LMC6061 LMC6061 Precision CMOS Single Micropower Operational Amplifier Literature Number: SNOS648C LMC6061 Precision CMOS Single Micropower Operational Amplifier General Description The LMC6061 is a precision single low offset voltage, micropower operational amplifier, capable of precision single supply operation. Performance characteristics include ultra low input bias current, high voltage gain, rail-to-rail output swing, and an input common mode voltage range that includes ground. These features, plus its low power consumption, make the LMC6061 ideally suited for battery powered applications. Other applications using the LMC6061 include precision full-wave rectifiers, integrators, references, sample-and-hold circuits, and true instrumentation amplifiers. This device is built with National's advanced double-Poly Silicon-Gate CMOS process. For designs that require higher speed, see the LMC6081 precision single operational amplifier. For a dual or quad operational amplifier with similar features, see the LMC6062 or LMC6064 respectively. PATENT PENDING n n n n n n n Ultra low supply current: 20 A Operates from 4.5V to 15V single supply Ultra low input bias current: 10 fA Output swing within 10 mV of supply rail, 100k load Input common-mode range includes V- High voltage gain: 140 dB Improved latchup immunity Applications n n n n n n n Instrumentation amplifier Photodiode and infrared detector preamplifier Transducer amplifiers Hand-held analytic instruments Medical instrumentation D/A converter Charge amplifier for piezoelectric transducers Features (Typical Unless Otherwise Noted) n Low offset voltage: 100 V Connection Diagram Distribution of LMC6061 Input Offset Voltage (TA = +25C) 8-Pin DIP/SO 01142201 Top View 01142215 (c) 2001 National Semiconductor Corporation DS011422 www.national.com LMC6061 Precision CMOS Single Micropower Operational Amplifier April 2001 LMC6061 Absolute Maximum Ratings (Note 1) Current at Power Supply Pin If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Temperature Range (V-) -0.3V Supply Voltage (V+ - V-) Output Short Circuit to V Thermal Resistance (JA) (Note 11) 260C (Soldering, 10 sec.) Storage Temp. Range N Package, 8-Pin Molded DIP -65C to +150C Junction Temperature 150C ESD Tolerance (Note 4) 2 kV 10 mA Current at Input Pin 4.5V V+ 15.5V Supply Voltage (Note 2) Lead Temperature -40C TJ +85C LMC6061AI, LMC6082I (Note 10) Output Short Circuit to V- -55C TJ +125C LMC6061AM 16V + (Note 3) Operating Ratings (Note 1) (V+) +0.3V, Voltage at Input/Output Pin 40 mA Power Dissipation Supply Voltage Differential Input Voltage 30 mA Current at Output Pin 115C/W M Package, 8-Pin Surface Mount 193C/W Power Dissipation (Note 9) DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C. Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = 2.5V and RL > 1M unless otherwise specified. Symbol VOS TCVOS Parameter Conditions Input Offset Voltage Typ LMC6061AM LMC6061AI (Note 9) Limit Limit Limit (Note 6) (Note 6) (Note 6) 100 Input Offset Voltage LMC6061I Units 350 350 800 V 1200 900 1300 Max 1.0 V/C Average Drift IB Input Bias Current 0.010 pA 100 IOS Input Offset Current RIN Input Resistance CMRR Common Mode 4 4 0.005 pA 100 2 2 Max Tera > 10 0V VCM 12.0V Max 85 + 75 75 66 dB 70 72 63 Min 75 75 66 dB 70 72 63 Min 84 74 dB Min Rejection Ratio V = 15V Positive Power Supply 5V V+ 15V Rejection Ratio VO = 2.5V -PSRR Negative Power Supply 0V V- -10V 100 84 70 81 71 VCM Input Common-Mode V+ = 5V and 15V -0.4 -0.1 -0.1 -0.1 V Voltage Range for CMRR 60 dB 0 0 0 Max V+ - 2.3 V+ - 2.3 V+ - 2.3 V V+ - 2.5 Min +PSRR 85 Rejection Ratio V+ - 1.9 + V - 2.6 AV Large Signal RL = 100 k Voltage Gain (Note 7) Sourcing 4000 Sinking RL = 25 k 3000 V - 2.5 400 400 300 V/mV 200 300 200 Min 180 180 90 V/mV 70 100 60 Min V/mV Sourcing 3000 400 400 200 150 150 80 Min Sinking 2000 100 100 70 V/mV 35 50 35 Min (Note 7) www.national.com + 2 (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C. Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = 2.5V and RL > 1M unless otherwise specified. Symbol VO Parameter Output Swing Conditions V+ = 5V Typ LMC6061AM LMC6061AI LMC6061I (Note 9) Limit Limit Limit (Note 6) (Note 6) (Note 6) 4.990 4.990 4.950 V 4.970 4.980 4.925 Min 0.010 0.010 0.050 V 0.030 0.020 0.075 Max 4.975 4.975 4.950 V 4.955 4.965 4.850 Min 0.020 0.020 0.050 V 0.045 0.035 0.150 Max 14.975 14.975 14.950 V 14.955 14.965 14.925 Min 0.025 0.025 0.050 V 0.050 0.035 0.075 Max 14.900 14.900 14.850 V 14.800 14.850 14.800 Min 0.050 0.050 0.100 V 0.200 0.150 0.200 Max 16 16 13 mA 8 10 8 Min 16 16 mA Min 4.995 RL = 100 k to 2.5V 0.005 V+ = 5V 4.990 RL = 25 k to 2.5V 0.010 V+ = 15V 14.990 RL = 100 k to 7.5V 0.010 V+ = 15V 14.965 RL = 25 k to 7.5V 0.025 IO Output Current Sourcing, VO = 0V 22 V+ = 5V IO Output Current Sinking, VO = 5V 21 16 7 8 8 Sourcing, VO = 0V 25 15 15 15 mA 9 10 10 Min 26 20 20 20 mA 7 8 8 Min 20 24 24 32 A 35 32 40 Max 30 30 40 A 40 38 48 Max V+ = 15V Sinking, VO = 13V (Note 10) IS Supply Current Units V+ = +5V, VO = 1.5V V+ = +15V, VO = 7.5V 24 AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = 2.5V and RL > 1M unless otherwise specified. Typ Symbol Parameter SR Slew Rate GBW Gain-Bandwidth Product Conditions (Note 5) (Note 8) 35 Limit Limit Limit (Note 6) (Note 6) (Note 6) 20 20 15 8 10 7 Units V/ms Min 100 kHz 50 Deg m Phase Margin en Input-Referred Voltage Noise F = 1 kHz 83 in Input-Referred Current Noise F = 1 kHz 0.0002 T.H.D. Total Harmonic Distortion F = 1 kHz, AV = -5 RL = 100 k, VO = 2 VPP LMC6061AM LMC6061AI LMC6061I 0.01 % 5V Supply 3 www.national.com LMC6061 DC Electrical Characteristics LMC6061 AC Electrical Characteristics (Continued) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Applies to both single-supply and split-supply operation. Continous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output currents in excess of 30 mA over long term may adversely affect reliability. Note 3: The maximum power dissipation is a function of TJ(Max), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(Max) - TA)/JA. Note 4: Human body model, 1.5 k in series with 100 pF. Note 5: Typical values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V VO 11.5V. For Sinking tests, 2.5V VO 7.5V. Note 8: V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates. Note 9: For operating at elevated temperatures the device must be derated based on the thermal resistance JA with PD = (TJ-TA)/JA. Note 10: Do not connect output to V+, when V+ is greater than 13V or reliability witll be adversely affected. Note 11: All numbers apply for packages soldered directly into a PC board. Note 12: For guaranteed Military Temperature Range parameters see RETSMC6061X. www.national.com 4 VS = 7.5V, TA = 25C, Unless otherwise specified Distribution of LMC6061 Input Offset Voltage (TA = -55C) Distribution of LMC6061 Input Offset Voltage (TA = +25C) 01142215 01142216 Distribution of LMC6061 Input Offset Voltage (TA = +125C) Input Bias Current vs Temperature 01142218 01142217 Supply Current vs Supply Voltage Input Voltage vs Output Voltage 01142219 01142220 5 www.national.com LMC6061 Typical Performance Characteristics LMC6061 Typical Performance Characteristics VS = 7.5V, TA = 25C, Unless otherwise specified (Continued) Common Mode Rejection Ratio vs Frequency Power Supply Rejection Ratio vs Frequency 01142221 01142222 Input Voltage Noise vs Frequency Output Characteristics Sourcing Current 01142223 01142224 Gain and Phase Response vs Temperature (-55C to +125C) Output Characteristics Sinking Current 01142226 01142225 www.national.com 6 LMC6061 Typical Performance Characteristics VS = 7.5V, TA = 25C, Unless otherwise specified (Continued) Gain and Phase Response vs Capacitive Load with RL = 20 k Gain and Phase Response vs Capacitive Load with RL = 500 k 01142227 01142228 Open Loop Frequency Response Inverting Small Signal Pulse Response 01142230 01142229 Inverting Large Signal Pulse Response Non-Inverting Small Signal Pulse Response 01142231 01142232 7 www.national.com LMC6061 Typical Performance Characteristics VS = 7.5V, TA = 25C, Unless otherwise specified (Continued) Non-Inverting Large Signal Pulse Response Stability vs Capacitive Load, RL = 20 k 01142233 01142234 Stability vs Capacitive Load RL = 1 M 01142235 www.national.com 8 AMPLIFIER TOPOLOGY location of the dominate pole is affected by the resistive load on the amplifier. Capacitive load driving capability can be optimized by using an appropriate resistive load in parallel with the capacitive load (see typical curves). The LMC6061 incorporates a novel op-amp design topology that enables it to maintain rail-to-rail output swing even when driving a large load. Instead of relying on a push-pull unity gain output buffer stage, the output stage is taken directly from the internal integrator, which provides both low output impedance and large gain. Special feed-forward compensation design techniques are incorporated to maintain stability over a wider range of operating conditions than traditional micropower op-amps. These features make the LMC6061 both easier to design with, and provide higher speed than products typically found in this ultra-low power class. Direct capacitive loading will reduce the phase margin of many op-amps. A pole in the feedback loop is created by the combination of the op-amp's output impedance and the capacitive load. This pole induces phase lag at the unity-gain crossover frequency of the amplifier resulting in either an oscillatory or underdamped pulse response. With a few external components, op amps can easily indirectly drive capacitive loads, as shown in Figure 2. COMPENSATING FOR INPUT CAPACITANCE It is quite common to use large values of feedback resistance for amplifiers with ultra-low input current, like the LMC6061. Although the LMC6061 is highly stable over a wide range of operating conditions, certain precautions must be met to achieve the desired pulse response when a large feedback resistor is used. Large feedback resistors and even small values of input capacitance, due to transducers, photodiodes, and circuit board parasitics, reduce phase margins. When high input impedances are demanded, guarding of the LMC6061 is suggested. Guarding input lines will not only reduce leakage, but lowers stray input capacitance as well. (See Printed-Circuit-Board Layout for High Impedance Work). The effect of input capacitance can be compensated for by adding a capacitor. Place a capacitor, Cf, around the feedback resistor (as in Figure 1) such that: 01142204 FIGURE 2. LMC6061 Noninverting Gain of 10 Amplifier, Compensated to Handle Capacitive Loads In the circuit of Figure 2, R1 and C1 serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Capacitive load driving capability is enhanced by using a pull up resistor to V+ Figure 3. Typically a pull up resistor conducting 10 A or more will significantly improve capacitive load responses. The value of the pull up resistor must be determined based on the current sinking capability of the amplifier with respect to the desired output swing. Open loop gain of the amplifier can also be affected by the pull up resistor (see electrical characteristics). or R1 CIN R2 Cf Since it is often difficult to know the exact value of CIN, Cf can be experimentally adjusted so that the desired pulse response is achieved. Refer to the LMC660 and the LMC662 for a more detailed discussion on compensating for input capacitance. 01142205 FIGURE 1. Canceling the Effect of Input Capacitance 01142214 CAPACITIVE LOAD TOLERANCE All rail-to-rail output swing operational amplifiers have voltage gain in the output stage. A compensation capacitor is normally included in this integrator stage. The frequency FIGURE 3. Compensating for Large Capacitive Loads with a Pull Up Resistor 9 www.national.com LMC6061 Applications Hints LMC6061 Applications Hints terminals of capacitors, diodes, conductors, resistors, relay terminals etc. connected to the op-amp's inputs, as in Figure 4. To have a significant effect, guard rings should be placed on both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of the input. This would cause a 100 times degradation from the LMC6061's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a resistance of 1011 would cause only 0.05 pA of leakage current. See Figure 5 for typical connections of guard rings for standard op-amp configurations. (Continued) PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the LMC6061, typically less than 10 fA, it is essential to have an excellent layout. Fortunately, the techniques of obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6061's inputs and the 01142206 FIGURE 4. Example of Guard Ring in P.C. Board Layout www.national.com 10 LMC6061 Applications Hints (Continued) 01142210 (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board). 01142207 Inverting Amplifier FIGURE 6. Air Wiring Latchup CMOS devices tend to be susceptible to latchup due to their internal parasitic SCR effects. The (I/O) input and output pins look similar to the gate of the SCR. There is a minimum current required to trigger the SCR gate lead. The LMC6061 and LMC6081 are designed to withstand 100 mA surge current on the I/O pins. Some resistive method should be used to isolate any capacitance from supplying excess current to the I/O pins. In addition, like an SCR, there is a minimum holding current for any latchup mode. Limiting current to the supply pins will also inhibit latchup susceptibility. 01142208 Non-Inverting Amplifier Typical Single-Supply Applications (V+ = 5.0 VDC) 01142209 The extremely high input impedance, and low power consumption, of the LMC6061 make it ideal for applications that require battery-powered instrumentation amplifiers. Examples of these types of applications are hand-held pH probes, analytic medical instruments, magnetic field detectors, gas detectors, and silicon based pressure transducers. Follower FIGURE 5. Typical Connections of Guard Rings The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 6. Figure 7 shows an instrumentation amplifier that features high differential and common mode input resistance ( > 1014), 0.01% gain accuracy at AV = 100, excellent CMRR with 1 k imbalance in bridge source resistance. Input current is less than 100 fA and offset drift is less than 2.5 V/C. R2 provides a simple means of adjusting gain over a wide range without degrading CMRR. R7 is an initial trim used to maximize CMRR without using super precision matched resistors. For good CMRR over temperature, low drift resistors should be used. 11 www.national.com LMC6061 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) 01142211 If R1 = R5, R3 = R6, and R4 = R7; then AV 100 for circuit shown (R2 = 9.822k). FIGURE 7. Instrumentation Amplifier 01142212 FIGURE 8. Low-Leakage Sample and Hold www.national.com 12 LMC6061 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) 01142213 FIGURE 9. 1 Hz Square Wave Oscillator Ordering Information Package Temperature Range Military Industrial -55C to +125C Transport Media N08E Rail -40C to +85C 8-Pin LMC6061AIN Molded DIP LMC6061IN 8-Pin LMC6061AIM, LMC606AIMX Small Outline LMC6061IM, LMC6061IMX 8-Pin NSC Drawing LMC6061AMJ/883 M08A Rail Tape and Reel J08A Rail Ceramic DIP 13 www.national.com LMC6061 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin Ceramic Dual-In-Line Package Order Number LMC6061AMJ/883 NS Package Number J08A www.national.com 14 LMC6061 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 8-Pin Small Outline Package Order Number LMC6061AIM, LMC6061AIMX, LMC6061IM or LMC6061IMX NS Package Number M08A 8-Pin Molded Dual-In-Line Package Order Number LMC6061AIN or LMC6061IN NS Package Number N08E 15 www.national.com LMC6061 Precision CMOS Single Micropower Operational Amplifier Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated