I-12
Noise
Filter
Specifications
No. Items TAH-04-683 TAH-06-683 TAH-10-683 TAH-20-683 TAH-30-683
1 Rated Voltage[V] AC Three Phase 500
2 Rated Current[A] 46102030
3 Test Voltage (Terminal-Mounting Plate) 2,000 VAC (Cutoff Current = 100mA), 1minute at room temperature and humidity
4 Isolation Resistance (Terminal-Mounting Plate) 500 VDC 100MW minute at room temperature and humidity
5 Leakage current 250/500V 60Hz 2.5mA/5.0mA max
6 Voltage drop 1.5V max 1.0V max
7 Safety agency approval temperatures -25 to +85C (Refer to Derating Curve)
8 Operating temperature -40 to +85C (Refer to Derating Curve)
9 Operating humidity 20 to 95%RH (Non condensing)
10 Storage temperature/humidity -40 to +85C/20 to 95%RH (Non condensing)
11 Vibration 10 to 55Hz, 19.6m/s2(2G), 3min. Period, 1hour each X, Y and Z axis
12 Impact 196.1m/s2(20G), 11ms Once each X, Y and Z axis
13 Safety agency approvals UL1283, CSA C22.2 No.8 (C-UL) , DIN EN133200 VDE0565 Teil3-1, ENEC
14 Case size (without projection) /Mass 63X64X128 mm (WXHXD) /620g max (Option : -D refer to external view)
TAH series
Three phase input type
TAH -10 -683 -O
Ordering information
1Model Name
2Rated Current
3Line to ground capacitor code:See table 1.1.
table1.1 Line to ground capacitor code
Code Leakage Current
(Input 250/500V 60Hz)
Line to ground
capacitor
(nominal value)
683 2.5mA/5.0mA max 68000pF
4Options
D :DIN rail installation type
1 2 3 4
Features of TAH series
Circuit Diagram Derating Curve
Ambient Temperature [C]
Load Factor [%]
70 80 90-20 40 50 60
20
0
-40 -30
100
80
60
40
Ultra high-attenuation type of common mode noise from 10kHz to 1MHz
- Three Phase 500 VAC - Quick and easy push-down terminal
Just connect the wires, push down and tighten
the screws with a screwdriver
*
The dimensions change when the option is set.
Refer to External view.
LOAD
Case
LINE
4
5
6
1
2
3
CY : Line to ground capacitor
CY
CY
: Mounting Plate
DIN rail installation type is optionThe terminal cover is retracted inside the unit
I-13
Noise
Filter
TAC,TAH series
External view
4-f5.5Terminal cover
7-M4
Mounting Hole
Protection Earth
64
12
19
20
63
50±0.5
83.5
128
118±0.5
(2)
Terminal cover
Input
Terminal
Input
Terminal
Output
Terminal
Output
Terminal
Output
Terminal
Mounting Plate
Name Plate
¶ Tolerance : ±1
¶ Mass : 620g or less
¶ Mounting Plate : Iron (surface finishing:nickel plating) t=1.0
¶ Case : PBT
¶ Dimensions in mm
¶ Terminal block screw tighting torque M4:1.6N-m (16.9kgf-cm) max
¶ Closed the terminal cover
50
(2.5)
This product is shipped in the following condition, because it is equipped with push-down terminals.
1The terminal cover is retracted inside the unit.
2The screws for connecting the terminals are held in the up right position.
¡Note when installing the noise
fi lter on a DIN rail.
When the noise fi lter is grounded through the
DIN rail, the proper noise attenuation may not be
achieved.
Be sure to connect the protection earth (PE) of
the noise fi lter body to the earth.
DIN rail
7-M4
Mounting Plate
Protection Earth
(11)
108
7
(9)
12
19
20
83.5
(2)
64
63
Terminal cover
Terminal cover
Input
Terminal
Input
Terminal
Output
Terminal
Output
Terminal
Output
Terminal
¶ Tolerance : ±1
¶ Mass : 620g or less
¶ Mounting Plate : Iron (surface finishing:nickel plating) t=1.0
¶ Case : PBT
¶ Dimensions in mm
¶ Terminal block screw tighting torque M4:1.6N-m (16.9kgf-cm) max
Name Plate
¶ Closed the terminal cover
50
(2.5)
10
Standard Type
DIN rail installation Type
Name Plate
DIN rail
