Order this document by MOC5007/D SEMICONDUCTOR TECHNICAL DATA [IF(on) = 1.6 mA Max] GlobalOptoisolator [IF(on) = 4 mA Max] [IF(on) = 10 mA Max] The MOC5007, MOC5008 and MOC5009 have a gallium arsenide IRED optically coupled to a high-speed integrated detector with Schmitt trigger output. Ideal for applications requiring electrical isolation, fast response time, noise immunity and digital logic compatibility. * * * * * * *Motorola Preferred Device Guaranteed Switching Times -- ton, toff 4 < s Built-In ON/OFF Threshold Hysteresis High Data Rate, 1 MHz Typical (NRZ) Wide Supply Voltage Capability Microprocessor Compatible Drive To order devices that are tested and marked per VDE 0884 requirements, the suffix "V" must be included at end of part number. VDE 0884 is a test option. Applications * Interfacing Computer Terminals to Peripheral Equipment * Digital Control of Power Supplies * Line Receiver -- Eliminates Noise * Digital Control of Motors and Other Servo Machine Applications * Logic to Logic Isolator * Logic Level Shifter -- Couples TTL to CMOS Symbol 6 1 STANDARD THRU HOLE CASE 730A-04 SCHEMATIC MAXIMUM RATINGS (TA = 25C unless otherwise noted) Rating STYLE 5 PLASTIC Value Unit 1 6 2 5 3 4 INPUT LED Reverse Voltage VR 6 Volts Forward Current -- Continuous Forward Current -- Peak Pulse Width = 300 s, 2% Duty Cycle IF 60 1.2 mA Amp LED Power Dissipation @ TA = 25C Derate above 25C PD 120 1.41 mW mW/C Output Voltage Range Vo 0 -16 Volts Supply Voltage Range VCC 3 -16 Volts OUTPUT DETECTOR Output Current IO 50 mA Detector Power Dissipation @ TA = 25C Derate above 25C PD 150 1.76 mW mW/C Total Device Power Dissipation @ TA = 25C Derate above 25C PD 250 2.94 mW mW/C Maximum Operating Temperature(2) TA - 40 to + 85 C Tstg - 55 to +150 C TL 260 C PIN 1. 2. 3. 4. ANODE CATHODE NC OPEN COLLECTOR OUTPUT 5. GROUND 6. VCC TOTAL DEVICE Storage Temperature Range(2) Soldering Temperature (10 s) Isolation Surge Voltage(1) VISO 7500 Vac(pk) (Peak ac Voltage, 60 Hz, 1 Second Duration) 1. Isolation surge voltage is an internal device dielectric breakdown rating. 1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc. REV 1 Optoelectronics Device Data Motorola Motorola, Inc. 1995 1 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted)(1) Symbol Min Typ1) Max Unit Reverse Leakage Current (VR = 3 V, RL = 1 M) IR -- 0.05 10 A Forward Voltage (IF = 10 mA) Forward Voltage (IF = 0.3 mA) VF -- 0.75 1.2 0.95 1.5 -- Volts Capacitance (VR = 0 V, f = 1 MHz) C -- 18 -- pF VCC 3 -- 15 Volts ICC(off) -- 1 5 mA IOH -- -- 100 A ICC(on) -- 1.6 5 mA VOL -- 0.2 0.4 Volts Characteristic INPUT LED OUTPUT DETECTOR Operating Voltage Supply Current (IF = 0, VCC = 5 V) Output Current, High (IF = 0, VCC = Vo = 15 V) COUPLED Supply Current (IF = IF(on), VCC = 5 V) Output Voltage, Low (RL = 270 , VCC = 5 V, IF = IF(on)) Threshold Current, ON (RL = 270 , VCC = 5 V) MOC5007 MOC5008 MOC5009 IF(on) -- -- -- 1.2 -- -- 1.6 4 10 mA Threshold Current, OFF (RL = 270 , VCC = 5 V) MOC5007 MOC5008, 5009 IF(off) 0.3 0.3 0.75 -- -- -- mA Hysteresis Ratio (RL = 270 , VCC = 5 V) IF(off) IF(on) 0.5 0.75 0.9 Isolation Voltage(2) 60 Hz, AC Peak, 1 second, TA = 25C VISO 7500 -- -- Vac(pk) ton -- 1.2 4 s tf -- 0.1 -- toff -- 1.2 4 tr -- 0.1 -- Turn-On Time Fall Time Turn-Off Time Rise Time RL = 270 (3) VCC = 5 V, IF = IF(on) TA = 25C 1. Always design to the specified minimum/maximum electrical limits (where applicable). 2. For this test, IRED Pins 1 and 2 are common and Output Gate Pins 4, 5, 6 are common. 3. RL value effect on switching time is negligible. ICC 5V IF 1 6 RL 4 Vin tr = tf = 0.01 s Z = 50 2 270 VO (OPEN COLLECTOR OUTPUT) 5 IF (on) toff ton Vo tf tr Figure 1. Switching Test Circuit 2 Motorola Optoelectronics Device Data VO, OUTPUT VOLTAGE (VOLTS) TYPICAL CHARACTERISTICS 6 VOH 5 4 IF(off) 3 IF(on) RL = 270 VCC = 5 V TA = 25C 2 1 VOL 0 0 0.75 1 IF, INPUT CURRENT (mA) 2 IF(on), IF(off), THRESHOLD CURRENT (NORMALIZED) IF, THRESHOLD CURRENT (NORMALIZED) Figure 2. Transfer Characteristics for MOC5007 1.6 1.4 TURN ON THRESHOLD 1.2 1 TURN OFF THRESHOLD 0.8 0.6 IF NORMALIZED TO IF(on) AT VCC = 5 V TA = 25C 0.4 0 2 4 6 8 10 12 VCC, SUPPLY VOLTAGE (VOLTS) 14 1.6 1.4 1.2 1 0.8 NORMALIZED TO VCC = 5 V TA = 25C 0.6 -50 0 25 50 TA, TEMPERATURE (C) 75 100 Figure 4. Threshold Current versus Temperature 1 TA = 0C 25C 70C 0.5 6 IC , SUPPLY CURRENT (mA) VOL , OUTPUT VOLTAGE, LOW (VOLTS) Figure 3. Threshold Current versus Supply Voltage -25 0.2 0.1 0.05 0.02 1 2 5 10 20 IO, LOAD CURRENT (mA) 50 100 Figure 5. Output Voltage, Low versus Load Current Motorola Optoelectronics Device Data IF = 5 mA 4 0C 25C 70C 2 0 0 2 4 IF = 0 mA 6 8 10 12 VCC, SUPPLY VOLTAGE (VOLTS) 14 16 Figure 6. Supply Current versus Supply Voltage 3 PACKAGE DIMENSIONS -A- 6 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. -B- 1 STYLE 5: PIN 1. 2. 3. 4. 5. 6. 3 F 4 PL C N -T- L ANODE CATHODE NC OUTPUT GROUND VCC DIM A B C D E F G J K L M N K SEATING PLANE J 6 PL 0.13 (0.005) G M E 6 PL D 6 PL 0.13 (0.005) M T A M B M T B M A M M INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.300 BSC 0_ 15 _ 0.015 0.100 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 7.62 BSC 0_ 15 _ 0.38 2.54 CASE 730A-04 ISSUE G -A- 6 4 -B- 1 S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3 F 4 PL L H C -T- G J K 6 PL E 6 PL 0.13 (0.005) D 6 PL 0.13 (0.005) M T A M B M SEATING PLANE T B M A M CASE 730C-04 ISSUE D 4 M DIM A B C D E F G H J K L S INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.020 0.025 0.008 0.012 0.006 0.035 0.320 BSC 0.332 0.390 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.51 0.63 0.20 0.30 0.16 0.88 8.13 BSC 8.43 9.90 *Consult factory for leadform option availability Motorola Optoelectronics Device Data NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. -A- 6 4 -B- 1 3 L N F 4 PL C -T- SEATING PLANE G J K DIM A B C D E F G J K L N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.400 0.425 0.015 0.040 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 10.16 10.80 0.38 1.02 D 6 PL E 6 PL 0.13 (0.005) M T A M B M *Consult factory for leadform option availability CASE 730D-05 ISSUE D Motorola Optoelectronics Device Data 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 CODELINE TO BE PLACED HERE *MOC5007/D* Motorola OptoelectronicsMOC5007/D Device Data