MC100LVEP11D - ON Semiconductor

 Semiconductor Components Industries, LLC, 2005

February, 2005 − Rev. 7

1Publication Order Number:

MC10LVEP11/D

MC10LVEP11, MC100LVEP11

2.5V / 3.3VECL 1:2

Differential Fanout Buffer

The MC10/100LVEP11 is a differential 1:2 fanout buffer. The

device is pin and functionally equivalent to the EP11 device. With AC

performance the same as the EP11 device, the LVEP11 is ideal for

applications requiring lower voltage. Single−ended CLK input

operation is limited to a VCC w 3.0 V in PECL mode, or VEE v

−3.0 V in NECL mode.

The 100 Series contains temperature compensation.

•240 ps Typical Propagation Delay

•Maximum Frequency > 3.0 GHz Typical

•PECL Mode Operating Range: VCC = 2.375 V to 3.8 V

with VEE = 0 V

•NECL Mode Operating Range: VCC = 0 V

with VEE = −2.375 V to −3.8 V

•Open Input Default State

•Q Output Will Default LOW with Inputs Open or at VEE

•LVDS Input Compatible

*For additional marking information, refer to

Application Note AND8002/D.

H = MC10

K = MC100

A = Assembly Location

L = Wafer Lot

Y = Year

W = Work Week

ALYW

HU11

ALYW

KU11

MARKING

DIAGRAMS*

SOIC−8

D SUFFIX

CASE 751

TSSOP−8

DT SUFFIX

CASE 948R

See detailed ordering and shipping information in the package

dimensions section on page 8 of this data sheet.

ORDERING INFORMATION

http://onsemi.com

8HYP11

AYWW

KYP11

AYWW

MC10LVEP11, MC100LVEP11

http://onsemi.com

VEE

VCC

DQ1

Figure 1. 8−Lead Pinout (Top View) and Logic

Diagram

Table 1. PIN DESCRIPTION

PIN FUNCTION

D*, D** ECL Data Inputs

Q0, Q0, Q1, Q1 ECL Data Outputs

VCC Positive Supply

VEE Negative Supply

*Pins will default to 2/3 VCC when left open.

**Pins will default LOW when left open.

Table 2. ATTRIBUTES

Characteristics Value

Internal Input Pulldown Resistor 75 kW

Internal Input Pullup Resistor 37.5 kW

ESD Protection Human Body Model

Machine Model

Charged Device Model

> 4 kV

> 200 V

> 2 kV

Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Level 1

Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in

Transistor Count 110 Devices

Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test

1. For additional information, see Application Note AND8003/D.

MC10LVEP11, MC100LVEP11

http://onsemi.com

Table 3. MAXIMUM RATINGS

Symbol Parameter Condition 1 Condition 2 Rating Unit

VCC PECL Mode Power Supply VEE = 0 V 6 V

VEE NECL Mode Power Supply VCC = 0 V −6 V

VIPECL Mode Input Voltage

NECL Mode Input Voltage

VEE = 0 V

VCC = 0 V

VI v VCC

VI w VEE

−6

Iout Output Current Continuous

Surge

100

TAOperating Temperature Range −40 to +85 °C

Tstg Storage Temperature Range −65 to +150 °C

qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm

500 lfpm

SOIC−8

190

130

°C/W

qJC Thermal Resistance (Junction−to−Case) Standard Board SOIC−841 to 44 °C/W

qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm

500 lfpm

TSSOP−8

185

140

°C/W

qJC Thermal Resistance (Junction−to−Case) Standard Board TSSOP−841 to 44 °C/W

Tsol Wave Solder <2 to 3 sec @ 248°C 265 °C

Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit

values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,

damage may occur and reliability may be affected.

MC10LVEP11, MC100LVEP11

http://onsemi.com

Table 4. 10LVEP DC CHARACTERISTICS, PECL VCC = 2.5 V, VEE = 0 V (Note 2)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

IEE Power Supply Current 24 30 36 24 30 36 25 31 38 mA

VOH Output HIGH Voltage (Note 3) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV

VOL Output LOW Voltage (Note 3) 565 740 865 630 805 930 690 865 990 mV

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 4)

1.2 2.5 1.2 2.5 1.2 2.5 V

IIH Input HIGH Current 150 150 150 mA

IIL Input LOW Current D

0.5

−150

0.5

−150

0.5

−150

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.125 V to −1.3 V.

3. All loading with 50 W to VCC − 2.0 V.

4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential

input signal. Single−Ended input CLK pin operation is limited to VCC w 3.0 V in PECL mode.

Table 5. 10LVEP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 5)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

IEE Power Supply Current 24 30 36 24 30 36 25 31 38 mA

VOH Output HIGH Voltage (Note 6) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV

VOL Output LOW Voltage (Note 6) 1365 1540 1665 1430 1605 1730 1490 1665 1790 mV

VIH Input HIGH Voltage (Single−Ended)

(Note 7)

2090 2415 2155 2480 2215 2540 mV

VIL Input LOW Voltage (Single−Ended)

(Note 7)

1365 1690 1430 1755 1490 1815 mV

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 8)

1.2 3.3 1.2 3.3 1.2 3.3 V

IIH Input HIGH Current 150 150 150 mA

IIL Input LOW Current D

0.5

−150

0.5

−150

0.5

−150

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

5. Input and output parameters vary 1:1 with VCC. VEE can vary +0.925 V to −0.5 V.

6. All loading with 50 W to VCC − 2.0 V.

7. Single−Ended input CLK pin operation is limited to VCC w 3.0 V in PECL mode.

8. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential

input signal.

MC10LVEP11, MC100LVEP11

http://onsemi.com

Table 6. 10LVEP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −3.8 V to −2.375 V (Note 9)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

IEE Power Supply Current 24 30 36 24 30 36 25 31 38 mA

VOH Output HIGH Voltage (Note 10) −1135 −1010 −885 −1070 −945 −820 −1010 −885 −760 mV

VOL Output LOW Voltage (Note 10) −1935 −1760 −1635 −1870 −1695 −1570 −1810 −1635 −1510 mV

VIH Input HIGH Voltage (Single−Ended)

(Note 11)

−1210 −885 −1145 −820 −1085 −760 mV

VIL Input LOW Voltage (Single−Ended)

(Note 11)

−1935 −1610 −1870 −1545 −1810 −1485 mV

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 12)

VEE+1.2 0.0 VEE+1.2 0.0 VEE+1.2 0.0 V

IIH Input HIGH Current 150 150 150 mA

IIL Input LOW Current D

0.5

−150

0.5

−150

0.5

−150

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

9. Input and output parameters vary 1:1 with VCC.

10.All loading with 50 W to VCC − 2.0 V.

11. Single−Ended input CLK pin operation is limited to VEE v −3.0 V in NECL mode.

12.VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential

input signal.

Table 7. 100LVEP DC CHARACTERISTICS, PECL VCC = 2.5 V, VEE = 0 V (Note 13)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

IEE Power Supply Current 25 31 37 29 35 41 32 38 45 mA

VOH Output HIGH Voltage (Note 14) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV

VOL Output LOW Voltage (Note 14) 555 730 900 555 730 900 555 730 900 mV

VIH Input HIGH Voltage (Single−Ended) 1335 1620 1335 1620 1335 1620 mV

VIL Input LOW Voltage (Single−Ended) 555 900 555 900 555 900 mV

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 15)

1.2 2.5 1.2 2.5 1.2 2.5 V

IIH Input HIGH Current 150 150 150 mA

IIL Input LOW Current D

0.5

−150

0.5

−150

0.5

−150

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

13.Input and output parameters vary 1:1 with VCC. VEE can vary +0.125 V to −1.3 V.

14.All loading with 50 W to VCC − 2.0 V.

15.VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential

input signal. Single−Ended input CLK pin operation is limited to VCC w 3.0 V in PECL mode.

MC10LVEP11, MC100LVEP11

http://onsemi.com

Table 8. 100LVEP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 16)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

IEE Power Supply Current 25 31 37 29 35 41 32 38 45 mA

VOH Output HIGH Voltage (Note 17) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV

VOL Output LOW Voltage (Note 17) 1355 1530 1700 1355 1530 1700 1355 1530 1700 mV

VIH Input HIGH Voltage (Single−Ended)

(Note 18)

2135 2420 2135 2420 2135 2420 mV

VIL Input LOW Voltage (Single−Ended)

(Note 18)

1355 1700 1355 1700 1355 1700 mV

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 19)

1.2 3.3 1.2 3.3 1.2 3.3 V

IIH Input HIGH Current 150 150 150 mA

IIL Input LOW Current D

0.5

−150

0.5

−150

0.5

−150

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

16.Input and output parameters vary 1:1 with VCC. VEE can vary +0.925 V to −0.5 V.

17.All loading with 50 W to VCC − 2.0 V.

18.Single−Ended input CLK pin operation is limited to VCC w 3.0 V in PECL mode.

19.VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential

input signal.

Table 9. 100LVEP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −3.8 V to −2.375 V (Note 20)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

IEE Power Supply Current 25 31 37 29 35 41 32 38 45 mA

VOH Output HIGH Voltage (Note 21) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV

VOL Output LOW Voltage (Note 21) −1945 −1770 −1600 −1945 −1770 −1600 −1945 −1770 −1600 mV

VIH Input HIGH Voltage (Single−Ended)

(Note 22)

−1165 −880 −1165 −880 −1165 −880 mV

VIL Input LOW Voltage (Single−Ended)

(Note 22)

−1945 −1425 −1600 −1945 −1425 −1600 −1945 −1425 −1600 mV

VIHCMR Input HIGH Voltage Common Mode

Range (Differential Configuration)

(Note 23)

VEE+1.2 0.0 VEE+1.2 0.0 VEE+1.2 0.0 V

IIH Input HIGH Current 150 150 150 mA

IIL Input LOW Current D

0.5

−150

0.5

−150

0.5

−150

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

20.Input and output parameters vary 1:1 with VCC.

21.All loading with 50 W to VCC − 2.0 V.

22.Single−Ended input CLK pin operation is limited to VEE  −3.0 V in NECL mode.

23.VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential

input signal.

MC10LVEP11, MC100LVEP11

http://onsemi.com

Table 10. AC CHARACTERISTICS VCC = 0 V; VEE = −3.8 V to −2.375 V or VCC = 2.375 V to 3.8 V; VEE = 0 V (Note 24)

−40°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit

fmax Maximum Frequency (Figure 2) 3 3 3 GHz

tPLH,

tPHL

Propagation Delay

(Differential Configuration)

CLK to Q, Q

170 230 300 180 240 310 210 270 360 ps

tSKEW Within Device Skew Q, Q

Device to Device Skew (Note 25)

5.0 20

130

5.0 20

130

5.0 20

150

tJITTER CLOCK Random Jitter (RMS)

@ v3.0 GHz (Figure 2)

0.2 1 0.2 1 0.2 1 ps

VPP Input Voltage Swing

(Differential Configuration)

150 800 1200 150 800 1200 150 800 1200 mV

Output Rise/Fall Times Q, Q

(20% − 80%)

70 110 170 80 120 180 100 140 200 ps

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

24.Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.

25.Skew is measured between outputs under identical transitions.

100

200

300

400

500

600

700

800

900

1000

0 1000 2000 3000 4000

FREQUENCY (MHz)

Figure 2. Fmax Typical

VOUTpp (mV)

3.3 V

2.5 V

MC10LVEP11, MC100LVEP11

http://onsemi.com

Figure 3. Typical Termination for Output Driver and Device Evaluation

(See Application Note AND8020/D − Termination of ECL Logic Devices.)

Driver

Device

Receiver

Device

Q D

Zo = 50 W

50 W50 W

VTT

VTT = VCC − 2.0 V

ORDERING INFORMATION

Device Package Shipping†

MC10LVEP11D SOIC−898 Units / Rail

MC10LVEP11DR2 SOIC−82500 / Tape & Reel

MC10LVEP11DT TSSOP−8100 Units / Rail

MC10LVEP11DTR2 TSSOP−82500 / Tape & Reel

MC100LVEP11D SOIC−898 Units / Rail

MC100LVEP11DR2 SOIC−82500 / Tape & Reel

MC100LVEP11DT TSSOP−8100 Units / Rail

MC100LVEP11DTR2 TSSOP−82500 / Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

Resource Reference of Application Notes

AN1405/D −ECL Clock Distribution Techniques

AN1406/D −Designing with PECL (ECL at +5.0 V)

AN1503/D −ECLinPSt I/O SPiCE Modeling Kit

AN1504/D −Metastability and the ECLinPS Family

AN1568/D −Interfacing Between LVDS and ECL

AN1642/D −The ECL Translator Guide

AND8001/D −Odd Number Counters Design

AND8002/D −Marking and Date Codes

AND8020/D −Termination of ECL Logic Devices

AND8066/D −Interfacing with ECLinPS

AND8090/D −AC Characteristics of ECL Devices

MC10LVEP11, MC100LVEP11

http://onsemi.com

PACKAGE DIMENSIONS

SEATING

PLANE

X 45 _

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSION A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL

IN EXCESS OF THE D DIMENSION AT

MAXIMUM MATERIAL CONDITION.

6. 751−01 THRU 751−06 ARE OBSOLETE. NEW

STANDARD IS 751−07.

0.10 (0.004)

DIM

MIN MAX MIN MAX

INCHES

4.80 5.00 0.189 0.197

MILLIMETERS

B3.80 4.00 0.150 0.157

C1.35 1.75 0.053 0.069

D0.33 0.51 0.013 0.020

G1.27 BSC 0.050 BSC

H0.10 0.25 0.004 0.010

J0.19 0.25 0.007 0.010

K0.40 1.27 0.016 0.050

M0 8 0 8

N0.25 0.50 0.010 0.020

S5.80 6.20 0.228 0.244

−X−

−Y−

0.25 (0.010)

−Z−

0.25 (0.010) Z SXS

____

SOIC−8 NB

CASE 751−07

ISSUE AE

1.52

0.060

7.0

0.275

0.6

0.024

1.270

0.050

4.0

0.155

ǒmm

inchesǓ

SCALE 6:1

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

MC10LVEP11, MC100LVEP11

http://onsemi.com

PACKAGE DIMENSIONS

TSSOP−8

DT SUFFIX

PLASTIC TSSOP PACKAGE

CASE 948R−02

ISSUE A

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A2.90 3.10 0.114 0.122

B2.90 3.10 0.114 0.122

C0.80 1.10 0.031 0.043

D0.05 0.15 0.002 0.006

F0.40 0.70 0.016 0.028

G0.65 BSC 0.026 BSC

L4.90 BSC 0.193 BSC

M0 6 0 6

____

SEATING

PLANE

PIN 1

DETAIL E

2X L/2

−U−

U0.15 (0.006) T

0.10 (0.004) V S

0.10 (0.004)

−T−

−V−

−W−

0.25 (0.010)

8x REFK

IDENT

K0.25 0.40 0.010 0.016

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.

PROTRUSIONS OR GATE BURRS. MOLD FLASH

OR GATE BURRS SHALL NOT EXCEED 0.15

(0.006) PER SIDE.

4. DIMENSION B DOES NOT INCLUDE INTERLEAD

FLASH OR PROTRUSION. INTERLEAD FLASH OR

PROTRUSION SHALL NOT EXCEED 0.25 (0.010)

PER SIDE.

5. TERMINAL NUMBERS ARE SHOWN FOR

REFERENCE ONLY.

6. DIMENSION A AND B ARE TO BE DETERMINED

AT DATUM PLANE −W−.

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Japan: ON Semiconductor, Japan Customer Focus Center

2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051

Phone: 81−3−5773−3850

MC10LVEP11/D

ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC).

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 61312, Phoenix, Arizona 85082−1312 USA

Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada

Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: http://onsemi.com

Order Literature: http://www.onsemi.com/litorder

For additional information, please contact your

local Sales Representative.