 Terminal 1.6 c Characteristics Item PVM4ApppC01 PVM4ApppD01 Humidity Exposure Res. Change: 3% Res. Change: 2% High Temperature Exposure Res. Change: 3% Res. Change: 2% Humidity Load Life Res. Change: 3% Res. Change: 3% Temperature Load Life Res. Change: 3% Res. Change: 3% Temperature Cycle Res. Change: 3% Res. Change: 2% Rotational Life Res. Change: 10% (20 cycles) Res. Change: 5% (100 cycles) 22 1.1 ( Tolerance in: 0.1 mm) R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVM4 Series Notice c Notice (Operating and Storage Conditions) 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. 4 c Notice (Soldering and Mounting) 1. Soldering (1) Can be soldered by reflow soldering method, flow soldering method, and soldering iron. (2) Use our standard land dimension. Excessive land area causes displacement due to the effect of the surface tension of the solder. Insufficient land area leads to insufficient soldering strength of the chip. (3) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer potentiometer may deviate from the specified characteristics. (4) Apply the appropriate amount of solder paste. The thickness of solder paste should be printed from 100 micro m to 150 micro m and the dimension of land pattern used should be Murata's standard land pattern at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals. (5) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. 2. Mounting (1) Do not apply excessive force, preferably 9.8N max. (Ref. 1kgf) when the trimmer potentiometer is mounted to the PCB. (2) Do not warp and/or bend the PC board to protect trimmer potentiometer from breakage. (3) In chip placers, the recommended size of the cylindrical pick-up nozzle should be outer dimension 4.0mm dia. and inner dimension 2.0mm dia. 3. Cleaning Isopropyl alcohol and ethyl alcohol are available materials for cleaning. For other materials, please consult with a Murata factory representative prior to using. Continued on the following page. 23 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVM4 Series Notice Continued from the preceding page. c Soldering Profile Flow Soldering Profile Temperature (C) Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb) T3 T2 t2 Heating T1 Limit Profile Standard Profile Time (s) t1 Pre-heating Standard Profile Pre-heating Limit Profile Heating PVM4 Heating Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. Time C sec. C sec. Time 150 60 to 120 250 5 max. 1 150 60 to 120 2653 5 max. 2 Series Temp. (T1) Time (t1) Temp. (T3) Time (t2) Cycle of Flow Reflow Soldering Profile 1. Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu) Temperature (C) T5 T3 T2 T4 T1 t2 Limit Profile t3 Standard Profile Time (s) t1 Standard Profile Pre-heating Heating Series PVM4 Limit Profile Peak Pre-heating Cycle Temperature of Reflow Temp. (T1) Time (t1) (T3) Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. C Time 220 30 to 60 2453 2 150 to 180 60 to 120 C sec. 150 to 180 60 to 120 Heating Temp. (T4) Time (t3) Peak Cycle Temperature of Reflow (T5) C sec. C Time 230 30 to 50 260 +5/-0 2 2. Soldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to 1) Temperature (C) 4 Pre-heating Cycle of Flow Standard Profile T3 Pre-heating t2 T1 Standard Profile PVM4 t1 Heating Series T2 Peak Cycle Temperature of Reflow (T3) Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. C Time 150 60 to 120 183 30 230 1 Time (s) Soldering Iron Standard Condition Series PVM4 Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 Continued on the following page. 24 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. R50E.pdf Jul.23,2012 PVM4 Series Notice Continued from the preceding page. c Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in the driver slot. We recommend the screwdriver below. * Recommended screwdriver for manual adjustment VESSEL MFG.: NO. 9000-2.6x30 (Murata P/N: KMDR120) We can supply the screwdrivers above. If you place an order, please specify the Murata P/N. 2. Do not apply more than 4.9N (Ref. 500gf) of twist and stress after mounting onto PCB to prevent contact intermittence. If excessive force is applied, the trimmer potentiometer may not function. 3. Please use within the effective rotational angle. The potentiometer does not have a mechanical stop for over rotation. In cases out of effective rotational angle, the trimmer potentiometer may not function. 4. When using a lock paint to fix the slot position, please use adhesive resin without chlorine or sulfur (Three-bond "1401 series") and evaluate performance with your product. Lock paint may cause corrosion or electrical contact problems. c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. 4 25 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers SMD Sealed Type Multi-turn PVG5 Series c Features 0.9 4.8 1. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 2. Available with reflow soldering method 3. Available for ultrasonic cleaning after soldering. 4. Clutch mechanism prevents excessive wiper rotation. 5. Both top and side adjustment directions. 6. Much smaller volume (1/5-1/2) than leaded multi-turn potentiometer. 7. Complies with RoHS directive by new Cd free cermet resistive material. Pb free terminals with Sn plating. 1.1 ADJ. Slot Dia. o1.5 Width 0.6 Depth 0.5 Marking 2.4 1.2 3-0.9 #2 0.5 2.6 3.5 3.9 5.1 #3 0.2 #1 2.5 2-0.7 Circuit #2 (Wiper) PVG5A #1 2-0.7 #3 (Tolerance:in0.3 mm) Clockwise 2.4 Marking 4.9 1.2 3-0.9 2.6 0.50 ADJ. Slot Dia. o1.5 Width 0.6 Depth 0.5 3.7 1. Measuring instruments 4. Power supply 2. OA equipment 5. Sensors 3. Medical equipment 6. Base station for cellular phones 4.8 c Applications 5 3-0.7 2.3 #2 Circuit #3 PVG5H #1 #3 Clockwise #1 2-0.7 1.1 #2 (Wiper) (Tolerance:in0.3 mm) Top Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PVG5A100C03 0.25(70C) 11 10ohm10% 150 PVG5A200C03 0.25(70C) 11 20ohm10% 150 PVG5A500C03 0.25(70C) 11 50ohm10% 150 PVG5A101C03 0.25(70C) 11 100ohm10% 150 PVG5A201C03 0.25(70C) 11 200ohm10% 150 PVG5A501C03 0.25(70C) 11 500ohm10% 150 PVG5A102C03 0.25(70C) 11 1k ohm10% 150 PVG5A202C03 0.25(70C) 11 2k ohm10% 150 PVG5A502C03 0.25(70C) 11 5k ohm10% 150 PVG5A103C03 0.25(70C) 11 10k ohm10% 150 PVG5A203C03 0.25(70C) 11 20k ohm10% 150 PVG5A503C03 0.25(70C) 11 50k ohm10% 150 PVG5A104C03 0.25(70C) 11 100k ohm10% 150 PVG5A204C03 0.25(70C) 11 200k ohm10% 150 PVG5A504C03 0.25(70C) 11 500k ohm10% 150 PVG5A105C03 0.25(70C) 11 1M ohm10% 150 PVG5A205C03 0.25(70C) 11 2M ohm10% 150 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Reflow/Soldering Iron 26 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Side Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PVG5H100C03 0.25(70C) 11 10ohm10% 150 PVG5H200C03 0.25(70C) 11 20ohm10% 150 PVG5H500C03 0.25(70C) 11 50ohm10% 150 PVG5H101C03 0.25(70C) 11 100ohm10% 150 PVG5H201C03 0.25(70C) 11 200ohm10% 150 PVG5H501C03 0.25(70C) 11 500ohm10% 150 PVG5H102C03 0.25(70C) 11 1k ohm10% 150 PVG5H202C03 0.25(70C) 11 2k ohm10% 150 PVG5H502C03 0.25(70C) 11 5k ohm10% 150 PVG5H103C03 0.25(70C) 11 10k ohm10% 150 PVG5H203C03 0.25(70C) 11 20k ohm10% 150 PVG5H503C03 0.25(70C) 11 50k ohm10% 150 PVG5H104C03 0.25(70C) 11 100k ohm10% 150 PVG5H204C03 0.25(70C) 11 200k ohm10% 150 PVG5H504C03 0.25(70C) 11 500k ohm10% 150 PVG5H105C03 0.25(70C) 11 1M ohm10% 150 PVG5H205C03 0.25(70C) 11 2M ohm10% 150 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Reflow/Soldering Iron c Construction Adjustment Screw Gear 5 Case #2 Terminal Wiper Resistive Element #1, #3 Terminal Ceramic Substrate c Standard Land Pattern PVG5A PVG5H 2.0 2.8 2.25 1.6 2.8 2.25 1.6 1.6 1.6 2.0 1.3 1.2 1.3 (Tolerance:in0.1 mm) 1.3 1.0 1.3 (Tolerance:in0.1 mm) 27 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Characteristics Temperature Cycle TR : 2% V.S.S.: 1% Humidity TR IR Vibration (20G) TR : 1% V.S.S.: 1% Shock (100G) TR : 1% V.S.S.: 1% Temperature Load Life TR : 3% or 3 ohm max., whichever is greater V.S.S.: 1% Low Temperature Exposure TR : 1% V.S.S.: 1% High Temperature Exposure TR : 2% V.S.S.: 1% Rotational Life TR : 2% : 10M ohm min. : 3% or 3 ohm max., whichever is greater (100 cycles) TR : Total Resistance Change V.S.S.: Voltage Setting Stability IR : Insulation Resistance 5 28 R50E.pdf Jul.23,2012 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVG5 Series Notice c Notice (Operating and Storage Conditions) 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. 5 c Notice (Soldering and Mounting) 1. Soldering (1) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (2) This product cannot be soldered using the flow soldering method. If you use the flow soldering method, the trimmer potentiometer may not function. (3) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. (4) Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals. 2. Mounting (1) Use our standard land dimension. Excessive land area causes displacement due to the effect of the surface tension of the solder. Insufficient land area leads to insufficient soldering strength of the chip. (2) Do not apply excessive force, preferably 9.8N max. (Ref. 1kgf) when the trimmer potentiometer is mounted to the PCB. (3) Do not warp and/or bend the PC board to protect trimmer potentiometer from breakage. (4) In chip placers, the recommended size of the cylindrical pick-up nozzle should be outer dimension 4.0mm dia. and inner dimension 2.0mm dia. 3. Cleaning Isopropyl alcohol and ethyl alcohol are applicable solvents for cleaning. If you use any other types of solvents, please consult with a Murata factory representative prior to using. Continued on the following page. 29 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PVG5 Series Notice Continued from the preceding page. c Soldering Profile Reflow Soldering Profile 1. Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu) Temperature (C) T5 T3 T2 T4 T1 t2 Limit Profile t3 Standard Profile Time (s) t1 Standard Profile Pre-heating Series PVG5 Limit Profile Peak Pre-heating Cycle of Temperature Reflow Temp. (T1) Time (t1) Time (t2) (T3) Heating Temp. (T1) Time (t1) Temp. (T2) C sec. C sec. C Time 220 30 to 60 2453 2 150 to 180 60 to 120 C sec. 150 to 180 60 to 120 Peak Cycle of Temperature Reflow Time (t3) (T5) Heating Temp. (T4) C sec. C Time 230 30 to 50 260 +5/-0 2 2. Soldering profile for Eutectic solder (63Sn/37Pb) Temperature (C) (Limit profile: refer to 1) 5 Standard Profile T3 Pre-heating T2 t2 T1 Standard Profile PVG5 t1 Peak Cycle of Temperature Reflow Time (t2) (T3) Heating Series Temp. (T1) Time (t1) C sec. Temp. (T2) C sec. C Time 150 60 to 120 183 30 230 1 Time (s) Soldering Iron Standard Condition Series Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 PVG5 c Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in the driver slot. We recommend the screwdrivers below. * Recommended screwdrivers for manual adjustment <PVG5 series> VESSEL MFG.: NO.9000-1.3x30 (Murata P/N: KMDR130) We can supply the screwdrivers above. If you place an order, please specify the Murata P/N. c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. 30 2. When adjusting with a screwdriver, do not apply excessive force, preferable 4.9N max. (Ref 500gf). 3. When using a lock paint to fix the slot position, please use adhesive resin without chlorine or sulfur (Three-bond "1401 series") and evaluate performance with your product. Lock paint may cause corrosion or electrical problems. R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers Lead Sealed Type Single-turn PV32 Series c Features 1. Round body shape enables smaller area mount than same 6mm square potentiometer. 2. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 3. Available for ultrasonic cleaning after soldering. 4. Flammability: UL94V-0 5. PV32 series complies with RoHS directive. 4.10.3 2.8 Dia. 4.60.3 0.6 1.0 Depth 0.35 max. 8.01.0 6.60.5 Dia. 0.9 Dia. max. 3-0.50.1 Dia. #1 #2 #3 #2 906 0.4 #3 ( Tolerancein: 0.3 mm ) 5 5. Printers 6. Sensors 7. Power supply 2. 5 1. HDTVs 2. Professional cameras 3. CATV 4. FAX CL PV32H 2. c Applications #1 CLOCKWISE 6.40.4 6.9 5.90.4 8.00.3 5.01.0 4.70.3 0.20.1 6.01.0 2.8 Dia. 0.6 1.0 Depth 3-0.50.1 Dia. #3 #2 #1 5.0 1.0 PV32N 2.5 #2 2.5 2.5 #1 #3 CLOCKWISE ( Tolerance in: 0.3 mm) 6 Top Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PV32H100A01 0.5(70C) 1(2305) 270+/-5 deg. 10ohm20% 100 PV32H200A01 0.5(70C) 1(2305) 270+/-5 deg. 20ohm20% 100 PV32H500A01 0.5(70C) 1(2305) 270+/-5 deg. 50ohm20% 100 PV32H101A01 0.5(70C) 1(2305) 270+/-5 deg. 100ohm20% 100 PV32H201A01 0.5(70C) 1(2305) 270+/-5 deg. 200ohm20% 100 PV32H501A01 0.5(70C) 1(2305) 270+/-5 deg. 500ohm20% 100 PV32H102A01 0.5(70C) 1(2305) 270+/-5 deg. 1k ohm20% 100 PV32H202A01 0.5(70C) 1(2305) 270+/-5 deg. 2k ohm20% 100 PV32H502A01 0.5(70C) 1(2305) 270+/-5 deg. 5k ohm20% 100 PV32H103A01 0.5(70C) 1(2305) 270+/-5 deg. 10k ohm20% 100 PV32H203A01 0.5(70C) 1(2305) 270+/-5 deg. 20k ohm20% 100 PV32H503A01 0.5(70C) 1(2305) 270+/-5 deg. 50k ohm20% 100 PV32H104A01 0.5(70C) 1(2305) 270+/-5 deg. 100k ohm20% 100 PV32H204A01 0.5(70C) 1(2305) 270+/-5 deg. 200k ohm20% 100 PV32H504A01 0.5(70C) 1(2305) 270+/-5 deg. 500k ohm20% 100 PV32H105A01 0.5(70C) 1(2305) 270+/-5 deg. 1M ohm20% 100 PV32H205A01 0.5(70C) 1(2305) 270+/-5 deg. 2M ohm20% 100 PV32H505A01 0.5(70C) 1(2305) 270+/-5 deg. 5M ohm20% 100 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron 31 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Side Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Mechanical Rotation Angle Total Resistance Value TCR (ppm/C) PV32N100A01 0.5(70C) 1(2305) 270+/-5 deg. 10ohm20% 100 PV32N200A01 0.5(70C) 1(2305) 270+/-5 deg. 20ohm20% 100 PV32N500A01 0.5(70C) 1(2305) 270+/-5 deg. 50ohm20% 100 PV32N101A01 0.5(70C) 1(2305) 270+/-5 deg. 100ohm20% 100 PV32N201A01 0.5(70C) 1(2305) 270+/-5 deg. 200ohm20% 100 PV32N501A01 0.5(70C) 1(2305) 270+/-5 deg. 500ohm20% 100 PV32N102A01 0.5(70C) 1(2305) 270+/-5 deg. 1k ohm20% 100 PV32N202A01 0.5(70C) 1(2305) 270+/-5 deg. 2k ohm20% 100 PV32N502A01 0.5(70C) 1(2305) 270+/-5 deg. 5k ohm20% 100 PV32N103A01 0.5(70C) 1(2305) 270+/-5 deg. 10k ohm20% 100 PV32N203A01 0.5(70C) 1(2305) 270+/-5 deg. 20k ohm20% 100 PV32N503A01 0.5(70C) 1(2305) 270+/-5 deg. 50k ohm20% 100 PV32N104A01 0.5(70C) 1(2305) 270+/-5 deg. 100k ohm20% 100 PV32N204A01 0.5(70C) 1(2305) 270+/-5 deg. 200k ohm20% 100 PV32N504A01 0.5(70C) 1(2305) 270+/-5 deg. 500k ohm20% 100 PV32N105A01 0.5(70C) 1(2305) 270+/-5 deg. 1M ohm20% 100 PV32N205A01 0.5(70C) 1(2305) 270+/-5 deg. 2M ohm20% 100 PV32N505A01 0.5(70C) 1(2305) 270+/-5 deg. 5M ohm20% 100 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron c Construction Rotor Cover "O"-Ring Wiper Resistive Element Ceramic Substrate 6 Terminal c Standard Mounting Holes PV32H PV32N 2.5 2.5 2. 2. 5 3-0.9 5 (1) (3) 2.5 (2) 3-0.9 (1) (3) (2) Tolerance: 0.1 in mm 32 Tolerance: 0.1 in mm !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. R50E.pdf Jul.23,2012 c Characteristics Temperature Cycle TR : 2% V.S.S.: 1% Humidity TR IR Vibration (20G) TR : 1% V.S.S.: 1% Shock (100G) TR : 1% V.S.S.: 1% Temperature Load Life TR : 2% V.S.S.: 2% Low Temperature Exposure TR : 2% V.S.S.: 1% High Temperature Exposure TR : 2% V.S.S.: 1% Rotational Life TR : 2% : 100M ohm min. : 4% (200 cycles) TR : Total Resistance Change V.S.S.: Voltage Setting Stability IR : Insulation Resistance 6 33 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PV32 Series Notice c Notice (Operating and Storage Conditions) 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. c Notice (Soldering and Mounting) 6 1. Soldering (1) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer potentiometer may deviate from the specified characteristics. (2) To minimize mechanical stress when adjusting, the trimmer potentiometer should be mounted onto the PCB without a gap. (3) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. 2. Mounting (1) Use the PCB hole to meet the pin of the trimmer potentiometer. If the trimmer potentiometer is installed into an insufficient PCB hole, the trimmer potentimeter may be damaged by mechanical stress. (2) Do not apply excessive force, preferably 9.8N max. (Ref. 1kgf) when the trimmer potentiometer is mounted to the PCB. 3. Cleaning Isopropyl alcohol and ethyl alcohol are applicable solvents for cleaning. If you use any other types of solvents, please consult with a Murata factory representative prior to using. Continued on the following page. 34 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PV32 Series Notice Continued from the preceding page. c Soldering Profile Flow Soldering Profile Temperature (C) Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb) T3 T2 t2 Heating T1 Limit Profile Standard Profile Time (s) t1 Pre-heating Standard Profile Pre-heating Limit Profile Heating Heating Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. Time C sec. C sec. Time 150 60 to 120 250 5 max. 1 150 60 to 120 260 3 max. 1 Series PV32 Pre-heating Cycle of Flow Temp. (T1) Time (t1) Temp. (T3) Time (t2) Cycle of Flow Soldering Iron Standard Condition Series Temperature of Soldering Iron Tip PV32 Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 c Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in the driver slot. We recommend the screwdrivers below. * Recommended screwdriver for manual adjustment <PV32 series> ENGINEER INC.: DA-40 (Murata P/N: KMDR180) We can supply the screwdrivers above. If you place an order, please specify the Murata P/N. 2. When adjusting with an adjustment tool, the applied force to the adjustment screw should not exceed 4.9N (Ref. 500gf). If excessive force is applied, the trimmer potentiometer may not function due to damage. 3. The rotational torque at the position of the adjustment range should not exceed the stop strength. 4. When using a lock paint to fix the slot position, please use adhesive resin without chlorine or sulfur (Three-bond "1401 series") and evaluate performance with your product. Lock paint may cause corrosion or electrical contact problems. 6 c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. 35 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Trimmer Potentiometers Lead Sealed Type Multi-turn PV12/PV37/PV36 Series PV12 Series c Features 0.60.1 0.70.1 Depth 3-0.50.1 Dia. 0.5 2.5 2.5 #2 2.5 #2 #3 #1 #1 #3 CLOCKWISE PV12P c Applications ( Tolerance in: 0.3 mm) 5. Printers 6. Sensors 7. Switching power supplies 7.70.3 9.00.3 5.10.3 0.5 2.50.1 0.60.1 0.70.1 Depth 7.01.0 1. HDTVs 2. Professional cameras 3. CATV 4. FAX 7.01.0 6.60.1 7.60.1 Dia. 2.50.1 1. The unique inner gear system recognizes the position of the center of the shaft of the potentiometer. 2. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 3. Available for ultrasonic cleaning after soldering. 4. Clutch mechanism prevents excessive wiper rotation. 5. PV12 series complies with RoHS directive. 3-0.50.1 Dia. #1 #2 #3 7.60.3 6.30.3 3.6 #2 #1 2.5 PV12T 2.5 2.5 #3 CLOCKWISE ( Tolerance in: 0.3 mm) Top Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PV12P100A01 0.5(70C) 4 10ohm10% 100 PV12P200A01 0.5(70C) 4 20ohm10% 100 PV12P500A01 0.5(70C) 4 50ohm10% 100 PV12P101A01 0.5(70C) 4 100ohm10% 100 PV12P201A01 0.5(70C) 4 200ohm10% 100 PV12P501A01 0.5(70C) 4 500ohm10% 100 PV12P102A01 0.5(70C) 4 1k ohm10% 100 PV12P202A01 0.5(70C) 4 2k ohm10% 100 PV12P502A01 0.5(70C) 4 5k ohm10% 100 PV12P103A01 0.5(70C) 4 10k ohm10% 100 PV12P203A01 0.5(70C) 4 20k ohm10% 100 PV12P503A01 0.5(70C) 4 50k ohm10% 100 PV12P104A01 0.5(70C) 4 100k ohm10% 100 PV12P204A01 0.5(70C) 4 200k ohm10% 100 PV12P504A01 0.5(70C) 4 500k ohm10% 100 PV12P105A01 0.5(70C) 4 1M ohm10% 100 PV12P205A01 0.5(70C) 4 2M ohm10% 100 Part Number 7 Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron 36 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Side Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PV12T100A01 0.5(70C) 4 10ohm10% 100 PV12T200A01 0.5(70C) 4 20ohm10% 100 PV12T500A01 0.5(70C) 4 50ohm10% 100 PV12T101A01 0.5(70C) 4 100ohm10% 100 PV12T201A01 0.5(70C) 4 200ohm10% 100 PV12T501A01 0.5(70C) 4 500ohm10% 100 PV12T102A01 0.5(70C) 4 1k ohm10% 100 PV12T202A01 0.5(70C) 4 2k ohm10% 100 PV12T502A01 0.5(70C) 4 5k ohm10% 100 PV12T103A01 0.5(70C) 4 10k ohm10% 100 PV12T203A01 0.5(70C) 4 20k ohm10% 100 PV12T503A01 0.5(70C) 4 50k ohm10% 100 PV12T104A01 0.5(70C) 4 100k ohm10% 100 PV12T204A01 0.5(70C) 4 200k ohm10% 100 PV12T504A01 0.5(70C) 4 500k ohm10% 100 PV12T105A01 0.5(70C) 4 1M ohm10% 100 PV12T205A01 0.5(70C) 4 2M ohm10% 100 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron c Construction Shaft Case "O"-Ring Gear Rotor Insert Wiper Ceramic Resistive Element Alumina Substrate Terminal c Standard Mounting Holes PV12P 2.5 2.5 3-0.9 (2) (3) 2.5 3-0.9 7 PV12T (3) 2.5 (1) 2.5 2.5 (1) (2) Tolerance: 0.1 in mm Tolerance: 0.1 in mm 37 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. c Characteristics Temperature Cycle TR : 2% V.S.S.: 1% Humidity TR IR Vibration (20G) TR : 1% V.S.S.: 1% Shock (100G) TR : 1% V.S.S.: 1% Temperature Load Life TR : 3% V.S.S.: 2% Low Temperature Exposure TR : 3% V.S.S.: 1.5% High Temperature Exposure TR : 3% V.S.S.: 1.5% Rotational Life TR : 2% : 100M ohm min. : 3% (200 cycles) TR : Total Resistance Change V.S.S.: Voltage Setting Stability IR : Insulation Resistance 7 38 R50E.pdf Jul.23,2012 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PV37 Series c Features 1.1 6.4 1.2 1. Smaller volume (about one-third) than 25-turn potentiometer 2. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 3. Available for ultrasonic cleaning after soldering. 4. Clutch mechanism prevents excessive wiper rotation. 5. Both top and side adjustment directions. 6. Complies with RoHS directive by new Cd free cermet resistive material. Pb free terminals with Sn plating. 5.01.0 6.7 0.6 1.0 Marking 1.80.2 Dia. 0.60.2 3-0.40.1 Dia. #3 #2 2.5 #2 #1 #3 CLOCKWISE 2.5 4.0 ( Tolerance in: 0.3 mm) 0.7 PV37W #1 2.5 c Applications 1. Measuring instruments 4. Power supply 2. OA equipment 5. Base station for cellular phones 3. Medical equipment 6.4 0.6 1.0 Marking 6.7 5.01.0 0.60.2 1.80.2 Dia. 1.1 1.1 3-0.40.1 Dia. #3 #2 2.5 #1 2.5 0.7 4.0 #1 #3 CLOCKWISE 2.5 #2 PV37X ( Tolerance in: 0.3 mm) Top Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PV37W100C01 0.25(85C) 12 10ohm10% 150 PV37W200C01 0.25(85C) 12 20ohm10% 150 PV37W500C01 0.25(85C) 12 50ohm10% 150 PV37W101C01 0.25(85C) 12 100ohm10% 150 PV37W201C01 0.25(85C) 12 200ohm10% 150 PV37W501C01 0.25(85C) 12 500ohm10% 150 PV37W102C01 0.25(85C) 12 1k ohm10% 150 PV37W202C01 0.25(85C) 12 2k ohm10% 150 PV37W502C01 0.25(85C) 12 5k ohm10% 150 PV37W103C01 0.25(85C) 12 10k ohm10% 150 PV37W203C01 0.25(85C) 12 20k ohm10% 150 PV37W503C01 0.25(85C) 12 50k ohm10% 150 PV37W104C01 0.25(85C) 12 100k ohm10% 150 PV37W204C01 0.25(85C) 12 200k ohm10% 150 PV37W504C01 0.25(85C) 12 500k ohm10% 150 PV37W105C01 0.25(85C) 12 1M ohm10% 150 PV37W205C01 0.25(85C) 12 2M ohm10% 150 Part Number 7 Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron 39 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Side Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PV37X100C01 0.25(85C) 12 10ohm10% 150 PV37X200C01 0.25(85C) 12 20ohm10% 150 PV37X500C01 0.25(85C) 12 50ohm10% 150 PV37X101C01 0.25(85C) 12 100ohm10% 150 PV37X201C01 0.25(85C) 12 200ohm10% 150 PV37X501C01 0.25(85C) 12 500ohm10% 150 PV37X102C01 0.25(85C) 12 1k ohm10% 150 PV37X202C01 0.25(85C) 12 2k ohm10% 150 PV37X502C01 0.25(85C) 12 5k ohm10% 150 PV37X103C01 0.25(85C) 12 10k ohm10% 150 PV37X203C01 0.25(85C) 12 20k ohm10% 150 PV37X503C01 0.25(85C) 12 50k ohm10% 150 PV37X104C01 0.25(85C) 12 100k ohm10% 150 PV37X204C01 0.25(85C) 12 200k ohm10% 150 PV37X504C01 0.25(85C) 12 500k ohm10% 150 PV37X105C01 0.25(85C) 12 1M ohm10% 150 PV37X205C01 0.25(85C) 12 2M ohm10% 150 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron c Construction c Standard Mounting Holes PV37W/PV37X Gear Case 2.5 3-0.9 2.5 (1) (3) 2.5 Adjustment Screw Terminal (2) Wiper Cermet Resistive Element Alumina Substrate 7 c Characteristics Temperature Cycle TR : 1% V.S.S.: 1% Humidity TR IR Vibration (20G) TR : 1% V.S.S.: 1% Shock (100G) TR : 1% V.S.S.: 1% Temperature Load Life TR : 2% V.S.S.: 1% Low Temperature Exposure TR : 1% V.S.S.: 1% High Temperature Exposure TR : 2% V.S.S.: 1% Rotational Life TR : 2% : 100M ohm min. : RV100 ohm ... 3% RG100 ohm ... 2% (200 cycles) TR : Total Resistance Change V.S.S.: Voltage Setting Stability IR : Insulation Resistance R : Standard Total Resistance 40 Tolerance: 0.1 in mm R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PV36 Series c Features 1.2 2.0 Dia. 9.6 1. High resolution 25-turns potentiometer enables precision adjustment easily. 2. Sealed construction protects the interior from dust and liquid, which achieves stable performance. 3. Available for ultrasonic cleaning after soldering. 4. Clutch mechanism prevents excessive wiper rotation. 5. Both top and side adjustment directions. 6. Complies with RoHS directive by new Cd free cermet resistive material. Pb free terminals with Sn plating. 0.6 1.3 6.01.0 0.5 10.0 0.7 1.3 Marking 3-0.50.1 Dia. #3 #2 #1 #2 (Wiper) 2.5 2.5 #1 2.5 5.0 PV36W #3 Clockwise ( Tolerance : 0.3 in mm ) c Applications 9.6 1. Measuring instruments 4. Power supply 2. OA equipment 5. Base station for cellular phones 3. Medical equipment 0.7 1.3 Marking 6.01.0 10.0 2.0 Dia. 0.6 0.5 1.3 1.2 3-0.50.1 Dia. #3 #2 #1 2.5 2.5 #2 (Wiper) #1 #3 ( Tolerance : 0.3 in mm 2.5 Clockwise 5.0 PV36X ) Top Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PV36W100C01 0.5(70C) 25 10ohm10% 150 PV36W200C01 0.5(70C) 25 20ohm10% 150 PV36W500C01 0.5(70C) 25 50ohm10% 150 PV36W101C01 0.5(70C) 25 100ohm10% 150 PV36W201C01 0.5(70C) 25 200ohm10% 100 PV36W501C01 0.5(70C) 25 500ohm10% 100 PV36W102C01 0.5(70C) 25 1k ohm10% 100 PV36W202C01 0.5(70C) 25 2k ohm10% 100 PV36W502C01 0.5(70C) 25 5k ohm10% 100 PV36W103C01 0.5(70C) 25 10k ohm10% 100 PV36W203C01 0.5(70C) 25 20k ohm10% 100 PV36W503C01 0.5(70C) 25 50k ohm10% 100 PV36W104C01 0.5(70C) 25 100k ohm10% 100 PV36W204C01 0.5(70C) 25 200k ohm10% 100 PV36W504C01 0.5(70C) 25 500k ohm10% 100 PV36W105C01 0.5(70C) 25 1M ohm10% 100 PV36W205C01 0.5(70C) 25 2M ohm10% 100 Part Number 7 Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron 41 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Side Adjustment Power Rating (W) Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/C) PV36X100C01 0.5(70C) 25 10ohm10% 150 PV36X200C01 0.5(70C) 25 20ohm10% 150 PV36X500C01 0.5(70C) 25 50ohm10% 150 PV36X101C01 0.5(70C) 25 100ohm10% 150 PV36X201C01 0.5(70C) 25 200ohm10% 100 PV36X501C01 0.5(70C) 25 500ohm10% 100 PV36X102C01 0.5(70C) 25 1k ohm10% 100 PV36X202C01 0.5(70C) 25 2k ohm10% 100 PV36X502C01 0.5(70C) 25 5k ohm10% 100 PV36X103C01 0.5(70C) 25 10k ohm10% 100 PV36X203C01 0.5(70C) 25 20k ohm10% 100 PV36X503C01 0.5(70C) 25 50k ohm10% 100 PV36X104C01 0.5(70C) 25 100k ohm10% 100 PV36X204C01 0.5(70C) 25 200k ohm10% 100 PV36X504C01 0.5(70C) 25 500k ohm10% 100 PV36X105C01 0.5(70C) 25 1M ohm10% 100 PV36X205C01 0.5(70C) 25 2M ohm10% 100 Part Number Operating Temperature Range: -55 to 125 C Soldering Method: Flow/Soldering Iron c Construction c Standard Mounting Holes PV36W/X Adjustment Screw Terminal 3-0.9 (3) (2) 2.5 Case Cermet Resistive Element Gear c Characteristics Temperature Cycle TR : 2% V.S.S.: 1% Humidity TR IR Vibration (20G) TR : 1% V.S.S.: 1% Shock (100G) TR : 1% V.S.S.: 1% Temperature Load Life TR : 3% V.S.S.: 1% Low Temperature Exposure TR : 2% V.S.S.: 1% High Temperature Exposure TR : 3% V.S.S.: 1% Rotational Life TR : 2% : 100M ohm min. : RV1k ohm, RU500k ohm ... 5% 1k ohmFRF500k ohm ... 3% (200 cycles) TR : Total Resistance Change V.S.S.: Voltage Setting Stability IR : Insulation Resistance R : Standard Total Resistance 42 2.5 Wiper Alumina Substrate 7 (1) Tolerance: 0.1 in mm R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PV12/PV37/PV36 Series Notice c Notice (Operating and Storage Conditions) 1. Store in temperatures of -10 to +40C and relative humidity of 30-85%. 2. Do not store in or near corrosive gases. 3. Use within six months after delivery. 4. Open the package just before using. 5. Do not store under direct sunlight. 6. If you use the trimmer potentiometer in an environment other than listed at right, please consult with a Murata factory representative prior to using. The trimmer potentiometer should not be used under the following environmental conditions: (1) Corrosive gaseous atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (Ex. Oil, Medical liquid, Organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage or electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above c Notice (Rating) 1. When using with partial load (rheostat), minimize the power depending on the resistance value. 2. The maximum input voltage to a trimmer potentiometer should not exceed (P*R)^1/2 or the maximum operating voltage, whichever is smaller. c Notice (Soldering and Mounting) 1. Soldering (1) Soldering conditions Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer potentiometer may deviate from the specified characteristics. (2) To minimize mechanical stress when adjusting, the trimmer potentiometer should be mounted onto the PCB without a gap. (3) The soldering iron should not come in contact with the case of the trimmer potentiometer. If such contact does occur, the trimmer potentiometer may be damaged. 2. Mounting (1) Use the PCB hole to meet the pin of the trimmer potentiometer. If the trimmer potentiometer is installed into an insufficient PCB hole, the trimmer potentimeter may be damaged by mechanical stress. (2) Do not apply excessive force, preferably 9.8N max. (Ref. 1kgf) when the trimmer potentiometer is mounted to the PCB. 3. Cleaning Isopropyl alcohol and ethyl alcohol are applicable solvents for cleaning. If you use any other types of solvents, please consult with a Murata factory representative prior to using. 7 Continued on the following page. 43 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 PV12/PV37/PV36 Series Notice Continued from the preceding page. c Soldering Profile Flow Soldering Profile Temperature (C) Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb) T3 T2 t2 Heating T1 Limit Profile Standard Profile Time (s) t1 Pre-heating Standard Profile Pre-heating Limit Profile Heating Heating Temp. (T1) Time (t1) Temp. (T2) Time (t2) C sec. C sec. Time C sec. C sec. Time 150 60 to 120 250 5 max. 1 150 60 to 120 260 3 max. 1 Series PV12 PV37 PV36 Pre-heating Cycle of Flow Temp. (T1) Time (t1) Temp. (T3) Time (t2) Cycle of Flow Soldering Iron Standard Condition Series Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output Cycle of Soldering Iron C sec. W Time 35010 3 max. 30 max. 1 PV12 PV37 PV36 c Notice (Handling) 7 1. Use suitable screwdrivers that fit comfortably in the driver slot. We recommend the screwdrivers below. * Recommended screwdriver for manual adjustment ENGINEER INC.: DA-40 (Murata P/N: KMDR180) We can supply the screwdrivers above. If you place an order, please specify the Murata P/N. 2. When adjusting with an adjustment tool, the applied force to the adjustment screw should not exceed 4.9N (Ref. 500gf). If excessive force is applied, the trimmer potentiometer may not function due to damage. c Notice (Other) 1. Please make sure that your product has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Murata cannot guarantee trimmer potentiometer integrity when used under conditions other than those specified in this document. 44 3. When using a lock paint to fix the slot position, please use adhesive resin without chlorine or sulfur (Three-bond "1401 series") and evaluate performance with your product. Lock paint may cause corrosion or electrical contact problems. R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 SMD Open Type (PVZ2/A2/Z3)/SMD Sealed Type (PVM4A_C01 Series) Specifications and Test Methods The tests and measurements should be conducted under the conditions of 15 to 35C of temperature, 25 to 75% of relative humidity and 86 to 106 kpa of atmospheric pressure unless otherwise specified. If questionable results occur that have been measured in accordance with the above-mentioned conditions, the tests and measurements should be conducted under the conditions of 252C of temperature, 45 to 55% of relative humidity and 86 to 106 kpa of atmospheric pressure. No. 1 Item Residual Resistance Test Methods Position the contact arm at the extreme counterclockwise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end terminal. Then, position the contact arm at the extreme clockwise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end terminal. During this test, take suitable precautions to ensure that the rated current of the resistance element is not exceeded. Contact resistance variation should be measured with the measuring circuit shown below, or its equivalent. The operating wiper should be rotated in both directions through 90% of the actual effective-electrical travel for a total of 6 cycles. The rate of rotation of the operating wiper should be such that the wiper completes 1 count in determining whether or not a contact resistance variation is observed at least twice in the same location. The test current should follow the value given in Table 2 unless otherwise limited by the power rating. 2 Contact Resistance * PVZ/PVA2 Standard Total Resistance R (ohm) 100VRF10k 10kVRF100k 100kVR #1 Test Current 20mA max. 1mA max. 100A max. * PVM4ApppC01 Standard Total Standard Total Test Test Resistance R Current Resistance R Current (ohm) (ohm) RV100 20mA 50kVRF200k 200A 100FRF500 10mA 200kVRF1M 100A 500VRF1k 4mA 1MVRF2M 50A 1kVRF2k 2mA 2MVR 30A 2kVRF50k 1mA Constant Current Source (Test current shown in Table 2) Rx Oscilloscope #3 #2 Calibration resistance AC Amplifier vertical entry Rx : Trimmer Potentiometer Oscilloscope bandwidth: 100Hz to 50kHz Figure 1: CRV measuring circuit Table 2: Test current for CRV 3 Humidity Exposure The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the potentiometer should be placed in a chamber at 402C and 90 - 95% without loading for 50012 hours. The resistance value should be measured after keeping the potentiometer in a room for 51/6 hours. 4 High Temperature Exposure The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the potentiometer should be placed in a chamber at 702C without loading for 50012 hours. The resistance value should be measured after keeping the potentiometer in a room for 1.51/6 hours. 5 Humidity Load Life The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the potentiometer should be placed in a chamber at 402C and 90 - 95% with loading the 1/2 rated voltage between #1 and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 100012 hours. The resistance value should be measured after keeping the potentiometer in a room for 51/6 hours. 6 Load Life The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the potentiometer should be placed in a chamber at 702C (502C for PVZ) with loading the 1/2 rated voltage between #1 and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 100012 hours. The resistance value should be measured after keeping the potentiometer in a room for 1 to 2 hours. The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the potentiometer should be subjected to Table 3, Table 4 temperature for 5 cycles. The resistance value should be measured after keeping the potentiometer in a room for 1 to 2 hours. 7 Temperature Cycle Sequence Temp. (C) Time (min.) 1 2 3 4 -253 +252 +853 +252 303 10 max. 303 10 max. Table 3: PVZ Sequence Temp. (C) Time (min.) 1 2 3 4 -553 +252 +1253 +252 303 10 max. 303 10 max. Table 4: PVA2/PVM4A---C01 The trimmer potentiometer should be subjected to each of the following temperatures (see Table 5, Table 6) for 30 to 40 minutes. The resistance value should be measured in the chamber. TCR= 8 Temperature Coefficient of Resistance R2 - R1 R1 (T2 - T1) Z 106 (ppm/C) T1 : Reference temperature in degrees celsius R1 : Resistance at reference temperature in ohm Sequence Temp. (C) 1* +252 2 -253 Table 5: PVZ Note*: Norm temp. 9 Rotational Life 3* +252 4 +853 T2 : Test temperature in degrees celsius R2 : Resistance at test temperature in ohm Sequence Temp. (C) 1* +252 2 -553 3* 4 +252 +1253 Table 6: PVA2/PVM4A---C01 The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles per minute, for 10 cycles continuously. The resistance value should be measured after keeping the potentiometer in a room for 105 minutes. 45 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 SMD Sealed Type (PVG3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods The following describes trimmer potentiometer testing conducted by Murata Manufacturing Co., Ltd. in accordance with MIL-R-22097 (military specification for variable resistors, non-wirewound) and MIL-STD-202 (test methods for electronic and electrical component parts). No. Item Test Methods Measure total resistance between the resistance element and terminals (#1 and #3) with the contact arm positioned against a stop. The positioning of the contact arm and terminal should be the same for subsequent total resistance measurements on the same device. Use the test voltage specified in Table 1 for total resistance measurements. This voltage should be used for all subsequent total resistance measurements. 1 Total Resistance Total Resistance, Nominal (ohm) 10VRV100 100FRV1k 1kFRV10k 10kFRV100k 100kFR Maximum Test Voltage (V) 1.0 3.0 10.0 30.0 100.0 Table 1: Total resistance test voltage 2 Residual Resistance Position the contact arm at the extreme counterclockwise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end terminal. Then, position the contact arm at the extreme clockwise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end terminal. During this test, take suitable precautions to ensure that the rated current of the resistance element is not exceeded. Contact resistance variation should be measured with the measuring circuit shown in Figure 1, or its equivalent. The adjustment rotor (screw) should be rotated in both directions through 90% of the actual effective-electrical rotational angle (number of turns) for a total of 6 cycles. Only the last 3 cycles should count in determining whether or not a contact resistance variation is observed at least twice in the same location, exclusive of the roll-on or roll-off points where the contact arm moves from the termination, on or off, the resistance element. The rate of rotation of the adjustment rotor (screw) should be such that the adjustment rotor (screw) completes 1 cycle for 5 seconds minimum to 2 minutes maximum. The test current used should follow the value given in Table 2 unless otherwise limited by power rating. 3 Contact Resistance Variation Standard Total Resistance R (ohm) RV100 100FRF500 500VRF1k 1kVRF2k 2kVRF50k 50kVRF200k 200kVRF1M 1MVRF2M 2MVR Test Current 20mA 10mA 4mA 2mA 1mA 200A 100A 50A 30A Rx #1 Oscilloscope #3 #2 Constant Current Source (Test current shown in Table 2) Calibration resistance AC Amplifier vertical entry Rx : Trimmer Potentiometer Oscilloscope bandwidth :100Hz to 50kHz Figure 1: CRV measuring circuit Table 2: Test current for CRV The trimmer potentiometer should be subjected to each of the following temperatures (see Table 3) for 30-45 minutes. Temperature coefficient of resistance should be applied to the following formula. TCR= 4 Temperature Coefficient of Resistance R2 - R1 Z 106 (ppm/C) R1 (T2 - T1) T1 T2 R1 R2 : Reference temperature in degrees celsius : Test temperature in degrees celsius : Resistance at reference temperature in ohm : Resistance at test temperature in ohm Sequence 1* 2 Temperature (C) +25 -15 3 Min. operating Temperature 4* 5 +25 +65 6 Max. operating Temperature Note*: Reference temperature Table 3: Test temperatures The wiper should be set at approximately 40% of the actual effective-electrical rotational angle (number of turns). An adequate DC test potential should be applied between terminal #1 and terminal #3. The voltage between terminal #1 and terminal #3, and the voltage between terminal #1 and terminal #2, should be measured and applied to the following formula. E 5 Voltage Setting Stability e' e Voltage setting stability= -- - -- Z100 (%) E E ( ) e : Before test (The voltage between terminal #1 and terminal #2) e' : After test (The voltage between terminal #1 and terminal #2) #1 #3 #2 e Figure 2 Continued on the following page. 46 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 SMD Sealed Type (PVG3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods Continued from the preceding page. No. Item Test Methods The trimmer potentiometer should be subjected to Table 4 temperature for 5 cycles. The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for 1-2 hours. 6 Temperature Cycle Sequence 1 Temp. (C) PV-- series -553 Time (min.) 30 2 3 4 +252 +1253 +252 5 max. 30 5 max. Table 4: One cycle of temperature cycle. 1) PV12, PV32, PVM4A---D01 series The trimmer potentiometer should be placed in a chamber at a temperature of 402C and a humidity of 90-95% without loading for 2508 hours (50012 hours for PVM4A---D01 series). The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for 51/6 hours. 2) PVG3, PVG5, PV36, PV37 series The trimmer potentiometer should be subjected to the programmed humidity environment for 10 cycle (see Figure 3). The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for 1.51/2 hours. MIL-STD-202 METHOD 106 80-98%RH 70 65 60 55 Humidity TEMPERATURE (DEGREES CELSIUS) 7 40 90-98%RH 90-98%RH 24 HOURS RATE OF CHANGE OF TEMPERATURE IS UNSPECIFIED. HOWEVER, SPECIMENS SHOULD NOT BE SUBJECTED TO RADIANT HEAT FROM CHAMBER-CONDITIONING PROCESSES 50 45 80-98%RH 90-98%RH INITIAL CONDITIONING IN A DRY OVEN HUMIDITY UNCONTROLLED 35 30 +10C -2C CIRCULATION OF CONDITIONING AIR SHOULD BE AT A MINIMUM CUBIC RATE PER MINUTE EQUIVALENT TO 5 TIMES THE VOLUME OF THE CHAMBER 25 20 15 INITIAL MEASUREMENTS AS SPECIFIED IN 3.2 10 5 0 -5 -10 END OF FINAL CYCLE MEASUREMENTS AS SPECIFIED IN 3.6 VOLTAGE APPLIED AS SPECIFIED IN 3.5 UNLESS OTHERWISE SPECIFIED TEMPERATURE TOLERANCE IS, 2C AT ALL POINTS WITHIN THE CHAMBER EXCEPT THE IMMEDIATE VICINITY OF THE SPECIMENS AND THE CHAMBER SURFACES PRIOR TO FIRST CYCLE STEP 1 UNLESS OTHERWISE SPECIFIED STEPS 7a AND 7b PERFORMED DURING ANY 5 OF THE FIRST 9 CYCLES. HUMIDITY UNCONTROLLED DURING STEPS 7a AND 7b ONLY STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7b STEP 7a STEP 7 ONE CYCLE 24 HOURS. REPEAT AS SPECIFIED IN 3.3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Figure 3 8 9 Vibration 1) PV-- series The trimmer potentiometer should be vibrated throughout the frequency range at the 20G level. A complete frequency range, 10Hz to 2000Hz and back, should be made within 15 minutes for a total of 4 sweeps in each of the three axis directions for a total of 12 sweeps. Shock 1) PV-- series The trimmer potentiometer should be shocked at the 100G level and should be subjected to 4 shocks in each of the three axis directions for a total of 12 shocks. 2) PVM4A---D01 series The trimmer potentiometer should be shocked at the 100G level and should be subjected to 3 shocks in each of the six axis directions for a total of 18 shocks. 10 Temperature Load Life Full rated continuous working voltage not exceeding the maximum rated voltage should be applied intermittently between terminal #1 and terminal #3 of the trimmer potentiometer, 1.5 hours on and 0.5 hours off, for a total of 100012 hours, at a temperature of 702C (852C for PV37 series). The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for 1 to 2 hours. 11 High Temperature Exposure The trimmer potentiometer should be placed in a chamber at a temperature of 1253C 2508 hours without loading. The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for 1 to 2 hours. Low Temperature Exposure 12 (Except for PVM4A---D01) The trimmer potentiometer should be placed in a chamber at a temperature of -553C for 1 hours without loading. Full rated continuous working voltage not exceeding the maximum rated voltage should be applied for 45 minutes. The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for approximately 24 hours. 13 Low Temperature Operation (Only for PVM4A---D01) The trimmer potentiometer should be placed in a chamber at a temperature of -253C (-553C for PVM4A---D01 series) 484 hours without loading. The trimmer potentiometer should be removed from the chamber, and maintained at a temperature of 255C for 1-2 hours. Continued on the following page. 47 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. SMD Sealed Type (PVG3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods Continued from the preceding page. No. Item Test Methods 1)PV-- series Full rated continuous working voltage not exceeding the maximum rated voltage should be applied with the circuit shown in the figure. The adjustment rotor (screw) should be continuously cycled through not less than 90% of effective-electrical rotational angle (number of turns), at the rate of 1 cycle for 5 seconds minimum to 2.5 minutes maximum for total of 200 cycles. End Terminal Resistor 1 End Terminal End Terminal Resistor 2 End Terminal 14 Rotational Life DC supply Figure 4 2) PVG3, PVG5 series The adjustment rotor (screw) should be continuously cycled though not less than 90% of effective-electrical rotational angle (number of turns), at the rate of 1 cycle for 5 seconds minimum to 2.5 minutes maximum for a total of 50 (100 for PVG5) cycles, without loading. 3) PVM4A---D01 series The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles per minute, for 100 cycles continuously. 48 R50E.pdf Jul.23,2012 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Packaging c Minimum Quantity Minimum Quantity (pcs.) Part Number o180mm reel Bulk PVZ2A 3000 1000 PVZ2R 3000 1000 PVA2 3000 1000 PVZ3A/H 2000 1000 PVZ3G 2500 1000 PVZ3K 1500 1000 PVG3A/G 1000 500 PVM4 500 500 PVG5A 250 100 PVG5H 500 100 PV32 -- 100 PV12 -- 50 PV36 -- 100 PV37 -- 100 c Dimensions of Reel PVZ2A/PVA2/PVZ3A/PVZ3G/PVZ3H PVZ2R/PVZ3K/PVM4/PVG3/PVG5H 2.0o0.5 21.0o0.8 Dia. 50 min. 13.0o0.5 Dia. 50 min. 13.0o0.5 Dia. 2.0o0.5 21.0o0.8 Dia. 9.0o1.0 13.0o1.0 13.0o1.0 178o2 Dia. 17.0o1.0 178o2 Dia. (in mm) (in mm) PVG5A 50 Dia. min. 13.00.5 Dia. 2.00.5 21.00.8 Dia. 17.01.0 19.41.0 178.02.0 Dia. (in mm) Continued on the following page. 49 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Packaging Continued from the preceding page. c Dimensions of Plastic Tape PVZ2 / PVA2 / PVZ3 2.00.1 4.00.1 a 1.5 +0.1 -0 Dia. 4.00.1 I J 1.750.1 D C B A a' Across a - a' Tape feeding direction Part Number A PVZ2A PVZ2R 2.40.2 C D I J 8.00.2 3.50.1 1.10.1 0.20.1 5.10.2 12.00.2 5.50.1 1.00.1 0.30.1 3.10.1 PVA2 PVZ3A/H PVZ3G B 3.10.1 1.10.1 8.00.2 3.80.2 3.30.2 0.20.1 1.30.1 5.80.2 PVZ3K 1.950.1 3.50.1 12.00.2 2.30.1 5.50.1 0.30.1 s 4HE SIDE CONTAINING TERMINALS AND FACES THE PLASTIC TAPE PILOT HOLES (in mm) c Dimensions of Plastic Tape 5.50.1 4.00.1 1.5 +0.1 n $IA A B Ag I J 12.00.2 2.00.1 8.00.1 1.750.1 PVG3A / PVG3G / PVM4 / PVG5H !CROSS A n Ag A 4APE FEEDING DIRECTION Part Number PVG3A PVG3G A 4.00.1 B 4.00.1 4.90.1 I J 2.10.1 0.30.1 PVM4 4.50.2 5.50.2 2.150.1 0.30.1 PVG5H 5.40.2 5.80.2 4.00.1 0.40.1 s 4HE SIDE CONTAINING TERMINALS AND FACES THE PLASTIC TAPE PILOT HOLES EXCEPT 06' (in mm) Continued on the following page. 50 !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. R50E.pdf Jul.23,2012 Packaging Continued from the preceding page. c Dimensions of Plastic Tape PVG5A 7.50.1 B I J 16.00.3 4.00.1 1.5 +0.1 -0 Dia. a 1.750.1 2.00.1 12.00.2 Across a - a' a' A Tape feeding direction Part Number PVG5A A B I J 4.30.2 5.40.2 5.40.1 0.40.1 (in mm) 51 R50E.pdf !Note * Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. * This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Jul.23,2012 Recommended Adjustment Tools/Qualified Standards c Recommended Adjustment Tools Model Number MURATA Model Number Blade PVZ2/PVA2 MURATA MFG. KMDR190 KMDR190 + Cross PVZ3G VESSEL MFG. No.9000+1.7Z30 KMDR080 + Cross SA-2225 KMDR070 - Minus (round edge) Trimmer Potentiometer Series PVZ3A/PVZ3H/PVG3 Manufacturers TORAY INDUSTRIES, INC. PVM4 VESSEL MFG. No.9000-2.6Z30 KMDR120 - Minus PVG5 VESSEL MFG. No.9000-1.3Z30 KMDR130 - Minus others VESSEL MFG. No.9000-1.8Z30 KMDR110 - Minus Model Number MURATA Model Number Blade JB-2225 KMBT070 - Minus (round edge) For Automatic Adjustment Trimmer Potentiometer Series PVZ3 PVG3 Manufacturers TORAY INDUSTRIES, INC c Qualified Standards The products listed here have been produced by the ISO9001 and ISO/TS16949 certified factory. MURATA FACTORY Qualified Date Standard Qualified Number Wuxi Murata Electronics Co.,Ltd. May 12, 1999 UNDERWRITERS LABORATORIES INC. A7924 * No ODCs (Ozone Depleting Chemicals) are used on all Murata's trimmer potentiometers. 52