MC14504B Hex Level Shifter for TTL to CMOS or CMOS to CMOS The MC14504B is a hex non-inverting level shifter using CMOS technology. The level shifter will shift a TTL signal to CMOS logic levels for any CMOS supply voltage between 5 and 15 volts. A control input also allows interface from CMOS to CMOS at one logic level to another logic level: Either up or down level translating is accomplished by selection of power supply levels VDD and VCC. The VCC level sets the input signal levels while VDD selects the output voltage levels. http://onsemi.com MARKING DIAGRAMS PDIP-16 P SUFFIX CASE 648 Features * UP Translates from a Low to a High Voltage or DOWN Translates * * * * * * from a High to a Low Voltage Input Threshold Can Be Shifted for TTL Compatibility No Sequencing Required on Power Supplies or Inputs for Power Up or Power Down 3 to 18 Vdc Operation for VDD and VCC Diode Protected Inputs to VSS Capable of Driving Two Low-Power TTL Loads or One Low-Power Schottky TTL Load Over the Rated Temperature Range These Devices are Pb-Free and are RoHS Compliant Parameter Value Unit VCC DC Supply Voltage Range -0.5 to +18.0 V VDD DC Supply Voltage Range -0.5 to +18.0 V Vin Input Voltage Range (DC or Transient) -0.5 to +18.0 V Vout Output Voltage Range (DC or Transient) -0.5 to VDD + 0.5 V Input or Output Current (DC or Transient) per Pin 10 mA PD Power Dissipation, per Package (Note 1) 500 mW Iin, Iout TA Ambient Temperature Range -55 to +125 C Tstg Storage Temperature Range -65 to +150 C TL Lead Temperature (8-Second Soldering) 260 C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/_C From 65_C To 125_C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS v (Vin or Vout) v VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open. (c) Semiconductor Components Industries, LLC, 2011 June, 2011 - Rev. 7 1 MC14504BCP AWLYYWWG 1 16 SOIC-16 D SUFFIX CASE 751B 14504BG AWLYWW 1 16 TSSOP-16 DT SUFFIX CASE 948F MAXIMUM RATINGS (Voltages Referenced to VSS) Symbol 16 14 504B ALYWG G 1 16 SOEIAJ-16 F SUFFIX CASE 966 MC14504B ALYWG 1 A WL, L YY, Y WW, W G or G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Indicator (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. Publication Order Number: MC14504B/D MC14504B PIN ASSIGNMENT VCC 1 16 VDD Aout 2 15 Fout Ain 3 14 Fin Bout 4 13 MODE Bin 5 12 Eout Cout 6 11 Ein Cin 7 10 Dout VSS 8 9 Din LOGIC DIAGRAM VCC VDD LEVEL SHIFTER INPUT OUTPUT TTL/CMOS MODE SELECT MODE Mode Select Input Logic Levels Output Logic Levels 1 (VCC) TTL CMOS 0 (VSS) CMOS CMOS 1/6 of package shown. ORDERING INFORMATION Package Shipping MC14504BCPG PDIP-16 (Pb-Free) 500 Units / Rail MC14504BDG SOIC-16 (Pb-Free) 48 Units / Rail MC14504BDR2G SOIC-16 (Pb-Free) 2500 Units / Tape & Reel MC14504BDTG TSSOP-16* 96 Units / Rail MC14504BDTR2G TSSOP-16* 2500 Units / Tape & Reel MC14504BFG SOEIAJ-16 50 Units / Rail MC14504BFELG SOEIAJ-16 2000 Units / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 2 MC14504B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIII IIII IIIIII IIIIIIIII IIIIII IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III III IIIIIIIIIIIIIIIIIIIII IIIIII IIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIII III II III III III IIII III II III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) - 55_C 25_C 125_C VCC Vdc VDD Vdc Min Max Min Typ (Note 2) Max Min Max Unit VOL - - - 5.0 10 15 - - - 0.05 0.05 0.05 - - - 0 0 0 0.05 0.05 0.05 - - - 0.05 0.05 0.05 Vdc VOH - - - 5.0 10 15 4.95 9.95 14.95 - - - 4.95 9.95 14.95 5.0 10 15 - - - 4.95 9.95 14.95 - - - Vdc 5.0 5.0 5.0 5.0 10 10 15 10 15 15 - - - - - 0.8 0.8 1.5 1.5 3.0 - - - - - 1.3 1.3 2.25 2.25 4.5 0.8 0.8 1.5 1.5 3.0 - - - - - 0.8 0.8 1.4 1.5 2.9 5.0 5.0 5.0 5.0 10 10 15 10 15 15 2.0 2.0 3.6 3.6 7.1 - - - - - 2.0 2.0 3.5 3.5 7.0 1.5 1.5 2.75 2.75 5.5 - - - - - 2.0 2.0 3.5 3.5 7.0 - - - - - - - - - 5.0 5.0 10 15 - 3.0 - 0.64 - 1.6 - 4.2 - - - - - 2.4 - 0.51 - 1.3 - 3.4 - 4.2 - 0.88 - 2.25 - 8.8 - - - - - 1.7 - 0.36 - 0.9 - 2.4 - - - - IOL - - - 5.0 10 15 0.64 1.6 4.2 - - - 0.51 1.3 3.4 0.88 2.25 8.8 - - - 0.36 0.9 2.4 - - - mAdc Input Current Iin - 15 - 0.1 - 0.00001 0.1 - 1.0 mAdc Input Capacitance (Vin = 0) Cin - - - - - 5.0 7.5 - - pF IDD or ICC - - - 5.0 10 15 - - - 0.05 0.10 0.20 - - - 0.0005 0.0010 0.0015 0.05 0.10 0.20 - - - 1.5 3.0 6.0 mAdc Quiescent Current (Per Package) TTL-CMOS Mode IDD 5.0 5.0 5.0 5.0 10 15 - - - 0.5 1.0 2.0 - - - 0.0005 0.0010 0.0015 0.5 1.0 2.0 - - - 3.8 7.5 15 mAdc Quiescent Current (Per Package) TTL-CMOS Mode ICC 5.0 5.0 5.0 5.0 10 15 - - - 5.0 5.0 5.0 - - - 2.5 2.5 2.5 5.0 5.0 5.0 - - - 6.0 6.0 6.0 mAdc Characteristic Output Voltage Vin = 0 V Vin = VCC Symbol "0" Level "1" Level Input Voltage "0" Level (VOL = 1.0 Vdc) TTL-CMOS (VOL = 1.5 Vdc) TTL-CMOS (VOL = 1.0 Vdc) CMOS-CMOS (VOL = 1.5 Vdc) CMOS-CMOS (VOL = 1.5 Vdc) CMOS-CMOS VIL Input Voltage "1" Level (VOH = 9.0 Vdc) TTL-CMOS (VOH = 13.5 Vdc) TTL-CMOS (VOH = 9.0 Vdc) CMOS-CMOS (VOH = 13.5 Vdc) CMOS-CMOS (VOH = 13.5 Vdc) CMOS-CMOS VIH Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) IOH (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Quiescent Current (Per Package) CMOS-CMOS Mode Source Sink 2. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. http://onsemi.com 3 Vdc Vdc mAdc MC14504B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII III IIII III IIIIIIIIII IIIII IIIIII III IIII III IIII III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIII III IIIIII III IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIII III IIIIII III IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIII IIIIIII IIIIIII IIIIIII IIIIIII IIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII SWITCHING CHARACTERISTICS (CL = 50 pF, TA = 25_C) Characteristic Propagation Delay, High to Low Symbol Shifting Mode VCC Vdc VDD Vdc Min Limits Typ (Note 3) Max Unit tPHL TTL - CMOS VDD > VCC 5.0 5.0 10 15 - - 140 140 280 280 ns CMOS - CMOS VDD > VCC 5.0 5.0 10 10 15 15 5.0 5.0 10 15 15 5.0 5.0 10 10 15 - - - - - - - - 120 120 70 185 185 175 170 160 240 240 140 370 370 350 340 320 5.0 5.0 10 10 15 15 - - - 10 15 15 5.0 5.0 10 5.0 10 15 - - - - - - - - - 170 170 100 275 275 145 100 50 40 340 340 200 550 550 290 200 100 80 CMOS - CMOS VCC > VDD Propagation Delay, Low to High tPLH TTL - CMOS VDD > VCC CMOS - CMOS VDD > VCC CMOS - CMOS VCC > VDD Output Rise and Fall Time tTLH, tTHL ALL ns ns 3. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 7 VSp , INPUT SWITCHPOINT VOLTAGE (Vdc) VSp , INPUT SWITCHPOINT VOLTAGE (Vdc) 7 6 VCC = 10 V 5 4 3 VCC = 5 V 2 1 6 5 4 3 2 1 0 0 0 5 10 15 VDD, SUPPLY VOLTAGE (Vdc) 20 0 Figure 1. Input Switchpoint CMOS to CMOS Mode 20 20 EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE EEEEEEEEE 15 10 5 5 10 15 VDD, SUPPLY VOLTAGE (Vdc) 20 Figure 2. Input Switchpoint TTL to CMOS Mode VDD, SUPPLY VOLTAGE (Vdc) VDD, SUPPLY VOLTAGE (Vdc) VCC = 5 V EE EE EE EE EE EE EE EE 15 10 0 5 0 0 5 10 15 VCC, SUPPLY VOLTAGE (Vdc) 20 0 Figure 3. Operating Boundary CMOS to CMOS Mode 5 10 15 VCC, SUPPLY VOLTAGE (Vdc) 20 Figure 4. Operating Boundary TTL to CMOS Mode http://onsemi.com 4 MC14504B PACKAGE DIMENSIONS PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A- 16 9 1 8 B F C L DIM A B C D F G H J K L M S S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 SOEIAJ-16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966-01 ISSUE A 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 9 Q1 E HE 1 M_ L 8 Z DETAIL P D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) http://onsemi.com 5 DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.031 MC14504B PACKAGE DIMENSIONS TSSOP-16 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948F-01 ISSUE B 16X K REF 0.10 (0.004) 0.15 (0.006) T U T U M S V S CCC CCC EEE CCC EEE K S K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. N 8 1 0.25 (0.010) M 0.15 (0.006) T U S A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS http://onsemi.com 6 MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC14504B PACKAGE DIMENSIONS SOIC-16 D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE K -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C -T- SEATING PLANE J M D DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 16 PL 0.25 (0.010) M T B S A S SOLDERING FOOTPRINT 8X 6.40 16X 1 1.12 16 16X 0.58 1.27 PITCH 8 9 DIMENSIONS: MILLIMETERS ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC14504B/D