Ordering information Three phase input type TAH series TAH -10 -683 1 2 -O 3 4 1Model Name 2Rated Current 3Line to ground capacitor code:See table 1.1. table1.1 Line to ground capacitor code Code 683 Line to ground Leakage Current capacitor (Input 250/500V 60Hz) (nominal value) 2.5mA/5.0mA max 68000pF 4Options D :DIN rail installation type * The dimensions change when the option is set. Refer to External view. The terminal cover is retracted inside the unit DIN rail installation type is option Features of TAH series Ultra high-attenuation type of common mode noise from 10kHz to 1MHz - Three Phase 500 VAC - Quick and easy push-down terminal Just connect the wires, push down and tighten the screws with a screwdriver Specifications No. Items TAH-04-683 1 Rated Voltage[V] AC Three Phase 500 2 Rated Current[A] 4 3 Test Voltage (Terminal-Mounting Plate) 2,000 VAC (Cutoff Current = 100mA), 1minute at room temperature and humidity 4 Isolation Resistance (Terminal-Mounting Plate) 500 VDC 100MW minute at room temperature and humidity 5 Leakage current 250/500V 60Hz 2.5mA/5.0mA max 6 Voltage drop 1.5V max 7 Safety agency approval temperatures -25 to +85C (Refer to Derating Curve) 8 Operating temperature -40 to +85C (Refer to Derating Curve) 9 Operating humidity 20 to 95%RH (Non condensing) 10 Storage temperature/humidity -40 to +85C/20 to 95%RH (Non condensing) 11 Vibration 10 to 55Hz, 19.6m/s2(2G), 3min. Period, 1hour each X, Y and Z axis 12 Impact 196.1m/s2(20G), 11ms Once each X, Y and Z axis 13 Safety agency approvals UL1283, CSA C22.2 No.8 (C-UL) , DIN EN133200 VDE0565 Teil3-1, ENEC 14 Case size (without projection) /Mass 63X64X128 mm (WXHXD) /620g max (Option : -D refer to external view) Circuit Diagram TAH-06-683 6 TAH-10-683 TAH-20-683 TAH-30-683 10 20 30 1.0V max Derating Curve Case LOAD 1 4 2 5 3 6 Noise Filter CY CY CY : Line to ground capacitor I-12 : Mounting Plate 100 Load Factor [%] LINE 80 60 40 20 0 -40 -30 -20 40 50 60 70 Ambient Temperature [C] 80 90 TAC,TAH series External view This product is shipped in the following condition, because it is equipped with push-down terminals. 1The terminal cover is retracted inside the unit. 2The screws for connecting the terminals are held in the up right position. Standard Type Mounting Plate 128 (2.5) 118 0.5 Output Terminal Output Terminal 12 Name Plate Input Terminal 20 63 83.5 19 50 Protection Earth 50 0.5 Input Terminal Output Terminal Terminal cover 4-f5.5 Mounting Hole (2) 7-M4 Terminal cover Tolerance : 1 Mass : 620g or less Mounting Plate : Iron (surface finishing:nickel plating) t=1.0 Case : PBT Dimensions in mm Terminal block screw tighting torque M4:1.6N-m (16.9kgf-cm) max 64 Closed the terminal cover DIN rail installation Type Mounting Plate 10 (11) 108 Input Terminal (2.5) 83.5 50 20 Protection Earth Output Terminal 63 Name Plate Input Terminal 12 19 Output Terminal Output Terminal Terminal cover 7-M4 (2) Terminal cover DIN rail Note when installing the noise filter on a DIN rail. When the noise filter is grounded through the DIN rail, the proper noise attenuation may not be achieved. Be sure to connect the protection earth (PE) of the noise filter body to the earth. Tolerance : 1 Mass : 620g or less Mounting Plate : Iron (surface finishing:nickel plating) t=1.0 Case : PBT Dimensions in mm Terminal block screw tighting torque M4:1.6N-m (16.9kgf-cm) max 7 (9) 64 Closed the terminal cover DIN rail Name Plate Noise Filter I-13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cosel: TAH-04-683 TAH-04-683-D TAH-30-683 TAH-30-683-D TAH-06-683 TAH-06-683-D TAH-10-683 TAH-10-683-D TAH-20-683 TAH-20-683-D